800 Series Gear Reducers

Worm Gear Reducers

Single Reduction

Built For Industrial Use

Precision mounting surfaces and extra
threaded bolt holes on top and bottom for
flexibility and to accept a wide range of
Worm - Worm Gear Reducers

stock mounting accessories.

Double Reduction

O-rings on input and output

Cast iron IEC and NEMA C input covers eliminate gaskets,
flange with machined fits for sealants and leaks.
precision alignment of motor and
bearings.

Push-off holes drilled

Helical - Worm Gear Reducers

and tapped into flange

for quick motor removal
Double Reduction

on quill input styles

(56 & 140TC frames).
WASHGUARD® Reducers
and GEAR+MOTOR™

Seal Guard** on quill-input styles

protects input seal from damage
during motor installation.

** Sizes 813 through 852 only

IronMan™ fine-grained, one-piece cast

housing for rigidity and alignment.
Ratio Multipliers

Machined for precision alignment

of worm, worm gear, bearings and
mounting surfaces. Superior resistance
to environmental contaminants with high
heat dissipation and noise reduction.
Bronze alloy worm gear is
premium quality bronze for
maximum strength, lubricity and
superior life.

Tapered roller bearings on output shaft for

Accessories

high overhung and thrust load capacities.

Mounting dimensions are
interchangeable with Baldor 900
Premium Grade 5
series, Boston Gear, Browning
zinc-plated heat-
Raider, Falk, Morse Invader and other
treated bolts
“industry standard” reducers.
used throughout.

14 www.grovegear.com
 Table of Contents

Reduction Reducers
Bravo® Single
Page

Right Angle Worm Gear Reducers - Single Reduction

Oversized positively-retained high speed input Introduction...........................................................................................................4
shaft bearing for higher shock load capacity, Quick Selection...................................................................................................16
shaft alignment and seal life. Ideal for frequent Maximum Rating Tables.....................................................................................31
starting and reversing applications.
Weights & Technical Information.......................................................................59
GR Series Dimensions.........................................................................................62
NH Series Dimensions........................................................................................84
EL Series Dimensions........................................................................................104

Bravo® Worm - Worm

Right Angle Worm Gear Reducers - Double Reduction Worm - Worm

Double Reducers
Introduction...................................................................................................... 122
Quick Selection................................................................................................ 130
Maximum Rating Tables.................................................................................. 132
Single-piece, alloy steel input Weights & Technical Information.................................................................... 137
worm shaft. High lead angle GR Series Dimensions...................................................................................... 142
worm is case-hardened, NH Series Dimensions..................................................................................... 160
ground and polished for EL Series Dimensions........................................................................................178
enhanced efficiency and noise
reduction. Right Angle Worm Gear Reducers - Double Reduction Helical - Worm
Introduction...................................................................................................... 194

Bravo® Helical - Worm

Quick Selection................................................................................................ 201

Double Reduction
Maximum Rating Tables.................................................................................. 203
Weights & Technical Information.................................................................... 209
GR Series Dimensions...................................................................................... 212
High capacity oil reservoir NH Series Dimensions..................................................................................... 230
reduces noise, aids heat EL Series Dimensions........................................................................................240
dissipation and lubricates
for life. Multiple venting Right Angle Worm Gear Reducers - WASHGUARD® and Stainless
options for multi-position
mounting. Factory filled with Introduction...................................................................................................... 256
premium Mobil Glygoyle 460 Maximum Rating Tables.................................................................................. 260
polyalkalene glycol (PAG)
lubricant. Ratio Multipliers & Modified Stock Reducers
Ratio Multipliers............................................................................................... 276

Bravo® Accessory Kits

Additional Capabilities..................................................................................... 283
Accessories....................................................................................................... 288
Accessories - WASHGUARD®......................................................................... 298

Bravo® Aluminum Right Angle Worm Gear Reducers - Single Reduction

Introduction...................................................................................................... 300
Maximum Rating Tables.................................................................................. 305
Weights & Technical Information.................................................................... 311
Dimensions....................................................................................................... 312

Bravo® Aluminum Right Angle Worm Gear Reducers -

Double Reduction Worm - Worm
Introduction...................................................................................................... 326

Gear Reducers
Helical - Inline
Maximum Rating Tables.................................................................................. 329
Weights & Technical Information.................................................................... 331
Robust output shaft of Dimensions....................................................................................................... 332
high strength steel alloy
for superior torque and Bravo® Aluminum Right Angle Worm Gear Reducers -
overhung load capacities. Double Reduction Helical - Worm
Introduction...................................................................................................... 344
Maximum Rating Tables.................................................................................. 347
Viton® premium quality, double lip seals** Weights & Technical Information.................................................................... 349
throughout —on micro-finished surfaces— Dimensions....................................................................................................... 350
mean extended life, resistance to high
temperature, abrasion and chemicals. Bravo® Aluminum Right Angle Worm Gear Reducers
Helical - Worm
Gear Reducers

Accessories & Additional Capabilities............................................................ 362

Technical Information....................................................................................... 367

Single output cover

design provides
precise centering
of gear for lower
noise levels and
higher overall gear
efficiencies. www.grovegear.com 15
 ELECTRA-GEAR
Worm Gear Reducers

Precision mounting surfaces and extra

Single Reduction

threaded bolt holes on top and bottom for

Aluminum Gear Reducers flexibility and to accept a wide range of stock

mounting accessories.

