1429.1-2006 R2017 PDF

Download as pdf or txt
Download as pdf or txt
You are on page 1of 7
At a glance
Powered by AI
The key takeaways are that this standard specifies requirements for polymeric insulated electric cables for working voltages between 1.9/3.3 kV up to 19/33 kV.

The purpose of this standard is to specify requirements for polymeric insulated electric cables for working voltages between 1.9/3.3 kV up to 19/33 kV to replace the previous edition AS/NZS 1429.1:2000.

Some of the significant changes from the previous edition include expanding the range of conductor sizes, aligning the method of specifying insulation, separation sheath, metal sheath and oversheath thicknesses with IEC 60502-2, allowing MDPE as an optional oversheathing material, and making sample tests mandatory.

AS/NZS 1429.

1:2006
Reconfirmed 2017
AS/NZS 1429.1:2006

Australian/New Zealand Standard™

Electric cables—Polymeric insulated


This is a free 6 page sample. Access the full version online.

Part 1: For working voltages 1.9/3.3


(3.6) kV up to and including 19/33 (36)
kV
AS/NZS 1429.1:2006
This Joint Australian/New Zealand Standard was prepared by Joint Technical
Committee EL-003, Electric Wires and Cables. It was approved on behalf of the
Council of Standards Australia on 3 April 2006 and on behalf of the Council of
Standards New Zealand on 31 March 2006.
This Standard was published on 21 April 2006.

The following are represented on Committee EL-003:

Australasian Railway Association


Australian Electrical and Electronic Manufacturers Association
Australian Industry Group
Canterbury Manufacturers Association New Zealand
Department of Primary Industries, Mine Safety (NSW)
Electrical Contractors Association of New Zealand
Electrical Regulatory Authorities Council
This is a free 6 page sample. Access the full version online.

Energy Networks Association


Engineers Australia
Ministry of Economic Development (New Zealand)

Keeping Standards up-to-date


Standards are living documents which reflect progress in science, technology and
systems. To maintain their currency, all Standards are periodically reviewed, and
new editions are published. Between editions, amendments may be issued.
Standards may also be withdrawn. It is important that readers assure themselves
they are using a current Standard, which should include any amendments which
may have been published since the Standard was purchased.
Detailed information about joint Australian/New Zealand Standards can be found by
visiting the Standards Web Shop at www.standards.com.au or Standards New
Zealand web site at www.standards.co.nz and looking up the relevant Standard in
the on-line catalogue.
Alternatively, both organizations publish an annual printed Catalogue with full
details of all current Standards. For more frequent listings or notification of
revisions, amendments and withdrawals, Standards Australia and Standards New
Zealand offer a number of update options. For information about these services,
users should contact their respective national Standards organization.
We also welcome suggestions for improvement in our Standards, and especially
encourage readers to notify us immediately of any apparent inaccuracies or
ambiguities. Please address your comments to the Chief Executive of either
Standards Australia or Standards New Zealand at the address shown on the back
cover.

This Standard was issued in draft form for comment as DR 05363.


AS/NZS 1429.1:2006 (Reconfirmed) 2017-01-20

STANDARDS AUSTRALIA/STANDARDS NEW ZEALAND

RECONFIRMATION
OF
AS/NZS 1429.1:2006
Electric cables—Polymeric insulated
Part 1: For working voltages 1.9/3.3 (3.6) kV up to and including 19/33 (36) kV

RECONFIRMATION NOTICE

Technical Committee EL-003 has reviewed the content of this publication and in
accordance with Standards Australia procedures for reconfirmation, it has been
determined that the publication is still valid and does not require change.

Certain documents referenced in the publication may have been amended since the
This is a free 6 page sample. Access the full version online.

original date of publication. Users are advised to ensure that they are using the latest
versions of such documents as appropriate, unless advised otherwise in this
Reconfirmation Notice.

Approved for reconfirmation in accordance with Standards Australia procedures for


reconfirmation on 10 October 2016.

Approved for reconfirmation in New Zealand on behalf of the Standards Council of


New Zealand on 13 December 2016.

The following are represented on Technical Committee EL-003:


Australian Cable Makers' Association
Australian Industry Group
Electrical Compliance Testing Association
Electrical Regulatory Authorities Council
National Electrical and Communications Association
Queensland University of Technology
This is a free 6 page sample. Access the full version online.

