Catalog Phot Chan Dau SKF PDF

Industrial shaft seals
Pht chn du, Pht trc SKF of 488.
SI conversion table
Quantity Unit Conversion
Length inch 1 mm 0.039 in. 1 in. 25,40 mm

foot 1m 3.281 ft. 1 ft. 0,3048 m
yard 1m 1.094 yd. 1 yd. 0,9144 m
mile 1 km 0.6214 mile 1 mile 1,609 km
Velocity, foot per second 1 m/s 3.28 ft/s 1 ft/s 0,30480 m/s
speed foot per minute 1 m/s 196.8504 ft/min 1 ft/min 0,00508 m/s
mile per hour 1 km/h 0.6214 mile/h 1 mile/h 1,609 km/h
(mph) (mph)
Force pound-force 1N 0.225 lbf. 1 lbf. 4,4482 N
Pressure, pounds per 1 MPa 145 psi 1 psi 6,8948 ¥ 103 Pa

stress square inch
Temperature ° (degree) Celsius tC = 0,555 (tF – 32) Fahrenheit tF = 1,8 tC + 32
® SKF, DURATEMP, SPEEDI-SLEEVE and WAVE are registered

trademarks of the SKF Group.
© SKF Group 2013
The contents of this publication are the copyright of the publisher
and may not be reproduced (even extracts) unless prior written per-
mission is granted. Every care has been taken to ensure the accuracy
of the information contained in this publication but no liability can be
accepted for any loss or damage whether direct, indirect or conse-
quential arising out of the use of the information contained herein.
The data in this publication may differ from that provided in earlier
publications because of redesign, technological developments or
revised methods of calculation. SKF reserves the right to make
continuing improvements to SKF products without prior notice
with respect to materials, design and manufacturing methods,
as well as changes necessitated by technological developments.
PUB SE/P1 10919/2 EN · June 2013
This publication supersedes publication 5300.
www.nguyenxuong.com
1 Product data – general. . . . . . . . . . . . . . . . . . . . . . . . . 11 1
2 Radial shaft seals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 2
3 Cassette seals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 321 3
4 Wear sleeves. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 327 4
5 Track pin seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 373 5
6 Metal face seals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 379 6
7 V-ring seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 389 7
8 Axial clamp seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 471 8
9 Product index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 482 9
www.nguyenxuong.com 1
This is SKF
From one simple but inspired solution to a mis-

alignment problem in a textile mill in Sweden,
and fifteen employees in 1907, SKF has grown
to become a global industrial knowledge leader.
Over the years we have built on our expertise in
bearings, extending it to seals, mechatronics,
services and lubrication systems. Our know-
ledge network includes 46 000 employees,
15 000 distributor partners, offices in more
than 130 countries, and a growing number of
SKF Solution Factory sites around the world.
Research and development
We have hands-on experience in over forty
industries, based on our employees’ knowledge
of real life conditions. In addition our world-
leading experts and university partners who
pioneer advanced theoretical research and
development in areas including tribology, condi-
tion monitoring, asset management and bearing
life theory. Our ongoing commitment to research
and development helps us keep our customers
at the forefront of their industries.
SKF Solution Factory

makes SKF knowledge
and manufacturing
expertise available
locally, to provide unique
solutions and services to
our customers.
2 www.nguyenxuong.com
Meeting the toughest challenges

Our network of knowledge and experience
along with our understanding of how our core
technologies can be combined helps us create
innovative solutions that meet the toughest of
challenges. We work closely with our customers
throughout the asset life cycle, helping them to
profitably and responsibly grow their businesses.
Working for a sustainable future
Since 2005, SKF has worked to reduce the
negative environmental impact from our own
operations and those of our suppliers. Our con-
tinuing technology development introduced
the SKF BeyondZero portfolio of products and
services which improve efficiency and reduce
energy losses, as well as enable new technol-
ogies harnessing wind, solar and ocean power.
This combined approach helps reduce the
environmental impact both in our own oper-
ations and in our customers’.
Working with SKF IT and

logistics systems and
application experts, SKF
Authorized Distributors
deliver a valuable mix of
product and application
knowledge to customers
worldwide.
SKF – the knowledge

engineering company
Our knowledge Design and develop

– your success at
ion
Man
ufa
ctu
SKF Life Cycle Management is how ic re
cif
an
d
Spe
we combine our technology plat

forms and advanced services, and
te
st
apply them at each stage of the SKF Life Cycle
asset life cycle, to help our cus Management
ission
tomers to be more successful,
Ma
ain
in
sustainable and profitable.

t
mm
an
dr
ep
co
air
an
d
all
Opera Inst
te and monitor
Working closely with you entire application. This approach doesn’t just
Our objective is to help our customers improve focus on individual components like bearings or
productivity, minimize maintenance, achieve seals. It looks at the whole application to see
higher energy and resource efficiency, and opti- how each component interacts with the next.
mize designs for long service life and reliability.
Design optimization and verification
Innovative solutions SKF can work with you to optimize current or
Whether the application is linear or rotary or a new designs with proprietary 3-D modeling
combination of the two, SKF engineers can work software that can also be used as a virtual test
with you at each stage of the asset life cycle to rig to confirm the integrity of the design.
improve machine performance by looking at the
Bearings
SKF is the world leader in the design, development
and manufacture of high performance rolling bearings,
plain bearings, bearing units and housings.
Machinery maintenance
Condition monitoring technologies and maintenance
services from SKF can help minimize unplanned down-
time, improve operational efficiency and reduce main-
tenance costs.
Sealing solutions
SKF offers standard seals and custom engineered seal-
ing solutions to increase uptime, improve machine reli-
ability, reduce friction and power losses, and extend
lubricant life.
Mechatronics
SKF fly-by-wire systems for aircraft and drive-by-wire
systems for off-road, agricultural and forklift applica-
tions replace heavy, grease or oil consuming mechanical
and hydraulic systems.
Lubrication solutions
From specialized lubricants to state-of-the-art
lubrication systems and lubrication management
services, lubrication solutions from SKF can help to
reduce lubrication related downtime and lubricant
consumption.
Actuation and motion control

With a wide assortment of products – from actuators
and ball screws to profile rail guides – SKF can work
with you to solve your most pressing linear system
challenges.
Contents
This is SKF . . . . . . . . . . . . . . . . . . . . . . . . . . 2
SKF – the knowledge engineering

company . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Foreword . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
SKF industrial shaft seals
and accessories. . . . . . . . . . . . . . . . . . . . . 10
1 Product data – general. . . . . . . . . . . . . . 11
Industrial shaft seals. . . . . . . . . . . . . . . . 12

Profile overview selection. . . . . . . . . . . . . 13
Radial shaft seals. . . . . . . . . . . . . . . . . . 13
Wear sleeves. . . . . . . . . . . . . . . . . . . . . 15
Axial shaft seals. . . . . . . . . . . . . . . . . . . 16
Selection of seal design and material . . . . 17
Grease retention . . . . . . . . . . . . . . . . . . 17
Oil retention. . . . . . . . . . . . . . . . . . . . . . 18
Contaminant exclusion . . . . . . . . . . . . . 19
Retention and exclusion. . . . . . . . . . . . . 20
Separating two liquids. . . . . . . . . . . . . . 21
Circumferential
and rotational speed . . . . . . . . . . . . . . . 22
Pressure differentials. . . . . . . . . . . . . . . 23
Limited space. . . . . . . . . . . . . . . . . . . . . 24
Installation restrictions . . . . . . . . . . . . . 25
Arrangement. . . . . . . . . . . . . . . . . . . . . 26
Counterface design . . . . . . . . . . . . . . . . 27
Axial movement. . . . . . . . . . . . . . . . . . . 28
Seal materials. . . . . . . . . . . . . . . . . . . . . . 29
Cases and inserts. . . . . . . . . . . . . . . . . . 29
Garter springs. . . . . . . . . . . . . . . . . . . . 29
SKF Bore Tite Coating . . . . . . . . . . . . . . 29
Adhesives and bonding agents . . . . . . . 29
Sealing lip materials . . . . . . . . . . . . . . . 30
Wear resistance. . . . . . . . . . . . . . . . . . . . . 33
Operating temperatures . . . . . . . . . . . . . . 34
Chemical resistance. . . . . . . . . . . . . . . . . . 35
Storage and handling of seals. . . . . . . . . . 44
General . . . . . . . . . . . . . . . . . . . . . . . . . 44
Storage . . . . . . . . . . . . . . . . . . . . . . . . . 44
Cleaning and maintenance . . . . . . . . . . 45
2 Radial shaft seals. . . . . . . . . . . . . . . . . . . 47 Seals for general industrial

General . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 applications. . . . . . . . . . . . . . . . . . . . . . . . 92
Outside diameter design. . . . . . . . . . . . . . 54 HMS5 and HMSA10 seals. . . . . . . . . . . 92
SKF Bore Tite Coating . . . . . . . . . . . . . . 54 CRW1, CRWA1, CRWH1
Garter springs. . . . . . . . . . . . . . . . . . . . . . 55 and CRWHA1 seals . . . . . . . . . . . . . . . . 104
Dimensions. . . . . . . . . . . . . . . . . . . . . . . . 55 CRW5 and CRWA5 seals . . . . . . . . . . . . 160
Tolerances. . . . . . . . . . . . . . . . . . . . . . . 55 HDW1 seals. . . . . . . . . . . . . . . . . . . . . . 164
Sealing lip design. . . . . . . . . . . . . . . . . . . . 57 CRS1, CRSH1, CRSA1
Auxiliary lips. . . . . . . . . . . . . . . . . . . . . . . . 58 and CRSHA1 seals. . . . . . . . . . . . . . . . . 168
Coaxiality and runout. . . . . . . . . . . . . . . . . 59 PTFE radial shaft seals . . . . . . . . . . . . . 174
Coaxiality. . . . . . . . . . . . . . . . . . . . . . . . 59 HM and TL seals for grease
Runout. . . . . . . . . . . . . . . . . . . . . . . . . . 61 lubricated applications. . . . . . . . . . . . . . 178
Axial movement. . . . . . . . . . . . . . . . . . . . . 63 X seals, sealing against
Permissible speeds . . . . . . . . . . . . . . . . . . 63 housing bore. . . . . . . . . . . . . . . . . . . . . 192
Lubrication. . . . . . . . . . . . . . . . . . . . . . . . 65 Seals for heavy industrial
Lubrication of paired arrangements . . . 65 applications. . . . . . . . . . . . . . . . . . . . . . . . 202
Friction. . . . . . . . . . . . . . . . . . . . . . . . . . . . 66 General . . . . . . . . . . . . . . . . . . . . . . . . . 202
Chemical and thermal resistance. . . . . . . . 67 Metal-cased seals. . . . . . . . . . . . . . . . . 202
Seals under pressure. . . . . . . . . . . . . . . . . 69 Rubber outside diameter seals . . . . . . . 207
Shaft requirements. . . . . . . . . . . . . . . . . . 70 Additional design features. . . . . . . . . . . 211
General . . . . . . . . . . . . . . . . . . . . . . . . . 70 Size options of metal-cased HDS seals
Tolerances. . . . . . . . . . . . . . . . . . . . . . . 70 and all-rubber HS seals. . . . . . . . . . . . . 215
Surface roughness. . . . . . . . . . . . . . . . . 70 Product tables. . . . . . . . . . . . . . . . . . . . 217
Surface finish. . . . . . . . . . . . . . . . . . . . . 72
Hardness and surface treatment. . . . . . 72 3 Cassette seals . . . . . . . . . . . . . . . . . . . . . 321
Lead-in chamfers . . . . . . . . . . . . . . . . . 72 General . . . . . . . . . . . . . . . . . . . . . . . . . . . 322
Housing bore requirements. . . . . . . . . . . . 74 Design features. . . . . . . . . . . . . . . . . . . . . 323
General . . . . . . . . . . . . . . . . . . . . . . . . . 74 Testing. . . . . . . . . . . . . . . . . . . . . . . . . . . . 323
Metal-reinforced seals. . . . . . . . . . . . . . 74 Installation. . . . . . . . . . . . . . . . . . . . . . . . . 323
Seals without metal-reinforcement. . . . 74 SKF Mudblock seal designs
Tolerances. . . . . . . . . . . . . . . . . . . . . . . 76 MUD5 and MUD7. . . . . . . . . . . . . . . . . . . . 324
Surface roughness. . . . . . . . . . . . . . . . . 76
Seal installation, general industrial 4 Wear sleeves . . . . . . . . . . . . . . . . . . . . . . 327
applications. . . . . . . . . . . . . . . . . . . . . . . . 77 General . . . . . . . . . . . . . . . . . . . . . . . . . . . 328
General . . . . . . . . . . . . . . . . . . . . . . . . . 77 SKF Speedi-Sleeve . . . . . . . . . . . . . . . . . . 329
Seal installation, heavy industrial Features. . . . . . . . . . . . . . . . . . . . . . . . . 329
applications. . . . . . . . . . . . . . . . . . . . . . . . 79 Size range . . . . . . . . . . . . . . . . . . . . . . . 329
Metal-reinforced seals. . . . . . . . . . . . . . 79 SKF Speedi-Sleeve Gold . . . . . . . . . . . . 330
Seals without metal reinforcement. . . . 80 Test results. . . . . . . . . . . . . . . . . . . . . . . 330
Split seals. . . . . . . . . . . . . . . . . . . . . . . . 80 Selecting the right size. . . . . . . . . . . . . . 330
Cover plates. . . . . . . . . . . . . . . . . . . . . . 82 Installing SKF Speedi-Sleeve. . . . . . . . . 331
Multiple HS seal installations. . . . . . . . . 83 Removing SKF Speedi-Sleeve. . . . . . . . 333
Multiple HDS seal installations . . . . . . . 84 Product tables. . . . . . . . . . . . . . . . . . . . 334
PTFE seals. . . . . . . . . . . . . . . . . . . . . . . 85 Wear sleeves for heavy
Protecting the counterface surface industrial applications (LDSLV). . . . . . . . . 356
against corrosion. . . . . . . . . . . . . . . . . . . . 87 General . . . . . . . . . . . . . . . . . . . . . . . . . 356
Removal. . . . . . . . . . . . . . . . . . . . . . . . . . . 87 Designs and features. . . . . . . . . . . . . . . 357
Replacement. . . . . . . . . . . . . . . . . . . . . . . 87 Using LDSLV designs. . . . . . . . . . . . . . . 358
Designation system. . . . . . . . . . . . . . . . . . 88 Installation. . . . . . . . . . . . . . . . . . . . . . . 358
Metric radial shaft seals. . . . . . . . . . . . . 88 Removal. . . . . . . . . . . . . . . . . . . . . . . . . 358
Inch-size radial shaft seals. . . . . . . . . . 88 Product tables. . . . . . . . . . . . . . . . . . . . 360
Assortment and availability. . . . . . . . . . . . 88
5 Track pin seals. . . . . . . . . . . . . . . . . . . . . 373

General . . . . . . . . . . . . . . . . . . . . . . . . . . . 374
Features and benefits . . . . . . . . . . . . . . . . 374
Product tables. . . . . . . . . . . . . . . . . . . . . . 376
6 Metal face seals. . . . . . . . . . . . . . . . . . . . 379

General . . . . . . . . . . . . . . . . . . . . . . . . . . . 380
Design features. . . . . . . . . . . . . . . . . . . . . 380
Lubricant requirements. . . . . . . . . . . . . . . 381
Permissible operating conditions. . . . . . . . 382
Contaminants . . . . . . . . . . . . . . . . . . . . . . 382
Installing HDDF seals. . . . . . . . . . . . . . . . . 382
General . . . . . . . . . . . . . . . . . . . . . . . . . 382
Housing and seal preparation. . . . . . . . 382
Installation procedure. . . . . . . . . . . . . . 383
Product tables. . . . . . . . . . . . . . . . . . . . 384
7 V-ring seals . . . . . . . . . . . . . . . . . . . . . . . 389

General . . . . . . . . . . . . . . . . . . . . . . . . . . . 390
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . 390
Materials. . . . . . . . . . . . . . . . . . . . . . . . . . 391
Standard designs. . . . . . . . . . . . . . . . . . . . 392
Main V-ring functions . . . . . . . . . . . . . . . . 393
Other V-ring functions. . . . . . . . . . . . . . . . 394
Sliding velocities . . . . . . . . . . . . . . . . . . . . 395
Coaxiality and runout. . . . . . . . . . . . . . . . . 396
Misalignment. . . . . . . . . . . . . . . . . . . . . . . 396
Counterface. . . . . . . . . . . . . . . . . . . . . . . . 397
Counterface treatment . . . . . . . . . . . . . 397
Additional counterface information. . . . 397
Product table sorting order. . . . . . . . . . . . 398
Shaft requirements. . . . . . . . . . . . . . . . . . 399
Installing V-rings. . . . . . . . . . . . . . . . . . . . 399
Product tables. . . . . . . . . . . . . . . . . . . . . . 400
MVR axial shaft seals. . . . . . . . . . . . . . . . . 464
General . . . . . . . . . . . . . . . . . . . . . . . . . 464
Advantages and user benefits. . . . . . . . 464
Design and material. . . . . . . . . . . . . . . . 464
Temperature range . . . . . . . . . . . . . . . . 464
Sizes . . . . . . . . . . . . . . . . . . . . . . . . . . . 464
Installation. . . . . . . . . . . . . . . . . . . . . . . 465
Product tables. . . . . . . . . . . . . . . . . . . . 466
8 Axial clamp seals. . . . . . . . . . . . . . . . . . . 471

General . . . . . . . . . . . . . . . . . . . . . . . . . . . 472
Designs . . . . . . . . . . . . . . . . . . . . . . . . . . . 472
Design of the sealing arrangement. . . . . . 473
Installation instructions. . . . . . . . . . . . . . . 474
Product tables. . . . . . . . . . . . . . . . . . . . . . 476
9 Product index. . . . . . . . . . . . . . . . . . . . . . 482
Foreword
This edition of the Industrial shaft seals catalogue The SKF Interactive Engineering Catalogue
supersedes the one published in 2006 (publi SKF provides this catalogue in electronic format,
cation number 5300). For this new edition, the SKF Interactive Engineering Catalogue,
numerous revisions, additions and enhancements online at www.skf.com.
have been made to provide an even more com-
prehensive guide. Though the aim of this cata- Units
logue is to cover a very wide seal assortment, it The units in this catalogue are in accordance with
still only includes a selection of our complete ISO (International Organization for Standard
assortment of shaft seals and accessories. ization) standard 1000:1992, and SI (Système
The data in this catalogue may differ from International d’Unités).
that provided in earlier catalogues because of
redesign, technological developments or revised
methods of calculation. SKF reserves the right
to make continuing improvements to SKF prod-
ucts without prior notice with respect to materi-
als, design and manufacturing methods, as well
as changes necessitated by technological
developments.
Catalogue overview
In order to emphasize the importance of studying
the operating conditions of each application be-
fore selecting a sealing solution, this catalogue
outlines the most important factors to consider.
These are provided in the chapter Product data
– general, along with basic shaft and housing
bore requirements.
SKF industrial shaft seals and accessories
are divided into three main groups: radial shaft
seals, axial shaft seals and wear sleeves. Differ-
ent seal types within these groups are described
with their respective design, materials and
applications.
Product descriptions are followed by product
tables. It should be noted, however, that these
tables only cover a selection of available sizes.
Always contact your SKF sales representative for
complete and updated availability information.
SKF industrial shaft seals and accessories
Radial shaft seals Axial shaft seals Wear sleeves
Seals for general Track pin seals SKF Speedi-Sleeve

industrial applications
Seals for heavy Metal face seals Wear sleeves for heavy
industrial applications industrial applications
Cassette seals V-ring seals
Axial clamp seals
Product data – general 1
Industrial shaft seals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Profile overview selection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Radial shaft seals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Wear sleeves. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Axial shaft seals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Selection of seal design and material. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Grease retention. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Oil retention. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Contaminant exclusion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Retention and exclusion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Separating two liquids. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Circumferential and rotational speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Pressure differentials. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Limited space. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Installation restrictions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Arrangement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Counterface design. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Axial movement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Seal materials. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Cases and inserts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Garter springs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
SKF Bore Tite Coating. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Adhesives and bonding agents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Sealing lip materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Wear resistance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Operating temperatures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Chemical resistance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Storage and handling of seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Cleaning and maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Industrial shaft seals
Industrial shaft seals are used to seal the opening Availability

between a rotating and a stationary component, The SKF assortment of industrial shaft seals
or between two components in relative motion. comprises hundreds of different designs and
Primary seal functions include: material combinations. The products shown in
this catalogue and listed in the product tables
• Retain the lubricant are the more commonly used seal types and
• Exclude contaminants sizes.
• Separate two different media
• Seal under pressure Guidance values
Since several factors simultaneously affect the
To be effective, industrial shaft seals should sealing system and seal performance, all stated
operate with a minimum of friction and wear, values in graphs and tables in this publication
even under unfavourable operating conditions. should be considered as guidelines only and not
In order to meet the requirements of a variety of as absolute values for practical applications.
different applications and operating conditions,
SKF industrial shaft seals for rotating machine
components are manufactured from many dif-
ferent designs, materials and executions. Each
of these designs and material combinations has
specific properties, making them suitable for a
particular application. The main groups of shaft
seals and accessories are:
Radial shaft seals

• Seals for general industrial applications
• Seals for heavy industrial applications
• Cassette seals
Axial shaft seals

• Track pin seals
• Metal face seals
• V-ring seals
• Axial clamp seals
Wear sleeves
• SKF Speedi-Sleeve
• Wear sleeves for heavy industrial applications
Profile overview selection

Radial shaft seals 1
Seals for general industrial applications, elastomeric sealing lip(s)
HMS5 HMSA10 CRS1 CRSA1 CRSH1 CRSHA1
CRW1 CRWH1 CRWA1 CRWHA1 CRW5 CRWA5
HDW1 HM14 TL7 X15
Seals for general industrial applications, PTFE sealing lip(s)
SL SLA SLX SLS DL DLA
YSLE YNSLE YSL
Product data – general
Seals for heavy industrial applications
HDS7 HDL HDLA HDS1 HDS2 HDSA1
HDSA2 HDSB1 HDSB2 HDSE1 HDSE2 HDSD1
HDSD2 SBF HDS4 HDS6 HS4 HS5
HS6 HS7 HS8 HSF1 HSF2 HSF3
HSF4 HSF5 HSF6 HSF7 HSF8 HSF9
1
Cassette seals, SKF Mudblock
MUD1 MUD2 MUD3 MUD4 MUD5 MUD6
MUD7
Wear sleeves
SKF Speedi-Sleeve LDSLV3 LDSLV4
Axial shaft seals
Track pin seals, SKF Trackstar
TP TPM
Metal face seals
HDDF
V-ring seals
VA/VR1 VS/VR2 VL/VR3 VE/VR4 VRME/VR6
MVR1 MVR2
Axial clamp seals
CT1 CT4
Fig. 1
Selection of seal design and
V-ring
material 1
Selecting an appropriate seal design and material
depends on the operating conditions of the
application such as:
• temperature
• speed
• pressure differential
• type of lubricant
• vertical or horizontal orientation
• runout and shaft-to-bore misalignment
Because the influence of one operating con-

dition typically dominates the seal selection
process, there are no universal rules for deter-
mining the appropriate seal type or design for
Fig. 2
a given application. This section describes how
HMS5 seal operating conditions affect seal performance and
service life and provides guidance on selecting
the most appropriate seal for a given application.
Matrix 1 and 2 on pages 90 to 91 and 198 to
201 list the standard SKF radial shaft seals and
their main features and permissible operating
conditions.
Grease retention
Greases have a relatively high viscosity and are
relatively easy to retain in a bearing arrange-
ment. In many grease lubricated applications, a
non-spring-loaded sealing lip design or a V-ring
can adequately retain the grease († fig. 1).
However, more demanding applications may
require HMS5 or CRW1 spring-loaded radial
Fig. 3
shaft seals († figs. 2 and 3).
CRW1 seal When frequent relubrication is required, the
lip of at least one of the seals in the sealing
arrangement should be directed toward the air
side so that excess grease can escape via the
sealing lip († fig. 3). This avoids grease build-up,
which can retain heat and limit heat dissipation.
For grease lubricated applications, SKF recom-
mends calculating the permissible circumferential
speed for oil and halving the result.
Fig. 4 Oil retention

HMS5 seal Lubricating oils, particularly relatively low-
viscosity oils, are much more difficult to retain
than greases. Therefore, HMS5 or CRW1
spring-loaded radial shaft seals († figs. 4 and 5)
are recommended in order to achieve the neces
sary radial load and resistance to dynamic runout
and shaft-to-bore misalignment for a satisfactory
sealing performance.
Standard HMS5 seals have a straight lip while
CRW1 seals are designed with SKF Wave lips to
provide improved pumping ability, regardless
of the direction of shaft rotation († fig. 6 on
page 57). Another way of increasing a seal’s
pumping ability is to add a helix pattern, i.e.
hydrodynamic features, to the sealing lip design.
The rubber outside diameter, like the one
found on HMS5 seals, helps compensate for
Fig. 5
small imperfections in the housing bore surface
CRW1 seal and is therefore recommended when the re-
quired housing bore surface is questionable.
For very tough operating conditions, where
circumferential speeds are relatively low, metal
face seals, like the HDDF seal († fig. 6), can be
used for both oil or grease retention.
V-rings († fig. 7) may also be used to retain
oil, provided they are installed on the oil side
and supported axially on the shaft.
Fig. 6 Fig. 7
HDDF metal face seal V-ring
Fig. 8 Contaminant exclusion

CRW1 seal Radial shaft seals that are primarily used for
contaminant exclusion should be installed with 1
the lip pointing outward. When additional pro-
tection is needed, SKF recommends a seal design
that incorporates an auxiliary lip, for example the
HMSA10 or CRWA1 seals.
For tough operating conditions, SKF Wave
seals († fig. 8) with hydrodynamic features are
recommended. To further enhance sealing ef-
ficiency, two single-lip seals can be arranged in
tandem († fig. 9) or a double-lip seal, like the
HDSE1 seal, can be used († fig. 10).
V-rings († fig. 11) are used primarily to ex-
clude contaminants. These seals, which act as
flingers, rotate with the shaft and seal against
a surface that is perpendicular to the shaft.
V-rings and axial clamp seals are often used
Fig. 9
as secondary seals to protect the primary seals
CRW1 seals in tandem from coarse contaminants.
None of these seal arrangements are intended
for oil retention.
Fig. 10 Fig. 11
HDSE1 seal V-ring
Fig. 12 Retention and exclusion

HMSA10 seal In many applications, the exclusion of contami-
nants is just as important as lubricant retention.
Seals with an auxiliary lip, like the HMSA10
seals († fig. 12), are appropriate for these
applications.
Another option is to use two seals installed in
opposite directions († figs. 13 and 14) or two
opposing V-rings († fig. 15) with a spacing
washer.
Under extremely tough operating conditions,
SKF recommends using HDDF metal face seals
(† fig. 6 on page 18), provided that the sliding
velocity of the mating surfaces lies within the
permissible range.
Fig. 13
Two seals in opposite direction
Fig. 14 Fig. 15
Two seals in opposite direction V-ring
Fig. 16 Separating two liquids

CRW1 seals When an application has to keep two liquids
from coming into contact with each other, there 1
are two suitable solutions. These solutions,
which depend on the availability of space and
required efficiency, include:
• the use of two separate seals († figs. 16 and

17), positioned with their lips facing in opposite
directions
• the use of HDSD1 double-lip seals († fig. 18)
In both alternatives, the sealing lips must be

spring-loaded. When using an HDSD seal, it is
very important to provide a means to lubricate
the sealing lips, i.e. the cavity between the seal-
ing lips must be filled with grease prior to instal-
lation or during operation via lubrication holes
Fig. 17
drilled through the metal case into the cavity.
HMS5 seals
Fig. 18
HDSD1 seal
Circumferential and rotational speed

The permissible speed of a seal is determined by
its design and sealing lip material as well as the
material and condition of the shaft. All of these
factors influence the heat generation at the seal
counterface. Lubrication of the sealing lip and
the characteristics of the lubricant also have a
direct influence on heat generation because
they have a direct impact on heat dissipation.
Diagram 1 compares the permissible circum-
ferential speeds for various seal designs assum-
ing normal seal operation, grease or oil retention
and no pressure differential across the seal.
Diagram 1
HDDF
CRS1
HMS5
CRW1
HDS2
HS5
solid
HS8
split
1)
VA
CT1
0 5 10 15 20
(984) (1 969) (2 953) (3 937)
Circumferential speed [m/s (ft/min)]
1) Support ring by customer
Fig. 19 Pressure differentials

CRWA5 seal When subjected to a pressure differential, the
seal must resist the additional radial load gener- 1
ated by the pressure. If the seal is not designed
to resist the pressure, it will be forced against
the shaft, increasing the radial load, underlip
temperature, friction and wear of the seal and
the counterface, resulting in shortened service
life.
Standard seals are rated for no more than
0,07 MPa at 5 m/s (10 psi at 1 000 ft/min), but
SKF offers CRW5 and CRWA5 pressure profile
seals that can accommodate 0,34 MPa at 5 m/s
(50 psi at 1 000 ft/min). Beyond 0,34 MPa
(50 psi), SKF offers a line of special order PTFE
seals that can accommodate more than 3,5 MPa
(500 psi).
In applications with pressure differentials,
shaft seals should be secured axially from the
low-pressure side to prevent them from moving
axially. This can be accomplished by installing
the seal into a counterbore († fig. 19) or by
using a retaining ring.
Fig. 20 Limited space

Special seal design In many cases, the available space is insufficient
for a radial shaft seal having dimensions in
accordance with ISO 6194-1 or DIN 3670. In
these situations, special radial shaft seal designs
must be used († fig. 20).
V-rings († fig. 21) are also suitable for
applications with limited space because they
can be positioned outside the actual seal pos
ition. V-rings seal axially by exerting light pres-
sure against the counterface that can be a
stationary or rotating machine component.
In applications with large shaft diameters,
HS8 seals are an appropriate choice when space
is limited († fig. 22).
Fig. 21
V-ring seal
Fig. 22
HS8 seal
Fig. 23 Installation restrictions

V-ring seal In applications where the seal cannot be installed
via the shaft end, a V-ring or any of the split HSF 1
or HS designs can be used († pages 208 to
210).
After being positioned on the shaft, HS and
HSF seals are held together by a spring and
spring connector. These seals should be retained
axially in the housing bore by a one-piece or split
cover plate.
Split HS radial shaft seals are suitable for cir-
cumferential speeds up to 7,5 or 10 m/s
(1 480 or 1 970 ft/min), depending on their
design, and are available for shaft diameters up
to approximately 4 570 mm (180 in.).
Since V-rings are elastic, they can be
stretched and are therefore easy to install, even
in applications where they have to be passed
Fig. 24
over other components († fig. 23). However,
V-ring seals in the event that replacing a V-ring would require
the time consuming removal of several compo-
nents, it is advantageous to install one or two
replacement V-rings on the shaft from the outset
(† fig. 24). When the time comes to replace a
worn V-ring, it can be cut and removed and the
replacement V-ring can be pushed into position.
Fig. 25 Arrangement
V-ring seal Seals installed on vertical shafts are usually
more exposed to contaminants like rain water
than seals on horizontal shafts. Oil retention is
also more challenging for seals installed on ver-
tical shafts. In general, however, all seals listed
in the product tables are suitable for use on both
horizontal and vertical shafts.
V-rings († figs. 25 and 26) have an interfer-
ence fit on the shaft and rotate with it. They act
as flingers and are therefore particularly suit-
able as both primary and secondary seals on
vertical shafts. Highly efficient sealing arrange-
ments, like those found in submersible pumps,
can be achieved using radial shaft seals in tan-
dem with a V-ring for additional protection
against contaminants († fig. 27).
At relatively low speeds, HDDF metal face
Fig. 26
seals († fig. 28) effectively retain grease or oil
V-ring seal and prevent the ingress of contaminants on
vertical shafts.
Fig. 27 Fig. 28
CRW5 seals + V-ring seal HDDF metal face seal
Counterface design
The service life and performance of a seal are
largely influenced by: 1
• shaft material and hardness
• shaft surface finish and tolerance grade
• dynamic runout and shaft-to-bore
misalignment
A shaft surface that is too smooth can lead to

lubricant starvation, while a shaft surface that
is too rough can accelerate sealing lip wear. The
shaft surface should be machined without
directionality as directionality can cause leakage
depending on the direction of rotation. Dynamic
runout and shaft-to-bore misalignment cause
an uneven radial load on the circumference of
the sealing lip. As a result, the sealing lip, par-
ticularly at high speeds, will not be able to follow
the shaft. This, in turn, will result in a gap
between the sealing lip and the shaft, causing
reduced sealing ability.
Unlike radial shaft seals, V-rings and axial
clamp seals are not affected by normal coaxiality
deviations or runout.
Axial movement
Axial movement of the shaft relative to the
housing bore does not detract from the sealing
ability of radial shaft seals († fig. 29), provided
that the total surface in contact with the lip has
the same quality with respect to hardness and
surface finish.
The amount of axial movement that can be
accommodated by V-rings, axial clamp seals and
HDDF seals is limited by the permissible displace
ment of the seal relative to its counterface.
Fig. 29
Axial movement
Radial shaft seals
V-ring seals
Axial clamp seals
Metal face seal
Seal materials SKF Bore Tite Coating

SKF Bore Tite Coating is a water-based acrylic
Cases and inserts sealant available on most SKF metal-cased 1
Metal cases and reinforcements for SKF radial seals. The sealant is used as a coating on the
shaft seals are manufactured standard from outside diameter of the seal. SKF Bore Tite
deep-drawn carbon sheet steel. The exposed Coating is pliable with a thickness of 0,03 to
surfaces are treated to protect them from corro- 0,07 mm (0.0012 to 0.0028 in.) to compensate
sion during normal handling and storage. for small imperfections in the housing bore
SKF radial shaft seals that will be used in cor- surface. The general guideline in Rubber Manu-
rosive environments can also be designed with facturers Association (RMA) is, that if the bore
a stainless steel case on request. surface texture is greater than 2,5 µm (100 µin.)
Ra, a sealant should be used. This sealant can be
used at temperatures up to 200 °C (390 °F) and
Garter springs is compatible with most oils, greases, aqueous
The garter springs on SKF radial shaft seals are acids and alkalis, alcohols and glycols. Please
manufactured standard from cold-drawn steel note that SKF Bore Tite Coating is not compatible
wire. Exceptions are the metal-cased HDS seals, with aromatics, ketones or esters. Contact with
the all-rubber HS seals and the HMS5/HMSA10 these substances will, however, have little or no
seals made from fluoro rubber that are designed effect if wiped off quickly.
with stainless steel garter springs.
Adhesives and bonding agents
Adhesives and bonding agents are used to
achieve static sealing ability and satisfactory
bonding between metal and elastomers in seal
designs. Both of them can be solvent or water
based depending on the metal and elastomer to
be bonded.
Sealing lip materials Details about the chemical resistance of sealing

In addition to its design, the material of a sealing lip materials to various media encountered in
lip can have a significant impact on sealing per- operation are provided in the section Chemical
formance and reliability. SKF, therefore, manu- resistance, page 35.
factures seals using a variety of sealing lip ma- A code is used to identify the sealing lip ma
terials to meet the needs of different applications. terial of SKF seals († table 1). The code also
The sealing lips of SKF seals are generally appears in the designations of metric radial
made of elastomer materials. However, thermo- shaft seals. For seals manufactured from a
plastics like polytetrafluoroethylene (PTFE) are combination of materials, a combination of code
gaining in importance. PTFE is mainly used for letters is used, like RD (nitrile rubber and SKF
special seals intended for particular applications Duralip).
where improved thermal or chemical resistance
is demanded.
SKF industrial shaft seals are generally manu
factured from the materials listed in table 1.
These materials have characteristics that make
them particularly suitable for specific applications.
By changing the actual formulation and blend-
ing, it is possible to modify the characteristics of
the elastomers relative to:
• resistance to swelling
• elasticity
• chemical resistance
• thermal resistance
• behaviour in the cold
• gas permeability
Table 1
SKF sealing lip materials
Composition of basic material Designation according to

SKF IS0 1629 ASTM1) D1418
IS0 1043-1 ASTM D1600
DIN 7728 Part 1
Acrylonitrile-butadiene rubber (nitrile rubber) R, RG NBR NBR
Hydrogenated acrylonitrile-butadiene rubber H HNBR HNBR

(SKF Duratemp)
Carboxylated nitrile rubber (SKF Duralip) D XNBR XNBR
Polyacrylate elastomer P ACM ACM
Silicone rubber S MVQ VMQ
Fluoro rubber (SKF Duralife2)) V FPM FKM
Polytetrafluoroethylene T PTFE PTFE
1) American Society for Testing and Materials

2) Previously named LongLife
Nitrile rubber (R) SKF Duratemp (H)

The term nitrile rubber is used in this publi SKF Duratemp is a hydrogenated nitrile rubber
cation for acrylonitrile-butadiene rubber (NBR). (HNBR) developed by SKF that combines the 1
This material has very good engineering prop- wear resistance of SKF Duralip with increased
erties and is a general-purpose sealing lip ma- high-temperature resistance († diagram 3 on
terial. It is a copolymer manufactured from page 34). SKF Duratemp is also more resistant
acrylonitrile and butadiene that provides good to chemical attack, weather, ageing and ozone.
resistance to the following media: However, mixtures of oil in air may have a nega-
tive effect. The upper operating temperature
• Most mineral oils and greases with a mineral limit is 150 °C (300 °F), which is significantly
oil base higher than that of ordinary nitrile rubber. SKF
• Normal fuels like gasoline, diesel and light Duratemp is mainly used for seals for heavy in-
heating oils dustrial applications or where extended service
• Animal and vegetable oils and fats and hot life is required.
water
Nitrile rubber also tolerates short-term dry

running of the sealing lip. The permissible oper-
ating temperature range of nitrile rubber is –40
to +100 °C (–40 to +210 °F). For brief periods,
temperatures of up to 120 °C (250 °F) can be
tolerated.
SKF also offers a special nitrile rubber com-
pound with a temperature range between –55
and +110 °C (–65 and +230 °F).
SKF Duralip (D)

SKF Duralip is a carboxylated nitrile rubber
(XNBR) developed by SKF that combines the
good technical properties of nitrile rubber with
an increased resistance to wear († diagram 2
on page 33). It is mainly used for seals for heavy
industrial applications. Seals made of this ma
terial should be chosen when abrasive contam-
inants like sand, soil and scale could reach the
seal counterface on the shaft.
SKF Duralife1) (V)

WAR N I N G :
The fluoro rubber (FKM) compound, SKF Duralife,
At temperatures above 300 °C (570 °F),
has been developed by SKF and is characterized
all fluoro elastomers and PTFE compounds
by its very good wear, thermal and chemical
give off dangerous fumes. This can occur,
resistance. Its resistance to weather and ageing
for example, if a welding torch is used when
from UV light and ozone is also very good and its
removing a bearing. Although the fumes
gas permeability is very slight.
are only produced at such high tempera-
SKF Duralife has exceptional properties even
tures, once heated, the seals will be dan-
under harsh environmental conditions and can
gerous to handle even when they have
withstand operating temperatures ranging from
cooled down. If it is necessary to handle
–20 to +200 °C (–5 to +390 °F). In applications
PTFE or fluoro elastomer seals that have
with low dynamic runout, the temperature
been subjected to the high temperatures
range can be extended down to –40 °C (–40 °F).
mentioned above, the following safety
SKF also offers special low-temperature fluoro
precautions should be observed:
rubber compounds on request.
SKF Duralife is also resistant to oils and hy-
• Protective goggles and gloves should
draulic fluids, fuels and lubricants, mineral acids
always be worn.
and aliphatics as well as aromatic hydrocarbons
• The remains of seals should be put in
that would cause many other seal materials to
an airtight plastic container marked
fail. Seals made of SKF Duralife can also tolerate
“Material will etch”.
dry running of the lip for short periods. The
• Comply with the safety precautions
seals should not be used in the presence of es-
included in the material safety data that
ters, ethers, ketones, certain amines and hot
can be provided upon request.
anhydrous hydrofluorides. Because of the com-
pound’s valuable properties, SKF manufactures
If there is contact with your skin, this
seals with sealing lips made of SKF Duralife for
should be washed with soap and plenty
all common shaft diameters.
of water. Wash your eyes with plenty of
Polytetrafluoroethylene (PTFE) water if these materials get into your eyes.
A doctor should always be consulted. This
PTFE is a thermoplastic polymer that is compat-
also applies if the fumes have been inhaled.
ible with a wide assortment of lubricants and
features chemical resistance that is far superior
to that of any other sealing lip material. PTFE
has a smooth, dirt-resistant surface. Seals with
PTFE lips can accommodate high surface speeds
while offering extended service life. The seals
can tolerate dry running and are particularly
valuable in highly contaminated applications
because of their excellent exclusion ability. PTFE
is used for auxiliary seal elements or for primary
sealing lips for special applications. For optimum
performance, PTFE seal elements require a
high-quality seal counterface and extra care
during installation. The normal operating
temperature range extends from –70 to +200 °C
(–90 to +390 °F), but may go up to 250 °C
(480 °F).
1) Previously named LongLife
Polyacrylate elastomer Wear resistance

Polyacrylate elastomers are more heat resistant
than nitrile rubber or SKF Duralip. The operating The wear resistance of a seal depends largely on 1
temperature range for polyacrylate elastomers the sealing lip material, as well as on the shaft
lies between –40 and +150 °C (–40 and +300 °F) surface finish, type of lubricant, circumferential
and in some fluids the upper limit may be ex- speed, temperature and pressure differentials.
tended to 175 °C (345 °F). Seals of polyacrylate A comparison of wear resistance for various
are resistant to ageing and ozone and are also sealing lip materials used by SKF is provided in
suitable for use with lubricants containing EP diagram 2. It is valid for seals of the same size,
additives. They should not be used to seal water, operating under identical conditions.
acids or alkalis etc. Dry running should be
avoided.
Silicone rubber
Silicone rubber is characterized by high thermal
resistance and can withstand temperatures
ranging from –70 to +160 °C (–90 to +320 °F).
Silicone rubber absorbs lubricants, thereby min-
imizing friction and wear. SKF silicone rubber
seals are particularly suitable for applications
with very low or very high temperatures and for
low-friction sealing of bearing arrangements.
They are not very resistant to oxidized oils or
certain EP additives and should be protected
against abrasive substances. Sealing lips made
of silicone rubber should not be exposed to dry
running.
Diagram 2
Wear resistance
Silicone
rubber
Polyacrylate
elastomer
Nitrile rubber
Carboxylated nitrile rubber (SKF Duralip)
Hydrogenated nitrile rubber (SKF Duratemp)
Fluoro rubber (SKF Duralife)
Polytetrafluoroethylene
Operating temperatures also be affected if these components are made

of different materials with significantly different
Both low and high temperatures influence the coefficients of expansion and shrinkage.
sealing performance. At low temperatures, the Refer to diagram 3 to view the permissible
sealing lip loses its elasticity and becomes hard operating temperature ranges of sealing lip
and brittle. Sealing efficiency decreases and the materials normally used by SKF.
seal becomes more susceptible to mechanical
damage.
For applications where temperatures are con-
tinuously high, special high-temperature lip
materials should be used, for example, PTFE or
the SKF fluoro rubber material, SKF Duralife.
Friction, circumferential speed, viscosity of
the medium being sealed as well as the specific
heat transfer along the shaft influence the tem-
perature at the sealing position and the tem
perature between the lip and lubricant film on
the counterface. High temperatures generally
lead to a breakdown of the lubricant film, result-
ing in insufficient lubrication, one of the most
common causes of premature seal failure.
The static sealing ability between the outside
diameter of the seal and the housing bore may
Diagram 3
Permissible operating temperatures
Nitrile rubber
SKF Duralip
SKF Duratemp
Polyacrylate elastomer
Silicone rubber
SKF Duralife
Polytetrafluoroethylene
–80 –60 –40 –20 0 +50 +100 +150 +200 +250

(–112) (–76) (–40) (–4) (+32) (+122) (+212) (+302) (+392) (+482)
Temperature [°C (°F)]
Chemical resistance
In table 2, Chemical resistance († pages 36 1
to 43), information is provided regarding the re-
sistance of SKF sealing lip materials to most of
the substances encountered in industrial appli-
cations. The information is based on in-house
testing and the experience of users, as well as
information from the suppliers of the various
materials. Unless otherwise stated, the infor-
mation is valid for media of commercial purity
and quality.
The chemical resistance of a seal is influenced
by temperature, pressure and the amount of
media present. Other important factors to con-
sider when selecting a suitable sealing lip material
include:
• type of service (static or dynamic)

• circumferential speed of the sealing lip
• shaft and housing materials
• surface finish of the seal counterface
Because the above mentioned factors also

influence the service life and performance of
the seal, the information contained in the table
Chemical resistance can only be considered as
a rough guide.
Explanation for table 2 († pages 36

to 43), Chemical resistance
RT = room temperature [20 °C (70 °F)]
1 = minor effect
2 = moderate effect
3 = static only
4 = not recommended
5 = insufficient data, test before use
Table 2
Chemical resistance
Medium Temperature Medium’s effect on sealing lip material
R, D, H V P S
– °C (°F) –
A
Acetaldehycle RT 4 4 4 2
Acetamide RT 1 2 4 2
Acetic acid, 100% (glacial) 60 (140) 3 3 4 2
Acetic acid, 30% RT 2 2 4 1
Acetic acid, 3% (vinegar) RT 2 1 4 1
Acetic anhydride RT / 80 (175) 3 4 4 3
Acetone RT 4 4 4 3
Acetophenone RT 4 4 4 4
Acetylene 60 (140) 1 1 5 2
Acrylonitrile RT / 60 (140) 4 3 4 4
Adipic acid (aq) RT 1 1 5 5
Alum (aq) 100 (210) 1 1 4 1
Aluminium acetate (aq) RT 2 4 4 4
Aluminium chloride (aq) RT 1 1 1 2
Aluminium fluoride (aq) RT 1 1 5 2
Aluminium nitrate (aq) RT 1 1 5 2
Aluminium phosphate (aq) RT 1 1 5 1
Aluminium sulphate (aq) RT / 60 (140) 1 1 4 1
Ammonia (anhydrous) RT 2 4 4 3
Ammonia gas RT 1 4 4 2
Ammonia gas 80 (175) / 100 (210) 4 4 4 1
Ammonium carbonate (aq) RT / 60 (140) 2 5 4 5
Ammonium chloride (aq) RT / 60 (140) 1 1 5 5
Ammonium chloride (dry) (sal ammoniac) RT 1 1 1 2
Ammonium nitrate (aq) RT 1 5 2 5
Ammonium persulphate (aq) RT 4 5 4 5
Ammonium phosphate (aq) RT / 60 (140) 1 5 5 1
Ammonium sulphate (aq) 100 (210) 1 4 4 5
Amyl acetate RT 4 4 4 4
Amyl alcohol 60 (140) 2 2 4 4
Aniline 60 (140) / 100 (210) 4 3 4 4
Aniline dyes RT 4 2 4 3
Aniline hydrochloride RT 2 2 4 4
Aniline hydrochloride 100 (210) 4 5 5 5
Animal fats 80 (175) 1 1 1 2
Aqua Regia RT 4 5 4 4
Arsenic acid RT / 60 (140) 1 1 3 1
Arsenic trichloride (aq) RT 1 5 5 5
Asphalt (liquid) 100 (210) 2 2 4 4
B
Barium chloride (aq) RT / 60 (140) 1 1 1 1
Barium hydroxide (aq) RT / 60 (140) 1 1 4 1
Barium sulphate RT / 60 (140) 1 1 4 1
Barium sulphide (aq) RT / 60 (140) 1 1 4 1
Beer RT 1 1 4 1
Benzaldehyde RT / 60 (140) 4 4 4 4
Benzene RT 4 1 4 4
Benzene sulphonic acid RT 4 1 4 4
Benzoic acid RT / 60 (140) 4 1 4 4
Benzoyl chloride RT 4 1 4 5
Benzyl alcohol RT / 60 (140) 4 1 1 2
Benzyl benzoate 50 (120) / 60 (140) 4 1 4 5
Benzyl chloride RT 4 1 4 4
Blast furnace gas 100 (210) 4 1 4 1
Borax (aq) RT / 60 (140) 2 1 5 2
Bordeaux mixture RT 2 1 4 2
Boric acid 60 (140) / 100 (210) 1 1 4 1
Brake fluid, ATE 80 (175) 4 4 4 1
Brake fluid, glycol ether 80 (175) 4 5 4 1
Brine (sodium chloride, aq) RT / 50 (120) 1 1 4 1
Bromine, anhydrous (liquid/gaseous) RT 4 1 4 4
Bromine trifluoride RT 4 4 4 4
Bromine water RT 4 1 4 4
Bromobenzene RT 4 1 4 4
cont. table 2
Chemical resistance

1
R, D, H V P S
– °C (°F) –
Bunker oil 60 (140) 1 1 1 2

Butadiene (gaseous or liquified) RT 4 1 4 4
Butane (gaseous or liquified) RT 1 1 1 4
Butter (animal fat) RT / 80 (175) 1 1 1 2
Butyl acetate RT 4 4 4 4
Butyl acrylate RT 4 4 4 5
Butyl alcohol RT 2 1 4 2
Butyl amines RT 3 4 4 4
Butylene RT 2 1 4 4
Butyl stearate 50 (120) 2 1 5 5
Butyraldehyde RT 4 4 4 4
C
Calcium acetate (aq) RT 2 4 4 4
Calcium bisulphite (aq) RT 1 1 4 1
Calcium chloride (aq) 60 (140) 1 1 1 1
Calcium hydroxide (aq) RT 1 1 4 1
Calcium hypochlorite (aq) RT / 60 (140) 2 1 4 2
Calcium nitrate (aq) RT / 40 (105) 1 1 1 2
Cane sugar liquors RT / 60 (140) 1 1 4 1
Carbon dioxide RT 1 1 5 2
Carbon disulphide RT 3 1 3 4
Carbonic acid RT 2 1 1 1
Carbon monoxide 60 (140) 1 1 5 1
Carbon tetrachloride RT / 60 (140) 3 1 4 4
Castor oil RT 1 1 1 1
Cellosolve (ethyl glycol) RT 4 3 4 4
Cellosolve acetate (ethyl glycol acetate) RT 4 4 4 4
Chlorine (dry) RT 4 1 4 4
Chlorine (wet) RT 4 1 4 4
Chlorine dioxide RT 4 1 4 5
Chlorine trifluoride RT 4 4 4 4
Chloroacetic acid 60 (140) 4 4 4 5
Chloroacetone RT 4 4 4 4
Chlorobenzene RT 4 1 4 4
Chlorobromomethane RT 4 1 4 4
Chlorobutadiene RT 4 1 4 4
Chloroform RT 4 1 4 4
Chlorosulphonic acid RT 4 4 4 4
Chlorotoluene RT 4 1 4 4
Chromic acid 60 (140) 4 1 4 3
Citric acid 60 (140) / 70 (160) 1 1 5 1
Cobalt chloride (aq) RT 1 1 4 2
Coconut oil 50 (120) / 80 (175) 1 1 1 1
Cod liver oil RT 1 1 1 2
Coke oven gas 80 (175) 4 1 4 2
Copper acetate (aq) RT 2 4 4 4
Copper chloride (aq) RT 1 1 1 1
Copper sulphate (aq) 60 (140) 1 1 4 1
Corn oil RT / 60 (140) 1 1 1 1
Cottonseed oil RT / 70 (160) 1 1 1 1
Cresol 50 (120) / 70 (160) 4 1 4 4
Cumene (isopropylbenzene) RT 4 1 4 4
Cyclohexane RT 1 1 1 4
Cyciohexanol RT 3 1 5 4
Cyclohexanone RT 4 4 4 4
p-Cymene RT 4 1 4 4
D
Decahydronaphthalene (decalin) RT / 60 (140) 4 1 5 4
Detergent RT 1 1 4 1
Developing fluids (photography) RT 1 1 5 1
Diacetone alcohol RT 4 4 4 2
Dibenzyl ether RT 4 4 5 5
Dibutyl amine RT 4 4 4 3
Dibutyl ether RT 4 3 3 4
cont. table 2
Chemical resistance
R, D, H V P S
– °C (°F) –
Dibutyl phthalate RT / 60 (140) 4 3 4 2

Dibutyl sebacate RT / 60 (140) 4 2 4 2
o-Dichlorobenzene RT 4 1 4 4
Dicyclohexylamine RT 3 4 4 5
Diethyl amine RT 2 4 4 2
Diethyl benzene RT 4 1 5 4
Diethyl ether RT 4 4 3 4
Diethyl sebacate RT 2 2 4 2
Diisopropyl benzene RT 4 1 5 5
Dimethyl aniline (Xylidine) RT 3 4 4 4
Dimethyl ether RT 1 2 4 1
Dimethyl formamide RT / 60 (140) 2 4 4 2
Dimethyl phthalate RT 4 2 4 5
Dioctyl phthalate RT / 60 (140) 3 2 4 3
Dioctyl sebacate RT / 60 (140) 4 2 4 3
Dioxane RT / 60 (140) 4 4 4 4
Dioxolane RT 4 4 4 4
Dipentene RT 2 1 4 4
Diphenyl oxide RT 4 1 4 3
Dowtherm oils 100 (210) 4 1 4 3
Dry cleaning fluids 40 (105) 3 1 4 4
E
Epichlorohydrin RT 4 4 4 4
Ethane RT 1 1 1 4
Ethanol (denatured alcohol) RT 1 1 4 1
Ethanolamine (monoethanolamine) RT 2 4 4 2
Ethanolamine (di- and triethanolamine) 50 (120) 5 4 4 2
Ethyl acetate RT 4 4 4 2
Ethyl acrylate RT 4 4 4 2
Ethyl benzene RT 4 1 4 4
Ethyl benzoate RT 4 1 4 4
Ethyl chloride RT 1 1 4 4
Ethylene RT 1 1 5 5
Ethylene chloride RT 4 2 4 4
Ethylene chlorohydrin RT 4 1 4 3
Ethylene diamine RT 1 4 4 1
Ethylene glycol RT 1 1 2 1/2
Ethylene glycol 100 (210) 1 1 3 1/2
Ethylene oxide RT 4 4 4 4
Ethylene trichloride RT 4 1 4 4
Ethyl ether RT 3 4 4 4
Ethyl formate RT 4 1 5 5
Ethyl glycol (Cellosolve) RT 4 3 4 4
Ethyl glycol acetate (Cellosolve acetate) RT 4 4 4 4
Ethyl silicate RT 1 1 5 5
F
Fatty acids 100 (210) 2 1 5 3
Ferric chloride (aq) RT 1 1 1 2
Ferric nitrate (aq) RT 1 1 1 3
Ferric sulphate (aq) RT 1 1 1 2
Fish oil RT 1 1 5 1
Fluorine (liquified) RT 4 2 4 4
Fluorobenzene RT 4 1 4 4
Fluorosilic acid 60 (140) 1 1 5 4
Formaldehyde RT 3 1 4 2
Formaldehyde, 37% below 100 (210) 2 1 4 2
Formic acid RT / 60 (140) 2 3 5 2
Fuels
– Aero engine fuels JP:
– JP3 (MIL-J-5624 G) RT 1 1 2 4
– JP4 (MIL-J-5624 G) RT 1 1 2 4
– JP5 (MIL-J-5624 G) RT 1 1 2 4
– JP6 (MIL-F-25656 B) RT / 60 (140) 1 1 5 4
cont. table 2
Chemical resistance

1
R, D, H V P S
– °C (°F) –
– ASTM reference fuels:

– ASTM-A (MIL-S-3136 B Typ 1) RT / 60 (140) 1 1 2 4
– ASTM-B (MIL-S-3136 B Typ 111) RT / 60 (140) 1 1 5 4
– ASTM-C RT / 60 (140) 2 1 4 4
– Diesel fuel 60 (140) 1 1 2 2
– Fuel oil 60 (140) 1 1 1 4
– Gasohol (10% ethanol or methanol) RT 2 3 4 4
– Kerosene RT 1 1 1 4
– Mineral oil 100 (210) 1 1 1 2
– Petrol RT 1 1 4 4
Fumaric acid RT 1 1 4 2
Furan RT 4 5 4 5
Furfural RT 4 4 4 4
Furfuran RT 4 5 4 5
G
Gelatine (aq) 40 (105) 1 1 4 1
Glucose RT 1 1 5 1
Glue RT 1 1 5 1
Glycerin 100 (210) 1 1 3 1
Glycols 100 (210) 1 1 4 1/2
H
n-Hexaldehyde RT 4 4 5 2
Hexane RT / 60 (140) 1 1 1 4
1-Hexene RT 2 1 1 4
Hexyl alcohol RT 1 1 4 2
Hydraulic fluids
– Hydraulic oils (acc. to DIN 51524) 80 (175) 1 1 1 3
– Hydraulic fluids (acc to DIN 51502):
– HFA (oil in water emulsion) 55 (130) 1 1 5 5
– HFB (water in oil emulsion) 60 (140) 1 1 5 5
– HFC (aqueous Polymer solutions) 60 (140) 1 1 5 1
– HFD (phosphoric esters) 80 (175) 4 2/4 4 4
– Skydrol 500 80 (175) 4 4 4 3
– Skydrol 7000 80 (175) 4 2 4 3
Hydrazine RT 2 4 5 3
Hydrobromic acid RT / 60 (140) 4 1 4 4
Hydrochloric acid (conc.) RT 3 1 4 3
Hydrochloric acid (conc.) 80 (175) 4 2 4 4
Hydrocyanic acid (Prussic acid) RT 2 1 4 3
Hydrofluoric acid (conc.) RT 4 1 4 4
Hydrofluoric acid (conc.) 100 (210) 4 3 4 4
Hydrofluoric acid (anhydrous) 100 (210) 4 4 4 4
Hydrogen gas RT 1 1 2 3
Hydrogen peroxide (90%) RT 4 2 4 2
Hydrogen sulphide (wet) RT / 100 (210) 4 4 4 3
Hydroquinone RT 4 2 4 5
Hypochlorous acid RT 4 1 4 5
I
Iodine pentafluoride RT 4 4 4 4
Isobutyl alcohol RT 2 1 4 1
Isooctane RT 1 1 1 4
Isophorone RT 4 4 4 4
Isopropyl acetate RT / 80 (175) 4 4 4 4
Isopropyl alcohol RT / 60 (140) 2 1 4 1
Isopropyl chloride RT 4 1 4 4
Isopropyl ether RT / 60 (140) 2 4 3 4
L
Lactic acid RT 1 1 4 1
Lactic acid 100 (210) 4 1 4 2
Lard 80 (175) 1 1 1 2
Lavender oil RT 2 1 2 4
Lead acetate (aq) RT / 60 (140) 2 2 4 4
cont. table 2
Chemical resistance
R, D, H V P S
– °C (°F) –
Lead nitrate (aq) RT 1 5 5 2