Built For Industrial Use High capacity oil reservoir

reduces noise, aids heat
dissipation and lubricates for
life. Multiple venting options
for multi-position mounting.
Worm - Worm Gear Reducers

O-rings on input and output Factory filled with premium

Oversized positively-retained covers eliminate gaskets, synthetic Mobil Glygoyle 460
Double Reduction

high speed input shaft bearing sealants and leaks. polyalkalene glycol (PAG)
for higher shock load capacity, lubricant.
shaft alignment and seal life. Ideal
for frequent starting and reversing
applications.

Single-piece, alloy steel

input worm shaft. High lead
angle worm is case-hardened,
Helical - Worm Gear Reducers

ground and polished for

enhanced efficiency and noise
Double Reduction

reduction.

DIN1705 (CuSn45Ni4) bronze alloy

provides maximum strength, lubricity
and superior life.

Tapered roller bearings on output

shaft for high overhung and thrust
WASHGUARD® Reducers

load capacities.
and GEAR+MOTOR™

Viton® premium quality, double lip seals

provide extended life and resistance to high
temperature, abrasion and chemicals. Only
non-rusting rubber O.D. seals used in all
exposed locations.

EL Series One piece 356T cast

aluminum housing to provide
strength and rigidity. Polished finish
also available.
Ratio Multipliers

EL Series Mounting dimensions same as

the original Electra-Gear product with an option
Additional Capabilities

Robust output shaft of to match the industry standard dimensions of

Accessories and

high strength steel alloy Grove Gear.

Single output cover design
for superior torque and provides precise centering of gear
overhung load capacities. for lower noise levels and higher GR and NH Series Mounting dimensions
overall gear efficiencies. Output are interchangeable with Baldor 900 series,
shaft comes out non-cover side Boston Gear, Browning Raider, Falk, Morse
as standard. Invader and other “industry standard”
reducers.

16 www.grovegear.com
ALL FEATURES SHOWN ARE SAME FOR ALL GR, NH AND
EL SERIES EXCEPT WHERE NOTED.
Series Comparison

Worm Gear Reducers

Single Reduction
Seal Guard** on quill-input styles
protects input seal from damage
during motor installation.

** Sizes 813 through 852 only

Cast aluminum NEMA C-input
with machined fits for precision
alignment of motors and bearings.
(EL Series)
Cast iron NEMA C-input flange

Worm - Worm Gear Reducers

with machined fits for precision • Grove Gear IRONMAN 800 Series
alignment of motors and bearings.

Double Reduction
(GR & NH Series) • Cast Iron Housing Construction
• M
 ounting dimensions are interchangeable with most industry
standard reducers
• Designed with industry leading premium features as standard
Push-off holes drilled • C
 ombines the premium features of the LEESON IRONMAN
and tapped into flange
with the industry’s broadest product offering of the Grove
for quick motor removal
on quill input styles Gear Flexaline
(56 & 140TC frames). • GEAR+MOTOR™ Available

Helical - Worm Gear Reducers

Double Reduction
Premium Grade 5
zinc-plated bolts
used throughout.

WASHGUARD® Reducers
and GEAR+MOTOR™
• Grove Gear IRONMAN Narrow Housing 800 Series
• Cast Iron Housing Construction
• Designed with industry leading premium features as standard
• R
 eplacement for Grove Gear OE Series and original Alling
Lander gear reducers
• C
 ompact housing design to fit where other reducer brands
cannot
• GEAR+MOTOR™ Available

Ratio Multipliers

ELECTRA-GEAR
Additional Capabilities
Accessories and

• Electra-Gear 800 Series

• Aluminum Housing Construction
• L ightweight design with all the premium features of the GR
and NH series as standard
• Replacement to original Electra-Gear reducers
• GEAR+MOTOR™ Available

www.grovegear.com 17
 Interchange
ALUMINUM Guide
CAST IRON
EL SERIES GR SERIES
Single Reduction
Worm Gear Reducers
Single Reduction

ALUMINUM CAST IRON CAST IRON ALUMINUM Replaces Original

CAST IRON Replaces Original
EL SERIES GR SERIES NH SERIES EL SERIES GR SERIES ELECTRA-GEAR
Reducer Style OE Series Reducer Style Reducer Style
B U M
BM & BMQ UFC & UF MC & MSC
CAST IRON CAST IRON
NH SERIES BH N/A ML
NH SERIES
Worm - Worm Gear Reducers

Style BMQ BM & BMQH N/A MLC & MLSC

T & U Z & UB A
Double Reduction

TM & TMQ ZFC & ZF AC & ASC

TH N/A AL
TM & TMQH N/A ALC & ALSC
UM & UMQ UBFC & UBF NEW
Style TMQ
J J JB
JM & JMQ JFC & JF JBC & JBSC
VL & VH SL & SH B
VLM & VLMQ SLFC & SLF BC & BSC
Helical - Worm Gear Reducers

VHM SHFC N/A

VHMQ SHF N/A
Double Reduction

Style JMQ
F K & V N/A
FM & FMQ KFC & KF / VFC & VF N/A
C P N/A
CM & CMQ PFC & PF N/A
FE E N/A
Style FMQ
FEM & FEMQ EFC & EF N/A
H Y MH_ & H_
HM & HMQ YFC & YF MH_C/ MH_SC & H_C/H_SC
JH N/A JBH_
WASHGUARD® Reducers
and GEAR+MOTOR™

