TL072

TL072A - TL072B
LOW NOISE J-FET DUAL OPERATIONAL AMPLIFIERS

■ WIDE COMMON-MODE (UP TO VCC+) AND

DIFFERENTIAL VOLTAGE RANGE
■ LOW INPUT BIAS AND OFFSET CURRENT
■ LOW NOISE en = 15nV/√Hz (typ)
■ OUTPUT SHORT-CIRCUIT PROTECTION
N
■ HIGH INPUT IMPEDANCE J–FET INPUT DIP8
STAGE (Plastic Package)
■ LOW HARMONIC DISTORTION : 0.01% (typ)
■ INTERNAL FREQUENCY COMPENSATION
■ LATCH UP FREE OPERATION
■ HIGH SLEW RATE : 16V/µs (typ)
D
SO8
(Plastic Micropackage)

DESCRIPTION ORDER CODE

Package
The TL072, TL072A and TL072B are high speed Part Number Temperature Range
J–FET input dual operational amplifiers incorpo- N D
rating well matched, high voltage J–FET and bipo- TL072M/AM/BM -55°C, +125°C • •
lar transistors in a monolithic integrated circuit. TL072I/AI/BI -40°C, +105°C • •
TL072C/AC/BC 0°C, +70°C • •
The devices feature high slew rates, low input bias
Example : TL072CN
and offset current, and low offset voltage temper-
N = Dual in Line Package (DIP)
ature coefficient. D = Small Outline Package (SO) - also available in Tape & Reel (DT)

PIN CONNECTIONS (top view)

1 - Offset null 1
1 8 2 - Inverting input 1
3 - Non-inverting input 1
2 7 4 - VCC-
-
5 - Non-inverting input 2
6 -Inverting input 2
3 + - 6 7 - Output 2
8 - VCC+
4 + 5

March 2001 1/10

TL072 - TL072A - TL072B

SCHEMATIC DIAGRAM

VCC

Non-inverting
input
Inverting
input
1 0 0Ω
2 0 0Ω
Output

1 0 0Ω
30k 1/2 TL072

8.2k

1.3k 35k 1.3k 35k 1 0 0Ω

VCC

ABSOLUTE MAXIMUM RATINGS

Symbol Parameter TL072M, AM, BM TL072I, AI, BI TL072C, AC, BC Unit
VCC Supply voltage - note 1) ±18 V
Vi Input Voltage - note 2) ±15 V
Vid 3) ±30 V
Differential Input Voltage - note
Ptot Power Dissipation 680 mW
Output Short-circuit Duration - note 4) Infinite
Toper Operating Free-air Temperature Range -55 to +125 -40 to +105 0 to +70 °C
Tstg Storage Temperature Range -65 to +150 °C
1. All voltage values, except differential voltage, are with respect to the zero reference level (ground) of the supply voltages where the zero reference
level is the midpoint between VCC + and VCC -.
2. The magnitude of the input voltage must never exceed the magnitude of the supply voltage or 15 volts, whichever is less.
3. Differential voltages are the non-inverting input terminal with respect to the inverting input terminal.
4. The output may be shorted to ground or to either supply. Temperature and/or supply voltages must be limited to ensure that the dissipation rating
is not exceeded

2/10
 TL072 - TL072A - TL072B

ELECTRICAL CHARACTERISTICS
VCC = ±15V, Tamb = +25°C (unless otherwise specified)
TL072I,M,AC,AI,AM,
TL072C
Symbol Parameter BC,BI,BM Unit
Min. Typ. Max. Min. Typ. Max.
Input Offset Voltage (Rs = 50Ω) mV
Tamb = +25°C TL072 3 10 3 10
TL072A 3 6
Vio TL072B 1 3
Tmin ≤ Tamb ≤ Tmax TL072 13 13
TL072A 7
TL072B 5
DVio Input Offset Voltage Drift 10 10 µV/°C
Input Offset Current - note 1)
Iio Tamb = +25°C 5 100 5 100 pA
Tmin ≤ Tamb ≤ Tmax 4 10 nA
Input Bias Current -note 1
Iib Tamb = +25°C 20 200 20 200 pA
Tmin ≤ Tamb ≤ Tmax 20 20 nA
Large Signal Voltage Gain (RL = 2kΩ, Vo = ±10V) V/mV
Avd Tamb = +25°C 50 200 25 200
Tmin ≤ Tamb ≤ Tmax 25 15
Supply Voltage Rejection Ratio (RS = 50Ω) dB
SVR Tamb = +25°C 80 86 70 86
Tmin ≤ Tamb ≤ Tmax 80 70
Supply Current, no load mA
ICC Tamb = +25°C 1.4 2.5 1.4 2.5
Tmin ≤ Tamb ≤ Tmax 2.5 2.5

