120W Single Output Industrial DIN RAIL Power Supply DR-120 series

■ Features :
AC input range selectable by switch
Protections: Short circuit / Overload / Over voltage / Over temperature
Cooling by free air convection
Can be installed on DIN rail TS-35/7.5 or 15
UL 508(industrial control equipment)approved
LED indicator for power on
100% full load burn-in test
Fixed switching frequency at 55KHz
3 years warranty
Bauar t gepruft
Sicherheit
egel ma ge
od o s
be wac g

SPECIFICATION
www. tuv.com
ID 2000000000

MODEL DR-120-12 DR-120-24 DR-120-48

DC VOLTAGE 12V 24V 48V
RATED CURRENT 10A 5A 2.5A
CURRENT RANGE 0 ~ 10A 0 ~ 5A 0 ~ 2.5A
RATED POWER 120W 120W 120W
RIPPLE & NOISE (max.) Note.2 80mVp-p 80mVp-p 100mVp-p
OUTPUT VOLTAGE ADJ. RANGE 12 ~ 14V 24 ~ 28V 48 ~ 53V
VOLTAGE TOLERANCE Note.3 ±2.0% ±1.0% ±1.0%
LINE REGULATION ±0.5% ±0.5% ±0.5%
NR

LOAD REGULATION ±1.0% ±1.0% ±1.0%

SETUP, RISE TIME 500ms, 70ms/230VAC 500ms, 70ms/115VAC at full load
HOLD UP TIME (Typ.) 36ms/230VAC 32ms/115VAC at full load
VOLTAGE RANGE 88 ~ 132VAC/176 ~ 264VAC by switch 248 ~ 370VDC
FREQUENCY RANGE 47 ~ 63Hz
EFFICIENCY (Typ.) 80% 84% 85%
ND

INPUT
AC CURRENT (Typ.) 2.6A/115VAC 1.6A/230VAC
INRUSH CURRENT (Typ.) COLD START 20A/115VAC 40A/230VAC
LEAKAGE CURRENT <3.5mA / 240VAC
105 ~ 150% rated output power
OVERLOAD
Protection type : Constant current limiting, recovers automatically after fault condition is removed
15 ~ 16.5V 29 ~ 33V 58 ~ 65V
PROTECTION OVER VOLTAGE
Protection type : Shut down o/p voltage, re-power on to recover
85℃±5℃ (TSW1) 90℃±5℃(TSW1) 90℃±5℃(TSW1)
OVER TEMPERATURE
Protection type : Shut down o/p voltage, recovers automatically after temperature goes down
WORKING TEMP. -10 ~ +60℃ (Refer to "Derating Curve")
WORKING HUMIDITY 20 ~ 90% RH non-condensing
ENVIRONMENT STORAGE TEMP., HUMIDITY -20 ~ +85℃, 10 ~ 95% RH
TEMP. COEFFICIENT ±0.03%/℃ (0 ~ 50℃)
VIBRATION 10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes; Mounting: Compliance to IEC60068-2-6
SAFETY STANDARDS UL508, UL60950-1, TUV EN60950-1, EAC TP TC 004 approved
SAFETY & WITHSTAND VOLTAGE I/P-O/P:3KVAC I/P-FG:2.0KVAC O/P-FG:0.5KVAC
EMC ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25℃/ 70% RH
(Note 4) EMC EMISSION Compliance to EN55011,EN55032 (CISPR32) Class B, EN61000-3-2,-3, EAC TP TC 020
EMC IMMUNITY Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, EN61000-6-2 (EN50082-2), heavy industry level, criteria A, EAC TP TC 020
MTBF 432.1Khrs min. MIL-HDBK-217F (25℃)
OTHERS DIMENSION 65.5*125.2*100mm (W*H*D)
PACKING 0.79Kg; 20pcs/16.5Kg/1.29CUFT
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25℃ of ambient temperature.
NOTE
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
EMC directives.
5. The ambient temperature derating of 3.5℃/1000m with fanless models and of 5℃/1000m with fan models for operating altitude higher than 2000m(6500ft).

File Name:DR-120-SPEC 2018-01-12

 120W Single Output Industrial DIN RAIL Power Supply DR-120 series

Mechanical Specification Case No. 921A Unit:mm

100
125.2
+V ADJ.

115VAC

230VAC
TB1 TB2
1 1
2
65.5

2
3 3
4
LED

Terminal Pin No. Assignment (TB1)

Pin No. Assignment
1 FG
35

2 AC/N
3 AC/L
NR

ADMISSIBLE DIN-RAIL: TS35/7.5 OR TS35/15

Terminal Pin No. Assignment (TB2)
Pin No. Assignment
1,2 DC OUTPUT +V
3,4 DC OUTPUT -V
ND

Block Diagram 230 fosc : 55KHz

115

EMI RECTIFIERS POWER RECTIFIERS +V

I/P FILTER & &
SWITCHING -V
FILTER FILTER

DETECTION
FG CIRCUIT
O.L.P. PWM
CONTROL
O.T.P. O.V.P.

Derating Curve Static Characteristics (24V)

48V 32 350
100
OUTPUT RIPPLE (mVp-p)

28 300
OUTPUT VOLTAGE (V)

80
24 250

60 12V,24V 20 200
LOAD (%)

16 150
40
12 100
20
8 80

-10 0 10 20 30 45 50 60 (VERTICAL) 80 85 90 95 100 105 110 115 120 125 132

160 170 180 190 200 210 220 230 240 250 264

AMBIENT TEMPERATURE (℃) INPUT VOLTAGE (V) 60Hz

File Name:DR-120-SPEC 2018-01-12