Desch V-Belt Pulleys

Download as pdf or txt
Download as pdf or txt
You are on page 1of 16
At a glance
Powered by AI
The document discusses V-belt pulley drives, their components, and design considerations.

V-belt pulleys are used in V-belt drives to transmit power between two shafts through friction.

DESCH V-belt pulleys have advantages like quiet running, good damping, rupture safety, easy assembly and low maintenance.

DESCH V-Belt pulleys

Screw-on hubs, Welded hubs

KS 12 – GB
V-belt pulley

V-belt drives are frictionally engaged V-belt pulleys with cylindrical hole are
traction mechanism gears consisting in balanced on one level quality grade
their simplest form of two V-belt pul- G 16 according to DIN ISO 1940;
leys and V-belts. Transmission ratios dw < 400 mm with an operating speed
of 8:1 to 1:8 are possible with a power n = 1500 rpm; dw > 400 mm with
of up to 1000 kW. With an extensive v = 30 m/s. Pulleys for taper bushes corre-
calculation program we determine the spond to quality grade G 3 according to
economically optimum drive from the DIN ISO 1940 balanced on one level; for
large number of combinations which are dw < 400 mm with n = 1.500 rpm;
technical feasible. Prices and delivery for dw > 400 mm with v = 30 m/s. The
times are favourable if V-belt pulleys balancing is performed without groove
from the range in stock can be used. on a smooth balancing mandrel, which
corresponds to the half-wedge balancing
mode. Other types of balancing, such as
DESCH V-belt pulleys full-wedge, by agreement. We recom-
The DESCH V-belt pulleys have many mend: balancing on 2 levels G 6.3 for ope-
advantages: quiet running; good rating speed if the circumferential speed
damping of impact torques and rota- is v > 30 m/s or the dw b2 ratio is < 4 and
ry vibrations; rupture safety because v is > 20 m/s. If nothing different is
V-belts slip at over load; easy assem- indicated, the ready-drilled holes of
bling; low-maintenance. In normal case the V-belt pulleys are given a tolerance
DESCH pulleys are of the material EN-GJL of H7 and are grooved for feather keys
200 and are standardised on the basis Fig. 2
according to DIN 6885/1. Max. out- Fig. 1 Fig. 3

of DIN 2211 and 2217 respectively. side diameter of pulleys 3.500 mm.

Fig. 4

General instructions In addition to V-belts for a wide variety


When selecting the V-belt profile and the of profiles, we sell narrow V belts to DIN
pulley diameter the following points are 7753, Part 1 (Fig.1) and USA Standard RMA/
important: MPTA in covered and raw-edged design
Maximum circumferential 1. Do not go below minimum pulley (Fig.3), compound V-belts (Fig.4) and
speeds: diameter (p.8) (service life, economic V-belts according to DIN 2215 (Fig.2). The
efficiency) latter are not economic and should no
Pulley 1T 2T V in m/s 2. Use standardised pulley diameter. longer be used in new designs. V-belts
Mate- Select a standardised diameter at
• ° X X 1T = one-piece manufactured in series are resistant to
rial
2T = two-piece least for the largest pulley of the oils and greases provided these are only
EN-GJL • = full pulley drive. present in small quantities, they are heat-
200 42 42 38 28 ◦ = botto
(GG-20) 3. Note belt speed or max. circumfe- resistant to 70°C ambient temperature,
pulley
EN- GJS X = arm pulley rential speed of belt pulley. For electrically conductive and dust-proof.
400 higher speeds other material grades
60 60 54 -
(GGG can be supplied.
40)
4. Special design possible.

For safety reasons the circumferential


speeds given above may not be exceeded.

2
Taper bushes
with groove according to DIN 6885, Part 1

DESCH Taper bushes are used to fasten pulleys or coulpings to shaft. In the case of
V-belt pulleys this fastening is generally sufficient to transmit the power. An addi-
tional feather key connection is only necessary with extremely high load. Each
taper bush is equipped with a feather key groove for this purpose. The bushes can
be used with shaft tolerances of up to h11 with max. diameter of 30mm. Beyond
this up to h9. Detailed installation instructions are enclosed with each delivery.

bore-ø d2 of the available bushes


Bush No.
mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm
1008 10 11 12 15 16 18 19 20 22 24* 25*
1108 10 11 12 15 16 18 19 20 22 24 25 28*
1210 11 12 14 15 18 19 20 22 24 25 28 30 32
1610/1615 15 16 18 19 20 22 24 25 28 30 32 35 38 40 42*
2012 15 16 18 19 20 22 24 25 28 30 32 35 38 40 42 45 48 50
2517 16 18 19 20 22 24 25 28 30 32 35 38 40 42 45 48 55 55 60 65*
3020 25 28 30 32 35 38 40 42 45 48 50 55 60 65 70 75
3030 35 38 40 42 45 48 50 55 60 65 70 75
3025 35 38 40 42 45 48 50 55 60 65 70 75 80 85 90 95 100*
3535 35 38 40 42 45 48 50 55 60 65 70 75 80 85 90
4030 40 42 45 48 50 55 60 65 70 75 80 85 90 95 100 105 110 115*
4040 40 42 45 48 50 55 60 65 70 75 80 85 90 95 100
4535 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125
4545 55 60 65 70 75 80 85 90 95 100 105 110
5040 70 75 80 85 90 95 100 105 110 115 120 125
5050 70 75 80 85 90 95 100 105 110 115 120 125

Bush No. Hole -ø d2 Groove width b Groove depth t2 > * This hole has a shallow groove
1008 24*/25* 8 2/1,3 ** for hexagon socket screws
1108 28* 8 2
1610/1615 42* 12 2,2
2517 65* 18 2,3
3525 100* 28 4,4
4030 115* 32 5,4