Vicm ±11 +15 ±11 +15 V

Input Common Mode Voltage Range
-12 -12
Common Mode Rejection Ratio (RS = 50Ω) dB
CMR Tamb = +25°C 80 86 70 86
Tmin ≤ Tamb ≤ Tmax 80 70
Output Short-circuit Current mA
Ios Tamb = +25°C 10 40 60 10 40 60
Tmin ≤ Tamb ≤ Tmax 10 60 10 60
Output Voltage Swing V
Tamb = +25°C RL = 2kΩ 10 12 10 12
±Vopp RL = 10kΩ 12 13.5 12 13.5
Tmin ≤ Tamb ≤ Tmax RL = 2kΩ 10 10
RL = 10kΩ 12 12
Slew Rate (Tamb = +25°C) V/µs
SR
Vin = 10V, RL = 2kΩ, CL = 100pF, unity gain 8 16 8 16

tr
Rise Time (Tamb = +25°C) µs
Vin = 20mV, RL = 2kΩ, CL = 100pF, unity gain 0.1 0.1
Overshoot (Tamb = +25°C) %
Kov
Vin = 20mV, RL = 2kΩ, CL = 100pF, unity gain 10 10
Gain Bandwidth Product (Tamb = +25°C) MHz
GBP
Vin = 10mV, RL = 2kΩ, CL = 100pF, f= 100kHz 2.5 4 2.5 4
Ri Input Resistance 1012 1012 Ω

3/10
TL072 - TL072A - TL072B

TL072I,M,AC,AI,AM,
TL072C
Symbol Parameter BC,BI,BM Unit
Min. Typ. Max. Min. Typ. Max.
Total Harmonic Distortion (Tamb = +25°C)
%
THD f= 1kHz, RL = 2kΩ,CL = 100pF, Av = 20dB,
0.01 0.01
Vo = 2Vpp
Equivalent Input Noise Voltage nV
en ------------
RS = 100Ω, f = 1KHz 15 15 Hz
∅m Phase Margin 45 45 degrees
Channel separation dB
Vo1/Vo2
Av = 100 120 120
1. The input bias currents are junction leakage currents which approximately double for every 10°C increase in the junction temperature.

4/10
 TL072 - TL072A - TL072B

MAXIMUM PEAK-TO-PEAK OUTPUT MAXIMUM PEAK-TO-PEAK OUTPUT

VOLTAGE versus FREQUENCY VOLTAGE versus FREQUENCY

MAXIMUM PEAK-TO-PEAK OUTPUT MAXIMUM PEAK-TO-PEAK OUTPUT

VOLTAGE versus FREQUENCY VOLTAGE versus FREE AIR TEMP.

MAXIMUM PEAK-TO-PEAK OUTPUT MAXIMUM PEAK-TO-PEAK OUTPUT

VOLTAGE versus LOAD RESISTANCE VOLTAGE versus SUPPLY VOLTAGE

30
MAXIMUM PEAK-TO-PEAK OUTPUT

RL = 10 kΩ
25
Tamb = +25˚C

20
VOLTAGE (V)

15

10

0 2 4 6 8 10 12 14 16
SUPPLY VOLTAGE ( V)

5/10
TL072 - TL072A - TL072B

INPUT BIAS CURRENT versus FREE AIR LARGE SIGNAL DIFFERENTIAL VOLTAGE
TEMPERATURE AMPLIFICATION versus FREE AIR TEMP.

100 1000
V CC = 15V
400
INPUT BIAS CURRENT (nA)

10 200

DIFFERENTIAL VOLTAGE
AMPLIFICATION (V/V)
100

1 40
20
10 V CC = 15V
0.1 V O = 10V
4
2 R L = 2k Ω

0.01 1
-50 -25 0 25 50 75 100 125 -75 -50 -25 0 25 50 75 100 125

TEMPERATURE (˚C) TEMPERATURE (˚C)

LARGE SIGNAL DIFFERENTIAL VOLTAGE TOTAL POWER DISSIPATION versus FREE AIR
AMPLIFICATION AND PHASE SHIFT versus TEMPERATURE
FREQUENCY

250
DIFFERENTIAL VOLTAGE

100 225 V CC = 15V

TOTAL POWER DISSIPATION (mW)

180
AMPLIFICATION (V/V)

DIFFERENTIAL
VOLTAGE
200 No signal
PHASE SHIFT AMPLIFICATION No load
(right scale) 175
(left scale)
150
10 90 125
R = 2kW 100
L
C L = 100pF 75
1 V CC = 15V 0 50
T amb = +125°C 25
0
100 1K 10K 100K 1M 10M
-75 -50 -25 0 25 50 75 100 125
FREQUENCY (Hz)
TEMPERATURE (˚C)