NOTES
AS/NZS 1429.1:2006

Australian/New Zealand Standard™

Electric cables—Polymeric insulated


This is a free 6 page sample. Access the full version online.

Part 1: For working voltages 1.9/3.3


(3.6) kV up to and including 19/33 (36)
kV

Originated as AS 1429—1979.
Jointly revised and designated AS/NZS 1429.1:2000.
Third edition 2006.

COPYRIGHT
© Standards Australia/Standards New Zealand
All rights are reserved. No part of this work may be reproduced or copied in any form or by
any means, electronic or mechanical, including photocopying, without the written
permission of the publisher.
Jointly published by Standards Australia, GPO Box 476, Sydney, NSW 2001 and Standards
New Zealand, Private Bag 2439, Wellington 6020

ISBN 0 7337 7385 0


AS/NZS 1429.1:2006 2

PREFACE
This Standard was prepared by the Joint Standards Australia/Standards New Zealand
Committee EL-003, Electric Wires and Cables, to supersede AS/NZS 1429.1:2000.
This Standard differs from the previous edition in the following significant ways:
(a) The range of conductor sizes has been expanded to 1 600 mm2 .
(b) The method of specifying the thickness of insulation, separation sheath, metal sheath
and oversheath has been aligned with IEC 60502-2.
(c) MDPE has replaced PE as an optional oversheathing material.
(d) Cables with collectively screened constructions are no longer specified.
(e) The requirement for a qualification test report has been added.
(f) The range of approval has been modified.
(g) The recommended diameter of drum barrel and minimum installation bending radius
has been extended to cover triplex cables.
This is a free 6 page sample. Access the full version online.

(h) The sample test requirement has become mandatory.


In the preparation of this Standard, consideration was given to the following publications
and acknowledgment is made of the assistance received:
IEC 60502-2, Power cables with extruded insulation and their accessories for rated
voltages from 1 kV (U m = 1,2 kV) up to 30 kV (U m = 36 kV), Part 2: Cables for rated
voltages from 6 kV (U m = 7,2 kV) up to 30 kV (U m = 36 kV)
IEC 60811, Common test methods for insulating and sheathing materials of electric cables
and optical cables (all Parts)
The nominal cross-sectional areas of the conductors specified herein are identical with the
values specified in AS/NZS 1125, Conductors in insulated electric cables and flexible
cords.
The dimensions for insulation and oversheath thicknesses are identical with the values
recommended in IEC 60502. Certain tests and criteria in this Standard are more stringent
than those in IEC 60502.
Two types of insulation compounds are specified in this Standard, namely insulation
comprising cross-linked polyethylene (XLPE) and insulation comprising ethylene propylene
rubber (EPR).
Although the Standard provides tables of insulation thicknesses and the necessary
information to establish precisely the dimensions of the cable protective coverings, no cable
dimension tables are provided owing to the variety of cable constructions that could
possibly affect such dimensions.
The terms ‘normative’ and ‘informative’ have been used in this Standard to define the
application of the appendix to which they apply. A ‘normative’ appendix is an integral part
of a Standard, whereas an ‘informative’ appendix is only for information and guidance.
Statements expressed in mandatory terms in notes to tables and figures are deemed to be
requirements of this Standard.
This is a free preview. Purchase the entire publication at the link below:

AS/NZS 1429.1:2006 (R2017) Electric cables -


Polymeric insulated - For working voltages 1.9/3.3
(3.6) kV up to and including 19/33 (36) kV
This is a free 6 page sample. Access the full version online.

Looking for additional Standards? Visit SAI Global Infostore


Subscribe to our Free Newsletters
Do you need to Manage Standards Collections Online?
Learn about LexConnect, All Jurisdictions, Standards referenced in Australian legislation
Do you want to know when a Standard has changed?
Create safe work processes for the workplace with our Safe Work Method Statements

Learn about other SAI Global Services:

LOGICOM Military Parts and Supplier Database


Metals Infobase Database of Metal Grades, Standards and Manufacturers
Materials Infobase Database of Materials, Standards and Suppliers
Database of European Law, CELEX and Court Decisions

Need to speak with a Customer Service Representative - Contact Us

You might also like