3
Preferred versions for V-belt pulleys
with taper bushes

Bearing of hub to rim:


bü=flush, rü= recessed, v= protruding

Minimum pulley diameter


Proile SPZ / XPZ SPA / XPA SPB / XPB SPC / XPC 3V(9N) / 3VX 5V (15N) / 5VX 8V

da min 63 / 56 90 / 71 140 / 112 224 / 180 63 / 56 140 / 112 335

Proile SPC (J) 9J (3V) 15J (5V) 25J (8V)

da min 250 67 180 335

4
rounded edge

Pulley
Standard sheet
DIN 2211 DIN 2217 DIN ISO 5290 4)
DIN 7753 T1 SPZ/XPZ SPA/XPA SPB/XPB SPC/XPC
DIN 7753 T3 9,5-AVX 10 12,5-AVX 13
DIN 2215/DIN 10 13 17 22 (25) 32
belt proile
2216
DIN ISO Z A B C - D 9N/9J 15N/15J 25N/25J
RMA/MPTA 3V/3VX 5V/5VX 8V
bw 8,5 11 14 19 21 27
b1 1) ≈9,7 ≈12,7 ≈16,3 ≈22 ≈25 ≈32 8,9 15,2 25,4
c 2 2,8 3,5 4,8 6,3 8,1 0,6 1,3 2,5
distance e 2) 12±0,3 15±0,3 19±0,4 25,5±0,5 29±0,5 37±0,6 10,3±0,25 17,5±0,25 28,6±0,4
between f 8±0,6 10±0,6 12,5±0,8 17±1 19±1 24±2 9 13 19
grooves
V-belt DIN 2215 u. 11+0,6 13,8+0,6 17,5+0,6 23,8+0,6 22+0,6 28+0,6
DIN 7753
tmin 8,9 15,2 25,4
inite V-belt DIN 11+0,6 13,8+0,6 17,5+0,6 23,8+0,6 28+0,6 33+0,6
2216
a 34° for ≤ 80 ≤ 118 ≤ 190 ≤ 315 ≤ 355 -
a 36° „dw“ bei - - - - - ≤ 500 ≤ 90
a 38° DIN 2211/7 > 80 >118 >190 >315 >355 >500 ≤150 ≤250 ≤400
a 40° ≤300 ≤400 ≤560
„da“ bei
a 42° DIN ISO 5290 >300 >400 >560
tolerance for α ±1° ±1° ±1° ±0,5° ±0,5° ±0,5° ±0,25° ±0,25° ±0,25°
Compound Number of Rim width b2
V-belt combi- z
nations 3)
- 1 16 20 25 34 38 48 18 26 38
2 2 28 35 44 59,5 67 85 28,3 43,5 66,6
3 3 40 50 63 85 96 122 38,6 61,0 95,2
4 4 52 65 82 110,5 125 159 48,9 78,5 123,8
5 5 64 80 101 136 154 196 59,2 96,0 152,4
3/3 6 76 95 120 161,5 183 233 69,5 113,5 181,0
3/4 7 88 110 139 187 212 270 79,8 131,0 209,6
4/4 8 100 125 158 212,5 241 307 90,1 148,5 238,2
5/4 9 112 140 177 238 270 344 100,4 166,0 266,8
5/5 10 124 155 196 263,5 299 381 110,7 183,5 295,4
4/3/4 11 136 170 215 289 328 418 121,0 201,0 324,0
4/4/4 12 148 185 234 314,5 357 455 131,3 218,5 352,6
4/5/4 13 - - - 340 386 492 141,6 236,0 318,2
5/4/5 14 - - - 365,5 415 529 151,9 253,5 409,8
5/5/5 15 - - - 391 444 566 162,2 271,0 438,4

1) The upper groove widths „b1“ are only precisely defined for V-belt pulleys according to DIN ISO 5290 for compound narrow
V-belts. In the case of grooves according to DIN 2211 and DIN 2217, „b1“ depends in the groove angle.
2) The tolerance of the groove distance for non-successive grooves is double the value given for „e“. (not for compound V-belt
pulleys)
3) Compound narrow V-belts only run in V-belt pulleys with a distance between grooves „e“ according to DIN ISO 5290.
4) Is in accordance with US Engineering Standard RMA/MPTA „Specification for drives using narrow multiple V-belts“

