Mack Section 3 New

BODY BUILDER INSTRUCTIONS
Mack Trucks
Electrical Wiring and Connections

PI / CHU, AN / CXU, GR / GU, TD
LR, TE / MRU
Section 3
Introduction
This information provides design and function, specification and procedure details for
Electrical Wiring and Connections for MACK vehicles.
Note: For information on mDrive PTO installation and wiring see Section 9 PTO
Installation, mDrive.
Note: For information on PTO parameter programming see Section 9 PTO Parameter
Programming.
Unless stated otherwise, following a recommendation listed in this manual does not
automatically guarantee compliance with applicable government regulations. Compliance
with applicable government regulations is your responsibility as the party making the
additions/modifications.
Please be advised that the MACK Trucks, Inc. vehicle warranty does not apply to any
MACK vehicle that has been modified in any way, which in MACK's judgment might affect
the vehicles stability or reliability.
Contents
• “ISO 26262 Functional Safety Manual”, page 3
• “Abbreviations”, page 4
• “General Wiring Definitions”, page 5
• “Routing and Clipping Guidelines”, page 6
• “Body Builder Connectors, Schematic Examples”, page 18
• “Remote Start n Stop”, page 24
• “Remote Engine Stop”, page 25
• “Adding Auxiliary Accelerator Pedal”, page 26
• “BodyLink III”, page 27
• “Auxiliary Switch Locations (Cab)”, page 31
• “Power Connections”, page 32
• “Control Link II”, page 38
• “RP170A Refuse Related Chassis to Body Interface Connectors”, page 51

Mack Body Builder Instructions PI / CHU, AN / CXU, GR / GU, TD, LR, TE / MRU
USA143320766 Date 11.2018 Page 1 (103)
All Rights Reserved
• “LR Workbrake”, page 55
• “Wiring J1939”, page 57
• “9-pin Diagnostic Connector”, page 59
• “16-pin Diagnostic Connector”, page 60
• “Termination Resistor”, page 65
• “Parameter List”, page 66
• “Multiplexing Body Builder J1939 CAN ”, page 82
• “Support Inbound and Outbound J-1939 Message Information ”, page 90
• “CAN Bus Road Speed Signal Kit”, page 100
PI / CHU, AN / CXU, GR / GU, TD, LR, TE / MRU

USA143320766 Date 11.2018 Release 01 Page 2 (103)
ISO 26262 Functional Safety Manual
Scope
This section describes the functional safety aspects related to the interface between the vehicle and the body builder
equipment.
Introduction
ISO 26262 is the functional safety standard for road vehicles. Functional safety addresses safety related functionality imple-
mented in electronics and software. Mack has during 2018 initiated development of new vehicle functions and systems ac-
cording to ISO 26262 after the standard became applicable to trucks, buses and trailers. Before ISO 26262, Mack followed
other internal processes addressing functional safety.
The truck will gradually be made compliant to ISO 26262. However, it will take several years until the complete truck is com-
pliant to the standard.
The status of the truck related to functional safety with regards to ISO 26262 will be described in this status. Continuous up-
dates will be made to reflect the current status of the truck.
The ASILs of the body builder interface characteristics will be documented and it will be described in which sense the interfa-
ces meet the different ASILs. This section will also contain information on requirements and constraints for the usage of the
body builder interface. In case specific safety measures have to be applied by the body builder, this shall be stated in this
section.
When a body builder needs anything that is not described or when the ASIL of the characteristic is not according to the body
builders expectations, the body builder shall contact Mack for guidance. This section will be referenced from other body
builder sections when applicable.
Current status of the truck in relation to ISO 26262

The existing trucks are developed according to Mack internal processes addressing functional safety, applicable before ISO
26262.
Presently no functions or systems in the trucks have been developed according to ISO 26262.
USA143320766 Date 11.2018 Electrical Wiring and Connections Page 3 (103)
All Rights Reserved
Abbreviations
• ACC Adaptive Cruise Control
• BOC Back of Cab
• CAN Controller Area Network
• CDS Custom Defined Statement (replaced by DCL)
• DCL DataMax Control Language
• ECM Engine Control Module
• EHT Electronic Hand Throttle
• EMS Engine Management System
• ESC Engine Speed Control
• FMI Failure Mode Identification
• GMT Greenwich Mean Time
• MID Message Identifier (J1587 source)
• PGN Parameter Group Number (J1939 message ID)
• PID Parameter Identification (J1587)
• PID Product Identification (order code)
• PTO Power Take Off
• PTT2 Premium Tech Tool 2
• SA Source Address (J1939 unit identifier)
• SID Subsystem Identification (J1587)
• SPN Suspect Parameter Number (J1939 parameter)
• SSC Single Speed Control
• TCM Transmission Control Module
• VDA Vehicle Data Administration (OEM database)
• VECU Vehicle Electronic Control Unit
• V-MAC Vehicle Management And Control (Mack brand electronics name)
All Rights Reserved
General Wiring Definitions
The general wiring definitions provides a standardized list of terminology used in running wires, hoses, and cables through-
out the vehicle.
Items capable of causing damage to the routed commodity in a rubbing condition during vehicle
Abrasive Surface
operation
AWG American Wire Gauge
Bundled With A number of items tied, wrapped, or otherwise held together

A nylon plastic self-sizing strap, UV resistant, capable of bundling specified load(s) during vehicle
Cable Tie
operation
Chafing To wear away by rubbing
Contacts Items touching each other.

Crimped A routed commodity that is bent or pressed into ridges
Damaged An item that differs from its original condition
Drooping Routed items hanging downward which are detrimental to safe vehicle operation
(Pertaining to the Compressor Discharge Line) A high point in the routing of the Compressor Dis-
Dual Fall charge Line (located on the engine) whereby any collected moisture is allowed to fall in two different di-
rections where it is either dissipated by heat or is purged
High Current
Wire sizes 13 mm sq. (0.5 inches sq.) (6 AWG) and larger
Electrical Cables
High Nut Extended clamp length
Kinked A tight bend, curl, or twist in the routed commodity causing flow to be restricted
Low Current Elec-
Wire sizes 8 mm sq. (0.3 inches sq) (8 AWG) and smaller
trical Cables
Low Nut Standard clamp length
Material Grade 30 Minimum yield strength of 30,000 psi
Material Grade 50 Minimum yield strength of 50,000 psi

Verb typically used in a statement of practice that is a permissive condition and carries no requirement
May
or recommendation. It can be included to alter statements of mandate or recommendation
Not Secured Items not fastened, bundled or tied
Plastic Conduit Corrugated or smooth wall tubing used to protect hoses, harnesses, cables, tubing, pipes, etc.
Puncture Small hole or wound
Routed With Items taking the same path but not attached to each other (i.e., parallel but separate)
Rubbing Items that contact each other and have independent movement
Verb typically used in a statement of required, mandatory or specifically prohibitive practice regarding
Shall
routing and clipping
Sharp Edge A surface capable of cutting or piercing the routed commodity during vehicle operation
Verb typically used in a statement of recommended, but not mandatory, practice in typical situations
Should with deviations allowed if Engineering judgement or Engineering study indicates the deviation is
appropriate
All Rights Reserved
Twisted Distorted from the routed commodities’ original shape about it’s cross-sectional center line
Touch Items that contact each other but do not have relative movement
Routing and Clipping Guidelines

1 Brackets used in routing and clipping should be Material Grade 50 or better to ensure sufficient clamp load when sharing
joint connections with cross members or other structural members. This applies only to joint connections using a low nut.
Brackets of Material Grade 30 are acceptable provided the shared joint is using a high nut. The area of the clip bracket
under the bolt head must be a least as large as the bolt head itself.
2 Clips that scratch exterior mounting surfaces shall not be used (i.e., barbed/spring type) unless the material is non-corrod-
ing (i.e., plastic). Clips must have rust protection.
3 Clip sizes should adequately secure the bundle without restricting flow, causing collapse, or preventing relative
movement.
4 Bundles shall be supported at 24 inches (600 mm) maximum intervals, a cable tie should be used between clip points on
bundles with the exception of electrical wiring harness which shall have a maximum support distance of 18 inches (450
mm) and a cable tie on bundles between clip points. When air and electrical lines are bundled together, the commodity
with the greater cross sectional area may determine the support spacing. A minimum of two cable ties shall be used be-
tween clip points to bundle electrical lines when the larger interval is used.
W3104131
1 Support electrical cables every 18 inches (450 mm)
All Rights Reserved
Support Distances, Continued
W3104144
1 Support cables near connectors every 4 inches (100 mm)
1 Electrical cables and wiring harnesses are to be secured 4 inches (100 mm) from the wire insertion end of the connector
or clipped to the body.
2 Routing and clipping on purchased components (i.e., engine/transmission) should not include removing or replacing a
bolt(s), nut(s) or screw(s) installed by the manufacturer. In such cases where this is unavoidable, the bolt(s), nut(s) or
screw(s) shall be re-installed to the manufacturer’s specifications.
3 Bundles should not contact sharp edges of cross members. Contact may occur if it is against a smooth surface, a smooth
radiused edge or a coined edge and the bundle is secured to prevent independent movement.
4 Hoses, tubing, pipes and electrical conduits shall not rub each other but may touch.
5 The fabric braided portion of the compressor discharge hose is compatible to be bundled with all routed air lines.
6 The compressor discharge pipe shall be routed independent of all other routing.
7 Electric cables/harnesses must not be bundled with fuel or hydraulic lines. The electrical cables/harnesses may be routed
parallel with fuel or hydraulic lines, however must remain separated by approved clipping materials. When design control
is possible, electrical cables/harnesses will be routed above fuel or hydraulic lines. If fuel or hydraulic lines must route
above circuit protected electrical cables /harnesses, the fuel or hydraulic lines will have no fittings or potential leak points
above electrical cables/harnesses and shall be minimized to the shortest distance possible over low current electrical ca-
bles/harnesses.
8 All associated markings on air and electrical harnesses should have a corresponding clipping apparatus.
9 Critical clipping locations shall be designated on the component to insure proper placement in the vehicle (i.e., tape).
10 Maximum support distance for compressor discharge rigid pipe, 30 inches (762 mm). Pipe to be isolated from support
brackets (i.e. rubber isolator).
11 Maximum support distance for compressor discharge flex hose, 24 inches (600 mm).
12 Compressor discharge line should have a constant fall from compressor to air dryer. A dual fall is allowable provided it oc-
curs on the engine and within 24 inches (600 mm) of the compressor.
13 Maximum allowable dip in compressor discharge pipe/hose is one half the outer diameter of the pipe/hose. Preferred rout-
ing should have no dips in any of the routing. This is to avoid line blockage due to water collecting and freezing in the line.
All Rights Reserved
Heating Specifications
In order to maintain the integrity of the cables and hoses, observe the following specifications for routing near a heat source.
Cable, hose, or harness

