Nikuni KTM Series Pumps

( Micro Bubble Generator for DAF System )

Client :
Project :
Model : KTM50S1-000 (SS304 material)

Date :
Doc. No. :
Revision No. :

Japan Headquarters :
843-5, Kuji, Takatsu-Ku, Kawasaki-Shi,
Kanagawa, Japan Post-code 213-0032
URL : http://www.nikuni.co.jp

Phone: +81-44-833-6500 (English)

+81-44-833-1121 (Japanese)
Fax : +81-44-833-6482
MAIN OFFFICE :
843-5 KUJI, TAKATU-KU, KAWASAKI, KANAGAWA, JAPAN 2130032
TEL : +81(0)-44-833-6500 FAX: +81(0)44-833-6482 NIKUNI BUBBLE GENERATOR FOR DAF SYSTEM

NIKUNI KTM (DAF) PUMP DATA SHEET

Company 0 Date 00-Jan-1900
Project 0 Data sheet No. 0
Service 0 Rev.
Item No 0 PID No.
No.Operating 0 No.Spare 0 Total Required 0
Pump Model KTM50S1-000 (SS304 material)
Pump Type Coupling Type (Base plate, Coupling set & Coupling guard only)
PROCESS AND PERFORMANCE DATA
Conditions of Service, Each Pump
Fluid Treated Water Design Capacity (L/min / gpm) /
Normal Capacity (L/min / m3/Hr) 133 / 8.0 Suction Press. (MPa / bar) -0.03 / -0.3
Temperature (℃) Disch. Press. (MPa / bar) /
Specific Gravity (at P.T.) Differential Press. (MPa / bar) /
Viscosity (at P.T. MPa・s) Total Head (m / bar) 30 or 40 / 3 or 4
Air Flow rate (NL/min / Nm3/Hr) 11 / 0.64 Differential Head (m / bar)
NPSH Ava. (m) NPSH Req. (m)
Motor Driver
*Electric motor should be prepared by purchaser
Phase Output (kW / HP) 5.5kW / 7 HP Frequency 50 Hz
Voltage Pole 4 Speed 1500 min-1
Type
* Original base plate will be fixed to IEC Motor frame size 132S .
Connection
(Suction.) Size 50 A Rating JIS 10K
(Discharge.) Size 50 A Rating JIS 10K
10K
Materials (Wetted parts)
Casing SCS13 Shaft SUS304 Cover O-ring PTFE
Impeller SUS304 Side plate N/A Slinger NBR
Cover SCS13 Mechanical Seal Sic - Sic , PTFE
Painting
MUNSELL N3

Remarks
Accessory :
Air In-take nozzle.
Please refer to attached recommendation of the air-parameter & guages ranges and other accessories.

REV. DATE COMMENT DESCRIPTION DRAWN BY CHECK BY APPROVED BY

 MODEL:KTM50S1,S2,S3 50Hz

Dimension

Note:
1. For KTM50S3

*2 (40)
*3 (125)
*1 : M12
*2 : 40mm
*1 (4-M10) *3 : 150mm
*4 : 38mm

*4 (31)

Coupling Dimension for KTM50S(F)1, S2(F2) & S3(F)

Coupling Dimension (unit:mm) Applicable motor frame size for Original base-plate.

kw A B C D E F SS kW IEC Frame
5.5,7.5 45 45 90 38 41.3 10 24 5.5 132S
11,15 55 55 120 42 45.3 12 40 7.5 132M
11 160M
15 160L

Demension & net weight Unit:mm

Model Kw HP S D PR PY FA FB FS FC MH L MA MR SS VE VF VM VN VS VT VZ KL Weight
KTM50S1 5.5 7.0 50A 50A 285 160 130 55 150 230 204 836 210.5 239 24 324 448 352 690 121 20 12 189 90
KTM50S2 7.5 10 50A 50A 285 170 130 55 160 240 204 874 229.5 258 24 324 448 352 690 121 20 12 189 110
KTM50S3 11 15 50A 50A 285 170 130 55 169 240 245 1027.5 302 323 40 368 614 404 878 132 20 15 257.5 125
*Approx. Packing weight
(Motor weight not included)