5
Stock V-belt Pulleys for Taper Bushes

SPZ
Efective.Ø Grooves • d2 l Design Weight Bush No. Efective.Ø Grooves • d2 l Design Weight Bush No.
º max. º max.
X X
dw dw
mm mm kg mm mm kg
1 • 25 22 6 rü 12 0,2 1008 1 • 42 25 8 bü 1,6 1610
56
2 • 28 22 6 rü 27 0,3 1008 2 • 42 25 6 rü 3 2,4 1610
1 • 25 22 8 bü 0,25 1008 140 3 • 50 32 2 bü 2,7 2012
60
2 • 28 22 6 rü 27 0,35 1108 4 • 50 32 2 bü 3,1 2012
1 • 28 22 8 bü 0,3 1108 5 • 50 45 2 bü 3,5 2517
63 2 • 28 22 6 rü 6 0,45 1108 1 • 42 25 8 bü 1,9 1610
3 • 28 22 6 rü 18 0,58 1108 2 • 50 32 8 bü 2,6 2012
1 • 28 22 8 bü 0,35 1108 150 3 • 50 32 2 bü 3,3 2012
67 2 • 28 22 6 rü 6 0,41 1108 4 • 50 45 2 bü 3,8 2517
3 • 28 22 6 rü 18 0,56 1108 5 • 50 45 2 bü 4,3 2517
1 • 28 22 8 bü 0,4 1108 1 • 42 25 8 bü 2,1 1610
71 2 • 28 22 6 rü 6 0,48 1108 2 • 50 32 8 bü 3,1 2012
3 • 28 22 6 rü 18 0,64 1108 160 3 • 50 32 2 bü 3,9 2012
1 • 28 22 8 bü 0,45 1108 4 • 60 45 2 bü 4,6 2517
75 2 • 32 25 6 rü 3 0,46 1210 5 • 60 45 2 bü 5,1 2517
3 • 32 25 6 rü 15 0,62 1210 1 • 42 25 8 bü 1,5 1610
1 • 32 25 8 bü 0,5 1210 2 • 50 32 8 bü 2,5 2012
2 • 32 25 6 rü 3 0,57 1210 170 3 • 50 32 4 rü 4 4,2 2012
80
3 • 32 25 6 rü 15 0,75 1210 4 • 60 45 2 bü 5,3 2517
4 • 32 25 6 rü 27 0,9 1210 5 • 60 45 2 bü 5,9 2517
1 • 32 25 8 bü 0,6 1210 1 ° 42 25 8 bü 1,8 1610
2 • 42 25 6 rü 3 0,7 1610 2 ° 50 32 8 bü 2,7 2012
85 3 • 42 25 6 rü 15 0,8 1610 180 3 ° 50 32 8 bü 3,2 2012
4 • 42 25 6 rü 27 0,9 1610 4 • 60 45 2 bü 6,3 2517
5 • 42 25 6 rü 39 1,3 1610 5 • 60 45 2 bü 6,9 2517
1 • 32 25 8 bü 0,7 1210 1 ° 42 25 8 bü 1,8 1610
2 • 42 25 6 rü 3 0,67 1610 2 ° 50 32 8 bü 2,6 2012
90 3 • 42 25 6 rü 15 0,88 1610 190 3 ° 50 32 9 rü 4 4,9 2012
4 • 42 25 6 rü 27 1,1 1610 4 ° 60 45 9 rü 3,5 5,2 2517
5 • 42 25 6 rü 39 1,4 1610 5 ° 60 45 9 rü 9,5 6,3 2517
1 • 32 25 8 bü 0,8 1210 1 ° 50 32 8 bü 2,5 2012
2 • 42 25 6 rü 3 0,97 1610 2 ° 50 32 8 bü 3,1 2012
95 3 • 42 25 6 rü 15 1,1 1610 200 3 ° 50 32 9 rü 4 3,7 2012
4 • 42 25 6 rü 27 1,3 1610 4 ° 60 45 9 rü 3,5 5,4 2517
5 • 42 25 6 rü 39 1,6 1610 5 ° 60 45 9 rü 9,5 6,1 2517
1 • 32 25 8 bü 0,8 1210 1 X 50 32 8 bü 2,8 2012
2 • 42 25 6 rü 3 0,94 1610 2 X 50 32 8 bü 3,4 2012
100 3 • 42 25 6 rü 15 1,2 1610 224 3 ° 50 32 9 rü 4 4,2 2012
4 • 42 25 6 rü 27 1,4 1610 4 ° 60 45 9 rü 3,5 6,1 2517
5 • 50 32 6 rü 32 1,6 2012 5 ° 60 45 9 rü 9,5 7,0 2517
1 • 42 25 8 bü 0,9 1610 1 X 50 32 7 v8 3,3 2012
2 • 42 25 6 rü 3 1,1 1610 2 X 50 32 7 v2 3,9 2012
106 3 • 42 25 6 rü 15 1,4 1610 250 3 X 50 32 10 rü 4 4,8 2012
4 • 42 25 6 rü 27 1,6 1610 4 ° 60 45 9 rü 3,5 6,8 2517
5 • 50 32 6 rü 32 1,9 2012 5 ° 60 45 9 rü 9,5 7,4 2517
1 • 42 25 8 bü 1 1610 1 X 50 32 7 v8 3,8 2012
2 • 42 25 6 rü 3 1,3 1610 2 X 50 32 7 v2 4,9 2012
112 3 • 50 32 6 rü 8 1,4 2012 280 3 X 60 45 7 v 2,5 7,1 2517
4 • 50 32 6 rü 20 1,7 2012 4 X 60 45 10 rü 3,5 8,2 2517
5 • 50 32 6 rü 32 2,2 2012 5 X 60 45 10 rü 9,5 10,6 2517
1 • 42 25 8 bü 1,1 1610 1 X 50 32 7 v8 4,8 2012
2 • 42 25 6 rü 3 1,5 1610 2 X 50 32 7 v2 5,8 2012
118 3 • 50 32 6 rü 8 1,7 2012 315 3 X 60 45 7 v2,5 7,5 2517
4 • 50 32 6 rü 20 2 2012 4 X 60 45 10 rü 3,5 9,3 2517
5 • 50 32 6 rü 32 2,3 2012 5 X 60 45 10 rü 9,5 9,8 2517
1 • 42 25 8 bü 1,2 1610 2 X 50 32 7 v2 6,5 2012
2 • 42 25 6 rü 3 1,8 1610 3 X 60 45 7 v 2,5 8,9 2517
355
125 3 • 50 32 2 bü 2 2012 4 X 60 45 10 rü 3,5 9,5 2517
4 • 50 32 2 bü 2,3 2012 5 X 60 45 10 rü 9,5 13,0 2517
5 • 50 32 6 rü 32 2,7 2012 2 X 60 45 7 v 8,5 8,8 2517
1 • 42 25 8 bü 1,4 1610 400 3 X 60 45 7 v 2,5 10,5 2517
2 • 42 25 6 rü 3 2,1 1610 4 X 60 45 10 rü 3,5 11,5 2517
132 3 • 50 32 2 bü 2,3 2012
4 • 50 32 2 bü 2,7 2012
5 • 50 45 6 rü 19 3,2 2517

