MD6250

Rotary Blasthole Drill

Specifications
11.2 or 13.6 m (36.7 or 44.6 ft)
Mast Configurations

Description Basic Specs (continued)

The MD6250 crawler-mounted blasthole drill is designed to drill U.S. EPA Tier 2 equivalent
from 152-250 mm (6-9.8 in) diameter holes in Rotary or DTH Engine C27 ACERT™ @ 1,800 rpm
(Down the Hole) modes to single pass or multi pass depths.
Emissions U.S. EPA Tier 2 equivalent
Basic Specs Power Rating (ISO 14396) 616 kW 826 hp
U.S. EPA Tier 4 Final
11.2 m (36.7 ft) mast Engine C27 ACERT @ 1,800 rpm
Hole diameter range Up to 152­ Up to 6-9.8 in Emissions U.S. EPA Tier 4 Final
250 mm
Power Rating (ISO 14396) 643 kW 872 hp
Hole depth range
Compressor, Rotary drilling 56.6 m3/min (2,000 ft3/min)
Single-pass depth 11.2 m 36.7 ft @ 8.6 bar (125 psi)
Multi-pass depth Down to 53.9 m Down to 176.7 ft Compressors, DTH drilling 38.2 m3/min (1,350 ft3/min)
Pull-down capacity Up to 20 411 kg Up to 45,000 lb @ 34.4 bar (500 psi)
Hoist capacity Up to 20 411 kg Up to 45,000 lb 42.4 m3/min (1,500 ft3/min)
Hoist speed 0.81 m/sec 2.65 ft/sec @ 24.1 bar (350 psi)
Bit load (single-pass) Up to 22 321 kg Up to 49,210 lb Angle drilling Vertical to 30° (in 5° increments)
13.6 m (44.6 ft mast)
Hole diameter range Up to 152­ Up to 6-9.8 in
250 mm
Hole depth range
Single-pass depth 13.6 m 44.6 ft
Multi-pass depth Down to 37.9 m Down to 124.6 ft
Pull-down capacity Up to 29 483 kg Up to 65,000 lb
Hoist capacity Up to 22 113 kg Up to 48,750 lb
Hoist speed 0.66 m/sec 2.16 ft/sec
Bit load (single-pass) Up to 32 655 kg Up to 71,993 lb
MD6250 Specifications

Engine Choices Cooling

• Dual starter motors • Coolers with easy cleaning access
• Scheduled oil sampling (S·O·SSM) ports • Separate engine cooling module
• Common air intake filters provide +500 hour service interval • All cooler core sections are replaceable
in normal operating conditions • Functional in ambient temperature of 52° C (125° F)
• Ether starting aid (ether bottle supplied locally) • Automatic variable speed fan control

Compressor Choices Climate Choices

DTH drilling Includes tool lubrication system Climate Level 1 Standard f luids and lubricants
and hammer storage • Rated down to –1° C (30° F)
1350 cfm/500 psi 38.2 m3/min (1,350 ft3/min) • Withstands high heat to 52° C (125° F)
@ 34.4 bar (500 psi) includes Climate Level 2 Arctic f luids and lubricants
113.5 L (30 gal) tool oiler • Rated down to –18° C (– 0.4° F)
1500 cfm/350 psi 42.4 m3/min (1,500 ft3/min) Climate Level 4 Arctic f luids and lubricants
@ 24.1 bar (350 psi) includes • Rated down to – 40° C (–40° F)
113.5 L (30 gal) tool oiler • Diesel fired heating system that heats and circulates engine
Rotary drilling Optional tool lubrication system coolant through: engine block, below deck water tank, heating
2000 cfm/125 psi 56.6 m3/min (2,000 ft3/min) @ elements for battery trays, with a provision for fuel tanks.
8.6 bar (125 psi) • Full Arctic lubricant package to include: engine oil, compressor
oil and hydraulic oil.
With the compressor’s variable volume control, the operator can
• Electric heating package with breaker panel to power: 120V
limit air output resulting in reduced fuel consumption. Both high
heating blanket for compressor receiver tank, compressor
and low pressure compressors contain this feature.
control box, heat trace for compressor control lines, heat trace
Electronic compressor control and regulation with purged air lines for hosing from water tank to water pump and water fast-fill
assembly, plus tank.
Receiver Tank Choices • Shore power connection box with switchable 240-600V (50 amp)
connection (diesel gen set and/or plug supplied locally). Box
• Low pressure 8.6 bar (125 psi) for ASME/CRN/AU or CE includes standard 50 hz battery charger, if 60 hz charger
• High pressure 24.1 or 34.4 bar (350 or 500 psi) for required to be ordered via after market, refer to P-n 540-4271
ASME/CRN/AU or CE • Breaker panel includes five (5) additional breakers for locally
supplied heating elements if needed.