Linoleic acid RT 2 2 5 2
Linseed oil RT / 60 (140) 1 1 1 1
Lubricants
– ASTM oil No. 1 100 (210) 1 1 1 3
– ASTM oil No. 2 100 (210) 1 1 1 3
– ASTM oil No. 3 100 (210) 1 1 1 3
– ATF oils, type A 100 (210) 1 1 1 4
– ATF oils, type I 100 (210) 1 1 1 4
– ATF oils, type II 100 (210) 1 1 1 4
– ATF oils, type F 100 (210) 1 1 1 4
– ATF oils, type Mercon 100 (210) 1 1 1 4
– EP lubes 100 (210) 2 1 1 4
– Fluorolube 100 (210) 1 2 5 1
– Grease MIL-G-7118 A 80 (175) 1 1 3 3
– Grease MIL-G-7711 A 80 (175) 1 1 1 3
– Lubricating oils (petroleum) 100 (210) 1 1 1 4
– Red oil (MIL-H-5606) 100 (210) 1 1 1 4
– RJ-1 (MIL-F-25558 B) 100 (210) 1 1 1 4
– RP-1 (MIL-F-25576 C) 100 (210) 1 1 1 4
– Motor oil SAE 30 100 (210) 1 1 1 1
– Transmission oil SAE 90 100 (210) 1 1 1 4
– Transmission oil MIL-L-23699 A 100 (210) 1 1 3 3
– Silicone greases 120 (250) 1 1 1 3
– Silicone oils 120 (250) 1 1 1 3
– Transformer oil (Pyranol) 60 (140) 4 1 5 4
– Transformer oil 60 (140) 1 1 2 2
– Transmission fluid type A RT 1 1 1 2
– Turbine oil 100 (210) 2 1 1 4
M
Magnesium chloride (aq) 100 (210) 1 1 5 1
Magnesium hydroxide (aq) 100 (210) 2 1 4 5
Magnesium sulphate (aq) 100 (210) 1 1 4 1
Maleic acid 100 (210) 4 1 4 5
Maleic anhydride 60 (140) 4 4 4 5
Malic acid RT 1 1 4 2
Mercury RT / 60 (140) 1 1 5 5
Mercury chloride (aq) RT / 60 (140) 1 1 5 5
Mesityl oxide RT 4 4 4 4
Methane RT 1 2 1 4
Methanol (methyl alcohol) 60 (140) 1 4 4 1
Methyl acetate RT 4 4 4 4
Methyl acrylate RT 4 4 4 4
Methyl aniline RT 4 2 4 5
Methyl bromide RT 2 1 3 5
Methyl cellosolve (methyl glycol) RT 3 4 4 4
Methyl chloride RT 4 2 4 4
Methyl cyclopentane RT 4 2 4 4
Methylene chloride RT 4 2 4 4
Methyl ethyl ketone RT 4 4 4 4
Methyl formate RT 4 5 5 5
Methyl glycol (Cellosolve) RT 3 4 4 4
Methyl isobutyl ketone RT 4 4 4 4
Methyl methacrylate RT 4 4 4 4
Methyl salicylate RT 4 5 5 5
Milk RT 1 1 4 1
Mustard gas RT 5 5 5 1
N
Naphtha RT 2 1 2 4
Naphthalene 60 (140) 4 1 5 4
Naphthalenic acid RT 2 1 5 4
Natural gas RT 1 1 2 1
Neat-s-foot oil RT / 60 (140) 1 1 1 2
Nickel acetate (aq) RT 2 4 4 4
cont. table 2
Chemical resistance

1
R, D, H V P S
– °C (°F) –
Nickel chloride RT 1 1 4 1
Nickel sulphate (aq) RT / 60 (140) 1 1 4 1
Nitric acid (conc.) RT 4 3 4 4
Nitric acid (fuming) RT 4 4 4 4
Nitric acid (dilute) RT 4 1 4 2
Nitrobenzene 50 (120) 4 2 4 4
Nitroethane RT 4 4 4 4
Nitrogen RT 1 1 1 1
Nitrogen tetroxide RT 4 4 4 4
Nitromethane RT 4 4 4 4
0
Octadecane RT / 50 (120) 1 1 2 4
n-Octane RT 2 1 4 4
Octyl alcohol RT 2 1 4 2
Oleic acid 70 (160) 1 2 2 4
Olive oil 60 (140) 1 1 1 3
Oxalic acid 70 (160) 2 1 5 4
Oxygen RT 2 1 2 1
Oxygen > 100 (210) 4 2 4 2
Ozone RT 4 1 2 1
P
Palmitic acid 60 (140) 1 1 4 4
Peanut oil RT / 50 (120) 1 1 1 1
Perchloric acid RT 4 1 4 4
Perchloroethylene RT / 60 (140) 2 1 4 4
Petroleum below 120 (250) 1 1 2 2
Petroleum above 120 (250) 4 2 4 4
Petroleum ether RT / 60 (140) 1 1 1 4
Petroleum gas (liquified) RT 1 1 3 3
Phenol 60 (140) / 100 (210) 4 1 4 4
Phenyl ethyl ether RT 4 4 4 4
Phenyl hydrazine RT / 60 (140) 4 1 4 5
Phoron (diisopropylidene acetone) 60 (140) 4 4 4 4
Phosphoric acid, 20% 50 (120) / 60 (140) 2 1 5 2
Phosphoric acid, 45% 50 (120) / 60 (140) 4 1 5 3
Phosphorus trichloride RT 4 1 5 5
Pickling solution RT 4 2 4 4
Picric acid RT 4 1 5 4
Pinene RT 2 1 4 4
Pine oil RT 4 1 5 4
Piperidine RT 4 4 4 4
Potassium acetate (aq) RT 2 4 4 4
Potassium chloride (aq) RT / 60 (140) 1 1 1 1
Potassium cyanide (aq) RT / 50 (120) 1 1 1 1
Potassium dichromate (aq) RT 1 1 1 1
Potassium hydroxide (aq) 60 (140) 2 4 4 4
Potassium nitrate (aq) RT / 60 (140) 1 1 1 1
Potassium sulfate (aq) RT / 60 (140) 1 1 4 1
Propane RT 1 1 1 4
Propyl acetate RT 4 4 4 4
Propyl alcohol RT / 60 (140) 1 1 4 1
Propylene RT 4 1 4 4
Propylene oxide RT 4 4 4 4
Prussic acid (hydrocyanic acid) RT 2 1 4 3
Pyridine RT 4 4 4 4
Pyroligneous acid RT 4 4 4 5
Pyrrole RT 4 4 4 2
R
Rapeseed oil RT 2 1 2 4
Refrigerants (acc. to DIN 8962)
– R 11 RT 2 1 5 4
– R 12 RT 1 2 1 4
– R 13 RT 1 1 5 4
cont. table 2
Chemical resistance
R, D, H V P S
– °C (°F) –
– R 13 B1 RT 1 1 5 4
– R 14 RT 1 1 5 4
– R 21 RT 4 4 5 4
– R 22 RT 4 4 2 4
– R 31 RT 4 4 5 5
– R 32 RT 1 4 5 5
– R 112 RT 3 1 5 4
– R 113 RT 1 2 5 4
– R 114 RT 1 2 5 4
– R 114 B2 RT 2 2 5 4
– R 115 RT 1 2 5 5
– R C 318 RT 1 2 5 5
S
Salicylic acid RT 2 1 5 5
Sea water RT 1 1 4 1
Silver nitrate (aq) RT 2 1 1 1
Soap solution RT 1 1 4 1
Sodium acetate (aq) RT 2 4 4 4
Sodium bicarbonate (aq) 60 (140) 1 1 5 1
Sodium bisulphite (aq) 100 (210) 1 1 4 1
Sodium carbonate (soda) RT / 60 (140) 1 1 5 1
Sodium chloride (aq) RT / 100 (210) 1 1 5 1
Sodium cyanide (aq) RT 1 1 5 1
Sodium hydroxide (aq) RT 2 2 3 2
Sodium hypochlorite (aq) RT / 50 (120) 2 1 4 5
Sodium metaphosphate RT / 60 (140) 1 1 5 2
Sodium nitrate (aq) RT / 60 (140) 2 5 5 4
Sodium phosphate (aq) RT / 60 (140) 1 1 4 4
Sodium silicate (aq) RT / 60 (140) 1 1 5 5
Sodium sulphate (aq) (Glauber’s salt) RT / 60 (140) 1 1 4 1
Sodium thiosulphate (aq) RT / 50 (120) 2 1 4 1
Soyabean oil RT 1 1 1 1
Stannic chloride (aq) RT / 80 (175) 1 1 5 2
Stannous chloride (aq) RT / 80 (175) 1 1 5 2
Steam below 150 (300) 4 4 4 3
Steam above 150 (300) 4 4 4 4
Stearic acid 60 (140) 2 2 4 2
Stoddard solvent RT 1 1 1 4
Styrene RT 4 2 4 4
Sucrose solution RT / 60 (140) 1 1 4 1
Sulphur RT / 60 (140) 4 1 4 3
Sulphur chloride (aq) RT 3 1 4 3
Sulphur dioxide (dry) RT / 60 (140) 4 1 4 2
Sulphur dioxide (liquified) RT / 60 (140) 4 1 4 2
Sulphur dioxide (wet) RT / 60 (140) 4 1 4 2
Sulphur hexafluoride RT 2 1 4 2
Sulphuric acid (conc.) RT / 50 (120) 4 1 4 4
Sulphuric acid (20%) (battery acid) 60 (140) 4 1 4 4
Sulphuric acid (dilute) RT 3 1 2 4
Sulphurous acid RT / 60 (140) 4 1 4 4
Sulphur trioxide RT 4 1 4 2
T
Tannic acid RT / 60 (140) 1 1 4 2
Tar, bituminous RT 2 1 4 2
Tartaric acid 60 (140) 1 1 5 1
Tepineol RT 2 1 5 5
Tetrabromoethane RT 4 1 4 4
Tetrabromomethane RT 4 1 5 4
Tetrabutyl titanate RT 2 1 5 5
Tetrachloroethylene 60 (140) 4 2 4 4
Tetraethyl lead RT 2 1 5 5
Tetrahydrofuran RT 4 4 4 4
Tetrahydronaphthalene (Tetralin) RT 4 1 5 4
Thionyl chloride RT 4 2 4 5
cont. table 2
Chemical resistance

1
R, D, H V P S
– °C (°F) –
Titanium tetrachloride RT 2 1 4 4
Toluene RT 4 1 4 4
Toluene diisocyanate RT 4 4 4 4
Triacetin RT 2 1 4 5
Tributoxy ethyl phosphate RT 4 1 4 5
Tributyl phosphate RT / 60 (140) 4 4 4 4
Trichloroacetic acid 60 (140) 5 4 4 4
Trichloroethane RT 4 1 4 4
Trichloroethylene RT 4 1 4 4
Tricresyl phosphate RT / 60 (140) 4 1 4 3
Triethanol amine RT 2 4 4 5
Triethyl aluminium RT 4 2 4 5
Triethyl borane RT 4 1 4 5
Trinitrotoluene RT 4 2 4 5
Trioctyl phosphate RT / 60 (140) 4 2 4 3
Tung oil (China wood oil) RT 1 1 1 4
Turpentine RT 1 1 2 4
V
Varnish RT 2 1 4 4
Vegetable oil 60 (140) 1 1 1 2
Vinyl acetylene RT 1 1 5 2
Vinyl chloride RT 4 1 5 5
W
Water 100 (210) 1 1 4 1
Whisky RT 1 1 4 1
White oil RT / 80 (175) 1 1 1 4
Wine RT 1 1 4 1
Wood oil RT 1 1 1 4
X
Xylene RT 4 1 4 4
Xylidine (di-methyl aniline) RT 3 4 4 4
Z
Zeolites RT 1 1 5 5
Zinc acetate (aq) RT 1 1 4 4
Zinc chloride (aq) RT 1 1 4 1
Zinc sulphate (aq) RT 1 1 4 1
Storage and handling of seals orange coating (never blue). Ordinary light bulbs
are preferred for illumination.
General Seals should be wrapped or stored in airtight
The following guidelines for the storage and containers, protecting them from atmospheric
cleaning of seals are valid for natural and syn- changes and particularly against drafts.
thetic elastomer materials and are in accord- Because ozone is particularly damaging,
ance with ISO 2230 and DIN 7716 standards. steps must be taken to make sure that no ozone
The storage guidelines set forth in DIN 7716 is produced in the storage facility as the result of
are valid for long-term storage. using electric motors or other equipment that
Unfavourable storage conditions and improper can produce sparks or other electric discharges.
handling can change the physical properties of Combustion fumes and vapours that can pro-
most products made from natural or synthetic duce ozone as the result of photochemical pro
rubber. This can result in hardening or soften- cesses should be exhausted. For this reason,
ing, permanent deformation, peeling or cracks, solvents, fuels, lubricants, chemicals, acids, dis-
which can lead to a shortened service life or infectants etc. should not be stored in the same
render the products altogether useless. These room as the seals.
changes can be brought about by storing the Elastomer products should not be subjected
products under stress or load or from the influ- to tension, compression or other forms of load
ence of oxygen, ozone, heat, light, moisture or during storage as this can produce permanent
solvents. When stored properly, elastomer prod- deformations and cracks. Seals should therefore
ucts generally retain their properties for several not be hung on hooks during storage. Certain
years. metals, especially copper and manganese, dam-
age elastomer products. Contact with these
metals should therefore be avoided and the
Storage seals should be covered with layers of paper or
The storage area should be cool, dry, moderately polyethylene to prevent such contact.
ventilated and there should be as little dust as In case it is necessary to repack the seals,
possible. Outdoor storage without protection packaging and covering materials should not
should be avoided. contain substances such as copper or alloys
The appropriate storage temperature depends containing copper, petroleum, oil etc. that can
on the elastomer. The most favourable storage cause damage to the seals. The packaging
temperature for synthetic rubber seals is 15 to materials should not contain softeners.
25 °C (60 to 80 °F). If the products are powdered, suitable powders
Elastomer products that have been subjected are talcum, chalk, finely divided glimmer and
to low temperatures during transport or storage rice starch.
may become stiff. They should therefore be Seals made of different materials should not
warmed and kept at a temperature of at least be in contact with each other. This is particularly
20 °C (70 °F) before being unpacked and used in important when the seals are different in colour
order to prevent exposure to condensation. as this will avoid discolouration.
In heated storage rooms, the products should Seals should be stored for the shortest period
be shielded from the heat source. There should of time possible. Where long-term storage is in-
be at least 1 m (3 ft.) between the packages and volved, care should be taken that newly arrived
the source of heat. In rooms where a heater products are kept separate from those already
with a fan is used, the distance should be greater. in storage to enable use of seals on a first in,
Storage in damp rooms should be avoided be- first out basis.
cause of the risk of condensation. A storage fa-
cility with relative humidity below 65% is
excellent.
Seals should be protected from light, particu-
larly direct sunlight or artificial light with a high
proportion of UV radiation. Any windows in the
store should therefore be covered with a red or
Cleaning and maintenance

In the event that cleaning is necessary, elasto
mer products should be cleaned with warm, 1
soapy water that does not exceed 30 °C (85 °F),
and air dried at room temperature.
Solvents such as trichloroethylene, carbon
tetrachloride or hydrocarbons should not be
used, nor should sharp-edged objects, wire
brushes, emery cloth or sandpaper.
Elastomer/metal combinations can be cleaned
using a 1:10 mixture of glycerine and alcohol.
www.nguyenxuong.com
Radial shaft seals
General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Outside diameter design. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

SKF Bore Tite Coating. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Garter springs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Tolerances. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Sealing lip design. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Auxiliary lips. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Coaxiality and runout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Coaxiality. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Runout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Axial movement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Permissible speed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Lubrication. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Lubrication of paired arrangements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Friction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
Chemical and thermal resistance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Seals under pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Shaft requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Tolerances. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Surface roughness. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70
Surface finish. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Hardness and surface treatment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Lead-in chamfers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Housing bore requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Metal-reinforced seals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Seals without metal-reinforcement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Tolerances. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Surface roughness. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Seal installation, general industrial applications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Seal installation, heavy industrial applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Metal-reinforced seals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79
Seals without metal reinforcement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Split seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Cover plates. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Multiple HS seal installations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
Multiple HDS seal installations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
PTFE seals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Protecting the counterface surface against corrosion. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Removal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87
Designation system. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Metric radial shaft seals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Inch-size radial shaft seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Assortment and availability. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Seals for general industrial applications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92

HMS5 and HMSA10 seals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
2.1 Product table: HMS5 and HMSA10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
CRW1, CRWA1, CRWH1 and CRWHA1 seals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
2.2 Product table: CRW1, CRWA1, CRWH1 and CRWHA1 . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
CRW5 and CRWA5 seals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 160
2.3 Product table: CRW5 and CRWA5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
HDW1 seals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
2.4 Product table: HDW1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 164
CRS1, CRSH1, CRSA1 and CRSHA1 seals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
2.5 Product table: CRS1, CRSH1, CRSA1 and CRSHA1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 167
PTFE radial shaft seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 174
HM and TL seals for grease lubricated applications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178
2.6 Product table: HM and TL seals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 179
X seals, sealing against housing bore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192
2.7 Product table: X seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 193
Seals for heavy industrial applications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202
Metal-cased seals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 202
Rubber outside diameter seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 207
Additional design features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 211
Size options of metal-cased HDS seals and all-rubber HS seals. . . . . . . . . . . . . . . . . . . . . . . . . . . 215
Product tables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 216

2.8 HDS7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 216
2.9 HDS7K. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222
2.10 HDL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 226
2.11 HDS1, HDS2 and HDS3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 242
2.12 HDS1K. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 258
2.13 HDS2K. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260
2.14 HDSF and HDSH seals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 262
2.15 HDSA and HDSB seals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 264 2
2.16 HDSE1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 270
2.17 HDSD and HDSE seals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 272
2.18 SBF. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 274
2.19 HSF1 (split) and HSF5 (solid). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 276
2.23 HSF9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300
2.24 HS4 and HS5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 302
2.25 HS6, HS7 and HS8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 306
Radial shaft seals
General • A sealing lip made of an elastomeric or thermo

plastic material that seals dynamically and
Radial shaft seals are used between rotating statically against the shaft. The lip has a seal-
and stationary machine components († fig. 1) ing edge that is formed by moulding, cutting
or between two components in relative motion or grinding. It is normally pressed against the
and consist of two main parts: counterface surface of the shaft, with a defined
radial load, by a garter spring. The edge of the
• A cylindrical outer covering of sheet steel sealing lip and the shaft counterface surface
(case) or an elastomer that has the requisite form the most important functional area of a
interference fit to seal statically against the radial shaft seal. The sealing effect of the lip
housing bore. can be enhanced by designing the contact
area of the lip with hydrodynamic features.
Fig. 1
Radial shaft seal, HMS5
Some radial shaft seal designs have an auxil-

iary lip that protects the primary sealing lip from
dust and other contaminants. A suitable lubricant
in the space between the primary sealing lip and
the auxiliary lip can reduce wear and delay cor-
rosion. Contaminants that have passed the aux-
iliary lip will eventually cause damage in the
counterface surface area. A build-up of heat can
also occur between the two lips, resulting in 2
premature wear.
Radial shaft seals are used in a multitude of
applications. Because of the importance of ra-
dial shaft seals for the operational reliability and
service life of machines and equipment, both
seal manufacturers and users are equally inter-
ested, to some degree, in standardization. This
has led to the establishment of national and
international standards and guidelines listed in
table 1 on page 53. These cover boundary
dimensions, tolerances, material specifications,
test methods and terminology as well as the
basic outside diameter constructions and sealing
lip arrangements.
See figs. 2 and 3 on page 52 for the termin
ology used in this publication.
Radial shaft seals
Fig. 2
Metal-cased seal with spring-loaded sealing lip
Outside diameter Case
Front chamfer Back chamfer
Front face Back face
Garter spring Flex section
Heel
Spring-retaining lip
Spring groove Lip back face
Lip front face Sealing edge
Lip Relative spring position
Front side Back side
Fig. 3
Rubber outside diameter seal with spring-loaded sealing lip and auxiliary lip
Metal insert
Auxiliary lip back face

Sealing lip
Auxiliary lip
Auxiliary lip front face
Table 1
Standards and other documents relating to radial shaft seals
Document1) Title
ISO 2230 Rubber products – guidelines for storage
ISO 6194-1 Rotary shaft lip-type seals – Nominal dimensions and tolerances
ISO 6194-2 Rotary shaft lip-type seals – Vocabulary 2

ISO 6194-3 Rotary shaft lip-type seals – Storage, handling and installation
ISO 6194-4 Rotary shaft lip-type seals – Performance test procedures
ISO 6194-5 Rotary shaft lip-type seals – Identification of visual imperfections
SAE J946 Application guide to radial lip seals
RMA OS-1-1 Shaft requirements for rotary shaft seals
RMA OS–4 Application guide for radial lip type shaft seals
RMA OS–7 Storage and handling guide for radial lip type shaft seals
RMA OS–8 Visual variations guide for rotating shaft seals
DIN 3760 Radial-Wellendichtringe (Radial shaft seals)
DIN 3761 Radial-Wellendichtringe für Kraftfahrzeuge (Radial shaft seals for motor vehicles), Parts 1 to 15.
This standard covers all aspects including vocabulary, material requirements and test methods.
DIN 7172 Tolerances and limit deviations for sizes above 3 150 mm up to 10 000 mm.
DIN 7716 Rubber products; requirements for storage, cleaning and maintenance.
1) RMA = Rubber Manufacturers Association

SAE = Society of Automotive Engineers
ISO = International Organization for Standardization
DIN = Deutsches Institut für Normung
Radial shaft seals
Outside diameter design Fig. 4
Outside diameter designs

The standard assortment of radial shaft seals
manufactured by SKF for general industrial
applications covers three different outside
diameter executions († figs. 4a to 4c).
Seals with a rubber outside diameter
(† fig. 4a) are used in a wide range of applica-
tions. They maintain a tight fit in the housing
bore when the housing material has a higher
coefficient of thermal expansion than steel and/ a b
or when the housing is split. They are also rec-
ommended in all applications where the housing
bore surface finish requirements cannot be met.
Metal-cased seals († fig. 4b) are multi-pur-
pose seals that can be used for most applications.
They are relatively easy to install and, provided
the housing bore meets the requirements, will
fit tightly and centrically in the housing bore.
Radial shaft seals designed with a metal case
and a secondary reinforcement in the side face c d
(† fig. 4c) offer advantages where operating
conditions are severe. They have a higher radial
stiffness and are available for shaft diameters
≥ 50 mm (2 in.).
Besides these standard outside diameter
designs, there is also a half rubber / half metal
outside diameter design († fig. 4d) that is
typically used in automotive applications.
In addition to the seal designs for general
industrial applications described above, SKF
also manufactures seals for heavy industrial
applications with special features to meet
specific requirements († page 202).
SKF Bore Tite Coating

As the static sealing ability between a metal out-
side diameter and the housing bore is somewhat
limited, particularly in the case of low-viscosity
fluids and media that can “creep”, most SKF
seals with a metal case feature SKF Bore Tite
Coating, a water-based acrylic sealant. SKF
Bore Tite Coating is green in colour, does not
harden and serves to fill small imperfections
in the housing bore. For additional details, refer
to page 29.
Garter springs
SKF radial shaft seals have garter springs made
of drawn carbon steel or stainless steel spring
wire. Carbon steel springs are standard unless
otherwise specified.
Dimensions 2
SKF radial shaft seals are manufactured for
a wide range of shaft diameters, from 5 to
4 600 mm (0.2 to 181 in.). The range also in-
cludes standard sizes in accordance with
ISO 6194-1 and DIN 3760 for shafts ranging
from 6 to 500 mm (0.24 to 19.7 in.).
Tolerances
SKF radial shaft seals are generally manufac-
tured to the outside diameter tolerances listed
in table 2 on page 56, for metric seals, and
table 3 on page 56 for inch-size seals. These
are, where standardized, in accordance with
ISO 6194-1, DIN 3760 and RMA OS-4.
Radial shaft seals
Table 2
Outside diameter tolerances for metric seals
Nominal seal outside Seals with outside diameter of

diameter steel elastomer1)
D Seal outside diameter tolerance Seal outside diameter tolerance

over incl. high low high low
mm mm mm
50 +0,20 +0,08 +0,30 +0,15

50 80 +0,23 +0,09 +0,35 +0,20
80 120 +0,25 +0,10 +0,35 +0,20
120 180 +0,28 +0,12 +0,45 +0,25

180 300 +0,35 +0,15 +0,45 +0,25
300 500 +0,45 +0,20 +0,55 +0,30
500 630 +0,50 +0,22 – –

630 800 +0,50 +0,24 – –
800 1 000 +0,55 +0,25 – –
1 000 1 250 +0,60 +0,27 – –

1 250 1 600 +0,65 +0,30 – –
1) Seals
with beaded outside diameter require different tolerances.
Contact SKF for sizes outside the listed range.
Table 3
Outside diameter tolerances for inch-size seals
Bore diameter1) Seals with outside diameter of

steel elastomer
D Tolerance Nominal seal Seal outside Nominal seal Seal outside

over incl. outside diameter diameter tolerance outside diameter diameter tolerance
in. in. in.
2.000 ±0.001 +0.005 ±0.002 +0.008 ±0.003

2.000 3.000 ±0.001 +0.0055 ±0.0025 +0.01 ±0.003
3.000 4.000 ±0.0015 +0.0065 ±0.003 +0.0105 ±0.003
4.000 5.000 ±0.0015 +0.0065 ±0.003 +0.0105 ±0.003

5.000 7.000 ±0.0015 +0.007 ±0.003 +0.012 ±0.004
7.000 9.000 ±0.002 +0.0085 ±0.0035 +0.0125 ±0.004
9.000 10.000 ±0.002 +0.0085 ±0.0035 +0.0125 ±0.004
1) Housing
bores made of material other than steel may need a different nominal press-fit tolerance due to differences
in thermal coefficients of expansion.
Contact SKF for sizes outside the listed range.
Sealing lip design Fig. 5
Conventional sealing lip with straight edge

The form and design of a sealing lip is based on
knowledge gained through research and devel-
opment activities as well as wide practical ex
perience obtained by SKF in close cooperation
with users. The distance between the lip and the
seal back face, the strength of the flex section,
the angle of the lip († fig. 2 on page 52) and 2
the tension in the spring are all balanced so that
the pressure applied by the garter spring pro-
vides a satisfactory sealing performance between
the sealing lip and counterface.
The sealing lips of SKF radial shaft seals are
manufactured from several materials and two
different main designs. The various materials oil side air side
are described on pages 30 to 32. There are two
main sealing lip designs that differ in the exe
Fig. 6
cution of the sealing lip edge. The “conventional”
sealing lip († fig. 5) has a straight edge, SKF Wave sealing lip with sinusoidal sealing lip edge
whereas the SKF Wave lips († fig. 6) are
moulded with a hydrodynamic feature that re-
sults in the lip taking a sinusoidal path on its
counterface surface.
SKF Wave seals represent one of the most
important developments in radial shaft seals.
The sealing lip is moulded to a special form,
producing a relative movement on the counter-
face, imparting hydrodynamic properties. SKF
Wave seals are suitable for rotation in both dir
ections. They pump the lubricant back into the
bearing arrangement and expel contaminants.
The sinusoidal form of the sealing lip consider-
ably extends the path († fig. 6) on the coun- oil side air side
terface surface and at the same time reduces
the specific surface pressure at the sealing lip/
counterface contact.
Radial shaft seals
Diagram 1
As a consequence, SKF Wave seals produce
up to 20% less friction resulting in up to 30% Temperature rise at sealing lip/counterface contact for
lower temperatures than conventional lip de- conventional and SKF Wave lips as a function of rotational
speed for a 76 mm diameter shaft with SAE 30 engine oil
signs († diagrams 1 and 2). Reduced friction
and the sinusoidal path of the sealing lips help
prevent the formation of deep tracks in the
counterface, resulting in significantly extended
service life. SKF Wave seals are recommended Temperature rise [°C (°F)]
where demands for operational reliability and 60 (140)
long service life for machines and equipment
are high. 50 (122)
Conventional lip
SKF seals with conventional spring-loaded
sealing lips meet general demands because they
40 (104)
are able to provide efficient sealing even under
unfavourable operating conditions. To improve
sealing performance, some SKF radial shaft 30 (86)
seals are designed with hydrodynamic features SKF Wave lip
on the sealing lip. These have either a right- 20 (68)
hand twist for shafts that rotate clockwise, or a
left-hand twist for shafts that rotate counter-
clockwise as seen from the air side. The degree 10 (50)
to which the hydrodynamic feature improves the
sealing ability depends on the form of the spiral 0 (32)
flutes, the circumferential speed, the pressure 0 1 000 2 000 3 000 4 000 5 000
conditions and the media being sealed. See also Speed [r/min]
paragraph Oil retention on page 18.
Diagram 2
Auxiliary lips Frictional moment at sealing lip/counterface contact for

conventional and SKF Wave lips as a function of rotational
speed for a 76 mm diameter shaft with SAE 30 engine oil
SKF radial shaft seals can also be designed with
an auxiliary lip for increased protection against
contaminants († fig. 3 on page 52). These
auxiliary lips are either contacting or non-con-
tacting. Seal designs that incorporate contacting Frictional moment [Nm (ozf/in.)]
auxiliary lips are used in heavily contaminated
environments, with the drawback, however, of Conventional lip
0,8 (113)
creating increased friction and elevated underlip
temperatures. The auxiliary lip of HMSA10 and
CRWA1/CRWHA1 seals is non-contacting, which
0,6 (85)
means that these designs normally can be used SKF Wave lip
at the same speeds as the single-lip designs
HMS5 and CRW1/CRWH1.
0,4 (57)
0,2 (28)
0
0 1 000 2 000 3 000 4 000 5 000
Speed [r/min]
Coaxiality and runout Coaxiality

Deviations from coaxiality, i.e. the difference
Deviation from coaxiality and dynamic runout of between the centre lines of the shaft and hous-
the shaft are two of many operating parameters ing bore (shaft-to-bore misalignment, STBM),
that affect seal performance and service life. cause force to be distributed irregularly on the
They should therefore be kept within narrow sealing lip († fig. 7). This means that one sec-
limits, particularly when there is a pressure dif- tion of the sealing lip will be subjected to more
ferential across the seal. The total deviation force, causing an enlargement of the contact
should never exceed 1,3 times the value of the area between lip and counterface surface, 2
permissible deviation from coaxiality. whereas the opposite section will be correspond
ingly unloaded and its sealing effect reduced.
Guideline values for the permissible coaxiality
deviations for SKF seals can be obtained from
diagram 3 on page 60.
Fig. 7
Coaxiality
Radial shaft seals
Diagram 3
Maximum permissible deviation from coaxiality as a function of shaft diameter
Coaxiality deviation [mm (in.)] Shaft diameter [mm (in.)]

0 200 600 1 000 1 400 1 800 2 200 2 600 4 570
(7.874) (23.622) (39.370) (55.118) (70.866) (86.614) (102.362) (179.921)
1,6
(0.063)
1,5
(0.059) HDS and HS seals
1,4
(0.055)
1,3
(0.051)
1,2
(0.047)
1,1
(0.043)
1,0
(0.039)
0,9
(0.035)
0,8
(0.031)
Coaxiality deviation [mm (in.)]
0,5
(0.020)
0,4
(0.016)
0,3
(0.012) CRS, CRW1 and HMS5 and HMSA10 seals
0,2
(0.008)
0,1
(0.004) CRW5 seals
0
0 20 60 100 140 180 220 260 440
(0.787) (2.362) (3.937) (5.512) (7.087) (8.661) (10.236) (17.323)
Shaft diameter [mm (in.)]
Runout
Runout (or dynamic runout, DRO) describes the
dynamic eccentricity of the shaft. Particularly at
high speeds, there is a risk that the sealing lip,
because of its inertia, will not be able to follow
the shaft surface († fig. 8). If the eccentricity
is such that the distance between the sealing lip
and shaft becomes larger than that required to
maintain a hydrodynamic lubricant film, the 2
medium to be sealed will escape through the
gap. It is therefore advisable to arrange the seal
in close proximity to the bearing and to keep
bearing operating clearance to a minimum.
Permissible runout values can be obtained
from diagram 4 on page 62. These values are
normally lower for narrow seals.
Fig. 8
Runout
Radial shaft seals
Diagram 4
Maximum permissible runout as a function of rotational speed
Runout [mm (in.)] Rotational speed [r/min]

0 1 000 2 000 3 000 4 000 5 000 6 000 7 000
1,1
(0.043)
1,0
(0.039)
0,9
(0.035)
HDS and HS seals

0,8
(0.031)
0,7
(0.028)
Runout [mm (in.)]
0,4
(0.016)
0,3
(0.012)
0,2
(0.008) CRS, CRW1 and HMS5 and HMSA10 seals
0,1
(0.004)
CRW5 seals
0
0 1 000 2 000 3 000 4 000 5 000 6 000 7 000
Rotational speed [r/min]
Axial movement
Small movements of the shaft relative to the
housing in the axial direction do not affect seal
performance, provided that the total counter-
face surface meets the same demands relative
to hardness, accuracy and surface finish.
2
Permissible speeds
Guideline values for the permissible rotational
and circumferential speeds for different seal
designs are provided in the seal selection charts
(matrix 2 on pages 198 to 201). If the circum-
ferential speeds provided in the matrix are not
sufficient for a particular sealing position,
diagram 5 from DIN 3760 on page 64 may be
used. The diagram lists circumferential and ro-
tational speeds related to the material of the
sealing lip. The values are valid for spring-loaded
sealing lips that are well-lubricated by a mineral
oil, where adequate lubricant supply prevents
heat build-up and where the pressure is the
same on both sides of the seal (pressure differ-
ential = 0).
Diagram 5 shows that large diameter shafts
can accommodate higher circumferential speeds
than shafts with smaller diameters. This is be-
cause the cross section of the shaft does not in-
crease linearly with the increase in diameter but
by the square of the increase in diameter. There-
fore, the heat dissipation of a large shaft is much
better than that of a small shaft.
Generally, SKF Wave seals can be operated at
higher circumferential speeds than those obtained
from diagram 5 because of the hydrodynamic
form of the lip.
The values obtained from diagram 5 should
be reduced if:
• radial shaft seals with an auxiliary, contacting

lip are used
• lubrication is inadequate or grease lubrication
is used, i.e. when underlip temperatures in-
crease due to poor heat dissipation
• the counterface does not meet surface finish
or running accuracy requirements
• there is a pressure differential across the seal
Radial shaft seals
Diagram 5
Permissible speeds for spring-loaded sealing lips where no pressure differential exists across seal in operation
For permissible speeds for seals at shaft diameters > 200 mm, refer to seal selection chart starting on page 92.
Circumferential speed [m/s (ft/min)] Rotational speed [1 000 r/min]

15,0 10,0 9,0 8,0 7,0 6,0 5,0 4,5 4,0
40
(7 874)
Fluoro rubber
3,5
35
(6 890)
3,0
30
(5 906)
2,5
25
(4 921)
2,0
20
(3 937)
15 1,5
(2 953)
Nitrile rubber
10 1,0
(1 969)
5 0,5
(984)
0
0 20 40 60 80 100 120 140 160 180 200
(0.787) (1.575) (2.362) (3.150) (3.937) (4.724) (5.512) (6.299) (7.087) (7.874)
Source: DIN standard 3760
Lubrication Lubrication of paired arrangements

When two radial shaft seals are installed back-
For a radial shaft seal to seal efficiently over a to-back or in tandem, the space between the
long period, the sealing lip must be lubricated. seals should be filled with a suitable lubricant to
This reduces friction and wear to the sealing lip eliminate the risk of the sealing lip running dry.
and shaft. Dry running of sealing lips made of To further prevent dry running, a spacing
standard materials should always be avoided. washer between the seals can also be used. This
To prevent dry running, coat the counterface spacing washer should be provided with lubri
surface with a suitable lubricant prior to seal cation holes or an annular groove and lubrication 2
installation. holes so that grease can be supplied to the space
The lubricant must not only lubricate the between the seals via a grease fitting († fig. 9).
sealing lip to reduce friction and wear, but also
dissipate heat generated by the seal. To promote
heat dissipation, a sufficient quantity of lubri-
cant must be able to reach the sealing lip from
start-up.
Some rolling bearings, such as angular contact
ball bearings, tapered roller bearings and
spherical roller thrust bearings, as well as gears,
create a pumping action by virtue of their design.
This means that the sealing lip can either be
starved of lubricant, or subjected to excessive
quantities of lubricant. In either case, steps
must be taken during the design stage to make
sure that the proper amount of lubricant reaches
the sealing lip, as too much or too little can affect
seal performance.
To prevent lubricant starvation, lubrication
ducts can be provided. If the seal is subjected
to excessive amounts of lubricant, a flinger can
be installed between the bearing and seal.
In applications where the sealing lip is not
exposed to a lubricant, for example when two
seals are installed in tandem, grease or oil must
be supplied separately to provide lip lubrication.
In some cases, it may be sufficient to provide an
Fig. 9
initial grease fill between the two lips.
Lubrication of a paired arrangement
Radial shaft seals
Friction Diagram 6 provides an indication of the fric-

tion losses that may be expected when a radial
To be effective, the lip of a radial shaft seal must shaft seal with a conventional sealing lip is prop-
always exert a certain radial load on the coun erly installed and fully lubricated.
terface. The friction resulting from this radial The running-in phase of the sealing lip lasts
load is only part of the total contact friction and a few hours. During this time, the friction losses
power loss at the sealing position. Other con are somewhat higher than during normal
tributing factors include: operation.
Seals intended for applications with high
• type of medium being sealed pressure differentials typically have greater
• pressure differential across the seal losses than specified in the diagram. SKF Wave
• circumferential speed seals, on the other hand, typically have losses
• ambient temperature lower than those indicated in the diagram.
• lubricant and lubrication method
• condition of the counterface
Diagram 6
Friction losses of radial shaft seals as a function of rotational speed and shaft diameter
Rotational speed [r/min]

Friction loss [W] 5 000 4 000 3 000
600
500
400 2 000
300
200
1 000
100
500
0
10 20 40 60 80 100 120 140
(0.394) (0.787) (1.575) (2.362) (3.150) (3.937) (4.724) (5.512)
Chemical and thermal

resistance
The most important factor when selecting the
appropriate elastomer for a radial shaft seal is
its chemical resistance to the medium to be
sealed or excluded. The operating temperature
is another important factor. Heat accelerates
ageing of the elastomer and increases the re 2
activity and aggressiveness of the sealed
medium.
Radial shaft seals are mainly used to seal
lubricating oils and greases as well as hydraulic
fluids (including non-flammable fluids). Guide-
line values are provided in table 4 on page 68
for the permissible operating temperatures, i.e.
temperatures at which the SKF seals are still
chemically resistant. The temperature range
stated for a group of media means that the seal-
ing material is resistant when continuously op
erated within this particular range.
The N means that, within the group, there
are some media that are compatible with the
elastomer, but also some that have a detrimental
effect on the elastomer.
The n means that the seal material is not
resistant to media belonging to this group.
For the resistance of seal materials to media
not listed in table 4 on page 68, refer to the
section Chemical resistance († page 35) or
contact SKF.
Radial shaft seals
Table 4
Chemical and thermal resistance, radial shaft seal lip materials
Medium to be sealed Permissible operating temperatures (continuous)

for SKF radial shaft seal lip materials1)
R P S V
(NBR) (ACM) (MVQ) (FKM)
– °C °F °C °F °C °F °C °F
Mineral oil based lubricants

Motor oils 100 210 130 270 150 300 170 340
Gear oils 80 175 120 250 130 250 150 300
Hypoid gear oils 80 175 120 250 n 150 300
Automatic transmission fluids (ATF oils) 100 210 130 270 N 170 340
Greases 90 195 N N N
Hydraulic fluids 90 195 120 250 N 150 300
Fire-resistant hydraulic fluids

Oil in water emulsions and aqueous 70 160 n 60 140 N
polymer solutions
Anhydrous fluids n n n 150 300
Other media
Fuel oils EL and L 90 195 N n N
Water 90 195 n n 100 210
Alkaline washing solutions 90 195 n n 100 210
Permissible temperature range

for sealing lip min: –40 –40 –40 –40 –60 –75 –40 –40
max: +100 +210 +150 +300 +160 +320 +200 +390
n Lip material not resistant

N Lip material not resistant to some media in this group
1) R = nitrile rubber
P = polyacrylate elastomer
S = silicone rubber
V = fluoro rubber
Seals under pressure Fig. 10
Pressure profile seals

When a seal is exposed to pressure, the radial
load of the sealing lip increases. This in turn in-
creases the actual sealing lip/shaft contact area,
resulting in additional friction and elevated un-
derlip temperatures. Therefore, the guideline
values for speeds provided in diagram 5 on
page 64 do not apply. 2
Diagram 7 shows an example of lip distortion CRW5 CRWA5
of a conventional sealing lip design as sump
pressure increases, resulting in reduced seal
Fig. 11
service life.
SKF CRW5 and CRWA5 pressure profile seals CRWA5 seal
(† fig. 10) are designed to withstand pressure
differentials of 0,34 MPa (50 psi) at speeds up
to 5 m/s (1 000 ft/min).
When there is a pressure differential across
the seal, a shoulder or retaining ring should be
used at the low-pressure side of the seal to pre-
vent it from being pressed out of the housing
bore († fig. 11).
Diagram 7
Seals under pressure

Example of conventional sealing lip distortion as sump pressure increases, resulting in reduced seal service life.
Seal service life [hours]

2 500
2 000
1 500
1 000
500
0
O kPa 34,5 kPa 69,0 kPa 103,4 kPa 310,0 kPa
0 psi 5 psi 10 psi 15 psi 45 psi
Radial shaft seals
Shaft requirements Fig. 12
Counterface for radial shaft seals

General
To achieve reliable sealing performance and
maximum service life, the counterface for a
radial shaft seal should meet the requirements
outlined below. The seal counterface must be
able to accommodate all permissible deviations
and movements – surface SL and an additional
surface SL’ – which may be required in the case
of repairs or inspection († fig. 12).
In cases where a shaft cannot be machined to
meet the requirements, SKF recommends the
use of SKF Speedi-Sleeve or a wear sleeve for SL
heavy industrial applications (LDSLV). Detailed
information about sleeves is provided in the
chapter Wear sleeves starting on page 327.
Tolerances
The diameter of the shaft d1 at the counterface
should be machined to the tolerances provided
in table 6 for metric shafts and table 7 for inch-
size shafts.
Out-of-roundness must be less than
0,005 mm (0.0002 in.) at a maximum of 2 lobes SL©
or less than 0,0025 mm (0.0001 in.) at a max SL
imum of 7 lobes.
If components with an interference fit will
pass over the counterface during installation,
the shaft diameter should be reduced by 0,2 mm should be kept within the limits specified in
(0.008 in.). The seal that was originally chosen RMA OS-1-1 († table 5).
can still be used without adversely affecting seal The lower value for Ra is a minimum value.
performance. Using a lower value will adversely affect the
lubricant supply to the sealing lip. The tempera-
ture rise caused by inadequate lubrication, par-
Surface roughness ticularly at high circumferential speeds, can lead
The surface roughness values of the counter- to hardening and cracking of the sealing
e3 lip which
face for radial shaft seals, calculated according will eventually lead to premature
e4 = SL
seal failure. If
to methods described in ISO 4288 (DIN 4768), the counterface is too rough, there will be
Table 5
Recommended shaft surface roughness values
ISO DIN RMA
µm µin. µm µin. µm µin.
Ra 0,2–0,5 8–20 0,2–0,8 8–32 0,2–0,43 8–17
Rz 1,2–3 48–120 1–5 40–200 1,65–2,9 65–115
Rpm N/A N/A N/A N/A 0,5–1,5 20–50
Table 6
Counterface tolerances for metric shafts
Shaft diameter Diameter tolerance (ISO h11)1)

Nominal Deviation
d1
over incl. high low
mm µm
6
10
10
18
0
0
–90
–110
2
18 30 0 –130
30 50 0 –160
50 80 0 –190
80 120 0 –220
120 180 0 –250

180 250 0 –290
250 315 0 –320
315 400 0 –360

400 500 0 –400
500 630 0 –440
630 800 0 –500

800 1 000 0 –560
1 000 1 250 0 –660
1 250 1 600 0 –780

1 600 2 000 0 –920
2 000 2 500 0 –1 100
2 500 3 150 0 –1 350

3 150 4 000 0 –1 650
4 000 5 000 0 –2 000
1) For shaft diameters of 3 150 mm and above, refer to DIN 7172.
Table 7
Counterface tolerances for inch-size shafts
Shaft diameter Diameter tolerance (RMA 0S-4)

Nominal Deviation
d1
over incl. high low
in. in.
– 4 +0.003 –0.003
4 6 +0.004 –0.004
6 10 +0.005 –0.005
10 +0.006 –0.006
Radial shaft seals
excessive sealing lip wear and seal service life Lead-in chamfers
will be shortened. If the value Rpm is exceeded, To install radial shaft seals without damaging
the seal will leak or excessive sealing lip wear the sealing lip, SKF recommends chamfering
may occur. or rounding the shaft ends or shoulders
(† table 8).
If the direction of installation is Z, the values
Surface finish (d1 – d2) provided in table 8 should be adhered
Depending on the direction of rotation, direc- to. If the direction of installation is Y, the shaft
tionality on the seal counterface may cause a end could be either rounded (r) or chamfered
seal to leak. Plunge grinding is the preferred (d1 – d2).
machining method to minimize directionality To install a seal over a shaft shoulder or end
(0±0,05°) on the seal counterface. When plunge that has not been rounded or chamfered, SKF
grinding, whole number ratios of the grinding recommends using an installation sleeve. See
wheel speed to the work piece speed should be section Seal installation, heavy industrial appli-
avoided. Run the grinding wheel until it “sparks cations on page 79.
out” completely, i.e. until there are no more
sparks flying from the wheel, to ensure that all
lead is removed. The grinding wheel should be
dressed using a cluster head dressing tool and
the smallest possible lateral feed, or a profile
dressing roll without lateral feed. The negative
influence of directionality in any particular case
can only be ascertained by test running under
conditions of alternating rotation.
The seal counterface surface should be free
of any damage, scratches, cracks, rust or burrs
and should be properly protected until final
installation.
Hardness and surface treatment

The surface hardness of the seal counterface
should be at least 30 HRC (58 HRC for PTFE lip
seals). If the counterface surface could be dam-
aged during transport or installation, this value
should be increased to 45 HRC (62 HRC for
PTFE lip seals). Under certain conditions, where
speeds are low, lubrication is good and contam-
inants are absent, counterface surfaces having
a lower hardness may be suitable. Surfaces that
are nitrided, phosphated or have a galvanized
coating may also be suitable, but this must be
determined for each specific case.
Table 8
Lead-in chamfers and radii
r Burr-free
15–30°
Y Z
d1 h11 d2
Shaft diameter Diameter Radii

Nominal difference1) Seal without Seal with
auxiliary lip auxiliary lip
d1 d1 – d2 r r
over incl. over incl. min min min
mm in. mm in. mm in. mm in.
– 10 – 0.394 1,5 0.059 0,6 0.024 1 0.039

10 20 0.394 0.787 2 0.079 0,6 0.024 1 0.039
20 30 0.787 1.181 2,5 0.098 0,6 0.024 1 0.039
30 40 1.181 1.575 3 0.118 0,6 0.024 1 0.039

40 50 1.575 1.968 3,5 0.138 0,6 0.024 1 0.039
50 70 1.968 2.756 4 0.157 0,6 0.024 1 0.039
70 95 2.756 3.740 4,5 0.177 0,6 0.024 1 0.039

95 130 3.740 5.118 5,5 0.216 1 0.039 2 0.079
130 240 5.118 9.449 7 0.276 1 0.039 2 0.079
240 500 9.449 19.685 11 0.433 2 0.079 3 0.118

500 – 19.685 – 13 0.512 5 0.197 5 0.197
1) lf
the corner is blended rather than chamfered, the blended section
iameters d1 – d2.
should not be smaller than the difference in d
Radial shaft seals
Housing bore requirements Fig. 13
Housing bore requirements

General
B
To reduce the risk of seal damage during instal-
b
lation, the housing bore should have a 15 to 30°
lead-in chamfer. The chamfer should be free of 15–30°
burrs and the transition radius r between the
seal seat and shoulder should be in accordance
with the recommendations in table 9. A
In order to facilitate seal removal, holes in the
housing shoulder A can be incorporated during D H8
the design stage.
Metal-reinforced seals
The depth of a metric housing bore B for metal-
cased or metal-inserted seals should be at least
0,3 mm (0.012 in.) larger than the nominal seal
width b († fig. 13). The corresponding values
for an inch housing bore B are 0.016 in.
(0,4 mm).
Seals without metal-reinforcement

Seals without metal reinforcement are manu-
factured oversized relative to the housing bore
diameter and depth to enable proper compres
sion and stability. The actual seal width is ap-
proximately 0,4 to 0,8 mm (0.016 to 0.032 in.)
wider than the bore depth B. For all-rubber HS
seals, the bore depth tolerance should be
±0,13 mm (0.005 in.) and ±0,10 mm (0.004 in.)
for all-rubber reinforced HSS seals and fabric-
reinforced HSF seals. For seals without metal
reinforcement, a cover plate is required for a
proper fit († page 82).
Table 9
Housing bore tolerances
15–30°
r
A
2
D H8
Housing bore for metric seals (ISO) Housing bore for inch-size seals (RMA)
Nominal Housing bore tolerance Fillet Nominal Housing bore tolerance Fillet
diameter (ISO tolerance H8) radii diameter radii
D r D r
over incl. high low max over incl. high low max
mm µm mm in. in. in.
– 3 +14 0 0,3 – 3.000 +0.001 –0.001 0.031

3 6 +18 0 0,3 3.000 7.000 +0.0015 –0.0015 0.031
6 10 +22 0 0,3 7.000 10.000 +0.002 –0.002 0.031
10 18 +27 0 0,3 10.0002) 12.000 +0.002 –0.002 0.031

18 30 +33 0 0,3 12.0002) 20.000 +0.003 –0.003 0.031
30 50 +39 0 0,3 20.0002) 40.000 +0.004 –0.004 0.031
50 80 +46 0 0,4 40.0002) 60.000 +0.006 –0.006 0.031

80 120 +54 0 0,8
120 180 +63 0 0,8
180 250 +72 0 0,8

250 315 +81 0 0,8
315 400 +89 0 0,8
400 500 +97 0 0,8

500 630 +110 0 0,8
630 800 +125 0 0,8
800 1 000 +140 0 0,8

1 000 1 250 +165 0 0,8
1 250 1 600 +195 0 0,8
1 600 2 000 +230 0 0,8

2 000 2 500 +280 0 0,8
2 500 3 150 +330 0 0,8
3 1501) 4 000 +410 0 0,8

4 0001) 5 000 +500 0 0,8
1) SKF recommended bore specifications not covered in ISO 286-2

2) SKF recommended bore specifications not covered in RMA OS-4
Radial shaft seals
Tolerances
The housing bore diameter D should be ma-
chined to tolerance H8 († table 9 on page 75).
Depending on the operating conditions, out-of-
roundness should be 1 to 2 tolerance grades
better than H8.
Surface roughness
The surface roughness (to ISO 4288 or
DIN 4768) of the housing bore should be kept
within the limits specified in table 10.
Table 10
Recommended housing bore surface roughness values
ISO1) DIN RMA2)3)
µm µin. µm µin. µm µin.
Ra 1,6–3,2 64–128 1,6–3,2 64–128 1–2,5 40–100
Rz 6,3–12,5 252–500 10–20 400–800 N/A N/A
Rmax N/A N/A 25 1 000 N/A N/A
1) ISO – The housing bore surface roughness may require lower values when metal-cased seals are used, in which case they
should be subject to agreement between the manufacturer and user.
2) RMA – If the bore surface texture is greater than 2,5 µm (100 µin.) Ra, a sealant should be used.
3) RMA – Turned bores, where a lubricant head of up to 0,20 bar (3.0 psi) is present at the seal. If this texture is maintained
and tool removal marks or bore defects are not present, no outside diameter leakage should occur.
Seal installation, general Fig. 14
industrial applications Preferred installation method
General
To provide effective sealing, radial shaft seals
must be installed properly. An experienced in-
staller with suitable tools, working in a clean en-
vironment, is recommended to provide proper D di 2
installation. The shaft counterface surface and
housing bore should meet the demands speci-
fied under Shaft requirements and Housing bore
requirements on pages 70 to76.
To facilitate seal installation and to achieve
initial lubrication, prior to installation, SKF
recommends wiping the shaft and seal with di ≈ D – 6 mm
the lubricant that is going to be retained. While
the outside diameter of metal-cased seals can
Fig. 15
be lightly lubricated to ease installation, the out-
side diameter of rubber covered seals should Alternative installation method
always be lubricated.
Seals with an auxiliary, contacting lip can also d3
be filled with grease between the sealing lip and d7
auxiliary lip to reduce frictional moment. This
does not apply to silicone rubber seals and seals
with hydrodynamic features, other than SKF
Wave lip designs.
SKF also recommends using a hydraulic
press, with suitable tools, to install a seal in its
housing bore. Pressure should be applied as
close as possible to the outside diameter of the
seal.
Seals that are designed to sit flush with the d7 = d3 – 0,5 mm
wall of the housing bore must be installed per-
pendicular to the housing bore axis. The outside
diameter of the tool should be larger than the
Fig. 16
housing bore diameter († fig. 14).
When pressing seals up against a shoulder or Alternative installation method
retaining ring, it is advisable to use tools of the
type shown in figs. 15 and 16. The necessary D
ring dimensions can be supplied on request. d7
d7 = D – 0,5 mm
Radial shaft seals
Fig. 17
When installing seals on stepped shafts,
Installation sleeve where the shoulders do not have the recom-
mended chamfer or rounded transition, an in-
stallation sleeve as shown in fig. 17 must be
used. If the sealing lip has to pass over grooves,
threads or gearing, thin-walled installation
sleeves, like those shown in fig. 18, can be used
to prevent the lip from being damaged. The out-
side surface of the sleeve should be coated with
the same lubricant that is used to lubricate the
seal and counterface surface.
Radial shaft seals made of silicone rubber
should always be installed using an installation
sleeve.
The tools used to install a seal at a certain
distance in a cylindrical opening in a housing
are shown in figs. 19 and 20. Instructions for
designing the tools can be supplied on request.
Fig. 18
Thin-walled installation sleeve
Fig. 19 Fig. 20
Installation in a cylindrical opening Installation in a cylindrical opening
d3
d7
d7 = d3 – 0,5 mm
Seal installation, heavy Fig. 21
industrial applications Use a dead blow hammer
Metal-reinforced seals 6
3
7
When installing metal-reinforced seals, the first
step is to check the shaft and housing bore for 1 2
proper specifications and condition. Next, coat
both the seal and bore lightly with a lubricant, 8 5 2
preferably the same one that will be used to 4
lubricate the application. For large diameter
seals, a special installation tool may not be prac-
tical. In these cases, do not hit the seal or seal
case directly. Instead, use a wooden block, long
enough to span the seal’s outside diameter.
When using this method, it is important to apply
hammer-blows evenly and sequentially to the
wood piece around the seal circumference to
prevent the seal from tilting or skewing. SKF also
recommends the use of a dead blow hammer for
full energy transfer with less impact († fig. 21).
In some applications, the housing is designed
for two seals in tandem, or a seal might have to
be recessed further into the bore depth. In those
cases, first set the seal flush with the housing
using the method described above. Then, use
a shorter piece of wood to drive the seal deeper
into the bore utilizing a sequential pattern
(† fig. 22).
Fig. 22
Installation deeper into the bore
5 3 8
2 1
7 4 6
Radial shaft seals
Seals without metal reinforcement brought together and allowed to thread into
Be sure that the shaft surface and housing bore each other. When using a hook-and-eye con-
are clean and that they meet the specifications nector, draw the ends of the spring together and
listed in Shaft requirements and Housing bore insert the hook into the eye, taking care not to
requirements on pages 70 to 76. Special care over-stretch the spring in the process, as this
must be taken to avoid nicks and burrs on the might impair seal performance. When using
shaft and to make sure that the spring is retained a control-wire connector, draw the seal ends
in the spring groove. together and insert the control wire into the
HS seals are installed differently depending centre of the spring coil.
on whether their main purpose in a specific Position the seal joint on the shaft so that it is
application is to retain lubricant or to exclude at the 12 o’clock position and push both ends of
contaminants († fig. 23). the joint into the housing bore (D). Do not push
only one joint and then work around the shaft
as this will create an excess length, making
Split seals installation difficult or impossible.
Where appropriate, insert the spring in the SKF Continue at the 3 and 9 o’clock positions, push
Springlock groove and position the spring con- the rest of the seal into position (E) and finish
nection, so that it is displaced with regard to the simultaneously at the 6 and 12 o’clock positions.
seal joint († A in fig. 24). This is standard with For shaft diameters ≥ 1 200 mm (47 in.), it is
all HS8 seals. Put the seal in the correct position advisable to fix the seal at the 12, 3, 6 and
on the shaft. 9 o’clock positions before locating the remaining
Lightly coat both the seal and counterface sections of the seal.
surface with a lubricant, preferably the same Use a small block of wood to push the seal in
lubricant that will be used to lubricate the appli the housing bore until it contacts the housing
cation (B). shoulder (E).
Join the ends of the garter spring by using the Check the seal condition, particularly at the
spring connector (C). joint, to make sure that it has been positioned
For threaded connectors, back-wind the properly.
spring a couple of turns before the ends are Install the cover plate (see paragraph Cover
plates on page 82) on the housing face. Tighten
Fig. 23
the bolts evenly until the end cover abuts the
Ways of installing HS seals housing face (F and G).
HS seal installed to retain

lubricant
HS seal installed to exclude

foreign material
HS seals in tandem
arrangement for maximum
lubricant retention
Fig. 24
Installing a split seal
A E
D G
Radial shaft seals
Cover plates In applications where supplementary sealing

Seals without metal reinforcement, split and is necessary, and it is impractical to machine the
solid, are manufactured oversized relative to original housing to provide a seal cavity, a seal
the housing bore diameter and depth to enable cavity can be incorporated into a new plate that
proper compression and stability. A cover plate is bolted into place as illustrated in fig. 26.
(† fig. 25) provides axial compression of the
seal and stabilizes it in the housing bore to
achieve maximum seal performance. The cover
plate must be dimensioned properly to obtain
the required fit. It should be thick enough not to
bend or distort. Generally, a thickness of 6,35 to
12,7 mm (0.25 to 0.50 in.) is sufficient.
The plate should be fastened with bolts, no
more than 150 mm (6 in.) apart, on a bolt circle
located as close to the seal housing bore as
practical. The cover plate should be flat and the
housing bore depth uniform. Splitting the cover
plate at 180° will make seal replacement easier,
particularly in confined areas.
To block surges of lubricant toward the seal
from the inside and to protect the seal from
damage from the outside, SKF recommends
dimensioning the inside diameter of the cover
plate so that it is 6 to 8 mm (0.25 to 0.30 in.)
greater than the shaft diameter to accommo-
date shaft-to-bore misalignment and runout
(† fig. 25).
Fig. 25
Cover plate recommendations
P D D1 d1
Inside diameter of cover: D1 ≈ d1 + 6 .. 8 [mm]

Pitch circle diameter of screws: P ≈ 1,1 D [mm]
No. of attachment screws: N ≈ 0,02 P
Multiple HS seal installations Fig. 26
When installing two split all-rubber HS seals in Cover plate

one cavity, the locations of the split joints should
be staggered by 30° to 60° to minimize the risk New seal cavity plate
of leakage through the joints. The splits should
be located toward the top of the bore. Grease
the cavity between the seals to provide lubricant Seal-retaining
cover plate
to the outer sealing lip.
When two HS seals, split or solid, are installed Sealing element 2
in the same housing bore, a spacing washer must
be placed between the two seals († fig. 27).
Suitable washer dimensions can be determined
based on the shaft and housing bore diameters,
d1 and D, respectively: 6,35 – 12,7 mm
washer inside diameter

= d1 + 6 to 10 mm (0.25 to 0.4 in.)
Fig. 27
washer outside diameter
= D – 0,5 to 1,5 mm (0.02 to 0.06 in.) Spacing washer
The width of the washer is determined by the

application conditions. There should, however,
always be sufficient room for lubrication holes
to be provided in the circumference, or lubrica-
tion grooves in one side face († fig. 28). These
lubrication provisions must enable grease to be
supplied from the housing to the sealing lips via
a drilled passage or grease fitting († fig. 29 on
page 84). When determining what washer width
is appropriate for the depth of a housing bore, it
is necessary to consider the axial displacement
required when clamping the seals.
Fig. 28
Details of spacing washer for central lubrication

A separator between two seals can be a slotted washer to promote distribution of the lubricant.
d1 + 6,4 mm D – 0,5/1,5 mm
(d1 + 0.25 in.) (D – 0.06 in.)
Radial shaft seals
Multiple HDS seal installations

When installing two metal-cased radial shaft
seals in the same housing bore, either in a tan-
dem or back-to-back arrangement, care must
be taken that neither of the sealing lips can run
dry at any time. To reduce the risk of dry running,
the space between the seals should be filled with
a suitable grease.
To avoid dry running, SKF recommends using
spacer lugs or a spacing washer between the
two seals. The spacing washer should be pro-
vided with lubrication holes so that grease can
be supplied to the space between the sealing
lips via a grease fitting († fig. 29). No spacing
washer is required when using seals that have
spacer lugs built into the air side of the metal
case († fig. 30). HDSD and HDSE seals can be
supplied from SKF with holes pre-drilled in the
metal case to mate with corresponding passages
in the housing bore.
Fig. 29 Fig. 30
Spacing washer and grease fitting Spacer lug
PTFE seals
In most cases, small diameter PTFE seals are
shipped on a tube that maintains a nominal seal
inside diameter (smaller than shaft diameter)
during storage. Therefore, they should not be
removed from the shipping tube until immedi-
ately prior to installation. Also, if quality inspec-
tions must be done, SKF recommends that the
shipping tube remains in place. The seal inside 2
diameter cannot be accurately measured anyway
after manufacturing as the PTFE lip configuration
changes over time as it relaxes.
PTFE formulations used for radial lip seals are
generally more aggressive and abrasive to the
shaft than standard elastomeric materials.
Therefore, PTFE sealing lips require a surface
hardness value of 58 to 62 HRC. An alternative
to a hardened shaft surface is the use of an SKF
wear sleeve, manufactured to the same high
standards such as the inner rings of SKF needle
roller bearings, offering an excellent sealing
surface.
In applications where PTFE seals will be re-
taining a lubricant or be fully flooded with a fluid,
the seals should be installed dry. In applications
that run dry or will be starved for lubrication, the
sealing lip should be pre-lubricated with a grease
appropriate for the temperature conditions of
the application.
WARNING: At temperatures above 300 °C
(570 °F), all PTFE compounds give off danger-
ous fumes. For additional information, refer to
page 32.
Radial shaft seals
Installation procedure installation cones if detailed drawings of the

PTFE lips do not have the same elastic prop shaft and sealing areas are provided. In lieu of
erties as rubber lips, which makes them more installation cones, longer than normal lead-in
susceptible to damage. Therefore, special care chamfers on the shaft would be required. How-
must be taken during installation and handling ever, shaft features that could damage the seal
to prevent damage and help ensure proper (keyways, etc.) must still be covered, possibly
operation and function. Shaft features such as with tape.
keyways and splines, as well as drill holes, ports If the shaft is installed with the PTFE lip, a
and sharp-edged shaft steps have the potential smooth, burr-free radius or chamfer on the
to damage PTFE lips. Whenever possible, these shaft end is all that is required, provided that no
obstructions can be covered by using thin-walled damaging shaft features are present as noted
installation tools made from plastic or metal. above († fig. 31, b and d).
PTFE lip orientation during installation will Some seals have two PTFE lips facing oppos
determine the installation method. Installation ite directions. In this case, installation is always
is more difficult when the shaft is installed against one of the lips and an installation cone is
against the PTFE lip († fig. 31, a and c). This recommended.
type of installation becomes even more compli-
cated when the hardware is difficult to access or
visually obstructed and may not be possible if
an installation tool cannot be used. In any case,
when the shaft is installed against the PTFE lip,
SKF recommends the use of an installation cone
or “bullet”. SKF can quote and manufacture
Fig. 31
Seals with a PTFE sealing lip
shipping tube installation shipping tube

cone
lead-in
chamfer
a) Installation against the PTFE lip b) Installation with the PTFE lip
Seals with an elastomeric sealing lip and a PTFE auxilary lip
elastomeric
sealing lip
PTFE installation
auxiliary lip cone
lead-in
chamfer
c) Installation against the PTFE lip d) Installation with the PTFE lip
Protecting the counterface Replacement

surface against corrosion The lip of the replacement seal should not run
The seal counterface surface should be protected on the same path as the lip of the old seal. There
from corrosion until the machine is operational. are several ways to achieve this:
Be sure to use a rust inhibitor that will last for a
year, whether or not the shaft is exposed. • Install SKF Speedi-Sleeve, see page 327.
The protective coating should be soluble in • Rework or replace the counterface (this may
the medium to be retained and must not cause entail removing the shaft). 2
any chemical separation as this can impair the • Install a spacing ring in the housing bore
sealing performance. between the housing shoulder and the seal
When machines are transported, stored under († fig. 32).
unfavourable conditions, or out of service for • Press the new seal to a different depth in
extended periods, special rust inhibitors should a cylindrical opening in the housing, i.e.
be used. These rust inhibitors should form a toward the medium to be sealed.
tough, pliable waxy film that can be removed
using neutral solvents that leave an oily residue. When choosing a replacement seal, be sure
that its design and material correspond to the
original seal. In case of doubt, select a seal that
Removal meets the operating conditions of the applica-
tion, and that the seal materials are compatible
Because radial shaft seals should never be re- with the lubricant.
used, there is no need to worry about damaging Seals made from a different material should
the seal when removing it. However, prior to only be used when absolutely necessary. In
removal, it is advisable to note the direction in these cases, the recommendations provided in
which the seal is installed so that the replace- table 11 should be followed. The order in which
ment seal can be installed in the same direction. the materials are listed is an indication of their
Small seals can generally be removed using a suitability.
screwdriver, taking care not to damage the shaft If a seal of the same design is not available in
surface. The removal of large-size seals is made the same width as the original, then a some-
easier if holes have been provided in the housing what narrower seal can be used, or if the depth
shoulder A, see picture in table 9, page 75, of the housing bore allows, a somewhat wider
allowing access for a drift. seal can be selected as the replacement.
Fig. 32 Table 11
Spacing ring Replacement sealing lip materials
Original Replacement
Felt Nitrile rubber

Fluoro rubber
Leather Nitrile rubber

Fluoro rubber
Nitrile rubber Polyacrylate elastomer

Fluoro rubber
Silicone rubber
Polyacrylate elastomer Fluoro rubber

Silicone rubber
Silicone rubber Fluoro rubber
Radial shaft seals
Designation system Assortment and availability

Metric radial shaft seals The SKF assortment of radial shaft seals
Designations of all SKF metric radial shaft seals comprises some 200 designs and executions for
specify shaft diameter, housing bore diameter applications within basically all industries. The
and nominal seal width (bore depth for HSF and radial shaft seals described in this publication
HS seals) in millimetres, followed by design and belong to the standard range and most of them
the code of the sealing lip material († table 12). are available in both metric and inch sizes. New
seal designs and sizes are continually added. For
additional information, contact SKF.
Inch-size radial shaft seals
Inch-size SKF radial shaft seals are identified by
their stock number that consists of four to seven
digits. The stock number provides an indication
of seal size.
Four-figure numbers are used for radial shaft

seals for
shaft diameters: d1 ≤ 1 in., e.g.