6
Efective.Ø Grooves •
SPA º
d2
max.
l Design Weight Bush No.

X
dw
mm mm kg
Efective.Ø Grooves • d2 l Design Weight Bush No. 1 ° 42 25 8 bü 2,1 1610
º max. 2 ° 50 32 9 rü 1,5 5,2 2012
X 180 3 • 60 45 6 rü 5 6,1 2517
dw
mm mm kg 4 • 60 45 2 bü 6,8 2517
1 • 28 22 8 bü 0,4 1108 5 • 75 51 4 rü 14,5 7 3020
67 1 ° 42 25 8 bü 2,7 1610
2 • 28 22 6 rü 13 0,5 1108
1 • 28 22 8 bü 0,4 1108 2 ° 50 32 9 rü 1,5 3,9 2012
71 190 3 • 60 45 6 rü 5 7,2 2517
2 • 28 22 6 rü 13 0,55 1108
1 • 28 22 8 bü 0,45 1108 4 • 60 45 2 bü 7,5 2517
75 5 • 75 51 2 bü 8,0 3020
2 • 28 22 6 rü 13 0,60 1108
1 • 32 25 8 bü 0,53 1210 1 ° 50 32 8 bü 2,8 2012
80 2 • 32 25 6 rü 10 0,74 1210 2 ° 60 45 5 v5 4,7 2517
3 • 32 25 6 rü 25 0,82 1210 200 3 ° 60 45 9 rü 2,5 5,5 2517
1 • 32 25 8 bü 0,60 1210 4 • 75 51 2 bü 8,5 3020
85 2 • 32 25 6 rü 10 0,81 1210 5 • 75 51 4 rü 14,5 9,4 3020
3 • 32 25 6 rü 25 0,9 1210 1 ° 50 32 8 bü 3,0 2012
1 • 32 25 8 bü 0,8 1210 2 ° 60 45 5 v5 5,0 2517
2 • 42 25 6 rü 10 0,9 1610 212 3 ° 60 45 9 rü 2,5 5,9 2517
90 4 • 75 51 2 bü 8,6 3020
3 • 42 25 6 rü 25 1 1610
4 • 42 38 6 rü 27 1,3 1615 5 • 75 51 2 bü 10,8 3020
1 • 32 25 8 bü 0,8 1210 1 ° 50 32 8 bü 3,2 2012
2 • 42 25 6 rü 10 0,9 1610 2 X 60 45 8 bü 5,3 2517
95 224 3 X 60 45 10 rü 2,5 6,2 2517
3 • 42 25 6 rü 25 1,3 1610
4 • 42 38 6 rü 27 1,7 1615 4 • 75 51 2 bü 11,5 3020
1 • 42 25 8 bü 0,9 1610 5 • 75 51 2 bü 12,5 3020
2 • 42 25 6 rü 10 1 1610 1 ° 50 32 8 bü 3,5 2012
100 3 • 42 25 2 bü 1,4 1610 2 X 60 45 8 bü 5,5 2517
4 • 42 38 2 bü 1,8 1615 236 3 X 60 45 10 rü 2,5 6,5 2517
5 • 42 38 2 bü 2,2 1615 4 ° 75 51 8 bü 8,5 3020
1 • 42 25 8 bü 0,9 1610 5 • 75 51 2 bü 10,8 3020
2 • 42 25 6 rü 10 1,2 1610 1 ° 50 32 5 v6 3,7 2012
106 3 • 42 25 2 bü 1,6 1610 2 X 60 45 7 v5 5,8 2517
4 • 50 32 6 rü 33 1,7 2012 250 3 X 60 45 10 rü 2,5 6,8 2517
5 • 50 32 6 rü 48 2,1 2012 4 ° 75 51 9 rü 7 9,5 3020
1 • 42 25 8 bü 1 1610 5 ° 75 51 9 rü 14,5 11 3020
2 • 42 25 6 rü 10 1,4 1610 1 ° 50 32 8 bü 4 2012
112 3 • 50 32 6 rü 18 1,6 2012 2 X 60 45 8 bü 6,5 2517
4 • 50 32 6 rü 33 2 2012 280 3 X 60 45 10 rü 2,5 76 2517
5 • 50 32 6 rü 48 2,4 2012 4 X 75 51 10 rü 7 10,5 3020
1 • 42 25 8 bü 1,1 1610 5 ° 90 89 5 v 4,5 17 3535
2 • 42 25 6 rü 10 1,6 1610 1 ° 50 32 8 bü 4,5 2012
118 3 • 50 32 2 bü 1,9 2012 2 X 60 45 8 bü 6,8 2517
4 • 50 32 2 bü 2,3 2012 300 3 X 60 51 8 bü 8,2 3020
5 • 50 32 2 bü 2,7 2012 4 X 75 51 10 rü 75 11,3 3020
1 • 42 25 8 bü 1,3 1610 5 ° 90 89 8 bü 19,0 3535
2 • 42 25 6 rü 10 1,9 1610 1 ° 50 32 8 bü 4,6 2012
125 3 • 50 32 2 bü 2,3 2012 2 X 60 45 8 bü 7 2517
4 • 50 32 2 bü 2,7 2012 315 3 X 75 51 7 v 0,5 11 3020
5 • 50 32 4 rü 24 3,2 2012 4 X 75 51 10 rü 7 12 3020
1 • 42 25 8 bü 1,5 1610 5 ° 90 89 5 v 4,5 18,5 3535
2 • 50 32 6 rü 3 2,2 2012 1 X 50 32 8 bü 5,6 2012
132 3 • 50 32 2 bü 2,6 2012 2 X 60 45 8 bü 8,9 2517
4 • 60 45 2 bü 2,8 2517 355 3 X 75 51 7 v 0,5 12 3020
5 • 60 45 4 rü 17,5 3,4 2517 4 X 75 51 10 rü 7 13 3020
1 • 42 25 8 bü 1,8 1610 5 X 90 89 7 v 4,5 20 3535
2 • 50 32 6 rü 3 2,6 2012 1 X 50 32 8 bü 6,5 2012
140 3 • 60 45 6 rü 5 2,9 2517 2 X 60 45 8 bü 10 2517
4 • 60 45 2 bü 3,6 2517 400 3 X 75 51 8 bü 13 3020
5 • 60 45 4 rü 17,5 4 2517 4 X 75 51 10 rü 7 14,5 3020
1 • 42 25 8 bü 1,9 1610 5 X 90 89 7 v 4,5 21,5 3535
2 • 50 32 6 rü 3 3,2 2012 2 X 60 45 8 bü 11,5 2517
150 3 • 60 45 6 rü 5 3,6 2517 3 X 75 51 8 bü 14,5 3020
450
4 • 60 45 2 bü 4,4 2517 4 X 75 51 10 rü 7 16,5 3020
5 • 60 45 4 rü 17,5 4,8 2517 5 X 90 89 7 v 4,5 23 3535
1 • 42 25 8 bü 2,2 1610 2 X 60 45 8 bü 12,5 2517
2 • 50 32 6 rü 3 3,2 2012 3 X 75 51 8 bü 15,5 3020
500
160 3 • 60 45 6 rü 5 3,8 2517 4 X 75 51 10 rü 7 18 3020
4 • 60 45 2 bü 4,4 2517 5 X 90 89 7 v 4,5 25 3535
5 • 60 45 4 rü 17,5 4,9 2517 3 X 75 51 8 bü 16 3020
1 • 42 25 8 bü 2,0 1610 560 4 X 90 89 7 v 12 23,5 3535
2 • 50 32 6 rü 3 4,0 2012 5 X 90 89 7 v 4,5 27,5 3535
170 3 • 60 45 6 rü 5 4,2 2517 3 X 75 51 8 bü 10 3020
4 • 60 45 2 bü 5,8 2517 630 4 X 90 89 7 v 12 28 3535
5 • 75 51 2 bü 5,9 3020 5 X 90 89 7 v 4,5 31 3535