Specification
type
Electrical cables and wiring 5 inches (130 mm) in all directions from turbocharger, exhaust components, and other high
harnesses heat components
Unprotected hoses, tubing,
6 inches (150 mm) above, 5 inches (130 mm) beside and 4 inches (100 mm) below
harnesses, and cables
Hoses, tubing, harnesses,
and cables protected by re- 3 inches (76 mm) above, 2 ½ inches (63,5 mm) beside and 2 inches (51 mm) below
flective heat sheathing
Silicone transmission coolant 2 inches (51 mm) from exhaust manifold and turbo (with reflective heat sleeving), 1 inch (25
hoses mm) from exhaust pipe
Hoses, tubing, harnesses,
and cables protected by a
3/8 inch (10 mm) between the component and the heat shield. (Not valid for fuel lines)
heat shield (no reflective
sheathing)
Refrigerant suction hoses 8 inches (200 mm)
W3109897
1 Heat Radius from the Turbocharger, Front: 5 inches (130 mm)
All Rights Reserved
W2106268
The SCR, DPF, and exhaust piping generate substantial heat. Keep electrical cables away from these components.
All Rights Reserved
Clipping Guidelines
Clipping brackets should be designed and mounted to adequately support the bundle. Clips should be mounted in a hanging
position or supported along three-quarters of the horizontal mounting surface. Orientations that do not conform to the illustra-
tions shall be tested.
1 When hoses, wires, and cables cross one another, secure them with a clamp. This prevents the sawing motion that could
abrade them.
2 When routing flex hoses that are bent in two planes, clip them to prevent twisting. Clamp the hose at the point where the
hose changes planes. The clamp has the effect of dividing the hose into two assemblies. If the section of the hose is bent
in the same plane as the movement, the bend will absorb the movement and the hose will not twist.
W3103550
W3103553
All Rights Reserved
When routing connectors with cable ties, ensure the cable ties do not contact the connector locking tab. Cable ties should al-
so not contact the bare wire.
W3104148
W3104149
All Rights Reserved
Battery Cable Guidelines
The battery cable guidelines prevent electrical interference that can occur from improperly routed cables. In addition, the
guidelines prevent cable damage through abrasion.
1 Battery cables with standard SAE stranding shall be supported at 16 inches (400 mm) maximum intervals. A separator
type cable tie or an independent separator with cable tie may be used between clip points. No relative movement may oc-
cur between cables. If two (2) cable separators are used, they are to be installed equidistant from each other and ar-
ranged on a straight line, a maximum span between clip points of 24 inches (600 mm) may be used.
2 Strain relief clipping shall be provided for the battery and starter motor terminals. The strain relief clip shall be located with
no relative motion to the terminals. The strain relief clip should be located close to these terminals and shall be within 20
inch (500 mm) cable length to the starter terminals.
3 Grommets shall be installed at points where cables pass through sheet metal or frames.
4 Routing shall avoid exposed edges of frame members, abrasive surfaces, and all sharp edges. When routing inside the
frame, ensure that no contact with the frame is made with uncovered cables. Uncovered battery cables, external of the
battery box, shall be routed independent of all other conduits. Covered cables may be bundled with other similarly covered
conduits and air piping with a secured separator. Do not route with/under fuel lines.
5 Cables should be clipped as close as possible to all cable bends.
6 Battery cables shall not be located within 5 inches (130 mm) of engine exhaust related components or other heat sources
without heat coverings or heat shielding. Testing shall be performed to determine effects of closer allowances and the use
of heat shields. Battery cables should not be installed in any area directly above engine exhaust related components.
7 Where cables flex between moving parts, the last supporting clip shall be securely mounted such that relative movement
does not promote chaffing.
8 Battery cables shall not support any mechanical loads other than their own mass.
9 Minimum bend radii of battery cables should be 3 times the cable diameter for standard SAE strand cable.
W3104133
1 Tube Diameter
2 Circle Diameter ( 3 x Tube Diameter)
All Rights Reserved
Battery Guidelines, Continued
1 Star washers shall not be used on current path connections including grounds.
2 Asphalt type loom shall not be used for battery cable protection applications.
3 Battery cables shall not rub each other or surrounding items, but may touch when all items have no independent move-
ment. Uncovered battery cables may not touch each other outside the battery box.
4 All exposed exterior to cab circuit ends shall be coated with a dielectric protective coating. Thickness to be 0.13 – 0.3 in-
ches (3.5 – 7 mm) wet, full coverage, 3 inches (76.2 mm) diameter, or shall be completely covered with required inhibitor.
5 Clip orientations should be per illustration or installation drawings utilizing compression or heavy duty clip.
6 Plastic conduit may be bundled and cable tied with covered battery cables when all items have no independent movement
with each other. Battery cables may touch each other, plastic conduit or the battery, inside the battery box.
7 Covered battery cables may be securely tied or clamped to each other if no independent movement exists. Cables at-
tached to the same terminal stud may be tied or clamped to each other.
8 Battery cable ends at the starter motor posts should be installed and positioned first with the engine harness terminals as-
sembled after. Starter terminals that come with the starter may be first on the starter studs. Terminals shall not be re-con-
figured or bent.
9 Frame bolt placement, adjacent to the battery box, should have the bolt or screw threaded end facing away from the bat-
tery box and any related cables. Wrench grip type bolts should not be used in the frame at the battery box area. Non-
wrench grip type bolt or screw threaded ends may face toward the battery box only if clip bracketing or shielding shall be
provided to prevent any possible cable contact with frame mounted hardware. Bolts that mount the battery box to the
frame may be oriented toward the battery box.
10 Added abrasion protection should be used where the cable contacts other routed commodities or surfaces with no inde-
pendent movement such as frame rail surfaces or transmission and engine castings. Polyethylene, polypropylene, nylon
conduit and thick wall heat shrink tubing may be used for added abrasion protection.
11 Cables should be located to afford protection from road splash, stones, abrasion, grease, oil and fuel. Cables exposed to
such conditions should be further protected by either, or a combination of, the use of heavy wall thermoplastic insulated
cable, additional tape application, plastic sleeve or conduit.
12 Anytime an existing fastener is used to secure a clipping bracket (or any similar device), the fastener shall be re-torqued
to the value specified in the original documentation given for the fastener.
13 Each exposed exterior circuit end must be coated with a dielectric protective coating. Thickness to be 0.13 – 0.3 inches
(3.5 – 7 mm) wet, full coverage, 3 inches (76.2 mm) diameter.
14 Do not use box clamps to secure battery cables.
15 In addition to berringer clamps, use double-head tie clamps.
W3077595
Berringer clamps are recommended for securing battery cables to each other.
All Rights Reserved
W3105372
Box Clamps (shown above) are NOT to be used for securing battery cables to each other.
W3105374
Double-head tie clamps may be used to route battery cables.
All Rights Reserved
Ring Terminal Assembly
Assemble terminal carrying the highest current (largest gauge wire) first, then graduate to the smallest gauge up to the fas-
tener. Use a maximum of three (3) terminals per stud (unless otherwise specified on an illustration drawing).
W3104152
When attaching ring terminals with a fastener, tighten the fastener to appropriate torque so that the contact area will touch
the terminal at any point, in a full circle that is part of the terminal.
W3104153
1 Contact Area
2 Fastener
3 Stud
4 Terminals
All Rights Reserved
When attaching multiple terminals, position the terminals at an angle to allow maximum contact of the terminal surface. Ter-
minals are not allowed to bend other than their natural form. Terminals may be stacked back to back.
W3104154
Improperly fanned terminals result in unacceptable bends.
W3104155
All Rights Reserved
NOx Sensor Routing
The NOx sensor requires unique routing considerations. The NOx sensor harness must not be bundled with other wiring har-
nesses. However, it may be routed with other harnesses as long as they are not high voltage cables. The sensor harness is
a set length and no altering or modifying of the NOx sensor harness is allowed.
W3104156
Conventional
W3109892
Cabover
Note: DO NOT splice into a V-MAC, ABS/ATC or any other electronic control unit harness.
Do not cut or tap into the J1939 green/yellow twisted wires or any other wire or harness used on this vehicle. Use the pro-
vided connectors, and only add approved J1939 components with validated software. Failure to comply may result in person-
al injury or equipment damage. Any cutting, splicing, alteration or modification to the wiring will Void the Mack Trucks
Warranty on the Electrical System.
All Rights Reserved
Body Builder Connectors, Schematic Examples
Third party devices are often installed on MACK trucks. These devices need information (vehicle speed, gear, etc.) to oper-
ate safely and efficiently. However these devices are not quality controlled as far as MACK is concerned, and are not part of
the main control databus. Therefore, MACK provides an external connector to supply a body device with the necessary infor-
mation it needs to function properly.
MACK trucks do not use an external body builder module (BBM). In MACK trucks, the functions of the BBM are managed by
the Vehicle Electrical Control Unit (VECU) and are transmitted to the body device via an SAE J1939 connector. SAE J1939
is a communications link between standalone vehicle modules. This data link is commonly referred to as the “Control Data
link”. It is used primarily to transmit control signals that are shared between other standalone modules. The information on
the SAE J1939 control link is used for control functions. Fault messages or diagnostic information also transmits across this
link. These control signals may be for engine, transmission, brakes or a number of other vehicle control needs. The J1939
operates at 250,000 bits per second, which is approximately 26 times faster than the J1708/1587 data link. This higher speed
allows the system to operate at a faster sampling rate and higher resolution, thus enabling better control of vehicle functions.
Terminating Resistors
Terminating resistors are wired to each end of the SAE J1939 data link to prevent signal reflections. They must remain con-
nected for the data link to function properly. The resistance value of each termination resistor is 110–130 Ω. When properly
installed in the data link, their combined resistance is 50–70 Ω since they are connected in parallel.
The termination resistor at one end of the SAE J1939 data link is located in the fuse/relay center (FRC) near the vehicle elec-
tronic control unit (VECU) and the other near the engine control module (ECM). On vehicles equipped with MACK engines,
the termination resistor at the engine end is located inside the ECM. On vehicles equipped with Cummins engine, the termi-
nation resistor is located in the harness area just outside of the ECM.
A SAE J1939 data link connection is located at the transmission area in the chassis harness. On vehicles equipped with an
electronically controlled transmission (Allison/Autoshift II/Meritor Freedom Line), the connection to the transmission is lo-
cated at the chassis harness. On vehicles equipped with a manual non-electronically controlled transmission - the connector
stub will have an un-terminated blanking plug installed.
Only two termination resistors are used in each data link. Never install more than two terminator resistors in one data link. If
more than two resistors exist in the SAE J1939 data link circuit, incorrect or absent signals may occur. You can easily check
to see if you have two resistors by measuring the resistance between pin C and D for the 9-pin diagnostic connector, or pin 3
and 11 for the 16-pin diagnostic connector, with the ignition key in OFF position. The correct resistance is 50 – 70 Ω. The ter-
mination resistors should each have a resistance of 110 – 130 Ω when tested individually.
Notes
All Rights Reserved
Electrical Wiring and Connections
Main Power and Starting Circuits
Figure 1 shows the starter circuits. Note that the EMS and VECU directly control the starter relay. The EMS inhibits starter
for engine running, starter overheat and PTO. The VECU inhibits the starter mainly for transmission in gear.
Figure 2 shows the main power circuits. Ignition and “EMS” power are controlled by the VECU through relays. “EMS” power
is connected after the key is turned on and remains on during crank and for some seconds after key off, mainly to service the
Engine Management System. Ignition power is similar, but is disconnected during crank and supplies items not necessary
for engine start. MACK conventional trucks actually have a second set of ignition circuits for items not normally needed for
driving (e.g. Sleeper) which also supplies one of the Granite BodyLink III power pins indicated in Figure 7. The first and sec-
ond power relays are also shut off at low voltage. The first relay powers off at a lower threshold than the second.
W3113939
Fig. 1 Main Power and Starting Circuit
All Rights Reserved
W0113940
Fig. 2 Battery & Ignition - Switched Supplies - Conventional Trucks
“IGN” circuits will be disconnected at LOW VOLTAGE and during STARTING.
“EMS” circuits remain powered while at key ON or CRANK and may remain powered at key OFF.
All Rights Reserved
Vehicle Control Unit (VECU) Connections
W3088359
Fig. 3 Vehicle Control Unit (VECU) Connectors
Notes
All Rights Reserved
Description of VECU Pin Layout
VECU Connector A (Green)
Pin Number Type Mack Name
PA-1 DI-H Cruise Control: Set/Decel

PA-2 DI-H Cruise Control: Resume/Accel
PA-3 DI-H Cruise Control: On/Off
PA-4 DI-H A/C On
PA-5 DI-H Service Brake
PA-6 DI-H Key Switch Crank
PA-7 DI-H —
PA-8 DI-H Clutch
PA-9 DI-H Neutral
PA-10 DI-H Air Suspension Interlock
PA-11 DO-L (1A) DRL Control
PA-12 – Ground
PA-13 – Battery ( + after PWR )
PA-14 DI-H Key Switch Ignition
PA-15 – J1939 + BBM

PA-16 – J1939 – BBM
PA-17 DI-H CDS 2 switch / PTO 4
PA-18 DI-H IVS2 used for Volvo Automatic gearbox
PA-19 DI-H Fan Override

PA-20 DI-H Engine brake 2
PA-21 DI-H Engine brake 1
PA-22 DI-H EOL

PA-23 DI-H IVS 1
PA-24 DI-L —
PA-25 DI-L Interwheel Lock
PA-26 DI-L 5th Wheel Slide Switch
PA-27 DI-L Remote Engine Shutdown
PA-28 DI-L Hood Tilt Switch

PA-29 DI-H PTO1
PA-30 DI-H DRL Override
All Rights Reserved
VECU Connector B (Blue)
Pin Number Type Mack Name
PB-1 DO-L (1A) Power Relay #1 (load shedding)
PB-2 DO-L (1A) Power Relay #2 (load shedding)
PB-3 DO-L (1A) Interwheel Diff Lock
PB-4 DO-L (1A) 5th Wheel Slide Interlock /Regen Inhibited
PB-5 (12 v, 50 mA) Output Supply 4
PB-6 Frequency Input Vehicle Speed Sensor +
PB-7 DI-H PTO 2

PB-8 AI (4K) Throttle Pedal Signal
PB-9 AI (2 - 10K) Spare
PB-10 (5V, 10 mA) Output Supply 1, (T.P.)
PB-11 DI-L Parking Brake
PB-12 DI-L EB Steering wheel 1
PB-13 DI-L RH Operation
PB-14 AI (1.5-4K) Spare
PB-15 DO – L (0.2A) EMS Relay
PB-16 DO-L (1A) Aux Fan
PB-17 DO – H (10 mA) Buffered IVS 1 (Only EMS)
PB-18 DO-L (1A) PTO output
PB-19 (12V, 70mA) Output Supply 3
PB-20 Frequency Input Vehicle Speed Sensor -
PB-21 DI-H CDS 1 / PTO 3

PB-22 — Analog Ground
PB-23 — Analog Ground
PB-24 AI (2 - 10K) —
PB-25 (6.5-9V, 15mA) Output Supply 5
PB-26 (5V, 10 mA) Output Supply 2
PB-27 AI Spare
PB-28 DO – H ( 2A) Starter Control (ASSIST or starter protection)
PB-29 DI-L Door Switch

PB-30 DI-H Shut Down Override
VECU Connector C (Green)

Pin Number Mack Name
PC-1 J1587 B
PC-2 J1587 A
PC-3 —
All Rights Reserved
Pin Number Mack Name
PC-4 J1939 H
PC-5 J1939 L
Remote Start n Stop

Note: This is only a suggestion for a body builder installed system.
W3121912
Fig. 4 Remote Start N Stop V-MAC IV

Note: Refer to “Remote Start N Stop V-MAC IV, Schematic Components” table for descriptions and part
numbers.
Remote Start N Stop V-MAC IV, Schematic Components

Description Part Number
Relay 25171095
Relay Connector 20865681
Terminal Female 925AM22
Terminal Male 20865699
Secondary Lock 25154889
Switch Drive Position 25153559
Switch Drive Position Connector 21402299
Terminal Drive Position Switch 25091569
Park Brake Switch 25171211
All Rights Reserved
Remote Engine Stop
If a chassis was ordered with “Remote Engine Stop”, a relay is pre-installed in the harness. Installation of the push button
switch is all that is required.
If installing “Remote Engine Stop” to a chassis (TE / MRU, LR and Conventional Chassis’), relay P/N 25082390 must be in-
stalled in addition to installing the push button switch. Only TE / MRU and LR models are pre-wired for the Remote Engine
Stop.
Note: For Remote Engine Stop to work you must run an accessory kit and P/N 85137397 reprogram the VECU (Can only be
done by a Dealer) and parameters need to be programmed. See “Remote Engine Stop” in the Body Builder, Parameter Pro-
gramming service bulletin.
Note: The input to the VECU pin A27 (Green 30-way connector on VECU) is an active low digital input that must be attached
to an isolated signal ground.
DO NOT switch chassis/cab ground to pin A27 of the VECU. Interference from other components on the chassis/cab
ground could cause an engine shutdown when not requested by the body builder.
Note: The switching of ground to an input that carries a very low current requires special switching equipment. It is recom-
mended using a switch with gold contacts, or a relay to switch the signal ground to Pin A27 of the VECU.
Gold resists corrosion on the contacts and relays have enough ‘swiping’ motion on the contacts to help keep them clean.
W3113955
Fig. 5 Remote Engine Stop
All Rights Reserved
Adding Auxiliary Accelerator Pedal
Below is a suggestion for adding an auxiliary accelerator pedal, based on the Mack LR dual steering solution.
The pedal is wired in parallel using a multi-pin selector switch. If the signal is not switched between the two accelerator ped-
als, a fault code may be generated due to high current at the throttle pedal signal input line (VECU B-8).
Note: See data link system before using such a device.
Note: An identical pedal is needed for the auxiliary sensor accelerator pedal because it requires an IVS signal. A substitute
type pedal may cause a fault code and is not recommended.
W3113956
Fig. 6 Auxiliary Acceleration Pedal Signal

Note: Refer to “Auxiliary Acceleration Pedal Signal, Schematic Components” table for component ID(s) and
descriptions.
Notes
All Rights Reserved
BodyLink III
BodyLink III is the standard Mack Granite straight truck body builder electrical interface. It consists of a 29-pin electrical
quick-connector and grounding stud mounted just under the rear of the cab (near BOC). BodyLink III includes an electrical
pin-out label. Also available with BodyLink III is a cab pass-thru between the seats. Note that the carpeting or floor mate is
not cut at the factory to avoid unnecessary noise if not used. Also available is a ‘BodyLamp’ dash light to indicate typically
when the dump body is elevated. This lamp is activated via pin #17 when grounded. Also available with BodyLink III are as-
signable (can be labeled) dash switches. These switches output via pins 8 to 14 on the BodyLink III connector. A female con-
nector and pins are included with BodyLink III, typically supplied in the cab with the sales and service literature packets.
Note: The BodyLink III BOC connector is supplied with the mating connector housing and terminal pins from the factory. If
additional pins or connectors are required they can be purchased from your local Mack Dealer. The connector housing is
25177195 and the terminal kit is 21750652.
W3084959
Fig. 7 Granite BodyLink III Components

1 BodyLink III Connector
2 Pass-Thru
3 Switch
All Rights Reserved
There is a new display in Co-Pilot to alert the driver that the body is up or out of position.
W8136998
Fig. 8 Body Raised Out of Position
Order Codes for Body Connections (Granite BodyLink III)
Item Order Code Model Status Description

29-pin under-cab connector,
BodyLink III w/Cab Granite and MHD
B83–0025 Standard BOC label, female connector,
Pass-Thru Trucks
cab pass-thru.
BodyLink III w/o Cab Granite and MHD Same as above without cab
B83–0026 Optional
Pass-Thru Trucks pass-thru.
Body Position Indica- Granite and MHD Standard w/B83–
DIL-BOOP Co-Pilot Warning Screen
tor Screen (Co-Pilot) Trucks 0025B83–0026
Six (6) assignable dash rocker
Six (6) Assignable Granite and MHD
AUXSW-6B Optional switches w/ lenses (5 on-off, 1
Body Builder Switches Trucks
momentary)
Notes
All Rights Reserved
W3092527
Fig. 9 Granite BodyLink III Routing Beneath Driver Seat

