Scribd
Upload
1K views

Cobas c311

1. The document discusses the procedures for using a Cobas c 311 analyzer to perform clinical chemistry measurements. 2. Key steps include preparing the analyzer, loading samples, reagents and controls, performing calibrations and quality control checks, and running patient samples to measure analyte levels in an automated fashion. 3. The analyzer uses spectrophotometric techniques to rapidly and simultaneously process multiple samples, improving efficiency in clinical chemistry testing.

Uploaded by

riri
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
1K views

Cobas c311

1. The document discusses the procedures for using a Cobas c 311 analyzer to perform clinical chemistry measurements. 2. Key steps include preparing the analyzer, loading samples, reagents and controls, performing calibrations and quality control checks, and running patient samples to measure analyte levels in an automated fashion. 3. The analyzer uses spectrophotometric techniques to rapidly and simultaneously process multiple samples, improving efficiency in clinical chemistry testing.

Uploaded by

riri
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 5

Topik: Pemeriksaan Kimia Klinik menggunakan alat Cobas c 311 analyzer Tujuan: untuk mengukur

kadar zat-zat yang terkandung dalam darah Metode: Spektrofotometer Prinsip: melakukan prosedur
pemeriksaan kimia klinik secara otomatis mulai dari pemipetan sampel, penambahan reagen,
inkubasi serta pembacaan serapan cahayanya, yang dapat dilakukan dengan cepat dan bisa
digunakan untuk memeriksa sampel dengan jumlah yang banyak secara bersamaan.
1.Perpraring the analyzer
Always take suitable safety measures as d
escribed in the Operator’s manual
a.

Check that the container for highly concentrated waste is clean and empty. b.

Check for any leaks inside or around the instrument. c.

Check that the cell covers, pipetter probes, ISE sipper nozzle, and the rinse nozzles are clean. If
trouble occurs, take the necessary remedial action.
2.

Starting the analyzer


a.

Switch on instrument. When the automatic power up is specified in the analyzer software, the pipe
function will be executed automatically. b.

Switch on control unit computer. c.

Switch on water supply. d.

Logon to the analyzer software using your operator ID and password. e.

When the analyzer is in sleep mode, it starts up automatically by using the sleep pipe function
(Power Up Pipe with starting time)
3.

System Overview
–
Workflow Guide
Daily Maintenance a.

Check for alarms b.

Perform required maintenance action or maintenance pipe function:

Daily maintenance

Select
Execute
4.

Sample Data Clear


All measurement result of routine and STAT samples will be deleted. The measurement results of
quality control samples will be moved to the QC view area of data storage control section.

Sample data clear

Clear or backup and clear

OK
5.

Reagen preparing
a.

Select the preventive action check box on the system overview screen.

Reagent preparing

Reagent load/unload list

Yes The reagent load list will be printed for reagents with yellow, purple, or red alarm. b.

Load reagent onto the instrument according to the reagent load list. c.

Remove all empty cobas c packs from the analyzer.


6.

Replacing ISE Reagents


a.

Before replacing a reagent bottle, put the analyzer in Maintenance mode or Shutdown status. b.

After replacement turn the maintenance switch back to Operation mode (or power up the analyzer if
it was in Shutdown status). c.

Perform a Reagent Prime if an ISE Ref. Or ISE IS bottle has been replaced:

Reagent preparing
Reagent prime d.

Sellect all e.

Execute f.

Recalibrate the ISE unit before you resume routine operation.

7.

Calibration and QC Select


The analyzer automatically recommends calibrations and controls to be perfomed. But the
recommended calibrations and QCs must be confirmed by the operator before they can be
measured a.

Calibration and QC select: Recommended b.

Print the Calibrator and QC load list: Print c.

Load calibrator and QC samples onto the analyzer according to the calibrator and QC load list. d.

Start
8.

End of routine
a.

Load wash solutions for ISE wash: Pos. W1: ISE cleaning solution SysClean Pos. W2: ISE activator
SmpCln Position 1: Multiclean b.

Utility: Maintenance c.

Select maintenance item (10) ISE wash d.

Select: Execute
9.

Application, Calibration and QC set up Loading application parameters from cobas link
a.

Utility

Application
Download b.

Select one of the avaible search conditions c.

Search d.

Select the check box of the parameters to be downloaded. e.

Download

OK f.

Check that the parameters have been downloaded

10.

Loading calibrator data from cobas link


a.

Calibration

Install b.

Select a blank line

Add c.

Type all necessary data in the add calibrator window

OK d.

The new calibrator appears on the calibrator list e.

Edit f.

Type in the concentration values for each test. g.

Update
OK
11.

Loading control data from cobas link


a.

QC

Install

Download b.

Select one of the available search conditions c.

Search d.

Select the check box of the control to be download e.

Download

OK f.

Check that the control data has been downloaded.

You might also like