7
SPB
Efective.Ø Grooves • d2 l Design Weight Bush No. Efective.Ø Grooves • d2 l Design Weight Bush No.
º max. º max.
X X
dw dw
mm mm kg mm mm kg
1 • 42 25 1 bü 0,9 1610 1 º 50 32 5 v 3,5 4,6 2012
100 2 • 42 25 6 rü 19 1,2 1610 2 º 60 45 8 bü 6,6 2517
3 • 42 25 6 rü 38 1,7 1610 3 º 60 45 2 bü 8,1 2517
1 • 42 25 1 bü 1,1 1610 4 • 75 51 4 rü 15,5 12,3 3020
224
112 2 • 42 25 6 rü 19 1,5 1610 5 • 75 51 4 rü 25 13,8 3020
3 • 42 25 6 rü 38 2 1610 6 • 90 89 4 rü 15,5 17,8 3535
1 • 42 25 1 bü 1,3 1610 8 • 90 89 4 rü 34,5 20 3535
118 2 • 42 25 2 bü 1,7 1610 10 • 90 89 4 rü 53,5 22 3535
3 • 42 25 2 bü 2,3 1610 1 º 50 32 5 v 3,5 5 2012
1 • 42 25 1 bü 1,5 1610 2 º 60 45 8 bü 7,2 2517
2 • 50 32 2 bü 2 2012 3 º 60 45 8 bü 8,8 2517
125 3 • 50 32 2 bü 2,7 2012 4 • 75 51 4 rü 15,5 14 3020
236
4 • 50 32 4 rü 25 3,3 2012 5 • 90 89 4 rü 6 19,5 3535
5 • 50 32 6 rü 69 3,7 2012 6 • 90 89 4 rü 15,5 21 3535
1 • 42 25 1 bü 1,8 1610 8 • 90 89 4 rü 34,5 23 3535
2 • 50 32 2 bü 2,4 2012 10 • 90 89 4 rü 53,5 25 3535
132 3 • 50 32 2 bü 3 2012 1 º 50 32 5 v 3,5 5,6 2012
4 • 50 32 4 rü 25 3,7 2012 2 º 60 45 8 bü 7,7 2517
5 • 60 45 6 rü 56 4,5 2517 3 º 75 51 8 bü 11 3020
1 • 42 25 1 bü 2 1610 4 º 75 51 9 rü 15,5 12,5 3020
250
2 • 50 32 2 bü 2,7 2012 5 • 90 89 4 rü 6 22,5 3535
3 • 50 32 2 bü 3,5 2012 6 • 90 89 4 rü 15,5 24,5 3535
140
4 • 60 45 4 rü 18,5 4 2517 8 • 90 89 4 rü 34,5 27 3535
5 • 60 45 4 rü 28 4,8 2517 10 • 90 89 4 rü 53,5 29 3535
6 • 60 45 4 rü 37,5 6,1 2517 1 X 50 32 7 v 3,5 8 2012
1 • 42 25 1 bü 2,5 1610 2 X 60 45 8 bü 9,5 2517
2 • 50 32 2 bü 3,3 2012 3 X 75 51 10 rü 6 13 3020
3 • 60 45 2 bü 4,1 2517 4 º 75 51 9 rü 15,5 15 3020
150 280
4 • 60 45 4 rü 18,5 4,9 2517 5 º 90 89 9 rü 6 21 3535
5 • 60 45 4 rü 28 5,7 2517 6 º 90 89 9 rü 15,5 22 3535
6 • 60 45 4 rü 37,5 6,5 2517 8 º 90 89 9 rü 34,5 25 3535
1 • 42 25 1 bü 2,8 1610 10 º 90 89 9 rü 53,5 30 3535
2 • 50 32 2 bü 3,9 2012 2 X 60 45 8 bü 10,4 2517
3 • 60 45 2 bü 4,8 2517 3 X 75 51 10 rü 6 13,5 3020
160
4 • 60 45 4 rü 18,5 5,7 2517 4 º 90 89 8 bü 19,0 3535
300
5 • 60 45 4 rü 28 6,6 2517 5 º 90 89 9 rü 6 22,0 3535
6 • 75 51 4 rü 34,5 6,5 3020 6 º 90 89 9 rü 15,5 23,6 3535
1 • 42 25 1 bü 3,3 1610 8 º 90 89 9 rü 34,5 31,5 3535
2 • 50 32 2 bü 4,5 2012 2 X 60 45 8 bü 11,5 2517
3 • 60 45 2 bü 5,7 2517 3 X 75 51 10 rü 6 15,5 3020
170
4 • 60 45 4 rü 18,5 6,7 2517 4 X 90 89 7 v 3,5 18 3535
5 • 75 51 4 rü 25 6,8 3020 315 5 º 90 89 9 rü 6 23,5 3535
6 • 75 51 4 rü 34,5 7,7 3020 6 º 90 89 9 rü 15,5 25,5 3535
1 ° 42 25 1 bü 3,7 1610 8 º 90 89 9 rü 34,5 29 3535
2 • 60 45 8 bü 5,5 2517 10 º 90 89 9 rü 53,5 33 3535
3 • 60 45 2 bü 6,6 2517 2 X 60 45 8 bü 12,5 2517
180 4 • 60 45 4 rü 18,5 7,7 2517 3 X 75 51 10 rü 6 16,5 3020
5 • 75 51 4 rü 25 7,9 3020 4 X 90 89 7 v 3,5 19,5 3535
335
6 • 75 51 4 rü 34,5 8,9 3020 5 º 90 89 9 rü 6 25,0 3535
8 • 75 76 4 rü 41 12 3030 6 º 90 89 9 rü 15,5 28,0 3535
1 ° 50 32 5 v 3,5 4,1 2012 8 º 90 89 9 rü 34,5 32,0 3535
2 • 60 45 8 bü 6,4 2517 2 X 75 51 7 v 3,5 15 3020
3 • 60 45 2 bü 7,6 2517 3 X 75 51 10 rü 6 17,5 3020
190 4 • 60 45 4 rü 18,5 8,7 2517 4 X 90 89 7 v 3,5 21 3535
5 • 75 51 4 rü 25 9,1 3020 355 5 º 90 89 9 rü 6 27 3535
6 • 75 51 4 rü 34,5 10,1 3020 6 º 90 89 9 rü 15,5 29 3535
8 • 75 76 4 rü 41 13 3030 8 º 90 89 9 rü 34,5 35 3535
1 ° 50 32 5 v 3,5 4,1 2012 10 º 100 102 9 rü 47 41 4040
2 • 60 45 8 bü 7,5 2517 2 X 75 51 7 v 3,5 9,5 3020
3 • 60 45 2 bü 8,6 2517 3 X 75 51 10 rü 6 11,5 3020
200 4 • 75 51 4 rü 15,5 9,3 3020 375 4 X 90 89 7 v 3,5 16,5 3535
5 • 75 51 4 rü 25 10,5 3020 6 X 90 89 10 rü 15,5 25,0 3535
6 • 75 51 4 rü 34,5 11,7 3020 8 ° 100 102 9 rü 28 40,0 4040
8 • 90 89 4 rü 34,5 15 3535 2 X 75 51 7 v 3,5 11,5 3020
1 ° 50 32 5 v 3,5 4,2 2012 3 X 90 89 7 v 13 17 3535
2 ° 60 45 8 bü 5,9 2517 4 X 90 89 7 v 3,5 22 3535
3 ° 60 45 2 bü 7,6 2517 400 5 X 90 89 10 rü 6 25,5 3535
212 4 • 75 51 4 rü 15,5 10,8 3020 6 X 90 89 10 rü 15,5 28,5 3535
5 • 75 51 4 rü 25 12,1 3020 8 X 100 102 10 rü 28 45 4040
6 • 90 89 4 rü 15,5 15,2 3535 10 X 100 102 10 rü 47 50 4040
8 • 90 89 4 rü 34,5 17,2 3535