1 Rubber Adhesive Tape
W3092528
Fig. 10 Granite BodyLink III Cab Pass Through and Connector

1 Body Builder Harness
2 Gasket
3 Spacer
4 Nut, Panel
All Rights Reserved
W3064928
Fig. 11 Granite BodyLink III 29-pin Connector, Wire Insertion Side of Connector.
Pin Chart for Granite BodyLink III 29-pin Connector
Pole Description
1 BATTERY POWER (30A)
2 IGNITION POWER (30A)
3 STOP LAMP
4 TAIL LAMP
5 REVERSE SIGNAL
6 LH TURN
7 RH TURN
8 AUX SWITCH #1 (IGN)
9 AUX SWITCH #2 (BATT)
13 AUX SWITCH #6 (DOWN)
14 AUX SWITCH #6 (UP)
15 PARK BRAKE
16 NEUTRAL SIGNAL
17 INDICATOR SWITCH (BODY LAMP)
18 (12v positive) PTO #1 – CA29

19 (12v positive) PTO #2 – CB7
20 (12v positive) SPEED CONTROL ON/OFF
21 BB J1939 +
22 BB J1939 -
23 (12v positive) SPEED CONTROL SET / DECEL
24 (12v positive) SPEED CONTROL RESUME / ACCEL
25 and 26 -
27 LH TURN / STOP
28 -
29 RH TURN / STOP
All Rights Reserved
Auxiliary Switch Locations (Cab)
W3099971
Connector Wire ID Description

1 IGN_SP111 Spare Ignition, Switch 4
2 - -
3 ILLUM_OPT Optional Illumination Connector
4 S026B Switch 3, Ignition
5 S026C Switch 4, Ignition
6 S026D Switch 5, Ignition
7 S027B Switch 6, Battery
8 ING_SP12 Spare Ignition, Switch 3
9 BAT_SP3 Spare Ignition, Switch 6
10 IGN_SP10 or BB_LP2 Spare Ignition, Switch 5
11 BB_LP_6SW_PLUG -
12 MISC_2 Output, Switch 3

1 If body builder wiring is specified, attach body builder wiring as follows: MISC_2 to BBSP_2, MISC_3 to BBSP_3, MISC_4 to BBSP_4, MISC_5 to BBSP_5,
MISC_6 to BBSP_6. Otherwise, band all MISC connectors behind ABC panel.
2 If body builder wiring is specified, attach body builder wiring as follows: MISC_2 to BBSP_2, MISC_3 to BBSP_3, MISC_4 to BBSP_4, MISC_5 to BBSP_5,
MISC_6 to BBSP_6. Otherwise, band all MISC connectors behind ABC panel.
All Rights Reserved
3 Connect spare ignition and battery connector to main cab harness as follows: IGN_SP12 to IGN_SP1 or IGN_SP9, IGN_SP11 to BAT_SP4, IGN_SP10 to IGN_
SP8 or BB_LP_PLUG, and BAT_SP3 to IGN_SP3.
Power Connections
Some judgement must be made for powering body equipment with the following trade-offs:
Ignition power – Will power off during engine crank which may cause faults or other effects if power supplies inputs used by
ECU’s on EMS power. May also be disconnected for low voltage disconnect.
EMS Connections – Available with key off but may effect starter performance or be affected by starter power fluctuations.
Battery Connections – Always available but will contribute to key off battery drain as well as effect, and be affected by, starter
as above.
W3113941
Fig. 12 Power Connections

Interrupted at ENGINE CRANK and LOW VOLTAGE DISCONNECT.
All Rights Reserved
W3085103
Fig. 13 DCL Conventional

Locations for the DCL Conventional are:
LR – Driver side of Main Cab Wiring Harness near Fuse and Relay center
TE / MRU – Mounted in the center electrical panel between the seats.
Conventional – Mounted under the ABS module taped to main harness.
DCL Conventional
PIN Circuit Number Circuit Function

A CA17 PTO 4/ CDS 2
B CB21 PTO 3 / CDS 1
C CB7;CB7B PTO 2
Spare Relay Control 2 (Controlled by
D CB16
VECU) CDS 2 out PTO 4
Spare Relay Control 1 (Controlled by
E CB18
VECU) CDS 1 out PTO 3
F F17A18 Ignition Bus Feed

G F18A EMS Power 1
H F17C3 Cruise SET/DECEL
J F17D3 Cruise RESUME/ACCEL
K N/A Not Used
All Rights Reserved
W3113946
Fig. 20 Conventional DCL Connections
Notes
All Rights Reserved
W3113945
Fig. 14 PTO & Engine Speed Control Connections

Note: Shaded area mDrive Dual PTO only.
All Rights Reserved
Conventional Auxiliary Switches
Conventional Trucks have the option to place dash switches connected to outputs in the outside body connector.
W3134380
Fig. 15 Conventional Auxiliary Switches
Notes
All Rights Reserved
W3113952
Fig. 16 Conventional — Reverse & Neutral Power
All Rights Reserved
Control Link II
TE / MRU and LR feature standard “Control Link II” body builder electrical connections. Control Link II consists of two
Deutsch HP-20 connectors, a 9-pin lighting connector along the frame rail, and a 29-pin electrical/electronic connector in-
cab, typically located above the engine tunnel body-in-white”.
W3084958
Fig. 17 Control Link II Components

1 Body Builder Cab Pass-Thru
2 29-pin Electrical/Electronic Connector
3 Refuse Body Builder Control Outputs
4 9-pin Lighting Connector
5 Body Builder Console (TE / MRU Only)
Order Codes for Body Connections (LCF Control Link II)
Item Sales Code Model Status Description

Control Link II Refuse 29-pin Cab & 9-pin
B830030 TE / MRU, LR Standard
System BOC Connections
Console Included w/
Body Builder Console M110003 TE / MRU Included
Control Link II
9-pin Back-of-Cab
Body Power Only B831018 TE / MRU Optional
Power & Lighting Only
Without Body Builder
No Connectors B830000 TE / MRU Delete Option
Quick Connections
Concrete Pumper Contact Sales
B831004/5/6/7 TE / MRU Optional
Connectors Engineering
All Rights Reserved
W3092642
Fig. 18 Body Builder Pass Through Area from Cab to Under Cab
1 Wiring Harness
2 Bracket
3 Cable Ties
4 Grommets
5 Screw
6 Electrical Gasket
W3092641
Fig. 19 Body Builder Pass Through Area from Cab to Under Cab
1 Clamps
2 Clamps
3 Chassis Clean Power
4 Chassis Body Builder
All Rights Reserved
Body Builder Connections
LR Control Link II
The body builder connector can be accessed by removing the panels on the center console. The suggested routing path for
upfitters is not a physical component provided with the vehicle. It’s purpose in the illustration is to indicate the suggested wir-
ing routes for upfitter harnesses. For convenience, MACK provides a pair of rubber grommets located behind the driver seat.
This is the pass-through area which leads beneath the cab.
W9096945
1 29-pin Body Builder Connector

2 9-pin Lighting Connector
3 Suggested Harness Routing for Upfitters
All Rights Reserved
W3064929
Fig. 20 Control Link II, 9-pin Lighting Connector, Wire Insertion Side of Connector
Pin Chart for Control Link II 9-pin Lighting Connector
Pole Wire ID Description

T F37B-3.0 Tail Lamp
Z F4D3–3.0 RH Turn
Y F33B-3.0 Stop Lamp
X F4C3–3.0 LH Turn
W F35B1–3.0 Clearance Lamp
V F34C-3.0 Neutral Power
U F34B2–5.0 Reverse Power
R XM1–13.0 Clean Ground
S F73A2–5.0 Clean Ground
Notes
All Rights Reserved
W3064928
Fig. 21 TE / MRU / LR / LEU Control Link II 29-pin Connector, Wire Insertion Side of Connector
Pin Assignments for TE / MRU / LR / LEU Control Link II 29-pin Body Builder Connector
Pole Wire ID Description

1 F39B–5.0 IGNITION POWER (30A)
2 FABA-5.0 BATTERY POWER (30A)
3 F40B1–3.0 IGNITION POWER (25A)
4 XABA-5.0 CLEAN GROUND
5 F42B1–1.0 REVERSE SIGNAL
6–11 - -
12 CA29–1.0 VMAC PTO# 1
13 CB7–1.0 VMAC PTO# 2
14 HA23–1.0 ENGINE RPM SIGNAL
TRANSMISSION TEMPERATURE
15 N164–0.8
SIGNAL
16 NA16–1.0 ECU GROUND
17 F18A1–1.0 IGNITION SIGNAL
18 N145NO-0.8 ALLISON #145 (12V)
19 X2A113–2.0 CAB GROUND
20 N143–0.8 ALLISON #143
21 DL5HB1–0.8 BBM J1939 (H)
22 DL5LB1–0.8 BBM J1939 (L)
23 N130NO-0.8 ALLISON # 130
24 N162–0.8 ALLISON # 162
25 N105-0.8 ALLISON # 105
26 N145B–0.8 ALLISON # 145
27 N103A-0.8 ALLISON # 103
28 N142A-0.8 ALLISON # 142
29 N117A-0.8 ALLISON # 117
All Rights Reserved
W3114392
Fig. 22 Body Builder Power & Ground LR Control Link II
Notes
All Rights Reserved
W3100110
DCL Connector (LR, TE / MRU) or Connector X21A (LR)
PIN Description
A Cruise ON/OFF Switch
B Spare SW.3 / PTO 3
C PTO 2
D VECU SW. Input
E Cruise ON/OFF Switch
F PTO 1
G Decel
H Accel
J EMS Power 1 CB18
K Spare Relay 2 / PTO 4
L Spare SW.2 / PTO 4
Spare Relay 1 / CDS 1 OUT / PTO 3
M
(TE / MRU Only; unused on LR)
N Signal Ground
P Ground
R Engine Stop/Spare Switch
All Rights Reserved
TE / MRU / LR DCL Connections
Figures 18 and 21 show DCL connections which are available on all Conventional models. Figures 16 and 22 show DCL con-
nections for TE / MRU / LR. The availability of these is limited as they are used for mDrive, ACC, Aux Fan and other options.
However, when available they can be used for more complicated controls such as secondary enable of engine speed control
or as configurable PTO output.
W3132814
Fig. 23 DCL Connector
All Rights Reserved
Allison Connections
TE / MRU / LR Control Link II has many Allison connections included. Conventional BodyLink does not. However, all trucks
with Allison Transmissions include a connector (X06D) to access Allison functions directly.
W3113943
Fig. 24 Allison Connections — TE / MRU, LR Control Link II

Note: * Shaded section on TE / MRU / LR only
Notes
All Rights Reserved
PTO and Engine Speed Control Connections
TE / MRU and LR have several specific wiring options for PTO that don’t necessarily affect engine speed control. However
the Control link II connection offers access to inputs to affect engine speed control based on PTO activation or other equip-
ment inputs.
W3113944
Fig. 25 PTO & Engine Speed Control Connections
All Rights Reserved
Lighting Connections
TE / MRU / LR Control Link II has lighting connections in a separate BOC connector whereas Conventional has lighting con-
nections in the Body Link connector which is also BOC. These are nominally lighting outputs but can also be used for control.
Note than Neutral and Reverse are also in the TE / MRU / LR Control Link II Connector.
W3114099
Fig. 26 Conventional Lighting Connections
Notes
All Rights Reserved
W3116272
Fig. 27 TE / MRU / LR Lighting Connections
Notes
All Rights Reserved
W3113951
Fig. 28 TE / MRU / LR Lighting Connections – Reverse and Neutral
All Rights Reserved
RP170A Refuse Related Chassis to Body Interface Connectors
W3136995
Fig. 29 RP170A Cab 31–Cavity Connector
Cavity Assignments for TE / MRU / LR / LEU 31-cavity Body Builder Connector
Cavity Wire ID Description

1 G02R1 (16ga) RPM
2 F24B1 (16ga) REV. SIGNAL
3 F17M3 (18ga) PTO#2
4 CB7 (18ga) PTO#1
5 DL5HB2 (18ga) BBM J1939H
6 DL5HL2 (18ga) BBM J1939L

7 CB21 (18ga) SPARE SW3/PTO#3
8 CA17 (18ga) SPARE SW4/PTO#4
9 F56A1 (16ga) IGN POWER
10 F17E4 (18ga) CRUISE CTRL ON/OFF
11 F17C1 (18ga) DECEL
12 F17D1 (18ga) ACCEL
13 BBA13A1 (18ga) PB SWITCH
14 - SPARE
15 N130CM3 (18ga) TRANS EMS POWER
16 N125 0.8mm, (18ga) SPEEDO
17 N103A (18ga) GROUND SIGNAL
18 N123 (18ga) SPLITSHAFT OR NEUTRAL AT
STOP
19 N143 (18ga) PTO REQUEST
All Rights Reserved
20 N122 (18ga) PUMP MODE TYPE
21 N142A (18ga) AUX. HOLD
22 N101 (18ga) RANGE INHIBITOR
23 N162 (18ga) RETARDER TEMP
24 N117A (18ga) AUTO NEUTRAL
25 N130NO (18ga) PTO ENABLE
26 N145B (18ga) RANGE INDICATOR
27 N105 (18ga) OVERSPEED INDICATOR
28 N164A (18ga) TRANS. TEMP
29 N145NO (18ga) NEUTRAL SIGNAL
30 F18A1 (18ga) IGN SIGNAL
31 - SPARE
All Rights Reserved
W3136996
Fig. 30 RP170A Chassis 14–Cavity Connector

A:1 X4B1 (6ga) GROUND TO FRAME
A:2 F34B2 (14ga) BACK UP
A:3 F5E4 (16ga) LEFT STOP TURN
A:4 F5D4 (16ga) RIGHT STOP TURN
A:5 F37B (14ga) TAIL/MARKER
A:6 F35B1 (14ga) CLEARANCE
A:7 F33B (14ga) STOP
A:8 - SPARE
A:9 - SPARE
A:10 - SPARE
A:11 - SPARE
A:12 - SPARE
A:13 F4C3 LEFT TURN
A:14 F4D3 RIGHT TURN
All Rights Reserved
W3136997
Fig. 31 RP170A Chassis 8–Cavity Connector

A F61A2 (12 GA) WIRE FED FROM CB61
(BATT+)
B F39A3 (12 GA) WIRE FED FROM CB11
C F47A2 (14 GA) WIRE FED FROM CB47

D FABA (12 GA) WIRE FED FROM A230A fuse
holder
E F34B11 (12 GA) WIRE FED FROM RLY62
(FRC2:J87)
F X1M2 (12 GA) WIRE FED FROM GROUND
X1_C2
G XABA (10 GA) WIRE FED FROM GROUND
STUD X136
H X2A39 (12 GA) WIRE FED FROM GROUND
X4_C2
Notes
All Rights Reserved
LR Workbrake
The Mack has a workbrake which operates pneumatically like a service brake. It is also tied into Allison inputs to effect a
forced neutral. The Allison also has some conditions to allow switching driving positions so that loss of throttle and transmis-
sion control don’t happen while moving.
W3113953
Fig. 32 LR Workbrake
Notes
All Rights Reserved
Summary
Figure 31 shows examples of what the control pins could be used for in an application. The PTO inputs are programmable
and can affect a conditional output, engine ramp, engine limits, etc. See programming section for details. Note that full safety
evaluation of the system should be carried out. I.E., adequate interlocks should be programmed or wired, so that the engine
will not accelerate in unintended situations. Interlocks can be done by powering switches using switched power (for example
neutral power) or by software parameters or both. For example, most applications should only have the engine ramp using
body controls when the park brake is on and the transmission is in neutral. Exceptions should be carefully considered..
W3113957
Fig. 33 Example TE / MRU showing Body Builder supplied wiring for Controls
Notes
All Rights Reserved
General
Wiring J1939
Mack doesn’t necessarily recommend or condone tapping into the J1939 databus. This is the main control buss and even de-
vices only listening can improperly load the line and cause communication problems. The signals are fast enough that they
are affected by the physics of the electrical charges traveling through the lines. So it matters how the device is designed and
where it is placed in relation to other devices. However this method can save wiring and gives the body builder more flexibility
and control in developing applications. To that end the following information is provided. However, it is recommended appli-
cations be implemented with sufficient field testing to uncover any problems.
Here are two ways to properly connect to J1939 without damaging the cab harness.
1. Connect at the diagnostic connector.