JHM & JHMQ N/A JBH_C & JBH_SC

FH M RH_
Style CMQ FHM & FHMQ MFC & MF RH_C & H_C/H_SC & RH_SC
FR N/A New
FRM & FRMQ N/A New
FL N/A RL
FLM & FLMQ N/A RLC & RLSC
BL (Torque Limiter Reducer) UL N/A
Style FEMQ BLM & BLMQ (Torque Limiter Reducer) ULFC & ULF N/A
ABC N/A ABC (contact factory)
Accessory
Ratio Multipliers

Horizontal Base Kit (T & U) Horizontal Base Kit (Z & UB) Horizontal Base Kit (AK Kit #’s)
Vert. Output Shaft Base Kit (VL & VH) Vert. Output Shaft Base Kit (SL & SH) Vert. Output Shaft Base Kit (BK Kit #’s)
Style HMQ Vertical Input Shaft Base Kit (J) Vert. Input Shaft Base Kit (J) Vert. Input Shaft Base Kit (JBK Kit #’s)
Cast Iron Output Flange (F) Cast Iron Output Flange (K & V) Cast Iron Output Flange (Square)
ABC Base Kit N/A ABC
Cast Iron Output Flange for
N/A Cast Iron Output Flange (Round)
Solid Output Shaft Styles (FR)
Coupling Input ”C” Flange Kit – Single Red.: C-Flange Mounting Kit N/A
Style JHMQ Coupling Input ”C” Flange Kit – Double Red.: C-Flange Mounting Kit N/A
Additional Capabilities

Hollow Shaft Tie Rod Kit Hollow Shaft Tie Rod Kit Hollow Shaft Tie Rod Kit
Accessories and

Hollow Shaft Torque Arm Bracket Hollow Shaft Torque Arm Bracket
Hollow Shaft Torque Arm Bracket
(TAK Kit #’s)
H Confirm required output shaft length
: Convert Style B to BM using coupling input kit
Style VLHMQ

SEE PAGE 123 FOR DOUBLE REDUCTION

18 www.grovegear.com
 Model Number System

Worm Gear Reducers

GR • NH • EL Series

Single Reduction
800 Series Gear Reducer Model Number Nomenclature
All new stock and custom 800 Series Grove Gear and Electra-Gear worm gear reducers are TYPICAL NAMEPLATE
identified by a model number. The model number appears on the nameplate and describes (Electra-Gear shown)
pertinent features of the reducer. An example follows, along with a listing of the various
letters and positions used. RATING @ 1750 RPM INPUT
AGMA CLASS 1 SERVICE
MOBIL SHC 634 GEAR OIL

NOTE: All reducers also have a catalog number—for example EL8130001 and GR8130001. ELECTRA-GEAR INPUT HP
1.49
Reducers and renewal parts should be ordered by catalog number. If a stock reducer has OUT TORQ
IN-LBS 571
been Factory modified by the addition of an optional base for example, the modification RATIO :1
15
number T818EL is stamped in the blank column of the nameplate. Accessories that are field EL8180112.00 DATE
F09

Worm - Worm Gear Reducers

CATALOG NO. CODE

installed will not be noted on the nameplate. MODEL NO. EL-BMQ818-15-L-56 MOD

Catalog numbers 3000 and higher (for example, GR8133000 and NH8133000) are

Double Reduction
WASHGUARD® reducers for washdown service.
Catalog numbers 5000 and higher (for example, GR8135000 and EL8135000) are custom
reducers manufactured for a specific application. The machinery or equipment manufacturer
should be contacted for replacement reducers. Renewal parts can be ordered by catalog
number.
Output
Series Code Style Size Ratio Output Shaft Orientation Motor Flange Bore Code

Hollow Shaft

Helical - Worm Gear Reducers

SOLID OUTPUT SHAFT L – Left-hand Output Shaft* Only
See Selection Tables
BMQ – Motorized, Quill Input on pages 32-58, for R – Right-hand Output Shaft* See bottom

Double Reduction
BM – Motorized, Flexible all available ratios. right hand
D – Double Output Shaft
Coupling Input pages of
H – Hollow Output Shaft Max Ratings
B – Non-Flanged
* Viewed from drive end of reducer. Tables starting
on page 37.
HOLLOW OUTPUT SHAFT
HMQ – Motorized, Quill Input
HM – Motorized, Flexible
800 SERIES Input For
Coupling Input
CENTER DISTANCES Code Input Type
H – Non-Flanged
Center Distance Single Input Dual Input
Size (Inches) blank A non-motorized
WASHGUARD STYLES

WASHGUARD® Reducers
48** 48A 48CZ

NEMA Input
813 1.33

and GEAR+MOTOR™
W prefix; i.e. WBMQ denotes
815** 1.54 56 56A 56C
WASHDOWN Reducer
818 1.75 140 140A 143-5TC
S prefix; i.e. SHMQ denotes
821 2.06 180 180A 182-4TC
All-Stainless Steel Reducer 210 210A 213-5TC
824 2.38
826 2.62 250 250A 254-6TC
830 3.00 63 D63D B5
832 3.25 71 D71D B5

