XTS - Speed Dome IP Camera Quick Guide

XTS Speed Dome IP Camera Quick Guide
This guide is for quick installing and connecting the XTS Speed Dome IP Camera. For more details, please refer to Green Link Light indicates good network connection.
the User’s Manual of the camera in the supplied CD. Orange Activity Light flashes for network activity indication.
Camera’s Connectors Alarm I/O Connection

Please refer to the diagram and pin definition tables below for alarm I/O connection.
Pin Definition Pin Definition Pin Definition Pin Definition

1 Alarm Out NO 1 4 GND 7 Alarm Out COM 2 10 Alarm In 3
2 Alarm Out NC 1 5 Alarm Out NO 2 8 GND 11 Alarm In 2
3 Alarm Out COM 1 6 Alarm Out NC 2 9 Alarm In 4 12 Alarm In 1
Audio I/O Connection

Please refer to the diagram and the pin definition table below for audio I/O connection.
Pin Definition
Indoor Outdoor 1 Audio Out
2 GND
Pin Connector Definition 3 Audio In
1 Alarm I/O Alarm I/O connection
2 Default Button Press the button with one figure for at least 20 seconds to restore the system. Before Login to the Camera
3 Audio I/O Audio I/O connection A client program will be automatically installed to the PC when connecting to the camera. Before logging in to the
4 RJ-45 For network and PoE+ connections camera, please ensure downloading the ActiveX control is allowed by either changing the ActiveX controls and
5 Power (AC 24V) Power connection plug-ins or setting Internet’s security level to default. For further details, please refer to the User’s Manual in the
Insert the microSD card into the card slot to store videos and snapshots.
6 microSD Card Slot supplied CD.
Do not remove the microSD card when the camera is powered on.
ActiveX Controls and Plug-ins Settings Internet Security Level
NOTE: It is not recommended to record with the microSD card for 24/7 continuously, as it may not be able to
Step 1: Start the Internet Explorer (IE). Step 1: Start the IE Internet Explorer (IE).
support long term continuous data read/write. Please contact the manufacturer of the microSD card for Step 2: Select <Tools> from the main menu of the Step 2: Select <Tools> from the main menu of the
information regarding the reliability and the life expectancy. browser. Then click on <Internet Options>. browser. Then click on <Internet Options>.
Step 3: Click on the <Security> tab and select Step 3: Click on the <Security> tab and select
Power Connection <Internet>, and click on <Custom level> to <Internet>.
To power up the camera, connect the AC 24V power adaptor to the power connector of the camera and the power change ActiveX settings. Step 4: Down the page, click on <Default Level> and
outlet. Refer to the diagram and the pin definition table below for connection. Alternatively, users can use an Ethernet Step 4: Set “ActiveX controls and plug-ins” items to <OK> to confirm the setting. Close the browser
<Prompt> or <Enable>. window, and open a new one later for
cable and connect it to the RJ-45 connector of the camera and an IEEE 802.3at 60W PoE+ switch.
accessing the IP camera.
Pin Definition
1 AC 24V 1 Camera Login
2 GND The default IP address of the camera is: 192.168.1.100. Therefore, to access the camera for the first time, please set
3 AC 24V 2 the IP address of the PC as: 192.168.1.XXX; for example:
Ethernet Cable Connection IP Address: 192.168.1.50

Connect one end of the Ethernet cable to the RJ-45 connector of the camera, and plug the other end of the cable to Subnet Mask: 255.255.255.0
the network switch or PC.
Login ID & Password
NOTE: In some cases, Ethernet crossover cable might be needed when connecting the camera directly to the  Key in the camera’s IP address in the URL bar of the web browser window and hit “Enter”.
PC.  Enter the default username (root) and password (pass) in the prompt request dialogue. Note that username is
case sensitive.
NOTE: Check the status of the link indicator and activity indicator LEDs. If the LEDs are unlit, please check
the LAN connection.
Install the ActiveX Control
 After connecting to the camera, the request for installing the ActiveX control will appear just below the URL bar.
 Right click on the information bar and click on <Install ActiveX Control…> to permit ActiveX control installation.
 In the pop-up security warning window, click on <Install> to start downloading DC Viewer software on the PC. XTS Speed Dome IP Camera
 Click on <Finish> after DC Viewer installation is completed.
Browser-based Viewer Quick Guide

The main page of the IP camera user interface is as shown below.
www.xtscorp.com

XTS - Speed Dome IP Camera Quick Guide

Uploaded by

Copyright:

Available Formats

XTS - Speed Dome IP Camera Quick Guide

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

XTS - Speed Dome IP Camera Quick Guide

Uploaded by

Copyright:

Available Formats

XTS Speed Dome IP Camera Quick Guide

Camera’s Connectors Alarm I/O Connection

Pin Definition Pin Definition Pin Definition Pin Definition

Audio I/O Connection

Ethernet Cable Connection IP Address: 192.168.1.50

Browser-based Viewer Quick Guide

You might also like