Petrothene GA564189 Linear Low Density Polyethylene
Product Description Petrothene GA564189 exhibits good stiffness and low temperature toughness. Typical applications include trash cans, industrial containers, housewares and toys.
Regulatory Status For regulatory compliance information, see Petrothene GA564189 Product Stewardship Bulletin (PSB) and Safety Data Sheet (SDS).
Status Commercial: Active
Availability North America Application Housewares; Outdoor and Power Tools; Sports, Leisure & Toys; Trash Cans; Wire & Cable Market Compounding; Rigid Packaging; Wire & Cable Processing Method Compounding; Injection Molding; Wire & Cable
Nominal English Nominal SI
Typical Properties Value Units Value Units Test Method Physical Melt Flow Rate, (190 °C/2.16 kg) 20 g/10 min 20 g/10 min ASTM D1238 Density, (23 °C) 0.924 g/cm³ 0.924 g/cm³ ASTM D1505 Spiral Flow 12.6 in 32.1 cm LYB Method Mechanical Flexural Modulus (1% Secant) 63000 psi 440 MPa ASTM D790 (2% Secant) 55000 psi 380 MPa ASTM D790 Tensile Strength at Break, (23 °C) 1200 psi 8 MPa ASTM D638 Tensile Strength at Yield, (23 °C) 2100 psi 14 MPa ASTM D638 Tensile Elongation at Yield, (23 °C) 12 % 12 % ASTM D638 Hardness Shore Hardness, (Shore D) 57 57 ASTM D2240 Thermal Vicat Softening Temperature 196 °F 91 °C ASTM D1525 Low Temperature Brittleness, F೦ೡ <-105 °F <-76 °C ASTM D746 Deflection Temperature Under Load, (66 psi, 113 °F 45 °C ASTM D648 Unannealed)
Notes Tensile properties were run with a crosshead speed of 20 inches/min or 500 mm/min. Flexural Modulus properties were run with a crosshead speed of 0.5 inches/min or 12.5 mm/min.
LyondellBasell Petrothene GA564189
Technical Data Sheet Recipient Tracking #: Date: 9/10/2017 Page 1 of 3 Request #: 969621 Spiral Flow measures the number of inches of flow produced when molten resin is injected into a long, spiral channel (0.0625" insert), at a constant injection pressure of 1000 psi with a melt temperature of 440 °F. Deflection Temperature Under Load and Low Temperature Brittleness data are for control and development work and are not intended for use in design or predicting performance at elevated or sub-ambient temperatures. These are typical property values not to be construed as specification limits. Processing Techniques Specific recommendations for resin type and processing conditions can only be made when the end use, required properties and fabrication equipment are known. Company Information
For further information regarding the LyondellBasell company, please visit http://www.lyb.com/.
Before using a product sold by a company of the LyondellBasell family of companies, users should make their own independent determination that the product is suitable for the intended use and can be used safely and legally. SELLER MAKES NO WARRANTY; EXPRESS OR IMPLIED (INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR ANY WARRANTY) OTHER THAN AS SEPARATELY AGREED TO BY THE PARTIES IN A CONTRACT.
Users should review the applicable Safety Data Sheet before handling the product.
This product(s) may not be used in the manufacture of any of the following, without prior written approval by Seller for each specific product and application: (i) U.S. FDA Class I or II Medical Devices; Health Canada Class I, II or III Medical Devices; European Union Class I or II Medical Devices; (ii) film, overwrap and/or product packaging that is considered a part or component of one of the aforementioned medical devices; (iii) packaging in direct contact with a pharmaceutical active ingredient and/or dosage form that is intended for inhalation, injection, intravenous, nasal, ophthalmic (eye), digestive, or topical (skin) administration; (iv) tobacco related products and applications, electronic cigarettes and similar devices. (v) safety components in automotive applications, for example: air bags, air bag unit housings and covers, seat belt mechanisms, brake systems, pedals and pedal supports, steering systems.
The product(s) may not be used in:
(i) U.S. FDA Class III Medical Devices; Health Canada Class IV Medical Devices; European Class III Medical Devices; (ii) applications involving permanent implantation into the body; (iii) life-sustaining medical applications.
All references to U.S. FDA, Health Canada, and European Union regulations include another country’s equivalent regulatory classification.
In addition to the above, LyondellBasell may further prohibit or restrict the use of its products in certain applications. For further information, please contact a LyondellBasell representative.
LyondellBasell Petrothene GA564189
Technical Data Sheet Recipient Tracking #: Date: 9/10/2017 Page 2 of 3 Request #: 969621 Trademarks
Adflex, Adstif, Adsyl, Akoafloor, Akoalit, Alastian, Alathon, Alkylate, Amazing Chemistry, Aquamarine, Aquathene, Avant, Catalloy, Clyrell, CRP, Crystex, Dexflex, Duopac, Duoprime, Explore & Experiment, Filmex, Flexathene, Fueling the power to win, Glacido, Hifax, Hiflex, Histif, Hostacom, Hostalen, Hyperzone, Ideal, Indure, Integrate, Koattro, LIPP, Lucalen, Luflexen, Lupolen, Luposim, Lupostress, Lupotech, Metocene, Microthene, Moplen, MPDIOL, Nerolex, Nexprene, Petrothene, Plexar, Polymeg, Pristene, Prodflex, Pro-fax, Punctilious, Purell, Refax, SAA100, SAA101, Sequel, Softell, Spherilene, Spheripol, Spherizone, Starflex, Stretchene, Superflex, TBAc , Tebol, T-Hydro, Toppyl, Trans4m, Tufflo, Ultrathene, Vacido and Valtec are trademarks owned and/or used by the LyondellBasell family of companies.
Adsyl, Akoafloor, Akoalit, Alastian, Alathon, Aquamarine, Avant, CRP, Crystex, Dexflex, Duopac, Duoprime, Explore & Experiment, Filmex, Flexathene, Hifax, Hostacom, Hostalen, Ideal, Integrate, Koattro, Lucalen, Lupolen, Metocene, Microthene, Moplen, MPDIOL, Nexprene, Petrothene, Plexar, Polymeg, Pristene, Pro-fax, Punctilious, Purell, Sequel, Softell, Spheripol, Spherizone, Starflex, Tebol, T-Hydro, Toppyl, Tufflo and Ultrathene are registered in the U.S. Patent and Trademark Office.
LyondellBasell Petrothene GA564189
Technical Data Sheet Recipient Tracking #: Date: 9/10/2017 Page 3 of 3 Request #: 969621