IEC Input
842 4.25 80 Contact D80D B5
GR - Grove Gear IRONMAN Cast Iron Reducers 852 5.25
90 Factory D90D B5
NH - Grove Gear IRONMAN Narrow 110 D100LD/D112MD B5
860 6.00
Housing Cast Iron Reducers 132 D132D
870* 7.00
EL - Electra-Gear Aluminum Reducers ** Not available in EL Series
880* 8.00
GRG - Grove Gear Flexaline Interchange
(Sizes 821, 826, 832) 8100* 10.00

Ratio Multipliers
* GR Series only
GRL - Leeson IRONMAN Interchange ** Not available in EL Series
(Sizes 821, 826, 832)

Sample Model Numbers

Solid Output Shaft - GR Series Hollow Output Shaft - EL Series
Cast iron, single reduction, 2.38” reducer with 56C motorized quill input, Aluminum, single reduction, 1.75” reducer with 56C motorized quill input,
left-hand output shaft, 30:1 ratio. 1.00” hollow output bore, 10:1 ratio.
Additional Capabilities
Accessories and

GR - BMQ 824 - 30 - L - 56 EL - HMQ 818 - 10 - H - 56 - 16

Series Style Size Ratio Shaft Input Series Style Size Ratio Shaft Input Output Bore
Orientation Type Orientation
Type Code

www.grovegear.com 19
 Cast Iron
Solid Shaft Output Styles
Worm Gear Reducers
Single Reduction

Stock Styles Modified Stock Styles

Using off-the-shelf accessories, stock styles BMQ, BM and B can be field or
Factory modified into a wide range of styles. See pages 296 for details.

Horizontal Base Horizontal Base Horizontal Base Vertical

Worm Over Worm Under Worm Center Input Shaft
Worm - Worm Gear Reducers

Style BMQ Style TMQ Style UMQ* Style RMQ Style JMQ
Double Reduction

QUILL INPUT
MOTORIZED
C-FLANGE
Helical - Worm Gear Reducers
Double Reduction

Ratings Pages: 32-58 Ratings Pages: 32-58 Ratings Pages: 32-58 Ratings Pages: 32-58 Ratings Pages: 32-58

Dimension Pages: Dimension Pages: Dimension Pages: Dimension Pages: Dimension Pages:
GR Series 62-63 GR Series 64-65 GR Series 66-67 GR Series 72-73 GR Series 68-69
NH Series 84-85 NH Series 86-87 NH Series 88-89 NH Series 90-91

Style BM Style TM Style UM* Style RM Style JM

MOTORIZED C-FLANGE
FLEXIBLE COUPLING
WASHGUARD® Reducers
and GEAR+MOTOR™

INPUT

Ratings Pages: 32-58 Ratings Pages: 32-58 Ratings Pages: 32-58 Ratings Pages: 32-58 Ratings Pages: 32-58

Dimension Pages: Dimension Pages: Dimension Pages: Dimension Pages: Dimension Pages:
GR Series 62-63 GR Series 64-65 GR Series 66-67 GR Series 72-73 GR Series 68-69
NH Series 84-85 NH Series 86-87 NH Series 88-89 NH Series 90-91
Ratio Multipliers

Style B Style T Style U* Style R Style J

NON-FLANGED
INPUT
Additional Capabilities
Accessories and

Ratings Pages: 32-58 Ratings Pages: 32-58 Ratings Pages: 32-58 Ratings Pages: 32-58 Ratings Pages: 32-58

Dimension Pages: Dimension Pages: Dimension Pages: Dimension Pages: Dimension Pages:
GR Series 62-63 GR Series 64-65 GR Series 66-67 GR Series 72-73 GR Series 68-69
NH Series 84-85 NH Series 86-87 NH Series 88-89 NH Series 90-91

Not a recommended mounting style. Contact Factory for selection assistance. Additional accessories, options and assembly services are available,
* contact Factory for details.

20 www.grovegear.com
 Cast Iron
Solid Shaft Output Styles

Worm Gear Reducers

Single Reduction
Vertical Vertical Flange “C” Flange Extended Flange
Output Shaft Output Shaft Mounted Mounted Mounted
Low Base High Base Output Shaft Output Shaft Output Shaft

Worm - Worm Gear Reducers

Style VLMQ** Style VHMQ** Style FMQ Style CMQ Style FEMQ

Double Reduction
Helical - Worm Gear Reducers
Double Reduction
Ratings Pages: 32-58 Ratings Pages: 32-58 Ratings Pages: 32-58 Ratings Pages: 32-58 Ratings Pages: 32-58

Dimension Pages: Dimension Pages: Dimension Pages: Dimension Pages: Dimension Pages:
GR Series 70-71 GR Series 70-71 GR Series 74-75 GR Series 76-77 GR Series 82-83
NH Series 92-93 NH Series 92-93 NH Series 94-95 NH Series 100-101

Style VLM ** Style VHM** Style FM Style CM Style FEM

WASHGUARD® Reducers
and GEAR+MOTOR™
Ratings Pages: 32-58 Ratings Pages: 32-58 Ratings Pages: 32-58 Ratings Pages: 32-58 Ratings Pages: 32-58

Dimension Pages: Dimension Pages: Dimension Pages: Dimension Pages: GR Dimension Pages:
GR Series 70-71 GR Series 70-71 GR Series 74-75 Series 76-77 GR Series 82-83
NH Series 92-93 NH Series 92-93 NH Series 94-95 NH Series 100-101

Ratio Multipliers
Style VL ** Style VH ** Style F Style C Style FE
Additional Capabilities
Accessories and

