Setseal 22

Setseal 22
Water based paraffin dispersion concrete curing compound (Formerly known as

Setcrete 22)
Description Method of Use
Setseal 22 is a water based curing compound formulated Setseal 22 should be spray applied as soon as possible to
from selected emulsified paraffin to form a low viscosity the fresh concrete, provided that the surface water has
wax emulsion. evaporated.
Setseal 22 is supplied as clear and white pigmented Do not apply if bleed water is forming, or is present on
colours, the clear colour is a white liquid, which forms the concrete surface. S r Setseal 22 well before use to
a wet white film when applied to concrete surfaces, ensure even pigment dispersion.
this dries to form a transparent film. The white pigment
colour is a white milky liquid, which forms a white film Setseal 22 should be spray applied, the spray nozzle
a er drying and reflect 60 – 80% of the sunlight providing should be held approximately 450 mm from the concrete
the recommended coverage has been maintained. surface and passed back and forth to ensure complete
coverage. Pump pressure should be maintained to give
The two grades are designed to retain sufficient moisture an even, fine spray.
in the concrete to ensure full hydra on of the cement,
which is essen al for op mum strength development. The applied film should be protected from rain for at least
3 hours; care should be taken to ensure that the film is
Applications not broken.
Setseal 22 is used mainly for newly cast concrete and In case of formed concrete, Setseal 22 should be applied
cemen ous surfaces to retain sufficient moisture to immediately a er de-shu ering. In such a case the
ensure full hydra on of the cement. Typical applica on concrete surface must be dampened with clean water
areas include: prior applica on of Setseal 22. Dry surfaces may prevent
correct film forma on and cause absorp on of the
 Runways and roads. Setseal 22 into the concrete surface, which may lead to
 Roof decks. staining and difficulty in later degrada on and removal.
 Retaining walls.
 Irriga on canals. Remarks
 Concrete floors.
 Columns and underground founda ons.  It is important that the complete removal of the
Setseal 22 is ensured prior to the applica on of any
Advantages surface finishes or addi onal surface treatments.
 Setseal 22 can be removed by using high pressure
 Helps achieving concrete desired strengths. steam, water je ng or light sand blas ng.
 Minimizes poten al surface cracking and shrinkage.  It is recommended to use Setseal A/AW where the
 Promotes a harder dust free surface. concrete is to receive a coa ng or further surface
 Single component. treatment.
 Can be spray applied to reduce labor cost.  Setseal 22 minimum applica on temperature is 5°C.
 Solvent based curing compounds are also available
Standards from DCP.
 Setseal 22 complies with AASHTO M148 and ASTM Cleaning

C309, Type 1 and 2, Class A when used at the
recommended coverage rate. Tools and equipment can be cleaned with soaped water
 Water reten on (kg / m2) < or = 0.55. when wet. Dried Setseal 22 should be removed with DCP
 Setseal 22 is suitable for use in structures that will be in Solvent.
contact with potable water when tested in accordance
with BS 6920.
Setseal 22
Packaging More from Don Construction Products
Setseal 22 is available in 25 litre pails and 200 litre drums. A wide range of construc on chemical products are
manufactured by DCP which include:
Coverage
 Concrete admixtures.
The recommended coverage rate is 2.5 - 3.5 m²/litre.  Surface treatments
 Grouts and anchors.
Storage  Concrete repair.
 Flooring systems.
Store in a dry area out of direct sunlight between 5°C and  Protec ve coa ngs.
35°C.  Sealants.
 Waterproofing.
Shelf Life  Adhesives.
 Tile adhesives and grouts.
Setseal 22 has a shelf life of 12 months from date of  Building products.
manufacture for the clear version, and 9 months for the  Structural strengthening.
pigmented, if stored in proper condi ons in un-opened
drums.
If these condi ons are exceeded, DCP Technical

Department should be contacted for advise.
Cautions
Health and Safety
Setseal 22 is not classified as hazardous material.

In case of accidental splashes to the eyes, rinse with clean
water and seek medical advise. Suitable protec ve gloves
and goggles should be worn.
For further informa on refer to the Material Safety Data

Sheet.
Fire
Setseal 22 is water based and is nonflammable.
DCP Solvent is flammable. Ensure adequate ven la on.

Do not use near a naked flame and do not smoke during
use.
Flash Point:
DCP Solvent: 37°C.
02-0002-B-2019

Setseal 22 - TDS PDF

Uploaded by

Copyright:

Available Formats

Setseal 22 - TDS PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Setseal 22 - TDS PDF

Uploaded by

Copyright:

Available Formats

Water based paraﬃn dispersion concrete curing compound (Formerly known as

Description Method of Use

 Setseal 22 complies with AASHTO M148 and ASTM Cleaning

If these condi ons are exceeded, DCP Technical

Health and Safety

Setseal 22 is not classiﬁed as hazardous material.

For further informa on refer to the Material Safety Data

Setseal 22 is water based and is nonﬂammable.

DCP Solvent is ﬂammable. Ensure adequate ven la on.

You might also like