EAPL

Model ST-10M1 FUNCTION

On power application and shorting of S1 & S2
INSTRUCTION MANUAL terminals, the timing sequence of the 1st channel is
initiated by switching On RLY0 and ontime starts.
ST-10M1 SEQUENTIAL TIMER WITH 10 CHANNELS After completion of ontime of RLY0 offtime starts.
www.eaplindia.com After completion of the offtime of RLY0, RLY1 comes
ON and ontime starts followed by offtime this cycle

DIMENSION
continues for rest of the sequences.

A1,A2 : Source

S1-S2 : Start signal for a minimum of 150mS.

C1-C2 : SHORT – Single cycle operation(i.e timer
stops at the end of one cycle)
OPEN – Cyclic operation (i.e. timer
continues to operate).
O1-O2: Cycle Complete Output. This output is
available after completion of 1 cycle in single cycle
operation mode (C1-C2 shorted).
I1-I2 : Time Pause Input. By shorting these

FRONT VIEW
terminals timing is temporarily stopped and relay
status maintained, again by opening timing
continues.
COPY : SHORT – First channel program shall be
copied to all 10 channels during program mode.
OPEN – Individual channel shall be
programmed with different values.
HOLD MODE: Continue the timing after resumption
of interrupted power.
RESTART MODE: After the resumption of interrupted
power operation starts from the sequence 0 or waits
for the start signal if C1–C2 is shorted.

DOC NO.: OD RS YN 19001 0 REV NO.: 01 Dtd: 20/05/2014 Page 1 of 4

CREATED ON: May 20, 2014

Programming Instruction: Copy Channel Programming:

Timing Example:-  Short copy terminals.

CHNL 3 : ONTIME 39.50Min  Slide RUN/PROG switch to PROG mode.
OFFTIME 45.30Sec  Program the required readings for ON & OFF (1st channel) as per the
programming instruction.
 Slide RUN/PROG switch to PROG mode; Sequence
display shows “0”,ON LED glows, Previously
 1st channel program is copied to all the channels.
programmed timing & range is displayed.  Slide the RUN/PROG switch back to RUN mode.
 Press “SEQUENCE” button till display shows ‘3’.
ON TIME: -
 Press “RANGE” button till “MIN SEC” LED glows.
 Press “SELECT” button, MSD starts flashing. STATUS
 Press “ADVANCE” till display shows ‘3’, press
nd
“SELECT” again; 2 digit starts flashing. OPERATING TIMING IN TIMING
CONDITION/MODE TIMING PROGRESS(TIP) COMPLETION(TC)
 Press “ADVANCE” till display shows 9.
rd SEQUENCE
 Press “SELECT” again; 3 digit starts flashing. RELAY LED RELAY LED
 Press “ADVANCE” till display shows 5.
 Press “SELECT” again; 4th digit (LSD) starts flashing. ON TIME RLY1 ON ON - OFF
 Press “ADVANCE” till display shows 0. SEQUENCE 0
 Press “SELECT” again; the SET value is saved in OFF TIME RLY1 OFF OFF - OFF
memory depending on the selection of ‘COPY’
terminals. ON TIME RLY2 ON ON - OFF
OFF TIME:- SEQUENCE 1
 Press ON/OFF switch to select OFF time (OFF LED
OFF TIME RLY2 OFF OFF - OFF
glows).
 Press “RANGE” button till “SEC SEC” LED glows.
 Press “SELECT” button, MSD starts flashing. ON TIME RLY3 ON ON - OFF
 Press “ADVANCE” till display shows ‘4’. Press SEQUENCE 2
nd
“SELECT” again; 2 digit starts flashing. OFF TIME RLY3 OFF OFF - OFF
 Press “ADVANCE” till display shows 5.
rd
 Press “SELECT” again; 3 digit starts flashing.
ON TIME RLY4 ON ON - OFF
 Press “ADVANCE” till display shows 3. SEQUENCE 3 & so
th
 Press “SELECT” again; 4 digit (LSD) starts flashing onC.
0. OFF TIME RLY4 OFF OFF - OFF
 Press “SELECT” again; the SET value is saved in
memory depending on the selection of ‘COPY’
terminals.
Slide RUN/PROG switch to RUN mode; now the timer is ready
for operation. Same procedure shall be followed for different
ranges and for different timing requirement.

CREATED ON: May 20, 2014

DOC NO.: OD RS YN 19001 0 Dtd: 20/05/2014 Page 2 of 4
1) Cascading of two Sequential timers
DISPOSITION CONTACT
EAPL Sequential timers with O1- O2 & S1- S2 Fecility
can be cascaded to get more no of channels. Once the product life is over, you may Electronic Automation Pvt. Ltd
send back the unit to EAPL for #20, KHB Industrial area
Single cycle operation disposition. Yelahanka
Bangalore -64
Connect O1 of the First timer to S1 of Second timer &
O2 of the first timer to S2 of Second timer. TROUBLE ANALYSIS Ph:+91-80-
C1-C2 of both timers shall be shorted for Single 28567561/2/42802345
operation. S1-S2 of first timer shall be Shorted manually
Timing not initiated.
to initiate the Function. Refer: Page No:04 of 04 Email :

S1- S2 start signal shall be
applied. [email protected]
HINTS ON CORRECT USAGE www.eaplindia.com

Use proper gauge wires for connections.

Ensure all terminals are tightly screwed.

Source Voltage should not exceed specified limits. It
will damage the unit beyond repair.

CAUTION

Shorting of S1-S2 shall be potential free;
applying power to these terminals will damage
the timer permanently.

CREATED ON: May 20, 2014

DOC NO.: OD RS YN 19001 0 Dtd: 20/05/2014 Page 3 of 4
 Cascading of two Sequential timers

CREATED ON: May 20, 2014

DOC NO.: OD RS YN 19001 0 Dtd: 20/05/2014 Page 4 of 4