8
SPB
Efective.Ø Grooves • d2 l Design Weight Bush No.
º max.
X
dw
mm mm kg
2 X 75 51 8 bü 12,5 3020
3 X 90 89 8 bü 18,0 3535
425 4 X 90 89 8 bü 23,5 3535
6 X 100 89 10 rü 15,5 31,0 3535
8 X 110 102 10 rü 28 52,5 4040
2 X 75 51 7 v 3,5 14 3020
3 X 90 89 8 bü 22 3535
4 X 90 89 8 bü 25,5 3535
450 5 X 90 89 8 bü 29 3535
6 X 100 102 8 bü 35 4040
8 X 100 102 10 rü 28 54 4040
10 X 110 114 10 rü 41 65 4545
2 X 75 51 7 v 3,5 15,5 3020
3 X 90 89 8 bü 24 3535
4 X 90 89 8 bü 28 3535
500 5 X 90 89 8 bü 32 3535
6 X 100 102 8 bü 38,5 4040
8 X 100 102 10 rü 28 55,5 4040
10 X 110 114 10 rü 41 67,5 4545
3 X 90 89 8 bü 27 3535
4 X 90 89 8 bü 31 3535
5 X 100 102 8 bü 39 4040
560
6 X 100 102 8 bü 43 4040
8 X 110 114 10 rü 22 69 4545
10 X 110 114 10 rü 41 74 4545
3 X 90 89 8 bü 31 3535
4 X 90 89 8 bü 36 3535
5 X 100 102 8 bü 44 4040
630
6 X 100 102 8 bü 51 4040
8 X 110 114 10 rü 22 77 4545
10 X 110 114 10 rü 41 83 4545
3 X 90 89 7 v 13 36 3535
4 X 90 89 7 v 3,5 41 3535
5 X 100 102 8 bü 51 4040
710
6 X 110 102 10 rü 9 59 4040
8 X 110 114 10 rü 22 86 4545
10 X 110 114 10 rü 41 97 4545
3 X 90 89 7 v 13 38 3535
4 X 100 102 7 v 10 48 4040
5 X 100 102 8 bü 56 4040
800
6 X 110 114 10 rü 3 66 4545
8 X 110 114 10 rü 22 100 4545
10 X 110 114 10 rü 41 110 4545
4 X 100 102 7 v 10 77 4040
5 X 110 102 8 bü 88 4040
900 6 X 110 114 10 rü 3 105 4545
8 X 110 114 10 rü 22 115 4545
10 X 125 127 10 rü 34,5 145 5050
4 X 100 102 7 v 10 96 4040
5 X 110 114 7 v 6,5 106 4545
1000 6 X 110 114 10 rü 3 110 4545
8 X 125 127 10 rü 15,5 150 5050
10 X 125 127 10 rü 34,5 167 5050