 MD6250 Specifications

Frame and Work Deck Hydraulics

• Jacks, mast pivot and deck are welded integrally to mainframe • Two (2) primary pumps – 145 cc (piston, with proportional
for maximum durability and long life electronic controls)
• Stationary drill deck for vertical and angle drilling • One (1) auxiliary circuit pump – 110 cc (piston, load sensing)
• Four leveling jacks provide leveling on a 7° bench (any orientation) • Two (2) fan pumps – 74 cc (piston, with proportional
• Slip resistant surfaces electronic controls)
• Fuel tank capacity 1416 L (374 gal) • Two (2) charge pumps – 43.9 + 56.5 cc (double stack gear,
• Fuel capacity expansion for additional 1416 L (374 gal) fixed displacement)
• Three (3) egress points on deck areas in addition to main access • Scheduled Oil Sampling (S·O·S) ports
• Heavy duty tow hooks (front end)
• Four (4) lift lugs, for use with cables or chains Mast and Pipe Carousel Features
• Pipe guide roller assembly mounted on drill deck for loading
drill pipe • Pipe carousel, standard:
• Walk-around cab access (with railing and toe guards) for cab – 11.2 m (36.7 ft) Mast: holds quantity of four (4) 10.6 m

perimeter to drill deck (option) (35 ft) pipes

• Cab-roof access ladder with guard plus roof safety railing for – 13.6 m (44.6 ft) Mast: holds quantity of four (4) 6.1 m

ease of access to air conditioner/pressurizer/heater (option) (20 ft) pipes

• Platform to mount fire suppression bottles and/or diesel gen set • Pipe carousel, dual purpose:
on non-drill-end (option) – 11.2 m (36.7 ft) Mast: holds quantity of two (2) 10.6 m (35 ft)
pipes and quantity of two (2) 7.62 m (25 ft) pipes, and adapters
Frame Access Choices to connect to DTH hammer and tricone bit (DTH hammer and
tricone not included)
• Fixed access stairs to the cab area – Accepts 140 mm (5.5 in) or 168 mm (6.625 in) pipe – contact

• Cascading hydraulic stairs with walkway around the cab to the factory for additional pipe diameters

drill deck (option). Includes jack and tram interlock activated • Vertical or angle drilling 0-30°; in 5° increments
when the stairs are down • Hydraulically actuated, self-indexing pipe carousel accepts pipe
diameters from 127 mm (5.0 in) to 194 mm (7.625 in)
Drill Deck Misc. • Drill strings configured for bit changes (above the deck)
• Single cylinder pulldown/hoist system
• Toolbox (option) • Auto tensioning of pull down and hoist cables
• Hydraulic viewing hatch on drill deck with spotlight (option) • Sliding deck wrench assembly
• Drill pipe thread greaser actuated from the cab (option) • Configured with roller deck bushing
• Jib crane ready (option) • Overhead winch with cable and hook plus remote control;
variable speed drive with ≥ 1818 kg (4,000 lb) rating, length
Undercarriage to reach 6.1 m (20 ft) past drill deck (option)
• Tool oiler, 113.5 L (30 gal) oil injection system (option for low
Model Cat® 336E EL Excavator type pressure compressor configurations)
Lower rollers Twelve (12) • Variable grip hydraulic break out wrench range choices are
114 mm to 152 mm (4.5 in to 6.0 in) or 152 mm to 216 mm
Carrier rollers Three (3)
(6.0 in to 8.5 in)
Track chain guards and guides Level two • Closed circuit camera in mast is used to view pipe carousel/top
Drawbar pull 417 000 N 93,745 lbf drive operation while racking pipes
Travel speed 2.45 kph 1.5 mph • Pipe positioner for angle drilling or multi-pass pipe handling,
actuated from the cab, with safety interlocks
Triple grousers 600 mm (23.6 in); for hard
• Rotation gear box with single motor, up to 160 rpm, up to
rock 0.88 bar (12.7 psi) ground
11 600 N∙m (8,555 lbf-ft) torque
pressure
Triple grousers 750 mm (29.5 in); for soft rock
1.10 bar (15.9 psi) ground
pressure