3680 d1= 0.375 in.
Five-figure numbers are used for radial shaft

seals for
shaft diameters: d1 ≤ 10 in., e.g.

41287 d1 = 4.125 in.
97545 d1 = 9.750 in.
Six- and seven-figure numbers are used for

radial shaft seals for
shaft diameters: d1 ≥ 10 in., e.g.

120061 d1 = 12 in.
1375242 d1 = 13.75 in.
Table 12
Designation system for metric radial shaft seals
55 ¥ 72 ¥ 8 HMSA10 RG 1
Dimensions
2
55 Shaft diameter
72 Housing bore diameter
8 Nominal seal width (bore depth for HSF and HS seals)
Design
HMSA10
Lip material
RG Acrylonitrile-butadiene rubber, SKF developed, used for the HMS5 and HMSA10 seals
Execution
1, 2 … Seals of the same size and design that differ in execution from
the basic design are identified by a number e.g. R1
Radial shaft seals
Seals for general industrial applications, selected main designs
RG, R Nitrile rubber

V Fluoro rubber
T Polytetrafluoroethylene (PTFE)
Seal designs Design

Outside diameter Sealing lip Auxiliary lip
Configuration Material Configuration Material A = Contacting
code code B = Non-contacting
Rubber RG, V Straight RG B (HMSA10)

V
HMS5 HMSA10
Metal N/A SKF Wave R N/A

V
CRW1 CRWH1
Metal N/A SKF Wave R B

V
CRWA1 CRWHA1
Metal N/A SKF Wave R A (CRWA5)

V
CRW5 CRWA5
Metal N/A Straight R N/A

V
CRS1 CRSH1
Metal N/A Straight R A

V
CRSA1 CRSHA1
Metal N/A Straight R N/A

V
HM14
Rubber R Special R N/A
X15
Metal N/A Special T N/A
SL SLX SLS
Metal N/A Special T A (SLA, DLA)
SLA DL DLA
Fluoroplastic/ T (+ R, V) Special T N/A

(rubber)
YSLE YNSLE YSL
* PTFE designs are made to order to handle temperatures, pressures and speeds that may exceed those stated for rubber sealing lip designs.
Matrix 1
Operating temperature range Shaft-to-bore mis- Dynamic runout Pressure differential Maximum shaft
alignment (STBM) TIR (DRO) TIR surface speed
from to from to
2
°C °F mm in. mm in. MPa psi m/s ft/min
–40 100 –40 210 0,38 0.015 0,51 0.020 0,05 7 14 2 755
–40 200 –40 390
–40 100 –40 210 0,38 0.015 0,51 0.020 0,07 10 18 3 600
–40 200 –40 390
–40 100 –40 210 0,38 0.015 0,51 0.020 0,07 10 18 3 600
–40 200 –40 390
–40 100 –40 210 0,13 0.005 0,13 0.005 0,35 50 10 2 000
–40 200 –40 390
–40 100 –40 210 0,38 0.015 0,51 0.020 0,07 10 18 3 600
–40 200 –40 390
–40 100 –40 210 0,38 0.015 0,51 0.020 0,07 10 18 3 600
–40 200 –40 390
–40 100 –40 210 0,13 0.005 0,08 0.003 0,07 10 10 2 000
–40 200 –40 390
–40 100 –40 210 0,38 0.015 0,25 0.010 0,02 3 2,54 500
–70 250 –95 480 * * * * * * * *
–70 250 –95 480 * * * * * * * *
–70 250 –95 480 * * * * * * * *
Radial shaft seals
Seals for general industrial

applications
HMS5
HMS5 and HMSA10 seals
Main features
SKF metric rubber outside diameter radial shaft
seals, HMS5 and HMSA10, are designed in ac-
cordance with ISO 6194-1 and DIN 3760 for HMSA10
use in a wide range of industrial applications.
The available size range of HMS5 and HMSA10
seals includes a full coverage of the ISO 6194-1 Material
and DIN 3760 dimensions for shaft diameters The optimized nitrile rubber compound used
up to 250 mm (9.842 in.) as well as an extensive for the HMS5 and HSMA10 seals has the desig
range of dimensions commonly used in the nation suffix RG. The compound is the result of
market. New dimensions are continually added. long experience and the latest findings from the
Main features include: SKF seal material developments. Advantages of
this material include:
• optimized sealing lip material
• spring-loaded sealing lip • good resistance to ageing
• optimally balanced sealing lip and flex section • very good compatibility with synthetic oils
• beaded outside diameter • very good pumping ability
• auxiliary lip (HMSA10 seals only) • good wear resistance
Pumping ability is defined as the time it takes

Design for the seal to return a certain amount of oil from
The rubber outside diameter provides optimized the air side to the oil side. The microstructure of
sealing ability in the housing, also at consider- SKF’s RG nitrile rubber compound promotes
able surface roughness or in split housings. The rapid pumping of the oil, († table 13). In
beads on the outside diameter provide improved diagram 8, results from endurance tests show
sealing ability and retention in the bore. They the extended service life of seals made of the
also prevent spring-back during installation. optimized nitrile compound.
The spring-loaded sealing lip contributes to a The complete range of HMS5 and HMSA10
quick response in handling dynamic runout and seals is also available in a fluoro rubber com-
maintaining the sealing performance, even pound with a stainless steel garter spring. This
when sealing lip wear is excessive. rubber compound has the designation suffix V
Sealing lip and flex section are optimally bal- and is used in applications where temperatures
anced to withstand both high dynamic runout exceed the limits of nitrile rubber.
and shaft-to-bore misalignment.
The auxiliary lip on HMSA10 seals is non-
contacting, which means that the seals normally
can operate at the same speeds as the single-lip
HMS5 seals.
Applications and operating conditions Table 13
HMS5 and HMSA10 seals are designed for oil or Speed Pumping time
grease lubricated applications with operating Rotating Circum Standard NBR SKF compound RG
ferential
temperatures ranging from –40 to +100 °C
(–40 to +210 °F), short-term up to 120 °C r/min m/s s
(250 °F). These seals are also appropriate for

sealing lubricants within a wide range of 1 000 3,1 – 117
1 500 4,7 280 69
viscosities. 2 000 6,3 186 50
2 500 7,9 130 40

2
Circumferential speed: up to 14 m/s 3 000 9,4 102 31
(2 755 ft/min) 3 500 11,0 82 25
Operating pressure: max 0,05 MPa (7 psi) 4 000 12,6 68 21
4 500 14,1 57 18
These values are the maximum value for each
service condition and should not occur together.
Consideration should be given as to how the Shaft diameter 60 mm, engine oil SAE 30
operating conditions affect each other. For infor-
mation on seals under pressure, see page 69.
Diagram 8
Average seal life

(as a percentage of baseline, product A)
500
400
300
200
100
0
Product A Product B Product C
Standard NBR High-perform- Standard SKF
compound ance NBR compound RG
compound
Radial shaft seals – HMS5 and HMSA10

d1 6 – 25 mm
1) Designation to be followed by the design and material codes,
indicating one of the four variants available for each dimension:
b
HMS5 RG without auxiliary lip, nitrile rubber
HMS5 V without auxiliary lip, fluoro rubber
HMSA10 RG with auxiliary lip, nitrile rubber
HMSA10 V with auxiliary lip, fluoro rubber
Example: 6¥16¥5 HMSA10 RG
2) Design execution differs from the basic design and is indicated
by a number, see also page 89.
d1 D
Please see pages 74 to 76 for housing bore requirements.
Dimensions Designation1) ISO/DIN Dimensions Designation1) ISO/DIN

Shaft Bore Nominal Shaft Bore Nominal
seal width seal width
d1 D b d1 D b
mm – – mm – –
6 16 5 6¥16¥5 12 28 7 12¥28¥7
16 7 6¥16¥7 • cont.
30 7 12¥30¥7 •
22 7 6¥22¥7 •
32 7 12¥32¥7
7 16 7 7¥16¥72)
37 7 12¥37¥7
22 7 7¥22¥7 •
13 26 7 13¥26¥7
8 18 5 8¥18¥5
18 7 8¥18¥7 14 24 7 14¥24¥7 •
22 7 8¥22¥7 • 25 5 14¥25¥5
24 7 8¥24¥7 • 28 7 14¥28¥7
9 22 7 9¥22¥7 • 30 7 14¥30¥7 •
10 19 7 10¥19¥72) 15 24 7 15¥24¥72)
20 6 10¥20¥6 25 5 15¥25¥5
20 7 10¥20¥7 25 6 15¥25¥6
22 7 10¥22¥7 • 26 7 15¥26¥7 •
24 7 10¥24¥7 30 7 15¥30¥7 •
25 7 10¥25¥7 • 32 7 15¥32¥7
26 7 10¥26¥7 • 35 7 15¥35¥7 •
30 7 10¥30¥7 40 7 15¥40¥7
40 10 15¥40¥10
12 19 5 12¥19¥52)
16 24 7 16¥24¥72)
22 5 12¥22¥5
22 6 12¥22¥6 28 7 16¥28¥7
22 7 12¥22¥7 •
30 7 16¥30¥7 •
24 7 12¥24¥7 •
32 7 16¥32¥7
25 7 12¥25¥7 •

d1 D b d1 D b
mm – – mm – –
16 35 7 16¥35¥7 • 21 35 7 21¥35¥7
cont.
17 28 7 17¥28¥7 40 7 21¥40¥7 2.1
29 5 17¥29¥5 22 32 7 22¥32¥7
30 7 17¥30¥7 35 7 22¥35¥7 •
32 7 17¥32¥7 36 7 22¥36¥7
35 7 17¥35¥7 38 8 22¥38¥8
37 7 17¥37¥7 40 7 22¥40¥7 •
40 10 22¥40¥10
40 7 17¥40¥7
40 10 17¥40¥10 42 10 22¥42¥10
47 7 17¥47¥7 45 7 22¥45¥7
47 10 17¥47¥10 47 7 22¥47¥7 •
18 28 7 18¥28¥7 23 40 10 23¥40¥10
30 6 18¥30¥6 24 35 7 24¥35¥7
30 7 18¥30¥7 •
37 7 24¥37¥7
32 7 18¥32¥7
40 7 24¥40¥7
35 7 18¥35¥7 •
42 8 24¥42¥8
40 7 18¥40¥7
47 7 24¥47¥7
19 30 7 19¥30¥7
30 8 19¥30¥8 50 10 24¥50¥10
32 7 19¥32¥7 25 35 6 25¥35¥6
35 7 25¥35¥7 •
42 6 19¥42¥6
37 5 25¥37¥5
20 30 5 20¥30¥5 37 6 25¥37¥6
30 7 20¥30¥7 • 37 7 25¥37¥7
32 6 20¥32¥6 38 7 25¥38¥7
32 7 20¥32¥7
40 5 25¥40¥5
34 7 20¥34¥7 40 7 25¥40¥7 •
40 8 25¥40¥8
35 6 20¥35¥6 40 10 25¥40¥10
35 7 20¥35¥7 •
35 8 20¥35¥8 42 6 25¥42¥6
35 10 20¥35¥10 42 7 25¥42¥7
42 10 25¥42¥10
36 7 20¥36¥7
25 45 7 25¥45¥7
38 7 20¥38¥7 45 8 25¥45¥8
45 10 25¥45¥10
40 7 20¥40¥7 •
40 10 20¥40¥10 46 7 25¥46¥7
42 7 20¥42¥7 47 7 25¥47¥7 •
42 10 20¥42¥10 47 10 25¥47¥10
45 7 20¥45¥7 50 10 25¥50¥10
47 7 20¥47¥7 52 7 25¥52¥7 •
47 10 20¥47¥10 52 8 25¥52¥8
52 10 25¥52¥10
52 7 20¥52¥7
52 10 20¥52¥10

d1 25 – 40 mm
b
d1 D

d1 D b d1 D b
mm – – mm – –
25 62 7 25¥62¥7 30 40 7 30¥40¥7 •
cont. 62 8 25¥62¥8
62 10 25¥62¥10 42 6 30¥42¥6
42 7 30¥42¥7 •
72 7 25¥72¥7 42 8 30¥42¥8
26 37 7 26¥37¥7 44 7 30¥44¥7
38 5 26¥38¥5 45 7 30¥45¥7
38 7 26¥38¥7 45 8 30¥45¥8
42 7 26¥42¥7 46 7 30¥46¥7
47 7 26¥47¥7 47 6 30¥47¥6
47 7 30¥47¥7 •
27 37 7 27¥37¥7 47 8 30¥47¥8
47 10 30¥47¥10
42 10 27¥42¥10
48 8 30¥48¥8
43 7 27¥43¥7
50 5 30¥50¥5
47 7 27¥47¥7 50 7 30¥50¥7
47 10 27¥47¥10 50 8 30¥50¥8
50 10 30¥50¥10
28 38 7 28¥38¥7
38 8 28¥38¥8 30 52 7 30¥52¥7 •
52 8 30¥52¥8
40 7 28¥40¥7 • 52 10 30¥52¥10
40 8 28¥40¥8
55 7 30¥55¥7
42 7 28¥42¥7 55 10 30¥55¥10
42 8 28¥42¥8
62 7 30¥62¥7
44 6 28¥44¥6 62 10 30¥62¥10
45 8 28¥45¥8 72 10 30¥72¥10
47 7 28¥47¥7 • 32 42 7 32¥42¥7
47 10 28¥47¥10
43 7 32¥43¥7
52 7 28¥52¥7 •
52 10 28¥52¥10 44 7 32¥44¥7

d1 D b d1 D b
mm – – mm – –
32 45 7 32¥45¥7 • 35 72 7 35¥72¥7
cont. 45 8 32¥45¥8 • cont. 72 10 35¥72¥10
47 6 32¥47¥6
72 12 35¥72¥12 2.1
47 7 32¥47¥7 • 80 12 35¥80¥12
47 8 32¥47¥8 •
47 10 32¥47¥10 36 47 7 36¥47¥7
48 8 32¥48¥8 50 7 36¥50¥7
50 8 32¥50¥8 52 7 36¥52¥7
50 10 32¥50¥10
58 10 36¥58¥10
52 7 32¥52¥7 •
52 8 32¥52¥8 • 62 7 36¥62¥7
55 10 32¥55¥10 37 50 6 37¥50¥6
62 10 32¥62¥10 38 50 7 38¥50¥7
72 7 32¥72¥7 52 7 38¥52¥7
52 8 38¥52¥8
80 7 32¥80¥7
38 54 10 38¥54¥10
33 45 7 33¥45¥7
55 7 38¥55¥7 •
50 6 33¥50¥6 55 8 38¥55¥8 •
55 10 38¥55¥10
34 44 8 34¥44¥8
58 8 38¥58¥8 •
48 8 34¥48¥8 58 10 38¥58¥10
52 8 34¥52¥8 60 10 38¥60¥10
62 10 34¥62¥10 62 7 38¥62¥7 •
62 8 38¥62¥8 •
35 45 7 35¥45¥7 62 10 38¥62¥10
47 6 35¥47¥6 72 10 38¥72¥10
47 7 35¥47¥7 •
47 8 35¥47¥8 • 80 8 38¥80¥8
48 8 35¥48¥8 38,5 58 7 38.5¥58¥7
49 6 35¥49¥6 40 50 8 40¥50¥8
50 7 35¥50¥7 • 52 6 40¥52¥6
50 8 35¥50¥8 • 52 7 40¥52¥7 •
50 10 35¥50¥10 52 8 40¥52¥8 •
52 7 35¥52¥7 • 55 7 40¥55¥7 •
52 8 35¥52¥8 • 55 8 40¥55¥8 •
52 10 35¥52¥10
56 8 40¥56¥8
55 7 35¥55¥7 •
55 8 35¥55¥8 • 58 7 40¥58¥7
55 10 35¥55¥10 58 8 40¥58¥8
58 10 40¥58¥10
56 10 35¥56¥10
60 8 40¥60¥8
58 10 35¥58¥10 60 10 40¥60¥10
60 10 35¥60¥10 62 6 40¥62¥6
62 7 40¥62¥7 •
62 7 35¥62¥7 62 8 40¥62¥8 •
62 8 35¥62¥8 62 10 40¥62¥10
62 10 35¥62¥10
65 10 40¥65¥10
65 12 40¥65¥12

d1 40 – 65 mm
b
d1 D

d1 D b d1 D b
mm – – mm – –
40 68 8 40¥68¥8 44 60 10 44¥60¥10
cont. 68 10 40¥68¥10
62 10 44¥62¥10
70 8 40¥70¥8
65 10 44¥65¥10
72 7 40¥72¥7
72 10 40¥72¥10 45 55 7 45¥55¥7
80 8 40¥80¥8 58 7 45¥58¥7
80 10 40¥80¥10
80 12 40¥80¥12 60 7 45¥60¥7
60 8 45¥60¥8 •
90 10 40¥90¥10 60 10 45¥60¥10
90 12 40¥90¥12
62 7 45¥62¥7
41 56 7 41¥56¥7 62 8 45¥62¥8 •
62 10 45¥62¥10
42 53 7 42¥53¥7
65 8 45¥65¥8 •
55 7 42¥55¥7 65 10 45¥65¥10
55 8 42¥55¥8 •
68 7 45¥68¥7
56 7 42¥56¥7 68 10 45¥68¥10
68 12 45¥68¥12
60 7 42¥60¥7
72 8 45¥72¥8
62 7 42¥62¥7 72 10 45¥72¥10
62 8 42¥62¥8 •
62 10 42¥62¥10 75 8 45¥75¥8
75 10 45¥75¥10
65 10 42¥65¥10
65 12 42¥65¥12 80 10 45¥80¥10
66 10 42¥66¥10 85 10 45¥85¥10
67 10 42¥67¥10 100 10 45¥100¥10
42 72 8 42¥72¥8 46 59 12 46¥59¥12
72 10 42¥72¥10
65 10 46¥65¥10
43 62 8 43¥62¥8

d1 D b d1 D b
mm – – mm – –
47 65 10 47¥65¥10 55 75 8 55¥75¥8
cont. 75 10 55¥75¥10
70 10 47¥70¥10
78 10 55¥78¥10
2.1
90 10 47¥90¥10 78 12 55¥78¥12
48 62 8 48¥62¥8 • 80 8 55¥80¥8 •
80 10 55¥80¥10
65 10 48¥65¥10
85 8 55¥85¥8
68 10 48¥68¥10 85 10 55¥85¥10
70 10 48¥70¥10 90 8 55¥90¥8
90 10 55¥90¥10
72 7 48¥72¥7
72 8 48¥72¥8 100 10 55¥100¥10
72 10 48¥72¥10 100 12 55¥100¥12
50 62 7 50¥62¥7 56 72 8 56¥72¥8
64 6 50¥64¥6 57 67 7 57¥67¥7
65 8 50¥65¥8 • 58 72 8 58¥72¥8
65 10 50¥65¥10
80 8 58¥80¥8
68 7 50¥68¥7 80 10 58¥80¥10
68 8 50¥68¥8 • 80 12 58¥80¥12
68 10 50¥68¥10
60 72 8 60¥72¥8
70 10 50¥70¥10
75 8 60¥75¥8 •
72 8 50¥72¥8 •
72 10 50¥72¥10 80 7 60¥80¥7
72 12 50¥72¥12 80 8 60¥80¥8 •
80 10 60¥80¥10
75 10 50¥75¥10
82 12 60¥82¥12
80 8 50¥80¥8
80 10 50¥80¥10 85 8 60¥85¥8 •
85 10 60¥85¥10
85 10 50¥85¥10
90 8 60¥90¥8
90 10 50¥90¥10 90 10 60¥90¥10
100 10 50¥100¥10 95 10 60¥95¥10
52 63 8 52¥63¥8 100 10 60¥100¥10
65 8 52¥65¥8 110 8 60¥110¥8

110 8 60¥110¥10
68 8 52¥68¥8
62 80 10 62¥80¥10
72 8 52¥72¥8
72 10 52¥72¥10 85 10 62¥85¥10
80 10 52¥80¥10 90 10 62¥90¥10
85 10 52¥85¥10 63 85 10 63¥85¥10
100 10 52¥100¥10 90 10 63¥90¥10
55 68 8 55¥68¥8 64 80 8 64¥80¥8
70 8 55¥70¥8 • 65 80 8 65¥80¥8
70 10 55¥70¥10
85 8 65¥85¥8
72 8 55¥72¥8 • 85 10 65¥85¥10 •
72 10 55¥72¥10 85 12 65¥85¥12

d1 65 – 190 mm
b
d1 D

d1 D b d1 D b
mm – – mm – –
65 88 12 65¥88¥12 75 90 10 75¥90¥10
cont.
90 10 65¥90¥10 • 95 10 75¥95¥10 •
95 12 75¥95¥12
95 10 65¥95¥10
100 10 75¥100¥10 •
97 7 65¥97¥7 100 12 75¥100¥12
100 10 65¥100¥10 105 10 75¥105¥10
110 10 65¥110¥10 110 12 75¥110¥12
120 12 65¥120¥12 120 12 75¥120¥12
140 12 65¥140¥12 130 12 75¥130¥12
68 90 10 68¥90¥10 78 100 10 78¥100¥10
70 85 8 70¥85¥8 80 95 10 80¥95¥10
90 7 70¥90¥72) 100 10 80¥100¥10 •

90 10 70¥90¥10 • 100 12 80¥100¥12
90 12 70¥90¥12
105 10 80¥105¥10
92 12 70¥92¥12
110 10 80¥110¥10 •
95 10 70¥95¥10 • 110 12 80¥110¥12
100 10 70¥100¥10 115 12 80¥115¥12
110 10 70¥110¥10 125 12 80¥125¥12

110 12 70¥110¥12
170 13 80¥170¥13
72 90 10 72¥90¥10
82 120 12 82¥120¥12
95 10 72¥95¥10
95 12 72¥95¥12 160 15 82¥160¥15
100 10 72¥100¥10 85 100 9 85¥100¥9

100 10 85¥100¥10
140 12 72¥140¥12
105 12 85¥105¥12

d1 D b d1 D b
mm – – mm – –
85 110 12 85¥110¥12 • 118 150 12 118¥150¥12

cont.
115 12 85¥115¥12 120 140 12
140 13
120¥140¥12
120¥140¥13
2.1
120 12 85¥120¥12 •
150 12 120¥150¥12
130 12 85¥130¥12
160 12 120¥160¥12
140 12 85¥140¥12
180 15 120¥180¥15
150 12 85¥150¥12
125 150 12 125¥150¥12 •
90 110 10 90¥110¥10
110 12 90¥110¥12 • 160 15 125¥160¥15
115 12 90¥115¥12 200 15 125¥200¥15
120 12 90¥120¥12 • 130 160 12 130¥160¥12 •

160 15 130¥160¥15
95 110 12 95¥110¥12
170 12 130¥170¥12
115 12 95¥115¥12
180 12 130¥180¥12
120 12 95¥120¥12 •
190 12 130¥190¥12
125 12 95¥125¥12 •
135 170 12 135¥170¥12 •
140 12 95¥140¥12
140 160 12 140¥160¥12
145 12 95¥145¥12
170 12 140¥170¥12 •
170 13 95¥170¥13 170 15 140¥170¥15
100 120 10 100¥120¥10 180 12 140¥180¥12

120 12 100¥120¥12 •
145 175 15 145¥175¥15 •
125 12 100¥125¥12 •
180 12 145¥180¥12
130 12 100¥130¥12 •
148 170 15 148¥170¥15
140 12 100¥140¥12
150 170 12 150¥170¥12
145 12 100¥145¥12
180 12 150¥180¥12
150 12 100¥150¥12 180 15 150¥180¥15 •
105 130 12 105¥130¥12 • 200 12 150¥200¥12
135 12 105¥135¥12 155 180 15 155¥180¥15
140 12 105¥140¥12 160 185 15 160¥185¥15
108 140 15 108¥140¥15 • 190 15 160¥190¥15 •
170 15 108¥170¥15 165 190 15 165¥190¥15
110 130 12 110¥130¥12 • 170 200 15 170¥200¥15 •

130 13 110¥130¥13
175 200 15 175¥200¥15
140 12 110¥140¥12 •
180 200 15 180¥200¥15
150 12 110¥150¥12
210 15 180¥210¥15 •
115 140 12 115¥140¥12 •
190 220 15 190¥220¥15 •
145 12 115¥145¥12
225 15 190¥225¥15
150 12 115¥150¥12

d1 200 – 250 mm
1) Designationto be followed by the design and material codes,
b
2) Design
execution differs from the basic design and is indicated
d1 D
Dimensions Designation1) ISO/DIN

Shaft Bore Nominal
seal width
d1 D b
mm – –
200 230 15 200¥230¥15 •
210 240 15 210¥240¥15 •
220 250 15 220¥250¥15 •
230 260 15 230¥260¥15 •
240 270 15 240¥270¥15 •
250 280 15 250¥280¥15 •
285 15 250¥285¥15
2.1
Radial shaft seals
CRW1, CRWA1, CRWH1 and CRWHA1

seals
These radial shaft seals are low-friction seals
with SKF Wave lip design for reduced heat CRW1
generation. See pages 57 and 58 for more
information on SKF Wave lip design. They have a
metal outside diameter for easy installation and
a firm and accurate fit in the housing bore.
The seals feature SKF Bore Tite Coating
on the outside diameter, a non-hardening, CRWH1
water-based acrylic sealant that helps fill small
imperfections in the housing bore.
They are primarily designed to retain lubri-
cants but are also suitable for contaminant ex-
clusion, especially the CRWA1 and CRWHA1
seals designed with an auxiliary lip. CRWA1
CRW1: Seal with a single steel case, SKF Wave

lip and a carbon steel garter spring.
CRWH1: Seal with a double steel case, SKF Wave

lip and a carbon steel garter spring. CRWHA1
CRWA1: Seal with a single steel case, SKF Wave

lip, a carbon steel garter spring and an auxiliary,
non-contacting lip.
CRWHA1: Seal with a double steel case,

SKF Wave lip, a carbon steel garter spring and
an auxiliary, non-contacting lip.
All of these seals are available with sealing lips

made of either nitrile rubber or the SKF devel-
oped fluoro rubber compound SKF Duralife.
Other materials are also available on request.
See matrix 1 on pages 90 and 91 for
permissible operating conditions.
Radial shaft seals – CRW1, CRWA1, CRWH1 and CRWHA1 – metric dimensions
d1 12 – 17 mm
d1 D
2.2
Dimensions Design and Designation

Shaft Bore Nominal lip material
seal width
d1 D b
mm – –
12 22 7 CRW1 V 12¥22¥7 CRW1 V

22 7 CRW1 R 12¥22¥7 CRW1 R
25 7 CRW1 R 12¥25¥7 CRW1 R
26 7 CRW1 R 12¥26¥7 CRW1 R
28 7 CRW1 R 12¥28¥7 CRW1 R
28 7 CRW1 P 12¥28¥7 CRW1 P
32 7 CRW1 R 12¥32¥7 CRW1 R

32 7 CRW1 V 12¥32¥7 CRW1 V
35 7 CRW1 R 12¥35¥7 CRW1 R
14 26 7 CRW1 V 14¥26¥7 CRW1 V

32 7 CRW1 R 14¥32¥7 CRW1 R
15 25 7 CRW1 P 15¥25¥7 CRW1 P

28 7 CRW1 R 15¥28¥7 CRW1 R
32 7 CRW1 R 15¥32¥7 CRW1 R
32 7 CRW1 V 15¥32¥7 CRW1 V
35 7 CRW1 R 15¥35¥7 CRW1 R

35 7 CRW1 P 15¥35¥7 CRW1 P
16 28 7 CRW1 R 16¥28¥7 CRW1 R

30 7 CRW1 R 16¥30¥7 CRW1 R
32 7 CRW1 R 16¥32¥7 CRW1 R
35 7 CRW1 R 16¥35¥7 CRW1 R
40 7 CRW1 R 16¥40¥7 CRW1 R

40 7 CRWA1 R 16¥40¥7 CRWA1 R
17 27 6,35 CRW1 R 17¥27¥6 CRW1 R

28 7 CRW1 R 17¥28¥7 CRW1 R
28 7 CRW1 V 17¥28¥7 CRW1 V
30 7 CRW1 R 17¥30¥7 CRW1 R

32 7 CRW1 R 17¥32¥7 CRW1 R
35 7 CRW1 R 17¥35¥7 CRW1 R
35 7 CRW1 V 17¥35¥7 CRW1 V
40 7 CRW1 R 17¥40¥7 CRW1 R

47 7 CRW1 R 17¥47¥7 CRW1 R
d1 18 – 28 mm
d1 D

seal width
d1 D b
mm – –
18 30 7 CRW1 R 18¥30¥7 CRW1 R

30 7 CRW1 V 18¥30¥7 CRW1 V
32 7 CRW1 R 18¥32¥7 CRW1 R
32 7 CRW1 V 18¥32¥7 CRW1 V
35 7 CRW1 R 18¥35¥7 CRW1 R

40 7 CRW1 R 18¥40¥7 CRW1 R
19 35 7 CRW1 R 19¥35¥7 CRW1 R
20 30 7 CRW1 R 20¥30¥7 CRW1 R

31 7 CRW1 R 20¥31¥7 CRW1 R
32 7 CRW1 R 20¥32¥7 CRW1 R
35 7 CRW1 R 20¥35¥7 CRW1 R

35 7 CRW1 V 20¥35¥7 CRW1 V
36 7 CRW1 R 20¥36¥7 CRW1 R
36 7 CRW1 V 20¥36¥7 CRW1 V
37 7 CRW1 R 20¥37¥7 CRW1 R

38 7 CRW1 R 20¥38¥7 CRW1 R
40 7 CRW1 R 20¥40¥7 CRW1 R

40 7 CRW1 V 20¥40¥7 CRW1 V
42 7 CRW1 R 20¥42¥7 CRW1 R
47 7 CRW1 R 20¥47¥7 CRW1 R
52 7 CRW1 R 20¥52¥7 CRW1 R

52 7 CRW1 P 20¥52¥7 CRW1 P
21 35 7 CRW1 R 21¥35¥7 CRW1 R

35 7 CRW1 V 21¥35¥7 CRW1 V
40 8 CRW1 R 21¥40¥8 CRW1 R

seal width
d1 D b
mm – –
22 31 7 CRW1 P 22¥31¥7 CRW1 P

32 7 CRW1 R 22¥32¥7 CRW1 R
35 7 CRW1 R 22¥35¥7 CRW1 R

2.2
35 7 CRW1 V 22¥35¥7 CRW1 V
38 7 CRW1 R 22¥38¥7 CRW1 R
38 7 CRW1 V 22¥38¥7 CRW1 V
40 6,35 CRW1 R 22¥40¥6 CRW1 R

40 6,35 CRW1 V 22¥40¥6 CRW1 V
42 7 CRW1 R 22¥42¥7 CRW1 R
47 8 CRW1 R 22¥47¥8 CRW1 R

50 8 CRW1 R 22¥50¥8 CRW1 R
24 36 7 CRW1 V 24¥36¥7 CRW1 V

38 7 CRW1 V 24¥38¥7 CRW1 V
47 8 CRW1 R 24¥47¥8 CRW1 R
25 35 7 CRW1 R 25¥35¥7 CRW1 R

35 7 CRW1 V 25¥35¥7 CRW1 V
36 7 CRW1 R 25¥36¥7 CRW1 R
37 7 CRW1 R 25¥37¥7 CRW1 R

37 7 CRW1 V 25¥37¥7 CRW1 V
38 7 CRW1 R 25¥38¥7 CRW1 R
38 7 CRW1 V 25¥38¥7 CRW1 V
40 7 CRW1 R 25¥40¥7 CRW1 R

40 7 CRW1 R 25¥40¥7 CRW1 R
40 7 CRW1 V 25¥40¥7 CRW1 V
42 8 CRW1 V 25¥42¥8 CRW1 V

42 8 CRW1 R 25¥42¥8 CRW1 R
45 7 CRW1 R 25¥45¥7 CRW1 R

47 6,35 CRW1 R 25¥47¥6 CRW1 R
48 8 CRW1 R 25¥48¥8 CRW1 R
48 8 CRW1 V 25¥48¥8 CRW1 V
50 8 CRW1 R 25¥50¥8 CRW1 R

52 8 CRW1 R 25¥52¥8 CRW1 R
52 8 CRW1 V 25¥52¥8 CRW1 V
62 7 CRW1 R 25¥62¥7 CRW1 R

62 7 CRW1 V 25¥62¥7 CRW1 V
27 42 7 CRW1 R 27¥42¥7 CRW1 R

42 7 CRW1 V 27¥42¥7 CRW1 V
43 8 CRW1 V 27¥43¥8 CRW1 V
45 8 CRW1 V 27¥45¥8 CRW1 V
52 8 CRW1 R 27¥52¥8 CRW1 R
28 40 7 CRW1 R 28¥40¥7 CRW1 R

40 7 CRW1 V 28¥40¥7 CRW1 V
42 7 CRW1 R 28¥42¥7 CRW1 R

42 7 CRW1 V 28¥42¥7 CRW1 V
45 7 CRW1 V 28¥45¥7 CRW1 V
47 7 CRW1 V 28¥47¥7 CRW1 V

47 8 CRW1 R 28¥47¥8 CRW1 R
52 8 CRW1 R 28¥52¥8 CRW1 R
d1 30 – 36 mm
d1 D

seal width
d1 D b
mm – –
30 40 7 CRW1 R 30¥40¥7 CRW1 R

40 7 CRW1 V 30¥40¥7 CRW1 V
42 7 CRW1 R 30¥42¥7 CRW1 R

42 7 CRW1 V 30¥42¥7 CRW1 V
45 8 CRW1 R 30¥45¥8 CRW1 R
45 8 CRW1 P 30¥45¥8 CRW1 P
47 7 CRW1 R 30¥47¥7 CRW1 R

47 8 CRW1 V 30¥47¥8 CRW1 V
48 8 CRW1 R 30¥48¥8 CRW1 R
50 8 CRW1 R 30¥50¥8 CRW1 R

50 8 CRW1 V 30¥50¥8 CRW1 V
52 8 CRW1 R 30¥52¥8 CRW1 R
55 7 CRW1 R 30¥55¥7 CRW1 R

56 8 CRW1 R 30¥56¥8 CRW1 R
58 8 CRWA1 R 30¥58¥8 CRWA1 R
60 8 CRW1 R 30¥60¥8 CRW1 R

62 7 CRW1 R 30¥62¥7 CRW1 R
62 7 CRW1 V 30¥62¥7 CRW1 V
72 8 CRW1 R 30¥72¥8 CRW1 R

72 12 CRWA1 V 30¥72¥12 CRWA1 V
32 42 7 CRW1 R 32¥42¥7 CRW1 R

42 7 CRW1 V 32¥42¥7 CRW1 V
45 8 CRW1 R 32¥45¥8 CRW1 R
47 8 CRW1 R 32¥47¥8 CRW1 R

47 8 CRW1 V 32¥47¥8 CRW1 V
48 8 CRW1 R 32¥48¥8 CRW1 R
48 8 CRW1 V 32¥48¥8 CRW1 V
50 8 CRW1 R 32¥50¥8 CRW1 R

50 8 CRW1 V 32¥50¥8 CRW1 V
52 8 CRW1 R 32¥52¥8 CRW1 R
52 8 CRW1 V 32¥52¥8 CRW1 V

seal width
d1 D b
mm – –
32 56 8 CRW1 R 32¥56¥8 CRW1 R

cont. 62 6,35 CRW1 R 32¥62¥6 CRW1 R
34 48 8 CRW1 R 34¥48¥8 CRW1 R

2.2
48 8 CRW1 V 34¥48¥8 CRW1 V
55 8 CRW1 R 34¥55¥8 CRW1 R

56 8 CRW1 R 34¥56¥8 CRW1 R
56 8 CRW1 V 34¥56¥8 CRW1 V
62 8 CRW1 R 34¥62¥8 CRW1 R
35 47 7 CRW1 R 35¥47¥7 CRW1 R

47 7 CRW1 V 35¥47¥7 CRW1 V
48 8 CRW1 R 35¥48¥8 CRW1 R
48 8 CRW1 V 35¥48¥8 CRW1 V
50 8 CRW1 R 35¥50¥8 CRW1 R

50 8 CRW1 V 35¥50¥8 CRW1 V
52 8 CRWA1 P 35¥52¥8 CRWA1 P

52 8 CRW1 R 35¥52¥8 CRW1 R
52 8 CRWA1 R 35¥52¥8 CRWA1 R
54 7 CRW1 R 35¥54¥7 CRW1 R

54 8 CRW1 V 35¥54¥8 CRW1 V
55 8 CRW1 R 35¥55¥8 CRW1 R
55 8 CRW1 V 35¥55¥8 CRW1 V1)
56 8 CRW1 R 35¥56¥8 CRW1 R

56 8 CRW1 V 35¥56¥8 CRW1 V
62 8 CRW1 V 35¥62¥8 CRW1 V
62 8 CRW1 R 35¥62¥8 CRW1 R
64 8 CRW1 R 35¥64¥8 CRW1 R

65 8 CRW1 V 35¥65¥8 CRW1 V
68 8 CRW1 R 35¥68¥8 CRW1 R
68 8 CRW1 V 35¥68¥8 CRW1 V
69 8 CRW1 R 35¥69¥8 CRW1 R
72 8 CRW1 V 35¥72¥8 CRW1 V

72 8 CRW1 R 35¥72¥8 CRW1 R
72 8 CRWA1 R 35¥72¥8 CRWA1 R
78 8 CRW1 R 35¥78¥8 CRW1 R
80 8 CRW1 R 35¥80¥8 CRW1 R
36 50 7 CRW1 R 36¥50¥7 CRW1 R

50 8 CRW1 R 36¥50¥8 CRW1 R
52 8 CRW1 R 36¥52¥8 CRW1 R
52 8 CRW1 V 36¥52¥8 CRW1 V
54 8 CRW1 R 36¥54¥8 CRW1 R

54 8 CRW1 V 36¥54¥8 CRW1 V
58 8 CRW1 R 36¥58¥8 CRW1 R
60 8 CRW1 R 36¥60¥8 CRW1 R

60 8 CRW1 V 36¥60¥8 CRW1 V
62 8 CRW1 R 36¥62¥8 CRW1 R

65 8 CRW1 R 36¥65¥8 CRW1 R
68 8 CRW1 R 36¥68¥8 CRW1 R
1) Without SKF Bore Tite Coating
d1 38 – 43 mm
d1 D

seal width
d1 D b
mm – –
38 50 7 CRW1 R 38¥50¥7 CRW1 R

50 7 CRW1 V 38¥50¥7 CRW1 V
52 8 CRW1 R 38¥52¥8 CRW1 R

52 8 CRWA1 R 38¥52¥8 CRWA1 R
52 8 CRW1 V 38¥52¥8 CRW1 V
53 8 CRW1 R 38¥53¥8 CRW1 R

54 7 CRW1 P 38¥54¥7 CRW1 P1)
55 8 CRW1 R 38¥55¥8 CRW1 R

55 8 CRW1 V 38¥55¥8 CRW1 V
56 8 CRW1 V 38¥56¥8 CRW1 V
56 8 CRW1 R 38¥56¥8 CRW1 R
58 8 CRW1 R 38¥58¥8 CRW1 R

58 8 CRW1 V 38¥58¥8 CRW1 V
60 8 CRW1 R 38¥60¥8 CRW1 R

60 8 CRW1 V 38¥60¥8 CRW1 V
62 8 CRW1 R 38¥62¥8 CRW1 R

62 8 CRWA1 R 38¥62¥8 CRWA1 R
62 8 CRW1 V 38¥62¥8 CRW1 V
65 8 CRW1 R 38¥65¥8 CRW1 R

68 8 CRW1 R 38¥68¥8 CRW1 R
70 8 CRW1 R 38¥70¥8 CRW1 R

72 8 CRW1 R 38¥72¥8 CRW1 R
73 8 CRW1 R 38¥73¥8 CRW1 R
74 11 CRWA1 R 38¥74¥11 CRWA1 R

74 11 CRW1 V 38¥74¥11 CRW1 V
80 8 CRW1 R 38¥80¥8 CRW1 R

90 8 CRWA1 R 38¥90¥8 CRWA1 R

seal width
d1 D b
mm – –
40 52 7 CRW1 V 40¥52¥7 CRW1 V

52 7 CRW1 R 40¥52¥7 CRW1 R
54 7 CRW1 R 40¥54¥7 CRW1 R 2.2
55 8 CRW1 R 40¥55¥8 CRW1 R
55 8 CRW1 V 40¥55¥8 CRW1 V
56 7 CRW1 V 40¥56¥7 CRW1 V
56 8 CRW1 R 40¥56¥8 CRW1 R
57 8 CRW1 R 40¥57¥8 CRW1 R

58 8 CRW1 R 40¥58¥8 CRW1 R
58 8 CRW1 V 40¥58¥8 CRW1 V
60 8 CRW1 R 40¥60¥8 CRW1 R

60 8 CRW1 V 40¥60¥8 CRW1 V
62 8 CRW1 R 40¥62¥8 CRW1 R
62 8 CRW1 V 40¥62¥8 CRW1 V
65 8 CRW1 R 40¥65¥8 CRW1 R

68 8 CRW1 R 40¥68¥8 CRW1 R
70 8 CRW1 R 40¥70¥8 CRW1 R

72 8 CRW1 R 40¥72¥8 CRW1 R
74 8 CRW1 R 40¥74¥8 CRW1 R
75 8 CRW1 V 40¥75¥8 CRW1 V
80 8 CRW1 R 40¥80¥8 CRW1 R

80 8 CRW1 V 40¥80¥8 CRW1 V1)
90 8 CRW1 R 40¥90¥8 CRW1 R
41 53 7 CRW1 R 41¥53¥7 CRW1 R

55 8 CRW1 R 41¥55¥8 CRW1 R
62 8 CRW1 R 41¥62¥8 CRW1 R
42 55 8 CRW1 R 42¥55¥8 CRW1 R

55 8 CRW1 V 42¥55¥8 CRW1 V
56 7 CRW1 V 42¥56¥7 CRW1 V

56 8 CRW1 R 42¥56¥8 CRW1 R
58 8 CRW1 R 42¥58¥8 CRW1 R
58 8 CRW1 V 42¥58¥8 CRW1 V
60 8 CRW1 R 42¥60¥8 CRW1 R

60 8 CRW1 V 42¥60¥8 CRW1 V
62 8 CRW1 R 42¥62¥8 CRW1 R
62 8 CRW1 V 42¥62¥8 CRW1 V
65 8 CRW1 R 42¥65¥8 CRW1 R

65 8 CRW1 V 42¥65¥8 CRW1 V
72 8 CRW1 V 42¥72¥8 CRW1 V

72 8 CRW1 R 42¥72¥8 CRW1 R
43 57 8 CRW1 R 43¥57¥8 CRW1 R

60 8 CRW1 R 43¥60¥8 CRW1 R
69 8 CRW1 R 43¥69¥8 CRW1 R
73 8 CRW1 R 43¥73¥8 CRW1 R
d1 44 – 54 mm
d1 D

seal width
d1 D b
mm – –
44 60 8 CRW1 R 44¥60¥8 CRW1 R

60 8 CRW1 V 44¥60¥8 CRW1 V1)
62 8 CRW1 R 44¥62¥8 CRW1 R

65 8 CRW1 R 44¥65¥8 CRW1 R
68 8 CRW1 V 44¥68¥8 CRW1 V
70 8 CRW1 R 44¥70¥8 CRW1 R

72 8 CRW1 R 44¥72¥8 CRW1 R
45 60 8 CRW1 R 45¥60¥8 CRW1 R

60 8 CRW1 V 45¥60¥8 CRW1 V
62 8 CRWA1 V 45¥62¥8 CRWA1 V

62 8 CRW1 R 45¥62¥8 CRW1 R
65 8 CRW1 R 45¥65¥8 CRW1 R
65 8 CRW1 V 45¥65¥8 CRW1 V
68 8 CRW1 R 45¥68¥8 CRW1 R

68 8 CRW1 V 45¥68¥8 CRW1 V
68 8 CRWA1 R 45¥68¥8 CRWA1 R
72 8 CRW1 V 45¥72¥8 CRW1 V

72 8 CRW1 R 45¥72¥8 CRW1 R
75 8 CRW1 R 45¥75¥8 CRW1 R

75 8 CRW1 V 45¥75¥8 CRW1 V
80 8 CRW1 R 45¥80¥8 CRW1 R

85 8 CRW1 R 45¥85¥8 CRW1 R
46 60 8 CRW1 R 46¥60¥8 CRW1 R

65 8 CRW1 R 46¥65¥8 CRW1 R
68 8 CRW1 R 46¥68¥8 CRW1 R
72 8 CRW1 R 46¥72¥8 CRW1 R

73 8 CRW1 R 46¥73¥8 CRW1 R

seal width
d1 D b
mm – –
47 60 7 CRW1 R 47¥60¥7 CRW1 R

62 8 CRW1 R 47¥62¥8 CRW1 R
72 8 CRW1 R 47¥72¥8 CRW1 R 2.2
48 62 8 CRW1 R 48¥62¥8 CRW1 R
62 8 CRW1 P 48¥62¥8 CRW1 P
65 8 CRW1 R 48¥65¥8 CRW1 R

65 8 CRW1 V 48¥65¥8 CRW1 V
68 8 CRW1 V 48¥68¥8 CRW1 V
70 8 CRW1 R 48¥70¥8 CRW1 R

70 8 CRW1 V 48¥70¥8 CRW1 V
72 8 CRW1 R 48¥72¥8 CRW1 R
72 8 CRW1 V 48¥72¥8 CRW1 V
80 8 CRW1 R 48¥80¥8 CRW1 R
50 65 8 CRW1 R 50¥65¥8 CRW1 R

65 8 CRW1 V 50¥65¥8 CRW1 V
68 8 CRW1 R 50¥68¥8 CRW1 R
68 8 CRW1 V 50¥68¥8 CRW1 V
70 8 CRW1 R 50¥70¥8 CRW1 R

70 8 CRW1 V 50¥70¥8 CRW1 V
72 8 CRW1 R 50¥72¥8 CRW1 R

72 8 CRW1 V 50¥72¥8 CRW1 V
75 8 CRWA1 R 50¥75¥8 CRWA1 R
80 8 CRW1 R 50¥80¥8 CRW1 R

80 8 CRW1 V 50¥80¥8 CRW1 V
82 8 CRWA1 R 50¥82¥8 CRWA1 R
85 8 CRW1 R 50¥85¥8 CRW1 R
90 8 CRW1 R 50¥90¥8 CRW1 R

90 8 CRW1 V 50¥90¥8 CRW1 V
51 65 7 CRWA1 R 51¥65¥7 CRWA1 R

73 8 CRW1 R 51¥73¥8 CRW1 R
80 9,53 CRW1 R 51¥80¥10 CRW1 R

81 9,53 CRWH1 R 51¥81¥10 CRWH1 R
81 9,53 CRWHA1 R 51¥81¥10 CRWHA1 R
92 11,13 CRWH1 R 51¥92¥11 CRWH1 R
52 68 8 CRW1 R 52¥68¥8 CRW1 R

68 8 CRW1 V 52¥68¥8 CRW1 V
70 8 CRW1 R 52¥70¥8 CRW1 R
72 8 CRWA1 V 52¥72¥8 CRWA1 V

72 8 CRW1 R 52¥72¥8 CRW1 R
72 8 CRW1 V 52¥72¥8 CRW1 V
85 8 CRW1 R 52¥85¥8 CRW1 R
53 68 8 CRW1 V 53¥68¥8 CRW1 V
54 65 8 CRW1 R 54¥65¥8 CRW1 R

65 8 CRW1 V 54¥65¥8 CRW1 V
73 11,13 CRW1 R 54¥73¥11 CRW1 R

73 11,13 CRWA1 R 54¥73¥11 CRWA1 R
81 9,53 CRWA1 R 54¥81¥10 CRWA1 R
d1 55 – 70 mm
d1 D

seal width
d1 D b
mm – –
55 70 8 CRW1 R 55¥70¥8 CRW1 R

70 8 CRW1 V 55¥70¥8 CRW1 V
72 8 CRW1 R 55¥72¥8 CRW1 R

72 8 CRW1 V 55¥72¥8 CRW1 V
73 8 CRW1 V 55¥73¥8 CRW1 V
75 8 CRW1 R 55¥75¥8 CRW1 R

75 8 CRW1 V 55¥75¥8 CRW1 V
80 8 CRW1 R 55¥80¥8 CRW1 R

80 8 CRW1 V 55¥80¥8 CRW1 V
85 8 CRW1 R 55¥85¥8 CRW1 R
90 8 CRW1 R 55¥90¥8 CRW1 R

100 8 CRW1 R 55¥100¥8 CRW1 R
56 75 8 CRW1 R 56¥75¥8 CRW1 R
57 81 11 CRW1 R 57¥81¥11 CRW1 R

81 11 CRWA1 P 57¥81¥11 CRWA1 P
92 11 CRWH1 R 57¥92¥11 CRWH1 R

92 11 CRWHA1 R 57¥92¥11 CRWHA1 R
58 72 8 CRW1 R 58¥72¥8 CRW1 R

72 8 CRW1 S 58¥72¥8 CRW1 S
75 8 CRW1 R 58¥75¥8 CRW1 R
80 8 CRW1 R 58¥80¥8 CRW1 R

80 8 CRW1 V 58¥80¥8 CRW1 V
85 8 CRW1 R 58¥85¥8 CRW1 R

90 8 CRW1 R 58¥90¥8 CRW1 R

seal width
d1 D b
mm – –
60 75 8 CRW1 R 60¥75¥8 CRW1 R

75 8 CRW1 V 60¥75¥8 CRW1 V
80 8 CRW1 R 60¥80¥8 CRW1 R

2.2
80 8 CRW1 V 60¥80¥8 CRW1 V
82 8 CRWA1 R 60¥82¥8 CRWA1 R
85 8 CRW1 V 60¥85¥8 CRW1 V

85 8 CRW1 R 60¥85¥8 CRW1 R
90 8 CRW1 R 60¥90¥8 CRW1 R
105 8 CRW1 R 60¥105¥8 CRW1 R

110 8 CRW1 R 60¥110¥8 CRW1 R
62 80 8 CRW1 V 62¥80¥8 CRW1 V

85 8 CRW1 R 62¥85¥8 CRW1 R
90 8 CRW1 R 62¥90¥8 CRW1 R

90 11,13 CRWH1 R 62¥90¥11 CRWH1 R
63 78 8 CRW1 R 63¥78¥8 CRW1 R

80 8 CRW1 R 63¥80¥8 CRW1 R
85 8 CRW1 R 63¥85¥8 CRW1 R
88 8 CRW1 R 63¥88¥8 CRW1 R
65 80 8 CRW1 R 65¥80¥8 CRW1 R

80 8 CRW1 V 65¥80¥8 CRW1 V
85 8 CRW1 R 65¥85¥8 CRW1 R

85 8 CRW1 V 65¥85¥8 CRW1 V
88 8 CRW1 R 65¥88¥8 CRW1 R
90 8 CRW1 R 65¥90¥8 CRW1 R

90 8 CRW1 V 65¥90¥8 CRW1 V
92 11,13 CRWH1 R 65¥92¥11 CRWH1 R
100 8 CRW1 R 65¥100¥8 CRW1 R

100 8 CRW1 V 65¥100¥8 CRW1 V
110 10 CRW1 R 65¥110¥10 CRW1 R
120 8 CRW1 R 65¥120¥8 CRW1 R
68 85 8 CRW1 R 68¥85¥8 CRW1 R

88 8 CRW1 R 68¥88¥8 CRW1 R
90 8 CRW1 R 68¥90¥8 CRW1 R

90 8 CRW1 V 68¥90¥8 CRW1 V
95 10 CRW1 R 68¥95¥10 CRW1 R

95 10 CRW1 V 68¥95¥10 CRW1 V
100 10 CRW1 R 68¥100¥10 CRW1 R
70 85 8 CRW1 R 70¥85¥8 CRW1 R

88 8 CRW1 R 70¥88¥8 CRW1 R
88 8 CRW1 V 70¥88¥8 CRW1 V
90 8 CRW1 R 70¥90¥8 CRW1 R

90 10 CRW1 V 70¥90¥10 CRW1 V
90 10 CRWHA1 P 70¥90¥10 CRWHA1 P
92 11 CRWH1 R 70¥92¥11 CRWH1 R

92 11 CRWH1 V 70¥92¥11 CRWH1 V
95 10 CRW1 R 70¥95¥10 CRW1 R
100 10 CRW1 R 70¥100¥10 CRW1 R

105 10 CRW1 R 70¥105¥10 CRW1 R
d1 70 – 110 mm
d1 D

seal width
d1 D b
mm – –
70 110 10 CRW1 R 70¥110¥10 CRW1 R

cont.
110 12,70 CRWHA1 R 70¥110¥13 CRWHA1 R1)
72 88 8 CRW1 R 72¥88¥8 CRW1 R
73 92 11,13 CRWH1 R 73¥92¥11 CRWH1 R

110 11,13 CRWA1 P 73¥110¥11 CRWA1 P
75 90 8 CRW1 R 75¥90¥8 CRW1 R

95 10 CRW1 R 75¥95¥10 CRW1 R
95 10 CRW1 V 75¥95¥10 CRW1 V
100 10 CRW1 R 75¥100¥10 CRW1 R

100 10 CRW1 V 75¥100¥10 CRW1 V
105 10 CRW1 R 75¥105¥10 CRW1 R
110 10 CRW1 R 75¥110¥10 CRW1 R

115 12 CRW1 R 75¥115¥12 CRW1 R
80 100 10 CRW1 R 80¥100¥10 CRW1 R

100 10 CRW1 V 80¥100¥10 CRW1 V
105 10 CRW1 R 80¥105¥10 CRW1 R
105 10 CRW1 V 80¥105¥10 CRW1 V
110 10 CRW1 R 80¥110¥10 CRW1 R
125 10 CRW1 R 80¥125¥10 CRW1 R

