100% found this document useful (1 vote)
523 views12 pages

Olt Configuration

The document provides examples of basic commands for checking information and configurations on an Huawei OLT, including commands to check uptime, boards, memory/CPU usage, temperatures, find ONTs by SN, check ONT status, histories, MAC addresses, power levels, versions, IP settings, port status, services per ONT, ping from ONT, reboot, reset to factory, and release/renew DHCP.
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
100% found this document useful (1 vote)
523 views12 pages

Olt Configuration

The document provides examples of basic commands for checking information and configurations on an Huawei OLT, including commands to check uptime, boards, memory/CPU usage, temperatures, find ONTs by SN, check ONT status, histories, MAC addresses, power levels, versions, IP settings, port status, services per ONT, ping from ONT, reboot, reset to factory, and release/renew DHCP.
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 12

NETWORKIN

G.FROM.ZE
RO
Keep Your Spirit To Learn , and Never Give
up To Learn
WRITTEN BY NETWORKINGFROMZERO MARCH 31, 2017

GPON – BASIC COMMAND


OLT HUAWEI
Continuing previous article about some Basic Command in OLT ZTE.
Now, it’s time to share about some basic Commands at OLT Huawei.
Nowadays GPON Technologies have adopted to many brands Like
Cisco , Alcatel Lucent / Nokia , Huawei , ZTE , Fiberhome , and etc.

I have knowledge with some brands like ZTE , Huawei , Fiberhome ,


and Alcatel Lucent. but mostly with ZTE and Huawei. At Least Their
Concept is all same.

That’s same like Topology Below :


There is Always OLT and ONT.

Okay , Here we go of some basic Commands At OLT Huawei.

CHECKING OLT UPTIME


OL01#display sysuptime
System up time: 324 day 20 hour 55 minute 38 second

CHECKING OLT BOARD


OL01#display board 0
————————————————————————-
SlotID BoardName Status SubType0 SubType1 Online/Offline
————————————————————————-
0
1 H805GPFD Normal
2 H805GPFD Normal
3 H805GPFD Normal
4 H805GPFD Normal
5 H805GPFD Normal
6 H805GPFD Normal
7 H802SCUN Active_normal –> Control Module

8 H802SCUN Standby_normal –> Control Module


9 H805GPFD Normal
10 H805GPFD Normal
11 H805GPFD Normal
12 H805GPFD Normal
13 H805GPFD Normal
14 H805GPFD Normal
15 H805GPFD Normal
16 H805GPFD Normal
17 H801X2CS Normal –> Uplink Module

18 H801X2CS Normal –> Uplink Module

19 H801PRTE Normal
20 H801PRTE Normal
————————————————————————-

OL01#

CHECKING OLT PROCESSOR AND MEMORY PER


SLOT
OL01#display mem 0/1
Memory occupancy: 33%

OL01#display cpu 0/1


Send message for inquiring board cpu occupancy successfully, board
executing…
CPU occupancy: 15%
OL01#

CHECKING OLT TEMPERATURE


OL01#display temperature 0
SlotID: 1 BoardName: H805 Temperature: 42C( 107F)
SlotID: 2 BoardName: H805 Temperature: 41C( 105F

FINDING ONT BY SN NUMBER


OL01#display ont info by-sn ABCDEF
—————————————————————————–
In Huawei port 1 = port 0 at system
F/S/P : 0/1/0 (remember) this ONT Meaning that locate at
slot 1 port 0 onu id 2

ONT-ID :2
Control flag : active
Run state : offline
Config state : initial
Match state : initial
DBA type : SR
ONT distance(m) :–
ONT battery state :–
Memory occupation :–
CPU occupation :–
Temperature :–
Authentic type : SN-auth
SN : ABCDEF (HWTC-07930A53)
Management mode : OMCI
Software work mode : normal
Isolation state : normal
ONT IP 0 address/mask : –
Description : IRONMAN
Last down cause : dying-gasp –> down caused by dying gasp
(dying-gasp = ont off )

Last up time : 2016-11-11 17:52:08+07:00 –> Log Last


Uptime

Last down time : 2016-11-15 09:23:27+07:00


Last dying gasp time : 2016-11-15 09:23:27+07:00
ONT online duration : –
Type C support : Not support
Interoperability-mode : Unknown

CHECKING ONT STATUS


OL01#display ont info 0 1 0 all
—————————————————————————–
F/S/P ONT SN Control Run Config Match Protect
ID flag state state state side
—————————————————————————–
0/ 1/0 1 ABCDEF deactivated offline initial initial no
0/ 1/0 2 REZABU active offline initial initial no —
0/ 1/0 4 BAREZU active online normal match no –> ONT
online