Ratings Pages: 32-58 Ratings Pages: 32-58 Ratings Pages: 32-58 Ratings Pages: 32-58 Ratings Pages: 32-58

Dimension Pages: Dimension Pages: Dimension Pages: Dimension Pages: Dimension Pages:
GR Series 70-71 GR Series 70-71 GR Series 74-75 GR Series 76-77 GR Series 82-83
NH Series 92-93 NH Series 92-93 NH Series 94-95 NH Series 100-101

SPECIFY SHAFT UP OR DOWN FOR THESE

** STYLES.

www.grovegear.com 21
 Cast Iron
Hollow Shaft Output Styles
Worm Gear Reducers
Single Reduction

Stock Styles Modified Stock Styles

Using off-the-shelf accessories, stock styles HMQ, HM and H can be field
or Factory modified into a wide range of styles. See pages 286-287 for
details.

Vertical
Worm - Worm Gear Reducers

Input Shaft
Double Reduction

Style HMQ Style JHMQ

MOTORIZED
C-FLANGE
QUILL
INPUT
Helical - Worm Gear Reducers
Double Reduction

Ratings Pages: 32-58 Ratings Pages: 32-58

Dimension Pages: Dimension Pages:

GR Series 78-79 Contact Factory
NH Series 96-97

Style HM Style JHM

WASHGUARD® Reducers

MOTORIZED
and GEAR+MOTOR™

COUPLING
C-FLANGE
FLEXIBLE

INPUT

Ratings Pages: 32-58 Ratings Pages: 32-58

Dimension Pages: Dimension Pages:

GR Series 78-79 Contact Factory
Ratio Multipliers

NH Series 96-97

Style H Style JH
FLANGED
INPUT
NON-
Additional Capabilities
Accessories and

Ratings Pages: 32-58 Ratings Pages: 32-58

Dimension Pages: Dimension Pages:

GR Series 78-79 Contact Factory
NH Series 96-97
Additional accessories, options and assembly services are available,
Contact Factory for details.
22 www.grovegear.com
 Cast Iron
Hollow Shaft Output Styles

Worm Gear Reducers

Single Reduction
Vertical Vertical Flange
Output Shaft Output Shaft Mounted

Worm - Worm Gear Reducers

Low Base High Base Output Shaft

Double Reduction
Style VLHMQ Style VHHMQ Style FHMQ

Helical - Worm Gear Reducers

Double Reduction
Ratings Pages: 32-58 Ratings Pages: 32-58 Ratings Pages: 32-58

Dimension Pages: Dimension Pages: Dimension Pages:

Contact Factory Contact Factory GR Series 80-81
NH Series 98-99

Style VLHM Style VHHM Style FHM

WASHGUARD® Reducers
and GEAR+MOTOR™
Ratings Pages: 32-58 Ratings Pages: 32-58 Ratings Pages: 32-58

Dimension Pages: Dimension Pages: Dimension Pages:

Contact Factory Contact Factory GR Series 80-81

Ratio Multipliers
NH Series 98-99

Style VLH Style VHH Style FH Additional Capabilities

Accessories and

Ratings Pages: 32-58 Ratings Pages: 32-58 Ratings Pages: 32-58

Dimension Pages: Dimension Pages: Dimension Pages:

Contact Factory Contact Factory GR Series 80-81
NH Series 98-99

www.grovegear.com 23
 ELECTRA-GEAR
Aluminum
Worm Gear Reducers
Single Reduction

Solid Shaft Output Styles

Stock Styles Modified Stock Styles
Using off-the-shelf accessories, stock styles BMQ, BM and B can be field or
Factory modified into a wide range of styles. See pages 296 for details.

Horizontal Base Horizontal Base

Worm Over Worm Under
Worm - Worm Gear Reducers

Style BMQ Style TMQ Style UMQ*

Double Reduction

QUILL INPUT
MOTORIZED
C-FLANGE
Helical - Worm Gear Reducers
Double Reduction

Ratings Pages: 32-58 Ratings Pages: 32-58 Ratings Pages: 32-58

Dimension Pages: Dimension Pages: Dimension Pages:

EL Series 104-105 EL Series 106-107 EL Series 108-109

Style BM Style TM Style UM*

MOTORIZED

COUPLING
C-FLANGE
FLEXIBLE
WASHGUARD® Reducers
and GEAR+MOTOR™

INPUT

Ratings Pages: 32-58 Ratings Pages: 32-58 Ratings Pages: 32-58

Dimension Pages: Dimension Pages: Dimension Pages:

EL Series 104-105 EL Series 106-107 EL Series 108-109
Ratio Multipliers

Style B Style T Style U*

FLANGED
INPUT
NON-
Additional Capabilities
Accessories and

Ratings Pages: 32-58 Ratings Pages: 32-58 Ratings Pages: 32-58

Dimension Pages: Dimension Pages: Dimension Pages:

EL Series 104-105 EL Series 106-107 EL Series 108-109

Not a recommended mounting style. Additional accessories, options and assembly services are available,
* Contact Factory for selection assistance.
Contact Factory for details.