MD6250 Specifications

Mast Accessories Carousel (Mast size and pipe diameter dependent)

• 11.2 m (36.7 ft) or 13.6 m (44.6 ft) Manual pipe catcher – Standard carousel pipe:
One (1) wire rope pipe catcher, manual bit basket 10.6 m (35 f t) pipes for 11.2 m (36.7 f t) Mast – holds quantit y of four (4)
• 11.2 m (36.7 ft) Mast, One (1) hydraulically actuated pipe catcher, 127 mm 5.0 in
hydraulically operated bit basket
• 13.6 m (44.6 ft) Mast, One (1) hydraulically actuated pipe catcher, 140 m m 5.5 in
plus one (1) wire rope pipe catcher, hydraulically operated 152 mm 6.0 in
bit basket 165 mm 6.5 in
178 mm 7.0 in
Tool Package Rotary 194 mm 7.625 in
• One-piece roller deck bushing 6.1 m (20 f t) pipes for 13.6 m (4 4.6 f t) Mast – holds quantity of four (4)
• Pipe positioner rollers 127 mm 5.0 in
• Deck wrench 140 m m 5.5 in
• Top sub
152 mm 6.0 in
• Bit sub
• Pipe wiper seal 165 mm 6.5 in
• Drill tool lubricator (optional) 178 mm 7.0 in
• Shock sub (option) 194 mm 7.625 in
Dual purpose carousel pipe:
Tool Package DTH
11. 2 m (36.7 ft) Mast: holds quantity of two (2) 10.6 m (35 ft) pipes
• Two-piece roller deck bushings and quantit y of t wo (2) 7.62 m (25 f t) pipes, and adaptors to
• Pipe positioner rollers connect to DTH hammer and tricone bit (DTH hammer and tricone
• Deck wrench not included)
• Shock sub Dual purpose pipe carousel accepts 140 mm (5.5 in) or
• Top Sub 168 mm (6.625 in) pipe – contact factory for additional pipe
• Hammer Sub diameters
• Pipe wiper seal Overhead Winch System with remote (option)
• Drill tool lubricator is included with selection of DTH Compressor
Capacity rating 1814 kg 4,000 lb
Cable diameter 13 mm 0.5 in
Reach – past the drill deck 6.1 m 20 ft
• Variable speed drive

Rotary Head Top Drive System

Torque, single motor 11 700 N∙m 8,629 lbf-ft
Rotation speed 0-160 rpm
• Spindle – 140 mm (5.5 in) API regular thread with splined collar
• Rotary torque control
• Virtual rotary head travel interlocks

 MD6250 Specifications

Operator Environment Operating System Controls (Standard)