125 10 CRW1 V 80¥125¥10 CRW1 V
130 12 CRWA1 R 80¥130¥12 CRWA1 R

140 12 CRW1 R 80¥140¥12 CRW1 R
84 127 11 CRWH1 R 84¥127¥11 CRWH1 R

seal width
d1 D b
mm – –
85 105 10 CRW1 R 85¥105¥10 CRW1 R

105 10 CRW1 V 85¥105¥10 CRW1 V
110 10 CRW1 R 85¥110¥10 CRW1 R

2.2
110 10 CRWA1 V 85¥110¥10 CRWA1 V
120 12 CRW1 R 85¥120¥12 CRW1 R

130 12 CRW1 R 85¥130¥12 CRW1 R
89 127 11,13 CRWH1 R 89¥127¥11 CRWH1 R
90 110 12 CRW1 R 90¥110¥12 CRW1 R

110 12 CRW1 V 90¥110¥12 CRW1 V
115 12 CRWA1 R 90¥115¥12 CRWA1 R
120 12 CRW1 R 90¥120¥12 CRW1 R

120 12 CRW1 V 90¥120¥12 CRW1 V
125 12 CRW1 R 90¥125¥12 CRW1 R
125 12 CRW1 V 90¥125¥12 CRW1 V
130 12 CRW1 R 90¥130¥12 CRW1 R

140 12 CRWA1 R 90¥140¥12 CRWA1 R
92 127 11 CRWHA1 R 92¥127¥11 CRWHA1 R

127 11,13 CRWH1 R 92¥127¥11 CRWH1 R
95 110 10 CRW1 R 95¥110¥10 CRW1 R

115 12 CRW1 R 95¥115¥12 CRW1 R
115 12 CRW1 V 95¥115¥12 CRW1 V
120 12 CRW1 R 95¥120¥12 CRW1 R

120 12 CRW1 V 95¥120¥12 CRW1 V
120 12 CRWA1 V 95¥120¥12 CRWA1 V
125 12 CRW1 R 95¥125¥12 CRW1 R
130 12 CRW1 R 95¥130¥12 CRW1 R

130 12 CRW1 V 95¥130¥12 CRW1 V
98 120 12 CRW1 V 98¥120¥12 CRW1 V
100 120 12 CRW1 R 100¥120¥12 CRW1 R

120 12 CRW1 V 100¥120¥12 CRW1 V
125 12 CRW1 R 100¥125¥12 CRW1 R

125 12 CRW1 V 100¥125¥12 CRW1 V
127 11,13 CRWH1 R 100¥127¥11 CRWH1 R
130 12 CRW1 R 100¥130¥12 CRW1 R

135 12 CRWA1 R 100¥135¥12 CRWA1 R
140 12 CRWA1 R 100¥140¥12 CRWA1 R
105 127 11,13 CRWH1 R 105¥127¥11 CRWH1 R

130 12 CRW1 R 105¥130¥12 CRW1 R
130 12 CRW1 V 105¥130¥12 CRW1 V
135 12 CRWA1 R 105¥135¥12 CRWA1 R
140 12 CRWA1 R 105¥140¥12 CRWA1 R

160 12 CRW1 R 105¥160¥12 CRW1 R
110 130 12 CRW1 R 110¥130¥12 CRW1 R

130 12 CRW1 V 110¥130¥12 CRW1 V
135 12 CRW1 V 110¥135¥12 CRW1 V
140 12 CRW1 V 110¥140¥12 CRW1 V

140 12 CRW1 R 110¥140¥12 CRW1 R
145 12 CRW1 R 110¥145¥12 CRW1 R

160 12 CRWH1 R 110¥160¥12 CRWH1 R
d1 115 – 280 mm
d1 D

seal width
d1 D b
mm – –
115 135 12 CRW1 R 115¥135¥12 CRW1 R

140 12 CRW1 R 115¥140¥12 CRW1 R
140 12 CRW1 V 115¥140¥12 CRW1 V
145 12 CRW1 R 115¥145¥12 CRW1 R

150 12 CRW1 R 115¥150¥12 CRW1 R
160 12 CRW1 R 115¥160¥12 CRW1 R
120 140 12 CRWA1 R 120¥140¥12 CRWA1 R

145 12 CRW1 R 120¥145¥12 CRW1 R
150 12 CRW1 R 120¥150¥12 CRW1 R

160 12 CRWH1 R 120¥160¥12 CRWH1 R
125 150 12 CRW1 R 125¥150¥12 CRW1 R

150 12 CRW1 V 125¥150¥12 CRW1 V
160 12 CRW1 R 125¥160¥12 CRW1 R
130 160 12 CRW1 R 130¥160¥12 CRW1 R

160 12 CRW1 V 130¥160¥12 CRW1 V
170 12 CRW1 R 130¥170¥12 CRW1 R
140 160 12 CRW1 R 140¥160¥12 CRW1 R

170 12 CRW1 R 140¥170¥12 CRW1 R
170 12 CRW1 V 140¥170¥12 CRW1 V1)
143 181 12,70 CRWHA1 R 143¥181¥13 CRWHA1 R
160 190 15 CRW1 V 160¥190¥15 CRW1 V
162 200 14,30 CRWHA1 R 162¥200¥14 CRWHA1 R

200 15,88 CRWH1 R 162¥200¥16 CRWH1 R
188 215 16 CRWH1 R 188¥215¥16 CRWH1 R
203 254 15,88 CRWHA1 R 203¥254¥16 CRWHA1 R1)
216 254 15,88 CRWH1 R 216¥254¥16 CRWH1 R

seal width
d1 D b
mm – –
220 250 16 CRWH1 R 220¥250¥16 CRWH1 R
280 320 20
320 20
CRWA1 R
CRWA1 V
280¥320¥20 CRWA1 R
280¥320¥20 CRWA1 V
2.2
Radial shaft seals – CRW1, CRWA1, CRWH1 and CRWHA1 – inch dimensions
d1 0.250 – 0.669 in.
d1 D

seal width
d1 D b
in. – –
0.250 0.749 0.250 CRW1 V 25131)

0.749 0.250 CRW1 R 2514
0.375 0.749 0.250 CRW1 R 36871)

0.749 0.250 CRW1 V 3688
0.750 0.250 CRWA1 R 3680
0.836 0.188 CRW1 P 3719

0.875 0.250 CRW1 R 3725
0.999 0.250 CRW1 R 37511)

0.999 0.250 CRW1 V 3752
1.124 0.250 CRW1 R 38061)
0.438 0.875 0.250 CRW1 P 4249

0.875 0.250 CRW1 R 42511)
0.875 0.375 CRWA1 R 42611)
0.875 0.375 CRWA1 V 4262
0.999 0.250 CRW1 V 4356

0.999 0.375 CRW1 P 4353
0.999 0.375 CRW1 R 4355
1.124 0.250 CRW1 R 4390
0.500 0.875 0.250 CRW1 R 4931

0.875 0.250 CRW1 V 4932
0.875 0.250 CRWA1 V 4933
0.875 0.250 CRWA1 V 4935
0.875 0.250 CRW1 D 4936
0.875 0.313 CRWA1 R 4939
0.987 0.250 CRW1 R 4943

0.999 0.250 CRW1 V 4980
0.999 0.250 CRW1 R 4984
0.999 0.250 CRWA1 R 4985
1.124 0.250 CRW1 P 5045

1.124 0.250 CRWA1 R 5062
1.124 0.250 CRW1 V 5066

seal width
d1 D b
in. – –
0.500 1.124 0.250 CRWA1 V 5067

cont. 1.124 0.250 CRW1 R 5068
1.124 0.313 CRW1 P 5046 2.2
1.250 0.250 CRW1 R 5133
1.375 0.250 CRW1 R 5150
1.375 0.250 CRW1 V 5151
0.531 0.999 0.250 CRWA1 S 5321
0.546 0.875 0.250 CRW1 P 53851)
0.554 0.999 0.250 CRW1 R 5605
0.563 0.875 0.188 CRW1 D 5523

0.999 0.250 CRW1 R 5541
0.999 0.250 CRW1 V 5542
0.999 0.250 CRW1 R 5543
0.999 0.250 CRWA1 R 5606
1.124 0.250 CRW1 V 5650

1.124 0.250 CRW1 R 5652
1.124 0.250 CRWA1 R 5662
1.250 0.250 CRW1 R 5707

1.375 0.250 CRW1 R 5756
0.594 1.124 0.313 CRW1 R 5926

1.124 0.313 CRW1 V 5927
0.625 0.987 0.250 CRW1 R 6134

0.999 0.250 CRWA1 V 6139
0.999 0.250 CRWA1 R 6141
0.999 0.250 CRW1 R 6143
1.063 0.250 CRW1 R 6157

1.124 0.250 CRW1 R 6903
1.124 0.250 CRWA1 R 6904
1.124 0.250 CRW1 V 6823
1.124 0.250 CRWA1 V 6825
1.181 0.250 CRWA1 R 6247

1.181 0.256 CRWA1 V 6248
1.250 0.250 CRW1 V 6909

1.250 0.250 CRW1 R 6925
1.250 0.250 CRWA1 R 6916
1.375 0.250 CRW1 R 6372

1.375 0.250 CRWA1 R 6373
1.375 0.250 CRW1 V 6979
1.375 0.250 CRWA1 V 6383
1.377 0.250 CRWHA1 R 6391

1.499 0.250 CRW1 R 6422
0.656 1.124 0.313 CRW1 R 6523

1.250 0.250 CRW1 R 6541
1.375 0.313 CRW1 R 6556
1.575 0.250 CRW1 R 6582
0.669 0.999 0.188 CRW1 R 6595

1.064 0.250 CRW1 R 6728
1.064 0.250 CRW1 R 6729
1.573 0.281 CRW1 V 65971)
d1 0.688 – 0.875 in.
d1 D

seal width
d1 D b
in. – –
0.688 1.124 0.190 CRW1 R 6738

1.124 0.250 CRW1 R 6741
1.124 0.250 CRW1 R 6743
1.124 0.250 CRW1 V 6745
1.187 0.188 CRW1 V 6770
1.188 0.188 CRW1 R 6763
1.250 0.256 CRWA1 R 6765

1.250 0.256 CRWHA1 V 6751
1.250 0.313 CRW1 R 6767
1.250 0.313 CRW1 V 6768
1.252 0.220 CRWH1 V 6769
1.375 0.250 CRWA1 R 6814

1.375 0.313 CRW1 R 6816
1.375 0.313 CRW1 V 6817
1.499 0.250 CRW1 R 6935

1.624 0.250 CRWA1 R 6990
0.750 1.124 0.188 CRW1 R 7414

1.124 0.188 CRW1 V 7417
1.249 0.188 CRW1 V 74671)

1.250 0.188 CRW1 R 7439
1.250 0.188 CRW1 R 74781)
1.250 0.250 CRW1 R 7438
1.250 0.250 CRW1 R 7440

1.250 0.250 CRWA1 R 7443
1.250 0.250 CRW1 V 7450
1.250 0.250 CRWA1 V 7453
1.250 0.250 CRWA1 V 7455
1.252 0.188 CRW1 R 7469

1.260 0.250 CRW1 R 7473
1.312 0.250 CRW1 R 7474

1.312 0.250 CRWA1 R 7475
1.375 0.250 CRW1 R 7512

seal width
d1 D b
in. – –
0.750 1.375 0.250 CRWA1 R 7513

cont. 1.375 0.250 CRW1 V 7515

1.375
1.375
0.250
0.250
CRWA1 V
CRWA1 P
7517
7533
2.2
1.499 0.250 CRW1 V 7567
1.499 0.250 CRW1 R 75721)
1.499 0.250 CRWA1 R 7573
1.575 0.250 CRW1 R 7591
1.624 0.250 CRW1 V 7623

1.624 0.250 CRWA1 V 7624
1.624 0.250 CRW1 R 7627
1.624 0.250 CRWA1 R 7628
1.752 0.250 CRW1 R 7636

1.752 0.250 CRWA1 V 7638
1.828 0.250 CRW1 R 7661

1.874 0.250 CRW1 R 7690
2.047 0.313 CRW1 R 7693
0.781 1.375 0.313 CRW1 V 7824

1.375 0.313 CRW1 R 78291)
1.499 0.313 CRW1 R 7849
1.624 0.313 CRW1 R 7872
1.828 0.250 CRW1 P 7889
0.787 1.124 0.188 CRW1 R 7740
0.813 1.187 0.313 CRWA1 V 8013

1.250 0.188 CRW1 R 80171)
1.250 0.188 CRW1 P 8018
1.375 0.375 CRW1 V 8053

1.375 0.375 CRW1 R 8060
1.499 0.250 CRW1 R 80881)
1.624 0.250 CRW1 V 8178

1.752 0.375 CRW1 R 8215
0.875 1.250 0.188 CRW1 R 8624

1.250 0.250 CRW1 V 8621
1.308 0.250 CRW1 V 8649

1.375 0.250 CRW1 V 8646
1.375 0.250 CRW1 R 8648
1.437 0.250 CRW1 R 8691

1.499 0.250 CRW1 R 8700
1.499 0.250 CRWA1 R 8702
1.499 0.250 CRW1 V 8704
1.499 0.250 CRWA1 V 8707
1.499 0.313 CRW1 R 87031)
1.502 0.313 CRWA1 R 8748

1.575 0.250 CRW1 R 8763
1.624 0.250 CRWA1 R 8782

1.624 0.250 CRW1 V 8795
1.624 0.250 CRW1 R 8796
1.752 0.250 CRW1 R 8821

1.828 0.250 CRW1 R 8842
1.874 0.250 CRW1 R 8860
d1 0.875 – 1.063 in.
d1 D

seal width
d1 D b
in. – –
0.875 2.000 0.250 CRW1 R 8870

cont.
2.050 0.375 CRWH1 V 8871
0.882 2.088 0.313 CRWHA1 R 9000
0.938 1.375 0.250 CRWA1 R 9244

1.500 0.250 CRW1 R 9303
1.500 0.250 CRW1 V 9304
1.624 0.250 CRW1 R 9307

1.624 0.250 CRW1 V 9308
1.752 0.250 CRW1 R 9347

1.828 0.250 CRW1 R 9409
0.950 1.358 0.275 CRW1 P 9520
0.969 1.406 0.250 CRWA1 P 9604

1.499 0.313 CRW1 V 9611
1.499 0.313 CRW1 R 96131)
1.624 0.250 CRW1 R 9646

1.624 0.250 CRW1 V 9647
1.686 0.313 CRWA1 R 9663
1.686 0.313 CRW1 R 9664
1.752 0.250 CRW1 R 9667

1.828 0.313 CRW1 R 9681
0.981 1.376 0.313 CRW1 V 98881)
0.984 1.499 0.250 CRW1 V 9686

1.749 0.375 CRWA1 V 98031)
1.000 1.367 0.313 CRW1 R 9822

1.375 0.250 CRW1 P 98261)
1.375 0.250 CRW1 V 9831

seal width
d1 D b
in. – –
1.000 1.437 0.250 CRW1 V 9833

cont. 1.437 0.250 CRW1 R 9837

1.437
1.437
0.250
0.250
CRWA1 R
CRWA1 V
9838
9847
2.2
1.496 0.390 CRW1 R 9850
1.499 0.250 CRW1 R 9852
1.499 0.250 CRW1 V 9854
1.499 0.250 CRW1 R 9876
1.499 0.250 CRWA1 R 9878

1.499 0.250 CRWA1 V 9879
1.499 0.315 CRWA1 V 9862
1.499 0.315 CRW1 V 9892
1.561 0.250 CRW1 R 9894

1.575 0.313 CRWA1 R 9907
1.624 0.250 CRW1 R 9934

1.624 0.250 CRWA1 R 9935
1.624 0.250 CRW1 V 9937
1.624 0.250 CRWA1 V 9939
1.686 0.250 CRW1 R 9960
1.752 0.250 CRW1 V 9982

1.752 0.250 CRWA1 V 9983
1.752 0.250 CRW1 R 9997
1.752 0.250 CRWA1 R 9998
1.828 0.250 CRW1 V 10058

1.828 0.250 CRW1 P 10047
1.828 0.250 CRW1 R 10049
1.828 0.250 CRWA1 R 10050
1.851 0.250 CRW1 R 10071

1.874 0.250 CRW1 R 10075
1.938 0.250 CRW1 R 10104

1.983 0.250 CRWA1 V 10111
1.983 0.313 CRWA1 R 10114
2.000 0.250 CRW1 R 10123

2.000 0.250 CRWA1 R 10124
2.000 0.250 CRWA1 R 10127
2.000 0.250 CRW1 V 10128
2.000 0.250 CRWA1 V 10129
2.047 0.250 CRWA1 R 10157

2.062 0.250 CRW1 R 10158
2.250 0.250 CRW1 R 10169
1.063 1.499 0.250 CRW1 R 10515

1.499 0.250 CRW1 V 10518
1.512 0.256 CRW1 P 532866

1.561 0.250 CRW1 R 10581
1.577 0.250 CRW1 R 10583
1.624 0.250 CRW1 R 10598

1.686 0.250 CRW1 R 10632
1.752 0.250 CRW1 R 10653
1.828 0.250 CRW1 R 10681

1.828 0.250 CRW1 V 10682
1.874 0.250 CRW1 R 10700
1.979 0.250 CRW1 R 10728

1.983 0.250 CRW1 R 10733
d1 1.063 – 1.250 in.
d1 D

seal width
d1 D b
in. – –
1.063 2.000 0.250 CRW1 R 10740

cont.
2.062 0.250 CRW1 R 10766
1.125 1.499 0.188 CRW1 V 110591)

1.499 0.188 CRW1 R 110611)
1.561 0.250 CRW1 P 11066

1.561 0.250 CRW1 R 11067
1.561 0.250 CRW1 V 11071
1.565 0.250 CRW1 R 11082
1.624 0.250 CRW1 P 11111

1.624 0.250 CRW1 R 11123
1.624 0.250 CRWA1 R 11124
1.624 0.250 CRW1 V 11133
1.624 0.250 CRWA1 V 11134
1.733 0.375 CRW1 R 11137

1.752 0.250 CRW1 R 11138
1.752 0.250 CRW1 V 11144
1.828 0.250 CRW1 R 11170

1.828 0.250 CRWA1 R 11171
1.828 0.250 CRW1 V 11172
1.828 0.250 CRWA1 V 11175
1.852 0.313 CRWH1 R 11197

1.852 0.313 CRWHA1 R 11200
1.874 0.250 CRW1 V 11225

1.874 0.250 CRWA1 V 11218
1.874 0.250 CRW1 R 11224
1.874 0.250 CRWA1 R 11223
1.983 0.250 CRW1 R 11299
2.000 0.250 CRW1 R 11340

2.000 0.250 CRW1 V 11344
2.000 0.374 CRWA1 V 12138
2.000 0.375 CRWA1 R 11343

seal width
d1 D b
in. – –
1.125 2.047 0.313 CRWA1 R 11353

cont. 2.062 0.250 CRWA1 V 11368
2.062 0.313 CRW1 R 11366 2.2
2.125 0.313 CRW1 R 11372
2.125 0.313 CRW1 V 11373
2.250 0.250 CRW1 R 11378

2.441 0.250 CRW1 R 11392
1.126 1.575 0.236 CRWA1 R 11086
1.156 1.686 0.250 CRWA1 R 11518

1.752 0.250 CRWA1 R 11514
1.874 0.250 CRW1 R 11524

1.875 0.375 CRWA1 R 115361)
2.000 0.250 CRW1 R 11544

2.000 0.250 CRWA1 R 11545
2.000 0.250 CRW1 V 11550
2.062 0.313 CRW1 R 11558
1.175 2.031 0.500 CRW1 R 11553
1.178 2.073 0.335 CRW1 S 11650
1.188 1.561 0.313 CRW1 V 117101)

1.686 0.250 CRW1 P 11728
1.687 0.250 CRW1 R 11730
1.752 0.250 CRW1 R 11734

1.752 0.250 CRW1 V 11736
1.828 0.375 CRW1 R 11740

1.875 0.250 CRW1 P 11763
1.875 0.375 CRW1 R 11585
1.983 0.250 CRW1 R 11776

1.983 0.250 CRWA1 R 11777
2.000 0.250 CRW1 R 11800

2.000 0.250 CRWA1 R 11801
2.000 0.250 CRW1 V 11806
2.062 0.250 CRW1 R 11878
2.062 0.250 CRW1 P 11879
2.125 0.313 CRW1 R 11907

2.165 0.250 CRW1 R 11911
2.250 0.250 CRW1 R 11914
2.437 0.250 CRW1 R 11923

2.441 0.250 CRW1 R 11930
1.190 2.125 0.313 CRWHA1 R 11908
1.234 2.250 0.250 CRW1 R 12590
1.250 1.625 0.188 CRW1 R 12329

1.687 0.250 CRW1 V 12335
1.687 0.250 CRW1 R 12336
1.687 0.250 CRWA1 V 12337
1.687 0.313 CRWA1 R 12350
d1 1.250 – 1.375 in.
d1 D

seal width
d1 D b
in. – –
1.250 1.752 0.250 CRW1 V 12340

cont.
1.752 0.250 CRWA1 V 12343
1.752 0.250 CRW1 R 12363
1.752 0.250 CRWA1 R 12364
1.874 0.250 CRW1 P 12382

1.874 0.250 CRWA1 V 12383
1.874 0.250 CRW1 R 12384
1.874 0.250 CRWA1 R 12386
1.938 0.250 CRW1 R 12391

1.955 0.250 CRWA1 R 12396
1.983 0.250 CRW1 R 12427
1.983 0.250 CRWA1 R 12428
1.983 0.250 CRW1 V 12432
2.000 0.250 CRW1 V 12445

2.000 0.250 CRWA1 V 12446
2.000 0.250 CRW1 R 12456
2.000 0.250 CRWA1 R 12458
2.000 0.438 CRW1 P 12483
2.062 0.250 CRWA1 V 12531

2.062 0.433 CRWHA1 V 12533
2.062 0.438 CRWH1 R 12530
2.125 0.250 CRW1 V 12544

2.125 0.250 CRW1 R 12545
2.125 0.250 CRWA1 R 12551
2.250 0.250 CRW1 R 12577

2.327 0.500 CRW1 R 12610
2.374 0.313 CRW1 R 12613

2.374 0.313 CRWA1 R 12614
2.374 0.315 CRW1 V 12612
2.437 0.250 CRW1 R 12621

2.441 0.250 CRW1 R 12631
2.500 0.310 CRW1 V 12638

2.502 0.313 CRW1 R 12637

seal width
d1 D b
in. – –
1.301 2.046 0.492 CRWA1 R 12907
1.313

1.828
2.062
0.375
0.313
CRW1 P
CRW1 R
13021
13050
2.2
2.062 0.313 CRWA1 R 13052
2.062 0.313 CRW1 V 13054
2.125 0.313 CRW1 R 13092

2.250 0.313 CRW1 R 13112
2.282 0.250 CRWA1 R 13157
1.328 2.031 0.313 CRW1 R 134151)

2.061 0.313 CRW1 R 13350
2.227 0.313 CRW1 R 13418
1.344 2.106 0.313 CRW1 R 13421

2.125 0.313 CRW1 R 13437
1.365 1.956 0.438 CRW1 R 13985

2.081 0.313 CRW1 R 13598
2.261 0.313 CRW1 R 13700
1.375 1.750 0.250 CRW1 R 13514

1.828 0.250 CRWA1 V 13510
1.828 0.313 CRW1 R 13537
1.835 0.250 CRW1 R 13536

1.873 0.313 CRW1 V 13511
1.874 0.250 CRW1 P 13512

1.874 0.250 CRW1 R 13534
1.874 0.250 CRW1 V 13538
1.874 0.313 CRWA1 R 13535
1.938 0.250 CRWA1 R 13552

1.955 0.433 CRWA1 P 13527
1.983 0.313 CRW1 P 13557
2.000 0.313 CRWA1 P 13562

2.000 0.313 CRW1 R 13568
2.000 0.313 CRWA1 R 13569
2.000 0.313 CRWH1 R 13571
2.000 0.313 CRW1 V 13579
2.000 0.313 CRWA1 V 13581
2.062 0.313 CRW1 V 13582

2.062 0.313 CRW1 R 135851)
2.062 0.313 CRWA1 P 13588
2.062 0.315 CRWA1 V 13607
2.106 0.313 CRWA1 R 136021)

2.106 0.313 CRW1 P 13614
2.125 0.313 CRW1 R 13649

2.125 0.313 CRWA1 R 13651
2.125 0.313 CRWA1 V 13661
2.125 0.313 CRW1 V 13663
2.250 0.250 CRWA1 R 13698

2.250 0.313 CRW1 R 13671
2.250 0.313 CRWA1 R 13676
2.250 0.313 CRW1 V 13688
2.250 0.313 CRWA1 V 13691
2.250 0.313 CRW1 P 13869
d1 1.375 – 1.500 in.
d1 D

seal width
d1 D b
in. – –
1.375 2.374 0.313 CRW1 V 13734

cont.
2.374 0.313 CRW1 R 13738
2.374 0.313 CRWA1 R 13739
2.437 0.250 CRW1 R 13797

2.441 0.313 CRW1 R 13810
2.441 0.313 CRWA1 R 13812
2.502 0.313 CRW1 R 13865

2.502 0.313 CRW1 V 13867
2.502 0.374 CRWA1 V 13856
2.562 0.375 CRW1 R 13875

2.562 0.375 CRWA1 R 13876
2.562 0.375 CRWA1 V 13878
2.623 0.313 CRWA1 V 13882

2.686 0.500 CRW1 R 13892
2.716 0.313 CRW1 R 13900
2.812 0.375 CRWHA1 R 13912

2.835 0.313 CRWA1 R 13918
2.835 0.313 CRW1 R 13920
2.835 0.313 CRWA1 P 13925
2.875 0.313 CRWA1 P 13929
1.378 2.835 0.313 CRWA1 V 13926
1.417 2.616 0.313 CRW1 R 14092
1.438 2.062 0.313 CRW1 V 142121)

2.062 0.313 CRWA1 R 14214
2.125 0.313 CRW1 R 14223

2.125 0.313 CRWA1 V 14225
2.250 0.313 CRWA1 R 14247

2.250 0.313 CRWA1 V 14259
2.250 0.313 CRW1 V 14260
2.250 0.313 CRW1 R 14262

seal width
d1 D b
in. – –
1.438 2.374 0.313 CRW1 R 14282

cont. 2.374 0.313 CRWA1 R 14285
2.437 0.313 CRW1 R 14363

2.2
2.502 0.313 CRW1 R 14383
2.623 0.313 CRW1 R 14404

2.686 0.313 CRW1 R 14423
2.750 0.313 CRW1 R 14458
1.484 2.254 0.313 CRW1 R 14907
1.494 2.060 0.270 CRW1 R 14789
1.496 2.165 0.315 CRWA1 R 550250
1.500 1.874 0.250 CRW1 R 148071)

1.918 0.250 CRW1 V 148091)
1.983 0.250 CRW1 V 14821

1.983 0.250 CRWA1 R 14824
1.983 0.313 CRW1 R 14832
2.000 0.313 CRWA1 R 14846

2.000 0.313 CRW1 R 14855
2.000 0.313 CRW1 V 14861
2.048 0.313 CRWA1 R 14858

2.062 0.313 CRW1 R 14864
2.062 0.313 CRW1 V 14867
2.125 0.313 CRW1 R 14875

2.125 0.313 CRWA1 R 14876
2.125 0.313 CRW1 V 14886
2.125 0.313 CRWA1 V 14887
2.222 0.313 CRW1 R 14903

2.250 0.313 CRW1 S 14935
2.250 0.313 CRW1 R 14938
2.250 0.313 CRWA1 R 14939
2.250 0.313 CRW1 V 14940

2.250 0.313 CRWA1 V 14942
2.260 0.406 CRW1 R 14968
2.374 0.313 CRW1 V 14992

2.374 0.313 CRWA1 V 14994
2.374 0.313 CRW1 R 15004
2.374 0.313 CRWA1 R 15005

2.374 0.500 CRWH1 R 15039
2.377 0.453 CRWA1 R 15041
2.437 0.313 CRW1 R 15076

2.441 0.313 CRW1 R 150921)
2.441 0.313 CRWA1 R 15093
2.441 0.313 CRW1 V 15097
2.502 0.313 CRW1 V 15138

2.502 0.313 CRW1 R 15141
2.502 0.313 CRWA1 R 15142
2.561 0.313 CRW1 R 15176
2.623 0.313 CRW1 R 15194

2.686 0.500 CRW1 R 15207
d1 1.500 – 1.645 in.
d1 D

seal width
d1 D b
in. – –
1.500 2.716 0.438 CRW1 R 15204

cont.
2.750 0.313 CRW1 R 15214
2.758 0.313 CRW1 R 15230
2.835 0.313 CRW1 R 15234

2.875 0.313 CRW1 R 15235
1.552 2.502 0.500 CRWA1 R 15450

2.686 0.500 CRW1 R 15460
2.750 0.500 CRWHA1 P 15462
1.563 2.062 0.250 CRW1 V 15506

2.062 0.250 CRW1 R 15508
2.125 0.313 CRW1 R 155171)

2.125 0.313 CRWA1 P 15518
2.250 0.313 CRW1 R 15522
2.374 0.313 CRW1 P 155401)

2.374 0.313 CRW1 R 15542
2.374 0.313 CRWA1 R 15543
2.374 0.313 CRWA1 V 15549
2.437 0.313 CRW1 R 155921)

2.441 0.500 CRWA1 R 15620
2.465 0.374 CRWA1 P 15624
2.502 0.313 CRWA1 R 15635

2.502 0.313 CRW1 R 15655
2.502 0.313 CRW1 V 15656
2.561 0.313 CRW1 R 15677
2.623 0.313 CRW1 R 15699

2.686 0.313 CRW1 R 15707
2.750 0.500 CRWH1 R 15761

2.875 0.313 CRW1 R 15773
2.875 0.313 CRWA1 P 15779

seal width
d1 D b
in. – –
1.578 2.082 0.250 CRW1 R 15510

2.408 0.313 CRWHA1 R 15557
1.594 2.125 0.313 CRW1 P 15915

2.2
2.437 0.313 CRW1 P 15940
2.437 0.313 CRW1 R 15955
2.502 0.313 CRW1 R 15960

2.623 0.313 CRW1 R 15968
2.758 0.313 CRW1 R 15975
1.618 2.531 0.438 CRWA1 R 16449
1.625 2.000 0.250 CRW1 V 16039

2.000 0.250 CRW1 R 160461)
2.116 0.313 CRWA1 R 16047

2.125 0.250 CRW1 V 16048
2.125 0.250 CRW1 R 16054
2.248 0.313 CRWA1 R 16062

2.250 0.313 CRW1 R 16061
2.250 0.313 CRW1 V 160781)
2.250 0.375 CRW1 P 16049
2.282 0.313 CRW1 R 16083
2.374 0.250 CRW1 R 160941)

2.374 0.313 CRWH1 R 16072
2.374 0.313 CRW1 V 16077
2.374 0.313 CRW1 R 16084

2.374 0.313 CRWA1 R 16085
2.374 0.313 CRWA1 P 160911)
2.374 0.500 CRWH1 R 16079
2.437 0.313 CRW1 R 16113

2.437 0.313 CRWA1 R 16128
2.437 0.313 CRW1 V 16119
2.437 0.313 CRWA1 V 16120
2.441 0.313 CRW1 R 16180

2.441 0.313 CRWA1 R 16201
2.502 0.313 CRWA1 V 16243

2.502 0.313 CRW1 R 16245
2.502 0.313 CRWA1 R 16246
2.502 0.313 CRWA1 P 162471)

2.502 0.374 CRWHA1 V 16257
2.502 0.375 CRWHA1 R 16254
2.562 0.313 CRWA1 V 16290
2.623 0.313 CRW1 R 16314

2.623 0.313 CRWA1 R 16315
2.623 0.313 CRW1 V 16316
2.686 0.313 CRW1 R 16337
2.686 0.313 CRW1 V 16338
2.750 0.250 CRW1 R 16364

2.750 0.313 CRWH1 R 16368
2.758 0.313 CRW1 R 16374
2.875 0.313 CRW1 R 16406

3.000 0.313 CRWH1 R 16422
1.645 2.656 0.313 CRWA1 P 16500
d1 1.656 – 1.813 in.
d1 D

seal width
d1 D b
in. – –
1.656 2.623 0.375 CRWA1 P 16545

2.686 0.313 CRW1 R 16556
1.688 2.279 0.500 CRWH1 R 16650

2.328 0.313 CRWA1 R 16657
2.437 0.250 CRW1 S 16692

2.437 0.313 CRW1 R 16679
2.437 0.313 CRWA1 R 16680
2.437 0.469 CRW1 S 16696
2.502 0.313 CRW1 R 16719

2.623 0.313 CRWA1 R 16814
2.623 0.500 CRW1 R 16816
2.623 0.500 CRWA1 V 16817
2.686 0.313 CRW1 R 16842
2.716 0.313 CRW1 R 16854

2.750 0.313 CRW1 R 169001)
2.750 0.375 CRWA1 R 16903
2.875 0.313 CRW1 R 16999
3.061 0.375 CRW1 R 17035

3.125 0.375 CRWA1 R 17038
1.704 3.034 0.500 CRWA1 R 17100
1.719 2.561 0.315 CRWA1 R 17144
1.750 2.250 0.313 CRW1 R 17231

2.250 0.313 CRW1 V 17234
2.374 0.313 CRWA1 V 17261

2.374 0.313 CRW1 R 17270
2.374 0.313 CRWA1 R 17271
2.411 0.375 CRW1 P 17280

2.437 0.313 CRW1 R 17283
2.437 0.313 CRW1 R 17284

seal width
d1 D b
in. – –
1.750 2.437 0.313 CRWA1 R 17285

cont. 2.437 0.313 CRW1 V 17292
2.437 0.313 CRWA1 V 17293 2.2
2.441 0.313 CRW1 R 17315
2.441 0.313 CRWA1 R 550154
2.441 0.375 CRWA1 V 17320
2.502 0.313 CRW1 V 17379

2.502 0.313 CRWA1 V 17381
2.502 0.313 CRW1 R 17386
2.502 0.313 CRWA1 R 17387
2.502 0.375 CRWHA1 V 17395

2.502 0.375 CRW1 S 17399
2.561 0.313 CRW1 R 17404
2.565 0.313 CRWA1 R 17413
2.623 0.313 CRW1 R 17442

2.623 0.313 CRWA1 R 17443
2.623 0.313 CRW1 S 17444
2.623 0.313 CRWA1 V 17448

2.623 0.375 CRWH1 R 17456
2.686 0.313 CRW1 R 174841)
2.717 0.438 CRWA1 R 17607

2.750 0.313 CRWA1 R 17523
2.750 0.313 CRW1 R 17557
2.750 0.313 CRW1 V 17558
2.758 0.313 CRW1 R 17605
2.810 0.313 CRWA1 R 176241)

2.810 0.313 CRWA1 V 17627
2.875 0.313 CRW1 R 17653
2.875 0.313 CRW1 V 17657
2.875 0.375 CRWHA1 R 17645
2.981 0.438 CRWHA1 R 176751)

2.997 0.313 CRWHA1 R 17678
2.997 0.313 CRW1 R 17695
3.000 0.313 CRWA1 R 17699

3.000 0.313 CRW1 R 17707
3.000 0.313 CRW1 V 17709
3.061 0.313 CRW1 R 17716

3.061 0.375 CRWA1 R 17718
3.189 0.313 CRW1 R 17746

3.543 0.438 CRW1 R 17756
3.625 0.438 CRW1 R 17761
1.768 2.363 0.313 CRWHA1 V 17780
1.781 2.252 0.313 CRWA1 R 17806

2.502 0.313 CRWH1 R 17810
2.502 0.313 CRWH1 V 17811
2.623 0.313 CRW1 R 17821

2.686 0.313 CRW1 R 178321)
1.812 2.623 0.374 CRWA1 V 17949
1.813 2.279 0.313 CRW1 R 18025

2.437 0.313 CRW1 R 18039
2.562 0.313 CRWA1 V 18049
d1 1.813 – 1.938 in.
d1 D

seal width
d1 D b
in. – –
1.813 2.623 0.313 CRW1 R 18104

cont.
2.686 0.313 CRWA1 P 18114
2.750 0.313 CRW1 R 18159

2.875 0.313 CRW1 R 18242
3.000 0.375 CRWA1 P 18264
1.844 2.623 0.313 CRW1 R 18425

2.750 0.313 CRW1 P 18444
1.868 2.518 0.315 CRWA1 P 18492
1.875 2.398 0.250 CRW1 R 18549

2.471 0.313 CRWA1 R 18545
2.500 0.313 CRW1 P 18555

2.502 0.313 CRW1 R 18565
2.562 0.313 CRWA1 V 18546
2.562 0.313 CRW1 P 18562
2.623 0.313 CRW1 R 18580

2.623 0.313 CRWA1 R 18581
2.623 0.313 CRW1 V 18582
2.623 0.313 CRWA1 V 18584

2.623 0.374 CRW1 S 18592
2.686 0.313 CRW1 R 18626
2.750 0.313 CRW1 V 18652

2.750 0.313 CRW1 R 18657
2.750 0.313 CRWA1 R 18658
2.750 0.313 CRW1 P 18666
2.758 0.313 CRW1 P 18671

2.758 0.313 CRW1 S 18679
2.782 0.438 CRWH1 R 18693
2.782 0.438 CRWHA1 R 18695
2.875 0.313 CRW1 V 18732

2.875 0.313 CRW1 R 18733
2.875 0.313 CRWA1 R 18734

seal width
d1 D b
in. – –
1.875 2.875 0.313 CRWA1 V 18737

cont. 2.997 0.313 CRW1 R 18785
3.000 0.313 CRW1 R 18817

2.2
3.000 0.313 CRW1 V 18818
3.061 0.313 CRWA1 R 18872
3.105 0.500 CRWA1 R 18880

3.189 0.469 CRWH1 R 18899
3.249 0.484 CRWA1 R 18922

3.371 0.438 CRWH1 R 18916
3.496 0.438 CRWA1 R 18924
3.500 0.438 CRW1 R 18926
1.893 2.434 0.250 CRW1 R 190001)
1.906 2.752 0.375 CRWA1 P 19017
1.915 2.533 0.250 CRW1 R 19010
1.938 2.412 0.313 CRW1 R 19215

2.437 0.250 CRW1 R 19210
2.437 0.250 CRW1 R 19212
2.502 0.375 CRWA1 R 19220

2.563 0.313 CRW1 R 19211
2.623 0.313 CRW1 R 19226

2.623 0.313 CRWA1 V 19227
2.623 0.313 CRWA1 R 19229
2.686 0.300 CRW1 P 19244

2.686 0.313 CRWA1 P 19234
2.686 0.313 CRW1 R 19236
2.686 0.313 CRWA1 R 19237

2.686 0.313 CRWA1 V 19243
2.686 0.375 CRW1 S 19240
2.750 0.313 CRW1 R 19264

2.750 0.313 CRW1 V 19267
2.875 0.313 CRW1 R 19300

2.875 0.313 CRWA1 R 19301
2.875 0.313 CRWH1 V 19304
2.884 0.313 CRWA1 P 19310

2.997 0.313 CRW1 R 19350
3.000 0.313 CRW1 R 19359

3.000 0.313 CRWA1 R 193601)
3.000 0.313 CRWA1 V 19368
3.061 0.313 CRW1 R 19380

3.062 0.500 CRW1 S 19438
3.125 0.500 CRW1 R 19400

3.189 0.313 CRW1 R 19407
3.251 0.313 CRWA1 V 19433

3.251 0.313 CRW1 R 19434
3.350 0.469 CRWHA1 R 19445

3.543 0.313 CRW1 R 19449
d1 1.969 – 2.125 in.
d1 D

seal width
d1 D b
in. – –
1.969 2.623 0.313 CRWA1 R 19607
2.000 2.500 0.438 CRW1 S 19739

2.502 0.313 CRW1 P 19745
2.623 0.313 CRW1 R 19760

2.623 0.313 CRWA1 R 19762
2.623 0.313 CRWA1 V 19777
2.623 0.313 CRWA1 V 19782
2.686 0.375 CRW1 R 19778
2.716 0.375 CRW1 R 19785

2.716 0.375 CRWA1 R 19786
2.746 0.375 CRW1 S 19807
2.750 0.313 CRW1 V 19823
2.750 0.313 CRW1 R 19831

2.750 0.313 CRWA1 R 19832
2.750 0.313 CRWA1 V 19839
2.750 0.313 CRW1 V 19840
2.835 0.469 CRWH1 R 19848

2.875 0.313 CRW1 V 19884
2.875 0.313 CRW1 R 19886
2.875 0.313 CRWA1 R 19887

2.875 0.375 CRWHA1 R 19896
2.875 0.500 CRWH1 R 19900
2.880 0.375 CRWA1 R 19922

2.880 0.375 CRWA1 P 19923
2.997 0.375 CRWH1 R 19969

2.997 0.375 CRWHA1 R 19970
2.997 0.375 CRWH1 V 19979
3.000 0.313 CRW1 R 19992

3.000 0.313 CRWA1 R 19993
3.000 0.313 CRWA1 V 19995

seal width
d1 D b
in. – –
2.000 3.000 0.375 CRWH1 V 20002

cont. 3.000 0.375 CRWH1 R 20004
3.000 0.375 CRWHA1 R 20005 2.2
3.061 0.375 CRW1 R 20045
3.061 0.500 CRWH1 R 20055
3.061 0.500 CRWHA1 R 20059
3.125 0.375 CRW1 R 20070

3.150 0.375 CRW1 R 20079
3.189 0.469 CRWH1 R 20098
3.189 0.469 CRWHA1 R 20100
3.251 0.438 CRWH1 R 20109
3.371 0.438 CRW1 V 20122

3.371 0.438 CRWH1 R 20124
3.371 0.438 CRWHA1 R 20125
3.371 0.438 CRWH1 V 201271)
3.543 0.438 CRWH1 R 20140

3.623 0.438 CRWH1 R 20144
4.003 0.438 CRWH1 R 20158
2.047 2.561 0.315 CRW1 R 20420
2.063 2.561 0.313 CRW1 V 20520

2.750 0.313 CRWH1 R 205301)
2.842 0.438 CRWH1 R 20538

2.875 0.438 CRWH1 R 20554
2.997 0.438 CRWH1 R 20586
3.000 0.375 CRW1 R 20594

3.000 0.375 CRWA1 V 20596
3.061 0.313 CRWH1 R 20643
3.125 0.375 CRW1 R 20659

3.189 0.375 CRW1 R 20702
3.251 0.438 CRWHA1 R 20747

3.251 0.438 CRWH1 R 20749
2.125 2.750 0.375 CRW1 V 210631)

2.750 0.500 CRWA1 R 21061
2.763 0.250 CRW1 R 21069
2.875 0.375 CRW1 S 21103

2.875 0.438 CRW1 V 21091
2.875 0.438 CRW1 R 21098
2.875 0.438 CRWA1 R 21100
2.875 0.438 CRWHA1 R 21108
2.997 0.438 CRWH1 R 21134

2.997 0.438 CRWHA1 R 21136
3.000 0.313 CRWHA1 V 21167

3.000 0.375 CRW1 R 21163
3.000 0.375 CRWA1 R 21164
3.000 0.438 CRWH1 V 21171

3.000 0.438 CRWH1 R 21172
3.000 0.438 CRWHA1 R 21173
d1 2.125 – 2.328 in.
d1 D

seal width
d1 D b
in. – –
2.125 3.061 0.438 CRWH1 V 21215

cont.
3.061 0.500 CRW1 R 21210
3.061 0.500 CRWA1 R 212111)
3.061 0.500 CRWHA1 R 21213
3.125 0.438 CRWH1 R 21234

3.125 0.438 CRWHA1 P 21245
3.189 0.375 CRWA1 R 21267

3.189 0.375 CRWA1 V 21269
3.189 0.469 CRWHA1 S 21270
3.251 0.438 CRWH1 R 21302
3.350 0.438 CRWH1 R 21336

3.371 0.375 CRWA1 R 21352
3.371 0.438 CRWH1 R 21353
3.543 0.438 CRWH1 R 21358
2.188 2.875 0.438 CRWH1 R 21736

2.997 0.438 CRWH1 R 21749
3.000 0.375 CRWA1 R 21759

3.000 0.375 CRWA1 V 21763
3.000 0.500 CRWH1 R 21764
3.061 0.500 CRWH1 R 21787
3.251 0.438 CRWH1 R 21840

3.350 0.438 CRWH1 R 21890
3.371 0.438 CRWH1 R 21910
2.250 2.875 0.313 CRWA1 R 22328

2.891 0.563 CRWA1 R 22347
2.997 0.438 CRWH1 R 22336

2.997 0.438 CRWHA1 R 22340
3.000 0.375 CRW1 R 22353

3.000 0.375 CRWA1 R 22354
3.000 0.375 CRWA1 V 22361
3.000 0.375 CRW1 V 22363

seal width
d1 D b
in. – –
2.250 3.000 0.438 CRWH1 R 22358

cont. 3.000 0.438 CRWHA1 R 22359
3.000 0.438 CRWH1 V 22367 2.2
3.061 0.375 CRW1 R 22382
3.061 0.438 CRWH1 R 22390
3.061 0.438 CRWHA1 R 22391
3.061 0.438 CRWHA1 S 22394
3.125 0.375 CRWA1 R 22400

3.125 0.375 CRWA1 V 22405
3.125 0.500 CRWH1 R 224071)
3.189 0.438 CRW1 R 22424

3.189 0.438 CRWA1 P 22425
3.251 0.375 CRW1 R 22440

3.251 0.375 CRWA1 R 22441
3.251 0.438 CRWH1 R 22446

3.251 0.438 CRWHA1 R 22448
3.251 0.438 CRWH1 V 22449
3.350 0.375 CRW1 P 22484

3.350 0.438 CRWH1 R 224921)
3.350 0.438 CRWHA1 R 22493
3.350 0.438 CRWH1 V 22495
3.371 0.438 CRWHA1 R 22532

3.371 0.438 CRWH1 R 22558
3.371 0.438 CRWH1 V 22561
3.500 0.438 CRWHA1 R 22582

3.500 0.438 CRWH1 R 22583
3.500 0.438 CRWHA1 V 22590
3.565 0.438 CRWA1 R 22610
3.623 0.438 CRWH1 R 22618

3.623 0.438 CRWHA1 R 22619
3.751 0.438 CRWH1 R 22626

3.876 0.438 CRWH1 R 22644
4.003 0.438 CRWH1 R 22647
2.313 2.997 0.375 CRW1 R 23030

3.000 0.438 CRWH1 V 23040
3.061 0.313 CRW1 R 23046
3.125 0.375 CRW1 R 23061

3.125 0.375 CRWA1 V 23063
3.251 0.438 CRWH1 R 23093

3.251 0.438 CRWHA1 V 230991)
3.350 0.438 CRWH1 R 23152

3.371 0.438 CRW1 R 23167
3.374 0.438 CRWHA1 R 23169
3.500 0.313 CRW1 R 231841)

3.751 0.500 CRW1 R 23277
2.328 3.000 0.395 CRW1 P 23300
d1 2.375 – 2.500 in.
d1 D

seal width
d1 D b
in. – –
2.375 2.997 0.438 CRWH1 R 23632

3.000 0.375 CRW1 V 23641
3.061 0.438 CRWH1 R 23644

3.061 0.438 CRWH1 P 23645
3.061 0.438 CRWH1 V 23655
3.125 0.375 CRW1 R 23646

3.125 0.438 CRWH1 R 23652
3.125 0.438 CRWHA1 R 23654
3.125 0.438 CRWHA1 V 23656
3.189 0.438 CRWH1 R 23666
3.251 0.438 CRWHA1 V 23678

3.251 0.453 CRW1 P 23685
3.350 0.375 CRW1 R 23701

3.350 0.375 CRWA1 R 23702
3.350 0.375 CRW1 P 23703
3.350 0.375 CRW1 S 23706

3.350 0.438 CRWH1 R 23708
3.350 0.438 CRWHA1 R 23710
3.371 0.438 CRWH1 R 23742

3.371 0.438 CRWH1 V 23746
3.481 0.438 CRWH1 R 23755

3.481 0.438 CRWHA1 R 237561)
3.500 0.375 CRWA1 P 23770

3.500 0.375 CRWH1 V 23771
3.500 0.375 CRWH1 R 23779
3.500 0.438 CRWHA1 R 23782
3.543 0.438 CRWH1 R 23808

3.543 0.438 CRWHA1 V 23809
3.601 0.438 CRW1 R 23820

3.623 0.438 CRWH1 R 23839

seal width
d1 D b
in. – –
2.375 3.623 0.438 CRWHA1 P 23841

cont. 3.623 0.438 CRWHA1 V 23843
3.876 0.438 CRWH1 R 23844 2.2
2.438 3.125 0.500 CRWH1 R 24255
3.251 0.438 CRWH1 R 24263
3.350 0.375 CRW1 R 24286

3.350 0.375 CRWA1 R 24287
3.371 0.438 CRWH1 R 24320

3.481 0.438 CRWH1 R 24340
3.500 0.438 CRWH1 R 24370

3.500 0.438 CRWH1 V 24372
3.543 0.438 CRWH1 R 24445
2.500 3.189 0.438 CRWH1 R 24881

3.189 0.438 CRWH1 V 24883
3.245 0.438 CRWH1 R 24889
3.251 0.375 CRW1 R 24897

3.251 0.375 CRWA1 R 24898
3.251 0.375 CRWA1 V 24899
3.251 0.438 CRWH1 R 24910
3.251 0.438 CRWHA1 R 24911

3.251 0.438 CRWH1 V 24914
3.251 0.438 CRWHA1 V 24916
3.251 0.500 CRW1 V 24913
3.350 0.438 CRWH1 R 24931

3.350 0.438 CRWHA1 R 24932
3.371 0.375 CRWHA1 R 249341)

3.371 0.438 CRWHA1 V 24936
3.371 0.438 CRWH1 R 24954
3.428 0.375 CRWA1 P 24949

3.428 0.375 CRWA1 R 24951
3.500 0.375 CRWA1 V 24971

3.500 0.438 CRW1 R 24980
3.500 0.438 CRWA1 R 24982
3.500 0.438 CRWH1 V 24984
3.500 0.438 CRWH1 R 24986

3.500 0.438 CRWHA1 R 24988
3.500 0.438 CRWH1 P 24989
3.500 0.438 CRWHA1 V 24990
3.502 0.406 CRW1 S 25082

3.543 0.438 CRWH1 R 25043
3.543 0.438 CRWHA1 P 250651)
3.544 0.433 CRWA1 V 25037
3.623 0.375 CRW1 R 25074

3.623 0.375 CRWA1 R 25075
3.623 0.375 CRWA1 V 25076
3.623 0.438 CRWH1 R 250711)
3.751 0.438 CRWH1 R 250911)

3.876 0.438 CRWH1 R 25100
3.876 0.469 CRWHA1 P 25102
4.003 0.375 CRWA1 R 25108

4.003 0.375 CRWA1 V 25110
d1 2.563 – 2.750 in.
d1 D

seal width
d1 D b
in. – –
2.563 3.481 0.500 CRWHA1 R 25561

3.500 0.438 CRWH1 R 25597
3.623 0.438 CRWH1 R 25641

3.623 0.469 CRWA1 P 25661
3.751 0.438 CRWH1 R 25713

3.751 0.438 CRWHA1 R 25714
3.751 0.438 CRWH1 V 25725
3.873 0.438 CRWHA1 R 257451)

3.876 0.438 CRWH1 R 25748
2.598 3.481 0.438 CRWHA1 P 25970
2.607 3.350 0.375 CRWH1 P 25950
2.625 3.251 0.438 CRWH1 R 26110

3.350 0.375 CRW1 V 26122
3.350 0.375 CRW1 R 26123
3.350 0.375 CRWA1 R 26124
3.350 0.438 CRW1 R 261281)
3.371 0.438 CRWHA1 R 26153

3.374 0.438 CRWHA1 R 26141
3.481 0.438 CRWH1 R 26163
3.500 0.375 CRW1 V 26177

3.500 0.375 CRWA1 R 26186
3.500 0.438 CRWH1 R 26189
3.500 0.438 CRWHA1 R 26190
3.500 0.438 CRWA1 P 26191

3.543 0.438 CRWH1 R 26194
3.623 0.375 CRW1 V 26204

3.623 0.375 CRWA1 P 26220
3.623 0.375 CRW1 R 26237

seal width
d1 D b
in. – –
2.625 3.623 0.375 CRWA1 R 26238

cont.
3.623 0.438 CRWH1 V 26208

3.623
3.623
0.438
0.438
CRWH1 R
CRWHA1 R
26209
26211
2.2
3.751 0.375 CRWA1 R 26284
3.751 0.438 CRWH1 R 26297
3.751 0.438 CRWHA1 R 26298

3.751 0.438 CRWHA1 V 26299
3.876 0.438 CRWH1 R 26328

3.936 0.438 CRWH1 R 26346
4.003 0.375 CRWA1 R 26354

4.003 0.438 CRWH1 R 26356
4.370 0.438 CRWHA1 R 26359

4.438 0.438 CRWH1 R 26368
2.688 3.751 0.438 CRWH1 R 26761

3.876 0.438 CRWH1 R 26921
4.003 0.469 CRWH1 R 26975
2.750 3.481 0.438 CRW1 R 272511)

3.500 0.375 CRW1 R 27268
3.500 0.375 CRWA1 R 27269

3.500 0.375 CRWA1 V 27272
3.500 0.438 CRWH1 R 27280
3.538 0.438 CRWH1 R 27284
3.543 0.438 CRWH1 P 27292

3.543 0.438 CRWH1 V 27293
3.543 0.438 CRWHA1 P 27295
3.623 0.438 CRWH1 V 27324

3.623 0.438 CRWH1 R 27334
3.751 0.438 CRW1 R 27361

3.751 0.438 CRWA1 R 27362
3.751 0.438 CRWH1 V 27365
3.751 0.438 CRWH1 R 27368

3.751 0.438 CRWHA1 R 27370
3.751 0.438 CRWA1 P 27377
3.765 0.438 CRWH1 R 27426
3.876 0.433 CRWHA1 P 27452

3.876 0.438 CRWA1 R 27467
3.876 0.438 CRWH1 R 27470
3.876 0.438 CRWHA1 R 27471
3.936 0.438 CRWH1 R 27525

3.937 0.438 CRWA1 P 27526
4.003 0.375 CRWA1 V 27539

4.003 0.438 CRWH1 R 27541
4.003 0.438 CRWHA1 P 275651)
4.249 0.438 CRWH1 R 27600

4.249 0.438 CRWHA1 P 27601
4.331 0.500 CRWHA1 R 27625

4.500 0.469 CRWH1 R 28848
d1 2.813 – 3.125 in.
d1 D

seal width
d1 D b
in. – –
2.813 3.751 0.438 CRWH1 R 28035

3.876 0.438 CRWH1 R 28116
4.003 0.438 CRWH1 R 28175

4.249 0.313 CRW1 R 28270
4.249 0.438 CRWH1 R 28275
4.250 0.438 CRWH1 P 28276
2.844 3.939 0.500 CRWA1 R 28425

3.939 0.550 CRWHA1 R 28426
4.003 0.438 CRWH1 R 28464

4.003 0.500 CRWH1 V 28474
2.875 3.623 0.438 CRWH1 R 28654

3.623 0.438 CRWHA1 R 28655
3.751 0.375 CRWA1 R 28669

3.751 0.375 CRWA1 V 28670
3.751 0.438 CRWH1 R 28686
3.751 0.438 CRWHA1 R 28687

3.751 0.438 CRWH1 P 28697
3.751 0.438 CRWH1 V 28698
3.751 0.438 CRWHA1 V 28699
3.876 0.438 CRWH1 R 28745

3.876 0.438 CRWHA1 R 28746
3.876 0.438 CRWHA1 V 28748
4.003 0.375 CRWA1 R 28778

4.003 0.375 CRWA1 V 28779
4.003 0.438 CRWH1 R 28760
4.003 0.438 CRWHA1 R 28761
4.125 0.375 CRWH1 R 28817

4.331 0.438 CRWA1 P 28841

seal width
d1 D b
in. – –
2.938 3.623 0.375 CRW1 R 29218

3.751 0.375 CRW1 R 29223

3.751
3.751
0.375
0.375
CRWA1 R
CRWA1 V
29224
29226
2.2
3.876 0.375 CRWHA1 R 292631)
3.876 0.375 CRWHA1 V 29262
3.937 0.438 CRWA1 P 29273
4.003 0.438 CRWH1 R 29316

4.003 0.438 CRWHA1 R 293931)
4.003 0.438 CRWA1 P 29350
4.004 0.433 CRWHA1 V 29383
4.125 0.375 CRWH1 R 29184

4.125 0.375 CRWHA1 R 29385
4.501 0.438 CRWH1 R 29465
3.000 3.500 0.375 CRW1 V 29841

3.751 0.375 CRW1 R 298651)
3.751 0.375 CRWA1 R 29866
3.751 0.375 CRWA1 P 29867
3.751 0.375 CRW1 V 29868

3.751 0.375 CRWA1 V 29870
3.751 0.438 CRWH1 R 29871
3.751 0.438 CRWHA1 R 29872
3.876 0.313 CRW1 V 29877

3.876 0.438 CRWH1 R 29887
3.876 0.469 CRWH1 V 29891
4.003 0.375 CRW1 R 29906

4.003 0.375 CRWA1 R 29907
4.003 0.375 CRWA1 V 29912
4.003 0.375 CRWH1 P 29950
4.003 0.438 CRWHA1 P 299251)