24 www.grovegear.com
 ELECTRA-GEAR
Aluminum

Worm Gear Reducers

Single Reduction
Solid Shaft Output Styles

Vertical Flange
Output Shaft Mounted
Vertical Low Base Output Shaft

Worm - Worm Gear Reducers

Input Shaft

Style JMQ** Style VLMQ**

Double Reduction
Style FRMQ

Helical - Worm Gear Reducers

Double Reduction
Ratings Pages: 32-58 Ratings Pages: 32-58 Ratings Pages: 32-58

Dimension Pages: Dimension Pages: Dimension Pages:

EL Series 110-111 EL Series 112-113 EL Series 114-115

Style JM** Style VLM ** Style FRM

WASHGUARD® Reducers
and GEAR+MOTOR™
Ratings Pages: 32-58 Ratings Pages: 32-58 Ratings Pages: 32-58

Dimension Pages: Dimension Pages: Dimension Pages:

EL Series 110-111 EL Series 112-113 EL Series 114-115

Style J ** Style VL ** Style FR Ratio Multipliers

Additional Capabilities
Accessories and

Ratings Pages: 32-58 Ratings Pages: 32-58 Ratings Pages: 32-58

Dimension Pages: Dimension Pages: Dimension Pages:

EL Series 110-111 EL Series 112-113 EL Series 114-115

SPECIFY SHAFT UP OR DOWN FOR THESE STYLES.

**

www.grovegear.com 25
 ELECTRA-GEAR
Aluminum
Worm Gear Reducers
Single Reduction

Hollow Shaft Output Styles

Stock Styles Modified Stock Styles
Using off-the-shelf accessories, stock styles HMQ, HM and H can be
field or Factory modified into a wide range of styles. See pages 296
for details.
Vertical
Input Shaft
Worm - Worm Gear Reducers

Style HMQ Style JHMQ

Double Reduction

MOTORIZED
C-FLANGE
QUILL
INPUT
Helical - Worm Gear Reducers
Double Reduction

Ratings Pages: 32-58 Ratings Pages: 32-58

Dimension Pages: Dimension Pages:

EL Series 116-117 Contact Factory

Style HM Style JHM

MOTORIZED

COUPLING
C-FLANGE
WASHGUARD® Reducers

FLEXIBLE
and GEAR+MOTOR™

INPUT

Ratings Pages: 32-58 Ratings Pages: 32-58

Dimension Pages: Dimension Pages:

EL Series 116-117 Contact Factory
Ratio Multipliers

Style H Style JH
FLANGE
INPUT
NON-
Additional Capabilities
Accessories and

Ratings Pages: 32-58 Ratings Pages: 32-58

Dimension Pages: Dimension Pages:

EL Series 116-117 Contact Factory
Additional accessories, options and assembly services are available,
Contact Factory for details.
26 www.grovegear.com
 ELECTRA-GEAR
Aluminum

Worm Gear Reducers

Single Reduction
Hollow Shaft Output Styles

Vertical Flange
Output Shaft Mounted
Low Base Output Shaft

Worm - Worm Gear Reducers

Style VLHMQ Style FHMQ

Double Reduction
Helical - Worm Gear Reducers
Double Reduction
Ratings Pages: 32-58 Ratings Pages: 32-58

Dimension Pages: Dimension Pages:

Contact Factory EL Series 118-119

Style VLHM Style FHM

WASHGUARD® Reducers
and GEAR+MOTOR™
Ratings Pages: 32-58 Ratings Pages: 32-58

Dimension Pages: Dimension Pages:

Contact Factory EL Series 118-119

Style VLH Style FH Ratio Multipliers

Additional Capabilities
Accessories and

Ratings Pages: 32-58 Ratings Pages: 32-58

Dimension Pages: Dimension Pages:

Contact Factory EL Series 118-119

Additional accessories, options and assembly services are available,

Contact Factory for details.
www.grovegear.com 27
 Quick Selections
Worm Gear Reducers
Single Reduction

How to Use
Based on required output RPM and input motor horsepower, read across
chart for the appropriate reducer size. As a rule of thumb, use 1.00 service
factor chart for applications having uniform loads with up to 10 hours service
duration per day. Use 1.25 service factor chart for longer service or shock
Worm - Worm Gear Reducers

loading. These charts are to be considered as guides only. Refer to page

Double Reduction

642 or Contact Factory with specific application information.

1.0 Service Factor

Nominal Output Input Horsepower @ 1750 RPM
Ratio♠ RPM 1/6 1/4 1/3 1/2 3/4 1 1-1/2 2 3 5 7-1/2 10 15 20 25 30 40 50 60 75 100
5 350 813 813 813 813 813 813 815 818 821 824 830* 832** 842 852 852 852 860 870 880 8100
8100
7.5 233 813 813 813 813 813 813 818 821 824 826 832 842 842 852 852 860 870 880 8100
8100
10 175 813 813 813 813 813 815 818 821 824 830 832** 842 842 852 860 870 880 8100 8100
15 117 813 813 813 813 815 815 821 824 826 832 842 842 852 870 870 880 8100
8100
20 88 813 813 813 813 815 818 821 824 826 832** 842 852 860 870 880 8100 8100
Helical - Worm Gear Reducers

25 70 813 813 813 815 815 821 824 826 830* 842 842 852 870 880 8100 8100
30 58 813 813 813 815 821 821 824 826 832 842 852 852 880 8100 8100
Double Reduction