• Cab design: • All electric controls for drilling, tramming, leveling plus
– Spacious FOPS cab has 3 m 2 (32.3 ft2) floor space with an
auxiliary functions
integrated operator station
• Rotary torque control
– Cab rubber shock-mounts absorb mechanical vibration and
• Virtual rotary head travel stops
restrict exterior noise
• Pipe positioner engaged/disengaged indicator, with interlock
– Operator station design integrates an ergonomic seat, joystick • Drill depth meter
controls with full instrumentation, and dual 254 mm (10 in) color • Drill performance and display system
displays, high definition touchscreen and 12 volt power port • Delayed engine shut down
– Additional display screen for cc cameras; color, high-definition • Filter indicators for hydraulic, fuel, compressor and engine
254 mm (10 in) • Jack pressure sensors in display
– Power convertor 24V to 12V • Data logging of machine health with warnings and fault code
– Radio-ready for communication and entertainment stereo records with export capability
– Cab roof access system with ladder, cage and rails (optional) • Dust suppression control
– Two swing out doors and Cat keyed locks • Mast lock indicator
– Literature holder • ECM proportional fan speed control system
• Cab packages: • Tram interlock, machine stability limits
– Standard configuration includes a fabric seat, single pane
• Tram interlock, pipe in hole
window glass, and wiper for the driller window
• Tram interlock, mast up and locked or down and parked
– Premium configuration includes additional storage, a leather • Tram interlock, jack retracted
seat with heat and ventilation, heavy duty suspension, dual • Tram interlock, winch parked
pane window glass, a removable guard for front window, • Cab environment controls (AC, filter, heat, fan speeds)
wipers for the driller window plus front and rear windows • Pre wired for Terrain and Autonomous Operation
• Seating: • Drill Assist automated functionality:
– Seat swivels, locks and retractable, two-point/76 mm (3 in) wide – Auto level, auto jack retract
seat belt, tilts (5° adjustment), lumbar support, fore/aft seat – Auto mast raise and lock, auto mast unlock and park
adjustment 80 mm (3.1 in)
– Fold away trainer’s seat with seat belt (option) Premium Controls
• Windows:
– Large windows front, rear and right cab side; full length drill • Drill Assist automated functionality:
window with guard – Auto drill single pass (option)
– Windshield wipers with a common washer tank
– Window shades (option) Automation and Technology
– Manometer Pressure Gauge (option)
• Lighting: • Drill performance indicators: feed and rotary torque pressure,
– LED interior lights and map light at operators seat, backlit
head RPM, bit air pressure, target depth and drill depth, pipe
joysticks and keypads
counter, water injection flow rate, advance per revolution, rate
– Flood lights for the drill perimeter of penetration
– Spot lights for power group area; drill deck; mast carousel;
• Drill Assist (auto level, auto retract jacks, auto raise and lower
access ladder and walkways
mast, single-pass auto drill)
– Standard lighting is 1,300 lumens flood light on perimeter,
• Cat Terrain ready
area spot lights have 1,950 lumens
• Product Link Elite
– Premium lighting package includes 4,200 lumens flood light on • Autonomy ready
perimeter, mast clearance lights, cab mounted strobe, front
mounted tram beacon (option)
• HVAC:
– Floor heating vent
– Roof-mounted air conditioner/heating/pressurizing unit
– Filter access from deck, 500 service interval
– Defogging HVAC vents on main window
• Cameras:
– Three (3) CC cameras (front and left side) providing 360° vision
coverage from operators seat; camera on the mast to view pipe
carousel/top drive operation

MD6250 Specifications

Dust Control Choices Safety and Security

Water injection – tank mounted 1271 L 336 gal • Platform on non-drill-end for mounting fire suppression bottles
below front deck and/or diesel gen set (option)
Water f low meter, volume control, tank fill level indicator • Approach angle of 15 degrees facilitates loading and unloading
Water injection plus dry dust collector on a lowboy
• Alloy drill deck covers, for servicing when mast is horizontal
127 m3/min (4,500 ft3/min) dust collector; includes standard
• Seven (7) engine shut down buttons, by each drill egress/access
water injection
point, in cab, in engine area, on drill deck
Self-cleaning filters, dust chute with ejector • Over forty (40) conditional safety interlocks
High volume water injection 2786 L 736 gal • Hinged window guard over the full length of the front drill window
(maximum) – tanks total • Three (3) egress points on deck areas in addition to main access
capacity • Self-closing gates secure egress ladder locations
Tank below deck – capacity 1271 L 336 gal • Electric horn activated by push button in the cab
(isolated for extreme cold • Automatic tram alarm
weather) • Under deck mounted battery box with keyed battery
disconnect/starter disconnect/remote jump start terminals
Tank above deck – capacity 1514 L 400 gal
• Compressor air hoses with safety retention cables
• Static dust curtains, four sided/boxed enclosed • Slip resistant surfaces
• Dust curtain hydraulic lifters raise front and rear dust curtains • Tow hooks on non-drill-end
(option) (recommended with dust collector) • Lifting lugs
• Tram off spray to wet the ground around the cuttings pile (option) • Front window guard (option)