4.003 0.438 CRWH1 R 299511)
4.003 0.438 CRWHA1 R 29952
4.003 0.438 CRWH1 V 29958
4.125 0.438 CRWH1 R 30000

4.125 0.438 CRWH1 V 30003
4.249 0.438 CRWH1 R 300331)

4.249 0.438 CRWHA1 P 30056
4.331 0.438 CRWH1 R 30060
4.376 0.438 CRWH1 R 30070
4.500 0.438 CRWH1 R 30087

4.500 0.438 CRWHA1 R 30095
4.501 0.438 CRWH1 V 30098
4.999 0.438 CRWH1 R 30125
3.125 3.811 0.355 CRW1 V 31132

3.811 0.355 CRW1 R 31135
4.003 0.375 CRWA1 R 31139

4.003 0.375 CRWHA1 V 31152
4.003 0.438 CRWH1 R 31147
4.003 0.438 CRWHA1 R 31148
d1 3.125 – 3.500 in.
d1 D

seal width
d1 D b
in. – –
3.125 4.125 0.375 CRW1 R 31177

cont.
4.125 0.375 CRWA1 V 31179
4.125 0.438 CRWHA1 P 31173
4.125 0.438 CRWHA1 S 31185
4.125 0.438 CRWH1 R 311891)
4.249 0.438 CRWH1 R 31227

4.249 0.438 CRWHA1 R 31228
4.249 0.438 CRWHA1 V 31237
4.376 0.438 CRWH1 R 31250

4.376 0.438 CRWHA1 P 31261
4.501 0.438 CRWH1 R 31269

4.626 0.438 CRWH1 R 31299
4.751 0.438 CRWH1 R 31327
4.999 0.438 CRWH1 R 31333
5.251 0.438 CRWH1 R 31353
3.150 3.946 0.394 CRW1 V 31511
3.188 4.249 0.438 CRWH1 R 31758

4.376 0.438 CRWH1 R 31825
4.501 0.438 CRWH1 R 31855
4.626 0.438 CRWH1 R 31870
4.999 0.438 CRWH1 R 31955
3.250 3.876 0.375 CRW1 P 32330

4.003 0.375 CRW1 R 32344
4.003 0.375 CRWA1 P 32347
4.249 0.375 CRWA1 V 32392

4.249 0.375 CRW1 R 32393
4.249 0.375 CRWA1 R 32395
4.249 0.438 CRWH1 P 323801)
4.249 0.438 CRWHA1 P 32385

4.249 0.438 CRWH1 R 32396
4.249 0.438 CRWHA1 R 32397
4.249 0.438 CRWH1 V 32403

seal width
d1 D b
in. – –
3.250 4.376 0.438 CRWH1 R 32424

cont. 4.500 0.438 CRWA1 P 32448
4.501 0.375 CRW1 R 32477

2.2
4.501 0.438 CRWH1 R 32501
4.501 0.438 CRWHA1 R 32502
4.626 0.433 CRWHA1 R 325141)

4.626 0.438 CRWH1 R 32540
4.718 0.438 CRWH1 R 32555

4.751 0.438 CRWH1 R 32560
4.999 0.438 CRWH1 R 32582

4.999 0.438 CRWHA1 R 32583
3.313 4.125 0.438 CRWH1 R 33033

4.249 0.438 CRWH1 R 33073
4.500 0.438 CRWH1 R 33136
4.999 0.438 CRWH1 R 33306
3.375 4.125 0.375 CRW1 R 33645

4.125 0.375 CRWA1 V 34647
4.249 0.438 CRWHA1 R 33665

4.280 0.406 CRWA1 S 33654
4.376 0.375 CRWA1 V 33699

4.376 0.375 CRW1 R 33700
4.376 0.375 CRWA1 R 33701
4.376 0.438 CRWH1 R 33711
4.376 0.438 CRWHA1 R 33712
4.501 0.438 CRWA1 V 33733

4.501 0.438 CRWH1 R 33735
4.626 0.438 CRWH1 R 33772

4.626 0.438 CRWHA1 R 33773
4.626 0.438 CRWHA1 V 33775
4.686 0.438 CRWH1 R 338071)
4.999 0.438 CRWH1 R 338371)

5.251 0.438 CRWHA1 R 33866
3.438 4.249 0.375 CRW1 R 34256

4.501 0.375 CRWA1 R 34279
4.501 0.438 CRWH1 R 34282
4.501 0.438 CRWHA1 R 34283
4.626 0.438 CRWH1 R 34336

4.626 0.438 CRWHA1 R 34338
4.751 0.438 CRWA1 R 34379

4.756 0.438 CRWH1 R 34383
4.876 0.438 CRWH1 R 34398
4.999 0.438 CRWH1 R 34407

4.999 0.438 CRWHA1 R 34408
3.500 4.249 0.438 CRWHA1 V 34857

4.376 0.375 CRW1 R 34860
4.376 0.375 CRWA1 R 34861
4.376 0.375 CRWA1 V 34866

4.376 0.433 CRWHA1 V 34869
4.376 0.438 CRWH1 R 34867
4.376 0.438 CRWHA1 R 34868
d1 3.500 – 3.875 in.
d1 D

seal width
d1 D b
in. – –
3.500 4.501 0.375 CRWA1 V 34883

cont.
4.501 0.375 CRW1 R 34886
4.501 0.375 CRWA1 R 34887
4.501 0.438 CRWH1 R 34888
4.501 0.438 CRWHA1 R 34889

4.501 0.438 CRWHA1 P 348911)
4.501 0.438 CRWH1 V 34892
4.626 0.438 CRWH1 R 34985
4.751 0.375 CRWA1 V 35039

4.751 0.375 CRWA1 P 35040
4.751 0.438 CRWH1 R 35012
4.751 0.438 CRWHA1 R 35020
4.751 0.625 CRWH1 R 35029
4.999 0.438 CRWA1 V 35080

4.999 0.438 CRWH1 R 35082
4.999 0.438 CRWHA1 P 35083
5.126 0.438 CRWH1 R 35086

5.126 0.438 CRWHA1 R 35095
5.251 0.438 CRWH1 R 35096
3.563 4.501 0.438 CRWH1 R 35556

4.626 0.438 CRWH1 R 35593
4.751 0.438 CRWH1 R 35649
4.876 0.438 CRWH1 R 35676
4.999 0.438 CRWH1 R 35716
3.625 4.376 0.375 CRWA1 V 36153

4.376 0.375 CRWA1 R 36155
4.376 0.375 CRWH1 R 36157
4.376 0.375 CRWH1 P 36158
4.501 0.375 CRW1 R 36166

seal width
d1 D b
in. – –
3.625 4.626 0.375 CRW1 R 36177

cont. 4.626 0.375 CRWA1 V 36179

4.626
4.626
0.438
0.438
CRWH1 R
CRWHA1 R
36185
36186
2.2
4.751 0.438 CRWH1 R 36220
4.751 0.500 CRWA1 S 36234
4.876 0.438 CRWH1 R 36314
4.999 0.375 CRWA1 V 36359

4.999 0.375 CRWA1 R 36361
4.999 0.438 CRWH1 R 36363
4.999 0.438 CRWHA1 R 36364
5.251 0.375 CRWA1 R 36382

5.375 0.438 CRWHA1 R 36391
3.688 4.501 0.438 CRWHA1 R 36740

4.751 0.438 CRWH1 R 36770
4.999 0.438 CRWH1 R 36880
5.126 0.438 CRWA1 R 36895

5.626 0.438 CRWA1 R 36910
3.750 4.501 0.375 CRW1 R 373271)

4.501 0.375 CRW1 V 37328
4.501 0.469 CRWHA1 P 37330
4.502 0.469 CRWHA1 V 37332
4.750 0.438 CRWHA1 P 37403

4.751 0.375 CRW1 P 37387
4.751 0.375 CRW1 R 37388
4.751 0.375 CRWA1 R 37389
4.751 0.438 CRWA1 P 37390

4.751 0.438 CRWHA1 S 37395
4.751 0.438 CRWH1 R 37396
4.751 0.438 CRWH1 V 37405
4.876 0.438 CRWH1 R 37433

4.999 0.375 CRW1 V 37524
4.999 0.375 CRW1 R 37525
4.999 0.375 CRWA1 R 37526

4.999 0.438 CRWH1 R 37532
4.999 0.438 CRWHA1 R 37533
5.251 0.438 CRWH1 R 37574

5.251 0.438 CRWH1 V 37577
3.875 4.751 0.375 CRW1 R 38646

4.751 0.375 CRWA1 R 38647
4.751 0.375 CRWA1 V 38649
4.751 0.438 CRWH1 R 38653
4.876 0.438 CRWHA1 R 38673

4.876 0.500 CRWH1 R 38669
4.876 0.500 CRWHA1 V 38678
4.999 0.375 CRW1 R 38691

4.999 0.375 CRWA1 R 38692
4.999 0.375 CRWA1 V 38694
5.126 0.438 CRWHA1 V 38702

5.126 0.438 CRWH1 R 38703
5.126 0.438 CRWHA1 R 38713
d1 3.875 – 4.477 in.
d1 D

seal width
d1 D b
in. – –
3.875 5.251 0.438 CRWH1 R 38730

cont.
5.251 0.438 CRWHA1 R 38731
5.251 0.438 CRWHA1 P 38739
5.376 0.438 CRWH1 R 38745

5.626 0.433 CRWHA1 R 38758
5.690 0.500 CRWH1 R 38774
3.938 4.876 0.438 CRWH1 R 39245

4.999 0.438 CRWH1 R 39275
4.999 0.438 CRWH1 V 39276
4.999 0.438 CRWH1 R 39277
5.126 0.472 CRWHA1 V 39304

5.251 0.438 CRWH1 R 39320
5.375 0.438 CRWH1 R 39350
5.501 0.438 CRWH1 R 39423
4.000 4.876 0.438 CRW1 R 39851

4.999 0.375 CRW1 P 39895
4.999 0.375 CRWA1 V 39921
4.999 0.375 CRW1 R 39922

4.999 0.375 CRWA1 R 39923
4.999 0.438 CRWHA1 P 39930
4.999 0.438 CRWH1 V 39932
4.999 0.438 CRWH1 R 39933

4.999 0.438 CRWHA1 R 39934
4.999 0.438 CRWH1 S 39935
5.126 0.438 CRWH1 R 39975

5.251 0.438 CRWH1 V 39996
5.251 0.438 CRWH1 R 39997
5.251 0.438 CRWA1 R 40000
5.310 0.500 CRWHA1 R 40020

5.376 0.438 CRWH1 R 40036
5.501 0.438 CRWH1 R 40049

seal width
d1 D b
in. – –
4.000 5.626 0.375 CRWA1 R 40077

cont. 5.626 0.438 CRWH1 R 40078
5.751 0.438 CRWH1 R 40108 2.2
6.001 0.500 CRWH1 R 40138
6.250 0.500 CRWH1 R 40158
4.125 4.999 0.438 CRWH1 R 41125

4.999 0.438 CRWH1 V 411261)
5.126 0.438 CRWH1 R 41170

5.126 0.438 CRWH1 V 41171
5.251 0.438 CRWH1 R 41185

5.251 0.438 CRWH1 V 41186
5.501 0.438 CRWH1 R 41265

5.501 0.438 CRWH1 V 41266
5.751 0.438 CRWH1 R 41287

6.001 0.438 CRWH1 R 41305
6.001 0.438 CRWH1 V 41307
4.250 5.251 0.375 CRWA1 R 42419

5.251 0.375 CRW1 S 42422
5.251 0.438 CRWH1 R 42426

5.251 0.438 CRWHA1 R 42427
5.251 0.438 CRWH1 V 42433
5.373 0.438 CRWA1 V 42474

5.376 0.438 CRWH1 R 42475
5.501 0.438 CRWH1 R 42528

5.626 0.438 CRWA1 R 42557
5.751 0.438 CRWH1 R 42573
5.876 0.500 CRWH1 V 42592
6.001 0.500 CRWH1 R 42616

6.126 0.500 CRWH1 R 42635
6.250 0.500 CRWH1 R 42644
4.313 5.501 0.433 CRWHA1 P 43072

5.501 0.438 CRWHA1 R 43073
4.331 5.626 0.472 CRWHA1 V 43345
4.375 5.376 0.438 CRWH1 R 43650

5.501 0.438 CRWH1 R 43691
5.751 0.438 CRWH1 R 43751
6.001 0.500 CRWH1 R 43771

6.063 0.500 CRWH1 R 5419741)
6.250 0.500 CRWH1 R 43820
4.438 5.501 0.500 CRWH1 R 44275

5.501 0.500 CRWH1 V 44276
5.751 0.500 CRWH1 R 44295
6.001 0.500 CRWH1 R 44320

6.250 0.500 CRWH1 R 44350
4.477 6.250 0.500 CRWH1 R 44630
d1 4.500 – 5.125 in.
d1 D

seal width
d1 D b
in. – –
4.500 5.251 0.438 CRWH1 R 44913

5.251 0.438 CRWHA1 V 44917
5.376 0.438 CRWH1 R 44920

5.376 0.438 CRWHA1 V 44926
5.501 0.375 CRW1 R 44959

5.501 0.375 CRWA1 R 44960
5.501 0.435 CRWH1 V 44980
5.501 0.438 CRWH1 R 44967

5.501 0.438 CRWHA1 R 44968
5.501 0.438 CRWH1 V 44973
5.626 0.438 CRWH1 R 45032

5.626 0.438 CRWHA1 V 45033
5.751 0.375 CRWA1 V 45064

5.751 0.438 CRWH1 R 45069
5.751 0.438 CRWHA1 R 45070
6.001 0.500 CRWH1 R 45110

6.001 0.500 CRWHA1 R 45111
6.001 0.500 CRWHA1 V 45112
6.126 0.563 CRWH1 R 45140

6.250 0.500 CRWH1 R 45150
4.625 5.626 0.500 CRWH1 R 46144

5.626 0.500 CRWH1 V 46155
5.751 0.500 CRWH1 R 46200

5.751 0.500 CRWH1 S 46208
6.001 0.500 CRWH1 R 46285

6.250 0.500 CRWH1 R 46324
4.688 5.751 0.512 CRWH1 S 46770

5.751 0.512 CRWH1 R 46800
6.250 0.500 CRWH1 R 46950

seal width
d1 D b
in. – –
4.750 5.749 0.438 CRW1 P 47375

5.751 0.500 CRW1 V 47379

5.751
5.751
0.500
0.500
CRWA1 V
CRW1 R
47382
47383
2.2
5.751 0.500 CRWH1 R 47394
5.751 0.500 CRWHA1 R 47395
5.875 0.500 CRWH1 R 47441
6.001 0.500 CRWH1 R 47474

6.001 0.500 CRWHA1 R 47475
6.001 0.500 CRW1 V 47481
6.250 0.500 CRWH1 R 47583

6.250 0.500 CRWHA1 V 47586
4.813 5.751 0.563 CRWH1 P 48060

5.751 0.563 CRWH1 V 48062
5.751 0.563 CRWH1 S 48065
4.875 6.001 0.500 CRWH1 V 48692

6.001 0.500 CRWH1 R 48693
6.126 0.500 CRWH1 R 48726
6.250 0.500 CRWHA1 R 48768

6.250 0.500 CRWH1 R 48769
6.250 0.500 CRWH1 V 48772
4.921 6.375 0.500 CRWHA1 V 49274
4.938 6.001 0.500 CRWH1 R 49251

6.250 0.500 CRWH1 R 49301
5.000 6.001 0.500 CRWHA1 V 49927

6.001 0.500 CRWH1 R 49928
6.001 0.500 CRWHA1 R 49929
6.126 0.500 CRW1 V 49960
6.250 0.500 CRWH1 R 49966

6.250 0.500 CRW1 R 49984
6.250 0.500 CRWA1 R 49985
6.250 0.500 CRWH1 P 499901)

6.250 0.500 CRWH1 V 49991
6.250 0.500 CRWHA1 R 49998
6.375 0.500 CRWH1 R 50130

6.375 0.500 CRWHA1 R 50138
6.500 0.500 CRWH1 R 50148

6.500 0.500 CRWH1 V 50151
6.750 0.500 CRWH1 R 50168

6.750 0.500 CRWHA1 R 50172
5.063 6.126 0.500 CRWH1 R 50618

6.375 0.500 CRWH1 R 50650
5.125 6.126 0.500 CRWHA1 R 51240

6.126 0.500 CRW1 V 51243
6.126 0.500 CRW1 R 51247
6.250 0.500 CRWHA1 R 51252

6.250 0.500 CRWA1 V 51253
6.375 0.500 CRWH1 R 512481)

6.375 0.500 CRWH1 V 51255
d1 5.188 – 7.000 in.
d1 D

seal width
d1 D b
in. – –
5.188 6.501 0.625 CRWH1 V 51852
5.250 6.001 0.375 CRW1 R 52440

6.001 0.500 CRWH1 V 52443
6.250 0.500 CRWH1 R 52445

6.250 0.500 CRWH1 V 52447
6.500 0.500 CRWH1 R 52488

6.500 0.500 CRWH1 V 52489
6.750 0.500 CRWH1 R 52648

6.750 0.500 CRWH1 V 52649
5.375 6.625 0.500 CRWH1 R 53701

6.625 0.500 CRWH1 V 53702
6.750 0.500 CRWH1 V 53771

6.750 0.500 CRWH1 R 53775
5.500 6.250 0.500 CRWA1 R 54925

6.500 0.500 CRWH1 R 54931
6.500 0.500 CRWH1 V 54934
6.500 0.500 CRWH1 P 54936
6.750 0.500 CRW1 R 54959

6.750 0.500 CRWA1 R 54960
6.750 0.500 CRWHA1 R 54971
6.750 0.500 CRWH1 R 54972
6.750 0.500 CRWH1 V 54974
5.512 6.693 0.472 CRWH1 V 5467471)
5.625 6.625 0.500 CRWH1 R 56101

6.625 0.500 CRWH1 V 56102
6.875 0.500 CRWH1 R 56136

6.875 0.500 CRWH1 V 56137

seal width
d1 D b
in. – –
5.625 7.125 0.500 CRWHA1 R 56160

cont. 7.125 0.500 CRWHA1 V 56161
5.750 6.625 0.500 CRWH1 R 57505

2.2
6.625 0.500 CRW1 V 57506
6.750 0.500 CRWH1 R 57510

6.750 0.500 CRWH1 V 57522
6.751 0.500 CRWHA1 R 575091)
7.000 0.500 CRWH1 R 57521

7.000 0.500 CRWH1 V 57523
7.000 0.500 CRWHA1 R 57531
5.875 7.125 0.500 CRWH1 R 58716

7.125 0.500 CRWH1 V 58717
7.125 0.500 CRWHA1 R 58741
7.500 0.500 CRWH1 R 58760
6.000 6.750 0.500 CRWA1 V 59999

6.750 0.500 CRW1 V 60000
7.500 0.500 CRWA1 R 60016

7.500 0.500 CRWHA1 V 60026
7.500 0.500 CRWHA1 R 60028
6.125 7.125 0.625 CRWH1 R 612101)

7.625 0.625 CRWH1 R 612551)
7.625 0.625 CRWH1 P 612561)
6.250 7.252 0.500 CRWH1 R 624821)

7.500 0.500 CRWH1 R 624951)
7.500 0.500 CRWH1 V 62497
7.750 0.500 CRWH1 R 62535

7.875 0.625 CRWH1 R 62572
6.375 7.375 0.625 CRWH1 R 63700
7.875 0.563 CRWHA1 R 63734

7.875 0.625 CRWH1 R 637331)
6.500 7.500 0.500 CRWA1 R 64993

7.500 0.500 CRWH1 R 649941)
7.500 0.500 CRWH1 V 64998
8.000 0.500 CRW1 R 65021

8.000 0.500 CRWHA1 R 650371)
6.625 8.125 0.500 CRWH1 R 662411)
6.750 8.000 0.500 CRWH1 R 67515

8.250 0.500 CRWH1 R 675331)
6.875 8.375 0.500 CRWH1 R 687451)
7.000 8.000 0.630 CRWH1 R 70016

8.250 0.625 CRWH1 R 700281)
8.500 0.500 CRWA1 R 70080

8.500 0.625 CRWH1 R 70052
8.500 0.625 CRWHA1 R 70053
8.500 0.625 CRWHA1 V 70054
d1 7.125 – 12.250 in.
d1 D

seal width
d1 D b
in. – –
7.125 8.625 0.625 CRWH1 R 712451)
7.250 8.250 0.625 CRW1 R 725151)

8.750 0.625 CRWHA1 R 72539
8.750 0.750 CRWH1 P 725421)
9.055 0.625 CRWHA1 R 72570
7.375 8.875 0.625 CRWH1 R 737451)
7.500 8.500 0.625 CRWH1 R 750301)

9.000 0.625 CRWH1 R 75050
9.000 0.625 CRWHA1 P 75052
7.625 8.625 0.563 CRWH1 R 762151)

9.125 0.625 CRWH1 R 762551)
7.750 9.250 0.625 CRWH1 R 775401)
7.875 9.250 1.000 CRWHA1 R 787251)

9.375 0.625 CRWH1 R 787381)
8.000 9.000 0.625 CRWH1 R 799601)

9.000 0.625 CRWHA1 R 799611)
9.250 0.625 CRWH1 R 799971)

9.250 0.625 CRWHA1 R 79998
9.500 0.625 CRWH1 R 80010
10.000 0.625 CRWHA1 R 800381)
8.125 10.125 0.625 CRWH1 R 812451)

10.125 0.625 CRWHA1 R 812461)
8.250 9.250 0.625 CRWH1 R 825101)

9.252 0.500 CRWH1 R 82527
9.500 0.578 CRW1 R 5414051)
10.250 0.625 CRWH1 R 825601)

seal width
d1 D b
in. – –
8.500 9.750 0.625 CRWH1 R 85002

10.000 0.625 CRWH1 R 850091)
10.500 0.625 CRWH1 R 850151)

2.2
10.625 0.625 CRWHA1 R 850851)
8.625 10.625 0.625 CRWH1 R 862601)
8.750 10.750 0.625 CRWH1 R 875411)
8.875 10.125 0.625 CRWH1 R 887101)

10.875 0.625 CRWH1 R 887601)
9.000 10.000 0.625 CRWH1 R 900061)

11.000 0.625 CRWH1 R 900361)
9.250 11.250 0.625 CRWHA1 R 92536

12.750 0.625 CRWHA1 R 925701)
12.750 1.250 CRWHA1 R 925741)
9.500 10.500 0.438 CRW1 R 95048

11.500 0.625 CRW1 R 95062
9.625 11.625 0.625 CRWH1 R 962451)

11.125 0.625 CRWH1 R 975421)
11.250 0.625 CRWH1 R 975451)
11.750 0.625 CRWH1 R 975501)
10.000 11.252 0.625 CRWHA1 R 1000441)

12.000 0.625 CRWH1 R 1000511)
12.000 0.625 CRWA1 R 100075
10.250 11.250 0.563 CRWH1 R 1025201)

12.250 0.625 CRWH1 R 1025401)
10.500 11.750 0.625 CRWH1 R 1050101)

12.500 0.625 CRWH1 R 1050511)
10.750 12.750 0.625 CRWH1 R 1075511)
11.000 12.250 0.625 CRWHA1 R 1100301)

13.000 0.625 CRWH1 R 1100511)
11.375 13.000 0.625 CRW1 R 1137401)
11.500 13.000 0.625 CRWH1 R 1150211)

13.500 0.625 CRWH1 R 1150411)
12.000 14.000 0.625 CRW1 R 1200601)
12.250 13.375 0.625 CRWH1 R 1225551)

13.813 0.625 CRW1 R 1225801)
14.250 1.000 CRWHA1 R 1225901)
Radial shaft seals
CRW5 and CRWA5 seals

CRW5 and CRWA5 seals are designed to with-
stand moderate pressure differentials. They
have an SKF Wave lip to reduce heat generation CRW5
and a metal outside diameter for easy installa-
tion and a firm and accurate fit in the housing
bore. See pages 57 and 58 for more information
on SKF Wave lip design. Most of them have SKF
Bore Tite Coating on the outside diameter. The
CRWA5 seals have an auxiliary lip, providing CRWA5
additional contaminant exclusion ability. A
shoulder or retaining ring should be used at the
low-pressure side of the seal to prevent it from
being pressed out of the housing bore.
CRW5: Seal with one steel case, SKF Wave lip

and a carbon steel garter spring.
CRWA5: Seal with one steel case, SKF Wave lip,

a carbon steel garter spring and an auxiliary,
contacting lip.
The CRW5 and CRWA5 seals are available in

inch sizes with sealing lips made of either nitrile
rubber or the SKF fluoro rubber compound SKF
Duralife. Other materials are also available on
request.
Radial shaft seals – CRW5 and CRWA5 – inch dimensions

d1 0.313 – 0.875 in.
d1 D
2.3

seal width
d1 D b
in. – –
0.313 0.686 0.313 CRWA5 R 30941)

0.749 0.250 CRWA5 R 31011)
0.749 0.250 CRWA5 V 31031)
0.999 0.313 CRWA5 R 31711)
0.375 0.749 0.250 CRW5 R 36891)

1.124 0.375 CRW5 V 3807
0.500 0.875 0.313 CRWA5 R 4940

0.875 0.313 CRWA5 V 4941
0.999 0.250 CRWA5 V 4991

0.999 0.313 CRWA5 R 4996
1.124 0.250 CRWA5 R 5069

1.124 0.250 CRWA5 V 5072
0.625 0.999 0.250 CRWA5 R 6151

1.124 0.250 CRW5 R 6191
1.124 0.374 CRWA5 V 6231
1.124 0.375 CRWA5 R 6229
1.126 0.250 CRW5 R 6242
1.250 0.313 CRWA5 R 62801)

1.250 0.313 CRWA5 V 62851)
1.375 0.250 CRW5 P 6371

1.375 0.375 CRWA5 R 6388
1.500 0.313 CRW5 V 6393
0.750 1.250 0.250 CRWA5 R 7434

1.250 0.375 CRWA5 R 7449
1.375 0.250 CRWA5 V 7509
0.875 1.250 0.250 CRWA5 V 8634

1.375 0.250 CRWA5 R 8660
1.375 0.250 CRWA5 V 8665
1.497 0.313 CRWA5 V 8694
Radial shaft seals – CRW5 and CRWA5 – inch dimensions

d1 0.984 – 2.500 in.
d1 D

seal width
d1 D b
in. – –
0.984 1.596 0.250 CRWA5 R 9700

1.752 0.313 CRWA5 V 9805
1.000 1.375 0.250 CRWA5 R 9814

1.499 0.250 CRWA5 R 9843
1.499 0.250 CRW5 R 98551)
1.499 0.250 CRWA5 V 9858
1.500 0.250 CRWA5 R 9863

1.752 0.313 CRWA5 R 9967
2.000 0.313 CRWA5 R 10131
1.125 1.626 0.250 CRWA5 V 11139
1.250 1.687 0.313 CRWA5 R 12333

1.750 0.250 CRWA5 V 12339
1.750 0.250 CRWA5 R 12360
1.997 0.438 CRWA5 V 12438

2.328 0.500 CRWA5 R 12609
2.502 0.500 CRWA5 R 12640
1.500 1.997 0.250 CRWA5 V 14844

2.064 0.375 CRWA5 V 14868
2.311 0.500 CRWA5 V 14979
2.328 0.500 CRWA5 R 14977
1.750 2.502 0.500 CRWA5 R 17374
1.938 2.675 0.250 CRWA5 R 19213

2.835 0.250 CRWA5 R 19278
2.500 3.251 0.350 CRWA5 R 24892
2.3
Radial shaft seals
HDW1 seals
HDW1 seals are heavy-duty SKF Wave lip seals,
designed for use in grease or oil lubricated appli
cations. The seals are produced standard with HDW1
a heavy-duty seal body, SKF Bore Tite Coating
on the metal outside diameter, SKF Wave lip in
nitrile rubber, and a carbon steel garter spring.
The rigid seal body can withstand operating
pressures up to 0,24 MPa (35 psi), dynamic, and
0,34 MPa (50 psi), static, while withstanding
shaft speeds up to 25 m/s (4 900 ft/min) at shaft
diameters < 203 mm (8 in.).
The HDW1 seals are available in inch sizes.
Radial shaft seals – HDW1 – inch dimensions

d1 5.000 – 7.938 in.
d1 D
2.4
Dimensions Design and Designation Dimensions Design and Designation

Shaft Bore Nominal lip material Shaft Bore Nominal lip material
d1 D b d1 D b
in. – – in. – –
5.000 6.125 0.500 HDW1 R 49951 6.625 7.625 0.500 HDW1 R 66217
7.125 0.500 HDW1 R 50186 7.750 0.500 HDW1 R 66219
7.875 0.500 HDW1 R 66222
5.063 6.125 0.500 HDW1 R 50620 8.000 0.500 HDW1 R 66230
5.125 6.625 0.500 HDW1 R 51277 6.750 7.750 0.500 HDW1 R 67510
7.000 0.500 HDW1 R 51330 8.750 0.500 HDW1 R 67600
5.188 6.250 0.500 HDW1 R 51800 6.875 8.250 0.500 HDW1 R 68730
8.500 0.500 HDW1 R 68760
5.250 6.750 0.500 HDW1 R 52651
7.125 0.500 HDW1 R 52655 7.125 8.250 0.500 HDW1 R 71220
5.313 6.375 0.500 HDW1 R 53100 7.375 8.375 0.500 HDW1 R 73720
8.500 0.500 HDW1 R 73730
5.438 6.625 0.500 HDW1 R 54300
7.500 8.750 0.500 HDW1 R 75046
5.875 6.875 0.500 HDW1 R 587091) 9.250 0.500 HDW1 R 75069
7.000 0.500 HDW1 R 58710
7.625 8.875 0.500 HDW1 R 76225
5.938 7.000 0.500 HDW1 R 59300
7.750 8.750 0.500 HDW1 R 77506
6,000 7.250 0.500 HDW1 R 60009
7.875 8.875 0.500 HDW1 R 78710
6.063 7.500 0.500 HDW1 R 60650
7.938 9.125 0.500 HDW1 R 79620
6.125 7.125 0.500 HDW1 R 61215
7.250 0.500 HDW1 R 61230
7.375 0.500 HDW1 R 61235
6.250 7.250 0.500 HDW1 R 62480
6.375 7.500 0.500 HDW1 R 63717
6.438 7.500 0.500 HDW1 R 64330
1) Stainless steel garter spring
Radial shaft seals
CRS1, CRSH1, CRSA1 and CRSHA1 seals

All CRS seals are designed with a metal case and
a conventional spring-loaded sealing lip. Some
of them have a sealant on the outside diameter CRS1
to compensate for imperfections in the housing
bore.
CRS1: Seal with a single steel case, a conven-

tional sealing lip and a carbon steel garter
spring. CRSH1
CRSA1: Seal with a single steel case, a conven-

tional sealing lip, a carbon steel garter spring
and an auxiliary, contacting lip.
CRSH1: Seal with a double steel case, a conven- CRSA1

tional sealing lip and a carbon steel garter
spring.
CRSHA1: Seal with a double steel case, a con-

ventional sealing lip, a carbon steel garter
spring and an auxiliary, contacting lip. CRSHA1
CRS seals are available with sealing lips made

of nitrile rubber for general-purpose applications
and of fluoro rubber, providing improved high
temperature and chemical resistance.
Radial shaft seals – CRS1, CRSH1, CRSA1 and CRSHA1 – metric dimensions
d1 12 – 37 mm
d1 D
2.5

seal width
d1 D b
mm. – –
12 20 5 CRSA1 R 12¥20¥5 CRSA1 R
13 28 7 CRS1 R 13¥28¥7 CRS1 R
19 37 10 CRS1 V 19¥37¥10 CRS1 V
20 30 5 CRS1 R 20¥30¥5 CRS1 R

30 7 CRS1 V 20¥30¥7 CRS1 V
32 7 CRS1 V 20¥32¥7 CRS1 V
42 7 CRS1 V 20¥42¥7 CRS1 V
22 32 7 CRS1 V 22¥32¥7 CRS1 V
24 38 10 CRS1 R 24¥38¥10 CRS1 R
25 32 7 CRSA1 R 25¥32¥7 CRSA1 R

47 10 CRSA1 V 25¥47¥10 CRSA1 V
52 7 CRS1 R 25¥52¥7 CRS1 R
26 35 7 CRS1 R 26¥35¥7 CRS1 R

42 8 CRS1 R 26¥42¥8 CRS1 R
27 37 7 CRS1 V 27¥37¥7 CRS1 V

41 10 CRSH1 R 27¥41¥10 CRSH1 R
28 62 12 CRSH1 R 28¥62¥12 CRSH1 R
30 45 8 CRS1 V 30¥45¥8 CRS1 V

52 9 CRSH1 R 30¥52¥9 CRSH1 R
32 46 8 CRS1 R 32¥46¥8 CRS1 R
34 52 10 CRS1 R 34¥52¥10 CRS1 R

54 11 CRS1 R 34¥54¥11 CRS1 R
35 64 8 CRSA1 P 35¥64¥8 CRSA1 P

65 12 CRSA1 R 35¥65¥12 CRSA1 R
36 46 9 CRS1 R 36¥46¥9 CRS1 R

56 10 CRS1 R 36¥56¥10 CRS1 R
37 55 10 CRSH1 R 37¥55¥10 CRSH1 R
Radial shaft seals – CRS1, CRSH1, CRSA1 and CRSHA1 – metric dimensions
d1 40 – 260 mm
d1 D

seal width
d1 D b
mm – –
40 55 10 CRS1 R 40¥55¥10 CRS1 R

60 10 CRSA1 R 40¥60¥10 CRSA1 R
42 62 10 CRS1 R 42¥62¥10 CRS1 R
43 62 10 CRSH1 R 43¥62¥10 CRSH1 R
45 58 9 CRSA1 R 45¥58¥9 CRSA1 R

62 7 CRSA1 R 45¥62¥7 CRSA1 R
48 70 9 CRSA1 R 48¥70¥9 CRSA1 R
50 62 7 CRS1 R 50¥62¥7 CRS1 R

62 10 CRS1 R 50¥62¥10 CRS1 R
85 13 CRSH1 R 50¥85¥13 CRSH1 R
54 72 10 CRSA1 R 54¥72¥10 CRSA1 R

80 10 CRSH1 R 54¥80¥10 CRSH1 R
57 72 10 CRSH1 R 57¥72¥10 CRSH1 R
58 85 13 CRSH1 R 58¥85¥13 CRSH1 R
59 75 10 CRSA1 R 59¥75¥10 CRSA1 R
60 70 7 CRS1 R 60¥70¥7 CRS1 R

78 9 CRS1 R 60¥78¥9 CRS1 R1)
80 10 CRSHA1 R 60¥80¥10 CRSHA1 R
90 10 CRSH1 R 60¥90¥10 CRSH1 R
62 75 10 CRS1 R 62¥75¥10 CRS1 R
66 80 8,9 CRSHA1 R 66¥80¥9 CRSHA1 R

85 10 CRSHA1 R 66¥85¥10 CRSHA1 R
90 13 CRSH1 R 66¥90¥13 CRSH1 R
68 85 10 CRS1 R 68¥85¥10 CRS1 R
74 100 13 CRSH1 R 74¥100¥13 CRSH1 R
1) Sealant on outside diameter

seal width
d1 D b
mm – –
75 115 13 CRSH1 R 75¥115¥13 CRSH1 R
80

100
125
13
13
CRSA1 R
CRSH1 R
80¥100¥13 CRSA1 R
80¥125¥13 CRSH1 R
2.5
85 100 9 CRS1 R 85¥100¥9 CRS1 R
88 110 13 CRSH1 R 88¥110¥13 CRSH1 R
90 125 13 CRSH1 R 90¥125¥13 CRSH1 R
95 110 9 CRS1 R 95¥110¥9 CRS1 R
100 120 13 CRSH1 R 100¥120¥13 CRSH1 R
105 125 12 CRS1 R 105¥125¥12 CRS1 R
107 123 11 CRSA1 R 107¥123¥11 CRSA1 R
108 130 13 CRSH1 R 108¥130¥13 CRSH1 R
113 140 13 CRSH1 R 113¥140¥13 CRSH1 R
115 160 15 CRSH1 R 115¥160¥15 CRSH1 R
120 150 15 CRSH1 R 120¥150¥15 CRSH1 R
125 146 14 CRSA1 P 125¥146¥14 CRSA1 P
126 147 11 CRSA1 R 126¥147¥11 CRSA1 R
130 150 10 CRSA1 R 130¥150¥10 CRSA1 R

150 14 CRSA1 R 130¥150¥14 CRSA1 R
155 10 CRSH1 R 130¥155¥10 CRSH1 R
160 13 CRS1 R 130¥160¥13 CRS1 R
160 13 CRSA1 R 130¥160¥13 CRSA1 R
165 13 CRSH1 R 130¥165¥13 CRSH1 R
135 160 13 CRSH1 R 135¥160¥13 CRSH1 R

170 15 CRSH1 R 135¥170¥15 CRSH1 R
138 152 12 CRSA1 R 138¥152¥12 CRSA1 R
145 164 14 CRSA1 R 145¥164¥14 CRSA1 R

175 14 CRS1 R 145¥175¥14 CRS1 R
150 170 15 CRSH1 R 150¥170¥15 CRSH1 R

180 13 CRSH1 R 150¥180¥13 CRSH1 R
200 15 CRSH1 R 150¥200¥15 CRSH1 R
154 175 13 CRSA1 R 154¥175¥13 CRSA1 R
160 185 13 CRSA1 V 160¥185¥13 CRSA1 V
168 200 15 CRSH1 R 168¥200¥15 CRSH1 R
170 190 15 CRSH1 R 170¥190¥15 CRSH1 R
180 200 12 CRS1 R 180¥200¥12 CRS1 R

215 16 CRS1 R 180¥215¥16 CRS1 R
220 16 CRSA1 R 180¥220¥16 CRSA1 R
190 215 16 CRSH1 R 190¥215¥16 CRSH1 R
195 230 15 CRSH1 R 195¥230¥15 CRSH1 R
200 250 15 CRSH1 R 200¥250¥15 CRSH1 R
260 300 20 CRS1 R 260¥300¥20 CRS1 R
Radial shaft seals – CRS1, CRSH1, CRSA1 and CRSHA1 – inch dimensions
d1 0.531 – 2.008 in.
d1 D

seal width
d1 D b
in. – –
0.531 1.124 0.313 CRSA1 R 5334
0.594 1.250 0.313 CRSA1 R 5950

1.375 0.313 CRSA1 R 59661)
0.669 1.339 0.311 CRSA1 P 6992
0.709 1.339 0.315 CRSA1 P 7089
0.781 1.752 0.313 CRSHA1 R 8213
0.844 1.828 0.313 CRSA1 R 8485
0.945 1.575 0.315 CRS1 R 9515
0.969 2.048 0.375 CRS1 R 96881)
1.125 2.835 0.375 CRSA1 R 114051)

2.875 0.469 CRSH1 R 114101)
1.156 2.125 0.438 CRSH1 R 115661)
1.219 2.000 0.438 CRSH1 R 121311)
1.250 2.561 0.500 CRSH1 R 12655

2.713 0.469 CRSH1 R 126601)
3.156 0.500 CRSH1 R 12678
1.301 2.000 0.438 CRSA1 P 12905
1.313 1.874 0.375 CRSA1 R 130271)

2.000 0.313 CRSA1 R 130371)
2.106 0.375 CRSA1 R 130841)
2.996 0.500 CRSH1 R 132751)
1.328 2.312 0.433 CRS1 R 134191)
1.362 2.191 0.250 CRS1 P 13500

seal width
d1 D b
in. – –
1.375 2.750 0.500 CRSH1 R 139061)

3.000 0.500 CRSHA1 R 13937

3.125
3.350
0.500
0.469
CRSH1 R
CRSH1 R
13936
139341)
2.5
1.399 2.292 0.469 CRSA1 R 139921)
2.292 0.500 CRSA1 R 139901)
1.414 2.250 0.250 CRSHA1 R 140351)
1.469 2.374 0.375 CRSA1 R 146411)
1.491 2.191 0.250 CRSA1 R 14780
1.500 2.996 0.500 CRSH1 R 15240

3.000 0.375 CRSA1 R 15241
1.524 2.374 0.500 CRSH1 R 15343
1.563 2.716 0.469 CRSH1 R 157481)
1.618 2.575 0.500 CRSA1 R 164041)
1.625 2.437 0.469 CRSHA1 R 16121

2.835 0.469 CRSH1 R 16386
3.062 0.500 CRSH1 R 164311)
3.251 0.500 CRSH1 R 164401)
1.656 2.502 0.500 CRSH1 R 165321)
1.688 2.374 0.313 CRSA1 R 16669

2.835 0.469 CRSA1 R 16960
1.705 3.084 0.500 CRS1 R 17053
1.719 2.623 0.500 CRSH1 R 171361)
1.750 2.328 0.438 CRS1 R 17257

3.154 0.313 CRS1 R 17726
3.937 0.313 CRSA1 R 177711)
1.781 2.750 0.500 CRSH1 R 17847

2.758 0.500 CRSH1 R 178511)
1.844 2.502 0.375 CRSA1 R 184121)

2.750 0.375 CRSA1 R 184461)
1.875 3.125 0.313 CRSA1 R 188791)
1.889 3.110 0.688 CRSA1 P 18983
1.890 2.874 0.276 CRSA1 P 18979
1.906 3.189 0.313 CRSA1 P 19062
1.938 2.762 0.500 CRSA1 R 192731)

2.825 0.500 CRSH1 P 19274
3.751 0.500 CRSH1 R 194661)
1.969 2.638 0.354 CRSA1 R 19628

2.686 0.500 CRSH1 R 19615
2.742 0.500 CRSH1 P 19620
2.875 0.469 CRSH1 R 19643
2.008 2.953 0.354 CRSA1 P 20012
Radial shaft seals – CRS1, CRSH1, CRSA1 and CRSHA1 – inch dimensions
d1 2.063 – 7.000 in.
d1 D

seal width
d1 D b
in. – –
2.063 2.875 0.375 CRSA1 R 5500851)
2.125 3.623 0.469 CRSA1 P 21379
2.145 3.188 0.469 CRSH1 R 21538
2.188 3.623 0.500 CRSHA1 R 21950
2.432 3.070 0.227 CRSA1 P 24110
2.563 3.500 0.500 CRSHA1 P 25587
2.648 3.812 0.500 CRS1 R 26877
2.750 4.125 0.438 CRS1 P 275761)

4.125 0.563 CRSA1 R 27577
2.875 3.434 0.294 CRSA1 R 286461)
2.913 3.543 0.394 CRS1 P 29105
3.125 3.936 0.512 CRSA1 V 311441)
3.250 3.876 0.375 CRSA1 V 323321)

4.125 0.563 CRSH1 R 323621)
3.298 4.125 0.563 CRSA1 R 328151)
3.469 4.626 0.625 CRSA1 R 34700
3.500 5.751 0.563 CRSH1 R 351111)
3.504 4.173 0.354 CRSA1 V 35120
3.813 4.999 0.469 CRSH1 R 38160

5.251 0.469 CRSH1 R 382201)
3.875 5.501 0.500 CRSHA1 R 387491)

5.751 0.563 CRSH1 R 38810

seal width
d1 D b
in. – –
3.898 4.680 0.370 CRSA1 VR 38770
4.188

4.999
5.251
0.469
0.469
CRSHA1 R
CRSH1 R
41751
41761
2.5
5.751 0.500 CRSHA1 R 41833
4.313 5.751 0.500 CRSH1 R 43231
4.563 5.751 0.500 CRSHA1 R 45550

6.250 0.500 CRSH1 R 45560
5.000 7.000 0.500 CRSHA1 R 50185

7.500 0.500 CRSHA1 R 50195
5.125 6.500 0.500 CRSHA1 R 51276
5.313 6.500 0.500 CRSHA1 R 53151
5.375 6.374 0.500 CRSHA1 R 536881)

6.499 0.563 CRSH1 R 53692
5.500 6.626 0.563 CRSHA1 R 54949

6.876 0.563 CRSHA1 R 55157
7.501 0.563 CRSH1 R 55179
5.750 6.876 0.563 CRSHA1 R 57519

7.126 0.563 CRSHA1 R 57578
7.502 0.563 CRSHA1 R 57584
6.000 7.002 0.500 CRSHA1 R 600061)
6.062 6.772 0.551 CRSA1 R 60620
6.125 7.502 0.563 CRSHA1 R 612481)
6.188 7.500 0.563 CRSH1 P 61740
7.000 8.375 0.625 CRSHA1 R 70034
Radial shaft seals
PTFE radial shaft seals PTFE seals without a metal case can be de-
Radial shaft seals with one or more PTFE sealing signed with an O-ring in the outside diameter
lip(s) are designed to withstand aggressive groove to provide static sealing ability. Both the
environments, high temperatures, high pres- PTFE and O-ring material can be selected to
sures and dry running that traditional radial meet the demands of different operating condi-
shaft seals made of elastomeric sealing lip ma- tions, e.g. in the food industry to enable disas-
terials cannot withstand. Many of the PTFE sembly of the equipment for cleaning.
compounds are FDA approved. Main advantages
of PTFE seals include:
• High chemical resistance

• Withstand speeds up to 30 m/s (5 900 ft/min)
• Wide operating temperature range, –70 to
+250 °C (–95 to +480 °F)
• Withstand pressures up to 3,5 MPa (500 psi)
• Withstand dry running
Assortment
The profiles shown below are a selection of the
most commonly used SKF seal designs with
sealing lips made of PTFE. They can be installed
in existing housing grooves where traditional
radial seals are used, provided that the grooves
are manufactured in accordance with inter
national standards.
There are two main executions of PTFE seals:
those with a metal case and those without a
metal case. The metal case can be made of
steel, aluminium or any of the stainless steel
materials SS 304, SS 316 and SS 316 TI. The
PTFE material should be selected based on the
needs of the application.
SL SLA
SLX SLS YSLE
DL DLA YNSLE YSL
PTFE materials
The selection of seal materials typically requires
a compromise between advantages and disad-
vantages. There are hundreds of different PTFE
materials with a variety of fillers. Common fillers
include glass fibre, carbon, graphite, molybdenum
disulphide, metal oxides and various polymers.
Each possesses different properties, appropriate
for different applications and service conditions. 2
Common to all filled PTFE materials are their
improved resistance to wear and deformation.
Unfilled PTFE provides, in most cases, a lower
coefficient of friction than a filled PTFE material
and the lowest degree of wear of the seal coun-
terface. However, a sealing lip made of an unfilled
PTFE material has limited resistance to wear
and deformation under load.
The PTFE materials that SKF most often rec-
ommends are listed in table 14 on page 176.
In addition to PTFE-based compounds, SKF also
offers radial shaft seals in other modified plas-
tics, some of which are listed in table 15 on
page 177.
Selecting the appropriate material for the
metal case and the O-ring(s) is also of significant
importance to achieving satisfactory sealing
performance. Contact SKF for more information.
Installation
Special care must be taken during handling and
installation of PTFE seals. For more information,
refer to pages 85 and 86.
Size range and availability

The majority of PTFE radial shaft seals from SKF
are made to order to meet the demands of each
application. There are, however, certain standard
sizes within the ranges of approximately 6 to
200 mm (0.250 to 8 in.) shaft diameter and ap-
proximately 16 to 230 mm (0.630 to 9 in.) bore
diameter. Contact SKF for more information re-
garding designs and sizes.
Radial shaft seals
Table 14
Material family Description Shaft hardness recommended1)
PTFE, unfilled “Virgin” PTFE. FDA approved. Low-friction material. Used for A
general non-pressure applications on shafts with low hardness
value. Excellent for cryogenics.
PTFE + glass FDA approved. Glass can be in the form of beads or fibres. Glass is C
exceptionally strong and prolongs the life of the base PTFE. Due to
its inherent hardness, it also adds an abrasive property and is not
recommended on low-hardness shafts.
PTFE + MoS2 Molybdenum disulphide (MoS2) adds wear resistance to the base C
PTFE. Not as abrasive as glass.
PTFE + glass + MoS2 Improved elongation characteristics and less abrasive to running C
surfaces compared to PTFE + glass.
PTFE + carbon Carbon can be in the form of various grades of fibres or graphite A, B, C
powder, either natural or synthetic. Carbon is an excellent natural
lubricant and provides wear resistance to enhance the low-friction
base PTFE material. Increased percentage of carbon will increase
the wear, creep, and extrusion resistance and improve performance
in steam and chemical service at elevated temperatures and
pressures.
PTFE + carbon + MoS2 Excellent wear rate in non-lubricated services at high B, C

temperatures.
PTFE + bronze Suitable for high-speed dynamic sealing of hydraulic media. Should
not be used in chemical service, which could attack the bronze.
PTFE + bronze + MoS2 High degree of wear and extrusion resistance in high-pressure
applications.
PTFE + polymer Polymers, such as polyoxybenzoate, polyimide and many others A, B, C

improve creep and wear resistance.
PTFE + organic pigment FDA and/or USDA 3A approved.
1) Material
selection recommendations for counterface hardness ratings (Rockwell C scale) combined with surface speed.
For material selection, please see table 16
Table 15
Modified plastic materials
UHMWPE Ultra-high molecular weight polyethylene.

Significantly improved wear and abrasion
resistance over PTFE-based materials in non-
lubricated or abrasive media. FDA and USDA 3A
approved. Fair media compatibility, limited to
approximately 90 °C (195 °F).
2
Nylon Improved strength, limited media compatibility
and temperature resistance. Hydroscopic. Used
for plain bearings, bushings, back-up rings and
some seals.
POM Polyoxymethylene (a.k.a. polyacetal or just

acetal). Similar to nylon but with significantly
reduced water-absorption properties. Some
grades are FDA and USDA 3A compliant.
Typically used for plain bearings, bushings,
and back-up rings.
Ertalyte Similar to POM but offers improved media

compatibility and improved wear resistance.
PEEK Polyetheretherketone. Similar strength

properties as nylon and POM but with very
good media compatibility and significantly
better temperature properties. Some grades
are FDA and USDA 3A compliant. Used for plain
bearings, bushings, back-up rings and some
seals.
PPS Polyphenylene sulphide. Similar strength

properties and chemical compatibility as PEEK-
based compounds but offers improved wear
resistance. Has better temperature capabilities
than nylon or POM materials but not as good as
PEEK. Adding fillers can create a “bearing-
grade” PPS for high-performance applications.
PA Polyamide. Exceptional mechanical, thermal

and chemical resistance properties.
Table 16
Material selection with shaft hardness + velocity
Surface speed < 30 HRC 45 HRC ≥ 58 HRC
Low A or B A, B, C A, B, C
Medium A A, B A, B, C
High A A, B A, B
Radial shaft seals
HM and TL seals for grease lubricated

applications
SKF offers an extensive assortment of radial
shaft seals for less demanding grease lubricated
applications operating at moderate speeds. The
majority of these seals are designed without a
spring. The seals are generally installed with the
sealing lip facing outward to provide maximum
exclusion ability. Typical applications are grease
lubricated agriculture machinery. The illus
trations below show the most commonly used
designs within this assortment from SKF. Contact
SKF for more information on available designs.
permissible operating conditions, valid for both
HM and TL seals.
HM1 HM3 HM4 HM8 HM11 HM12
HM14 HM18 HM21 HM102 HMA6 HMA8
HMA10 HMA11 HMA14 HMA21 HMA22 HMA76
HMA85 HMA94 HMA96
TL1 TL4 TL5 TL6 TL7 TL8
Radial shaft seals – HM and TL seals – metric dimensions

d1 6 – 22 mm
d1 D
2.6

seal width
d1 D b
mm – –
6 12 2 HM3 R 6¥12¥2 HM3 R

8 12 3 HM4 R 8¥12¥3 HM4 R

9 13 3 HM4 R 9¥13¥3 HM4 R

10 14 3 HM4 R 10¥14¥3 HM4 R
16 4 HM102 R 10¥16¥4 HM102 R

12 16 3 HM4 R 12¥16¥3 HM4 R
18 3 HM4 R 12¥18¥3 HM4 R
19 3 HM4 R 12¥19¥3 HM4 R
22 4 HM4 R 12¥22¥4 HM4 R

14 20 3 HM4 R 14¥20¥3 HM4 R
22 3 HM4 R 14¥22¥3 HM4 R

15 21 3 HM4 R 15¥21¥3 HM4 R
23 3 HM4 R 15¥23¥3 HM4 R
25 5 HMA10 R 15¥25¥5 HMA10 R

16 22 3 HM4 R 16¥22¥3 HM4 R
22 4 HM4 R 16¥22¥4 HM4 R
24 4 HM102 R 16¥24¥4 HM102 R

17 23 3 HM4 R 17¥23¥3 HM4 R

18 24 3 HM4 R 18¥24¥3 HM4 R
26 4 HMA1 R 18¥26¥4 HMA1 R

19 27 4 HM4 R 19¥27¥4 HM4 R

20 26 4 HM4 R 20¥26¥4 HM4 R
28 4 HM4 R 20¥28¥4 HM4 R

22 28 4 HM1 R 22¥28¥4 HM1 R
28 4 HMA10 R 22¥28¥4 HM10 R
30 4 HM4 R 22¥30¥4 HM4 R
35 5 HM14 R 22¥35¥5 HM14 R

Radial shaft seals – HM and TL seals – metric dimensions

d1 23 – 65 mm
d1 D

seal width
d1 D b
mm – –
23 32 5,50 HM1 R 23¥32¥6 HM1 R

35 6 HMA10 R 23¥35¥6 HMA10 R

24 32 4 HM4 R 24¥32¥4 HM4 R

25 32 4 HM4 R 25¥32¥4 HM4 R
33 4 HM4 R 25¥33¥4 HM4 R
35 4 HM4 R 25¥35¥4 HM4 R

26 34 4 HM4 R 26¥34¥4 HM4 R

28 35 4 HM4 R 28¥35¥4 HM4 R
35 6 HM102 R 28¥35¥6 HM102 R
37 4 HM4 R 28¥37¥4 HM4 R

30 37 4 HM4 R 30¥37¥4 HM4 R
40 4 HM4 R 30¥40¥4 HM4 R

32 42 4 HM4 R 32¥42¥4 HM4 R

35 42 4 HM4 R 35¥42¥4 HM4 R
45 4 HM4 R 35¥45¥4 HM4 R
47 5 HM4 R 35¥47¥5 HM4 R

37 47 4 HM4 R 37¥47¥4 HM4 R

38 48 4 HM4 R 38¥48¥4 HM4 R

40 47 4 HM4 R 40¥47¥4 HM4 R
50 4 HM4 R 40¥50¥4 HM4 R
52 5 HM4 R 40¥52¥5 HM4 R
53 5 HMA76 R 40¥53¥5 HMA76 R
62 10 HMA10 R 40¥62¥10 HMA10 R

42 52 4 HM4 R 42¥52¥4 HM4 R
55 6 HM1 R 42¥55¥6 HM1 R
64 6 HMA1 R 42¥64¥6 HMA1 R


seal width
d1 D b
mm – –
45 52 4 HM4 R 45¥52¥4 HM4 R

55 4 HM4 R 45¥55¥4 HM4 R
72

8 HMA22 R 45¥72¥8 HMA22 R 2.6
47 72 6 HMA85 R 47¥72¥6 HMA85 R

48 58 4 HM4 R 48¥58¥4 HM4 R

50 60 6 HMA10 R 50¥60¥6 HMA10 R
62 5 HM4 R 50¥62¥5 HM4 R

62 78 7 HMA8 R 62¥78¥7 HMA8 R

65 75 8 HM102 R 65¥75¥8 HM102 R
Radial shaft seals – HM and TL seals – inch dimensions

d1 0.188 – 0.750 in.
d1 D

Shaft Bore Nominal Clearance lip material
seal width
d1 D b B3
in. – –
0.188 0.500 0.125 HM1 R 1850

0.250 0.499 0.188 HM14 R 2450
0.499 0.188 HMA14 V 2452
0.562 0.188 HM14 R 24701)
0.626 0.250 HM14 R 2490
0.749 0.188 HM14 R 2560

0.313 0.500 0.125 HM4 R 3044
0.626 0.156 HM14 R 30601)
0.626 0.156 HM14 V 3061
0.626 0.203 HM1 R 30501)
0.633 0.141 HM14 R 3080
0.749 0.250 HM14 R 3140

0.750 0.250 HM3 R 3141
0.862 0.250 HM14 R 3086

0.375 0.562 0.093 HM3 V 535835
0.563 0.094 HM3 R 3621
0.628 0.197 HMA10 P 3632

0.687 0.156 HM14 R 36451)
0.749 0.250 HM14 R 3683

0.875 0.250 HM14 R 3727

0.404 0.620 0.188 HM14 R 4010
0.862 0.250 HM14 R 4012

0.438 0.836 0.188 HM14 R 4231
0.879 0.180 HM8 R 4256
0.999 0.250 HM14 R 4340

0.469 0.836 0.188 HM14 P 4623
0.875 0.219 HM14 R 4628

0.500 0.687 0.093 HM3 V 538545
0.688 0.094 HM3 R 4911
0.750 0.125 HM14 R 49121)
1) SKF Bore Tite Coating

seal width
d1 D b B3
in. – –
0.500 0.820 0.156 HM14 R 49141)

cont. 0.843 0.250 HM14 R 49231)

0.875 0.125
0.875 0.250
HM14 R
HM14 R
4925
4938
2.6
0.999 0.188 HM14 R 49501)
0.999 0.250 HM14 R 49901)
1.124 0.250 HM14 R 50851)

0.551 1.124 0.203 HM21 R 53991)

0.563 0.750 0.094 HM3 R 5500
0.875 0.188 HM14 R 55221)
0.999 0.219 HM14 R 55691)
1.124 0.250 HM14 R 5685

0.594 1.124 0.250 HM14 R 59461)

0.624 1.131 0.188 HM14 R 62431)

0.625 0.812 0.094 HM3 R 6105
0.813 0.094 HM3 V 6106
0.933 0.188 HM14 R 61251)

0.933 0.188 HM14 V 61261)
0.937 0.188 HM14 R 61301)
1.000 0.125 HM14 P 61521)

1.000 0.125 HM14 R 6153
1.063 0.250 HM14 R 61581)

1.124 0.250 HM14 R 62251)
1.250 0.250 HM14 R 63231)
1.259 0.250 HM14 R 63351)

1.375 0.250 HM14 R 63701)
0.669 1.250 0.250 HM14 R 68061)

0.688 0.999 0.188 HM14 R 67201)
1.124 0.250 HM14 R 67591)
1.187 0.125 HM14 R 67621)
1.375 0.125 HM14 R 69151)
1.375 0.250 HM14 R 69201)

0.750 0.999 0.125 HM14 R 7410
1.000 0.125 HM14 D 74081)
1.000 0.125 HM3 V 535909
1.004 0.156 HM8 R 7409
1.006 0.125 HM14 R 74111)
1.031 0.313 HMA6 R 7412

1.062 0.188 HM14 R 7413
1.124 0.156 HM14 R 74151)

1.187 0.156 HM14 R 7421
1.249 0.250 HM14 R 5307162)

1.250 0.250 HM14 R 74641)
1.259 0.250 HM14 R 74771)
1.375 0.250 HM14 R 7536

1.375 0.250 HM14 P 7537
1.437 0.250 HM14 R 75501)
1.499 0.250 HM14 R 75711)