40 44 813 813 813 815 821 824 826 830* 842 842 852 870 8100 8100
50 35 813 813 815 818 821 824 830 832** 842 852 870 880 8100
60 29 813 813 815 821 824 826 830* 832** 842 852 880 8100
70 25 N/A N/A N/A N/A N/A N/A N/A N/A N/A 870 880 8100
80 22 815 821 824 826 830 832 842 852 860
100 18 821 824 826 830 842 842 852 852
WASHGUARD® Reducers
and GEAR+MOTOR™

1.25 Service Factor

Nominal Output Input Horsepower @ 1750 RPM
Ratio♠ RPM 1/6 1/4 1/3 1/2 3/4 1 1-1/2 2 3 5 7-1/2 10 15 20 25 30 40 50 60 75
5 350 813 813 813 813 813 813 815 821 824 826 832** 842 852 852 852 870 870 880 8100 8100
7.5 233 813 813 813 813 813 815 818 821 824 830* 842 842 852 852 870 870 880 8100 8100
10 175 813 813 813 813 815 815 821 824 826 832 842 842 852 860 870 880 8100 8100
15 117 813 813 813 813 815 818 821 824 830 842 842 852 860 870 880 8100
8100
20 88 813 813 813 815 818 821 824 826 830* 842 842 852 870 880 8100
8100
25 70 813 813 813 815 821 821 824 826 832** 842 852 860 880 8100 8100
30 58 813 813 815 815 821 824 826 830* 842 842 852 870 8100 8100
40 44 813 813 815 821 824 824 830* 832** 842 852 870 880 8100
50 35 813 815 815 821 824 826 830* 842 842 852 880 8100
Ratio Multipliers

60 29 813 815 818 821 824 830 832 842 852 870 8100 8100
70 25 N/A N/A N/A N/A N/A N/A N/A N/A 870 880 8100
80 22 815 821 824 830 832 842 852 852
100 18 815 824 830 832 842 852 852 860
Note: This chart is meant as a guide for reducer selections at specific motor horsepowers.
Actual service factor may be greater than indicated. For actual service factors and maximum worm reducer ratings, refer to pages 32-58.
♠ Refer to page 30 for exact ratio of single reduction worm gear reducers.
* Size 832 must be used for NH Series for this selection.
** Size 842 must be used for NH Series for this selection.
indicates a selection where a smaller reducer (1 case size) can be used with redesigned product due to rating increase.
indicates a selection where a smaller reducer (2 case sizes) can be used with redesigned product due to rating increase.
Additional Capabilities
Accessories and

Refer To Pages 522-581 for K Series Helical-Bevel

right angle gear reducers for higher horsepower
selections not covered here

28 www.grovegear.com
 Quick Selections

Worm Gear Reducers

Single Reduction
1.50 Service Factor
Nominal Output I nput Horsepower @ 1750 RPM
Ratio♠ RPM 1/6 1/4 1/3 1/2 3/4 1 1-1/2 2 3 5 7-1/2 10 15 20 25 30 40 50 60
5 350 813 813 813 813 813 815 818 821 824 830* 832** 842 852 852 870 870 880 8100 8100
7.5 233 813 813 813 813 815 815 821 824 826 832 842 842 852 860 870 880 8100
8100
10 175 813 813 813 813 815 818 821 824 826 832** 842 852 852 870 880 8100 8100

Worm - Worm Gear Reducers

15 117 813 813 813 815 818 821 824 826 830* 842 852 852 870 880 8100 8100
20 88 813 813 813 815 821 821 824 826 832** 842 852 860 880 8100 8100
25 70 813 813 815 815 821 824 826 830* 842 842 852 870 8100 8100

Double Reduction
30 58 813 813 815 821 821 824 830 832 842 852 870 880 8100
40 44 813 815 815 821 824 826 830* 832** 842 852 880 8100
50 35 813 815 818 821 824 830 832** 842 852 870 880 8100
60 29 813 815 821 824 826 830* 842 842 852 880 8100
70 25 N/A N/A N/A N/A N/A N/A N/A N/A 870 880 8100
80 22 821 824 826 830 842 842 852 860
100 18 824 826 830 842 842 852 860

1.75 Service Factor

Helical - Worm Gear Reducers

Nominal Output I nput Horsepower @ 1750 RPM

Double Reduction
Ratio♠ RPM 1/6 1/4 1/3 1/2 3/4 1 1-1/2 2 3 5 7-1/2 10 15 20 25 30 40 50 60
5 350 813 813 813 813 815 815 818 821 824 830* 842 842 852 860 870 880 8100 8100 8100
7.5 233 813 813 813 813 815 818 821 824 830 832** 842 852 852 870 880 880 8100
10 175 813 813 813 815 818 821 824 824 830 842 842 852 870 870 880 8100
15 117 813 813 813 815 821 821 824 826 832 842 852 852 870 8100 8100
20 88 813 813 815 815 821 824 826 830* 842 842 852 870 8100 8100
25 70 813 813 815 818 821 824 830 832 842 852 870 880 8100
30 58 813 815 815 821 824 826 830* 832** 842 852 870 880 8100
40 44 813 815 818 821 824 830 832** 842 842 860 880 8100
50 35 813 815 821 824 826 830* 842 842 852 870 8100 8100
60 29 815 818 821 824 830* 832** 842 842 852 880 8100
70 25 N/A N/A N/A N/A N/A N/A N/A N/A 870 8100

