Condenser PDF

Condensers
The condenser is a two-phase flow heat exchanger

(HEX) where the heat (generally latent heat) is
removed by conversion of vapor into liquid with
the help of coolant.
By: Prof K. M. Joshi,

Assi. Professor, MED,
SSAS Institute of Technology, Surat.
Its main function in thermal power plant is to condense the
www.joshikandarp.webs.com
exhaust stream from the turbine and thus recover the high-
quality feed water for reuse in the plant.
INTRODUCTION
Why it is necessary…???
Feed from condenser for boiler reduces the cost of power

generation as the condensate is supplied at higher
temperature.
The deposition of salt in the boiler is prevented with the use
of condensate instead of using the feed water from outer
source which contains salt.
Reduces the capacity of the feed water cleaning system.
The use of condenser in steam power plant reduces the
overall cost of generation by increasing the thermal
efficiency of the power plant.
Cont...
Thermodynamics point of view…

The partial vacuum and low back pressure is developed in
condenser. The specific steam consumption of the plant
decreases as the available enthalpy drop or work developed
per kg of steam increases with the decrease in back pressure
by using condenser.
By lowering the condenser

operating pressure, following will
occur:
Increased turbine output
Increased plant efficiency
Reduced steam flow
(for a given plant output)
Type of Condenser
There are mainly two types:

Indirect contact: condensing vapor and coolant are
separated by a solid surface
shell-and-tube: condensation inside or outside, vertical or
horizontal
plate: limited applications
air-cooled: condensation in tubes, air blown over tubes
(usually finned)
Direct contact: condensing vapor and coolant are in direct
contact
vapor bubbled into a poof of liquid
liquid sprayed into vapor
packed-column: liquid flows as a film over a "packing
material" against upward flow of vapor.
Indirect / Surface Condenser
The surface condensers may be classified according to
(a) Number of water passes : single or multipass.
(b) Direction of condensate flow and tube arrangement: down flow,
and central flow as shown below.
Mixing or Jet Type Condensers:
The jet condensers are mainly divided as parallel flow

and counter flow jet condensers.
In parallel flow condensers, the steam and cooling
water flow in the same direction whereas they flow in
opposite directions in counter flow condensers.
Mixing type condensers are mainly

classified into three categories depending upon the
arrangement used for the removal of condensate as
low level, high level and ejector condenser. These are
rarely used in modern high capacity power plants.
AIR LEAKAGE, ITS EFFECTS ON PERFORMANCE OF CONDENSER
The sources of air :

1. The air leaks through the joints, packings and glands into the
condenser where the pressure is below the atmospheric pressure.
2. The feed water contains air in dissolved condition. The
dissolved air gets liberated when the steam is formed and it is
carried with the steam into the condenser.
The effects of air leakage:

1. It increases the pressure in condenser or back pressure of the
prime-mover and reduces the work done per kg of steam.
2. The pressure of air lowers the partial pressure of steam and its
corresponding temperature. The latent heat of steam increases at
low pressure. Therefore, more quantity of cooling water is
required to condense one kg of steam as quantity of latent heat
removed is more.
There is grater possibility of under-cooling the condensate
with the reduction in partial pressure of steam due to the presence
of air. This phenomenon reduces the overall efficiency of the
power producing plant.
3The heat transfer rates are greatly reduced due to the presence of
air because air offers high resistance to heat flow. This further
necessitates the more quantity of cooling water to maintain the
heat transfer rates. Otherwise, it reduces the condensation rate
and further increases the back pressure of the prime mover.
Removal of Air:
It is obvious from the above discussion that the preventive
measures should be taken to remove leaking air from the
condenser to avoid its bad effects.
The air from the condenser is removed with the help of
airpumps. The primary function of the air pump is to maintain the
vacuum in the condenser which corresponds to the exhaust steam
temperature by removing the air. Another function of the pump is
to remove the condensate coming out from the bottom of the
condenser.
An air-pump which removes both air and condensate together
is called 'Wet Air-Pump' while the air-pump which removes only
the moist air is known as 'Dry-Air-Pump‘.
DALTON'S LAW OF PARTIAL PRESSURE USED FOR CONDENSER ANALYSIS
Dalton's law of partial pressure states that
“The total pressure exerted by a mixture of gases or

a mixture of gas and vapour is equal to the sum of
individual partial pressures of the constituents of the
mixture; if individual partial pressures of the constituents
of the mixture when individual alone occupies total
volume, occupied by mixture having the same temperature
of mixture.”
The total pressure in the condenser is the sum of the partial
pressures of steam and air.

Condenser PDF

Uploaded by

Copyright:

Available Formats

Condenser PDF

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Condenser PDF

Uploaded by

Copyright:

Available Formats

Condensers

The condenser is a two-phase flow heat exchanger

By: Prof K. M. Joshi,

Feed from condenser for boiler reduces the cost of power

Thermodynamics point of view…

By lowering the condenser

There are mainly two types:

The jet condensers are mainly divided as parallel flow

Mixing type condensers are mainly

The sources of air :

The effects of air leakage:

Dalton's law of partial pressure states that

“The total pressure exerted by a mixture of gases or

You might also like