CHECKING ONT HISTORY LOGS


OL01#config
OL01(config)#interface gpon 0/1
OL01(config-if-gpon-0/1)#display ont register-info 0 1
——————————————————————————
Index : 10
Auth-type : SN-auth
SN : ABCDEF (HWTC-19698F53)
TYPE : 245H
UpTime : 2016-11-02 16:56:37+07:00
DownTime : 2016-11-04 07:52:15+07:00
DownCause : ONT dying-gasp
——————————————————————————
Index :9
Auth-type : SN-auth
SN : ABCDEF (HWTC-19698F53)
TYPE : 245H
UpTime : 2016-10-31 22:29:05+07:00
DownTime : 2016-11-02 16:42:36+07:00
DownCause : ONT dying-gasp
——————————————————————————
Index :8
Auth-type : SN-auth
SN : ABCDEF (HWTC-19698F53)
TYPE : 245H
UpTime : 2016-10-29 00:25:35+07:00
DownTime : 2016-10-31 22:13:03+07:00
DownCause : ONT dying-gasp

CHECKING ONT MAC ADDRESS


OL01#display mac-address port 0/1/0 ont 2
———————————————————————–
SRV-P BUNDLE TYPE MAC MAC TYPE F /S
/P VPI VCI VLAN ID
INDEX INDEX
———————————————————————–
2389 – gpon aaaa-bbbb-cccc dynamic 0 /1 /0 2 2 122
2388 – gpon bbbb-aaaa-cccc dynamic 0 /1 /0 2 1 212
———————————————————————–
Total: 2
Note: F–Frame, S–Slot, P–Port, F/S/P indicates PW Index for PW,
A–The MAC address is learned or configured on the aggregation port,
VPI indicates ONT ID for PON, VCI indicates GEM index for GPON,
v/e–vlan/encap, pritag–priority-tagged,
ppp–pppoe, ip–ipoe, ip4–ipv4oe, ip6–ipv6oe

OL01#

CHECKING ONT POWER


OL01#config
OL01(config)#interface gpon 0/1
OL01(config-if-gpon-0/1)#display ont optical-info 0 all
—————————————————————————–
ONT Rx power Tx power OLT Rx
ONT Temperature Voltage Current
ID (dBm) (dBm) power(dBm) (C) (V) (mA)
—————————————————————————–
4 -23.10 2.30 -24.21 56 3.260 13
6 -21.08 2.28 -21.49 44 3.240 13

CHECKING ONT VERSION


OL01#display ont version 0 1 0 4
————————————————————————–
F/S/P : 0/1/0
ONT-ID :4
Vendor-ID : HWTC
ONT Version : 49
Product-ID :4
Equipment-ID : 24
Main Software Version : V3R0
Standby Software Version : V3R0
OntProductDescription : EchoLife
Support XML Version : 1.3.
OL01#

CHECKING ONT IP (ROUTING MODE)


OL01#display ont wan-info 0/1 0 4
———————————————————————
F/S/P : 0/1/0
ONT ID :4
———————————————————————
Index :1
Name : OLT_C_INTERNET_DHCP_WAN
Service type : Internet
Connection type : IP routed
IPv4 Connection status : Connected
IPv4 access type : DHCP
IPv4 address : 1.2.3.4
Subnet mask : 255.255.255.0
Default gateway : 1.2.3.1
Manage VLAN : 212
Manage priority :0
Option60 : Yes
Switch : Enable
MAC address : BBBB-AAAA-CCCC
Priority policy : Specified
L2 encap-type : IPoE
IPv4 switch : Enable
IPv6 switch : Disable
———————————————————————
OL01#

CHECKING ONT PORT STATUS


OL01#config
OL01(config)#interface gpon 0/1

OL01(config-if-gpon-0/1)#display ont port state 0 4 eth-port all


————————————————————————–
ONT-
ID ONT ONT Speed(Mbps) Duplex LinkState RingStatus
port-ID Port-type
————————————————————————–
4 1 GE – – down –
4 2 GE 100 full up –
4 3 GE – – down –
4 4 GE – – down –
————————————————————————–
OL01(config-if-gpon-0/1)#

