CMP CMP PRODUCTS

PRODUCTS CABLE
CABLE GLAND
GLAND CATALOGUECMP CMP
CATALOGUE

E
F

GLAND PRODUCTS
GLANDS
D B C
A

SPECIFICATION
T3CDS TECHNICAL DATA

AMERICANCABLE
Design Specification BS 6121:Part 1:1989, IEC 62444, EN 62444
Mechanical Classification* Impact = Level 8, Retention = Class D

Triton CDS (T3CDS) Globally Approved,

INDUSTRIAL
Enclosure Protection IK10 to IEC 62262 (20 joules) Brass & Stainless Steel only
Category B (Category A when used with braid, tape or pliable wire armour
Hazardous (Classified) Location Cable Gland Electrical Classification*
cables)
ATEX Certificate SIRA13ATEX1073X, SIRA13ATEX4079X
^ II 2G,II 1D, Ex d IIC Gb, Ex e IIC Gb, Ex ta IIIC Da,
For all types of Armoured Cables Code of Protection
^ II 3G Ex nR IIC Gc, ^ I M2, Ex d I Mb, Ex e I Mb

NORTH
Compliance Standards EN60079-0,1,7,15,31
• Fully sequential, three step installation procedure

CMP CMP
IECEx Certificate IECEx SIR 13.0028X, IECEx SIM 14.0007X
• Reduces installation times, cost & risk Code of Protection Ex d IIC Gb, Ex e IIC Gb, Ex nR IIC Gc, Ex ta IIIC Da, Ex d I Mb, Ex e I Mb
• Direct & remote installation Compliance Standards IEC 60079-0,1,7,15,31

• Unique compensating displacement seal system (CDS) cCSAus Certificate (20s16 - 90) 1310517
Class I, Div 2, Groups A,B,C and D, Class II, Div 2, Groups E,F and G, Class III,
• Metal-to-metal installation every time regardless of cable diameter Code of Protection Enclosure Type 3, 4 and 4X, Ex d IIC, Ex e IIC, Ex nR II, Class I, Zone 1, AEx e
II, AEx nR II
• Designed to prevent Coldflow CAN/CSA-C22.2 No 0, 18, 25, 30, 94, 174, CAN/CSA-E60079-0, 1, 7,
Compliance Standards
• Integral protected deluge seal ANSI/UL 514B Ed 5, ANSI/UL 50 Ed 11, ANSI/UL 2225 Ed 4, UL60079-0, 1, 7
UL Certificate (20s16 - 90) E200163
• Controlled outer ‘load retention’ seal
Code of Protection Class I, Zone 1, AEx e II
• Unique OSTG prevents overtightening Compliance Standards UL514B
• -76˚F to 266˚F (standard), -4˚F to 392˚F (ThermEx option page 91) EAC Certificate (Formerly GOST R, K & B) TC RU C-GB.ГБ05.B00138
NEPSI Certificate GYJ13.1141X / GYJ13.1283X
• Class I Zone 1, 21 and Zone 2, 22 Class I Division 2 ABCD
CCOE / PESO (India) Certificate P333688
• Globally marked, UL, cCSAus, IECEx & ATEX INMETRO Certificate TUV 11.0374X
• As standard in nickel plated brass with NPT thread form RETIE Certificate 03866
Marine Certificates LRS: 01/00172 (E3), DNV: E-13848, ABS: 14-LD234401A-4-PDA
Ingress Protection Rating IP66, IP67 & IP68 **
Deluge Protection Compliance DTS01 : 91
NEMA Rating NEMA 4X**
Cable Gland Material Electroless Nickel Plated Brass, Copper Free (<0.4%) Aluminium, Stainless Steel
Seal Material CMP SOLO LSF Halogen Free Thermoset Elastomer
† Grooved Cone (X) is predominantly used for Wire Braid (e.g. GSWB, TCWB), Steel Tape Armour
(STA, DSTA) and Aluminium Strip Armour (ASA) but is also suitable for Single Wire Armour (SWA), Steel / Served Wire Armour (SWA), Aluminium Wire Armour (AWA), Pliable
Aluminium Wire Armour (AWA) and Pliable Wire Armour (PWA) if the range is outside that of the Cable Type(s) Wire Armour (PWA), Steel Tape Armour (STA), Aluminium Strip Armour (ASA),
Stepped Cone (W). Screened Flexible (EMC) Wire Braid (e.g CY/SY), Wire Braid Armour (e.g SWB)
Note: Grooved Cone (X) dimensions shown in the Cable Gland Selection Table below are for a Armour Clamping Reversible Armour Cone & AnyWay Universal Clamping Ring
double wire strand of braid armour cables. Tapes can also be doubled over. For cables that have only a
single layer of armour such as SWA the clamping range should be used as shown in the table below. Inner Bedding Sealing Ring: Compensating Displacement Seal (CDS), Outer
Sealing Technique
Sheath Sealing Ring : Load Retention Seal (LRS)
Stepped (W) Cone is suitable for Single Wire Armour (SWA), or Aluminium Wire Armour (AWA) cables.
Sealing Area(s) Cable Inner Bedding & Outer Cable Sheath