The diagnostic port contains J1939 lines mainly for temporary connection for diagnostic tools. Since it also contains power
and ground for diagnostic tools, it is a convenient choice for connection of control and monitoring devices. However, note that
J1939 specifies one device per node. So, it would be incorrect to place two devices there.
2. Add the device at the terminating resistor.

The terminating resistor for the main CAN bus is found in the dash. This method effectively lengthens the “backbone” of the
main can line and adds a node. To do this the body builder would make a “T” harness to insert between the terminating resis-
tor and it’s connector (see figure). Theoretically, more than one node could be placed this way. However, some trucks are al-
ready at or near the theoretical limit
Mack follows SAE J1939-15 meaning it uses an unshielded, twisted pair and is theoretically limited to 10 devices.
W3083536
Fig. 34 Adding a Node at the Terminating Resistor

* To Truck
All Rights Reserved
The following parts can be used in the above “T” harness. Critical is that only two terminating resistor remain on the network
(one is in the ECM). It may also be possible to have one terminating resistor in the aftermarket device if it is replacing the ter-
minating resistor.
T Harness Part Numbers
T Harness
Abbreviation Connector Part Number (New) Part Number (Old)
MACK # Delphi # MACK # Deutsch #

Cab Harness Ter-
CHTRC minating Resistor 21430472 13510085 3187784 DTM04-2P
Connector
Cab Harness Ter-
DTM06-2S-
CHTR minating Resistor 21430457 15429045 25171700
P006
120 Ω
Connection to Cab
20500398 13510099 3187782 DTM06-2S
harness
AD Aftermarket Device N/A N/A N/A
MC Mating Connector N/A N/A N/A
Body Builder
BBI N/A N/A N/A
Installed
Notes
All Rights Reserved
Another more convenient way to connect to J1939 (or J1587) is through the diagnostic connector.
9-pin Diagnostic Connector
W9000628
Fig. 35 9-pin Diagnostic Connector

Note: Export Engines Only

PIN Definition
A Ground
B Battery
C CAN H (J1939 H-Yellow)
D CAN L (J1939 L-Green)
E Not used (Shield)
F J1587 +
G J1587 –
H Not Used
J Ignition + (Key Switch)
All Rights Reserved
W3085011
Fig. 36 16-pin Diagnostic Connector (OBD 13)
16-pin Diagnostic Connector (OBD 13) Pin Allocation
16-pin Diagnostic Connector (OBD 13 SAE J1962-Type A Connector)

PIN Definition
OEM discretionary (assigned as: Key switch – ignition signal for
1
AM tool)
2 (Not Used)
3 OEM discretionary (assigned as: SAE J1939-15_CAN_H)
4 Chassis ground
5 Chassis ground
6 CAN_H line of ISO
7 (Not Used)
8 (Not Used)
9 (Not Used)
10 (Not Used)
11 OEM discretionary (assigned as: SAE J1939-15_CAN_L)
12 OEM discretionary (assigned as: SAE J1587 positive)
13 OEM discretionary (assigned as: SAE J1587 negative)
14 CAN_L line of ISO
15 (Not Used)
16 Battery positive voltage
All Rights Reserved
Serial Communications and Programming Abbreviations
Acronym Description
ACM Aftertreatment Control Module
BBM Body Builder Module
CAN Controller Area Network
CDS Customer Defined Statement
DCL DataMax Control Language
ECC/MCC Electronic Climate Control/ Manual Climate Control
ECM Engine Control Module
EHT Electronic Hand Throttle
ECS Electronic Speed Control
FMI Failure Mode Identifier
GSECU Gear Selector ECU
LCM Light Control Module
NOx Nitrogen Oxide
PGN Parameter Group Number (J1939)
PID Parameter Identification (J1587)
PTO Power Take-Off

SA Source Address (J1939 Sender)
SCU Satellite Control Unit (Qualcomm)
SID Subsystem Identification (J1587)
SPN Suspect Parameter Number (J1939)
SRS Supplemental Restraint System
SSC Single Speed Control
TCM Transmission Control Module
TPM Tire Pressure Monitor
VCADS Vehicle Computer Aided Diagnostic System (service tool)
VDA Vehicle Data Administration (OEM database)
VECU Vehicle ECU

Vehicle Management and Control (Mack’s electrical
V-MAC
architecture)
All Rights Reserved
Data Link System
This section provides information on the design and function of the vehicle communications data links. These communication
links are based on SAE J1587, J1708 and J1939 Recommended Practices and the ISO 14229 Standard. For more specific
information about the ISO 14229 Standard, please refer to the ISO website (www.iso.org).
The data links are used to relay shared vehicle information between control modules and diagnostic, service and (in the case
of onboard diagnostic (OBD) information) scan tools. The three datalink types used are SAE J1939, SAE J1587/J1708 and
ISO 14229.
SAE J1939
SAE J1939 is a communications link between stand alone vehicle modules. This data link is commonly referred to as the
“Control Data link”.
It is used primarily to transmit control signals that are shared between other stand alone modules. The information on the
SAE J1939 control link is used for control functions. Fault messages or diagnostic information also transmits across this link.
These control signals may be for, engine, transmission, brakes or a number of other vehicle control needs.
The J1939 operates at 250,000 bits per second which is approximately 26 times faster then the J1708/1587 data link. This
higher speed allows the system to operate at a faster sampling rate and higher resolution, thus being more capable of provid-
ing better control of vehicle functions.
The J1939 data link consists of a pair of 18 gauge unshielded twisted wires. The designations of the networks are CAN_H
and CAN_L. The designation of the individual wires are DL1H which is yellow and DL1L which is green. The nominal rate of
twist required is 0.89 twists per 25.4 mm (1 inch) or 33 twists per meter (3.28 feet). This twist helps protect against electrical
interference.
The J1939 data link is electrically terminated at each end with a load resistor, which is commonly referred to as a termination
resistor. Each J1939 network has two termination resistors associated with it. Only two termination resistors are allowed with-
in a network. The termination resistor can be located external as part of the wiring harness, or integrated internally in the
ECM. Any ECM that does not contain the termination resistor is referred to as a Type I, and an ECM that contains the termi-
nation resistor is referred to as a TYPE II. The correct number of termination resistors can be easily checked by measuring
the resistance across cavities C and D of the 9-pin diagnostic connector or across cavities 3 and 11 for the 16-pin diagnostic
connector. The correct resistance is 50 – 70 ohms. The terminating resistors should each have a resistance of 110 – 130
ohms when tested individually.
Note: It is important to remember which control units the vehicle is equipped with and which fault codes are stored in each
control unit.
Do not splice into a V-MAC, ABS/ATC or any other electronic control unit harness.
Note: Do not cut or tap into the J1939 green/yellow twisted wires or any other wire or harness used on this vehicle.
Use the provided connectors, and only add approved J1939 components with validated software. Failure to comply
may result in personal injury or equipment damage. Any cutting. splicing, alteration or modification to the wiring
will Void the Mack Trucks Warranty on the Electrical System.
All Rights Reserved
ISO 14229
Note: ISO 14229 only applies to vehicles with MACK engines.
ISO 14229 is the Powertrain control link. The ISO is used for programming between the ECM, ACM and TCM. It is used pri-
marily to transmit control signals that are shared between other stand alone modules. The information on the ISO 14229 con-
trol link is used for control functions. Fault messages or diagnostic information also transmits across this link. These control
signals may be for engine, transmission and aftertreatment ECUs.
The ISO 14229 operates at 500,000 bits per second. This higher speed allows the system to operate at a faster sampling
rate and higher resolution, thus being more capable of providing better control of vehicle functions.
The ISO 14229 data link consists of a pair of 18 gauge unshielded twisted wires. The designations of the networks are CAN_
H and CAN_L . The designations of the individual wires are DL2H and DL2L which are both white with orange stripes. The
nominal rate of twist required is 40 twists per meter (3.28 feet). This twist helps protect against electrical interference.
The ISO 14229 data link is electrically terminated at each end with a load resistor, which is commonly referred to as a termi-
nation resistor. Each ISO 14229 network has two termination resistors associated with it. Only two termination resistors are
allowed within a network. The termination resistor can be located external as part of the wiring harness, or integrated inter-
nally in the ECU/ECM. Any ECU/ECM that does not contain the termination resistor is referred to as a Type I, and an ECU/
ECM that contains the termination resistor is referred to as a TYPE II. The correct number of termination resistors can be
easily checked by measuring the resistance across cavities 3 and 11 for the 16-pin diagnostic connector. The correct resist-
ance is 50 – 70 ohms. The terminating resistors should each have a resistance of 110 – 130 ohms when tested individually.
Note: It is important to remember which control units the vehicle is equipped with and which fault codes are stored in each
control unit.
SAE J1708/1587
Note: MACK engines and mDrive transmissions do not include the J1587 / J1708 datalink.
SAE J1708/1587 is a communications link between stand alone vehicle modules. This data link is commonly referred to as
the “Information Data link”. It is used primarily to transmit shared information between these stand alone modules. Fault mes-
sages or diagnostic information also transmits across this link. The J1708/1587 exchanges information with a data bus speed
of 9600 bits per second. The J1708 defines parameters that relate primarily to hardware and basic software compatibility.
The J1587 defines the actual data to be transmitted by particular modules. The J1587/1708 data link consists of a pair of 18
gauge twisted wires. The nominal rate of twist required is 1 twist per 25.4 mm (1 inch) or 40 twists per meter (3.28 feet). This
twist helps protect against electrical interference. A fault in this data link can affect the transfer of information, and can make
it difficult to communicate with the source in order to carry out tests using VCADS (found in the Premium Tech Tool or PTT).
An indication that there is a problem with SAE J1708/1587 can be that faults from a certain control unit can not be corrected,
erased or reset.
Data Link Faults
W3005017
Whenever a data link fault is present, refer to Guided Diagnostics found in the manufacturer's scan tool (Premium Tech Tool
or PTT) for diagnostic information.
Note: The ISO 14229 does not have FMIs. Instead this data link has failure type bytes (FTBs).
• The type of FMI/FTB that an individual electronic control unit (ECU) can monitor is dependent on the software in the ECU.
All FMIs/FTBs cannot be recognized by all ECUs.
• The ECU reporting the diagnostic trouble code (DTC) may not be the ECU that is involved at the site of the specific failure.
For example, The engine control module (ECM) may report a data link fault that is actually at the vehicle electronic control
unit (VECU). The VECU would not be able to report if the data link is broken between the VECU and data link backbone.
All Rights Reserved
Datalink Topology
US2010 Emissions Engine plus OBD2013
W3084851
Acronym Description
ECM Engine Control Module
ACM Aftertreatment Control Module
NOx Nitrogen Oxide
GSECU Gear Selector ECU
TCM Transmission Control Module
DEF Diesel Exhaust Fluid
ACC Active Cruise Control
VECU Vehicle ECU
ABS Anti-Lock Braking System
BBM Body Builder Module
SCU Satellite Control Unit (Qualcomm)
All Rights Reserved
Termination Resistor
W3005518
Termination Resistor, 2–pin
Termination Resistor – J1939

Termination resistors are wired to each end of the SAE J1939 data link to prevent signal reflections. They must remain con-
nected for the data link to function properly. The resistance value of each termination resistor is 110–130 Ω. When properly
installed in the data link, their combined resistance is 50–70 Ω since they are connected in parallel.
The termination resistor at one end of the SAE J1939 data link is located in the fuse/relay center (FRC) near the vehicle elec-
the termination resistor at the engine end is located inside the ECM. On vehicles equipped with Cummins engine, the termi-
nation resistor is located in the harness area just outside of the ECM.
A SAE J1939 data link connection is located at the transmission area in the chassis harness. On vehicles equipped with an
more than two resistors exist in the SAE J1939 data link circuit, incorrect or absent signals may occur. You can easily check
to see if you have two resistors by measuring the resistance between pin C and D for the 9-pin diagnostic connector, or pin 3
and 11 for the 16-pin diagnostic connector, with the ignition key in OFF position. The correct resistance is 50 – 70 Ω. The ter-
mination resistors should each have a resistance of 110 – 130 Ω when tested individually.
Termination Resistor – ISO 14229