Service Packages
• Basic – Centralized manual lubrication for all pivot points,
gravity fill for fuel and water
• Standard – Fast fill for fuel and water, automated lubrication
system (option)
• Service center for lubricant drain and fill, automated lubrication
system, fast fill fuel and water, blow down hose (option)

 MD6250 Specifications

Dimensions
All dimensions are approximate.

2
1

4 2 5
1

11.2 m (36.7 ft) Mast 13.6 m (44.6 ft) Mast

1 Width cab end 5.625 m 18.45 ft 5.624 m 18.45 ft
2 Width non-cab end 4.845 m 15.9 ft 4.845 m 15.9 ft
3 Height mast up 17.146 m 56.3 ft 19.546 m 61.13 ft
4 Body length 11.708 m 38.41 ft 11.708 m 38.41 ft
5 Length mast down 17.78 m 58.3 ft 20.18 m 66.17 ft
6 Height mast down 5.134 m 16.84 ft 5.134 m 16.84 ft
7 Mast only shipping length 16.32 m 53.5 ft 18.72 m 61.4 ft

Note: Width and length dimensions include: cascading stairs and walk-around access for cab.

Weights
Working weight range 56 468 kg to 64 154 kg 124,490 lb to 141,436 lb

MD6250 Configuration Choices

Mandatory Choices
Mandatory choices may vary. Consult your Cat dealer for details.
ENGINE UNDERCARRIAGE PIPE CAROUSEL, STANDARD
• C27 ACERT, 1,800 rpm Tier 2 equivalent • 600 mm (23.6 inch) triple grousers – • 11.2 m (36.7 ft) Mast
• C27 ACERT, 1,800 rpm Tier 4 Final hard rock – holds quantity of four (4) 10.6 m