2) Stainless steel case

d1 0.781 – 1.375 in.
b
B3
b
d1 D d1 D

seal width
d1 D b B3
in. – –
0.781 1.375 0.197 HM14 R 78311)

0.813 1.063 0.125 HM3 R 8009

0.875 1.125 0.125 HM14 R 8620
1.125 0.125 HM14 V 86191)
1.246 0.188 HM14 R 86251)

1.251 0.188 HM14 R 8627
1.251 0.188 HM3 R 86312)
1.255 0.188 HM14 R 86321)
1.308 0.250 HM14 R 86371)

1.312 0.250 HM14 R 86451)
1.375 0.188 HM14 R 86771)
1.437 0.250 HM14 R 86901)

1.499 0.250 HM21 R 87411)
1.562 0.250 HM14 R 8761

1.575 0.250 HM14 R 8772
1.624 0.188 HM8 R 8802

0.938 1.375 0.250 HM14 R 92431)
1.499 0.250 HM14 R 92981)
1.734 0.250 HM14 R 93541)

1.000 1.250 0.125 HM14 R 98151)
1.312 0.125 HM14 R 98181)
1.375 0.188 HM14 R 98201)
1.437 0.250 HM14 R 98351)

1.499 0.188 HM14 R 98591)
1.510 0.219 HM21 R 98531)
1.561 0.250 HM14 R 99001)

1.575 0.250 HM14 R 99031)
1.624 0.250 HM14 R 99321)


seal width
d1 D b B3
in. – –
1.000 1.752 0.250 HM21 R 99951)

cont. 1.781 0.250 HM21 R 530484

1.781 0.469
1.781 0.469 0.265
HM14 R
HM18 R
100341)
100351)
2.6
1.851 0.250 HM14 R 100741)
1.938 0.250 HM14 R 101121)
2.000 0.250 HM21 R 101521)

2.250 0.250 HM14 R 101851)

1.125 1.375 0.125 HM14 R 11050
1.375 0.125 HM14 V 110521)
1.438 0.203 HM14 R 110551)

1.499 0.188 HM14 R 110601)
1.562 0.188 HM8 R 11065

1.562 0.250 HM14 R 11081
1.624 0.250 HM21 R 111301)
1.750 0.250 HM14 R 111501)

1.781 0.250 HM21 R 111611)
1.781 0.469 0.265 HM18 R 11164
1.828 0.250 HM21 R 11191

1.938 0.343 0.352 HM14 R 11269
2.000 0.250 HM21 R 113341)

2.047 0.250 HM21 R 113521)

1.188 2.000 0.250 HM1 R 11836

1.190 1.996 0.250 HM1 R 118461)

1.250 1.500 0.125 HM14 R 123301)
1.624 0.250 HM14 R 123251)
1.625 0.188 HM14 R 11096

1.686 0.188 HM14 R 123341)
1.752 0.188 HM21 R 123611)
1.752 0.250 HM21 R 12369

1.828 0.188 HM8 R 12375
1.874 0.250 HM21 R 123791)
1.968 0.438 HM14 R 123981)

1.968 0.469 0.254 HM18 R 123991)
1.979 0.250 HM21 R 124071)
1.979 0.406 0.200 HM18 R 12411

1.980 0.406 HMA22 R 125061)
1.983 0.250 HM21 R 12437
2.000 0.250 HM21 R 124811)

2.062 0.250 HM21 R 125081)
2.125 0.250 HM21 R 125651)

2.250 0.250 HM14 R 125821)
2.328 0.500 0.286 HM18 R 126111)

1.375 1.750 0.197 HM14 R 13529
1.750 0.197 HM14 V 135091)

d1 1.375 – 1.750 in.
b
B3
b b
d1 D d1 D d1

seal width
d1 D b B3
in. – –
1.375 1.834 0.188 HM8 R 135331)

cont.
1.874 0.188 HM14 R 13543
1.874 0.250 HM14 R 135481)
1.874 0.250 HM14 P 135451)
1.938 0.250 HM14 R 135561)

2.000 0.250 HM21 R 135731)
2.106 0.250 HM21 R 136121)
2.125 0.250 HM21 R 136621)

2.250 0.250 HM14 R 136891)
2.282 0.250 HM14 R 137101)
2.328 0.406 0.188 HM18 R 13711

2.374 0.250 HM21 R 137581)
2.437 0.250 HM21 R 137961)
2.502 0.250 HM21 R 138621)

2.835 0.594 TL8 R 139161)
1.438 2.000 0.125 HM4 R 14209

2.250 0.250 HM14 R 142571)
2.437 0.250 HM21 R 143591)
2.437 0.250 HM21 V 5643651)
1.457 2.047 0.328 HMA11 R 146002)
1.473 1.971 0.563 HMA10 R 14631
1.500 1.874 0.188 HM14 R 14804

1.874 0.188 HM14 V 148081)
1.874 0.250 HM14 R 148101)
1.938 0.250 HM14 R 148161)

1.983 0.188 HM14 R 14840
1.989 0.250 HMA22 R 148481)

2) Press-fit width 0.288 in., axial auxiliary lip

seal width
d1 D b B3
in. – –
1.500 2.000 0.188 HM8 R 14869

cont. 2.000 0.250 HM14 R 148571)
2.250 0.250 HM21 R 14960

2.6
2.254 0.250 HM21 R 149661)
2.328 0.390 0.188 HM18 R 14975

2.328 0.500 0.286 HM18 R 14974
2.374 0.250 HM21 R 150321)
2.437 0.250 HM14 R 150801)

2.502 0.250 HM21 R 151601)
2.623 0.250 HM21 R 15190
2.716 0.250 HM21 R 152091)

1.563 2.250 0.250 HM14 R 155321)
2.374 0.250 HM21 R 155441)
2.502 0.250 HM21 R 156491)
2.687 0.250 HM21 R 157191)

1.609 1.906 0.250 HM3 R 164302)

1.625 2.125 0.250 HM14 R 160551)
2.250 0.250 HM21 R 160651)
2.328 0.438 0.235 HM18 R 160691)

2.328 0.438 TL7 R 16064
2.374 0.250 HM21 R 160921)
2.375 0.250 HM14 R 16095
2.437 0.250 HM21 R 161681)

2.502 0.250 HM21 R 162701)
2.562 0.250 HM21 R 162851)
2.562 0.438 0.210 HM18 R 162891)
2.623 0.250 HM21 R 163221)

2.750 0.250 HM21 R 163621)
2.781 0.313 HM14 R 163841)
1.660 2.440 0.594 HM11 R 16520
1.688 2.328 0.500 0.286 HM18 R 16667

2.502 0.281 HM21 R 167431)
2.562 0.250 HM21 R 167541)
1.750 2.250 0.188 HM14 R 172401)

2.374 0.250 HM21 R 17277
2.437 0.250 HM21 R 17310

2.441 0.250 HM21 R 173401)
2.441 0.250 HM21 R 173411)2)
2.441 0.469 0.254 HM18 R 173591)
2.502 0.250 HM21 R 173921)

2.561 0.250 HM21 R 174151)
2.562 0.500 0.286 HM18 R 174061)
2.623 0.250 HM21 R 17461
2.716 0.250 HM21 R 174881)

2.718 0.359 0.160 HM18 R 176171)
2.718 0.359 TL7 R 17618
2.750 0.250 HM21 R 175441)
2.830 0.375 HM21 R 176331)

2.875 0.250 HM21 R 176711)
2.875 0.500 TL7 R 17674

d1 1.750 – 2.500 in.
b
B3
b b
d1 D d1 D d1

seal width
d1 D b B3
in. – –
1.750 3.000 0.250 HM21 R 177021)

cont.
3.149 0.290 TL6 R 17724
1.781 2.126 0.250 HM14 R 178022)
1.811 2.697 0.295 HMA8 R 17955
1.813 2.562 0.438 0.224 HM18 R 180501)

2.719 0.270 TL7 R 18127
2.965 0.250 HM1 R 18258
1.875 2.502 0.250 HM21 R 185581)

2.623 0.250 HM21 R 185911)
2.750 0.250 HM21 R 186591)
2.780 0.250 HM21 R 187041)

2.875 0.250 HM21 R 187501)
2.997 0.250 HM14 R 188081)
3.000 0.250 HM21 R 188231)

3.150 0.250 HM21 R 188891)
1.938 2.502 0.281 HM14 R 192191)

2.875 0.250 HM21 R 193061)
2.686 0.594 TL8 R 192511)
1.945 2.892 0.294 TL6 R 195101)
1.970 2.362 0.158 HM14 D 532627
2.000 2.371 0.250 HM14 R 197371)

2.375 0.188 HM14 R 19733
2.500 0.250 HM1 R 19748

2.502 0.250 HM14 R 197541)


seal width
d1 D b B3
in. – –
2.000 2.623 0.250 HM21 R 197631)

cont. 2.623 0.250 HM21 V 197461)

2.631 0.272
2.635 0.234
HMA94 R
HM14 R
200162)
197701)
2.6
2.686 0.250 HM21 R 197831)
2.750 0.250 HM21 R 198341)

2.752 0.188 HM14 R 198201)
2.875 0.250 HM21 R 198801)

2.965 0.313 HM14 R 199401)
2.965 0.500 0.275 HM14 R 199381)
2.997 0.250 HM21 R 19965
3.000 0.250 HM21 R 200061)

3.061 0.250 HM21 R 200441)
3.148 0.250 HM14 R 20078
3.623 0.250 HM21 R 20148
2.063 3.149 0.500 TL6 D 206721)3)

3.150 0.266 TL7 R 20674
2.094 2.718 0.359 0.160 HM18 R 209521)

2.750 0.250 HM21 R 209201)
2.125 2.750 0.250 HM21 R 210591)

2.875 0.250 HM14 R 211011)
2.891 0.250 HM14 R 211211)
3.000 0.250 HM21 R 211591)

3.061 0.250 HM21 R 212081)
3.189 0.250 HM21 R 212651)
2.240 3.189 0.610 HM14 R 226141)
2.250 2.625 0.188 HM14 R 223061)

2.875 0.250 HM21 R 22325
3.000 0.250 HM21 R 223681)

3.061 0.250 HM21 R 22392
3.125 0.563 0.214 HM18 R 22411

3.251 0.250 HM21 R 22468
3.440 0.250 HM14 R 225651)
2.297 3.148 0.359 0.185 HM18 R 22870
2.313 3.000 0.250 HM14 R 230351)

3.065 0.281 HM1 R 23098
3.500 0.250 HM21 R 232401)
2.375 2.997 0.250 HM21 R 236301)

3.000 0.250 HM21 R 23640
3.350 0.250 HM21 R 237251)
3.543 0.250 HM21 R 238151)
2.500 3.000 0.313 HM1 R 24865

3.000 0.250 HM14 R 248631)
3.125 0.250 HM21 R 248751)

3.150 0.250 HM21 R 248801)
3.251 0.250 HM21 R 249041)

3.500 0.250 HM21 R 250071)

2) Press-fit width 0.257 in.

d1 2.625 – 9.500 in.
b b
d1 D d1 D

seal width
d1 D b B3
in. – –
2.625 3.371 0.250 HM14 R 261441)

3.623 0.250 HM21 R 262601)
3.751 0.715 TL4 RR 262892)
3.813 0.415 TL5 R 263103)
2.750 3.125 0.188 HM1 R 27210

3.250 0.313 HM1 R 27225
3.500 0.250 HM14 R 272711)

3.500 0.250 HM14 V 5467511)
3.751 0.250 HM21 R 273941)
2.875 3.751 0.250 HM21 R 287001)

3.876 0.188 HM1 R 287251)
3.876 0.250 HM21 R 287511)
4.003 0.250 HM21 R 288001)
2.953 4.724 0.320 TL1 R 298521)
3.000 3.500 0.313 HM1 R 29840

3.623 0.250 HM14 R 29850
3.751 0.250 HM21 R 298631)
4.000 0.250 HM21 V 539075

4.003 0.250 HM21 R 29968
4.249 0.250 HM21 R 300491)
3.125 3.751 0.250 HMA1 R 311291)

4.125 0.250 HMA1 R 31192
3.250 3.750 0.250 HMA1 R 323251)

4.249 0.250 HM14 R 324121)
4.501 0.250 HM21 R 325101)


seal width
d1 D b B3
in. – –
3.500 4.000 0.300 HM1 R 34835

4.003 0.250 HM14 R 348401)
4.125 0.250 HM14 R 34848

2.6
4.125 0.250 HM14 V 5467701)
4.450 0.531 HM12 R 34885

4.501 0.250 HM21 R 34967
4.751 0.250 HM21 R 350421)
3.750 4.376 0.250 HM14 R 373201)

4.376 0.250 HM14 V 373251)
4.000 4.501 0.250 HM14 R 398351)

4.501 0.250 HM14 V 5463871)
4.876 0.250 HM21 R 398601)
4.999 0.250 HM21 R 399611)
4.250 4.813 0.313 HM14 R 42340

5.126 0.250 HM21 R 423801)
5.251 0.250 HM21 R 424701)
4.500 5.501 0.250 HM14 R 45025
4.750 5.375 0.313 HM14 R 473781)
4.875 5.501 0.250 HM14 R 48650
5.000 6.250 0.250 HM21 R 500701)
5.250 6.250 0.250 HM4 R 52475
5.750 6.375 0.250 HMA1 R 57502

7.003 0.250 HMA21 R 57571
6.000 7.500 0.250 HM4 R 60075
6.374 8.749 0.421 HMA96 R 181948
7.938 8.750 0.344 HM14 R 79302
9.500 10.750 0.313 HM21 R 95052
Radial shaft seals
X seals, sealing against housing bore

SKF offers an assortment of radial shaft seals
that have a press fit on the shaft and with seal-
ing lip(s) that contact the housing bore. For a X1
proper press fit, the requirements specified for
housing bores on pages 74 to 76 should be
adhered to for the shaft. Shaft requirements
specified on pages 70 to 72 apply for the hous-
ing bore when using X seals. These seals are
generally installed with the sealing lip(s) facing X2
outward to provide optimum exclusion. Main
applications are greased lubricated agriculture
machinery. The selection to the right shows the
most commonly used SKF designs. Contact SKF
for more information on available designs.
See matrix 1 on pages 90 and 91 for general X4
X12
X13
X14
X15
XH15
Radial shaft seals – X seals – metric dimensions

d1 25,40 – 82,55 mm
d1 D
2.7
For proper press fit on shaft, refer to housing bore tolerances specified on pages 74 to 76.

seal width
d1 D b
mm – –
25,40 59,84 6,86 X15 R 538266

38,10 55,55 12,70 X1 L 14896
58,06 6,86 X15 R 14970
58,06 10,67 XH15 R 14971
62,53 7,37 X13 R 15174

39,70 56,82 7,37 X4 R 15530
64,29 7,24 X15 R 15660
69,85 11,13 X R 15702

41,28 62,53 6,35 X15 R 16286

42,88 67,31 7,37 X4 R 16818

44,45 69,04 7,47 X4 R 17485
70,76 7,47 X15 R 17620

46,05 61,16 7,62 X15 R 18030

47,57 68,99 7,14 X13 R 18630

50,57 73,66 7,37 X4 R 19720

50,80 71,17 6,35 X15 D 19844
73,03 6,50 XHM R 19882

53,98 82,55 6,86 X15 R 21298

57,15 86,36 7,47 X15 R 22563

63,40 93,27 7,95 X15 R 25078

76,20 101,60 12,70 X2 L 29900
114,94 9,53 X12 R 30108

80,00 101,45 15,00 X15 R 31514

82,55 113,49 8,00 X4 R 32437
114,30 7,95 X15 R 32441

Radial shaft seals – X seals – metric dimensions

d1 86,36 – 158,75 mm
d1 D

seal width
d1 D b
mm – –
86,36 114,30 7,14 X14 V 340001)

92,08 114,30 7,47 X15 R 36172

98,43 136,91 9,53 X12 R 38590

101,60 147,65 12,70 X R 40131

111,13 136,47 14,48 X1 P 44269

114,30 152,78 13,97 X12 R 44892
162,79 10,54 X12 D 45161

120,65 152,45 7,62 X15 R 47455

139,70 172,21 9,65 X R 55152

158,75 196,85 8,89 X R 62530
1) SKF Bore Tite Coating on inside diameter
Radial shaft seals – X seals – inch dimensions

d1 1.000 – 3.250 in.
d1 D
2.7

seal width
d1 D b
in. – –
1.000 2.356 0.270 X15 R 538266

1.500 2.187 0.500 X1 L 14896
2.286 0.270 X15 R 14970
2.286 0.420 XH15 R 14971
2.462 0.290 X13 R 15174

1.563 2.237 0.290 X4 R 15530
2.531 0.285 X15 R 15660
2.684 0.438 X R 15702

1.625 2.462 0.250 X15 R 16286

1.688 2.650 0.290 X4 R 16818

1.750 2.718 0.294 X4 R 17485
2.786 0.294 X15 R 17620

1.813 2.408 0.300 X15 R 18030

1.873 2.716 0.281 X13 R 18630

1.991 2.900 0.290 X4 R 19720

2.000 2.802 0.250 X15 D 19844
2.875 0.256 XHM R 19882

2.125 3.250 0.270 X15 R 21298

2.250 3.400 0.294 X15 R 22563

2.496 3.672 0.313 X15 R 25078

3.000 4.000 0.500 X2 L 29900
4.525 0.375 X12 R 30108

3.150 3.994 0.591 X15 R 31514

3.250 4.468 0.315 X4 R 32437
4.500 0.313 X15 R 32441

Radial shaft seals – X seals – inch dimensions

d1 3.400 – 6.250 in.
d1 D

seal width
d1 D b
in. – –
3.400 4.500 0.281 X14 V 340001)

3.625 4.500 0.294 X15 R 36172

3.875 5.390 0.375 X12 R 38590

4.000 5.813 0.500 X R 40131

4.375 5.373 0.570 X1 P 44269

4.500 6.015 0.550 X12 R 44892
6.409 0.415 X12 D 45161

4.750 6.002 0.300 X15 R 47455

5.500 6.780 0.380 X R 55152

6.250 7.750 0.350 X R 62530
1) SKF Bore Tite Coating on inside diameter
2.7
Radial shaft seals
Seals for heavy industrial applications, selected main designs, self-retaining (open housing)
Standard design Other basic designs Material Operating temperature range Pressure
(preferred design) code differential
from to from to
– °C °F MPa (psi)
R –40 +100 –40 +210 0

D –40 +100 –40 +210
H –40 +150 –40 +300
V (HDS6 only) –40 +200 –40 +390
HDS7 HDS6
R –40 +100 –40 +210 0,1

H –40 +150 –40 +300 (15)
V –40 +200 –40 +390
HDL HDLA
R –40 +100 –40 +210 0,1

V –40 +200 –40 +390 (15)
SBF
R –40 +100 –40 +210 0,1

D –40 +100 –40 +210 (15)
H –40 +150 –40 +300
V –40 +200 –40 +390
HDS2 HDS1 HDS4
R –40 +100 –40 +210 0,1

D –40 +100 –40 +210 (15)
H –40 +150 –40 +300
V –40 +200 –40 +390
HDSA2 HDSA1 HDSB2
HDSB1
R –40 +100 –40 +210 0,1

D –40 +100 –40 +210 (15)
H –40 +150 –40 +300
V –40 +200 –40 +390
HDSE2 HDSE1 HDSD2
HDSD1
Matrix 2
Shaft-to-bore Dynamic Maximum shaft Ease of Retention and exclusion ability

misalignment runout surface speed installation
(STBM) TIR (DRO) TIR
mm (in.) mm (in.) m/s (ft/min) – –
1,6 2,4 25 Excellent Highly effective exclusion of water

2
(0.062) (0.093) (4 900) and solid contaminants and excellent
retention of grease
2,5 2,4 24 Good Excellent retention of light oils, even

(0.1) (0.093) (4 700) at high surface speeds and
25 misalignment
(4 900)
35
(6 900)
1,5 2,4 25 Excellent Excellent oil or grease retention

(0.06) (0.093) (4 900)
1,6 2,4 25 HDS2, HDS4: Excellent oil or grease retention

(0.062) (0.093) (4 900) Excellent
HDS1:
Good
1,6 2,4 25 Excellent to good, HDSA/B: Excellent oil or grease

(0.062) (0.093) (4 900) varies with equipment retention and exclusion of light to
design moderate contaminants
1,6 2,4 25 HDSD2/HDSE2: Excellent oil or grease retention and

(0.062) (0.093) (4 900) Excellent exclusion of light to moderate
contaminants or separation of two
media
HDSD1/HDSE1: Good grease retention, increased

Good protection against contaminants
Continued †
Radial shaft seals
Seals for heavy industrial applications, selected main designs, axially compressed (housing with cover plate)
Standard design Other basic designs Material Operating temperature range Pressure
(preferred design) code differential
from to from to
– °C °F MPa (psi)
R –40 +100 –40 +210 0,07

D –40 +100 –40 +210 (11)
H –40 +150 –40 +300
V –40 +200 –40 +390
HS5 HS4
R –40 +100 –40 +210 0

D –40 +100 –40 +210
H –40 +150 –40 +300
V –40 +200 –40 +390
HS8 HS6 HS7
R –40 +100 –40 +210 0,03

V –40 +100 –40 +390 (5)
HSF5 HSF6 HSF7
HSF8 HSF9
R –40 +100 –40 +210 0

V –40 +200 –40 +390
HSF1 HSF2 HSF3
HSF4
cont. matrix 2
Shaft-to-bore Dynamic Maximum shaft Ease of Retention and exclusion ability

misalignment runout surface speed installation
(STBM) TIR (DRO) TIR
mm (in.) mm (in.) m/s (ft/min) – –
1,6 2,4 HS4: 15 (2 950) Good HS4, HS5: Good oil retention
2
(0.062) (0.093) HS5: 13 (2 560)
1,6 2,4 HS6: 10 (1 970) HS6: Fair HS6, HS8: Good to excellent oil
(0.062) (0.093) HS7: 7,5 (1 480) HS7: Excellent or grease retention
HS8: 10 (1 970) HS8: Good HS7: Good (grease retention only)
1,5 2,4 15 (2 950) Good to excellent Excellent oil retention

(0.06) (0.093) depending on the
operating conditions
1,5 2,4 15 (2 950) Fair to good depending Good to excellent oil retention
(0.06) (0.093) depending on the on the available space
operating conditions for installation
Radial shaft seals
Seals for heavy industrial Fig. 33
applications
General
Heavy industries like metal, construction, wind
energy, forestry, mining and pulp and paper pro-
vide a challenging environment for radial shaft
seals. Operating within a wide range of speeds,
temperatures and environmental conditions, HDS7
these seals need to reliably retain lubricants while
preventing harsh contaminants from entering
the system. The HDS7 seal features an optimized non-
SKF seals for heavy industrial applications spring-loaded lip profile, designed to retain
are available in a wide assortment of designs grease and aggressively pump contaminants
and materials to meet the varying demands of away from the lip. The lip concept of HDS7 seals
each challenging application. The assortment also reduces radial loads, which otherwise can
includes heavy-duty metal-cased seals, rubber lead to elevated underlip temperatures and
outside diameter seals with metal inserts or increased seal wear. HDS7 seals are installed
fabric-reinforcement and all-rubber seals. To with the sealing lip facing the air side. The HDS7
simplify seal selection, table 18 on page 213 can also be used in oil lubricated applications in
can be used for general guidance. See also back-to-back arrangements with a spring-loaded
matrix 2 on pages 198 to 201. seal design, e.g. an HDS1 or HDS2 († figs. 35
and 36), in the includer position.
HDS7 seals can also be equipped with a PTFE
Metal-cased seals auxiliary lip positioned and directed as shown in
fig. 42 on page 206 and/or with an elastomer
General applied to the metal outside diameter († fig. 43
SKF metal-cased seals are specially designed to on page 206).
withstand the extreme conditions encountered The HDS7 seal is available with a nitrile seal-
in heavy-duty applications. The designs include ing lip for general use, SKF Duralip for increased
the highly engineered HDS7, the high-perform- wear resistance in abrasive environments and
ance HDL seals and the commonly used HDS1 SKF Duratemp that combines improved wear
and HDS2 seals as well as the HDSA, B, C, D and resistance with increased temperature capability.
E seals. These seals perform exceptionally well For certain applications, SKF Duralife can also
in the very contaminated environment of metal be specified. See page 30 for additional infor-
rolling mills, the high-speed and high-tempera- mation about different sealing lip materials.
ture environment of paper mills, as well as more Spacer lugs are available as an option. See
universal applications like industrial gearboxes. page 211 for additional information.
HDS7 seals are available for all shaft diameters
HDS7 within the ranges listed in table 19 on page 214.
The ingress of water and solid contaminants is The product tables, starting on page 216, list
a common cause of bearing failures. To solve this, a selection of sizes. Contact your SKF sales
SKF developed the HDS7 seal with enhanced representative for additional information.
exclusion capabilities († fig. 33). It was origi-
nally designed for grease lubricated bearings in
rolling mill stands, where water and scale are a
constant threat to bearing service life. The HDS7
is also recommended for use in large gearboxes,
coal pulverizers and cement grinders. Customers
have reported that the HDS7 seal is easier to in-
stall and provides longer service life than similar
seal designs.
HDL seals Fig. 34
HDL seals († fig. 34) are premium metal-cased

radial shaft seals for oil lubricated applications.
They are specially designed for tough operating
conditions including high speeds and tempera-
tures, considerable runout and/or misalignment.
The high-speed performance characteristics of
HDL seals make them an excellent choice for the
severe operating conditions encountered in the 2
rolls of paper-making machines. HDL
HDL seals feature the combination of a stain-
less steel garter spring and individual stainless
Fig. 35
steel finger springs around the entire circumfer-
ence of the seal. This spring combination en
ables the seal to work effectively and provides
long service life, even under severe operating
conditions.
HDLA seals are designed with an elastomeric
auxiliary lip for added protection against
contaminants.
Both HDL and HDLA seals are available with a
sealing lip made of either nitrile rubber, hydrogen- HDS1
ated nitrile rubber or fluoro rubber († page 31).
These materials enable the seals to perform
Fig. 36
well under a variety of operating speeds and
temperatures. Fixed-width spacer lugs are
available for both HDL and HDLA seals on a
quotation basis.
A selection of available sizes is listed in the
product tables starting on page 226. Contact
your SKF sales representative for additional
information regarding availability.
HDS1 and HDS2 HDS2

The most commonly used metal-cased seals are
the HDS1 and HDS2 seals, designed for general-
purpose applications. They are equipped with Nitrile rubber is standard for these seal designs,
a heavy-duty metal case and a stainless steel but both of them are also available in SKF Duralip,
garter spring. SKF Duratemp and SKF Duralife.
The HDS1 seal († fig. 35) has a spring in- The HDS1 and HDS2 seals are available for
stalled in the SKF Springlock groove († fig. 56 all shaft diameters within the ranges listed in
on page 212). For blind installations, where table 19 on page 214. The product tables start-
spring displacement may go undetected, HDS2 ing on page 242 list a selection of sizes. Contact
seals († fig. 36) have an SKF Springcover your SKF sales representative for additional
(† fig. 57 on page 212) that retains the spring information.
in the groove. The HDS1 and HDS2 seals are
available with adjustable or fixed-width spacer
lugs († page 211).
The HDS1 and HDS2 seals can be designed
with a PTFE auxiliary lip, positioned and directed
in either of the two ways shown in figs. 41 and
42 and/or with an elastomer applied to the metal
outside diameter († fig. 43 on page 206).
Radial shaft seals
HDSA and HDSB eals Fig. 37
HDSA and HDSB seals are designed with an

elastomeric auxiliary lip in addition to the seal-
ing lip († figs. 37 to 38). They are generally
used where additional protection from contami-
nants is needed and where there is insufficient
space for more than one seal.
The chamfer on the auxiliary lip of an HDSA
seal faces the sealing lip, enabling easier shaft
installation from the sealing lip direction. The HDSA2
chamfer of the auxiliary lip of HDSB seals faces
away from the sealing lip, enabling easier shaft
Fig. 38
installation from the other direction. The disad-
vantage is, however, a slightly reduced exclusion
ability.
HDSA2 and HDSB2 seals are designed with
an SKF Springcover, while HDSA1 and
HDSB1 seals are designed without an SKF
Springcover († fig. 57 on page 212).
HDSA and HDSB seals can also be designed
with an elastomer applied to the metal outside
diameter († fig. 43 on page 206). HDSB1
HDSA and HDSB seals are available with
sealing lips made of nitrile rubber, SKF Duralip,
SKF Duratemp or SKF Duralife. For shaft diam-
eters up to 1 200 mm (47 in.), the standard
auxiliary lip is made of SKF Duralip.
These seals are available for all shaft diam-
eters within the ranges listed in table 19 on
page 214. Also, see the product tables starting
on page 264 for a selection of sizes. Contact
your SKF sales representative for additional
information.
HDSD and HDSE seals Fig. 39
HDSD seals († fig. 39) are designed with two

sealing lips facing opposite directions. These
seals are typically used in applications where
two fluids must be kept separated. When using
an HDSD seal, it is very important to provide a
means to lubricate the sealing lips. To do this,
the cavity between the sealing lips must be filled
with grease prior to installation and/or during 2
operation via lubrication holes drilled through HDSD1
the metal case into the cavity.
HDSE seals († fig. 40) feature two sealing
Fig. 40
lips facing the same direction. They are typically
used when a back-up seal would otherwise be
needed for retention or exclusion purposes. Like
HDSD seals, HDSE seals must be equipped with
a means to lubricate the sealing lips so that the
seal functions properly.
HDSD and HDSE seals are available with an
SKF Springcover (HDSD2, HDSE2) or without an
SKF Springcover (HDSD1, HDSE1) († fig. 57
on page 212). All of them are available in nitrile HDSE1
rubber, SKF Duralip, SKF Duratemp or SKF
Duralife.
HDSE seals can also be designed with a PTFE
auxiliary lip positioned and directed in either
of the two ways shown in figs. 41 and 42 on
page 206.
HDSD and HDSE seals are available for all
shaft diameters within the ranges listed in
table 19 on page 214. The product tables
starting on page 272 list a selection of sizes.
Contact your SKF sales representative for
additional information.
Radial shaft seals
Additional design options Fig. 41
HDS1, HDS2, HDS7 and HDSE seals can be de-

signed with an auxiliary PTFE lip to further protect
the bearing and sealing lip(s) from dust particles air side
in heavily contaminated environments, for ex-
ample mining and cement industries. The PTFE
lip is then positioned and directed as shown in
fig. 41.
The PTFE lip can also be positioned and dir oil side
ected to provide additional lubricant retention HDSF2
(† fig. 42).
The PTFE lip is clamped between the metal
Fig. 42
case and the rubber seal body without signifi-
cantly increasing the total seal width. It has very
good chemical and wear resistance, can with-
stand dry running and contributes to improved air side
sealing performance while only generating a
minimal friction torque. The combination of a
PTFE auxiliary lip and a sealing lip made of the
fluoro rubber compound SKF Duralife, developed
by SKF, creates a particularly effective sealing oil side
solution. HDSH2
Special care must be taken to prevent dam-
aging the PTFE lip during installation. Refer to
Fig. 43
instructions in paragraph PTFE seals on page 85.
The letters F and H in the product name indi-
cate a PTFE auxiliary lip design including the
lip’s position and direction; see for example the air side
HDSF2 († fig. 41) and HDSH2 († fig. 42).
HDS1, HDS2 and HDS7 seals (with or without
an auxiliary PTFE lip) as well as the HDSA and
HDSB seals are available with an elastomer ap-
plied to the outside diameter for use in applica-
tions where bore temperatures reach maximum HDS2K oil side
100 °C (210 °F) († fig. 43). This design feature

has several important advantages:
• Compensates for imperfections in the housing

bore surface, improving the sealing perform-
ance by minimizing bypass leakage.
• Prevents contaminants from entering
through gaps between housing bore and
the seal outside diameter at, for example,
out-of-round conditions.
• Minimizes the risk of damage to the housing
bore during installation and removal.
This design option is indicated by the letter K

in the product name; see for example the HDS2K
(† fig. 43).
Rubber outside diameter seals Fig. 44
General
The assortment of SKF rubber outside diameter
seals includes metal-inserted, fabric-reinforced
and all-rubber designs. The fabric-reinforced
and all-rubber seals are available in solid and
split designs.
Rubber outside diameter seals offer a number 2
of important operating and installation benefits SBF
and are especially suitable for split housings.
The rubber prevents damage to the housing
Fig. 45
bore during installation, which otherwise can
cause bypass leakage. Compared to metal-cased
seals, rubber outside diameter seals can tolerate
higher surface roughness in the housing bore.
They also resist corrosion and do not seize in the
bore, even years after installation.
As a result of lower press-in forces, rubber
outside diameter seals are often easier to install
than metal-cased seals. They can be installed by
hand or with simple tools even when the diam- HDS4
eters are very large. This is especially true of the
fabric-reinforced and all-rubber designs. Fur-
Fig. 46
thermore, in the case of split seals, there is no
need to remove the shaft or other machine
components when replacing the seal.
SBF metal-inserted seals

SBF seals († fig. 44) are spring-loaded and
designed with a flexible metal stiffening ring
that enables the seal to be installed without the
use of a cover plate. SBF seals can be used as
an upgrade to fabric-reinforced seals in many HDS6
applications that are either grease or oil lubri-
cated. SBF seals are available in both nitrile and
fluoro rubber. A selection of available sizes is Both types are made standard of nitrile rubber.
listed in the product tables starting on page 274. They are also available in any of the sealing lip
Contact your SKF sales representative for materials used for the metal-cased HDS seals.
additional information regarding availability. Both HDS4 and HDS6 seals are equipped with
moulded 12,7 mm (0.5 in.) spacer lugs that can
HDS4 and HDS6 metal-inserted seals be trimmed or removed if necessary.
HDS4 seals († fig. 45) feature a patented Contact your SKF sales representative for
moulded-in garter spring that cannot be dis information regarding availability.
placed during installation. They also provide
very good oil retention while minimizing wear
on the shaft. HDS4 seals are typically used in
the high-speed applications found in the pulp
and paper industry. HDS6 seals († fig. 46)
are similar in design to HDS4 seals but do not
contain a garter spring. HDS6 seals are designed
for grease retention.
Radial shaft seals
HSF fabric-reinforced seals Fig. 47
The spring-loaded HSF seal assortment con-

sists of the HSF5, HSF6, HSF7 and HSF8 solid
seals and their split versions, HSF1, HSF2, HSF3
and HSF4 seals († figs. 47 to 49). There is also
a pressure profile seal, HSF9, available in the
solid version only. These seals are mainly used
in heavy-duty applications like gear drives, pro-
peller shafts, cold and hot mill work rolls,
pumps, paper machinery, etc. HSF1, HSF5
HSF5, HSF6 and HSF7 seals have a strong,
flexible, fabric-reinforced rubber back instead
Fig. 48
of a metal case. HSF5 seals have a basic single-
lip design. HSF6 seals are equipped with radial
lubrication grooves in the back of the seal and
HSF7 seals include a circumferential lubrication
groove. HSF4 and HSF8 seals are designed with
an auxiliary lip for additional protection against
contaminants.
Threaded spring connections are standard for
all HSF seals († fig. 54a on page 211). For the
split versions, a hook-and-eye connection can HSF2, HSF6
also be specified († fig. 54b on page 211).
All HSF seals are manufactured oversized
Fig. 49
relative to the housing bore diameter and depth
to enable proper compression and stability. A
cover plate is required to properly install and
apply all HSF seals († figs. 25 and 26 on
pages 82 and 83). The plate creates an axial
preload to provide reliable static sealing perform
ance. The plate should also avoid seal distortion
during installation. HSF seals are available in
nitrile rubber, hydrogenated nitrile rubber and
fluoro rubber materials. HSF3, HSF7
A selection of available HSF seal sizes is listed
in the product tables starting on page 276.
Contact your SKF sales representative for
additional information regarding availability.
HS all-rubber seals Fig. 50
HS seals, available in solid and split executions,

are all-rubber seals, designed without any re
inforcement. They are manufactured oversized
relative to the housing bore diameter and depth
to enable proper compression and stability. A
cover plate († figs. 25 and 26 on pages 82
and 83) is required to compress the seal axially,
helping to stabilize the seal in the housing bore. 2
A stainless steel garter spring located in the HS4
SKF Springlock groove († fig. 56 on page 212)
provides the appropriate radial load against the
Fig. 51
shaft.
For certain applications, HS seals are also
available with an auxiliary lip and/or band clamp.
Contact SKF for more information.
HS seals are available in nitrile rubber,
SKF Duralip, SKF Duratemp or SKF Duralife for
all shaft diameters within the ranges listed in
table 20 on page 215. Also, see the product
tables starting on page 302 for a selection of
sizes. Contact your SKF sales representative for HS5
additional information.
HS solid seals
Standard solid HS seals can accommodate shaft
diameters starting at 165 mm (6.5 in.) but
basically do not have an upper size limit.
HS4 seals († fig. 50) have a solid, all-rubber
design and incorporate a spring-loaded sealing
lip. They feature an SKF Springlock groove
(† fig. 56 on page 212) and are suitable for
both vertical and horizontal shafts. For a proper
fit in the housing bore, a cover plate is required
(† figs. 25 and 26 on pages 82 and 83).
HS5 seals († fig. 51) have the same basic
design as HS4 seals with the addition of an
SKF Springcover († fig. 57 on page 212) to
hold the spring in place during installation and
protect it from contaminants.
Both designs have a threaded spring con
nection († fig. 54a on page 211).
Radial shaft seals
HS split seals Fig. 52
In applications where shaft removal is impracti-

cal, HS all-rubber split seals are an excellent
choice. They are simply placed around the shaft
and pushed into the housing bore with the split
at the 12 o’clock position. A cover plate must be
used to compress the seal axially to stabilize it in
the housing bore.
HS split seals perform best with grease or
high-viscosity lubricants. However, low-viscosity HS6
lubricants are also suitable if the level of lubri-
cant is kept below the shaft centre line, which is
Fig. 53
particularly important at considerable surface
speeds. Split seals are preferably used on hori-
zontal shafts, but can also be used on vertical
shafts in grease lubricated applications.
HS6 seals († fig. 52) are designed with a
spring-loaded sealing lip and an SKF Springlock
(† fig. 56 on page 212). They feature a separ
ate loose spring and a hook-and-eye spring
connection for shaft diameters above 455 mm
(18 in.) unless otherwise specified († fig. 54b HS7, HS8
on page 211). Other sizes of HS6 seals come
with a threaded spring connection. For a proper
fit in the housing bore, a cover plate is required portion on either side of the split. HS8 seals
(† figs. 25 and 26, on pages 82 and 83). provide the most effective sealing performance
HS7 seals († fig. 53), designed for grease of all split HS seals and are the preferred design
lubricated applications only, have a spring-loaded for retaining low-viscosity lubricants and for
sealing lip and are designed with both an SKF water exclusion. HS8 seals perform best on
Springlock and SKF Springcover († figs. 56 horizontal shafts, but can also be used on ver
and 57 on page 212). All HS7 seals feature a tical shafts provided they are not flooded with
control-wire spring connection († fig. 54c on lubricant. For a proper fit, a cover plate is
page 211). The spring is completely enclosed required.
and the connection is made by running the con-
trol wire into the centre of the spring coil across Reinforced all-rubber HSS seals
the split (butt joint). A built-in spring tension SKF also offers a range of reinforced all-rubber
holds the sealing lip on the shaft. For a proper seals in nitrile rubber (NBR), SKF Duratemp
fit, a cover plate is required. Due to the unique (HNBR) and SKF Duralife (FKM). The standard
design that enables easier installation, a gap may grade of the material is used for the sealing lip,
occur at the joint even after the cover plate is while the part of the seal body contacting the
installed. It is necessary that the split be placed housing bore is made from a harder grade to
at the 12 o’clock position during installation. provide improved stability in operation and dur-
HS7 seals do not have the high-performance ing installation. For further information, refer to
characteristics of other HS seals, but are the publication Reinforced all-rubber HSS seals.
easiest to install.
HS8 seals († fig. 53) are designed with a
spring-loaded sealing lip, SKF Springlock, SKF
Springcover († figs. 56 and 57 on page 212)
and a hook-and-eye spring connection
(† fig. 54b on page 211) for shaft diameters
above 455 mm (18 in.). Other sizes of HS8 seals
come with a threaded spring connection. The
spring is entirely enclosed except for a small
Additional design features Fig. 54
Spring connections
Spring connections
There are different ways to connect the stainless
steel garter springs of HS and HSF seals. A
threaded spring connection († fig. 54a) is used
for all HSF seals unless otherwise specified and a
for the solid HS4 and HS5 seals as well as the
split HS6 and HS8 seals for shaft diameters 2
≤ 455 mm (18 in.). A hook-and-eye spring con-
nection († fig. 54b) is used for HS6 and HS8 b
seals for shaft diameters > 455 mm (18 in.). All
HS7 seals feature the special control-wire con-
nection († fig. 54c), available only for these
seals.
c
Spacer lugs
Spacer lugs are available for all metal-cased
Fig. 55
designs to separate seals in tandem or back-to-
back arrangements to provide space for sealing Spacer lugs
lip lubrication († fig. 55).
Traditional fixed-width lugs for metal-cased
HDS seals are 9,5 mm (0.375 in.) in diameter
and are available in widths from 3,2 mm
(0.125 in.) to 12,7 mm (0.5 in.) in increments
of 1,6 mm (0.063 in.). The fixed-width lug is an
available option for all metal-cased seals.
All standard adjustable lugs are 9,5 mm
(0.375 in.) in diameter and 9,5 mm (0.375 in.)
in width. They can be adjusted to smaller widths
in 1,6 mm (0.063 in.) increments by removing
the steel washers. The lugs may also be removed
entirely. Longer, adjustable lugs, with a width of
12,7 mm (0.5 in.), are available on request,
however, it can be more difficult to reduce their
width.
Table 17
Certain small seal cross sections may require
special small diameter lugs, 5,3 mm (0.210 in.), Number of spacer lugs needed
with a width range of 1,6 to 3,2 mm Spacer Housing bore diameter
(0.063 to 0.125 in.). lugs
The lugs are placed around the heel of the from incl. from incl.
seal in four, six or eight equally spaced locations, – mm in.

depending on the seal outside diameter
(† table 17). 4 762 30
Fixed-width lugs are available for HDL seals 6 762 1 143 30 45
on request.
8 1 143 45
Radial shaft seals
SKF Springlock Fig. 56
The SKF Springlock is a sealing lip feature that SKF Springlock

surrounds 270° of the garter spring diameter
(† fig. 56). It helps hold the spring in position
during installation and is standard on all HS seals
and spring-loaded, metal-cased HDS seals.
SKF Springcover
For blind installations, where spring displacement
may go undetected, the SKF Springcover
(† fig. 57) can be specified. It also protects the
spring from dirt, water and other contaminants.
SKF Springcover is flexible and covers the ex-
posed portion of the stainless steel garter spring
without adversely affecting the spring’s
capability.
Fig. 57
SKF Springcover
Table 18
Seals for heavy industrial applications, selection guide per application
Application General machinery Rolling mills, metals Industrial gearboxes Special machinery
Industrial gearboxes Hot strip mills General machinery Crushers, shredders, bailers, etc.
Cold rolled plate mills Rolling mills, paper mills
Industrial gearboxes
Type General purpose Water/scale exclusion High speed High Dynamic Runout (DRO) or
Shaft-To-Bore Misalignment
(STBM)
2
HDS1-2, HDSD-E 3 2 1 2
HDS4, 6 3 2 3 2
HDS7 2 3 1 2
HDSA-B 3 2 1 2
HDL 2 2 3 3
HS4-8 2 1 1 2
SBF, HSF1-9 3 2 1 2
1 = Good solution 2 = Better solution 3 = Best solution
Radial shaft seals
Table 19
Standard sections for metal-cased HDS seal designs
Designs with metal Shaft diameter Bore diameter Nominal Difference between
outside diameter seal width bore and shaft diameter
from to from to from to from to
– mm/in. mm/in. mm/in. mm/in.
HDS7 165,10 1 606,55 196,85 1 638,30 15,88 31,75 31,75 63,50

6.500 63.250 7.750 64.500 0.625 1.250 1.250 2.500
HDSH7 165,10 1 606,55 196,85 1 638,30 19,99 31,75 31,75 63,50

6.500 63.250 7.750 64.500 0.787 1.250 1.250 2.500
HDS1–3, HDSF1–3 165,10 1 606,55 196,85 1 638,30 15,88 31,75 31,75 76,20
6.500 63.250 7.750 64.500 0.625 1.250 1.250 3.000
HDSH1-3 165,10 1 606,55 196,85 1 638,30 19,99 31,75 31,75 76,20

6.500 63.250 7.750 64.500 0.787 1.250 1.250 3.000
HDSA1–2, HDSB1–2 165,10 1 189,74 196,85 1 219,20 21,36 38,10 31,75 76,20
6.500 46.840 7.750 48.000 0.841 1.500 1.250 3.000
HDSD1–2, HDSE1–2, 165,10 1 603,50 202,18 1 638,30 30,89 50,80 37,08 76,20
HDSEF1–2 6.500 63.130 7.960 64.500 1.216 2.000 1.460 3.000
HDSEH1–2 165,10 1 603,50 202,18 1 638,30 39,98 50,80 37,08 76,20

6.500 63.130 7.960 64.500 1.574 2.000 1.460 3.000
Designs with an elastomer Shaft diameter Bore diameter Nominal Difference between
applied to the outside seal width bore and shaft diameter
diameter
– mm/in. mm/in. mm/in. mm/in.
HDS7K 165,10 1 606,55 201,62 1 643,08 15,88 31,75 36,52 76,20

6.500 63.250 7.938 64.688 0.625 1.250 1.438 3.000
HDSH7K 165,10 1 606,55 201,62 1 643,08 19,99 31,75 36,52 76,20

6.500 63.250 7.938 64.688 0.787 1.250 1.438 3.000
HDS1–3K, HDSF1–3K 165,10 1 606,55 201,62 1 643,08 15,88 31,75 36,52 76,20
6.500 63.250 7.938 64.688 0.625 1.250 1.438 3.000
HDSH1–3K 165,10 1 606,55 201,62 1 643,08 19,99 31,75 36,52 76,20

6.500 63.250 7.938 64.688 0.787 1.250 1.438 3.000
HDSA1–2K, HDSB1–2K 165,10 1 606,55 201,62 1 643,08 15,88 31,75 36,52 76,20
6.500 63.250 7.938 64.688 0.841 1.250 1.438 3.000
Not all cross sections and widths are possible with every shaft diameter. Contact SKF for information
on dimensions at the e xtreme limits or for sizes outside the standard range.
Size options of metal-cased HDS seals

and all-rubber HS seals
All SKF metal-cased HDS seals and all-rubber
HS seals are made upon order in any inch or
metric size within the ranges listed in tables 19
and 20. Since new sizes are manufactured with-
out additional tooling, they can be supplied
without extended lead times. The product tables
starting on page 216 and 302, respectively, list 2
a selection of sizes. For any size that is not listed
in the product tables, contact your SKF distributor
or SKF sales representative.
Table 20
Standard size options of HS seals
Shaft diameter1) Bore diameter2) Bore depth3) Difference between

bore and shaft diameter
mm/in. mm/in. mm/in. mm/in.
165,10 4 572,00 190,50 4 597,40 12,70 25,40

6.500 180.000 7.500 181.000 0.500 1.000
165,10 4 572,00 195,10 4 602,00 12,70 19,99 30,00 50,80

6.500 180.000 7.681 181.181 0.500 0.787 1.181 2.000
330,20 4 572,00 368,30 4 610,10 16,51 25,40 38,10 63,50

13.000 180.000 14.500 181.500 0.650 1.000 1.500 2.500
1) Tolerance h11
2) Tolerance H8
3) Tolerance ±0,13 mm (0.005 in.)
Not all cross sections and widths are possible with every shaft diameter. Contact SKF for information
on dimensions at the extreme limits or on sizes outside the standard range.
Radial shaft seals – HDS7 – metric dimensions

d1 200 – 1 250 mm
The table includes only
a selection of sizes.
b For the full size range,
please refer to table 19
on page 214.
d1 D
Dimensions Design Lip Designation

Shaft Bore Nominal material
seal width
d1 D b
mm – – –
200 230 15 HDS7 R 200¥230¥15 HDS7 R
210 240 18 HDS7 D 210¥240¥18 HDS7 D1)
220 250 15 HDS7 R 220¥250¥15 HDS7 R
230 260 15 HDS7 R 230¥260¥15 HDS7 R
235 270 15 HDS7 H 235¥270¥15 HDS7 H

270 16 HDS7 H 235¥270¥16 HDS7 H
260 300 16 HDS7 R 260¥300¥16 HDS7 R
290 350 25 HDS7 R 290¥350¥25 HDS7 R
300 340 18 HDS7 R 300¥340¥18 HDS7 R

340 20 HDS7 R 300¥340¥20 HDS7 R
344 20 HDS7 R 300¥344¥20 HDS7 R
310 350 20 HDS7 R 310¥350¥20 HDS7 R
320 380 28 HDS7 R 320¥380¥28 HDS7 R
330 370 20 HDS7 R 330¥370¥20 HDS7 R
346 375 15 HDS7 R 346¥375¥15 HDS7 R
360 404 20 HDS7 R 360¥404¥20 HDS7 R
364 406 17 HDS7 D 364¥406¥17 HDS7 D
400 444 20 HDS7 R 400¥444¥20 HDS7 R
432 463 17 HDS7 R 432¥463¥17 HDS7 R
440 480 20 HDS7 R 440¥480¥20 HDS7 R
450 510 25 HDS7 R 450¥510¥25 HDS7 R
1) 12,7 mm adjustable spacer lugs (4)

seal width
d1 D b
mm – – –
461 495 20 HDS7 H 461¥495¥20 HDS7 H
470 530 25
530 28
HDS7
HDS7
R
R
470¥530¥25 HDS7 R
470¥530¥28 HDS7 R
2.8
500 550 20 HDS7 D 500¥550¥20 HDS7 D2)
515 555 20 HDS7 R 515¥555¥20 HDS7 R
520 570 22 HDS7 R 520¥570¥22 HDS7 R
530 580 20 HDS7 D 530¥580¥20 HDS7 D2)

580 22 HDS7 R 530¥580¥22 HDS7 R
542 578 16 HDS7 D 542¥578¥16 HDS7 D1)
560 604 20 HDS7 R 560¥604¥20 HDS7 R

610 20 HDS7 R 560¥610¥20 HDS7 R
610 22 HDS7 R 560¥610¥22 HDS7 R
620 29,34 HDS7 R 560¥620¥29 HDS7 R
590 630 20 HDS7 D 590¥630¥20 HDS7 D2)

640 20 HDS7 R 590¥640¥20 HDS7 R
610 660 25 HDS7 R 610¥660¥25 HDS7 R
640 690 25 HDS7 R 640¥690¥25 HDS7 R
647 700 25 HDS7 H 647¥700¥25 HDS7 H
720 784 23 HDS7 R 720¥784¥23 HDS7 R
760 810 25 HDS7 R 760¥810¥25 HDS7 R
1 250 1 314 21,54 HDS7 R 1250¥1314¥22 HDS7 R

Radial shaft seals – HDS7 – inch dimensions

d1 6.750 – 15.359 in.
on page 214.
d1 D

seal width
d1 D b
in./mm – – –
6.750 8.000 0.750 HDS7 R 597627

171,45 203,20 19,05
8.000 9.500 0.625 HDS7 H 596567

203,20 241,30 15,88
8.375 9.750 0.750 HDS7 R 596198

212,73 247,65 19,05
8.500 10.000 0.625 HDS7 R 596415

215,90 254,00 15,88
9.000 10.498 0.750 HDS7 R 596200

228,60 266,65 19,05
10.500 0.625 HDS7 R 597535
266,70 15,88
9.125 11.125 0.813 HDS7 R 597472

231,78 282,58 20,65
9.375 11.500 0.590 HDS7 R 597408

238,13 292,10 14,99
9.500 11.000 0.625 HDS7 H 596566

241,30 279,40 15,88
9.750 11.000 0.625 HDS7 R 596561

247,65 279,40 15,88
10.000 11.250 0.625 HDS7 R 1000129

254,00 285,75 15,88
10.500 12.000 0.688 HDS7 H 1050211

266,70 304,80 17,48
10.750 11.750 0.591 HDS7 R 1075020

273,05 298,45 15,01
12.750 0.625 HDS7 R 596171
323,85 15,88
12.750 0.813 HDS7 R 1075559
323,85 20,65

seal width
d1 D b
in./mm – – –
11.000 12.250 0.625 HDS7 R 1100120

279,40 311,15 15,88

13.000 0.813
330,20 20,65
HDS7 R 1100519 2.8
11.250 12.750 0.625 HDS7 H 1125219
285,75 323,85 15,88
11.500 13.000 0.688 HDS7 R 1150229

292,10 330,20 17,48
11.750 13.250 0.688 HDS7 R 1175219

298,45 336,55 17,48
12.000 13.500 0.625 HDS7 R 1213210

304,80 342,90 15,88
13.938 0.688 HDS7 R 1200500
354,03 17,48
14.000 0.813 HDS7 R 1200521
355,60 20,65
12.250 13.750 0.750 HDS7 D 1225259

311,15 349,25 19,05
14.000 0.688 HDS7 R 1225379
355,60 17,48
14.250 0.750 HDS7 R 1225549
361,95 19,05
14.250 0.813 HDS7 R 1225370
361,95 20,65
14.250 1.250 HDS7 R 1225589
361,95 31,75
12.500 14.000 0.688 HDS7 R 1250239

317,50 355,60 17,48
12.750 14.250 0.625 HDS7 H 1275219

323,85 361,95 15,88
13.000 15.000 1.000 HDS7 R 1300600

330,20 381,00 25,40
13.250 15.250 0.750 HDS7 R 1325569

336,55 387,35 19,05
13.500 15.500 0.813 HDS7 R 1350520

342,90 393,70 20,65
13.750 15.250 0.625 HDS7 H 1375719

349,25 387,35 15,88
13.875 16.000 1.000 HDS7 R 1387610

352,43 406,40 25,40
14.500 16.000 0.688 HDS7 R 1450220

368,30 406,40 17,48
14.750 16.500 0.688 HDS7 R 1475430

374,65 419,10 17,48
15.000 17.000 0.813 HDS7 R 1500510

381,00 431,80 20,65
15.250 17.250 0.625 HDS7 R 1525511

387,35 438,15 15,88
15.359 17.709 0.906 HDS7 R 1536691

390,12 449,81 23,01
Radial shaft seals – HDS7 – inch dimensions

d1 15.500 – 63.250 in.
on page 214.
d1 D

seal width
d1 D b
in./mm – – –
15.500 17.500 0.813 HDS7 R 1550559

393,70 444,50 20,65
15.750 17.250 0.750 HDS7 H 1575210

400,05 438,15 19,05
15.875 17.500 0.750 HDS7 H 1587330

403,23 444,50 19,05
16.000 17.500 0.625 HDS7 H 1600211

406,40 444,50 15,88
18.000 0.813 HDS7 H 1600519
457,20 20,65
16.250 17.750 0.688 HDS7 R 1625210

412,75 450,85 17,48
16.500 18.000 0.750 HDS7 R 1650280

419,10 457,20 19,05
17.000 18.500 0.625 HDS7 R 1700280

431,80 469,90 15,88
19.000 0.813 HDS7 R 1700579
482,60 20,65
17.375 18.875 0.750 HDS7 R 1737219

441,33 479,43 19,05
17.500 19.000 0.688 HDS7 H 1750220

444,50 482,60 17,48
19.000 0.688 HDS7 R 1750221
482,60 17,48
17.875 19.875 0.750 HDS7 R 1787540

454,03 504,83 19,05
19.000 20.500 0.750 HDS7 R 1900211

482,60 520,70 19,05
19.250 20.750 0.625 HDS7 R 596180

488,95 527,05 15,88

seal width
d1 D b
in./mm – – –
19.500 21.500 0.750 HDS7 R 1950211

495,30 546,10 19,05
20.000 21.500 0.750 HDS7 R 2000240

2.8
508,00 546,10 19,05
20.750 22.750 0.875 HDS7 D 2075569

527,05 577,85 22,23
21.260 23.228 0.984 HDS7 R 2126510

540,00 590,00 25,00
21.750 23.750 0.875 HDS7 R 2175569

552,45 603,25 22,23
22.250 24.250 0.875 HDS7 H 2225511

565,15 615,95 22,23
24.250 26.000 1.000 HDS7 H 2425419

615,95 660,40 25,40
25.000 26.500 0.750 HDS7 R 2500210

635,00 673,10 19,05
26.500 28.000 0.750 HDS7 R 2650240

673,10 711,20 19,05
27.000 29.000 0.875 HDS7 R 2700519

685,80 736,60 22,23
27.500 29.500 0.875 HDS7 R 2750510

698,50 749,30 22,23
27.875 29.815 0.875 HDS7 R 2788600

708,03 757,30 22,23
28.000 29.500 0.750 HDS7 R 2800240

711,20 749,30 19,05
30.000 0.875 HDS7 R 2800590
762,00 22,23
30.500 1.000 HDS7 H 2800650
774,70 25,40
28.500 30.500 0.875 HDS7 H 2850211

723,90 774,70 22,23
29.000 31.000 0.875 HDS7 R 2900579

736,60 787,40 22,23
30.500 32.500 0.875 HDS7 H 3050511

774,70 825,50 22,23
30.615 33.268 1.094 HDS7 R 3061721

777,62 845,01 27,79
31.496 33.465 0.984 HDS7 R 3149470

800,00 850,01 24,99
40.500 41.750 0.750 HDS7 H 4050061

1 028,70 1 060,45 19,05
47.000 49.000 0.875 HDS7 H 4700511

1 193,80 1 244,60 22,23
57.875 60.000 0.938 HDS7 R 5787611

1 470,03 1 524,00 23,83
63.250 64.500 1.188 HDS7 R 6325100

1 606,55 1 638,30 31,75
Radial shaft seals – HDS7K – metric dimensions

d1 200 – 810 mm
on page 214.
d1 D

seal width
d1 D b
mm – – –
200 230 15 HDS7K R 200¥230¥15 HDS7K R
230 260 15 HDS7K R 230¥260¥15 HDS7K R
280 310 15 HDS7K R 280¥310¥15 HDS7K R

320 18 HDS7K R 280¥320¥18 HDS7K R1)
320 20 HDS7K R 280¥320¥20 HDS7K R
310 350 20 HDS7K R 310¥350¥20 HDS7K R
320 360 25 HDS7K R 320¥360¥25 HDS7K R2)
360 404 20 HDS7K R 360¥404¥20 HDS7K R
400 450 18 HDS7K R 400¥450¥18 HDS7K R

450 22 HDS7K R 400¥450¥22 HDS7K R
446 496 22 HDS7K R 446¥496¥22 HDS7K R
450 500 18 HDS7K R 450¥500¥18 HDS7K R

500 22 HDS7K R 450¥500¥22 HDS7K R
485 535 22 HDS7K R 485¥535¥22 HDS7K R
520 570 18 HDS7K H 520¥570¥18 HDS7K H

570 18 HDS7K H 520¥570¥18 HDS7K H3)
530 580 22 HDS7K R 530¥580¥22 HDS7K R

580 20 HDS7K R 530¥580¥20 HDS7K R1)
540 590 18 HDS7K R 540¥590¥18 HDS7K R
560 610 20 HDS7K R 560¥610¥20 HDS7K R1)
1) 3,18 mm lugs (4)