WASHGUARD® Reducers
80 22 821 824 826 830 842 842 852 860

and GEAR+MOTOR™
100 18 824 830 830 842 852 852

2.00 Service Factor

Nominal Output Input Horsepower @ 1750 RPM
Ratio♠ RPM 1/6 1/4 1/3 1/2 3/4 1 1-1/2 2 3 5 7-1/2 10 15 20 25 30 40 50
5 350 813 813 813 813 815 818 821 824 826 832** 842 852 852 870 870 880 8100 8100
7.5 233 813 813 813 813 815 821 824 824 830 842 842 852 860 870 880 8100 8100
10 175 813 813 813 815 818 821 824 826 830* 842 852 852 870 880 8100 8100
15 117 813 813 815 815 821 824 826 830 832** 842 852 870 880 8100 8100
20 88 813 813 815 818 821 824 826 832 842 852 860 880 8100 8100
25 70 813 815 815 821 824 824 830* 832** 842 852 870 880 8100

Ratio Multipliers
30 58 813 815 818 821 824 826 832 842 842 852 880 8100
40 44 813 815 821 824 826 830* 842 842 852 870 8100 8100
50 35 815 818 821 824 830 832** 842 842 852 880 8100
60 29 815 821 821 826 830* 832** 842 852 860 8100
70 25 N/A N/A N/A N/A N/A N/A 870 870 880 8100
80 22 824 826 830 832 842 852 860
100 18 826 830 832 842 852 852
Note: This chart is meant as a guide for reducer selections at specific motor horsepowers.
Actual service factor may be greater than indicated. For actual service factors and maximum worm reducer ratings, refer to pages 32-58.
♠ Refer to page 30 for exact ratio of single reduction worm gear reducers.
* Size 832 must be used for NH Series for this selection.
** Size 842 must be used for NH Series for this selection.
Additional Capabilities

indicates a selection where a smaller reducer (1 case size) can be used with redesigned product due to rating increase.
Accessories and

indicates a selection where a smaller reducer (2 case sizes) can be used with redesigned product due to rating increase.

Refer To Pages 522-581 for K Series Helical-Bevel

right angle gear reducers for higher horsepower
selections not covered here

www.grovegear.com 29
 Exact Ratios
Worm Gear Reducers
Single Reduction

Unit 5 7.5 10 15 20 25 30 40 50 60 70 80 100

813 X X X X X X X X X X NA X X
815 X X X X X X X X X X NA X X
818 X X X X X X X X X X NA X X
821 X X X X X X X X X X NA X X
824 X X X X X X X X X X NA X X
826 5 1/6 X X X X X X X X X NA X X
Worm - Worm Gear Reducers

830 X X X X X X X X X X NA X X
832 5 1/6 X X X X X X X X X NA X X
Double Reduction

842 5 1/6 X X X X X X X X X NA X X
852 5 1/8 X X X X X X X X X NA X X
860 X X X X X X X X X X NA X X
870 5 1/8 7 2/5 9 3/4 14 2/3 20 1/2 24 1/2 29 1/2 X X X X NA NA
880 5 1/8 7 2/5 9 3/4 14 2/3 20 1/2 24 1/2 29 1/2 X X X X NA NA
8100 5 1/8 7 1/3 9 3/4 14 2/3 20 1/2 24 1/2 29 1/2 X X X X NA NA
Helical - Worm Gear Reducers

HOLLOW SHAFT BORE SIZES (Inches)*

Fraction Decimal Output
Double Reduction

813 815 818 821 824 826 830 832 842 852 860 870 880 8100 Keyway**
Size Size Bore Code

5/8 0.625 10 3/16 x 3/32

11/16 0.688 11 3/16 x 3/32

3/4 0.750 12 3/16 x 3/32

7/8 0.875 14 3/16 x 3/32
1 1.000 16 1/4 x 1/8

1-1/8 1.125 18 1/4 x 1/8

1-3/16 1.188 19 1/4 x 1/8
WASHGUARD® Reducers
and GEAR+MOTOR™

1-1/4 1.250 20 1/4 x 1/8

1-7/16 1.438 23 3/8 x 3/16

1-1/2 1.500 24 3/8 x 3/16

1-5/8 1.625 26 3/8 x 3/16

1-11/16 1.688 27 3/8 x 3/16

1-3/4 1.750 28 3/8 x 3/16

1-7/8 1.875 30 1/2 x 1/4

1-15/16 1.938 31 1/2 x 1/4
2 2.000 32 1/2 x 1/4

2- 3/16 2.188 35 1/2 x 1/4
Ratio Multipliers

2-1/4 2.250 36 1/2 x 1/4

2-7/16 2.438 39 5/8 x 5/16

2-1/2 2.500 40 5/8 x 5/16

2-11/16 2.688 43 5/8 x 5/16

2-15/16 2.938 47 3/4 x 3/8
3 3.000 48 3/4 x 3/8

3-3/16 3.188 51 3/4 x 3/8

3-7/16 3.438 55 7/8 x 7/16
Additional Capabilities

3-15/16 3.938 63 1 x 1/2
Accessories and

4-3/16 4.188 67 1 x 1/2

4-7/16 4.438 71 1 x 1/2

4-15/16 4.938 79 1-1/4 x 5/8

5-7/16 5.438 87 1-1/4 x 5/8
Stock Bore Sizes.
*Other bore sizes are available. Contact Factory for sizes and availability.
** Dimensions refer to customer driven shaft.
NOTE: S  pecify the required bore size when ordering. The suffix “XX” can be substituted with the bore code from table above.
30 www.grovegear.com