• 750 mm (29.5 inch) triple grouser – soft rock (35 ft) pipes

COMPRESSOR/RECEIVER TANK • 13.6 m (44.6 ft) Mast

• Rotary/Single Stage, Low Pressure: MAST – holds quantity of four (4) 6.1 m

– 56.6 m3/min (2,000 ft3/min) @ 8.6 bar • 11.2 m (36.7 ft) Mast (20 ft) pipes

(125 psi); with Low Pressure Receiver – Single-pass depth – 11.2 m (36.7 ft)
Tank for ASME/CRN/AU or CE Tank – Multi-pass depth – Up to 53.6 m (176.7 ft) PIPE CAROUSEL, DUAL PURPOSE
• DTH/Two Stage, High Pressure: – Vertical or angle drilling package • 11.2 m (36.7 ft) Mast: holds a quantity of
– 38.2 m3/min (1,350 ft3/min) @ 34.4 bar • 13.6 m (44.6 ft) Mast two (2) 10.6 m (35 ft) pipes and a quantity
(500 psi), with High Pressure Receiver – Single-pass depth – 13.6 m (44.6 ft) of two (2) 7.62 m (25 ft) pipes with adaptors
Tank (500 psi) for ASME/CRN/AU or to connect to DTH Hammer and Tricone
– Multi-pass depth – Up to 37.9 m (124.6 ft)
CE Tank; hammer storage and 113.5 L Bit (DTH Hammer and Tricone Bit not
– Vertical or angle drilling package included)
(30 gal) tool oiler
– 42.4 m3/min (1,500 ft3/min) @ 24.1 bar
MAST ACCESSORIES BREAK OUT WRENCH
(350 psi), with High Pressure Receiver
Tank (350 psi) for ASME/CRN/AU or • 11.2 (36.7 ft) or 13.6 (44.6 ft) Mast • Variable grip hydraulic break out wrench
CE Tank; hammer storage and 113.5 L – Manual pipe catcher – One (1) wire rope grip range:
(30 gal) tool oiler pipe catcher, manual bit basket – 114-152 mm (4.5-6.0 in)
• 11.2 m (36.7 ft) Mast – 152-216 mm (6.0-8.5 in)
FRAME ACCESS – Hydraulic – One (1) hydraulic pipe
• Fixed access ladder catcher, hydraulically operated bit basket
• Cascading, hydraulic stairs with walkway • 13.6 m (44.6 ft) Mast
around the cab to the deck (required for – Hydraulic – One (1) hydraulic pipe catcher,
cab roof access system) plus one (1) wire rope, hydraulically
operated bit basket

 MD6250 Configuration Choices

Mandatory Choices (continued)

Mandatory choices may vary. Consult your Cat dealer for details.
DRILL TOOL PACKAGES – 11.2 m (36.7 ft) MAST DRILL TOOL PACKAGES – 13.6 m (44.6 ft) MAST SUBS
• Rotary 127 mm (5 in) pipe diameter – • Rotary 127 mm (5.0 in) pipe diameter – • Shock absorber with crossover adapter
Roller deck bushing, pipe positioner roller, Roller deck bushing, pipe positioner roller, – 127 mm (5.0 in)
deck wrench, cross over subs, pipe wiper seal deck wrench, cross over sub, pipe wiper seal – 140 mm (5.5 in)
(select top sub arrangement in next section) (select top sub arrangement in next section) – 152 mm (6.0 in)
• Rotary 152 mm (6 in) pipe diameter – • Rotary 152 mm (6.0 in) pipe diameter – – 165 mm (6.5 in)
Roller deck bushing, pipe positioner roller, Roller deck bushing, pipe positioner roller,
– 178 mm (7.0 in)
deck wrench, cross over subs, pipe wiper seal deck wrench, cross over sub, pipe wiper seal
(select top sub arrangement in next section) (select top sub arrangement in next section) – 194 mm (7.625 in)
• Rotary 165 mm (6.5 in) pipe diameter – • Rotary 165 mm (6.5 in) pipe diameter – • Shock subs with long top sub adaptor for
Roller deck bushing, pipe positioner roller, Roller deck bushing, pipe positioner roller, Dual Purpose 11.2 m (36.7 ft) Mast
deck wrench, cross over subs, pipe wiper seal deck wrench, cross over sub, pipe wiper seal – 140 mm (5.5 in)
(select top sub arrangement in next section) (select top sub arrangement in next section) – 168 mm (6.625 in)
• Rotary 178 mm (7.0 in) pipe diameter – • Rotary 178 mm (7.0 in) pipe diameter – • Top subs (Rotary package only)
Roller deck bushing, pipe positioner roller, Roller deck bushing, pipe positioner roller, – 127 mm (5.0 in)
deck wrench, cross over subs, pipe wiper seal deck wrench, cross over sub, pipe wiper seal – 152 mm (6.0 in)
(select top sub arrangement in next section) (select top sub arrangement in next section) – 165 mm (6.5 in)
• Rotary 194 mm (7.625 in) pipe diameter – • Rotary 194 mm (7.625 in) pipe diameter – – 178 mm (7.0 in)
Roller deck bushing, pipe positioner roller, Roller deck bushing, pipe positioner roller,
– 194 mm (7.625 in)
deck wrench, cross over subs, pipe wiper seal deck wrench, cross sub, pipe wiper seal
(select top sub arrangement in next section) (select top sub arrangement in next section)
OPERATOR ENVIRONMENT
• DTH 140 mm (5.5 in) pipe diameter – • DTH 140 mm (5.5 in) pipe diameter –
• Lighting
Two (2) piece bushing, pipe positioner Two (2) piece bushing, pipe positioner
roller, deck wrench, cross over adapter roller, deck wrench, cross over adapter – Standard Light, 1,300 lumens flood
for hammer, pipe wiper seal (select top sub for hammer, pipe wiper seal (select top sub light on perimeter, area spot lights have
arrangement in next section) arrangement in next section) 1,950 lumens
• DTH 165 mm (6.5 in) pipe diameter – • DTH 165 mm (6.5 in) pipe diameter – – Premium Light, 4,200 lumens per flood
Two (2) piece bushing, pipe positioner Two (2) piece bushing, pipe positioner light on perimeter, area spot lights have
roller, deck wrench, cross over adapter roller, deck wrench, cross over adapter 1,950 lumens mast clearance lights and
for hammer, pipe wiper seal (select top sub for hammer, pipe wiper seal (select top sub cab mounted yellow strobe light and front
arrangement in next section) arrangement in next section) mounted tram beacon
• Dual purpose 140 mm (5.5 in) pipe • DTH 178 mm (7.0 in) pipe diameter – • Cab packages
diameter – Two (2) piece bushing, pipe Two (2) piece deck bushing, pipe positioner – Standard configuration includes a fabric
positioner roller, deck wrench and dual roller, deck wrench, cross over hammer seat, single pane window glass, and wiper
purpose carousel adapter, pipe wiper seal (select top sub for the driller window
• Dual purpose 168 mm (6.625 in) pipe arrangement in next section) – Premium configuration includes additional
diameter – Two (2) piece bushing, pipe storage, a leather seat with heat and
positioner roller, deck wrench and dual ventilation, heavy duty suspension, dual
purpose carousel pane window glass, a removable guard
for front window, wipers for the driller
window plus front and rear windows
• Decals/Films
– ANSI
– ISO