Note : * Mechanical & Electrical Classifications applied as per IEC 62444 & EN 62444
Note : ** Refer to page 7 or www.cmp-products.com for further information on Ingress Protection Ratings
Cable Gland Selection Table
Refer to illustration at the top of the page
Cable Armour Range †
Available Entry Threads “C” Across Across Combined Ordering
Bedding Overall Cable Cable
(Alternate Metric Thread Flats Corners Protrusion Reference
Cable
Thread Diameter Diameter “B” Grooved Cone Stepped Cone Gland
Gland Lengths Available) (X) (W) “D” “D” Length (*Nickel Plated Brass NPT) Shroud
Length “E” “A” Weight
Size “F”
NPT Metric Ordering (ozs)
NPT Min Max Min Max Min Max Min Max Max Max Size Type
(Option) (Option) Suffix
20s16 1/2” 3/4” M20 0.78 0.122 0.339 0.240 0.516 0.012 0.040 0.031 0.049 0.945 1.039 3.096 20S16 T3CDS 1RA531 PVC36 7.055
20S 1/2” 3/4” M20 0.78 0.240 0.457 0.374 0.626 0.012 0.040 0.031 0.049 0.945 1.039 3.096 20S T3CDS 1RA531 PVC36 6.914
20 1/2” 3/4” M20 0.78 0.256 0.547 0.492 0.823 0.016 0.040 0.031 0.049 1.201 1.321 2.998 20 T3CDS 1RA531 PVC06 9.771
25S 3/4” 1” M25 0.80 0.437 0.783 0.551 0.866 0.016 0.048 0.049 0.063 1.476 1.624 3.494 25S T3CDS 1RA532 PVC09 15.344
25 3/4” 1” M25 0.80 0.437 0.783 0.717 1.031 0.016 0.048 0.049 0.063 1.476 1.624 3.493 25 T3CDS 1RA532 PVC09 15.344
32 1” 1 1/4” M32 0.98 0.669 1.031 0.933 1.335 0.016 0.048 0.063 0.079 1.811 1.992 3.569 32 T3CDS 1RA533 PVC11 22.328
40 1 1/4” 1 1/2” M40 1.01 0.866 1.264 1.098 1.591 0.016 0.062 0.063 0.079 2.165 2.382 3.667 40 T3CDS 1RA534 PVC15 31.923
50S 1 1/2” 2” M50 1.03 1.161 1.500 1.386 1.839 0.016 0.062 0.079 0.098 2.362 2.598 3.963 50S T3CDS 1RA535 PVC18 39.648
50 2” 2 1/2” M50 1.06 1.402 1.732 1.591 2.087 0.024 0.062 0.079 0.098 2.760 3.036 4.163 50 T3CDS 1RA536 PVC21 56.579
63S 2” 2 1/2” M63 1.06 1.579 1.965 1.795 2.339 0.024 0.062 0.079 0.098 2.953 3.244 4.033 63S T3CDS 1RA536 PVC23 61.095
63 2 1/2” 3” M63 1.57 1.858 2.201 2.150 2.591 0.024 0.062 0.079 0.098 3.150 3.465 4.148 63 T3CDS 1RA537 PVC25 62.717
75S 2 1/2” 3” M75 1.57 2.079 2.437 2.323 2.835 0.024 0.062 0.079 0.098 3.543 3.898 4.352 75S T3CDS 1RA537 PVC28 90.700
75 3” 3 1/2” M75 1.63 2.327 2.673 2.626 3.087 0.024 0.062 0.098 0.118 3.937 4.331 4.734 75S T3CDS 1RA538 PVC30 117.927
90 3 1/2” 4” M90 1.69 2.622 3.094 3.000 3.555 0.032 0.062 0.124 0.157 4.528 4.980 5.467 90 T3CDS 1RA539 PVC32 171.734
100 4” 5” M75 1.73 2.992 3.579 3.390 3.992 0.032 0.062 0.124 0.157 5.000 5.500 5.045 100 T3CDS 1RA5310 LSF33 175.276
115 4” 5” M75 1.73 3.386 3.854 3.996 4.339 0.032 0.062 0.124 0.157 5.433 5.976 6.348 115 T3CDS 1RA5311 LSF34 272.350
130 5” 6” M90 1.84 3.819 4.524 4.339 4.850 0.032 0.062 0.124 0.157 6.000 6.799 6.821 130 T3CDS 1RA5312 LSF35 344.374
*Note : For material options please change the suffix in the Ordering Reference ; Brass (no suffix required), Nickel Plated Brass “5” (as standard), 316 Grade Stainless Steel “4”, Copper Free Aluminium “1”
For NPT options please change the following digits after the material suffix ; 1/2” = 31, 3/4” = 32, 1” = 33, 1 1/4” = 34, 1 1/2” = 35, 2” = 36, 2 1/2” = 37, 3” = 38, 3 1/2” = 39, 4” = 310 (Brass requires prefix “0”)
Examples: 32T3CDS1RA533534 = Nickel Plated Brass 1-1/4” NPT, 50ST3CDS1RA536035 = Brass 1-1/2” NPT, 25T3CDS1RA532432 = Stainless Steel 3/4” NPT, 20T3CDS1RA5315 = Nickel Plated Brass M20
Dimensions are displayed in inches unless otherwise stated

www.cmp-products.com TDS560 ISSUE7 08/15