Sectional Drawing

Material
No. NAME OF PARTS SET MATERIALS
021 Ball Bearing 1 㻌SUJ
022 Ball Bearing 1 㻌SUJ
025 Bracket 1 㻌FC200
027 Bearing Gland 1 㻌㻿㻼㻯
051 Mechanical Seal 1 SiC - SiC
074 Key 1 䚷S45C
081 Slinger 1 㻌NBR
102 Casing 1 㻌㻿㻯㻿㻝㻟
103 Cover 1 㻌㻿㻯㻿㻝㻟
107 Impeller 1 㻌SUS304
108 Shaft 1 㻌SUS304
113, 114 Key, washer & nut 1 㻌SUS304
116 Impeller Key 1 㻌㻿㼁㻿㻟㻝㻢
123 Cover O-Ring 1 㻌㻼㼀㻲㻱

Copyright© 2012 All Right Reserved Nikuni Co., Ltd.

 PC-KTM50S15002

PUMP SUPPOSITION CURVE 50Hz

Model KTM50S1

10
NPSHreq.(m)

8
6 NPSH
4
2
0
0 50 100 150 200 250 300
120 60

100 50

Total Head

80 40
Effect
Total Head(m)

Effect(%)
60 30

40 20

20 10

0 0
10.0 0 50 100 150 200 250 300

8.0
Output(kW)

6.0 Output
4.0

2.0

0.0
0 50 100 150 200 250 300
Capacity(L/min)

NIKUNI Co.,Ltd.
 Accessories

Air Intake Nozzle (Included in every package )

How to connect the nozzle to Air Flow Meter (Air Intake Nozzle will be attached to every pump)
Applicalbe Model
(Standard) Dia. (E) Length (L1) Length (L2) Length (L) Dia. (D)

KTM15 (F)(N)(D) R 3/8B 121 73 157 R 1/4B

KTM20 (F)(N)(D) R 3/8B 121 88 162 R 1/4B

L1
KTM25 (F)(N)(D) R 3/8B 121 97 167 R 1/4B
B
R 1/4B
L1

KTM32 (F)(N)(D) R 3/8 121 114 172

B
KTM40 (F)(N)(D) R 3/8 121 120 177 R 1/4B
B
KTM50 (F)(S)1,2,3 R 3/8 129 210 268 R 1/4B
L2
L2

Applicable Model
(Large-scaled Type) Dia. (E) Length (L1) Length (L2) Length (L) Dia. (D)

KTM65S2 / F2 Rc 3/8 183 240 304 Rc 3/8

Standard Type Large-scaled Tpye KTM80S / F Rc 3/8 193 240 319 Rc 3/8
* In case of KTM80S / F model, connect “E” part with Bushing (3/4 x 3/8)

1) Loosen the nuts of the lower pipe joint to allow a nipple to freely move.
2) Mark the pipe bending direction on the pipe surface Noted :
between the upper and lower pipe joints. Fitting connections &
3) Wind a sealing tape around the lower pipe joint’s nipple of the
Air Flow meter should be
suction nozzle, insert it into the nozzle junction of the pump,
and turn the nipple to firmly fix it. prepared by purchaser
4) Turn the pipe to align the mark on the pipe surface so that the
bend nose (gas discharge port) of the pipe will be directed to
the center of the impeller. 
5) Tighten the nuts of the lower pipe joint firmly. Air In-iake Nozzle will be
Make sure that the suction nozzle is not manually rotated. attached to every pump
6) Rotate the motor manually (rotate the shaft end of the motor
with a screwdriver) to make sure that the pipe nose of the
nozzle is not interfering with the impeller.


Recommended Accessories (To be prepared by Purchaser)

Air Parameter Guages
0

Compound Guage Pressure Guage

Minus 0.1 MPa to + 0.25MPa 0 MPa to + 1.0MPa
Minus 1.0 Bar to + 2.5 Bar 0 Bar to + 10 Bar
Minus 15psi to + 35 psi 0 psi to + 150 psi