SUPPLY CURRENT PER AMPLIFIER versus COMMON MODE REJECTION RATIO versus
FREE AIR TEMPERATURE FREE AIR TEMPERATURE

2.0 89
1.8 V CC = 15V R L = 10 kΩ
COMMON MODE MODE REJECTION

1.6 No signal 88
VC C = 15V
SUPPLY CURRENT (mA)

1.4 No load
87
1.2
RATIO (dB)

1.0 86
0.8
0.6 85
0.4 84
0.2
0 83
-75 -50 -25 0 25 50 75 100 125
-75 -50 -25 0 25 50 75 100 125
TEMPERATURE (˚C) TEMPERATURE (˚C)

6/10
 TL072 - TL072A - TL072B

VOLTAGE FOLLOWER LARGE SIGNAL PULSE OUTPUT VOLTAGE versus ELAPSED TIME
RESPONSE

28
INPUT AND OUTPUT VOLTAGES

6
24
4 OUTPUT OVERSHOOT

OUTPUT VOLTAGE (mV)

INPUT 20 90%

2 16
0
(V)

12
VCC= 15V
8
-2 R L = 2 kW V = 15V
CC
C L= 100pF 4 R L = 2k Ω
-4 10%
Tamb = +25°C 0 Tamb = +25˚C
-6 tr
0 0.5 1 1.5 2 2.5 3 3.5 -4
0 0.1 0.2 0.3 0.4 0.5 0.6 0.7
TIME (m s) TIME ( µs)

EQUIVALENT INPUT NOISE VOLTAGE versus TOTAL HARMONIC DISTORTION versus

FREQUENCY FREQUENCY

70 1
VCC = 15V V VCC = = 15V 15V
TOTAL HARMONIC DISTORTION

60 CC
A V = 10 0.4
A AV V= =1 1
EQUIVALENT INPUT NOISE

50 R S = 100 Ω V VO O(rms) = =6V6V

VOLTAGE (nV/VHz)

0.1 (rms)
T amb = +25˚C T amb= =+25˚C
T amb +25˚C
40 0.04
(%)

30
0.01
20
0.004
10
0 0.001
10 40 100 400 1k 4k 10k 40k 100k 100 400 1k 4k 10k 40k 100k
FREQUENCY (Hz) FREQUENCY (Hz)

7/10
TL072 - TL072A - TL072B

PARAMETER MEASUREMENT INFORMATION

Figure 1 : Voltage Follower Figure 2 : Gain-of-10 Inverting Amplifier

10k Ω
1k Ω
eI -
1/2
TL072 eo

RL CL = 100pF

TYPICAL APPLICATIONS
100KHz QUADRUPLE OSCILLATOR

18k Ω *
1N 4148 -15V

18pF 1k Ω
18pF

-
1/2 88.4k Ω
TL072 -
1/2
88.4k Ω 6 cos ω t
TL072
6 sin ω t
1k Ω
18pF

88.4k Ω
1N 4148
18k Ω *

+15V

* These resistors values may be adjusted for a symmetrical output

8/10
 TL072 - TL072A - TL072B

PACKAGE MECHANICAL DATA

8 PINS - PLASTIC DIP

Millimeters Inches
Dim.
Min. Typ. Max. Min. Typ. Max.
A 3.32 0.131
a1 0.51 0.020
B 1.15 1.65 0.045 0.065
b 0.356 0.55 0.014 0.022
b1 0.204 0.304 0.008 0.012
D 10.92 0.430
E 7.95 9.75 0.313 0.384
e 2.54 0.100
e3 7.62 0.300
e4 7.62 0.300
F 6.6 0260
i 5.08 0.200
L 3.18 3.81 0.125 0.150
Z 1.52 0.060

9/10
 TL072 - TL072A - TL072B

PACKAGE MECHANICAL DATA

8 PINS - PLASTIC MICROPACKAGE (SO)

Millimeters Inches
Dim.
Min. Typ. Max. Min. Typ. Max.
A 1.75 0.069
a1 0.1 0.25 0.004 0.010
a2 1.65 0.065
a3 0.65 0.85 0.026 0.033
b 0.35 0.48 0.014 0.019
b1 0.19 0.25 0.007 0.010
C 0.25 0.5 0.010 0.020
c1 45° (typ.)
D 4.8 5.0 0.189 0.197
E 5.8 6.2 0.228 0.244
e 1.27 0.050
e3 3.81 0.150
F 3.8 4.0 0.150 0.157
L 0.4 1.27 0.016 0.050
M 0.6 0.024
S 8° (max.)

Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences
of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted
by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject
to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not
authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics.
© The ST logo is a registered trademark of STMicroelectronics

© 2001 STMicroelectronics - Printed in Italy - All Rights Reserved

STMicroelectronics GROUP OF COMPANIES
Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco
Singapore - Spain - Sweden - Switzerland - United Kingdom
© http://www.st.com

10/10