MD6250 Configuration Choices

Mandatory Choices (continued)

Mandatory choices may vary. Consult your Cat dealer for details.
SERVICE PACKAGES BATTERIES TECHNOLOGY AND AUTOMATION
• Basic – Centralized manual lubrication for • Four (4) Cat sealed batteries • Drilling parameters and interlocks
all pivot points, gravity fill fuel and water • Six (6) Cat sealed batteries – required for • Drill Assist (auto level, auto retract jacks,
• Standard – Fast fill for fuel and water, cold weather level 2 and 4 and/or autonomy auto raise and lower mast, single-pass
automated lubrication system packages auto drill)
• Premium – Service center for lubricants • Product Link Elite (see selection
fill, fast fill fuel and water, automated CLIMATE choices below)
lubrication system, and blowdown hose • Climate Level 1
– Rated down to –1° C (30° F)
DUST CONTROL – Withstands high heat to 52° C (125° F)
• Water injection system – Standard fluids and lubricants
– 1271 L (336 gal) mounted below front deck • Climate Level 2
• Water injection plus dry dust collector – Rated down to –18° C (–0° F)
– 127 m3/min (4,500 cfm) dust collector – Arctic fluids and lubricants
– Water storage 1271 L (336 gal) • Climate Level 4
• High volume water injection – Arctic f luids and lubricants
– Water storage 2786 L (736 gallon) – Diesel fired heating system
– 1271 L (336 gal) tank mounted below deck – Electric powered heating system
– 1514 L (400 gal) mounted above deck

10

 MD6250 Factory Options

Factory Options
Options may vary. Consult your Cat dealer for details.
FRAME TECHNOLOGY PRODUCTS DRILL PIPE*