9
SPC SPC
Efective.Ø Grooves • d2 l Design Weight Bush No. Efective.Ø Grooves • d2 l Design Weight Bush No.
º max. º max.
X X
dw dw
mm mm kg mm mm kg
3 • 75 51 4 rü 17 12,3 3020 3 X 90 89 7 v2 34 3535
4 • 90 89 4 rü 11 16,3 3535 4 X 90 89 10 rü 11 39 3535
224 5 • 90 89 4 rü 23,5 18,4 3535 5 X 100 102 10 rü 17 49 4040
6 • 90 89 4 rü 36 20,4 3535 450 6 º 110 114 9 rü 24 67 4545
8 • 90 89 4 rü 62 24,5 3535 8 º 125 127 9 rü 43 81 5050
3 • 75 51 4 rü 17 13,9 3020 10 º 125 127 9 rü 68 92,5 5050
4 • 90 89 4 rü 11 19 3535 12 º 125 127 9 rü 50 113 5050
236 5 • 90 89 4 rü 23,5 21,1 3535 3 X 90 89 7 v2 40 3535
6 • 90 89 4 rü 36 23,1 3535 4 X 90 89 10 rü 11 42 3535
8 • 90 89 4 rü 62 27,8 3535 5 X 100 102 10 rü 17 51,5 4040
3 • 75 51 4 rü 17 13,1 3020 475 6 º 110 114 9 rü 24 72 4545
4 • 90 89 4 rü 11 22,4 3535 8 º 125 127 9 rü 43 86 5050
5 • 90 89 4 rü 23,5 24,5 3535 10 º 125 127 9 rü 50 90 5050
250
6 • 90 89 4 rü 36 26,7 3535 12 º 125 127 9 rü 50 120 5050
8 • 90 89 4 rü 62 31,1 3535 4 X 90 89 10 rü 11 44 3535
10 • 100 102 4 rü 81 36,4 4040 5 X 100 102 10 rü 17 53,5 4040
3 • 90 89 8 bü 23,7 3535 6 X 110 114 10 rü 24 66,5 4545
4 • 90 89 4 rü 11 26,2 3535 500
8 º 125 127 9 rü 43 91 5050
265 5 • 90 89 4 rü 23,5 28,5 3535 10 º 125 127 9 rü 68 105 5050
6 • 90 89 4 rü 36 31,3 3535 12 º 125 127 9 rü 50 127 5050
8 • 90 89 4 rü 62 36,2 3535 4 X 100 102 10 rü 4 60 4040
3 º 90 89 8 bü 20,1 3535 5 X 110 114 10 rü 11 71 4545
4 º 90 89 9 rü 11 22,7 3535 6 X 125 127 10 rü 17 85,5 5050
5 º 90 89 9 rü 23,5 23,9 3535 560
280 8 X 125 127 10 rü 43 101,5 5050
6 º 90 89 9 rü 36 26,4 3535 10 X 125 127 10 rü 68 114 5050
8 º 90 89 9 rü 62 41 3535 12 X 125 127 10 rü 50 145 5050
10 • 100 102 4 rü 81 47,5 4040 5 X 125 127 10 rü 4,5 91 5050
3 º 90 89 5 v2 21,4 3535
6 X 125 127 10 rü 17 97,5 5050
4 º 90 89 9 rü 11 24,4 3535
630 8 X 125 127 10 rü 43 116 5050
5 º 90 89 9 rü 23,5 27,3 3535
300 10 X 125 127 10 rü 68 127 5050
6 º 90 89 9 rü 36 30 3535
12 X 125 127 10 rü 50 160 5050
8 • 100 102 4 rü 55 48,5 4040
5 X 125 127 10 rü 4,5 95 5050
10 • 110 114 4 rü 75 55 4545
6 X 125 127 10 rü 17 108 5050
3 º 90 89 5 v2 23 3535
4 º 90 89 9 rü 11 26 3535
710 8 X 125 127 10 rü 43 127 5050
5 º 90 89 9 rü 23,5 27 3535 10 X 125 127 10 rü 68 147 5050
315 12 X 125 127 10 rü 50 170 5050
6 º 90 89 9 rü 36 32 3535
8 • 100 102 4 rü 55 54 4040 5 X 125 127 10 rü 4,5 115 5050
10 • 110 114 4 rü 75 62 4545 6 X 125 127 10 rü 17 125 5050
12 • 125 127 4 rü 50 69 5050 800 8 X 125 127 10 rü 43 140 5050
3 X 90 89 7 v2 25 3535 10 X 125 127 10 rü 68 164 5050
4 X 90 89 10 rü 11 28 3535 12 X 125 127 10 rü 50 220 5050
335 5 º 90 89 9 rü 23,5 31,5 3535 5 X 125 127 10 rü 4,5 154 5050
6 º 90 89 9 rü 36 35 3535 6 X 125 127 10 rü 17 160 5050
8 º 100 102 9 rü 55 46,5 4040 1000 8 X 125 127 10 rü 43 197 5050
10 • 110 114 4 rü 50 77 4545 10 X 125 127 10 rü 68 245 5050
12 • 125 127 4 rü 50 82 5050 12 X 125 127 10 rü 50 270 5050
3 X 90 89 7 v2 28 3535 5 X 125 127 10 rü 4,5 178 5050
4 X 90 89 10 rü 11 31 3535 6 X 125 127 10 rü 17 193 5050
5 X 90 89 10 rü 23,5 34 3535 1250 8 X 125 127 10 rü 43 237 5050
355 37,5 10 X 125 127 10 rü 68 294 5050
6 º 90 89 9 rü 36 3535
8 º 100 102 9 rü 55 49,5 4040 12 X 125 127 10 rü 50 310 5050
10 • 110 114 4 rü 75 84 4545
12 • 125 127 4 rü 50 86 5050
3 X 90 89 7 v2 30 3535
4 X 90 89 10 rü 11 33,5 3535
375 5 X 90 89 10 rü 23,5 37 3535
6 º 100 102 9 rü 30 45,5 4040
8 º 110 114 9 rü 49 59 4545
10 • 110 114 4 rü 50 88 4545
12 • 125 127 4 rü 50 92 5050
3 X 90 89 7 v2 33 3535
4 X 90 89 10 rü 11 35,5 3535
5 X 90 89 10 rü 23,5 40,5 3535
400
6 º 100 102 9 rü 30 49 4040
8 º 110 114 9 rü 49 63 4545
10 º 125 127 9 rü 68 80 5050
12 º 125 127 9 rü 50 98 5050
3 X 90 89 7 v2 37 3535
4 X 90 89 10 rü 11 42 3535
425 5 X 90 89 10 rü 23,5 46,2 3535
6 º 100 102 9 rü 30 56 4040
8 º 110 114 9 rü 49 69 4545
10 º 125 127 9 rü 50 96 5050
12 º 125 127 9 rü 50 100 5050

10
Weld-on Hub
Taper welded nubs are made of steel, drilled, countersunk and given a taper hole to enable
them to be mounted with standard taper bushes. The protruding flange provides a con-
venient possibility of welding hubs in fans, fanwheels, steel disks, chain wheel pulleys and
many other devices which have to be mounted permanently on a shaft. Welded hubs are
simple to install and are ideally suitable where heavy-duty conditions are encountered.
When the bolts are tightened, the hole is pressed together, thus fastening it on the shaft
in the form of a press fit. The type of design eliminates all mounting difficulties, as well as
preventing any loosening and migration on the hub during operation.