2) 4,77 mm lugs (4)
3) 7,95 mm lugs (6)

seal width
d1 D b
mm – – –
570 610 18 HDS7K H 570¥610¥18 HDS7K H

610 18 HDS7K H 570¥610¥18 HDS7K H4)
620 22 HDS7K R 570¥620¥22 HDS7K R 2.9
760 824 25 HDS7K R 760¥824¥25 HDS7K R
810 874 25 HDS7K R 810¥874¥25 HDS7K R
4) 1,60 mm lugs (6)
Radial shaft seals – HDS7K – inch dimensions

d1 15.750 – 16.500 in.
on page 214.
d1 D

seal width
d1 D b
in./mm – – –
15.750 17.250 0.688 HDS7K R 1575241

400,05 438,15 17,48
16.000 18.000 0.807 HDS7K R 1600562

406,40 457,20 20,50
16.500 18.000 0.750 HDS7K R 1650248

419,10 457,20 19,05
2.9
Radial shaft seals – HDL – metric dimensions

d1 200 – 1 380 mm
a selection of available sizes.
b Contact your SKF sales
representative for more
information.
d1 D
Dimensions Designations
Shaft Bore Nominal Lip material
seal width
d1 D b R V
mm –
200 240 20 200¥240¥20 HDL R 200¥240¥20 HDL V
220 250 18 220¥250¥18 HDL R 220¥250¥18 HDL V
232 269,87 17,45 232¥270¥17 HDL R 232¥270¥17 HDL V
240 270 15 240¥270¥15 HDL R 240¥270¥15 HDL V

280 20 240¥280¥20 HDL R 240¥280¥20 HDL V
270 308 17,45 270¥308¥17 HDL R 270¥308¥17 HDL V
280 320 19,98 280¥320¥20 HDL R 280¥320¥20 HDL V

340 20,62 280¥340¥21 HDL R 280¥340¥21 HDL V
330 370 18 330¥370¥18 HDL R 330¥370¥18 HDL V
360 404 17,45 360¥404¥17 HDL R 360¥404¥17 HDL V
390 430 16 390¥430¥16 HDL R 390¥430¥16 HDL V
400 440 20 400¥440¥20 HDL R 400¥440¥20 HDL V

450 17,45 400¥450¥17 HDL R 400¥450¥17 HDL V

420 460 17,45 420¥460¥17 HDL R 420¥460¥17 HDL V
460 20 420¥460¥20 HDL R 420¥460¥20 HDL V
470 17,45 420¥470¥17 HDL R 420¥470¥17 HDL V
440 480 20 440¥480¥20 HDL R 440¥480¥20 HDL V
470 520 22 470¥520¥22 HDL R 470¥520¥22 HDL V
480 520 20 480¥520¥20 HDL R 480¥520¥20 HDL V
485 535 19 485¥535¥19 HDL R 485¥535¥19 HDL V
500 550 19 500¥550¥19 HDL R 500¥550¥19 HDL V
508 560 25 508¥560¥25 HDL R 508¥560¥25 HDL V
513 543 16 513¥543¥16 HDL R 513¥543¥16 HDL V
Dimensions Designation
seal width
d1 D b R V
mm –
520 560 18 520¥560¥18 HDL R 520¥560¥18 HDL V

570 22 520¥570¥22 HDL R 520¥570¥22 HDL V
530 580 20,62 530¥580¥21 HDL R 530¥580¥21 HDL V

2.10
540 590 24,98 540¥590¥25 HDL R 540¥590¥25 HDL V
560 610 20 560¥610¥20 HDL R 560¥610¥20 HDL V
565 601 20 565¥601¥20 HDL R 565¥601¥20 HDL V
600 640 20 600¥640¥20 HDL R 600¥640¥20 HDL V
630 670 20 630¥670¥20 HDL R 630¥670¥20 HDL V
640 680 20 640¥680¥20 HDL R 640¥680¥20 HDL V
650 714 25 650¥714¥25 HDL R 650¥714¥25 HDL V
668 706 25,40 668¥706¥25 HDL R 668¥706¥25 HDL V
750 814 25 750¥814¥25 HDL R 750¥814¥25 HDL V
760 804 18 760¥804¥18 HDL R 760¥804¥18 HDL V
780 844 25 780¥844¥25 HDL R 780¥844¥25 HDL V
790 854 25 790¥854¥25 HDL R 790¥854¥25 HDL V
837 889 22,22 837¥889¥22 HDL R 837¥889¥22 HDL V
838,10 881 20 838¥881¥20 HDL R 838¥881¥20 HDL V
840 904 25 840¥904¥25 HDL R 840¥904¥25 HDL V
920 958,01 19,05 920¥958¥19 HDL R 920¥958¥19 HDL V
930 980 22,22 930¥980¥22 HDL R 930¥980¥22 HDL V
990 1 040 25 990¥1040¥25 HDL R 990¥1040¥25 HDL V
1 000 1 050 22,22 1000¥1050¥22 HDL R 1000¥1050¥22 HDL V
1 055 1 100 25 1055¥1100¥25 HDL R 1055¥1100¥25 HDL V
1 105 1 160 22 1105¥1160¥22 HDL R 1105¥1160¥22 HDL V
1 350 1 414 22 1350¥1414¥22 HDL R 1350¥1414¥22 HDL V

1 415 25 1350¥1415¥25 HDL R 1350¥1415¥25 HDL V
1 380 1 440 25 1380¥1440¥25 HDL R 1380¥1440¥25 HDL V
Radial shaft seals – HDL – inch dimensions

d1 6.125 – 11.750 in.
information.
d1 D
seal width
d1 D b R V
in./mm –
6.125 7.625 0.687 HDL 1299 R HDL 1299 V

155,58 193,68 17,45
7.125 8.250 0.750 HDL 3011 R HDL 3011 V

180,98 209,55 19,05
7.875 9.375 0.687 HDL 9176 R HDL 9176 V

200,03 238,13 17,45
8.000 9.500 0.687 HDL 3921 R HDL 3921 V

203,20 241,30 17,45
8.125 10.125 0.687 HDL 9712 R HDL 9712 V

206,38 257,18 17,45
8.250 10.250 0.813 HDL 4499 R HDL 4499 V

209,55 260,35 20,65
8.375 9.875 0.687 HDL 3933 R HDL 3933 V

212,73 250,83 17,45
10.375 0.813 HDL 4500 R HDL 4500 V
263,53 20,65
8.500 9.750 0.562 HDL 1705 R HDL 1705 V

215,90 247,65 14,28
10.000 0.687 HDL 8453 R HDL 8453 V
254,00 17,45
8.625 10.125 0.687 HDL 3939 R HDL 3939 V

219,08 257,18 17,45
10.750 0.813 HDL 7718 R HDL 7718 V
273,05 20,65
8.750 10.250 0.687 HDL 3946 R HDL 3946 V

222,25 260,35 17,45
10.750 0.813 HDL 3952 R HDL 3952 V
273,05 20,65
8.875 10.875 0.813 HDL 3953 R HDL 3953 V

225,43 276,23 20,65
seal width
d1 D b R V
in./mm –
9.000 10.500 0.688 HDL 3954 R HDL 3954 V

228,60 266,70 17,45
9.125 10.625 0.687 HDL 3957 R HDL 3957 V

2.10
231,78 269,88 17,45
9.250 10.750 0.687 HDL 3963 R HDL 3963 V

234,95 273,05 17,45
9.375 11.375 0.813 HDL 4610 R HDL 4610 V

238,13 288,93 20,65
9.500 10.750 0.562 HDL 3145 R HDL 3145 V

241,30 273,05 14,28
11.500 0.813 HDL 3984 R HDL 3984 V
292,10 20,65
9.750 11.125 0.562 HDL 1692 R HDL 1692 V

247,65 282,58 14,28
11.750 0.687 HDL 9425 R HDL 9425 V
298,45 17,45
10.000 11.500 0.687 HDL 3992 R HDL 3992 V

254,00 292,10 17,45
12.000 0.813 HDL 3997 R HDL 3997 V
304,80 20,65
10.125 11.625 0.687 HDL 3999 R HDL 3999 V

257,18 295,28 17,45
10.250 11.750 0.687 HDL 4004 R HDL 4004 V

260,35 298,45 17,45
10.500 12.000 0.687 HDL 4011 R HDL 4011 V

266,70 304,80 17,45
10.750 12.250 0.687 HDL 4023 R HDL 4023 V

273,05 311,15 17,45
12.750 0.625 HDL 3014 R HDL 3014 V
323,85 15,88
10.875 12.375 0.687 HDL 4027 R HDL 4027 V

276,23 314,33 17,45
11.000 12.250 0.562 HDL 3135 R HDL 3135 V

279,40 311,15 14,28
13.000 0.688 HDL 6034 R HDL 6034 V
330,20 17,45
11.125 13.000 0.687 HDL 3699 R HDL 3699 V

282,58 330,20 17,45
11.250 12.750 0.687 HDL 4527 R HDL 4527 V

285,75 323,85 17,45
13.250 0.813 HDL 4047 R HDL 4047 V
336,55 20,65
11.375 13.375 0.813 HDL 4052 R HDL 4052 V

288,93 339,73 20,65
11.500 13.000 0.687 HDL 4057 R HDL 4057 V

292,10 330,20 17,45
11.750 13.250 0.687 HDL 4064 R HDL 4064 V

298,45 336,55 17,45

d1 12.000 – 15.125 in.
information.
d1 D
seal width
d1 D b R V
in./mm –
12.000 13.500 0.687 HDL 4612 R HDL 4612 V

304,80 342,90 17,45
13.750 0.687 HDL 3701 R HDL 3701 V
349,25 17,45
12.125 13.875 0.687 HDL 4053 R HDL 4053 V

307,98 352,43 17,45
12.250 13.750 0.687 HDL 4613 R HDL 4613 V

311,15 349,25 17,45
14.000 0.687 HDL 4055 R HDL 4055 V
355,60 17,45
12.375 13.875 0.687 HDL 4076 R HDL 4076 V

314,33 352,43 17,45
14.375 0.687 HDL 4097 R HDL 4097 V
365,13 17,45
12.500 14.000 0.687 HDL 4079 R HDL 4079 V

317,50 355,60 17,45
12.625 14.125 0.687 HDL 4081 R HDL 4081 V

320,68 358,78 17,45
12.687 14.750 0.813 HDL 9766 R HDL 9766 V

322,24 374,65 20,65
12.750 14.250 0.687 HDL 4089 R HDL 4089 V

323,85 361,95 17,45
15.000 0.813 HDL 4092 R HDL 4092 V
381,00 20,65
12.875 15.000 0.813 HDL 5404 R HDL 5404 V

327,03 381,00 20,65
13.000 14.500 0.687 HDL 4093 R HDL 4093 V

330,20 368,30 17,45
seal width
d1 D b R V
in./mm –
13.250 14.750 0.687 HDL 4101 R HDL 4101 V

336,55 374,65 17,45

15.000 0.687
381,00 17,45
HDL 7169 R HDL 7169 V 2.10
13.500 15.000 0.687 HDL 4121 R HDL 4121 V
342,90 381,00 17,45
15.750 0.813 HDL 4123 R HDL 4123 V
400,05 20,65
13.625 15.500 0.687 HDL 4120 R HDL 4120 V

346,08 393,70 17,45
13.750 15.250 0.687 HDL 4529 R HDL 4529 V

349,25 387,35 17,45
13.813 16.000 0.813 HDL 4108 R HDL 4108 V

350,85 406,40 20,65
13.875 16.000 0.813 HDL 4110 R HDL 4110 V

352,43 406,40 20,65
13.937 15.437 0.687 HDL 4130 R HDL 4130 V

354,00 392,10 17,45
15.500 0.687 HDL 4111 R HDL 4111 V
393,70 17,45
14.000 15.500 0.687 HDL 4131 R HDL 4131 V

355,60 393,70 17,45
15.750 0.750 HDL 4134 R HDL 4134 V
400,05 19,05
14.187 16.732 0.813 HDL 9280 R HDL 9280 V

360,34 424,99 20,65
14.250 15.750 0.687 HDL 4118 R HDL 4118 V

361,95 400,05 17,45
14.375 16.000 0.687 HDL 5481 R HDL 5481 V

365,13 406,40 17,45
14.500 16.000 0.687 HDL 4142 R HDL 4142 V

368,30 406,40 17,45
14.625 16.250 0.687 HDL 3856 R HDL 3856 V

371,48 412,75 17,45
14.750 16.250 0.687 HDL 4147 R HDL 4147 V

374,65 412,75 17,45
16.500 0.687 HDL 5990 R HDL 5990 V
419,10 17,45
14.875 16.500 0.687 HDL 3858 R HDL 3858 V

377,83 419,10 17,45
16.875 0.937 HDL 2622 R HDL 2622 V
428,63 23,80
14.906 17.000 0.813 HDL 3861 R HDL 3861 V

378,61 431,80 20,65
15.000 16.500 0.687 HDL 4151 R HDL 4151 V

381,00 419,10 17,45
15.125 16.750 0.687 HDL 4165 R HDL 4165 V

384,18 425,45 17,45

d1 15.250 – 19.250 in.
information.
d1 D
seal width
d1 D b R V
in./mm –
15.250 16.750 0.687 HDL 4615 R HDL 4615 V

387,35 425,45 17,45
17.250 0.875 HDL 3030 R HDL 3030 V
438,15 22,23
15.313 16.875 0.687 HDL 4158 R HDL 4158 V

388,95 428,63 17,45
15.359 17.717 0.687 HDL 4166 R HDL 4166 V

390,11 450,01 17,45
15.375 17.250 0.687 HDL 4167 R HDL 4167 V

390,53 438,15 17,45
15.500 17.496 0.813 HDL 4163 R HDL 4163 V

393,70 444,40 20,65
15.750 17.165 0.687 HDL 9986 R HDL 9986 V

400,05 436,00 17,45
17.312 0.687 HDL 9271 R HDL 9271 V
439,72 17,45
15.875 17.875 0.813 HDL 4176 R HDL 4176 V

403,23 454,03 20,65
16.000 17.500 0.687 HDL 4177 R HDL 4177 V

406,40 444,50 17,45
18.000 0.813 HDL 4180 R HDL 4180 V
457,20 20,65
16.250 17.750 0.687 HDL 4181 R HDL 4181 V

412,75 450,85 17,45
18.000 0.750 HDL 4184 R HDL 4184 V
457,20 19,05
16.375 17.875 0.687 HDL 4179 R HDL 4179 V

415,93 454,03 17,45
16.500 18.000 0.687 HDL 9863 R HDL 9863 V

419,10 457,20 17,45
18.500 0.813 HDL 4186 R HDL 4186 V
469,90 20,65
seal width
d1 D b R V
in./mm –
16.535 18.504 0.875 HDL 1929 R HDL 1929 V

419,98 470,00 22,23
16.750 18.250 0.687 HDL 3744 R HDL 3744 V

2.10
425,45 463,55 17,45
19.000 0.813 HDL 3748 R HDL 3748 V
482,60 20,65
16.937 19.291 0.813 HDL 9695 R HDL 9695 V

430,19 489,99 20,65
17.000 18.500 0.687 HDL 4188 R HDL 4188 V

431,80 469,90 17,45
19.250 0.813 HDL 4191 R HDL 4191 V
488,95 20,65
17.250 18.750 0.687 HDL 3751 R HDL 3751 V

438,15 476,25 17,45
17.500 19.000 0.687 HDL 4194 R HDL 4194 V

444,50 482,60 17,45
19.250 1.000 HDL 3005 R HDL 3005 V
488,95 25,40
17.625 19.250 0.687 HDL 4199 R HDL 4199 V

447,68 488,95 17,45
19.625 0.687 HDL 6850 R HDL 6850 V
498,48 17,45
17.750 19.750 0.813 HDL 4200 R HDL 4200 V

450,85 501,65 20,65
20.078 0.875 HDL 9084 R HDL 9084 V
509,98 22,23
17.875 19.875 0.813 HDL 4204 R HDL 4204 V

454,03 504,83 20,65
18.000 19.500 0.687 HDL 4206 R HDL 4206 V

457,20 495,30 17,45
19.750 0.687 HDL 5728 R HDL 5728 V
501,65 17,45
18.120 20.500 0.875 HDL 3754 R HDL 3754 V

460,25 520,70 22,23
18.125 20.500 0.875 HDL 3756 R HDL 3756 V

460,38 520,70 22,23
18.250 19.750 0.687 HDL 3757 R HDL 3757 V

463,55 501,65 17,45
18.375 19.875 0.687 HDL 4213 R HDL 4213 V

466,73 504,83 17,45
19.937 0.687 HDL 7103 R HDL 7103 V
506,39 17,45
18.500 20.000 0.687 HDL 3768 R HDL 3768 V

469,90 508,00 17,45
20.250 0.687 HDL 3772 R HDL 3772 V
514,35 17,45
19.000 20.500 0.750 HDL 4218 R HDL 4218 V

482,60 520,70 19,05
21.000 0.875 HDL 4219 R HDL 4219 V
533,40 22,23
19.250 20.750 0.750 HDL 4617 R HDL 4617 V

488,95 527,05 19,05

d1 19.375 – 23.375 in.
information.
d1 D
seal width
d1 D b R V
in./mm –
19.375 21.000 0.750 HDL 3778 R HDL 3778 V

492,13 533,40 19,05
19.500 21.000 0.750 HDL 3779 R HDL 3779 V

495,30 533,40 19,05
21.500 0.875 HDL 4221 R HDL 4221 V
546,10 22,23
19.750 21.750 0.875 HDL 4228 R HDL 4228 V

501,65 552,45 22,23
22.125 0.875 HDL 7400 R HDL 7400 V
561,98 22,23
19.875 22.000 0.875 HDL 3788 R HDL 3788 V

504,83 558,80 22,23
19.937 21.687 0.625 HDL 4233 R HDL 4233 V

506,40 550,84 15,88
21.500 0.750 HDL 3789 R HDL 3789 V
546,10 19,05
20.000 21.500 0.750 HDL 4235 R HDL 4235 V

508,00 546,10 19,05
20.143 22.250 0.875 HDL 3792 R HDL 3792 V

511,63 565,15 22,23
20.250 21.750 0.750 HDL 4239 R HDL 4239 V

514,35 552,45 19,05
22.250 0.875 HDL 4240 R HDL 4240 V
565,15 22,23
20.438 22.500 0.813 HDL 4242 R HDL 4242 V

519,13 571,50 20,65
20.500 22.000 0.750 HDL 4619 R HDL 4619 V

520,70 558,80 19,05
20.625 22.625 0.813 HDL 9893 R HDL 9893 V

523,88 574,68 20,65
seal width
d1 D b R V
in./mm –
20.750 22.750 0.875 HDL 4248 R HDL 4248 V

527,05 577,85 22,23
20.875 22.875 0.875 HDL 4250 R HDL 4250 V

2.10
530,23 581,03 22,23
21.000 22.500 0.750 HDL 5259 R HDL 5259 V

533,40 571,50 19,05
23.000 0.813 HDL 6535 R HDL 6535 V
584,20 20,65
21.250 23.000 0.750 HDL 4255 R HDL 4255 V

539,75 584,20 19,05
21.437 23.187 0.750 HDL 4256 R HDL 4256 V

544,49 588,94 19,05
21.500 23.250 0.750 HDL 4257 R HDL 4257 V

546,10 590,55 19,05
23.500 0.875 HDL 4259 R HDL 4259 V
596,90 22,23
21.625 23.375 0.750 HDL 4261 R HDL 4261 V

549,28 593,73 19,05
21.750 23.250 0.750 HDL 4621 R HDL 4621 V

552,45 590,55 19,05
24.750 0.875 HDL 4262 R HDL 4262 V
628,65 22,23
22.000 23.500 0.750 HDL 4269 R HDL 4269 V

558,80 596,90 19,05
24.250 0.813 HDL 9082 R HDL 9082 V
615,95 20,65
22.250 24.250 0.875 HDL 3764 R HDL 3764 V

565,15 615,95 22,23
22.375 24.250 0.750 HDL 4268 R HDL 4268 V

568,33 615,95 19,05
24.375 0.875 HDL 2576 R HDL 2576 V
619,13 22,23
22.437 24.000 0.750 HDL 4275 R HDL 4275 V

569,89 609,60 19,05
22.500 24.000 0.750 HDL 4271 R HDL 4271 V

571,50 609,60 19,05
24.500 0.875 HDL 4279 R HDL 4279 V
622,30 22,23
24.750 0.875 HDL 4273 R HDL 4273 V
628,65 22,23
22.750 24.750 0.875 HDL 4281 R HDL 4281 V

577,85 628,65 22,23
23.000 24.500 0.750 HDL 4283 R HDL 4283 V

584,20 622,30 19,05
24.750 0.750 HDL 5421 R HDL 5421 V
628,65 19,05
23.250 25.000 0.750 HDL 4286 R HDL 4286 V

590,55 635,00 19,05
25.250 0.750 HDL 9371 R HDL 9371 V
641,35 19,05
23.375 25.375 0.875 HDL 4287 R HDL 4287 V

593,73 644,53 22,23

d1 23.500 – 29.500 in.
information.
d1 D
seal width
d1 D b R V
in./mm –
23.500 24.681 0.591 HDL 3033 R HDL 3033 V

596,90 626,90 15,00
23.562 25.250 0.750 HDL 4290 R HDL 4290 V

598,47 641,35 19,05
25.375 0.750 HDL 4291 R HDL 4291 V
644,53 19,05
23.625 26.000 0.875 HDL 4292 R HDL 4292 V

600,08 660,40 22,23
23.750 25.250 1.000 HDL 6239 R HDL 6239 V

603,25 641,35 25,40
23.875 26.000 0.875 HDL 4293 R HDL 4293 V

606,43 660,40 22,23
24.000 25.500 0.750 HDL 4623 R HDL 4623 V

609,60 647,70 19,05
26.000 0.813 HDL 4295 R HDL 4295 V
660,40 20,65
24.250 26.250 0.875 HDL 4301 R HDL 4301 V

615,95 666,75 22,23
24.437 26.000 0.750 HDL 4302 R HDL 4302 V

620,69 660,40 19,05
26.935 1.000 HDL 9990 R HDL 9990 V
684,15 25,40
24.500 26.500 0.875 HDL 4305 R HDL 4305 V

622,30 673,10 22,23
25.000 26.500 0.750 HDL 4308 R HDL 4308 V

635,00 673,10 19,05
25.187 26.875 0.750 HDL 4311 R HDL 4311 V

639,74 682,63 19,05
25.250 27.250 0.750 HDL 4299 R HDL 4299 V

641,35 692,15 19,05
seal width
d1 D b R V
in./mm –
25.500 26.750 0.750 HDL 3022 R HDL 3022 V

647,70 679,45 19,05

27.500 0.875
698,50 22,23
HDL 4318 R HDL 4318 V 2.10
25.750 27.500 0.750 HDL 6998 R HDL 6998 V
654,05 698,50 19,05
25.875 28.000 0.875 HDL 4303 R HDL 4303 V

657,23 711,20 22,23
25.988 27.625 0.750 HDL 4306 R HDL 4306 V

660,09 701,68 19,05
26.000 27.625 0.750 HDL 5921 R HDL 5921 V

660,40 701,68 19,05
26.125 27.625 0.750 HDL 4329 R HDL 4329 V

663,58 701,68 19,05
26.375 28.188 0.875 HDL 4307 R HDL 4307 V

669,93 715,98 22,23
26.500 28.000 0.750 HDL 4533 R HDL 4533 V

673,10 711,20 19,05
27.000 29.000 0.875 HDL 4333 R HDL 4333 V

685,80 736,60 22,23
27.250 29.250 0.875 HDL 4626 R HDL 4626 V

692,15 742,95 22,23
27.500 29.000 0.750 HDL 4315 R HDL 4315 V

698,50 736,60 19,05
27.625 29.625 0.750 HDL 5001 R HDL 5001 V

701,68 752,48 19,05
27.875 29.813 0.875 HDL 4341 R HDL 4341 V

708,03 757,25 22,23
28.000 29.500 0.750 HDL 4343 R HDL 4343 V

711,20 749,30 19,05
29.813 0.750 HDL 4316 R HDL 4316 V
757,25 19,05
28.438 31.000 0.875 HDL 4321 R HDL 4321 V

722,33 787,40 22,23
28.500 30.500 0.875 HDL 4346 R HDL 4346 V

723,90 774,70 22,23
28.750 30.750 0.875 HDL 4628 R HDL 4628 V

730,25 781,05 22,23
29.000 30.500 0.750 HDL 4347 R HDL 4347 V

736,60 774,70 19,05
31.500 1.000 HDL 8793 R HDL 8793 V
800,10 25,40
29.500 31.500 0.875 HDL 4352 R HDL 4352 V

749,30 800,10 22,23
32.000 0.875 HDL 4538 R HDL 4538 V
812,80 22,23

d1 30.000 – 37.000 in.
information.
d1 D
seal width
d1 D b R V
in./mm –
30.000 31.500 0.750 HDL 4356 R HDL 4356 V

762,00 800,10 19,05
31.625 0.750 HDL 7870 R HDL 7870 V
803,28 19,05
32.500 0.875 HDL 4358 R HDL 4358 V
825,50 22,23
32.750 0.875 HDL 4359 R HDL 4359 V
831,85 22,23
30.250 32.500 0.875 HDL 4906 R HDL 4906 V

768,35 825,50 22,23
30.313 32.375 0.875 HDL 4361 R HDL 4361 V

769,95 822,33 22,23
30.500 32.500 0.875 HDL 4365 R HDL 4365 V

774,70 825,50 22,23
31.000 32.500 0.750 HDL 5739 R HDL 5739 V

787,40 825,50 19,05
33.500 0.875 HDL 4540 R HDL 4540 V
850,90 22,23
31.250 32.750 0.750 HDL 4631 R HDL 4631 V

793,75 831,85 19,05
31.750 33.750 0.875 HDL 5016 R HDL 5016 V

806,45 857,25 22,23
32.000 33.500 0.750 HDL 3023 R HDL 3023 V

812,80 850,90 19,05
32.125 34.125 0.875 HDL 4371 R HDL 4371 V

815,98 866,78 22,23
34.125 0.750 HDL 3002 R HDL 3002 V
866,78 19,05
32.313 34.500 0.875 HDL 4373 R HDL 4373 V

820,75 876,30 22,23
32.500 34.500 0.875 HDL 4377 R HDL 4377 V

825,50 876,30 22,22
seal width
d1 D b R V
in./mm –
32.750 34.250 0.750 HDL 4542 R HDL 4542 V

831,85 869,95 19,05
33.000 34.500 0.750 HDL 4381 R HDL 4381 V

2.10
838,20 876,30 19,05
34.650 0.787 HDL 4634 R HDL 4634 V
880,10 20,00
35.000 0.875 HDL 4382 R HDL 4382 V
889,00 22,23
33.500 35.000 0.875 HDL 9504 R HDL 9504 V

850,90 889,00 22,23
35.625 0.875 HDL 4548 R HDL 4548 V
904,88 22,23
33.625 35.625 0.875 HDL 4328 R HDL 4328 V

854,08 904,88 22,23
34.000 35.625 0.875 HDL 4331 R HDL 4331 V

863,60 904,88 22,23
34.250 36.000 0.750 HDL 3017 R HDL 3017 V

869,95 914,40 19,05
36.750 0.875 HDL 4335 R HDL 4335 V
933,45 22,23
34.500 36.000 0.750 HDL 6908 R HDL 6908 V

876,30 914,40 19,05
36.500 1.000 HDL 3021 R HDL 3021 V
927,10 25,40
34.750 36.750 0.875 HDL 3831 R HDL 3831 V

882,65 933,45 22,23
35.000 37.000 0.875 HDL 3835 R HDL 3835 V

889,00 939,80 22,23
35.250 37.250 0.875 HDL 4416 R HDL 4416 V

895,35 946,15 22,23
35.375 37.375 0.875 HDL 4417 R HDL 4417 V

898,53 949,33 22,23
35.437 38.583 0.875 HDL 9079 R HDL 9079 V

900,09 980,00 22,23
35.496 37.996 0.984 HDL 3001 R HDL 3001 V

901,60 965,10 25,00
35.500 37.500 0.875 HDL 4553 R HDL 4553 V

901,70 952,50 22,23
35.827 38.077 0.687 HDL 3003 R HDL 3003 V

910,00 967,15 17,45
36.000 38.000 0.875 HDL 4421 R HDL 4421 V

914,40 965,20 22,23
36.500 38.000 0.750 HDL 4429 R HDL 4429 V

927,10 965,20 19,05
36.750 38.750 0.875 HDL 4432 R HDL 4432 V

933,45 984,25 22,23
37.000 39.000 0.875 HDL 4434 R HDL 4434 V

939,80 990,60 22,23

d1 37.250 – 51.250 in.
information.
d1 D
seal width
d1 D b R V
in./mm –
37.250 39.250 0.875 HDL 4436 R HDL 4436 V

946,15 996,95 22,23
37.374 39.500 0.875 HDL 4425 R HDL 4425 V

949,30 1 003,30 22,23
37.437 39.500 0.875 HDL 3847 R HDL 3847 V

950,89 1 003,30 22,23
37.500 39.000 0.750 HDL 9411 R HDL 9411 V

952,50 990,60 19,05
38.000 39.500 0.750 HDL 3004 R HDL 3004 V

965,20 1 003,30 19,05
41.000 0.875 HDL 4340 R HDL 4340 V
1 041,40 22,23
38.250 40.250 0.875 HDL 4454 R HDL 4454 V

971,55 1 022,35 22,23
38.258 40.750 0.875 HDL 4342 R HDL 4342 V

971,75 1 035,05 22,23
38.500 41.000 0.875 HDL 4349 R HDL 4349 V

977,90 1 041,40 22,23
38.750 40.750 0.875 HDL 4456 R HDL 4456 V

984,25 1 035,05 22,23
38.937 41.000 0.875 HDL 4462 R HDL 4462 V

988,99 1 041,40 22,23
39.000 41.000 0.875 HDL 4465 R HDL 4465 V

990,60 1 041,40 22,23
42.250 0.875 HDL 4577 R HDL 4577 V
1 073,15 22,23
39.750 42.250 0.875 HDL 7538 R HDL 7538 V

1 009,65 1 073,15 22,23
40.000 42.000 0.875 HDL 4467 R HDL 4467 V

1 016,00 1 066,80 22,23
seal width
d1 D b R V
in./mm –
40.500 42.500 0.875 HDL 4468 R HDL 4468 V

1 028,70 1 079,50 22,23

43.020 0.875
1 092,70 22,23
HDL 1964 R HDL 1964 V 2.10
41.500 43.500 0.875 HDL 4635 R HDL 4635 V
1 054,10 1 104,90 22,23
41.875 43.500 1.000 HDL 8628 R HDL 8628 V

1 063,63 1 104,90 25,40
42.248 44.248 1.000 HDL 4470 R HDL 4470 V

1 073,10 1 123,90 25,40
42.500 44.250 0.875 HDL 5555 R HDL 5555 V

1 079,50 1 123,95 22,23
43.000 45.500 0.875 HDL 7189 R HDL 7189 V

1 092,20 1 155,70 22,23
43.500 45.500 0.875 HDL 4637 R HDL 4637 V

1 104,90 1 155,70 22,23
43.750 45.750 0.875 HDL 4638 R HDL 4638 V

1 111,25 1 162,05 22,23
44.000 46.000 0.875 HDL 7087 R HDL 7087 V

1 117,60 1 168,40 22,23
44.500 46.000 0.750 HDL 4563 R HDL 4563 V

1 130,30 1 168,40 19,05
46.004 47.500 0.750 HDL 3006 R HDL 3006 V

1 168,50 1 206,50 19,05
46.500 48.500 0.875 HDL 4578 R HDL 4578 V

1 181,10 1 231,90 22,23
46.850 48.819 0.875 HDL 8317 R HDL 8317 V

1 189,99 1 240,00 22,23
48.000 50.000 0.875 HDL 8579 R HDL 8579 V

1 219,20 1 270,00 22,23
48.250 50.250 0.875 HDL 4639 R HDL 4639 V

1 225,55 1 276,35 22,23
51.248 53.289 0.875 HDL 6747 R HDL 6747 V

1 301,71 1 353,55 22,23
51.250 53.300 0.875 HDL 1914 R HDL 1914 V

1 301,75 1 353,82 22,23
Radial shaft seals – HDS1, HDS2 and HDS3 – metric dimensions

d1 170 – 380 mm
on page 214.
d1 D

seal width
d1 D b
mm – – –
170 210 16 HDS1 R 170¥210¥16 HDS1 R
200 230 15,87 HDS1 R 200¥230¥16 HDS1 R

238 19 HDS1 V 200¥238¥19 HDS1 V
240 20 HDS2 R 200¥240¥20 HDS2 R
210 245 16 HDS1 R 210¥245¥16 HDS1 R

250 20 HDS1 V 210¥250¥20 HDS1 V
215 270 23 HDS2 R 215¥270¥23 HDS2 R
220 255 16 HDS1 R 220¥255¥16 HDS1 R1)

260 16 HDS1 R 220¥260¥16 HDS1 R
260 20 HDS1 R 220¥260¥20 HDS1 R
225 257 16 HDS1 R 225¥257¥16 HDS1 R
230 270 16 HDS2 V 230¥270¥16 HDS2 V
235 270 16 HDS2 R 235¥270¥16 HDS2 R
240 280 16 HDS2 R 240¥280¥16 HDS2 R

280 16 HDS2 D 240¥280¥16 HDS2 D
245 305 28 HDS2 R 245¥305¥28 HDS2 R
250 280 16 HDS2 R 250¥280¥16 HDS2 R

280 16 HDS1 D 250¥280¥16 HDS1 D
285 16 HDS2 D 250¥285¥16 HDS2 D
310 25 HDS1 R 250¥310¥25 HDS1 R
260 290 16 HDS2 D 260¥290¥16 HDS2 D

290 16 HDS2 V 260¥290¥16 HDS2 V
300 16 HDS2 R 260¥300¥16 HDS2 R
300 20 HDS2 D 260¥300¥20 HDS2 D
265 310 16 HDS1 R 265¥310¥16 HDS1 R

seal width
d1 D b
mm – – –
270 310 16 HDS3 V 270¥310¥16 HDS3 V2)

310 20 HDS2 V 270¥310¥20 HDS2 V
330 25 HDS2 V 270¥330¥25 HDS2 V 2.11
275 310 16 HDS1 R 275¥310¥16 HDS1 R
280 310 16 HDS1 R 280¥310¥16 HDS1 R

320 16 HDS1 R 280¥320¥16 HDS1 R
320 20 HDS1 R 280¥320¥20 HDS1 R
340 25 HDS1 R 280¥340¥25 HDS1 R
285 320 16 HDS2 R 285¥320¥16 HDS2 R

325 16 HDS1 R 285¥325¥16 HDS1 R
290 330 18 HDS2 R 290¥330¥18 HDS2 R

350 25 HDS2 R 290¥350¥25 HDS2 R
295 335 18 HDS1 R 295¥335¥18 HDS1 R
300 332 16 HDS2 R 300¥332¥16 HDS2 R

335 18 HDS2 R 300¥335¥18 HDS2 R
340 18 HDS1 V 300¥340¥18 HDS1 V
340 18 HDS1 D 300¥340¥18 HDS1 D
340 20 HDS1 V 300¥340¥20 HDS1 V
345 22 HDS1 R 300¥345¥22 HDS1 R
360 25 HDS2 V 300¥360¥25 HDS2 V
310 350 18 HDS2 V 310¥350¥18 HDS2 V

350 20 HDS2 D 310¥350¥20 HDS2 D
370 25 HDS2 D 310¥370¥25 HDS2 D
315 355 18 HDS1 V 315¥355¥18 HDS1 V
318 360 20 HDS2 R 318¥360¥20 HDS2 R
320 350 18 HDS1 R 320¥350¥18 HDS1 R

360 18 HDS1 R 320¥360¥18 HDS1 R
360 18 HDS2 V 320¥360¥18 HDS2 V
380 25 HDS1 R 320¥380¥25 HDS1 R
330 370 18 HDS1 R 330¥370¥18 HDS1 R

390 25 HDS1 R 330¥390¥25 HDS1 R
335 375 18 HDS3 D 335¥375¥18 HDS3 D2)
340 380 18 HDS2 V 340¥380¥18 HDS2 V

380 18 HDS2 D 340¥380¥18 HDS2 D
380 20 HDS2 H 340¥380¥20 HDS2 H
380 20 HDS2 R 340¥380¥20 HDS2 R
350 380 16 HDS2 R 350¥380¥16 HDS2 R

390 18 HDS2 D 350¥390¥18 HDS2 D
360 400 18 HDS1 R 360¥400¥18 HDS1 R

400 20 HDS1 V 360¥400¥20 HDS1 V
410 17 HDS1 R 360¥410¥17 HDS1 R
365 405 18 HDS2 R 365¥405¥18 HDS2 R
370 410 16 HDS2 R 370¥410¥16 HDS2 R
375 420 18 HDS2 R 375¥420¥18 HDS2 R
380 420 20 HDS2 R 380¥420¥20 HDS2 R

420 20 HDS2 V 380¥420¥20 HDS2 V
440 25 HDS2 R 380¥440¥25 HDS2 R

d1 390 – 700 mm
on page 214.
d1 D

seal width
d1 D b
mm – – –
390 430 16 HDS2 R 390¥430¥16 HDS2 R
395 430 18 HDS2 R 395¥430¥18 HDS2 R2)
400 440 20 HDS1 R 400¥440¥20 HDS1 R

440 20 HDS2 R 400¥440¥20 HDS2 R
460 25 HDS1 R 400¥460¥25 HDS1 R
410 450 20 HDS2 R 410¥450¥20 HDS2 R

460 22 HDS2 R 410¥460¥22 HDS2 R
420 460 20 HDS2 R 420¥460¥20 HDS2 R

470 22 HDS1 R 420¥470¥22 HDS1 R1)
430 480 22 HDS1 V 430¥480¥22 HDS1 V

480 25 HDS2 R 430¥480¥25 HDS2 R
435 485 18 HDS2 R 435¥485¥18 HDS2 R2)
440 470 20 HDS1 R 440¥470¥20 HDS1 R

480 20 HDS1 R 440¥480¥20 HDS1 R
445 485 20 HDS1 R 445¥485¥20 HDS1 R
450 490 20 HDS1 R 450¥490¥20 HDS1 R
448 480 16 HDS2 R 448¥480¥16 HDS2 R
460 500 20 HDS1 R 460¥500¥20 HDS1 R

500 20 HDS1 V 460¥500¥20 HDS1 V
510 22 HDS2 V 460¥510¥22 HDS2 V
520 25 HDS2 R 460¥520¥25 HDS2 R
470 510 20 HDS1 R 470¥510¥20 HDS1 R

530 26 HDS2 R 470¥530¥26 HDS2 R
480 520 20 HDS1 R 480¥520¥20 HDS1 R


seal width
d1 D b
mm – – –
485 535 22 HDS1 R 485¥535¥22 HDS1 R
490 530 20 HDS1 R 490¥530¥20 HDS1 R 2.11

500 540 20 HDS1 R 500¥540¥20 HDS1 R
550 18 HDS1 R 500¥550¥18 HDS1 R2)
505 555 20,62 HDS2 R 505¥555¥21 HDS2 R
510 554 20 HDS1 D 510¥554¥20 HDS1 D
515 555 20 HDS2 R 515¥555¥20 HDS2 R
520 560 20 HDS1 R 520¥560¥20 HDS1 R
525 575 20 HDS3 D 525¥575¥20 HDS3 D1)
530 580 20 HDS1 V 530¥580¥20 HDS1 V

580 22 HDS1 R 530¥580¥22 HDS1 R
535 580 20 HDS3 D 535¥580¥20 HDS3 D2)
540 590 20 HDS2 V 540¥590¥20 HDS2 V
545 595 22 HDS1 R 545¥595¥22 HDS1 R
550 590 20 HDS1 R 550¥590¥20 HDS1 R
560 610 20 HDS1 V 560¥610¥20 HDS1 V
570 620 22 HDS2 R 570¥620¥22 HDS2 R2)
580 620 20 HDS3 D 580¥620¥20 HDS3 D2)
585 620 20 HDS2 R 585¥620¥20 HDS2 R
590 630 20 HDS1 R 590¥630¥20 HDS1 R
600 640 20 HDS1 R 600¥640¥20 HDS1 R

650 22 HDS2 R 600¥650¥22 HDS2 R
650 25 HDS1 V 600¥650¥25 HDS1 V
610 660 20 HDS2 R 610¥660¥20 HDS2 R
630 670 20 HDS3 D 630¥670¥20 HDS3 D1)
640 690 25 HDS1 R 640¥690¥25 HDS1 R
650 700 22 HDS2 V 650¥700¥22 HDS2 V

710 25 HDS2 R 650¥710¥25 HDS2 R
660 700 18 HDS1 R 660¥700¥18 HDS1 R
670 714 20 HDS3 D 670¥714¥20 HDS3 D2)
680 730 20 HDS2 R 680¥730¥20 HDS2 R
685 720 20 HDS2 R 685¥720¥20 HDS2 R
690 730 20 HDS2 R 690¥730¥20 HDS2 R
695 770 30 HDS1 R 695¥770¥30 HDS1 R
700 740 20 HDS1 R 700¥740¥20 HDS1 R


d1 710 – 1 550 mm
on page 214.
d1 D

seal width
d1 D b
mm – – –
710 760 20 HDS1 V 710¥760¥20 HDS1 V
720 770 25 HDS2 R 720¥770¥25 HDS2 R
740 780 16,50 HDS1 R 740¥780¥17 HDS1 R
750 780 18 HDS1 R 750¥780¥18 HDS1 R

790 23 HDS1 V 750¥790¥23 HDS1 V
800 25 HDS2 R 750¥800¥25 HDS2 R
814 25 HDS1 R 750¥814¥25 HDS1 R2)
760 800 20 HDS1 V 760¥800¥20 HDS1 V

810 25 HDS1 R 760¥810¥25 HDS1 R
770 810 20 HDS1 V 770¥810¥20 HDS1 V

845 27,79 HDS1 R 770¥845¥28 HDS1 R
780 820 19,05 HDS2 R 780¥820¥19 HDS2 R
790 850 25 HDS1 V 790¥850¥25 HDS1 V
800 840 20 HDS1 R 800¥840¥20 HDS1 R
810 860 25 HDS2 R 810¥860¥25 HDS2 R
825 860 20 HDS2 R 825¥860¥20 HDS2 R
850 914 25 HDS1 R 850¥914¥25 HDS1 R
860 920 25 HDS1 R 860¥920¥25 HDS1 R
880 940 25 HDS2 R 880¥940¥25 HDS2 R2)

944 25 HDS3 D 880¥944¥25 HDS3 D2)
893 925 20 HDS2 H 893¥925¥20 HDS2 H
900 960 25 HDS1 R 900¥960¥25 HDS1 R2)

seal width
d1 D b
mm – – –
910 974 22 HDS1 R 910¥974¥22 HDS1 R2)
920 984 25 HDS2 V 920¥984¥25 HDS2 V 2.11

927 978 22 HDS2 D 927¥978¥22 HDS2 D
939 971 15,88 HDS3 H 939¥971¥16 HDS3 H2)
940 1 000 25 HDS1 R 940¥1000¥25 HDS1 R1)
950 1 006 20 HDS2 R 950¥1006¥20 HDS2 R
960 1 020 25 HDS2 H 960¥1020¥25 HDS2 H

1 040 23 HDS2 V 960¥1040¥23 HDS2 V
990 1 045 25 HDS1 R 990¥1045¥25 HDS1 R
1 000 1 035 20 HDS2 R 1000¥1035¥20 HDS2 R
1 020 1 084 25 HDS1 R 1020¥1084¥25 HDS1 R
1 055 1 100 25 HDS2 D 1055¥1100¥25 HDS2 D
1 105 1 160 25 HDS1 R 1105¥1160¥25 HDS1 R
1 120 1 184 25 HDS2 R 1120¥1184¥25 HDS2 R2)
1 140 1 180 20 HDS1 V 1140¥1180¥20 HDS1 V
1 220 1 255 20 HDS2 R 1220¥1255¥20 HDS2 R
1 250 1 314 25 HDS2 R 1250¥1314¥25 HDS2 R
1 260 1 300 18 HDS1 R 1260¥1300¥18 HDS1 R
1 370 1 420 19,05 HDS2 H 1370¥1420¥19 HDS2 H

1 420 20 HDS1 R 1370¥1420¥20 HDS1 R
1 530 1 580 20 HDS1 R 1530¥1580¥20 HDS1 R
1 550 1 610 25 HDS2 V 1550¥1610¥25 HDS2 V

Radial shaft seals – HDS1, HDS2 and HDS3 – inch dimensions

d1 6.000 – 9.750 in.
on page 214.
d1 D
Dimensions Design Lip Lug1) Designation

seal width
d1 D b
in./mm – – – –
6.000 7.500 0.625 HDS1 R 597623

152,40 190,50 15,88
6.750 7.750 0.625 HDS1 V 67512

171,45 196,85 15,88
7.250 8.750 0.625 HDS2 V 72510

184,15 222,25 15,88
7.500 8.750 0.625 HDS1 V 75048

190,50 222,25 15,88
7.750 9.000 0.625 HDS1 R 77531

196,85 228,60 15,88
9.250 0.625 HDS1 V 77539
234,95 15,88
8.000 9.250 0.625 HDS1 V 77996

203,20 234,95 15,88
9.500 0.687 HDS2 V 80009
241,30 17,45
10.000 1.000 HDS1 R 80088
254,00 25,40
8.125 9.378 0.625 HDS1 R 593198

206,38 238,20 15,88
10.125 1.000 HDS1 R 81253
257,18 25,40
8.250 9.500 0.625 HDS2 V 82526

209,55 241,30 15,88
10.250 0.625 HDS2 V 82559
260,35 15,88
8.345 10.750 1.250 HDS1 R 594186

211,96 273,05 31,75
8.375 9.750 0.625 HDS3 D 4 83702

212,73 247,65 15,88
1) Number of 0,5 in. adjustable spacer lugs

seal width
d1 D b
in./mm – – – –
8.500 9.750 0.625 HDS2 D 593768

215,90 247,65 15,88

10.500 0.625
266,70 15,88
HDS1 V 85018 2.11
8.540 9.750 0.625 HDS2 D 593855
215,90 247,65 15,88
8.625 10.500 0.750 HDS1 R 590758

219,08 266,70 19,05
10.625 0.750 HDS1 V 86240
269,88 19,05
8.750 10.000 0.625 HDS2 R 592626

222,25 254,00 15,88
8.875 10.125 0.625 HDS2 D 593779

225,43 257,18 15,88
9.000 10.250 0.750 HDS1 R 90017

228,60 260,35 19,05
10.500 0.625 HDS3 D 4 90027
266,70 15,88
11.000 0.750 HDS2 R 590787
279,40 19,05
9.125 10.375 0.625 HDS1 R 592653

231,78 263,53 15,88
10.625 0.688 HDS1 R 590270
269,88 17,48
11.125 0.688 HDS1 R 590174
282,58 17,48
11.125 0.813 HDS2 R 91202
282,50 20,65
9.250 10.750 0.750 HDS1 R 590093

234,95 273,05 19,05
11.250 0.813 HDS2 V 92544
285,75 20,65
11.250 1.000 HDS1 R 590798
285,75 25,40
9.375 11.375 0.875 HDS1 R 93751

238,13 288,93 22,23
9.438 10.635 0.750 HDS1 R 593894

239,73 270,13 19,05
9.500 10.750 0.625 HDS2 R 95045

241,30 273,05 15,88
11.000 0.625 HDS1 R 590653
279,40 15,88
11.500 0.813 HDS1 V 95068
292,10 20,65
11.500 1.000 HDS1 R 590820
292,10 25,40
9.688 10.875 0.625 HDS1 R 594080

246,08 276,23 15,88
9.750 11.000 0.625 HDS3 D 4 97527

247,65 279,40 15,88
11.750 1.000 HDS1 R 97548
298,45 25,40

d1 9.844 – 11.813 in.
on page 214.
d1 D

seal width
d1 D b
in./mm – – – –
9.844 11.409 0.625 HDS2 R 98444

250,04 289,79 15,88
9.875 11.375 0.750 HDS2 R 592763

250,83 288,93 19,05
11.500 0.750 HDS1 R 592727
292,10 19,05
9.938 12.000 1.000 HDS2 R 529752

252,43 304,80 25,40
10.000 11.250 0.625 HDS1 R 1000110

254,00 285,75 15,88
11.250 0.625 HDS2 R 1000111
285,75 15,88
11.500 0.625 HDS3 D 4 1000239
292,10 15,88
11.750 0.625 HDS1 R 1000360
298,45 15,88
10.125 11.625 0.688 HDS1 R 1013240

257,18 295,28 17,48
11.625 0.688 HDS2 R 1013242
295,28 17,48
10.236 12.590 0.984 HDS1 R 1024690

259,99 319,79 24,99
10.250 11.500 0.625 HDS2 D 1025112

260,35 292,10 15,88
11.750 0.688 HDS3 D 4 1025249
298,45 17,48
11.750 0.750 HDS2 R 1025252
298,45 19,05
10.375 11.625 0.875 HDS1 R 1038140

263,53 295,28 22,23

seal width
d1 D b
in./mm – – – –
10.438 12.438 0.875 HDS1 R 1044560

265,13 315,93 22,23
10.500 11.750 0.625 HDS1 V 1050113

2.11
266,70 298,45 15,88
12.000 0.625 HDS3 D 4 1050239
304,80 15,88
12.000 0.750 HDS2 V 1050251
304,80 19,05
10.688 12.500 0.625 HDS1 V 1068456

271,48 317,50 15,88
13.000 0.688 HDS2 V 1068693
330,20 17,48
10.750 12.000 0.625 HDS2 R 1075112

273,05 304,80 15,88
12.000 0.625 HDS1 R 1075110
304,80 15,88
12.250 0.625 HDS1 R 1075230
311,15 15,88
10.938 12.750 0.625 HDS1 R 1093440

277,83 323,85 15,88
11.000 12.250 0.625 HDS2 D 1100113

279,40 311,15 15,88
12.250 0.625 HDS2 V 1100104
311,15 15,88
12.500 0.750 HDS1 R 1100250
317,50 19,05
13.000 0.813 HDS2 R 1100553
330,20 20,65
11.250 12.500 0.625 HDS2 R 1125111

285,75 317,50 15,88
12.500 0.625 HDS1 R 1125110
317,50 15,88
11.375 13.000 0.750 HDS1 R 1138330

288,93 330,20 19,05
11.500 13.000 0.750 HDS2 R 1150253

292,10 330,20 19,05
13.500 0.813 HDS1 R 1150550
342,90 20,65
13.500 1.000 HDS1 R 1150580
342,90 25,40
11.688 12.938 0.625 HDS1 R 1169110

296,88 328,63 15,88
11.750 13.250 0.688 HDS2 V 1175224

298,45 336,55 17,48
13.250 0.750 HDS2 R 1175252
336,55 19,05
11.811 13.378 0.709 HDS1 R 1181300

300,00 339,80 18,01
11.813 13.812 0.875 HDS1 R 1181560

300,05 350,82 22,23

d1 12.000 – 15.250 in.
on page 214.
d1 D

seal width
d1 D b
in./mm – – – –
12.000 13.500 0.625 HDS2 R 1200231

304,80 342,90 15,88
13.500 0.625 HDS1 R 1200230
342,90 15,88
13.500 0.625 HDS3 D 4 1200239
342,90 15,88
13.500 0.688 HDS1 R 1200240
342,90 17,48
13.500 0.750 HDS2 R 1200255
342,90 19,05
14.000 0.625 HDS1 V 1200523
355,60 15,88
14.000 1.000 HDS2 R 1200585
355,60 25,40
12.250 13.750 0.625 HDS3 D 4 1225239

311,15 349,25 15,88
12.500 13.750 0.625 HDS1 R 1250110

317,50 349,25 15,88
14.000 0.688 HDS3 D 4 1250249
355,60 17,48
14.500 0.750 HDS1 R 1250540
368,30 19,05
14.500 0.813 HDS2 V 1250554
368,30 20,65
12.750 14.250 0.688 HDS2 V 1275243

323,85 361,95 17,48
14.250 0.750 HDS2 R 1275252
361,95 19,05
13.000 14.500 0.688 HDS2 R 1300244

330,20 368,30 17,48
14.500 0.688 HDS2 V 1300283
368,30 17,48
15.000 0.750 HDS2 R 1300542
381,00 19,05

seal width
d1 D b
in./mm – – – –
13.250 14.750 0.625 HDS3 D 4 1325239

336,55 374,65 15,88

14.750 0.688
374,65 17,48
HDS2 R 1325242 2.11
13.500 15.250 0.750 HDS1 R 1350380
342,90 387,35 19,05
15.500 0.813 HDS2 V 1350564
393,70 20,65
13.750 15.000 0.750 HDS1 R 1375130

349,25 381,00 19,05
15.250 0.625 HDS1 R 1375230
387,35 15,88
15.250 0.688 HDS1 R 1375240
387,35 17,48
15.500 0.750 HDS1 R 1375380
393,70 19,05
15.750 0.813 HDS2 V 1375553
400,05 20,65
14.000 15.500 0.625 HDS2 V 1400234

355,60 393,70 15,88
15.500 0.625 HDS2 R 1400232
393,70 15,88
15.500 0.750 HDS1 R 1400250
393,70 19,05
15.750 0.688 HDS1 R 1400370
400,05 17,48
16.000 1.000 HDS1 R 1400580
406,40 25,40
14.250 15.750 0.750 HDS2 R 1425252

361,95 400,05 19,05
16.250 0.813 HDS2 R 1425552
412,75 20,65
14.375 16.000 0.688 HDS2 D 1438321

365,13 406,40 17,48
14.500 16.000 0.688 HDS2 R 1450242

368,30 406,40 17,48
16.500 0.750 HDS2 R 1450542
419,10 19,05
14.750 16.500 0.875 HDS2 R 1475411

374,65 419,10 22,23
15.000 16.500 0.688 HDS1 R 1500240

381,00 419,10 17,48
16.500 0.750 HDS1 R 1500250
419,10 19,05
16.750 0.750 HDS1 R 1500380
425,45 19,05
17.000 0.750 HDS3 D 4 1500549
431,80 19,05
15.250 16.750 0.750 HDS2 R 1525252

387,35 425,45 19,05
17.250 0.750 HDS2 R 1525542
438,15 19,05
17.250 0.875 HDS1 R 1525560
438,15 22,23

d1 15.500 – 22.250 in.
on page 214.
d1 D

seal width
d1 D b
in./mm – – – –
15.500 16.875 0.625 HDS1 R 1550160

393,70 428,63 15,88
17.500 0.750 HDS2 R 1550542
444,50 19,05
17.500 0.813 HDS1 R 1550550
444,50 20,65
15.625 17.625 0.875 HDS1 R 1563560

396,88 447,68 22,23
15.750 17.250 0.688 HDS3 D 4 1575249

400,05 438,15 17,48
16.000 17.500 0.750 HDS1 R 1600250

406,40 444,50 19,05
18.000 1.000 HDS2 R 1600585
457,20 25,40
16.250 17.750 0.688 HDS1 R 1625240

412,75 450,85 17,48
16.500 18.000 0.750 HDS2 R 1650252

419,10 457,20 19,05
16.750 18.500 0.875 HDS1 V 1675413

425,45 469,90 22,23
17.000 18.500 0.688 HDS2 R 1700245

431,80 469,90 17,48
18.500 0.750 HDS2 D 1700251
469,90 19,05
19.000 0.750 HDS2 R 1700541
482,60 19,05
17.250 18.750 0.750 HDS2 R 1725255

438,15 476,25 19,05

seal width
d1 D b
in./mm – – – –
17.500 19.000 0.625 HDS1 R 1750230

444,50 482,60 15,88

19.250 0.688
488,95 17,48
HDS1 R 1750370 2.11
19.500 0.688 HDS1 R 1750530
495,30 17,48
17.625 19.250 0.688 HDS1 R 1763320

447,68 488,95 17,48
18.000 19.500 0.688 HDS3 D 4 1800249

457,20 495,30 17,48
19.750 0.750 HDS2 R 1800382
501,65 19,05
18.250 19.750 0.750 HDS2 R 1825252

463,55 501,65 19,05
18.500 20.500 0.875 HDS1 R 1850560

469,90 520,70 22,23
18.750 20.750 0.813 HDS2 R 1875553

476,25 527,05 20,65
19.000 20.500 0.750 HDS1 R 1900250

482,60 520,70 19,05
21.000 0.875 HDS2 V 1900562
533,40 22,23
19.250 21.250 0.938 HDS1 R 1925570

488,95 539,75 23,24
19.500 21.500 0.875 HDS1 R 1950560

495,30 546,10 22,23
20.000 21.500 0.625 HDS3 D 4 2000239

508,00 546,10 15,88
20.250 21.750 0.750 HDS1 R 2025250

514,35 552,45 19,05
20.500 22.500 0.750 HDS2 R 2050542

520,70 571,50 19,05
22.500 0.875 HDS1 R 2050560
571,50 22,23
20.750 22.750 0.875 HDS2 D 2075562

527,05 577,85 22,23
21.000 22.750 0.813 HDS1 R 2100390

533,40 577,85 20,65
23.000 0.625 HDS3 D 4 2100529
584,20 15,87
21.500 23.500 0.813 HDS1 R 2150550

546,10 596,90 20,65
22.000 23.500 0.750 HDS2 V 2200213

558,80 596,90 19,05
24.000 0.875 HDS2 R 2200565
609,60 22,23
24.000 1.250 HDS1 D 526339
609,60 31,75
22.250 24.250 0.875 HDS3 H 4 2225568

565,15 615,95 22,23

d1 23.000 – 63.340 in.
on page 214.
d1 D

seal width
d1 D b
in./mm – – – –
23.000 24.750 0.750 HDS2 V 2300384

584,20 628,65 19,05
23.500 25.500 0.875 HDS1 R 2350560

596,90 647,70 22,23
24.000 25.500 0.750 HDS1 R 2400250

609,60 647,70 19,05
26.000 0.875 HDS2 R 2400559
660,40 22,23
24.250 26.250 0.875 HDS2 V 2425562

615,95 666,75 22,23
25.000 27.000 1.000 HDS1 R 2500580

635,00 685,80 25,40
25.500 27.500 1.000 HDS2 R 2550585

647,70 698,50 25,40
26.000 27.625 0.750 HDS2 R 2600332

660,40 701,68 19,05
28.500 0.875 HDS1 R 2600760
723,90 22,23
26.500 28.500 0.875 HDS1 R 2650560

673,10 723,90 22,23
28.000 29.625 0.750 HDS2 R 2800331

711,20 752,48 19,05
30.000 0.875 HDS2 R 2800565
762,00 22,23
29.000 31.000 0.875 HDS2 R 2900563

736,60 787,40 22,23
29.500 31.500 0.875 HDS2 D 2950564

749,30 800,10 22,23

seal width
d1 D b
in./mm – – – –
30.250 32.500 0.875 HDS1 R 3025660

768,35 825,50 22,23
30.500 32.500 0.875 HDS2 V 3050514

2.11
774,70 825,50 22,23
33.000 1.000 HDS2 R 3050785
838,20 25,40
31.000 33.000 0.813 HDS1 R 3100550

787,40 838,20 20,65
32.500 34.500 0.875 HDS1 R 3250560

825,50 876,30 22,23
33.000 34.688 0.750 HDS2 R 3300351

838,20 881,08 19,05
33.500 36.000 0.875 HDS1 R 3350760

850,90 914,40 22,23
34.000 36.000 0.875 HDS1 R 3400560

863,60 914,40 22,23
34.500 36.500 0.875 HDS2 D 3450563

876,30 927,10 22,23
37.500 39.000 0.875 HDS2 R 3750272

952,50 990,60 22,23
39.500 0.875 HDS1 D 3750561
1 003,30 22,23
38.000 40.000 0.875 HDS2 R 3800565

965,20 1 016,00 22,23
40.500 43.000 0.875 HDS2 V 4050774

1 028,70 1 092,20 22,23
43.500 45.500 0.875 HDS2 R 4350565

1 104,90 1 155,70 22,23
45.500 0.875 HDS1 R 4350560
1 155,70 22,23
45.000 47.000 0.875 HDS1 R 4500560

1 143,00 1 193,80 22,23
46.000 47.500 0.750 HDS2 H 4600252

1 168,40 1 206,50 19,05
49.000 50.625 0.813 HDS1 R 4900340

1 244,60 1 285,88 20,65
51.500 53.500 1.500 HDS1 R 5150590

1 308,10 1 358,90 38,10
54.750 56.375 0.875 HDS1 R 5475340

1 390,65 1 431,93 22,23
62.500 64.000 0.875 HDS1 R 6250270

1 587,50 1 625,60 22,23
63.340 64.500 0.750 HDS2 D 6334342

1 608,84 1 638,30 19,05

d1 7.939 in.
on page 214.
d1 D
Dimensions Design Lip material Designation

Shaft Bore Nominal
seal width
d1 D b
in./mm – – –
7.939 10.125 0.688 HDS1K H 597606