Termination resistors are also wired for the ISO 14229 data link. One resistor is located in the engine control module (ECM).
The other is a two pin resistor located in the dash close to the diagnostic connector. The diagnostic connector is located on
the driver’s side lower dash panel. Termination resistors must remain connected for the data link to function properly. The re-
sistance value of each termination resistor is 110–130 Ω. When properly installed in the data link, their combined resistance
is 50 – 70 Ω since they are connected in parallel
The termination resistor at one end of the ISO 14229 data link is located in the fuse/relay center (FRC) near the vehicle elec-
the termination resistor at the engine end is located inside the ECM.
A ISO 14229 data link connection is located at the transmission area in the chassis harness. On vehicles equipped with an
more than two resistors exist in the ISO 14229 data link circuit, incorrect or absent signals may occur. You can easily check
to see if you have two resistors by measuring the resistance between pin 3 and 11 for the 16-pin diagnostic connector, with
the ignition key in OFF position. The correct resistance is 50 – 70 Ω. The termination resistors should each have a resistance
of 110 – 130 Ω when tested individually.
All Rights Reserved
0802013 Electrical System Version 3 Parameters
Parameter List
Group DOID Parameter Caption Description
Cruise Control AI AI Cruise Control Max The maximum speed that can be
Speed set in the cruise control.
Engine Fan P1I2F FTX Fan Enable With This flag will enable the fan with
Controls Engine Brake the engine brake. 0 = Disabled, 1
= Enabled
Engine Governor P1I03 AZQ High Idle Governor Engine speed where the gover-
For HiIgh Gears nor output crosses the max tor-
que curve. Used for high gear
ratios.
P1I04 AZO High Idle Enable If this flag is set to TRUE, it is
Flag For Low Gears possible to use a higher end gov-
ernor engine speed for low
gears.
P1I05 AZR High Idle Gear Ratio Gear ratio for the gear P1I03 set-
For Low Gears ting should be used. For higher
gears the end governor speed is
used.
P1I18 AZS High Idle Ratio For Gear ratio for the gear where end
High gears governor engine speed is used.
For lower gears the P1I03 setting
should be used.
Engine Idle P1F9W YA Engine Idle, Target Target engine speed at idle.
Settings Speed
Engine Protection P1I19 FVS Customer Shut Customer shut down status, 0 =
Down For Oil No action, 1 = Forced idle, 2 =
Pressure Shut off engine
P1I17 FVU Customer Shutdown Customer shut down status, 0 =
For Coolant Level No action, 1 = Forced idle, 2 =
Shut off engine
P1I2B FVY Customer Shutdown Customer shut down status, 0 =
For Transmission No action, 1 = Forced idle, 2 =
Temperature Shut off engine
P1I2A GHA Customer Shutdown Customer shut down status, 0 =
For Oil Temperature No action, 1 = Forced idle, 2 =
Shut off engine
P1I18 FVW Customer Shutdown Customer shut down status, 0 =
For Coolant No action, 1 = Forced idle, 2 =
Temperature Shut off engine
Engine Speed P1ANA AU Max Engine Speed Maximum engine speed allowed
Limit Stationary when the vehicle is stationary.
The maximum engine speed
varies between approximately
1200 - 2600 rpm depending on
engine type.
All Rights Reserved
P1I04 AZO High Idle Enable If this flag is set to TRUE, it is
Flag For Low Gears possible to use a higher end gov-
ernor engine speed for low
gears.
P1IDB BNQ Max Engine Speed Specifies the max engine speed
with a Vehicle when a vehicle speed error is
Speed Error active.
Engine Torque P1JED JAA PTO Through Drive- Configures if PTO is enabled
Limit shaft, Enables through driveshaft. If set to 1, tor-
que limit for low vehicle speed is
deactivated. 0 = Disable ,
1 = Enable
Injection Control P1AM4 ATJ Injector Cylinder 1, The new trim code must be pro-
Calibration grammed after replacing the unit
injector. The trim code (T/C) is
P1AM5 ATK Injector Cylinder 2,
shown on the injector label and
Calibration
consists of up to 9 characters.
P1AM6 ATL Injector Cylinder 3,
Calibration
P1AM7 ATM Injector Cylinder 4,
Calibration
P1AM8 ATN Injector Cylinder 5,
Calibration
P1AM9 ATO Injector Cylinder 6,
Calibration
P1G3E IVT & JAN Injector Perform- Reset has to be done after injec-
ance Log tor change, by using the routine
control: R1AFI - Reset of Target
Torque Reference Value
Miscellaneous P1I15 AIZ Fuel Consumption, A percentage correction value to
Engine Settings Calibration In compensate any deviation be-
Percent tween the calculated fuel con-
sumption shown in the Driver
Information Display and the fuel
consumption according to the
customer's fuel protocol.
P1AOF DX Gust Data, Engine Password to allow changing of
ECU Password parameter values on this vehicle.
If a password is in place, correct
entry of the password will be re-
quired when changing parameter
values.
P1IEA JZF Smart Torque, Enables the Smart Torque
Enable function
P1IRK MYD Accelerator Limiter, Enables the Accelerator Limiter
Enable function. 0 = Disabled, 1 =
Enabled
P1I07 9G Diff RSL, Transmis- The gearbox ratio in the highest
sion Ratio Highest gear. The ratio can be found in
Gear the gearbox specifications. The
All Rights Reserved
ratio must be entered in order for
the control module to calculate
which gear is selected.
Miscellaneous P1I08 9H Diff RSL, Transmis- Gearbox ratio second highest
Engine Settings sion Ratio Next gear.
Highest Gear
P1AOD DV Diff RSL, Max Speed limitation when the sec-
VSPD Next Highest ond highest gear is selected. The
Gear value must be lower than param-
eter P1AOC. Do not use with
AMT gearboxes.
P1AL0 AJ Diff RSL, Enable / Activating different speed limita-
Disable tions when driving in the highest
or second highest gear. This
function is used if the maximum
speed can only be reached when
the highest gear is engaged. Pa-
rameters P1AOD, P1ALW/P1I07
and P1ALX/P1I08 must be pro-
grammed if this function is acti-
vated. 0 = Disabled, 1 = Enabled
Miscellaneous P1HUB FTM Soft Cruise Enable Enable the soft cruise functional-
Vehicle Settings ity. 0 = FALSE, 1 = TRUE
which gear is selected
P1IP6 DN Customer Data Customer Data Fleet Identifier =
Fleet Identifier "Fleet ID" = "Unit Number" : The
Customer Fleet Identifier can be
set via the cluster menu by the
customer.
P1APZ IEH Transmission Kick- This parameter defines when the
down Mode Kick-down function is available.
P1ARH IPA Number of Reverse Setting determines the number
Gears of reverse gears available
P1ASL LAQ Highest Start Gear The adjustment of start gear in
in Manual Mode manual mode will be restricted to
gears equal to or lower than this
value.
P1ASM LAR Highest Start Gear The selection and adjustment of
in Automatic Mode start gear in automatic mode will
be restricted to gears equal to or
lower than this value.
P1FP0 NXK Enable Splitbox False = Splitbox started when
Start with Accelera- the gear lever moved from Neu-
tor Pedal tral to Automatic or Manual. True
= The splitbox is not started until
All Rights Reserved
also the accelerator pedal is de-
pressed. This will provide addi-
tional torque backup for the
splitbox start.
P1FP2 NUO Enable I-Roll Only True = I-Roll will only be allowed
When Cruise Con- when CC is active. False = I-roll
trol (CC) Active allowed both for pedal- and
cruise control driving
Miscellaneous P1IK3 MUF Highest Adjustable The highest adjustable gear in
Vehicle Settings Gear in Manual manual mode. If gear lever is
Mode moved to manual in a higher
gear than highest adjustable
gear in manual, no manual ad-
justments will be allowed. The
function prohibits the driver to
drive on a too low gear, which will
increase fuel consumption. This
is only valid in economy mode.
P1IZ5 PPQ Transmission Auto- Enables the driver to manually
matic Pedal Gear adjust the automatic selected
Enable Manual driving gear with gear selection
Adjustment +/- buttons when the accelerator
pedal is depressed.
P1G42 JSI Minimum DPF In- Minimum road speed limit (RSL)
hibit Target Speed during DPF inhibit.
Limit
VINNO VIN Vehicle Identifica- 17 character VIN Number.
tion Number
P1AOD DV Diff RSL, Max Speed limitation when the sec-
AMT gearboxes.
P1AL0 AJ Diff RSL, Enable / Activating different speed limita-
Disable tions when driving in the highest
Power Take Off #1 P1AO5 GJG Split Gear for Trans- Split gear used when transmis-
(PTO 1) mission PTO1 sion PTO1 is engaged. Low split
has priority over high split if
PTO1 and PTO2 are both en-
gaged and have conflicting (split
gear) settings.
Power Take Off #2 P1AO6 GJH Split Gear for Trans- Split gear used when transmis-
(PTO 2) mission PTO2 sion PTO2 is engaged. Low split
All Rights Reserved
has priority over high split if
PTO1 and PTO2 are both en-
gaged and have conflicting (split
gear) settings.
Road Speed Limit P1AOD DV Diff RSL, Max Speed limitation when the sec-
AMT gearboxes.
P1AOC DP Customer Road Specifies the customer select-
Speed Limit able maximum speed the vehicle
can operate on level road. The
vehicle speed will be limited by
the lowest of the following: Cus-
tomer Road Speed Limit
(P1AOC), Road Speed Limit
(P1ALV) and Secondary Road
Speed Limit (Request via CAN-
signal from Body Builder Module)
if available. For markets that use
performance bonus: Any addi-
tional speed granted by the Per-
formance Bonus feature will be
added to the Customer Road
Speed Limit (P1AOC) value, as
(so) long as the overall maximum
of 140km/h (87 MPH) is not ex-
ceeded. Any speed penalty im-
posed by the Differential Road
Speed Governor will be sub-
tracted from this maximum value.
Max Cruise Control Speed must
be set less than or equal to the
accelerator-pedal maximum
specified by the Customer Road
Speed Limit (P1AOC) value.
P1I01 FTP RSL Enable Soft Enable the soft cruise functional-
Cruise Functionality ity for RSL (Road Speed Limit). 0
= Not enabled, 1 = Enabled
Road Speed Limit P1AL0 AJ Differentiated RSL, Activating different speed limita-
Enable tions when driving in the highest
AI AI Cruise Control Max The maximum speed that can be
Speed set in the cruise control
All Rights Reserved
which gear is selected.
P1I08 9H Diff RSL, Transmis- Gearbox ratio second highest
sion Ratio Next gear.
Highest Gear
P1I09 9D Road Speed Limit The maximum vehicle speed. In
Maximum certain countries the maximum
speed is determined by legal
requirements
P1I16 PPE Road Speed Limit The pedal vehicle speed limit
With Pedal which is used to set a higher or
lower pedal vehicle speed. Its in-
tended to be used together with
Road speed limit function to
make the driver want to use
cruise control.
P1G42 JSI Minimum DPF In- Minimum road speed limit (RSL)
hibit Target Speed during DPF inhibit.
Limit
Fuel Economy P1I0G ADZ Performance Bonus Enables the Performance Bonus
Incentive Program Enable feature. 0 = Disabled, 1 =
Enabled
P1I0H ADX Performance Bonus Specifies the fuel consumption
Fuel Target [km/l] target value for the Per-
formance Bonus function.
P1I0I FXA Performance Bonus Specifies the penalty target value
Fuel Penalty Target for fuel consumption [km/l]. Be-
low this target value the driver
will lose speed as a penalty.
P1I0J ADY Performance Bonus Specifies the percentage value
Idle Target for Idle time below which the driv-
er gets a performance bonus.
P1I0K FWX Performance Bonus Specifies the amount of time the
Sweet Spot Target driver must spend in the sweet
spot to get a performance bonus.
P1I0N FWY Performance Bonus Sets the Performance Bonus
Function Mode function mode.
0 = Bonus, 1 = Penalty, 2 = Bo-
nus and Penalty
P1I0L FWZ Performance Bonus Sets the Performance Bonus
Parameters running mode:
0 = No targets, 1 = Fuel, 2 = Idle
P1I0M BTR Performance Bonus Specifies the number of steps for
Number of Steps the Performance Bonus. There
are 1-3 steps
All Rights Reserved
P1I0P AEB Performance Bonus The delta value to adjust the cus-
Vehicle Speed tomer vehicle speed limit for the
Bonus Performance Bonus function.
Fuel Economy P1I0Q FXD Performance Bonus The delta value to decrease the
Incentive Program Vehicle Speed customer vehicle speed limit with
Penalty during penalty for the Perform-
ance Bonus function.
P1AP3 IEO Transmission Per- 0 = "Manual" = Performance
formance Mode mode available.
1 = "Auto" = Performance mode
available. The transmission will
automatically return to Economy
mode when the engine is no lon-
ger operating under high load.
2 = "Disable" = Performance
mode not available"
P1IK0 IHL Performance Bonus Enables the Kick-Down and /or
II - Enable K-D and the Performance mode only
P as Reward when the driver is rewarded by
Performance Bonus II. This fea-
ture requires that at least one of
the parameters P1AP3, (Enable
Performance Mode) and P1APZ,
(Enable Kick-Down) are enabled.
Fuel Economy P1IK1 IEG Transmission I-Roll Enable the transmission free
Incentive Program Function Enabled wheeling function I-Roll
P1IK2 IEK Lowest I-Roll Gear The lowest gear in which the I-
Roll function is enabled
P1I53 ADV Performance Bonus The effective distance, all mean
Effective Distance values relates to this distance.
P1JGX NXI Vehicle Mass Esti- 1 = Scales the weight for Vehicle
mation Eco Level Mass Estimation via the Eco Lev-
Enabled el Map.
0 = Eco Level Map not used for
Vehicle Mass Estimation. Vehicle
Mass Estimation will not work
without this value set to 1!
P1INE PDM Eco Level Used in Forced Eco Level used in
SoftCruise Function SoftCruise function.
All Rights Reserved
Supported SAE J1939 Serial Messages
Note: Mack does not recommend broadcasting on the databuss. However, it is known that there are devices on the market
which effect an engine speed control.
Mack broadcasts the following with message and signal definition per SAE J1939-71. Exceptions noted. Dates are build
dates rather than model year. Most changes correspond with emissions regulation.
SAE J1939 Messages
SAE J1939 Messages