CHECKING ONT CONFIGURATION


OL01#display current-configuration ont 0/1/0 4
#
[gpon]
<gpon-0/1>
interface gpon 0/1
ont add 0 4 sn-auth “ABCDEF” omci ont-lineprofile-id 5
ont-srvprofile-id 1 desc “HULK”
ont ipconfig 0 4 dhcp vlan 212 priority
ont internet-config 0 4 ip-index 0
ont wan-config 0 4 ip-index 0 profile-id 1
ont port route 0 4 eth 1 enable –> routing mode

ont port native-vlan 0 4 eth 2 vlan 122 priority 0 –> bridging mode

ont port native-vlan 0 4 eth 3 vlan 122 priority 0 –> bridging mode

ont port route 0 4 eth 4 enable –> routing mode


#
[bbs-config]
<bbs-config>
service-port 2677 vlan 212 gpon 0/1/0 ont 4 gemport 1 multi-service
user-vlan 212 tag-transform translate inbound traffic-table index 20
outbound
traffic-table index 20
service-port 2678 vlan 122 gpon 0/1/0 ont 4 gemport 2 multi-service
user-vlan 122 tag-transform translate inbound traffic-table index 0
outbound traffic-table index 0
return
OL01#

CHECKING ONT CONFIGURATION PER-PORT


OL01#display current-configuration port 0/1/1
#
[gpon]
<gpon-0/1>
interface gpon 0/1
port 1 ont-auto-find enable –> Configuring this to detect your
unregister ONU automatically

CHECKING HOW MANY SERVICES PER-ONT


OL01#display service-port port 0/1/0 ont 4
{ <cr>|e2e<K>|gemport<K>|sort-by<K> }:

Command:
display service-port port 0/1/0 ont 4
Switch-Oriented Flow List
—————————————————————————–
INDEX VLAN VLAN PORT F/ S/ P
VPI VCI FLOW FLOW RX TX STATE
ID ATTR TYPE TYPE PARA
—————————————————————————–
2677 212 common gpon 0/1 /0 4 1 vlan 212 20 20 up
2678 122 common gpon 0/1 /0 4 2 vlan 122 0 0 up
—————————————————————————–
Total : 2 (Up/Down : 2/0)
Note : F–Frame, S–Slot, P–Port,
VPI indicates ONT ID for PON, VCI indicates GEM index for GPON,

OL01#

YOU CAN PING FROM YOUR ONT :P


OL01#config
OL01(config)#interface gpon 0/1
OL01(config-if-gpon-0/1)#ont remote-ping 0 4 ip-address 8.8.8.8
OL01(config-if-gpon-0/1)#
—————————————–
ONT remote-ping information
—————————————–
F/S/P : 0/ 1/0
ONT-ID :4
ONT IP Index :0
IP address of ping : 8.8.8.8
Transmit packets : 4
Receive packets :4
Lost packets :0
Lost packets ratio(%): 0
Min delay(ms) : 31
Max delay(ms) : 31
Average delay(ms) : 31
Error Code :–
—————————————–

REBOOT ONT
OL01#config
OL01(config)#interface gpon 0/1
OL01(config-if-gpon-0/1)#ont reset 0 4

RESET FACTORY ONT


OL01#config
OL01(config)#interface gpon 0/1
OL01(config-if-gpon-0/1)#ont factory-setting-restore 0 4

HOW TO RELEASE RENEW ONT AS DHCP CLIENT


OL01#config
OL01(config)#interface gpon 0/1
OL01(config-if-gpon-0/1)#ont ipconfig 0 4 dhcp reset

CHECKING RX LEVEL FOR OLT UPLINK


OL01#config
OL01(config)#interface giu 0/18
OL01(config-if-giu-0/18)#display port ddm-info 0
Temperature(C) : 38.640000
Supply voltage(V) : 3.260000
TX bias current(mA) : 38.000000
TX power(dBm) : 1.095110
RX power(dBm) : -14.659738
OL01(config-if-giu-0/18)#quit
OL01(config)#quit
OL01#

RESET SLOT
OL01#config

OL01(config)#board reset 0/1

HOW TO FIND ONT BY MAC


OL01#display location aaaa-bbbb-cccc
{ <cr>|fabric<K>|ont<K> }:

Command:
display location 4cf9-5dd3-1914
It will take several minutes, and console may be timeout, please use
command idle-timeout to set time limit
Are you sure to query MAC address location ? (y/n)[n]:y
———————————————————————–
SRV-P BUNDLE TYPE MAC MAC TYPE F /S
/P VPI VCI VLAN ID
INDEX INDEX
———————————————————————–
5493 – gpon aaaa-bbbb-cccc dynamic 0 /6 /6 50 1 203
———————————————————————–

If U want to Explore More about other, My advice is using “?”


symbol.

I Hope this article can help you sometime.

You might also like