Operation air flow rate & Air Parameter ranges

50Hz Frequency 60Hz Frequency
Applicalbe Model Water Flow Rate Operation Air flow rate Air Flow Meter Range Water Flow Rate Operation Air flow rate Air Flow Meter Range
(Standard) m3/Hr x 4Bar (N䞉L/min) (N䞉L/min) m3/Hr x 4Bar (N䞉L/min) (N䞉L/min)
KTM20 (F)(N)(D) 1.0 1.3 0 to 5 1.3 1.7 0 to 5
KTM25 (F)(N)(D) 1.5 2.0 0 to 5 2.5 3.3 0 to 5
KTM32 (F)(N)(D) 3.0 4.0 0 to 10 4.0 5.3 0 to 10
KTM40 (F)(N)(D) 4.8 6.4 0 to 10 7.0 9.3 0 to 20
KTM50S1 / F1 8.0 10.6 0 to 20 11.5 15.0 0 to 30
KTM50S2 / F2 12.0 16.0 0 to 20 15.0 20.0 0 to 40
KTM50S3 / F3 15.0 20.0 0 to 30 18.0 24.0 0 to 40
KTM65S2 / F2 20.0 26.6 0 to 40 28.0 38.0 0 to 60
KTM80S / F 42.0 56.0 0 to 80 58.0 78.0 0 to 100

Copyright© 2012 All Right Reserved Nikuni Co., Ltd.

 Excess Air Device / Separation Tank

The KTM Series pump user manual must be fully read and understood before operating the pump.
Failure to do so may result in death, serious injury, or property damage. This page is intended for a
basic understanding of the KTM startup operation and is not a substitute for the user manual.

PRE-OPERATION CHECK (POWER OFF)

1) Prime KTM with effluent or water
2) Fully open Suction valve and Discharge valve. Do not run KTM with these valves closed.

STARTING THE KTM

1) Discharge side adjustments:
Slowly tighten the Discharge valve until the discharge pressure falls within the desired range
of 0.3MPa to 0.4Mpa (approximately 3 bar to 4 bar) with reference to the Pressure gauge.
In the case where the Discharge valve (or KTM) is located far from the flotation tank, bubbles
will tend to grow larger. In order to maintain microbubble size, an additional control valve
should be installed on the flotation tank side to control the discharge pressure.

2) Suction side adjustments:

Check to see if the Compound gauge indicates a negative suction pressure between the range
of -0.02MPa to -0.03MPa (approximately -0.2 bar to -0.3 bar). If the pressure is higher than
this range, slightly tighten the Suction valve to bring the pressure into the range stated above.

3) Air injection adjustments:

Open the knob of Air-Parameter (Air flow meter) and adjust to an air flow rate that is 8% of
the water flow rate.

AIR FLOW METER

AIR IN-TAKE NOZZLE PRESSURE GUAGE

( ATTACHED WITH EVERY PUMP) TO FLOATATION TANK

COMPOUND GUAGE
DISCHARGE CONTORL VALVE
FROM FLOTATION TANK
(TREATED WATER)
KTM
SUCTION CONTORL VALVE

KTM (KARYU TURBO MIXER)
NOTES : KTM & AIR IN-TAKE NOZZLE WILL BE SUPPLIED BY NIKUNI
OTHERS ACCESSORIES CAN SUPPLY AS OPTIONAL CASE.

In case of mini bubbles occur and effect to flotation process,

please consider installing Excess Air Device / Separation Tank as shown in next page.

Copyright© 2012 All Right Reserved Nikuni Co., Ltd.

 Excess Air Device / Separation Tank

Reference P&ID for DAF System

&RDJXODQW)ORFFXODQWSURFHVV

Wastewater Influent Treated Water

)ORWDWLRQWDQN
UU
UU

Excess air release

Excess Air Device /

Air Separation tank

Air
Pressurized Water

To Flotation Tank

KTM
KTM

To KTM
.DU\X7XUER0L[HU

Recommended Separation Tank Capacity

Excess Air Release

(Install a contorl valve as to Model A (mm) B (mm) Capacity (Liter)
adjust the release of air amount)
KTM20N(F)(D) 100 260 2
KTM25N(F)(D) 120 350 4
KTM32N(F)(D) 260 400 20
KTM40N(F)(D) 260 400 20
(B)

( A)
KTM50S(F)1,S(F)2,S(F)3 300 850 60
KTM65S(F)2 450 900 140
KTM80S(F) 450 900 140
Pressurized Water Outlet

Pressurized Water Inlet

Copyright© 2012 All Right Reserved Nikuni Co., Ltd.