Source
PGN Message Name SPN Signal Name Usage Notes
Address
65198 Air Supply Pressure 23 1087 Service Brake Circuit 1 Conven-
Air Pressure tional
Since
1088 Service Brake Circuit 2
2007
Air Pressure
46 Pneumatic Supply
Pressure
65269 Ambient Conditions 0, 17, 23 171 Ambient Air SA 23 23 – Sen-
Temperature Since sor Source
2007 &
SA 0,17
since
2010
0 108 Barometric Pressure Since
2007
172 Engine Air Intake
Temperature
64891 Aftertreatment 1 Service 0 3719 Aftertreatment Diesel Since
Particulate Filter 1 Soot 2007
Load Percent
3720 Aftertreatment Diesel
Particulate Filter 1 Ash-
Load Percent
65110 Aftertreatment 1 SCR 0 1761 Aftertreatment 1 SCR Since
Reagent Tank 1 Catalyst Tank Level 2010
Information
3517 Aftertreatment 1 SCR
Catalyst tank Level 2
5245 Aftertreatment 1 DEF
Tank Low Level Indicator
5246 Aftertreatment SCR Op-
erator Inducement
Severity
64946 Aftertreatment 1 0 3251 Aftertreatment 1 Diesel Since
Intermediate Gas Particulate Filter Differ- 2007
ential Pressure
64947 Aftertreatment 1 Outlet 0 3246 Aftertreatment 1 Diesel Since
Gas 2 Particulate Filter Outlet 2007
Gas Temperature
All Rights Reserved
SAE J1939 Messages
Source
Address
64948 Aftertreatment 1 intake 0 3242 Aftertreatment 1 Diesel Since
Gas 2 Particulate Filter Intake 2007
Gas Temperature
65265 Cruise Control/Vehicle 17 84 Wheel Based Vehicle All
Speed Speed
86 Cruise Control Set
Speed
595 Cruise Control Active
596 Cruise Control Enable
Switch
597 Brake Switch
598 Clutch Switch
599 Cruise Control Set
Switch
600 Cruise Control Coast
(Decelerate) Switch
601 Cruise Control Resume
Switch
602 Cruise Control Acceler-
ate Switch
976 PTO Governor State Reflects
engine
speed
control
state not
PTO input
or output
state.
527 Cruise Control States
70 Parking Brake Switch
57344 Cab Message 1 23 3695 Diesel Particulate Filter Since
Regeneration Inhibit 2007
Switch
3696 Diesel Particulate Filter
Regeneration Force
Switch
1856 Seat Belt Switch Since
2010
65276 Dash Display 23 96 Fuel Level 1 Since
2007
65226 DM1 0 Since
2007
64952 DM26 0 Since
2010
All Rights Reserved
SAE J1939 Messages
Source
Address
64892 Diesel Particulate Filter 0 3697 Diesel Particulate Filter Since
Control 1 Lamp Command 2007
3698 Exhaust System High
Temperature Lamp
Command
Passive Regeneration
Status
Active Regeneration
Status
Status
Active Regeneration In-
hibited Status
hibited Due to Inhibit
Switch
hibited Due to PTO
Active
hibited Due to Accelera-
tor Pedal Off Idle
hibited Due to Vehicle
Speed Above Allowed
Speed
hibited Due to Parking
Brake Not Set
hibited Due to Low Ex-
haust Gas Temperature
hibited Due to System
Fault Active
64892 (cont.) Diesel Particulate Filter 0 3714 Diesel Particulate Filter Since
Control 1 Active Regeneration 2007
All Rights Reserved
SAE J1939 Messages
Source
Address
Inhibited Due to Tempo-
rary System Lockout
hibited Due to Perma-
nent System Lockout
hibited Due to Engine
Not Warmed Up
3698 Exhaust System High
Temperature Lamp
Command
61441 Electronic Brake 11 561 ASR Engine Control Per ABS
Controller 1 Active type
562 ASR Brake Control Per ABS
Active type
563 Anti-Lock Braking (ABS)
Active
1121 EBS Brake Switch Not Used
521 Brake Pedal Position Not Used
575 ABS Off-road Switch Per ABS
type
576 ASR Off-road Switch Per ABS
type
577 ASR "Hill Holder" Switch With I-
shift/
mDrive
1238 Traction Control Over- Per ABS
ride Switch type
1243 ABS Fully Operational
1438 ABS/EBS Amber Warn-
ing Signal (Powered
Vehicle)
1793 ATC/ASR Information Per ABS
Signal type
1481 Source Address of Con- Per ABS
trolling Device for Brake type
Control
1836 Trailer ABS Status Per ABS
type
1792 Tractor-Mounted Trailer Per ABS
ABS Warning Signal type
All Rights Reserved
SAE J1939 Messages
Source
Address
65215 Wheel Speed Information 11 904 Front Axle Speed All
905 Relative Speed; Front
Axle, Left Wheel
906 Relative Speed; Front
Axle, Right Wheel
907 Relative Speed; Rear
Axle #1, Left Wheel
Axle #1, Right Wheel
Axle #2, Left Wheel
Axle #2, Right Wheel
64964 Electronic Brake 11 2912 Hill holder mode With Ish-
Controller 5 ift/mDrive
61444 Electronic Engine 0 899 Engine Torque Mode All 20 ms
Controller 1 fixed rate
512 Driver's Demand Engine
- Percent Torque
513 Actual Engine - Percent
Torque
190 Engine Speed
1483 Source Address of Con-
trolling Device for En-
gine Control
1675 Engine Starter Mode
61443 Electronic Engine 0 558 All
Controller 2
91 Accelerator Pedal Posi- from SA
tion 1 17 with
Cummins
92 Engine Percent Load At
Current Speed
65247 Electronic Engine 0 514 Nominal Friction - Per- All
Controller 3 cent Torque
64981 Electronic Engine 2791 Engine Exhaust Gas Re- Since
Controller 5 circulation 1 (EGR1) 2007
Valve Control
2795 Engine Variable Geome- All
try Turbocharger (VGT)
1 Actuator Position
65263 Engine Fluid 0 94 Engine Fuel Delivery All
Level/Pressure 1 Pressure
98 Engine Oil Level
All Rights Reserved
SAE J1939 Messages
Source
Address
100 Engine Oil Pressure
101 Engine Crankcase
Pressure
111 Engine Coolant Level
65251 Engine Configuration 1 0 30 bytes
61440 Electronic Retarder 0,15 900 Retarder Torque Mode SA 15 be-
Controller 1 fore 2007
520 Actual Retarder - Per-
cent Torque
65262 Engine Temperature 1 110 Engine Coolant All
Temperature
174 Engine Fuel Tempera-
ture 1
175 Engine Oil Temperature
1
61442 Electronic Transmission 3 161 Transmission Input Shaft Automat-
Controller 1 Speed ed trans-
missions
560 Transmission Driveline
Engaged
573 Transmission Torque
Converter Lockup
Engaged
574 Transmission Shift In
Process
4816 Transmission Torque
Converter Lockup Tran-
sition in Process
191 Transmission Output SA 17 with
Shaft Speed Cummins
522 Percent Clutch Slip
606 Engine Momentary
Overspeed Enable
607 Progressive Shift
Disable
5015 Momentary Engine Max-
imum Power Enable
61445 Electronic Transmission 3 524 Transmission Selected Automat-
Controller 2 Gear ed trans-
missions
523 Transmission Current
Gear
526 Transmission Actual
Gear Ratio
All Rights Reserved
SAE J1939 Messages
Source
Address
65134 High Resolution Wheel 11 1592 Front Axle, Left Wheel Since
Speed Speed 2007
1593 Front axle, right wheel
speed
1594 Rear axle, left wheel
speed
1595 Rear axle, right wheel
speed
65270 Intake/Exhaust 0 173 Engine Exhaust Gas Since
Conditions 1 Temperature 2007 SA
23 from
2004-
2007
102 Engine Intake Manifold Since
#1 Pressure 2007
105 Engine Intake Manifold 1
Temperature
106 Engine Air Intake
Pressure
107 Engine Air Filter 1 Differ-
ential Pressure
65266 Fuel Economy (Liquid) 0 183 Engine Fuel Rate Since
2007
184 Engine Instantaneous
Fuel Economy
185 Engine Average Fuel
Economy
65254 Time/Date 23 959 Seconds All
960 Minutes UTC/GMT
961 Hours UTC/GMT
962 Day
963 Month
964 Year
1601 Local minute offset Display
clock
1602 Local hour offset Display
clock
65272 Transmission Fluids 1 3 177 Transmission Oil Automat-
Temperature ed Trans-
missions
0 Torque/Speed Control 1 3,11,17,42,2- 695 Engine Override Control By op-
30 Mode tions –
engine
898 Engine Requested
brake,
Speed/Speed Limit
All Rights Reserved
SAE J1939 Messages
Source
Address
518 Engine Requested Tor- transmis-
que/Torque Limit sion, etc.
61449 Vehicle Dynamic Stability 11 1807 Steering Wheel Angle Trucks
Control 2 with
1808 Yaw Rate
stability
1809 Lateral Acceleration control
1810 Longitudinal
Acceleration
1811 Steering Wheel Turn
Counter
1812 Steering Wheel Angle
Sensor Type
65103 Vehicle Dynamic Stability 11 1813 VDC Information Signal Trucks
Control 1 with
1814 VDC Fully Operational
stability
1815 VDC brake light request control
1816 ROP Engine Control

active
1817 YC Engine Control
active
1818 ROP Brake Control
active
1819 YC Brake Control active
65217 High Resolution Vehicle 23 917 High Resolution Total All
Distance Vehicle Distance
918 High Resolution Trip
Distance
65271 Vehicle Electrical Power 0 158 Keyswitch Battery Since
1 Potential 2007
65260 Vehicle Identification 0 237 Vehicle Identification Since
Number 2010
65135 Adaptive Cruise Control 42 1586 Speed of forward vehicle By option
1587 Distance to forward
vehicle
1588 Adaptive Cruise Control
Set Speed
1589 Adaptive cruise control
set distance mode
1590 Adaptive Cruise Control
Mode
1796 ACC Distance Alert
Signal
1797 ACC System Shutoff
Warning
All Rights Reserved
SAE J1939 Messages
Source
Address
1798 ACC Target Detected
5022 Forward Collision
Warning
65264 Power Takeoff 17 980 Engine PTO Governor Mack
Information Enable Switch
984 Engine PTO Governor
Set Switch
256 Transmission Control 1 11 681 Transmission Gear Shift By ABS
Inhibit Request type with
Automatic
Transmis-
sion
1024 External Brake Request 3 2920 External Acceleration mDrive
Demand
2914 XBR EBI Mode
2915 XBR Priority
2916 XBR Control Mode
3189 XBR Message Counter
3188 XBR Message
Checksum
Notes
All Rights Reserved
Multiplexing Body Builder J1939 CAN
The multiplexing system BB J-1939 CAN is used to provide control and communication between all major functional areas
on a vehicle (engine, electrical, transmission, etc). The system offers simplified communication between the body builder
module and other related electrical systems. Multiple signals are sent over a single pair of twisted wires, as opposed to indi-
vidual wires for each function. The J1939 data link is used to send these signals.
The benefit of this arrangement is fewer wires, sensors and connections are required for communication purposes between
systems. Also, there is greater signal consistency and reliability.
Multiplexing Parameters
CAN Source of Receiver of
SAE Update Rate PGN Signal Names (SPN)
Network Message Message
ACC1 J1939-X VECU (as Ext CAN 100ms Forward vehicle speed
(65135) ACB) Forward vehicle distance
ACC Set Speed
ACC Mode
ACC set distance mode
Road curvature
ACC Target Detected
ACC System Shutoff Warning
ACC Distance Alert Signal
ACC J1939-X VECU (as Ext CAN 100ms (Proprietary message from ACB)
Status ACB) Audible Following Distance Alert
(65296) Visual Following Distance Alert
Vehicle Following Distance
Vehicle Following Interval
ACB Tell Tale Indicator Status
ACB J1939-X VECU (as Ext CAN 100ms CMT Intervention
Critical ACB) Impact Alert
Events
(PGN
65297
AIR1 J1939-X VECU Ext CAN 1 sec Pneumatic Supply Pressure 46
AMB J1939-X VECU (as Ext CAN 1 sec Ambient Air Temperature,
(65269) EMS) Barometric pressure
AT1S J1939-X VECU (per Ext CAN On Request Diesel Particulate Filter 1 Soot Load Percent
(PGN reply) 3719
64891) Diesel Particulate Filter 1 Ash Load
Percent 3720
AT1T1I J1939-X VECU (as Ext CAN 1s Aftertreatment 1 SCR Catalyst Tank Level
ACM) 1761
Aftertreatment 1 SCR Catalyst Tank Tempera-
ture 3031
Aftertreatment 1 SCR Catalyst Tank Level 2
3517
Aftertreatment 1 DEF Tank Low Level Indica-
tor 5245
Aftertreatment SCR Operator Inducement Se-
verity 5246
B J1939-X VECU (as Ext CAN 1s Brake Application Pressure (SPN 116) Brake
IC) Primary Pressure (SPN 117) Brake
All Rights Reserved
Secondary Pressure (SPN 118) Parking
Brake Red Warning Signal
(SPN 3557)
CCVS J1939-X VECU Ext CAN 100 ms Vehicle speed, etc.
(65265)
CI (PGN J1939-X VECU (as Ext CAN On Request Component ID, etc.
65259) EMS)
CVW J1939-X VECU (per Ext CAN On Request Weights
(PGN reply)
65136)
DD J1939-X VECU (as Ext CAN 1s Washer Fluid Level (SPN 80)
(65276) IC) Fuel Level 1 (SPN 96)
DM1 J1939-X VECU (as Ext CAN 1 sec Fault lamps, etc.
received)
DPFC1 J1939-X VECU (as Ext CAN 1s DPF status, etc.
(PGN EMS)
64892)
EBC1 J1939-X VECU (as Ext CAN 100ms Anti-Lock Braking (ABS) Active, etc.
(PGN ABS)
61441)
EBC1 J1939-X Ext CAN VECU 100ms Remote Accelerator Pedal Enable Switch, Ac-
(PGN celerator Interlock Switch
61441)
EBC1 J1939-X VECU Cummins 100ms Remote Accelerator Pedal Enable Switch
(PGN (SPN 969),
61441) Accelerator Interlock Switch (SPN 972)
Engine retarder selection (SPN 973)
EBC2 J1939-X VECU (as Ext CAN 100ms Wheel speeds
(WSI PGN ABS)
65215
EBC5 J1939-X VECU (as Ext CAN 100ms Hill Holder Mode
(PGN ABS)
64964)
EEC1 J1939-X VECU (as Ext CAN As received Engine Speed, etc
(61444) EMS)
EEC2 J1939-X VECU Ext CAN 50ms Accelerator Pedal Position
(61443)
EEC2 J1939-X Ext CAN VECU 50ms Remote Accelerator Pedal Position
(61443)
EEC2 J1939 VECU Cummins 50ms Accelerator Pedal Position 1 Remote Acceler-
(61443) ator Pedal Position
EFL/P1 J1939-X VECU (as Ext CAN 500ms Engine Oil Level 98
(PGN EMS) Engine Oil Pressure 100
65263) Engine Crankcase Pressure 101
Engine Coolant Level 111
All Rights Reserved
ET1 (PGN J1939-X VECU (as Ext CAN 1s Engine Coolant Temperature 110 Engine Fuel
65262) EMS) Temperature 1 174
Engine Oil Temperature 1 175
ETC1 J1939-X VECU (as Ext CAN 10 ms Driveline engaged status
TECU)
ETC2 J1939-X VECU (as Ext CAN 100ms Current gear status, requested gear status
TECU)
ETC7 J1939-X VECU (as Ext CAN 100 ms Shift and mode indicators, etc.
TECU)
GFC (PGN J1939-1 VECU (as Ext CAN on request Trip Fuel (Gaseous)
65199) EMS) 1039 Total Fuel Used (Gaseous) 1040
HOURS J1939-X VECU (as Ext CAN on request Engine Total Hours of Operation 247 Engine
(PGN EMS) Total Revolutions 249
65253)
HRLFC J1939-X VECU (as Ext CAN 1s High Resolution Engine Trip Fuel 5053 High
(PGN EMS) Resolution Engine Total Fuel Used 5054
64777)
HRW J1939-X VECU (as Ext CAN 20ms Wheel speeds
(PGN ABS)
65134)
IO (PGN J1939-X VECU (as Ext CAN On request Engine Total Idle Fuel Used 236
65244) EMS) Engine Total Idle Hours 235
IC1 (PGN J1939-X VECU (as Ext CAN 500ms Engine Exhaust Gas Temperature, etc.
65270) EMS)
LC (PGN J1939-X VECU (as Ext CAN 1 s and Light switches, etc.
65089) LCM) change of
state
state
LFC (PGN J1939-X VECU (as Ext CAN On request Engine Trip Fuel 182
65257) EMS) Engine Total Fuel Used 250
LFE (PGN J1939-X VECU (as Ext CAN 100ms Engine Fuel Rate 183
26266) EMS) Engine Instantaneous Fuel Economy 184
Engine Average Fuel Economy 185
OEL (PGN J1939-X VECU (as Ext CAN 1 s and Main Light Switch 2872
64972) IC) change of Turn Signal Switch 2876
state Hazard Light Switch 2875
High-Low Beam Switch 2874
Operators Desired Back-light 2878
PTO (PGN J1939-X VECU Ext CAN 100 ms Power Takeoff Set Speed 187
65264) Engine PTO Governor Enable Switch 980
Engine Remote PTO Governor Preprog-
rammed Speed Control Switch 979
Engine Remote PTO Governor Variable
Speed Control Switch 978
All Rights Reserved
Engine PTO Governor Set Switch 984 Engine
PTO Governor Coast/Decelerate Switch 983
Engine PTO Governor Resume Switch 982
PTODE J1939-X VECU (as Ext CAN 100 ms Engagement Consent – Transmission input
(PGN TECU) shaft PTO 2 (SPN 3457)
64932) Engagement Consent – Transmission input
shaft PTO 1 (SPN 3456)
ENGAGEMENT CONSENT – TRANSMIS-
SION OUTPUT SHAFT PTO (SPN 3458)
PTODE J1939-1 VECU TECU, Allison 100 ms Enable Switch – Transmission input shaft
(PGN PTO 2 (SPN 3453)
64932) Enable Switch – Transmission input shaft
PTO 1 (SPN 3452)
PTODE J1939-1 EXT CAN VECU 100 ms Enable Switch – Transmission input shaft
(PGN PTO 2 (SPN 3453)
64932) Enable Switch – Transmission input shaft
PTO 1 (SPN 3452)
Enable Switch - PTO Engine Accessory Drive
1
Request J1939-X Ext CAN VECU PGN
Request J1939–1 VECU As received As received PGN
in most cases
SERV J1939-X VECU Ext CAN On request Service component identification
(PGN Service distance (associated to upper Service
65216) component ID)
Service component identification
Service delay / calendar time based (associ-
ated to upper Service component ID)
Service component identification
Service delay / operational time based (asso-
ciated to upper Service component ID)
SOFT J1939-1 VECU Ext CAN On request Variable length
(PGN
65242)
TCFG J1939-1 VECU Ext CAN On request Number of Reverse Gear Ratios 958 Number
(PGN of Forward Gear Ratios 957 Transmission
65250) Gear Ratio 581
TC1 (PGN J1939-1 VECU TECU (Allison) 50ms (when See Allison Datalink Communication Guide
256) active)
TC1 (PGN J1939-X VECU (as Ext CAN 50ms (when See Allison Datalink Communication Guide
256) Shifter 05 active)
and 06)
TC1 (PGN J1939-1 Allison VECU 50ms (when See Allison Datalink Communication Guide
256) Shifter active)
TC1 (PGN J1939-X EXT CAN VECU 50ms (when See Allison Datalink Communication Guide
256) (DA TECU) active)
TD (PGN J1939-X VECU (as Ext CAN On Request Time & date
65254) IC)
All Rights Reserved
TSC1 J1939-1 VECU EMS 10ms Engine override control mode
(PGN 0) Override control mode priority
Engine requested torque/torque limit
Engine Requested Speed/Speed Limit 898
TSC1 J1939-1 Ext CAN (DA VECU 10ms Engine override control mode
(PGN 0) EMS) Override control mode priority
Engine requested torque/torque limit
TRF1 J1939-X VECU (as Ext CAN 1s Transmission Oil Temperature 177, etc.
(PGN TECU)
65272)
TRF2 J1939-X VECU (as Ext CAN 1s Transmission Overheat Indicator SPN 5345
(PGN TECU)
64917)
RF (PGN J1939-X VECU (as Ext CAN 1s Hydraulic Retarder Oil Temperature, Driveline
65275) TECU) Retarder Overheat Indicator
VD (PGN J1939-X VECU (as Ext CAN 1s Total Vehicle Distance 245
65248) IC) Convert from VDHR
VDC1 J1939-X VECU (as Ext CAN 100ms VDC Information Signal, etc.
(PGN ABS)
65103)
VDHR J1939-X VECU (as Ext CAN 1s High Resolution Total Vehicle Distance 917
(PGN IC)
65217)
VH (PGN J1939-X VECU Ext CAN On request Total Vehicle Hours 246
65255) Total Power Takeoff Hours 248
VI (PGN J1939-X VECU (as Ext CAN On request VIN