Type WM
Hub size Bush No. A B C D E F F1 X
mm mm mm mm mm mm mm mm
WM 12 1210 70 60 58 25 9 10 8 9
WM 16-1 1610 83 70 68 25 9 10 8 9
WM 16-2 1615 83 70 68 38 16 11 8 16
WM 20 2012 95 90 88 32 12 12 10 12
WM 25 2517 127 110 108 45 19 13 10 19
WM 30-2 3020 152 130 125 51 20 15 12 20
WM 30-3 3030 152 130 125 76 25 19 12 25
WM 35 3535 184 155 151 89 32 25 15 32
WM 40 4040 225 195 187 102 32 32 15 32
WM 45 4545 254 220 213 114 38 38 20 38
WM 50 5050 276 242 228 127 38 38 20 38

Type WH
Hub size Bush No. A B C D E F F1 X
mm mm mm mm mm mm mm mm
WH 12 1210 70 65 64,5 25 9 10 - -
WH 16 1610 83 75 74,5 25 9 10 - -
WH 20 2012 95 90 89,5 32 12 12 - -
WH 25 2517 115 110 109,5 45 19 15 - -
WH 30 3020 145 140 139,5 51 20 15 21 14
WH 35 3525 190 180 179,5 65 25 25 31 19
WH40 4040 200 190 189,5 102 32 30 27 22
WH45 4545 210 200 199,5 114 40 30 33 25
WH 50 5050 230 220 219,5 127 40 35 37 20

11
Bolt-on Hubs
Taper screw-on hubs have been designed for use with
taper bushes. They offer the favourable facility of
mounting fans, fanwheels and other devices firmly on
a shaft. DESCH screw-on hubs are made of grey cast
iron or steel and are phosphatised to provide additional
corrosion-proofing.

Type SM
A B C D E J
Hub size Bush No.
mm mm mm mm mm mm
SM 12 1210 180 90 135 25 6,5 6 x 7,5
SM 16-1 1610 200 110 150 25 7,5 6 x 7,5
SM 16-2 1615 200 110 150 38 7,5 6 x 7,5
SM 20 2012 270 140 190 32 8,5 6 x 9,5
SM 25 2517 340 170 240 45 9,5 8 x 11,5
SM 30-1 3020 430 220 300 51 13,5 8 x 13,5
SM 30-2 3020 485 250 340 51 13,5 8 x 13,5

12
Type BF

A B C D E G H J
Hub size Bush No.
mm mm mm mm mm mm mm mm
BF 12 1210 120 80 100 25 5,5 75 10 6 x 7,5
BF 16 1610 130 90 110 25 6,5 85 10 6 x 7,5
BF 20 2012 145 100 125 32 8,5 95 13 6 x 9,5
BF 25 2517 185 130 155 45 11,5 119 20 8 x 11,5
BF 30 3020 200 165 190 51 11,5 147 20 8 x 13,5

off steel
Weight A B C D1 D2 D3 D4 D5 E F G
Welded Hub
Hub Size Bush No.
kg mm mm mm mm mm mm mm mm mm mm mm
SM 12S 1210 WM 12 2,0 9 25 5 180 60 90 70 58 9 12 14
SM 16-1S 1610 WM16-1 2,4 9 25 5 200 70 110 83 68 9 12 14
SM 16-2S 1615 WM 16-2 2,5 10 38 15 200 70 110 83 68 10 13 25
SM 20S 2517 WM 25 6,0 19 45 11 270 110 140 127 108 11 14 22
SM 25S 2517 WM 25 9,2 19 45 10 340 110 170 127 108 12 15 22
SM 30-1S 3030 WM 30-3 20,0 25 76 32 430 130 220 152 125 15 19 47
SM 30-2S 3030 WM 30-3 25,0 25 76 31 485 130 250 152 125 15 20 46

13
Data sheet
for calculating / checking the drives

Inquiry No. dated


Company
Road

Requirements pieces/ order

Ofer No. dated

DESCH DPC GmbH & Co. KG


Postbox 14 40
59753 Arnsberg / Germany
Processed by:

Engine: Driven machine:


type type

size of start-up moment start-up: under load idling

type of start-up Art der Belastung: constant pulsating

daily operating time hours intermittent

number of switching operations hourly daily Power: P normal kW

power: P normal kW P maximal kW

P maximal kW or max. torque Nm with n1 min-1

or max. torque Nm bei n1 rpm rotary freuency n2 rpm

rotary frequenzy n1 rpm n2min rpm

efective or outside diameter of pulley: n2max rpm

dd1 mm da1 mm efective or outside diameter of pulley

dd1 min mm da1 min mm dd1 mm da1 mm

dd1 max mm da1 max mm dd1 min mm da1 min mm

pulley with b2 max mm dd1 max mm da1 max mm

pulley width b2 max mm

General data
transmission ratio i i min i max

axle base a mm amin mm amax mm

operating conditions:

ambient temperature °C minimal

ambient temperature °C maximal

inluence of oil

water

acid

dust

14
DESCH DPC - Belt-Drives / Transmission Components
Special pulleys Timing belt pulleys

V-Belts timing belts Motor slides made


of cast iron
EN-GJL-200

Motor slides made of steel Motor mounts

DESCH DPC - Bearings


Flange bearings Cap bearings
acc. to DIN 502 with bronze shell
with or without bronze bush acc. to DIN 505 L

Flange bearings Cap bearings


acc. to DIN 503 with bronze shell
with or without bronze bush acc. to DIN 506

Eye bearings
acc. to DIN 504
with or without bronze bush

Catalogues on request!

15
© 2012 DESCH DPC GmbH & Co. KG · KS 12 – GB

DESCH Antriebstechnik GmbH & Co. KG


Postbox 14 40 | 59753 Arnsberg/Germany
Kleinbahnstraße 21 | 59759 Arnsberg/Germany
T +49 2932 300 268 | F +49 2932 300 442 68I
www.desch.de | E [email protected]

DESCH DPC GmbH & Co. KG DESCH Canada Ltd. DESCH Italia DESCH China
Postbox 14 40 240 Shearson Crescent Drive Technology Machinery (Shanghai) Ltd.
59753 Arnsberg/Germany Cambridge, Ontario Ufficio di rappresentanza in Italia No.10 Building, No.2317
Kleinbahnstraße 21 Canada N 1T 1J6 Via Cavriana, 3 Shengang Road, Songjiang District
59759 Arnsberg/Germany T +1800 2631866 20134 Milano/Italy 201612 Shanghai/China
Technical changes reser ved

T +49 2932 300 0 +1519 6214560 T +3902 7391280 T +86 21 5771 8058
F +49 2932 300 830 F +1519 6231169 F +3902 7391281 F +86 21 5765 5155
I www.desch.de I www.desch.de I www.desch.de I www.desch.de
E [email protected] E [email protected] E [email protected] E [email protected]

Powered by TCPDF (www.tcpdf.org)

You might also like