• Fuel tank expansion of +1609 L (425 gal) • Product Link Elite; satellite, cellular or dual Standard carousel pipe:

for total of 3218 L (850 gal) (Required for • Terrain guidance system hardware • 10.6 m (35 ft) pipes for 11.2 m (36.7 ft) Mast –
autonomy packages) Accepts quantity of four (4)
• Platform on non-drill-end to mount fire DUST SUPPRESSION – 127 mm (5.0 in)
suppression bottles and/or diesel gen set • Dust curtains, four sides boxed in, with – 140 mm (5.5 in)
• Jib crane ready (Jib crane not included) hydraulic lifters to raise front and rear dust – 152 mm (6.0 in)
curtains (recommended with dust collector) – 165 mm (6.5 in)
MAST • Tram off spray system – 178 mm (7.0 in)
• Overhead winch assembly with cable and – 194 mm (7.625 in)
hook, plus with remote control; variable DRILL BITS, ROTARY TRICONE • 6.1 m (20 ft) pipes for 13.6 m (44.6 ft) Mast –
speed drive with ≥ 1814 kg (4,000 lb) rating, • Recommended for Rotary Applications Accepts quantity of four (4)
length to reach 6.1 m (20 ft) past drill deck • All bits have standard nozzles – 127 mm (5.0 in)
• Tool lubrication system for Rotary Drilling • Obtain S/M/H codes from the Rock
with 113.5 L (30 gal) capacity – 140 mm (5.5 in)
Formation to Bit Conversion table – 152 mm (6.0 in)
• Pipe thread greaser with reloadable tank https://catpublications.com search
for disposable grease bucket – 165 mm (6.5 in)
for PEXQ1027
– 178 mm (7.0 in)
• Ship out plans for each drill configuration
SERVICE TOOLS allow for one pallet of bits. Additional – 194 mm (7.625 in)
• Bushing retention tool – 102-194 mm pallets may require an additional truck. • 10.6 m (35 ft) pipe for 11.2 m (36.7 ft) Mast –
(4.0-7.625 in) – 171 mm (6.75 in), Option 1, (S2) Accepts quantity of two (2)
• Work Tools – 171 mm (6.75 in), Option 2, (M1) – Quantity of two (2) 7.62 m (25 ft) pipes
– Lifting bails (available on request;
with adaptors to connect to DTH hammer
– 171 mm (6.75 in), Option 3, (M3)
required for commissioning)
or tricone bit (hammer and tricone bit not
– 200 mm (7.875 in), Option 1, (S2) included)
• API thread 89 mm (3.5 in) – 200 mm (7.875 in), Option 2, (M1)
• API thread 114 mm (4.5 in) – 140 mm (5.5 in)
– 200 mm (7.875 in), Option 3, (M3) – 168 mm (6.625 in)
• API thread 140 mm (5.5 in) – 229 mm (9.0 in), Option 1, (S3)
• BECO thread 102 mm (4.0 in) – 229 mm (9.0 in), Option 2, (M2) *Contact factory for additional pipe
• BECO thread 114 mm (4.5 in) – 229 mm (9.0 in), Option 3, (H1) diameters
• BECO thread 152 mm (6.0 in) – 251 mm (9.875 in), Option 1, (M1)
– 251 mm (9.875 in), Option 2, (M3)
DRILL DECK MISC.
– 251 mm (9.875 in), Option 3, (H1)
• Tool box in deck
• Hydraulic viewing hatch with spotlight

OPERATOR ENVIRONMENT
• Fold up trainer’s seat with seat belt
• Cabin pressure manometer gauge
• Window shades
• Cab roof access system with ladder, cage
and rails (only available with cascading
stairs and cab walkway)

11

MD6250 Rotary Blasthole Drill

For more complete information on Cat products, dealer services, and industry solutions, visit us on the web AEHQ7996-07 (05-2019)

at www.cat.com Replaces AEHQ7996-06

© 2019 Caterpillar
All rights reserved

Materials and specifications are subject to change without notice. Featured machines in photos may include
additional equipment. See your Cat dealer for available options.

CAT, CATERPILLAR, LET’S DO THE WORK, their respective logos, “Caterpillar Yellow,” the “Power Edge”
and Cat “Modern Hex” trade dress as well as corporate and product identity used herein, are trademarks
of Caterpillar and may not be used without permission.