65260) EMS)
VW (PGN J1939-X VECU (as Ext CAN 1 sec Weights
65258) ECS) (note this is multiframe so is difficult to re-
spond to so will gateway at received rate)
VDC1 J1939-X VECU (as Ext CAN 100ms VDC Information Signal, etc.
(PGN ACB)
65103)
VP190 J1939-X VECU (as Ext CAN 15s SCR used
(PGN EMS)
65470)
VP60 J1939-1 VECU TECU (I shift) 100ms Reverse Inhibit, Inhibit gear engaged
(from TC1), PTO Conditions #1, PTO Condi-
tions #2
VEP1 J1939-X VECU (as Ext CAN 1s SPN 168 Battery Potential / Power Input 1
(PGN IC)
65271)
All Rights Reserved
Note: Although the VECU sends output messages, the source address is set as the ECU originating the information.
Note: Messages that rate “on request” are requested by the J1939 request PGN 59904 described in J1939-21. For example,
requesting engine hours is done by sending EAFF or EA00 with data E5 FE 00 (hex values).
Note: Not all messages are supported on all vehicles. For example, GFC is currently not available, even for natural gas en-
gines. However, GFC support could be available for these engines in the future.
Commands Accepted on the Body Connector J1939

Message Update Rate Content
EBC1 (PGN 61441) 100 milliseconds Remote Accelerator Pedal Enable
Switch
Accelerator Interlock Switch
EEC2 (61443) 50 milliseconds Accelerator Pedal Position 2
Remote Accelerator Pedal Position
PTODE (PGN 64932) 100 milliseconds Enable Switch – Transmission input
Enable Switch – Transmission input
Enable Switch - PTO Engine Accessory
Drive 1
TSC1 (PGN 0) (DA EMS) 10 milliseconds Engine Override Control Mode 695
Engine Requested Torque/Torque Limit
518
Engine Requested Speed/Speed Limit
898
TC1 (PGN 256) (DA TECU) 50 milliseconds (when active) See Allison Datalink Communication
Guide
Application Notes
By default, these commands are not accepted. To enable commands:
• QIW = 1 Bridge on J-1939 for Body Builder Enable (1) Level 4 Dealer Programmable
• QKH = 1 External CAN Control Enable (1) Level 4 Dealer Programmable
• QKX = 229 (Body Builder must use this Source address 229)
• A Terminating resistor for the network needs to be installed.

For safety, the accelerator and speed command signals will be overridden by a brake pedal application by default. If neces-
sary this options can be turned off with parameter QKD. Perform a safety analysis of the application before disabling.
Although the VECU accepts these messages, the destination address (DA) needs to be 0x00 for TSC1 and 0x03 for TC1.
The engine speed command can be sent either through the accelerator command or by direct engine speed command.
All Rights Reserved
Accelerator Pedal Commands
Remote Accelerator is commanded by sending EBC1. Remote Accelerator Enable Switch while also sending a position
in EEC2. Remote Accelerator Pedal Position.
Primary Pedal position can be disabled by sending EBC1. Remote Accelerator Enable Switch without EEC2. Remote Ac-
celerator Pedal Position or setting EEC2. Remote Accelerator Pedal Position to 0. But for clearer intent it is recom-
mended to send EBC1. Accelerator Interlock Switch.
Engine Speed Commands

An engine speed command is sent by setting TSC1. Engine Override Control Mode to 01-Speed Control and sending the
desired speed in SPN 898.
SPN 898 can also represent a speed limit if TSC1. Engine Override Control Mode is set to 03. Note that there are engine
performance effects while operated at a limit, therefore it is recommended to disable the accelerator pedal, if that serves the
intent, rather than set a limit at a command value.
Engine Torque can be limited using TSC1. Engine Override Control Mode 02 with corresponding value in SPN 518.
If commands and limits are desired at the same time, TSC1 can be repeated with different information to enable speed re-
quests and limits at the same time since the commands will persist. Although the commands will time out if not repeated, it is
recommended to end command sessions with TSC1. Engine Override Control Mode 00 which will end all limits and
commands.
PTO
mDrive and Allison Transmissions can accept PTODE to request PTO engagement through the “enable switch” signals.
PTODE is also a response from the transmission to these requests though the “engagement consent” signals.
Source Addresses and Unit Acronyms

Control Unit ECU Source address (SA) or Destination
Address (DA) in Hex
Engine Management System EMS 0x00
Transmission Electronic Control Unit/ TECU/TCM 0x03
Control Module
Antilock Brake System ABS 0x0B
Gear Shift Electronic Control Unit GSECU 0x05 (0x06 for right side on LR)
Engine Brake EB 0x0F
Vehicle Electronic Control Unit VECU 0x11
Instrument Cluster IC 0x17
Adaptive Cruise with Braking function ACB 0x2A
Electronically Controlled Suspension ECS 0x2F
Aftertreatment Control Module ACM 0x3D
All Rights Reserved
BodyLink III Body Builder Connector
POST DESCRIPTION
1. Battery Power (30A) 16. NEUTRAL SIGNAL
2 .Ignition Power (30A) 17. BODYLAMP GROUND INPUT
3. Stop Lamp 18. PTO #1
4. Tail Lamp 19. PTO # 2
5. Reverse Signal 20. SPEED CONTROL ON/OFF
6. LH Turn 21. BB 1939 (+)
7. RH Turn 22. BB 1939 (-)
8. AUX SW #1 (IGN-20A) 23. SPEED CONTROL SET/DECEL

9. AUX SW #2 (BATT-15A) 24. SPEED CONTROL RESUME/ACC
10. AUX SW #3 (IGN-15A) 25.
11. AUX SW #4 (IGN-15A) 26.
12.AUX SW #5 (IGN-10A) 27. LH TURN/STOP
13. AUX SW #6 (DOWN-15A) 28.
14. AUX SW #6 (UP-15A) 29. RH TURN/STOP
15. PARK BRAKE SIGNAL
Note: Cab Decal from the BodyLink III Body Builder Connector
Notes
All Rights Reserved
Support Inbound and Outbound J-1939 Message Information
Note: MACK does not recommend broadcasting on the data bus. However, it is known that there are devices on the market
which effect an engine speed control. MACK broadcasts the following with message and signal definition per SAE J1939-71.
Instrument Cluster
Message Bus From ECU To ECU Update Rate Content

B (65274) J1939–1 IC VECU 1s Brake Application Pressure (SPN 116)
Brake Primary Pressure (SPN 117)
Brake Secondary Pressure (SPN 118)
Parking Brake Red Warning Signal (SPN 3557)
CL (53248) J1939-1 IC VECU 5s and state Illumination Brightness Percent (SPN 1487)
change
CM1 (57344) J1939-1 IC VECU 1s Seat Belt Switch (SPN 1856)
Diesel Particulate Filter
Regeneration Inhibit Switch (SPN 3695)
Diesel Particulate Filter Regeneration Force
Switch (SNP 3696)
DD (65276) J1939-1 IC VECU 1s Washer Fluid Level (SPN 80)
Fuel Level 1 (SPN 96)
LC (PGN J1939-1 IC VECU 1 s and Low Beam Head Light Command 2349
65089) change of High Beam Head Light Command 2347
state Right Turn Signal Lights Command 2369
Left Turn Signal Lights 2367
Rotating Beacon Light Command (Hazard)
2385
OEL (PGN J1939-1 IC VECU 1 s and Main Light Switch 2872
64972) change of Turn Signal Switch 2876
TD (PGN J1939-1 IC VECU 1s Time & date
65254)
VEP1 (PGN J1939-1 IC VECU 1s SPN 168 Battery Potential / Power Input 1
65271)
VDHR (PGN J1939-1 IC VECU 1s High Resolution Total
65217) Vehicle Distance 917
All Rights Reserved
ACC/ABS

ACC1 (PGN J1939-1 ACB (0x2A) VECU 100ms Forward Vehicle Speed
65135) Forward Vehicle Distance
ACC Set Speed
ACC Mode
ACC Set Distance Mode
Road Curvature
ACC Target Detected
ACC System Shutoff Warning
ACC Distance Alert Signal
ACC Status J1939-1 ACB VECU 100ms (Proprietary message from ACB)
(PGN 65296) Audible Following Distance Alert
Visual Following Distance Alert
Vehicle Following Distance
Vehicle Following Interval
ACB Tell Tale Indicator Status
ACB Critical J1939-1 ACB VECU 100ms CMT Intervention Impact Alert
Events (PGN
65297)
EBC5 (PGN J1939-1 ABS VECU 100ms Hill Holder Mode
64964)
EBC1 (PGN J1939-1 ABS VECU 100ms Anti-Lock Braking (ABS) Active, etc.
61441)
EBC2 (WSI J1939-1 ABS VECU 100ms Wheel speeds
PGN 65215
HRW (PGN J1939-1 ABS VECU 20ms Wheel speeds
65134)
VDC1 (PGN J1939-1 ABS VECU 100ms VDC Information Signal, etc.
65103)
EMS/ACM

AT1T1I J1939-1 EMS VECU 1s Aftertreatment 1 DEF Tank Low Level Indicator
5245
verity 5246
AT1T1I J1939-1 ACM VECU 1s Aftertreatment 1 SCR Catalyst Tank Level
1761
ture 3031
3517
AT1S (PGN J1939-1 EMS VECU On Request Diesel Particulate Filter 1 Soot Load Percent
64891) (1s) 3719
Diesel Particulate Filter 1 Ash Load Percent
3720
CI (PGN J1939-1 EMS VECU 10 s Component ID, etc.
65259)
All Rights Reserved
DPFC1 J1939-1 EMS VECU 1s DPF status, etc
(PGN 64892)
EEC1 J1939-1 EMS VECU 20ms Engine Speed, etc
(61444) Variable?
ET1 (PGN J1939-1 EMS VECU 1s Engine Coolant Temperature 110

65262) Engine Fuel Temperature 1 174
EFL/P1 J1939-1 EMS VECU 500 ms Engine Oil Level 98
(PGN 65263) Engine Oil Pressure 100
Engine Crankcase Pressure 101
ERC1 (PGN J1939-1 EMS (as VECU 100 ms Retarder Torque Mode 900
61440) retarder) Actual Retarder - Percent Torque 520 Etc.
IC1 (PGN J1939-1 EMS VECU 500 ms Engine Intake Manifold #1 Pressure 102
65270) Engine Intake Manifold 1 Temperature 105
Engine Air Intake Pressure 106 Engine
Exhaust Gas Temperature 173
IO (PGN J1939-1 EMS VECU On Request Engine Total Idle Fuel Used 236
65244) (1s) Engine Total Idle Hours 235
GFC (PGN J1939-1 EMS VECU Currently Not Trip Fuel (Gaseous) 1039
65199) Supported Total Fuel Used (Gaseous) 1040
HRLFC J1939-1 EMS VECU 1s High Resolution Engine Trip Fuel 5053
(PGN 64777) High Resolution Engine Total Fuel Used 5054
HOURS J1939-1 EMS VECU 15s (on Engine Total Hours of Operation 247
(PGN 65253) request) Engine Total Revolutions 249
LFE (PGN J1939-1 EMS VECU 100ms Engine Fuel Rate 183
26266) Engine Instantaneous Fuel Economy 184
LFC (PGN J1939-1 EMS VECU On request Engine Trip Fuel 182
65257) (1 s) Engine Total Fuel Used 250
VI (PGN J1939-1 EMS VECU On request VIN

65260) (3 s)
VECU

AIR1 J1939-X VECU Ext CAN 1s Pneumatic Supply Pressure 46
AMB J1939-X VECU (as Ext CAN 1s Ambient Air Temperature
(65269) EMS) Barometric pressure
AT1S (PGN J1939-X VECU (per Ext CAN On Request Diesel Particulate Filter 1 Soot Load Percent
64891) reply) 3719
Diesel Particulate Filter 1 Ash Load Percent
3720
AT1T1I J1939-X VECU (as Ext CAN 1s Aftertreatment 1 SCR Catalyst Tank Level
ACM) 1761
ture 3031
All Rights Reserved
3517
Aftertreatment 1 DEF Tank Low Level Indicator
5245
verity 5246
B J1939-X VECU (as Ext CAN 1s Brake Application Pressure (SPN 116)
IC) Brake Primary Pressure (SPN 117)
Brake Secondary Pressure (SPN 118)
Parking Brake Red Warning Signal (SPN
3557)
CCVS J1939-X VECU Ext CAN 100 ms Vehicle Speed, etc.
(65265)
CI (PGN J1939-X VECU (as Ext CAN On Request Component ID, etc.
65259) EMS)
CVW (PGN J1939-X VECU (per Ext CAN 1s Weights
65136) reply)
DD (65276) J1939-X VECU (as Ext CAN 1s Washer Fluid Level (SPN 80)
IC) Fuel Level 1 (SPN 96)
DM1 J1939-X VECU (as Ext CAN 1s Fault lamps, etc.
received)
DPFC1 J1939-X VECU (as Ext CAN 1s DPF status, etc.
(PGN EMS)
64892)
EBC1 (PGN J1939-X VECU (as Ext CAN 100 ms Anti-Lock Braking (ABS) Active, etc.
61441) ABS)
EBC1 (PGN J1939-X Ext CAN VECU 100 ms Remote Accelerator Pedal Enable Switch
61441) Accelerator Interlock Switch
EBC1 (PGN J1939-X VECU Cummins 100 ms Remote Accelerator Pedal Enable Switch
61441) (SPN 969)
Accelerator Interlock Switch (SPN 972)
Engine retarder selection (SPN 973)
EBC2 (WSI J1939-X VECU (as Ext CAN 100 ms Wheel Speeds
PGN 65215) ABS)
EBC5 (PGN J1939-X VECU (as Ext CAN 100 ms Hill Holder Mode
64964) ABS)
EEC1 J1939-X VECU (as Ext CAN As received Engine Speed,etc
(61444) EMS)
EEC2 J1939-X VECU Ext CAN 50 ms Accelerator Pedal Position
(61443)
EEC2 J1939-X Ext CAN VECU 50 ms Remote Accelerator Pedal Position
(61443)
EEC2 J1939 VECU Cummins 50 ms Accelerator Pedal Position 1
(61443) Remote Accelerator Pedal Position
EFL/P1 J1939-X VECU (as Ext CAN 500 ms Engine Oil Level 98
(PGN 65263 EMS) Engine Oil Pressure 100
All Rights Reserved
Engine Crankcase Pressure 101
ET1 (PGN J1939-X VECU (as Ext CAN 1s Engine Coolant Temperature 110
65262) EMS) Engine Fuel Temperature 1 174
ETC1 J1939-X VECU (as Ext CAN 10 ms Driveline engaged status
TECU)
ETC2 J1939-X VECU (as Ext CAN 100 ms Current Gear Status
TECU) Requested gear status
ETC7 J1939-X VECU (as Ext CAN 100 ms Shift and mode indicators, etc.
TECU)
GFC (PGN J1939-1 VECU (as Ext CAN On Request Trip Fuel (Gaseous) 1039
65199) EMS) Total Fuel Used (Gaseous) 1040
HOURS J1939-X VECU (as Ext CAN On Request Engine Total Hours of Operation 247
(PGN EMS) Engine Total Revolutions 249
65253)
HRLFC J1939-X VECU (as Ext CAN 1s High Resolution Engine Trip Fuel 5053
(PGN EMS) High Resolution Engine Total Fuel Used 5054
64777)
HRW (PGN J1939-X VECU (as Ext CAN 20 ms Wheel speeds
65134) ABS)
IO (PGN J1939-X VECU (as Ext CAN On Request Engine Total Idle Fuel Used 236
65244) EMS) Engine Total Idle Hours 235
IC1 (PGN J1939-X VECU (as Ext CAN 500 ms Engine Exhaust Gas Temperature, etc
65270) EMS)
state
LFE (PGN J1939-X VECU (as Ext CAN 100 ms Engine Fuel Rate 183
26266) EMS) Engine Instantaneous Fuel Economy 184
OEL (PGN J1939-X VECU (as Ext CAN 1 s and Main Light Switch 2872
64972) IC) change of Turn Signal Switch 2876
PTO (PGN J1939-X VECU Ext CAN 100 ms Power Takeoff Set Speed 187
65264) Engine PTO Governor Enable Switch 980
Engine Remote PTO Governor Preprog-
rammed Speed Control
Switch 979
Engine Remote PTO Governor Variable Speed
Control Switch 978
Engine PTO Governor Set Switch 984
Engine PTO Governor Coast/Decelerate
Switch 983
Engine PTO Governor Resume Switch 982
All Rights Reserved
PTODE J1939-X VECU (as Ext CAN 100 ms Engagement Consent – Transmission input
(PGN TECU) shaft PTO 2 (SPN 3457)
64932) Engagement Consent – Transmission input
PTODE J1939-1 VECU TECU, 100 ms Enable Switch – Transmission input shaft PTO
(PGN Allison 2 (SPN 3453)
64932) Enable Switch – Transmission input shaft PTO
1 (SPN 3452)
PTODE J1939-1 Ext CAN VECU 100 ms Enable Switch – Transmission input shaft PTO
(PGN 2 (SPN 3453)
64932) Enable Switch – Transmission input shaft PTO
1 (SPN 3452)
Enable Switch - PTO Engine Accessory Drive
1
Request J1939-X Ext CAN VECU PGN
Request J1939-1 VECU As received As received PGN
in most
cases
SERV (PGN J1939-X VECU Ext CAN On Request Service Component Identification
65216) Service Distance (associated to upper Service
component ID)
Service Component Identification
Service delay / calendar time based (associ-
ated to upper Service component ID)
Service Component Identification
Service Delay / Operational Time Based (asso-
ciated to upper Service component ID)
SOFT (PGN J1939-1 VECU Ext CAN On Request Variable length
65242)
TCFG (PGN J1939-1 VECU Ext CAN On Request Number of Reverse Gear Ratios 958
65250) Number of Forward Gear Ratios 957
Transmission Gear Ratio 581
TC1 (PGN J1939-1 VECU TECU 50ms (when See Allison Datalink Communication Guide
256) (Allison) active)
TC1 (PGN J1939-X VECU (as Ext CAN 50ms (when See Allison Datalink Communication Guide
256) Shifter 05 active)
and 06)
TC1 (PGN J1939-1 Allison VECU 50ms (when See Allison Datalink Communication Guide
256) Shifter active)
TC1 (PGN J1939-X EXT CAN VECU 50ms (when See Allison Datalink Communication Guide
256) (DA TECU) active)
TD (PGN J1939-X VECU (as Ext CAN On Request Time & date
65254) IC)
TSC1 (PGN J1939-1 VECU EMS 10 ms Engine Override Control Mode
0) Override Control mode Priority
All Rights Reserved
TSC1 (PGN J1939-1 Ext CAN (DA VECU 10 ms Engine Override Control Mode
0) EMS) Override Control Mode Priority
TRF1 (PGN J1939-X VECU (as Ext CAN 1s Transmission Oil Temperature 177, etc.
65272) TECU)
TRF2 (PGN J1939-X VECU (as Ext CAN 1s Transmission Overheat Indicator SPN 5345
64917) TECU)
RF (PGN J1939-X VECU (as Ext CAN 1s Hydraulic Retarder Oil Temperature
65275) TECU) Driveline Retarder Overheat Indicator
VD (PGN J1939-X VECU (as Ext CAN 1s Total Vehicle Distance 245
65248) IC) Convert from VDHR
VDC1 (PGN J1939-X VECU (as Ext CAN 100 ms VDC Information Signal, etc.
65103) ABS)
VDHR (PGN J1939-X VECU (as Ext CAN 1s High Resolution Total Vehicle Distance 917
65217) IC)
VH (PGN J1939-X VECU Ext CAN On Request Total Vehicle Hours 246
65255) Total Power Takeoff Hours 248
VI (PGN J1939-X VECU (as Ext CAN On Request VIN

65260) EMS)
VW (PGN J1939-X VECU (as Ext CAN 1s Weights (note this is multiframe so is difficult to
65258) ECS) respond to so will gateway at received rate)
VDC1 (PGN J1939-X VECU (as Ext CAN 100 ms VDC Information Signal, etc.
65103) ACB)
VP190 (PGN J1939-X VECU (as Ext CAN 15 s SCR used
65470) EMS)
VP60 J1939-1 VECU TECU (Ishift) 100 ms Reverse Inhibit
Inhibit Gear Engaged (from TC1)
PTO Conditions #1
PTO Conditions #2
VEP1 (PGN J1939-X VECU (as Ext CAN 1s SPN 168 Battery Potential / Power Input 1
65271) IC)
Transmission

ETC1 J1939-1 Automated VECU 10 ms Driveline engaged status
Trans
ETC2 J1939-1 Automated VECU 100 ms Current gear status, requested gear status
Trans
ETC7 J1939-1 Allison VECU 100 ms Range Display, Mode indicator
PTODE J1939-1 TECU (Ishift) VECU 100 ms Engagement Consent – Transmission input
(PGN 64932) shaft PTO 2 (SPN 3457)
Engagement Consent – Transmission input
All Rights Reserved
PTODE J1939-1 TECU VECU 100 ms Engagement Consent – Transmission input
(PGN 64932) (Allison) shaft PTO 2 (SPN 3457)
Engagement Consent – Transmission input
PTODE J1939-1 VECU, EXT TECU 100 ms Enable Switch – Transmission input shaft PTO
(PGN 64932) CAN (SA 33, (Allison) 2 (SPN 3453)
SA 23) Enable Switch – Transmission input shaft PTO
1 (SPN 3452)
Engagement Consent – Transmission output
shaft PTO (SPN 3458)
SOFT (PGN J1939-1 Allison VECU On Request Variable Length
65242)
TranTC1 J1939-1 EXT CAN, TECU 50ms (when See Allison Datalink Communication Guide
(256) Allison (Allison) active)
Shifter
TCFG (PGN J1939-1 Allison VECU On Request Number of Reverse Gear Ratios 958
65250) Number of Forward Gear Ratios 957
Transmission Gear Ratio 581
TRF1 (PGN J1939-1 Automated VECU 1s Transmission Oil Temperature 177, etc.
65272) Trans
TRF2 (PGN J1939-1 Allison VECU 1s Transmission Overheat Indicator SPN 5345
64917)
RF (PGN J1939-1 Allison VECU 1s Hydraulic Retarder Oil Temperature
65275) Driveline Retarder Overheat Indicator
VP60 J1939-1 VECU Ishift 100 ms Inhibit Gear Engaged
Reverse Inhibit
PTO Conditions #1
PTO Conditions #2
ECS

VW (PGN J1939-X ECS VECU 1 sec (SAE Weight by axle (1 frame for each axle)
65258) says On
Request)
All Rights Reserved
Parameters Description and Location
Caption Description Location Resolution Min Max Default Parameter ID

Value Value
Ext CAN (CAN2) Diagnostics VECU 1 0 1 0 Level 4 QKE
Enabling this parameter results in
faults if the Body CAN is not properly
connected or if the device does not ac-
knowledge messages.
Ext CAN (CAN2) Fault Level VECU 1 0 1 0 Level 4 QKF
This parameter adjusts the behavior of
the fault enabled by QKE.
Ext CAN Control enable VECU 1 0 1 0 Level 4 QKH
This parameter will allow the truck to
accept body commands whereby QKX
and optionally QKW must represent
the source address of the device.
Ext CAN gateway enable VECU 1 0 1 0 (set to 1 Level 4 QIW
This parameter enables transmission per
of information to external devices. Use project)
QKE to enable diagnostics for this port.
If on-request parameters are needed
then the SA of the requesting device
must be set by QKX and vehicle sour-
ces can be changed for some specific
messages by QKG, QKV, QKU, and QIV.
If vehicle response to commands is al-
so expected then set QKH
Transmission Type VECU 1 0 7 0 Level 2 BZN
SA for device (Note F1 & F9 SA for TSC1, VECU 1 0 255 229 Level 4 QKX
PTODE, VP45, EEC2, EBC1)
If a device on the Ext CAN will request
messages or send commands to the
truck then this needs to reflect the
source address of the added device.
Also set QKH Take note of QKD
SA for device (Note F1SA for TC1) VECU 1 0 255 6 Level 4 QKW
If a device on the Ext CAN is to broad-
cast TC1 commands then this needs to
be set to what the transmission will ac-
cept and the device needs to send with
this source address. However this can
not be the same as any on-vehicle
shifter broadcasting per QIV. Also set
parameter QKH.
SA for GFC (Note : F4 SA of message VECU 1 0 255 0 Level 4 QKG
used to respond to device request)
This parameter should reflect the
source address of the vehicle device
responding to a request for message
GFC.
All Rights Reserved
Caption Description Location Resolution Min Max Default Parameter ID
Value Value
SA for CVW VECU 1 0 255 3 Level 4 QKV
SA for TCFG (Note : F4 SA) VECU 1 0 255 3 Level 4 QKU
This parameter should reflect the
source address of the vehicle device
responding to a request for message
TCFG.
SA for TC1 (Note : F2 SA) This parame- VECU 1 0 255 5 Level 4 QIV
ter should reflect the source address of
the vehicle device supplying message
TC1
Ext CAN Break Pedal Override VECU 1 0 255 1 Level 4 QKD
If this parameter is set then Ext CAN
accelerator pedal position and engine
speed commands will be set to idle
while the service brake is pressed.
Notes
All Rights Reserved
CAN Bus Road Speed Signal Kit
Note: The kit shown below is required to obtain road speed signal through J–1939 CAN Bus with GEN 2 Interior Trucks. It is re-
quired for Conventional trucks with M-Drive and Mack Manual Transmissions. To order this kit, you must contact Body Builder
Support at 1-877-770-7575 and have VIN# ready. This kit will only be sent for trucks that are being up fitted with bodies that re-
quire road speed signal.
J–1939 CAN Bus Reader Installation for Road Speed
W3140107
Fig. 37 Sailes CB1J1939-HF kit
Note: This kit is not required if your truck has an Allison transmission. Allison provides a road speed signal at the Allison Body
Builder connector located left of the steering column behind the kick panel. Wire # N125 Pin F of the connector. (See Connector
Below)
W3140108
Fig. 38 Allison Body Builder Connector
All Rights Reserved
W3140109
Fig. 39 Terminating resistor
A - Find the terminating resistor under the pie plate at Fuse Relay panel and remove the terminating resistor.
W3140110
Fig. 40 Connecting the CAN Bus reader
B – Insert terminating resistor in the female connector on the CAN Bus reader cable.
C – Plug in the CAN Bus cable male connector in the female connector on the truck cab harness term resistor connector.
All Rights Reserved
W3140111
Fig. 41 IGN OPT connector
D – Connect the female Y power harness connector to the male IGN OPT connector
W3140112
Fig. 42 Connecting the CAN Bus reader
E – Connect the male connector of the power harness to the female power connector on the CAN Bus reader (fused side).
Note: The other leg of the power harness is for another ignition option.
All Rights Reserved
W3140113
Fig. 43 CAN Bus reader installed
Secure with tie straps. Installation is complete. This is what it should look like when completed.
Note: The orange wire is the road speed output for your device.
Note: The CAN Bus reader produces a 12 volt speed pulse of 8000 ppm.
All Rights Reserved

Mack Section 3 New

Uploaded by

Copyright:

Available Formats

Mack Section 3 New

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Mack Section 3 New

Uploaded by

Copyright:

Available Formats

What are some of the main sections covered in the document?

What are some of the main sections covered in the document?

How can a body builder obtain the road speed signal?

How can a body builder obtain the road speed signal?

BODY BUILDER INSTRUCTIONS

Electrical Wiring and Connections

• “General Wiring Definitions”, page 5

• “Routing and Clipping Guidelines”, page 6

• “Body Builder Connectors, Schematic Examples”, page 18

• “Remote Start n Stop”, page 24

• “Remote Engine Stop”, page 25

• “Adding Auxiliary Accelerator Pedal”, page 26

• “BodyLink III”, page 27

• “Auxiliary Switch Locations (Cab)”, page 31

• “Power Connections”, page 32

• “Control Link II”, page 38

• “RP170A Refuse Related Chassis to Body Interface Connectors”, page 51

• “Wiring J1939”, page 57

• “9-pin Diagnostic Connector”, page 59

• “16-pin Diagnostic Connector”, page 60

• “Termination Resistor”, page 65

• “Parameter List”, page 66

• “Multiplexing Body Builder J1939 CAN ”, page 82

• “Support Inbound and Outbound J-1939 Message Information ”, page 90

• “CAN Bus Road Speed Signal Kit”, page 100

PI / CHU, AN / CXU, GR / GU, TD, LR, TE / MRU

Current status of the truck in relation to ISO 26262

• BOC Back of Cab

• CAN Controller Area Network

• CDS Custom Defined Statement (replaced by DCL)

• DCL DataMax Control Language

• ECM Engine Control Module

• EHT Electronic Hand Throttle

• EMS Engine Management System

• ESC Engine Speed Control

• FMI Failure Mode Identification

• GMT Greenwich Mean Time

• MID Message Identifier (J1587 source)

• PGN Parameter Group Number (J1939 message ID)

• PID Parameter Identification (J1587)

• PID Product Identification (order code)

• PTO Power Take Off

• PTT2 Premium Tech Tool 2

• SA Source Address (J1939 unit identifier)

• SID Subsystem Identification (J1587)

• SPN Suspect Parameter Number (J1939 parameter)

• SSC Single Speed Control

• TCM Transmission Control Module

• VDA Vehicle Data Administration (OEM database)

• VECU Vehicle Electronic Control Unit

• V-MAC Vehicle Management And Control (Mack brand electronics name)

AWG American Wire Gauge

Bundled With A number of items tied, wrapped, or otherwise held together

Contacts Items touching each other.

Material Grade 30 Minimum yield strength of 30,000 psi

Material Grade 50 Minimum yield strength of 50,000 psi

Routing and Clipping Guidelines

1 Support electrical cables every 18 inches (450 mm)