201,65 257,18 17,48
2.12
Radial shaft seals – HDS2K – metric dimensions

d1 340 – 810 mm
on page 214.
d1 D

Shaft Bore Nominal
seal width
d1 D b
mm – – –
340 380 18 HDS2K V 340¥380¥18 HDS2K V
360 404 20 HDS2K R 360¥404¥20 HDS2K R
400 450 18 HDS2K R 400¥450¥18 HDS2K R
810 874 25 HDS2K R 810¥874¥25 HDS2K R

d1 16.500 in.
on page 214.
d1 D
2.13

Shaft Bore Nominal
seal width
d1 D b
in./mm – – –
16.500 18,000 0.750 HDS2K R 1650230

419,10 457,20 19,05
Radial shaft seals – HDSF and HDSH seals – metric dimensions

d1 440 – 760 mm
on page 214.
d1 D

Shaft Bore Nominal
seal width
d1 D b
mm – – –
440 490 20,40 HDSF2 VT 440¥490¥20 HDSF2 VT

490 20,40 HDSH7 HT 440¥490¥20 HDSH7 HT
500 540 20 HDSF2 RT 500¥540¥20 HDSF2 RT
760 800 20 HDSF2 HT 760¥800¥20 HDSF2 HT

800 20 HDSF7 HT 760¥800¥20 HDSF7 HT
Radial shaft seals – HDSF and HDSH seals – inch dimensions

d1 10.500 – 31.890 in.
on page 214.
d1 D
2.14

Shaft Bore Nominal
seal width
d1 D b
in./mm – – –
10.500 12.500 1.000 HDSF1 VT 1050966

266,70 317,50 25,40
14.000 16.000 1.000 HDSF1 VT 1400957

355,60 406,40 25,40
15.500 17.500 0.750 HDSH7 RT 1550951

393,70 444,50 19,05
17.500 0.750 HDSF2 HT 1550952
444,50 19,05
16.000 18.000 0.875 HDSF2 HT 1600510

406,40 457,20 22,23
18.500 20.500 0.875 HDSF2 DT 1850953

469,90 520,70 22,23
19.000 21.000 0.870 HDSF2 VT 1900954

482,60 533,40 22,10
31.890 34.409 0.921 HDSF2 VT 3189981

810,01 873,99 23,39
34.409 0.921 HDSH7 HT 3189988
873,99 23,39
Radial shaft seals – HDSA and HDSB seals – metric dimensions

d1 240 – 790 mm
on page 214.
d1 D

Shaft Bore Nominal
seal width
d1 D b
mm – – –
240 280 23 HDSA1 RD 240¥280¥23 HDSA1 RD
270 330 25,40 HDSA1 RD 270¥330¥25 HDSA1 RD
310 370 25,40 HDSA1 RD 310¥370¥25 HDSA1 RD
317 352 23 HDSA1 RD 317¥352¥23 HDSA1 RD
320 360 25 HDSB2 RD 320¥360¥25 HDSB2 RD

380 28 HDSA2 RD 320¥360¥28 HDSA2 RD
364 420 25 HDSA2 RD 364¥420¥25 HDSA2 RD
380 420 22,20 HDSA2 VD 380¥420¥22 HDSA2 VD

440 28 HDSA2 RD 380¥440¥28 HDSA2 RD
390 434 22 HDSA2 VD 390¥434¥22 HDSA2 VD
400 460 28 HDSA2 RD 400¥460¥28 HDSA2 RD
430 470 20 HDSB1 RD 430¥470¥20 HDSB1 RD
440 480 22,23 HDSA2 VD 440¥480¥22 HDSA2 VD
560 620 30 HDSA2 RD 560¥620¥30 HDSA2 RD
580 640 30 HDSA2 RD 580¥640¥30 HDSA2 RD

640 30 HDSB1 RD 580¥640¥30 HDSB1 RD
790 850 25 HDSA1 RD 790¥850¥25 HDSA1 RD
Radial shaft seals – HDSA and HDSB seals – inch dimensions

d1 6.000 – 9.620 in.
on page 214.
d1 D
2.15
Dimensions Design Lip Designation Dimensions Design Lip Designation

Shaft Bore Nominal material Shaft Bore Nominal material
d1 D b d1 D b
in./mm – – – in./mm – – –
6.000 7.500 0.750 HDSA1 RD 597625 8.750 10.750 0.875 HDSA1 RD 592492
152,40 190,50 19,05 222,25 273,05 22,23
6.625 8.125 0.875 HDSA2 VD 594828 8.875 10.125 0.875 HDSA2 DD 595127
168,28 206,38 22,23 225,43 257,18 22,23
10.875 0.875 HDSA1 RD 591984
7.250 8.750 0.875 HDSA2 VD 72594 276,23 22,23
184,15 222,25 22,23 11.250 0.875 HDSA1 RD 592464
285,75 22,23
8.000 10.000 1.000 HDSB1 RD 592328
203,20 254,00 25,40 9.000 10.250 0.875 HDSA2 VD 90054
10.000 1.250 HDSA1 RD 592336 228,60 260,35 22,23
254,00 31,75 10.500 0.875 HDSA1 RD 597343
10.125 1.250 HDSB1 RD 80092 266,70 22,23
257,18 31,75 11.000 1.000 HDSA2 VD 594903
279,40 25,40
8.250 10.250 0.875 HDSB1 RD 591921
209,55 260,35 22,23 9.250 10.438 0.875 HDSA1 RD 92591
10.250 1.250 HDSB1 RD 590357 234,95 265,13 22,23
260,35 31,75 11.000 1.375 HDSA1 RD 592452
279,40 34,93
8.500 9.750 0.870 HDSA2 DD 595513 11.250 0.875 HDSA1 VD 593312
215,90 247,65 22,10 285,75 22,23
10.000 0.875 HDSA1 VD 596196
254,00 22,23 9.375 12.750 1.250 HDSB1 RD 590688
10.000 1.000 HDSA1 RD 590731 238,13 323,85 31,75
254,00 25,40
10.500 0.875 HDSA1 VD 592798 9.500 11.500 1.250 HDSA2 RD 590375
266,70 22,23 241,30 292,10 31,75
10.500 1.000 HDSB1 RD 592149 11.500 1.250 HDSA2 DD 593667
266,70 25,40 292,10 31,75
10.500 1.000 HDSA2 VD 594902
266,70 25,40 9.620 12.750 1.250 HDSA1 RD 96290
10.500 1.250 HDSA1 RD 590245 244,35 323,85 31,75
266,70 31,75

d1 9.750 – 15.750 in.
on page 214.
d1 D

d1 D b d1 D b
in./mm – – – in./mm – – –
9.750 11.000 0.875 HDSA1 RD 593053 10.500 12.500 1.000 HDSA1 RD 1050956
247,65 279,40 22,23 266,70 317,50 25,40
11.000 1.000 HDSA1 DD 593428 12.500 1.000 HDSB1 RD 1050958
279,40 25,40 317,50 25,40
11.125 0.875 HDSA2 DD 594974 12.500 1.000 HDSA1 VT 1050966
282,58 22,23 317,50 25,40
11.250 0.875 HDSA2 DD 595514
285,75 22,23 10.625 12.500 0.969 HDSA1 RD 1062945
11.750 1.000 HDSA1 DD 595568 269,88 317,50 24,61
298,45 25,40 13.000 1.000 HDSB1 RD 1063971
330,20 25,40
9.875 11.875 1.000 HDSA2 RD 592847
250,83 301,63 25,40 10.688 12.500 1.000 HDSA1 RD 1068940
271,48 317,50 25,40
10.000 11.250 0.875 HDSA1 RD 1000910
254,00 285,75 22,23 10.750 12.500 0.875 HDSA2 RD 1075942
11.250 0.875 HDSA2 VD 1000914 273,05 317,50 22,23
285,75 22,23 13.371 1.250 HDSB1 RD 107591
11.500 1.250 HDSA1 RD 1000920 339,62 31,75
292,10 31,75
12.000 0.875 HDSA1 RD 1000950 11.000 12.500 1.250 HDSA1 RD 1100918
304,80 22,23 279,40 317,50 31,75
12.000 1.250 HDSA1 RD 1000952 13.000 0.875 HDSA1 RD 1100950
304,80 31,75 330,20 22,23
12.000 1.250 HDSB1 RD 1000953 13.000 1.000 HDSA1 RD 1100951
304,80 31,75 330,20 25,40
12.000 1.500 HDSA1 RD 1000954 13.000 1.250 HDSA1 RD 1100952
304,80 38,10 330,20 31,75
12.500 1.000 HDSA1 RD 1000971 13.000 1.250 HDSB1 RD 1100953
317,50 25,40 330,20 31,75
13.500 1.250 HDSA1 RD 1100971
10.375 11.625 0.875 HDSA2 DD 1037912 342,90 31,75
263,53 295,28 22,23
11.417 12.994 0.875 HDSA1 VD 1141937
290,00 330,00 22,23
13.000 0.875 HDSA2 VD 1141273
330,20 22,23

d1 D b d1 D b
in./mm – – – in./mm – – –
11.500 13.000 0.750 HDSA1 RD 115025 13.386 15.000 0.875 HDSA2 VD 1338273
292,10 330,20 19,05 340,00 381,00 22,23

13.000 0.875 HDSA1 DD
330,20 22,23
1150925
13.500 15.500 0.875 HDSA2 RD 1350954
2.15
13.000 1.063 HDSA1 RD 1150920 342,90 393,70 22,23
330,20 27,00 15.500 1.250 HDSB1 RD 1350970
393,70 31,75
11.750 13.250 0.875 HDSA2 VD 1175924 15.500 1.250 HDSB1 VD 593517
298,45 336,55 22,23 393,70 31,75
13.250 0.875 HDSA2 RD 527709
336,55 22,23 13.750 15.500 0.875 HDSA1 VD 1375418
13.750 1.250 HDSB1 RD 1175952 349,25 393,70 22,23
349,25 31,75
13.875 15.125 0.875 HDSA2 RD 1387912
12.000 13.500 0.875 HDSA1 RD 1200920 352,43 384,18 22,23
304,80 342,90 22,23
14.000 0.844 HDSA2 VD 1200962 13.938 15.744 1.250 HDSA2 RD 1394942
355,60 21,44 354,03 399,90 31,75
14.000 1.000 HDSB1 RD 1200958
355,60 25,40 14.000 15.500 1.000 HDSA1 RD 1400925
14.000 1.250 HDSB1 RD 1200952 355,60 393,90 25,40
355,60 31,75 16.000 1.000 HDSA1 VT 1400957
406,40 25,40
12.250 14.250 1.250 HDSA2 RD 1225588 16.000 1.375 HDSA1 RD 1400950
311,15 361,95 20,65 406,40 34,93
14.250 1.250 HDSA1 RD 1225960 16.250 1.000 HDSA2 RD 1400965
361,95 31,75 412,75 25,40
16.250 1.000 HDSA2 VD 528307
12.500 13.750 0.906 HDSA2 RD 1250912 412,75 25,40
317,50 349,25 23,00 16.750 0.968 HDSB2 RD 1400981
14.000 0.875 HDSA2 DD 1250272 425,45 24,59
356,60 22,23
14.000 0.875 HDSA2 DD 1250922 14.250 15.750 1.000 HDSA1 RD 1425920
355,60 22,23 361,95 400,05 25,40
14.500 1.250 HDSA1 RD 1250950 16.250 1.000 HDSB1 RD 1425950
368,30 31,75 412,75 25,40
12.750 14.750 1.250 HDSB1 RD 1275950 14.400 15.587 0.875 HDSB1 RD 1440901
323,85 374,65 31,75 365,76 395,91 22,23
12.875 14.125 0.875 HDSA2 RD 1287912 15.000 17.000 0.875 HDSA1 RD 1500951
327,03 358,78 22,23 381,00 431,80 22,23
17.000 1.250 HDSA1 RD 1500950
13.000 14.500 0.875 HDSA1 RD 1300900 431,80 31,75
330,20 368,30 22,23 17.500 1.000 HDSA1 RD 1500973
14.500 0.875 HDSB1 RD 1300929 444,50 25,40
368,30 22,23
14.500 1.000 HDSA1 RD 1300920 15.125 16.375 0.875 HDSA2 RD 1512912
368,30 25,40 384,18 415,93 22,23
13.250 14.750 0.906 HDSA2 DD 1325922 15.313 17.313 0.813 HDSA2 RD 592865
336,55 374,65 23,00 388,95 439,75 20,65
14.750 0.906 HDSA2 VD 1325928 17.313 0.875 HDSA1 RD 1531950
374,65 23,00 439,75 22,23
14.875 1.000 HDSA2 DD 1325932
377,83 25,40 15.375 16.625 0.875 HDSA2 RD 1537142
15.000 1.250 HDSA1 RD 1325940 390,53 422,28 22,23
381,00 31,75
15.250 1.000 HDSA1 RD 1325950 15.750 17.750 1.250 HDSA1 RD 1575910
387,35 25,40 400,05 450,85 31,75

d1 16.000 – 46.840 in.
on page 214.
d1 D

d1 D b d1 D b
in./mm – – – in./mm – – –
16.000 18.000 0.875 HDSA1 RD 1600951 19.500 21.500 1.250 HDSA1 RD 1950950
406,40 457,20 22,23 495,30 546,10 31,75
18.000 1.000 HDSA2 RD 1600955
457,20 25,40 19.750 22.125 1.000 HDSA1 RD 1975972
18.000 1.125 HDSB1 RD 1600940 501,65 561,98 25,40
457,20 28,58
18.000 1.125 HDSA1 RD 1600941 20.000 21.250 1.375 HDSA1 RD 2000913
457,20 28,58 508,00 539,75 34,93
21.500 0.875 HDSA1 VD 593789
16.375 17.562 1.000 HDSA1 RD 1637901 546,10 22,23
415,93 446,07 25,40
20.438 22.500 1.000 HDSA1 RD 2044580
17.000 18.250 0.875 HDSA2 RD 1700142 519,13 571,50 25,40
431,80 463,55 22,23
19.000 1.250 HDSA1 RD 1700950 20.500 22.000 1.500 HDSA2 RD 2050282
482,60 31,75 520,70 558,80 38,10
22.500 0.875 HDSA2 VD 2050954
17.500 19.000 1.250 HDSA1 RD 1750920 571,50 22,23
444,50 482,60 31,75
19.500 1.000 HDSA2 RD 1750958 20.750 22.750 1.250 HDSA1 RD 2075950
495,30 25,40 527,05 577,85 31,75
19.500 1.250 HDSA1 RD 1750952
495,30 31,75 21.000 22.250 1.375 HDSA1 RD 2100913
533,40 565,15 34,93
18.000 20.000 1.500 HDSA1 RD 1800950
457,20 508,00 38,10 21.250 23.000 0.875 HDSA1 RD 2125940
20.250 1.000 HDSA2 RD 1800965 539,75 584,20 22,23
514,35 25,40
20.250 1.000 HDSA2 VD 528308 21.500 23.500 1.000 HDSA1 RD 594356
514,35 25,40 546,10 596,90 25,40
18.500 20.500 0.968 HDSA2 VD 1850952 22.000 23.500 0.875 HDSA1 RD 2200920
469,90 520,70 24,59 558,80 596,90 22,23
19.250 20.750 0.875 HDSA1 RD 1925920 23.000 24.500 0.875 HDSB1 RD 2300921
488,95 527,05 22,23 584,20 622,30 22,23

seal width
d1 D b
in./mm – – –
24.000 26.250 0.875 HDSA2 RD 2400962

609,60 666,75 22,23
24.250 26.250 0.875 HDSA1 VD 2425950

2.15
615,95 666,75 22,23
25.000 27.500 1.000 HDSB1 RD 2500971

698,50 25,40
32.000 34.000 0.875 HDSA2 DD 3200958

812,80 863,60 22,23
45.000 46.627 1.000 HDSB2 RD 4500930

1 143,00 1 184,33 25,40
46.840 48.000 1.188 HDSA2 RD 4684912

1 189,74 1 219,20 30,18
Radial shaft seals – HDSE1 – metric dimensions

d1 850 mm
on page 214.
d1 D

seal width
d1 D b
mm – – –
850 910 50 HDSE1 RR 850¥910¥50 HDSE1 RR
2.16
Radial shaft seals – HDSD and HDSE seals – inch dimensions

d1 18.000 – 63.130 in.
on page 214.
d1 D

seal width
d1 D b
in./mm – – –
18.000 20.000 1.250 HDSD2 RR 1800570

457,20 508,00 31,75
20.000 1.500 HDSD1 RR 1800956
508,00 38,10
20.250 1.250 HDSE2 RR 1800966
514,35 31,75
18.500 20.000 1.250 HDSD2 RR 1850922

469,90 508,00 31,75
19.125 21.250 1.750 HDSD1 RR 1913960

485,78 539,75 44,45
20.000 22.000 1.813 HDSE1 RR 2000951

508,00 558,80 46,05
21.750 24.750 1.500 HDSD1 RR 2175920

552,45 628,65 38,10
24.750 1.500 HDSD2 VV 2175992
628,65 38,10
24.750 1.500 HDSD1 VV 2175997
628,65 38,10
24.750 1.500 HDSE1 VV 2175998
628,65 38,10
22.000 24.000 1.250 HDSD1 RR 2200953

558,80 609,60 31,75
24.000 1.250 HDSE2 DD 2200958
609,60 31,75
24.000 1.250 HDSD2 DD 2200962
609,60 31,75
23.000 24.750 1.250 HDSE1 VV 2300983

584,20 628,65 31,75
23.500 25.500 1.250 HDSD2 RR 2350955

596,90 647,70 31,75
25.500 28.500 1.250 HDSD2 RR 2550912

647,70 723,90 31,75

seal width
d1 D b
in./mm – – –
27.000 29.000 1.875 HDSE2 DD 2700953

685,80 736,60 47,63
27.688 29.812 1.250 HDSE2 RR 2769915

2.17
703,28 757,23 31,75
28.000 31.000 1.250 HDSD2 DD 2800998

711,20 787,40 31,75
29.000 31.000 1.750 HDSD1 RR 2900954

736,60 787,40 44,45
31.000 34.000 1.250 HDSD2 RR 3100992

787,40 863,60 31,75
33.000 34.500 1.250 HDSD1 RR 3300920

838,20 876,30 31,75
34.500 1.250 HDSE1 RR 3300921
876,30 31,75
33.500 35.500 1.750 HDSE1 RR 3350950

850,90 901,70 44,45
35.500 38.000 1.250 HDSE2 VV 3550974

901,70 965,20 31,75
36.000 38.000 1.500 HDSE2 RR 3600954

914,40 965,20 38,10
38.000 40.000 1.313 HDSE1 RR 3800950

965,20 1 016,00 33,35
63.130 64.625 1.375 HDSD1 RD 6313922

1 603,50 1 641,48 34,93
Radial shaft seals – SBF – metric dimensions

d1 175 – 900 mm
information.
d1 D
seal width R V
d1 D b
mm –
175 205 15 175¥205¥15 SBF R 175¥205¥15 SBF V
230 260 15 230¥260¥15 SBF R 230¥260¥15 SBF V
240 270 15 240¥270¥15 SBF R 240¥270¥15 SBF V

280 16 240¥280¥16 SBF R 240¥280¥16 SBF V
245 275 16 245¥275¥16 SBF R 245¥275¥16 SBF V
260 290 16 260¥290¥16 SBF R 260¥290¥16 SBF V

310 16 260¥310¥16 SBF R 260¥310¥16 SBF V
270 235 16 270¥235¥16 SBF R 270¥235¥16 SBF V
290 330 18 290¥330¥18 SBF R 290¥330¥18 SBF V

334 20 290¥334¥20 SBF R 290¥334¥20 SBF V
300 344 20 300¥344¥20 SBF R 300¥344¥20 SBF V
316 360 20 316¥360¥20 SBF R 316¥360¥20 SBF V
325 365 16 325¥365¥16 SBF R 325¥365¥16 SBF V
340 380 20 340¥380¥20 SBF R 340¥380¥20 SBF V
360 400 20 360¥400¥20 SBF R 360¥400¥20 SBF V
385 430 25 385¥430¥25 SBF R 385¥430¥25 SBF V
390 430 20 390¥430¥20 SBF R 390¥430¥20 SBF V
400 440 20 400¥440¥20 SBF R 400¥440¥20 SBF V
430 480 22 430¥480¥22 SBF R 430¥480¥22 SBF V
440 490 25 440¥490¥25 SBF R 440¥490¥25 SBF V
450 500 25 450¥500¥25 SBF R 450¥500¥25 SBF V
900 960 27 900¥960¥27 SBF R 900¥960¥27 SBF V
Radial shaft seals – SBF – inch dimensions

d1 11.000 – 27.500 in.
information.
d1 D
2.18
seal width R V
d1 D b
in./mm –
11.000 12.500 0.625 SBF 5809 R SBF 5809 V

279,40 317,50 15,88
20.500 22.500 0.875 SBF 7083 R SBF 7083 V

520,70 571,50 22,23
21.500 23.469 0.875 SBF 7175 R SBF 7175 V

546,10 596,10 22,23
23.000 24.500 0.750 SBF 7270 R SBF 7270 V

584,20 622,30 19,05
27.500 29.500 1.000 SBF 7406 R SBF 7406 V

698,50 749,30 25,40
Radial shaft seals – HSF1 (split) and HSF5 (solid) – metric dimensions
d1 40 – 215 mm
B The table includes only

Contact your SKF sales
information.
d1 D
Shaft Bore Bore Split version (HSF1) Solid version (HSF5)
diameter diameter depth Lip material R, V Lip material R, V
d1 D B
mm –
40 60 10 40¥60¥10 HSF1 R 40¥60¥10 HSF5 R

40¥60¥10 HSF1 V 40¥60¥10 HSF5 V
55 80 12,20 55¥80¥12 HSF1 R 55¥80¥12 HSF5 R

55¥80¥12 HSF1 V 55¥80¥12 HSF5 V
60 80 10 60¥80¥10 HSF1 R 60¥80¥10 HSF5 R

60¥80¥10 HSF1 V 60¥80¥10 HSF5 V
70 102 12,50 70¥102¥13 HSF1 R 70¥102¥13 HSF5 R

70¥102¥13 HSF1 V 70¥102¥13 HSF5 V
80 100 8 80¥100¥8 HSF1 R 80¥100¥8 HSF5 R

80¥100¥8 HSF1 V 80¥100¥8 HSF5 V
112 12,50 80¥112¥13 HSF1 R 80¥112¥13 HSF5 R
80¥112¥13 HSF1 V 80¥112¥13 HSF5 V
84 100 8 84¥100¥8 HSF1 R 84¥100¥8 HSF5 R

84¥100¥8 HSF1 V 84¥100¥8 HSF5 V
85 101 8 85¥101¥8 HSF1 R 85¥101¥8 HSF5 R

85¥101¥8 HSF1 V 85¥101¥8 HSF5 V
120 12 85¥120¥12 HSF1 R 85¥120¥12 HSF5 R
85¥120¥12 HSF1 V 85¥120¥12 HSF5 V
90 110 12 90¥110¥12 HSF1 R 90¥110¥12 HSF5 R

90¥110¥12 HSF1 V 90¥110¥12 HSF5 V
100 116 8 100¥116¥8 HSF1 R 100¥116¥8 HSF5 R

100¥116¥8 HSF1 V 100¥116¥8 HSF5 V
130 10 100¥130¥10 HSF1 R 100¥130¥10 HSF5 R
100¥130¥10 HSF1 V 100¥130¥10 HSF5 V
110 130 12 110¥130¥12 HSF1 R 110¥130¥12 HSF5 R

110¥130¥12 HSF1 V 110¥130¥12 HSF5 V
120 150 13 120¥150¥13 HSF1 R 120¥150¥13 HSF5 R

120¥150¥13 HSF1 V 120¥150¥13 HSF5 V
d1 D B
mm –
125 155 12,50 125¥155¥13 HSF1 R 125¥155¥13 HSF5 R

125¥155¥13 HSF1 V 125¥155¥13 HSF5 V

160 12 125¥160¥12 HSF1 R
125¥160¥12 HSF1 V
125¥160¥12 HSF5 R
125¥160¥12 HSF5 V
2.19
127 165 16 127¥165¥16 HSF1 R 127¥165¥16 HSF5 R
127¥165¥16 HSF1 V 127¥165¥16 HSF5 V
135 160 12 135¥160¥12 HSF1 R 135¥160¥12 HSF5 R

135¥160¥12 HSF1 V 135¥160¥12 HSF5 V
140 170 12 140¥170¥12 HSF1 R 140¥170¥12 HSF5 R

140¥170¥12 HSF1 V 140¥170¥12 HSF5 V
145 180 14 145¥180¥14 HSF1 R 145¥180¥14 HSF5 R

145¥180¥14 HSF1 V 145¥180¥14 HSF5 V
150 180 12 150¥180¥12 HSF1 R 150¥180¥12 HSF5 R

150¥180¥12 HSF1 V 150¥180¥12 HSF5 V
160 190 15 160¥190¥15 HSF1 R 160¥190¥15 HSF5 R

160¥190¥15 HSF1 V 160¥190¥15 HSF5 V
200 10 160¥200¥10 HSF1 R 160¥200¥10 HSF5 R
160¥200¥10 HSF1 V 160¥200¥10 HSF5 V
170 200 12 170¥200¥12 HSF1 R 170¥200¥12 HSF5 R

170¥200¥12 HSF1 V 170¥200¥12 HSF5 V
200 16 170¥200¥16 HSF1 R 170¥200¥16 HSF5 R
170¥200¥16 HSF1 V 170¥200¥16 HSF5 V
211 16 170¥211¥16 HSF1 R 170¥211¥16 HSF5 R
170¥211¥16 HSF1 V 170¥211¥16 HSF5 V
175 200 15 175¥200¥15 HSF1 R 175¥200¥15 HSF5 R

175¥200¥15 HSF1 V 175¥200¥15 HSF5 V
180 200 15 180¥200¥15 HSF1 R 180¥200¥15 HSF5 R

180¥200¥15 HSF1 V 180¥200¥15 HSF5 V
222 16 180¥222¥16 HSF1 R 180¥222¥16 HSF5 R
180¥222¥16 HSF1 V 180¥222¥16 HSF5 V
185 225 16 185¥225¥16 HSF1 R 185¥225¥16 HSF5 R

185¥225¥16 HSF1 V 185¥225¥16 HSF5 V
190 220 15 190¥220¥15 HSF1 R 190¥220¥15 HSF5 R

190¥220¥15 HSF1 V 190¥220¥15 HSF5 V
225 18 190¥225¥18 HSF1 R 190¥225¥18 HSF5 R
190¥225¥18 HSF1 V 190¥225¥18 HSF5 V
230 16 190¥230¥16 HSF1 R 190¥230¥16 HSF5 R
190¥230¥16 HSF1 V 190¥230¥16 HSF5 V
200 240 16 200¥240¥16 HSF1 R 200¥240¥16 HSF5 R

200¥240¥16 HSF1 V 200¥240¥16 HSF5 V
250 18 200¥250¥18 HSF1 R 200¥250¥18 HSF5 R
200¥250¥18 HSF1 V 200¥250¥18 HSF5 V
210 240 12 210¥240¥12 HSF1 R 210¥240¥12 HSF5 R

210¥240¥12 HSF1 V 210¥240¥12 HSF5 V
250 16 210¥250¥16 HSF1 R 210¥250¥16 HSF5 R
210¥250¥16 HSF1 V 210¥250¥16 HSF5 V
215 248 15 215¥248¥15 HSF1 R 215¥248¥15 HSF5 R

215¥248¥15 HSF1 V 215¥248¥15 HSF5 V
250 16 215¥250¥16 HSF1 R 215¥250¥16 HSF5 R
215¥250¥16 HSF1 V 215¥250¥16 HSF5 V
d1 220 – 335 mm

information.
d1 D
d1 D B
mm –
220 180 16 220¥180¥16 HSF1 R 220¥180¥16 HSF5 R

220¥180¥16 HSF1 V 220¥180¥16 HSF5 V
260 16 220¥260¥16 HSF1 R 220¥260¥16 HSF5 R
220¥260¥16 HSF1 V 220¥260¥16 HSF5 V
226 276 22,22 226¥276¥22 HSF1 R 226¥276¥22 HSF5 R

226¥276¥22 HSF1 V 226¥276¥22 HSF5 V
230 260 15 230¥260¥15 HSF1 R 230¥260¥15 HSF5 R

230¥260¥15 HSF1 V 230¥260¥15 HSF5 V
270 16 230¥270¥16 HSF1 R 230¥270¥16 HSF5 R
230¥270¥16 HSF1 V 230¥270¥16 HSF5 V
235 265 15 235¥265¥15 HSF1 R 235¥265¥15 HSF5 R

235¥265¥15 HSF1 V 235¥265¥15 HSF5 V
275 20 235¥275¥20 HSF1 R 235¥275¥20 HSF5 R
235¥275¥20 HSF1 V 235¥275¥20 HSF5 V
236 276 16 236¥276¥16 HSF1 R 236¥276¥16 HSF5 R

236¥276¥16 HSF1 V 236¥276¥16 HSF5 V
240 275 18 240¥275¥18 HSF1 R 240¥275¥18 HSF5 R

240¥275¥18 HSF1 V 240¥275¥18 HSF5 V
280 18 240¥280¥18 HSF1 R 240¥280¥18 HSF5 R
240¥280¥18 HSF1 V 240¥280¥18 HSF5 V
290 25 240¥290¥25 HSF1 R 240¥290¥25 HSF5 R
240¥290¥25 HSF1 V 240¥290¥25 HSF5 V
250 280 15 250¥280¥15 HSF1 R 250¥280¥15 HSF5 R

250¥280¥15 HSF1 V 250¥280¥15 HSF5 V
290 16,50 250¥290¥17 HSF1 R 250¥290¥17 HSF5 R
250¥290¥17 HSF1 V 250¥290¥17 HSF5 V
260 290 16 260¥290¥16 HSF1 R 260¥290¥16 HSF5 R

260¥290¥16 HSF1 V 260¥290¥16 HSF5 V
304 20 260¥304¥20 HSF1 R 260¥304¥20 HSF5 R
260¥304¥20 HSF1 V 260¥304¥20 HSF5 V
270 310 15 270¥310¥15 HSF1 R 270¥310¥15 HSF5 R

270¥310¥15 HSF1 V 270¥310¥15 HSF5 V
314 20 270¥314¥20 HSF1 R 270¥314¥20 HSF5 R
270¥314¥20 HSF1 V 270¥314¥20 HSF5 V
d1 D B
mm –
275 315 20 275¥315¥20 HSF1 R 275¥315¥20 HSF5 R

275¥315¥20 HSF1 V 275¥315¥20 HSF5 V
280 320 16 280¥320¥16 HSF1 R 280¥320¥16 HSF5 R

2.19
280¥320¥16 HSF1 V 280¥320¥16 HSF5 V
320 20 280¥320¥20 HSF1 R 280¥320¥20 HSF5 R
280¥320¥20 HSF1 V 280¥320¥20 HSF5 V
324 20 280¥324¥20 HSF1 R 280¥324¥20 HSF5 R
280¥324¥20 HSF1 V 280¥324¥20 HSF5 V
285 310 15 285¥310¥15 HSF1 R 285¥310¥15 HSF5 R

285¥310¥15 HSF1 V 285¥310¥15 HSF5 V
289 327 19 289¥327¥19 HSF1 R 289¥327¥19 HSF5 R

289¥327¥19 HSF1 V 289¥327¥19 HSF5 V
290 330 20 290¥330¥20 HSF1 R 290¥330¥20 HSF5 R

290¥330¥20 HSF1 V 290¥330¥20 HSF5 V
334 20 290¥334¥20 HSF1 R 290¥334¥20 HSF5 R
290¥334¥20 HSF1 V 290¥334¥20 HSF5 V
292 330 15,87 292¥330¥16 HSF1 R 292¥330¥16 HSF5 R

292¥330¥16 HSF1 V 292¥330¥16 HSF5 V
300 340 16,50 300¥340¥17 HSF1 R 300¥340¥17 HSF5 R

300¥340¥17 HSF1 V 300¥340¥17 HSF5 V
340 20 300¥340¥20 HSF1 R 300¥340¥20 HSF5 R
300¥340¥20 HSF1 V 300¥340¥20 HSF5 V
304 348 20 304¥348¥20 HSF1 R 304¥348¥20 HSF5 R

304¥348¥20 HSF1 V 304¥348¥20 HSF5 V
308 352 20 308¥352¥20 HSF1 R 308¥352¥20 HSF5 R

308¥352¥20 HSF1 V 308¥352¥20 HSF5 V
310 345 18 310¥345¥18 HSF1 R 310¥345¥18 HSF5 R

310¥345¥18 HSF1 V 310¥345¥18 HSF5 V
354 20,50 310¥354¥21 HSF1 R 310¥354¥21 HSF5 R
310¥354¥21 HSF1 V 310¥354¥21 HSF5 V
311 345 18,30 311¥345¥18 HSF1 R 311¥345¥18 HSF5 R

311¥345¥18 HSF1 V 311¥345¥18 HSF5 V
314 355 20 314¥355¥20 HSF1 R 314¥355¥20 HSF5 R

314¥355¥20 HSF1 V 314¥355¥20 HSF5 V
316 360 20 316¥360¥20 HSF1 R 316¥360¥20 HSF5 R

316¥360¥20 HSF1 V 316¥360¥20 HSF5 V
320 350 15 320¥350¥15 HSF1 R 320¥350¥15 HSF5 R

320¥350¥15 HSF1 V 320¥350¥15 HSF5 V
360 18 320¥360¥18 HSF1 R 320¥360¥18 HSF5 R
320¥360¥18 HSF1 V 320¥360¥18 HSF5 V
328 372 20,20 328¥372¥20 HSF1 R 328¥372¥20 HSF5 R

328¥372¥20 HSF1 V 328¥372¥20 HSF5 V
330 370 18 330¥370¥18 HSF1 R 330¥370¥18 HSF5 R

330¥370¥18 HSF1 V 330¥370¥18 HSF5 V
374 20 330¥374¥20 HSF1 R 330¥374¥20 HSF5 R
330¥374¥20 HSF1 V 330¥374¥20 HSF5 V
335 373 19 335¥373¥19 HSF1 R 335¥373¥19 HSF5 R

335¥373¥19 HSF1 V 335¥373¥19 HSF5 V
d1 340 – 530 mm

information.
d1 D
d1 D B
mm –
340 380 16 CR340¥380¥16 HSF1 R 340¥380¥16 HSF5 R

340¥380¥16 HSF1 V 340¥380¥16 HSF5 V
380 20 340¥380¥20 HSF1 R 340¥380¥20 HSF5 R
340¥380¥20 HSF1 V 340¥380¥20 HSF5 V
350 380 17,70 350¥380¥18 HSF1 R 350¥380¥18 HSF5 R

350¥380¥18 HSF1 V 350¥380¥18 HSF5 V
394 20 350¥394¥20 HSF1 R 350¥394¥20 HSF5 R
350¥394¥20 HSF1 V 350¥394¥20 HSF5 V
360 404 20 360¥404¥20 HSF1 R 360¥404¥20 HSF5 R

360¥404¥20 HSF1 V 360¥404¥20 HSF5 V
410 20 360¥410¥20 HSF1 R 360¥410¥20 HSF5 R
360¥410¥20 HSF1 V 360¥410¥20 HSF5 V
362 400 20 362¥400¥20 HSF1 R 362¥400¥20 HSF5 R

362¥400¥20 HSF1 V 362¥400¥20 HSF5 V
406 22 362¥406¥22 HSF1 R 362¥406¥22 HSF5 R
362¥406¥22 HSF1 V 362¥406¥22 HSF5 V
370 410 20 370¥410¥20 HSF1 R 370¥410¥20 HSF5 R

370¥410¥20 HSF1 V 370¥410¥20 HSF5 V
414 20 370¥414¥20 HSF1 R 370¥414¥20 HSF5 R
370¥414¥20 HSF1 V 370¥414¥20 HSF5 V
380 420 20 380¥420¥20 HSF1 R 380¥420¥20 HSF5 R

380¥420¥20 HSF1 V 380¥420¥20 HSF5 V
387 431 22,50 387¥431¥23 HSF1 R 387¥431¥23 HSF5 R

387¥431¥23 HSF1 V 387¥431¥23 HSF5 V
438 25,40 387¥438¥25 HSF1 R 387¥438¥25 HSF5 R
387¥438¥25 HSF1 V 387¥438¥25 HSF5 V
390 430 20 390¥430¥20 HSF1 R 390¥430¥20 HSF5 R

390¥430¥20 HSF1 V 390¥430¥20 HSF5 V
395 439 20 395¥439¥20 HSF1 R 395¥439¥20 HSF5 R

395¥439¥20 HSF1 V 395¥439¥20 HSF5 V
439 20,50 395¥439¥21 HSF1 R 395¥439¥21 HSF5 R
395¥439¥21 HSF1 V 395¥439¥21 HSF5 V
d1 D B
mm –
400 440 20 400¥440¥20 HSF1 R 400¥440¥20 HSF5 R

400¥440¥20 HSF1 V 400¥440¥20 HSF5 V

450 22 400¥450¥22 HSF1 R
400¥450¥22 HSF1 V
400¥450¥22 HSF5 R
400¥450¥22 HSF5 V
2.19
420 460 20 420¥460¥20 HSF1 R 420¥460¥20 HSF5 R
420¥460¥20 HSF1 V 420¥460¥20 HSF5 V
470 25 420¥470¥25 HSF1 R 420¥470¥25 HSF5 R
420¥470¥25 HSF1 V 420¥470¥25 HSF5 V
430 480 25 430¥480¥25 HSF1 R 430¥480¥25 HSF5 R

430¥480¥25 HSF1 V 430¥480¥25 HSF5 V
435 485 22 435¥485¥22 HSF1 R 435¥485¥22 HSF5 R

435¥485¥22 HSF1 V 435¥485¥22 HSF5 V
438 476 24 438¥476¥24 HSF1 R 438¥476¥24 HSF5 R

438¥476¥24 HSF1 V 438¥476¥24 HSF5 V
440 480 20 440¥480¥20 HSF1 R 440¥480¥20 HSF5 R

440¥480¥20 HSF1 V 440¥480¥20 HSF5 V
490 20 440¥490¥20 HSF1 R 440¥490¥20 HSF5 R
440¥490¥20 HSF1 V 440¥490¥20 HSF5 V
446 486 16,50 446¥486¥17 HSF1 R 446¥486¥17 HSF5 R

446¥486¥17 HSF1 V 446¥486¥17 HSF5 V
450 490 18 450¥490¥18 HSF1 R 450¥490¥18 HSF5 R

450¥490¥18 HSF1 V 450¥490¥18 HSF5 V
500 22 450¥500¥22 HSF1 R 450¥500¥22 HSF5 R
450¥500¥22 HSF1 V 450¥500¥22 HSF5 V
460 510 22 460¥510¥22 HSF1 R 460¥510¥22 HSF5 R

460¥510¥22 HSF1 V 460¥510¥22 HSF5 V
510 25 460¥510¥25 HSF1 R 460¥510¥25 HSF5 R
460¥510¥25 HSF1 V 460¥510¥25 HSF5 V
470 520 25 470¥520¥25 HSF1 R 470¥520¥25 HSF5 R

470¥520¥25 HSF1 V 470¥520¥25 HSF5 V
480 520 18 480¥520¥18 HSF1 R 480¥520¥18 HSF5 R

480¥520¥18 HSF1 V 480¥520¥18 HSF5 V
530 22 480¥530¥22 HSF1 R 480¥530¥22 HSF5 R
480¥530¥22 HSF1 V 480¥530¥22 HSF5 V
550 25 480¥550¥25 HSF1 R 480¥550¥25 HSF5 R
480¥550¥25 HSF1 V 480¥550¥25 HSF5 V
495 545 22 495¥545¥22 HSF1 R 495¥545¥22 HSF5 R

495¥545¥22 HSF1 V 495¥545¥22 HSF5 V
500 540 10 500¥540¥10 HSF1 R 500¥540¥10 HSF5 R

500¥540¥10 HSF1 V 500¥540¥10 HSF5 V
550 20 500¥550¥20 HSF1 R 500¥550¥20 HSF5 R
500¥550¥20 HSF1 V 500¥550¥20 HSF5 V
520 560 18 520¥560¥18 HSF1 R 520¥560¥18 HSF5 R

520¥560¥18 HSF1 V 520¥560¥18 HSF5 V
560 20 520¥560¥20 HSF1 R 520¥560¥20 HSF5 R
520¥560¥20 HSF1 V 520¥560¥20 HSF5 V
525 575 22 525¥575¥22 HSF1 R 525¥575¥22 HSF5 R

525¥575¥22 HSF1 V 525¥575¥22 HSF5 V
530 580 22 530¥580¥22 HSF1 R 530¥580¥22 HSF5 R

530¥580¥22 HSF1 V 530¥580¥22 HSF5 V
580 25 530¥580¥25 HSF1 R 530¥580¥25 HSF5 R
530¥580¥25 HSF1 V 530¥580¥25 HSF5 V
d1 535 – 840 mm

information.
d1 D
d1 D B
mm –
535 585 22 535¥585¥22 HSF1 R 535¥585¥22 HSF5 R

535¥585¥22 HSF1 V 535¥585¥22 HSF5 V
540 590 22 540¥590¥22 HSF1 R 540¥590¥22 HSF5 R

540¥590¥22 HSF1 V 540¥590¥22 HSF5 V
590 30 540¥590¥30 HSF1 R 540¥590¥30 HSF5 R
540¥590¥30 HSF1 V 540¥590¥30 HSF5 V
550 600 22,30 550¥600¥22 HSF1 R 550¥600¥22 HSF5 R

550¥600¥22 HSF1 V 550¥600¥22 HSF5 V
560 604 20 560¥604¥20 HSF1 R 560¥604¥20 HSF5 R

560¥604¥20 HSF1 V 560¥604¥20 HSF5 V
610 22,30 560¥610¥22 HSF1 R 560¥610¥22 HSF5 R
560¥610¥22 HSF1 V 560¥610¥22 HSF5 V
570 616 19 570¥616¥19 HSF1 R 570¥616¥19 HSF5 R

570¥616¥19 HSF1 V 570¥616¥19 HSF5 V
620 25 570¥620¥25 HSF1 R 570¥620¥25 HSF5 R
570¥620¥25 HSF1 V 570¥620¥25 HSF5 V
575 625 22 575¥625¥22 HSF1 R 575¥625¥22 HSF5 R

575¥625¥22 HSF1 V 575¥625¥22 HSF5 V
580 630 22 580¥630¥22 HSF1 R 580¥630¥22 HSF5 R

580¥630¥22 HSF1 V 580¥630¥22 HSF5 V
600 650 22 600¥650¥22 HSF1 R 600¥650¥22 HSF5 R

600¥650¥22 HSF1 V 600¥650¥22 HSF5 V
620 670 22 620¥670¥22 HSF1 R 620¥670¥22 HSF5 R

620¥670¥22 HSF1 V 620¥670¥22 HSF5 V
684 25 620¥684¥25 HSF1 R 620¥684¥25 HSF5 R
620¥684¥25 HSF1 V 620¥684¥25 HSF5 V
625 689 25 625¥689¥25 HSF1 R 625¥689¥25 HSF5 R

625¥689¥25 HSF1 V 625¥689¥25 HSF5 V
630 690 30 630¥690¥30 HSF1 R 630¥690¥30 HSF5 R

630¥690¥30 HSF1 V 630¥690¥30 HSF5 V
d1 D B
mm –
635 705 30 635¥705¥30 HSF1 R 635¥705¥30 HSF5 R

635¥705¥30 HSF1 V 635¥705¥30 HSF5 V
650 690 18 650¥690¥18 HSF1 R 650¥690¥18 HSF5 R

2.19
650¥690¥18 HSF1 V 650¥690¥18 HSF5 V
660 724 25 660¥724¥25 HSF1 R 660¥724¥25 HSF5 R

660¥724¥25 HSF1 V 660¥724¥25 HSF5 V
670 734 25 670¥734¥25 HSF1 R 670¥734¥25 HSF5 R

670¥734¥25 HSF1 V 670¥734¥25 HSF5 V
685 749 25 685¥749¥25 HSF1 R 685¥749¥25 HSF5 R

685¥749¥25 HSF1 V 685¥749¥25 HSF5 V
700 760 30 700¥760¥30 HSF1 R 700¥760¥30 HSF5 R

700¥760¥30 HSF1 V 700¥760¥30 HSF5 V
710 770 30 710¥770¥30 HSF1 R 710¥770¥30 HSF5 R

710¥770¥30 HSF1 V 710¥770¥30 HSF5 V
774 25 710¥774¥25 HSF1 R 710¥774¥25 HSF5 R
710¥774¥25 HSF1 V 710¥774¥25 HSF5 V
730 794 25 730¥794¥25 HSF1 R 730¥794¥25 HSF5 R

730¥794¥25 HSF1 V 730¥794¥25 HSF5 V
736 800 25 736¥800¥25 HSF1 R 736¥800¥25 HSF5 R

736¥800¥25 HSF1 V 736¥800¥25 HSF5 V
740 785 18 740¥785¥18 HSF1 R 740¥785¥18 HSF5 R

740¥785¥18 HSF1 V 740¥785¥18 HSF5 V
744 808 25 744¥808¥25 HSF1 R 744¥808¥25 HSF5 R

744¥808¥25 HSF1 V 744¥808¥25 HSF5 V
750 810 30 750¥810¥30 HSF1 R 750¥810¥30 HSF5 R

750¥810¥30 HSF1 V 750¥810¥30 HSF5 V
814 25 750¥814¥25 HSF1 R 750¥814¥25 HSF5 R
750¥814¥25 HSF1 V 750¥814¥25 HSF5 V
760 820 30 760¥820¥30 HSF1 R 760¥820¥30 HSF5 R

760¥820¥30 HSF1 V 760¥820¥30 HSF5 V
770 834 25 770¥834¥25 HSF1 R 770¥834¥25 HSF5 R

770¥834¥25 HSF1 V 770¥834¥25 HSF5 V
780 844 25 780¥844¥25 HSF1 R 780¥844¥25 HSF5 R

780¥844¥25 HSF1 V 780¥844¥25 HSF5 V
790 850 30 790¥850¥30 HSF1 R 790¥850¥30 HSF5 R

790¥850¥30 HSF1 V 790¥850¥30 HSF5 V
800 860 30 800¥860¥30 HSF1 R 800¥860¥30 HSF5 R

800¥860¥30 HSF1 V 800¥860¥30 HSF5 V
865 25 800¥865¥25 HSF1 R 800¥865¥25 HSF5 R
800¥865¥25 HSF1 V 800¥865¥25 HSF5 V
810 860 25 810¥860¥25 HSF1 R 810¥860¥25 HSF5 R

810¥860¥25 HSF1 V 810¥860¥25 HSF5 V
874 22 810¥874¥22 HSF1 R 810¥874¥22 HSF5 R
810¥874¥22 HSF1 V 810¥874¥22 HSF5 V
840 904 25 840¥904¥25 HSF1 R 840¥904¥25 HSF5 R

840¥904¥25 HSF1 V 840¥904¥25 HSF5 V
d1 850 – 1 110 mm

information.
d1 D
d1 D B
mm –
850 900 22 850¥900¥22 HSF1 R 850¥900¥22 HSF5 R

850¥900¥22 HSF1 V 850¥900¥22 HSF5 V
904 25 850¥904¥25 HSF1 R 850¥904¥25 HSF5 R
850¥904¥25 HSF1 V 850¥904¥25 HSF5 V
910 30 850¥910¥30 HSF1 R 850¥910¥30 HSF5 R
850¥910¥30 HSF1 V 850¥910¥30 HSF5 V
900 960 30 900¥960¥30 HSF1 R 900¥960¥30 HSF5 R

900¥960¥30 HSF1 V 900¥960¥30 HSF5 V
964 32 900¥964¥32 HSF1 R 900¥964¥32 HSF5 R
900¥964¥32 HSF1 V 900¥964¥32 HSF5 V
910 974 25 910¥974¥25 HSF1 R 910¥974¥25 HSF5 R

910¥974¥25 HSF1 V 910¥974¥25 HSF5 V
974 25,40 910¥974¥25 HSF1 R 910¥974¥25 HSF5 R
910¥974¥25 HSF1 V 910¥974¥25 HSF5 V
920 984 25 920¥984¥25 HSF1 R 920¥984¥25 HSF5 R

920¥984¥25 HSF1 V 920¥984¥25 HSF5 V
950 1 000 25 950¥1000¥25 HSF1 R 950¥1000¥25 HSF5 R

950¥1000¥25 HSF1 V 950¥1000¥25 HSF5 V
1 010 30 950¥1010¥30 HSF1 R 950¥1010¥30 HSF5 R
950¥1010¥30 HSF1 V 950¥1010¥30 HSF5 V
960 1 024 25 960¥1024¥25 HSF1 R 960¥1024¥25 HSF5 R

960¥1024¥25 HSF1 V 960¥1024¥25 HSF5 V
970 1 020 25 970¥1020¥25 HSF1 R 970¥1020¥25 HSF5 R

970¥1020¥25 HSF1 V 970¥1020¥25 HSF5 V
1 034 25 970¥1034¥25 HSF1 R 970¥1034¥25 HSF5 R
970¥1034¥25 HSF1 V 970¥1034¥25 HSF5 V
1 000 1 064 25 1000¥1064¥25 HSF1 R 1000¥1064¥25 HSF5 R

1000¥1064¥25 HSF1 V 1000¥1064¥25 HSF5 V
1 016 1 043,10 13,70 1016¥1043¥14 HSF1 R 1016¥1043¥14 HSF5 R

1016¥1043¥14 HSF1 V 1016¥1043¥14 HSF5 V
1 110 1 174 25 1110¥1174¥25 HSF1 R 1110¥1174¥25 HSF5 R

1110¥1174¥25 HSF1 V 1110¥1174¥25 HSF5 V
Radial shaft seals – HSF1 (split) and HSF5 (solid) – inch dimensions
d1 1.000 – 5.874 in.

information.
d1 D
2.19
diameter diameter depth Lip material Lip material
d1 D B R V R V
in./mm –
1.000 1.874 0.375 HSF1 5001 R HSF1 5001 V HSF5 5001 R HSF5 5001 V
25,40 47,60 9,53

69,85 85,73 7,95

82,50 114,30 12,70

88,90 114,30 12,70

98,40 123,90 12,70

101,60 127,00 12,70

112,40 139,70 14,27

112,70 138,81 14,81

123,80 149,20 12,70

132,21 165,20 15,01

142,80 168,20 15,88

146,05 177,80 15,88

149,20 177,80 12,50

d1 6.000 – 17.000 in.

information.
d1 D
d1 D B R V R V
in./mm –
152,40 181,00 16,00
7.500 0.625 HSF1 5510 R HSF1 5510 V HSF5 5510 R HSF5 5510 V
190,50 15,88

165,10 203,20 19,05

171,40 196,85 19,05

177,80 203,20 11,10
209,55 19,05

184,15 215,90 15,88

190,50 215,90 15,88

195,00 220,40 12,70

218,39 250,01 15,01

222,25 254,00 15,88

244,48 295,53 25,40

250,01 275,41 12,70

254,00 285,75 15,88

260,35 311,15 19,05

d1 D B R V R V
in./mm –
279,40 309,40 15,01

2.19
285,75 317,50 15,88

286,00 336,55 15,01

289,99 315,39 12,70

311,15 361,95 20,65

317,09 355,60 16,00

317,50 355,60 19,05

317,60 355,60 17,45

323,75 361,90 17,45
374,65 25,40

330,20 368,30 17,45
368,30 17,45

342,90 381,00 19,05

365,00 409,40 19,05

368,30 412,75 15,88

380,01 430,81 20,65

387,35 438,15 22,23

406,20 444,50 17,45

406,40 457,20 19,05
457,20 20,65
457,20 23,01

412,14 450,85 17,45

419,10 450,85 19,05

431,80 482,60 20,65

d1 17.248 – 48.000 in.

information.
d1 D
d1 D B R V R V
in./mm –
438,10 476,20 19,05

461,49 540,00 30,99

520,70 571,50 25,40

533,40 584,20 22,23

558,80 609,60 22,23

590,50 641,35 20,65

596,93 558,83 19,05

762,00 825,50 25,40

773,71 825,50 23,01

787,40 838,20 23,01

793,75 844,55 19,05

825,50 876,30 22,23
876,30 25,40

838,20 889,00 23,01

d1 D B R V R V
in./mm –
873,13 936,63 31,75

2.19
927,10 990,60 31,75

933,40 984,22 22,23

965,20 1016,00 22,23

993,60 1016,00 12,70

1219,20 1244,60 32,00
d1 127 – 800 mm

information.
d1 D
d1 D B
mm –
127 158,80 12,30 127¥159¥12 HSF2 R 127¥159¥12 HSF6 R

127¥159¥12 HSF2 V 127¥159¥12 HSF6 V
275 319,50 19 275¥320¥19 HSF2 R 275¥320¥19 HSF6 R

275¥320¥19 HSF2 V 275¥320¥19 HSF6 V
320 364 18 320¥364¥18 HSF2 R 320¥364¥18 HSF6 R

320¥364¥18 HSF2 V 320¥364¥18 HSF6 V
800 864 21,60 800¥864¥22 HSF2 R 800¥864¥22 HSF6 R

800¥864¥22 HSF2 V 800¥864¥22 HSF6 V
d1 21.000 in.

information.
d1 D
2.20
d1 D B R V R V
in./mm –
533,40 584,20 22,23
d1 80 – 380 mm

information.
d1 D
d1 D B
mm –
80 95 10 80¥95¥10 HSF3 R 80¥95¥10 HSF7 R

80¥95¥10 HSF3 V 80¥95¥10 HSF7 V
100 130 12,50 100¥130¥13 HSF3 R 100¥130¥13 HSF7 R

100¥130¥13 HSF3 V 100¥130¥13 HSF7 V
140 180 16 140¥180¥16 HSF3 R 140¥180¥16 HSF7 R

140¥180¥16 HSF3 V 140¥180¥16 HSF7 V
150 190 16 150¥190¥16 HSF3 R 150¥190¥16 HSF7 R

150¥190¥16 HSF3 V 150¥190¥16 HSF7 V
160 200 16 160¥200¥16 HSF3 R 160¥200¥16 HSF7 R

160¥200¥16 HSF3 V 160¥200¥16 HSF7 V
165 195 15 165¥195¥15 HSF3 R 165¥195¥15 HSF7 R

165¥195¥15 HSF3 V 165¥195¥15 HSF7 V
220 250 15 220¥250¥15 HSF3 R 220¥250¥15 HSF7 R

220¥250¥15 HSF3 V 220¥250¥15 HSF7 V
260 18 220¥260¥18 HSF3 R 220¥260¥18 HSF7 R
220¥260¥18 HSF3 V 220¥260¥18 HSF7 V
230 270 16 230¥270¥16 HSF3 R 230¥270¥16 HSF7 R

230¥270¥16 HSF3 V 230¥270¥16 HSF7 V
235 265 15,30 235¥265¥15 HSF3 R 235¥265¥15 HSF7 R

235¥265¥15 HSF3 V 235¥265¥15 HSF7 V
240 280 18 240¥280¥18 HSF3 R 240¥280¥18 HSF7 R

240¥280¥18 HSF3 V 240¥280¥18 HSF7 V
290 25 240¥290¥25 HSF3 R 240¥290¥25 HSF7 R
240¥290¥25 HSF3 V 240¥290¥25 HSF7 V
245 285 16 245¥285¥16 HSF3 R 245¥285¥16 HSF7 R

245¥285¥16 HSF3 V 245¥285¥16 HSF7 V
250 280 16 250¥280¥16 HSF3 R 250¥280¥16 HSF7 R

250¥280¥16 HSF3 V 250¥280¥16 HSF7 V
290 16,50 250¥290¥17 HSF3 R 250¥290¥17 HSF7 R
250¥290¥17 HSF3 V 250¥290¥17 HSF7 V
d1 D B
mm –
270 310 18 270¥310¥18 HSF3 R 270¥310¥18 HSF7 R

270¥310¥18 HSF3 V 270¥310¥18 HSF7 V
280 320 18 280¥320¥18 HSF3 R 280¥320¥18 HSF7 R

2.21
280¥320¥18 HSF3 V 280¥320¥18 HSF7 V
285 325 18 285¥325¥18 HSF3 R 285¥325¥18 HSF7 R

285¥325¥18 HSF3 V 285¥325¥18 HSF7 V
290 334 20,30 290¥334¥20 HSF3 R 290¥334¥20 HSF7 R

290¥334¥20 HSF3 V 290¥334¥20 HSF7 V
300 340 16,50 300¥340¥17 HSF3 R 300¥340¥17 HSF7 R

300¥340¥17 HSF3 V 300¥340¥17 HSF7 V
340 18 300¥340¥18 HSF3 R 300¥340¥18 HSF7 R
300¥340¥18 HSF3 V 300¥340¥18 HSF7 V
344 20 300¥344¥20 HSF3 R 300¥344¥20 HSF7 R
300¥344¥20 HSF3 V 300¥344¥20 HSF7 V
310 353 20 310¥353¥20 HSF3 R 310¥353¥20 HSF7 R

310¥353¥20 HSF3 V 310¥353¥20 HSF7 V
354 20 310¥354¥20 HSF3 R 310¥354¥20 HSF7 R
310¥354¥20 HSF3 V 310¥354¥20 HSF7 V
315 360 20 315¥360¥20 HSF3 R 315¥360¥20 HSF7 R

315¥360¥20 HSF3 V 315¥360¥20 HSF7 V
320 350 15 320¥350¥15 HSF3 R 320¥350¥15 HSF7 R

320¥350¥15 HSF3 V 320¥350¥15 HSF7 V
360 17,70 320¥360¥18 HSF3 R 320¥360¥18 HSF7 R
320¥360¥18 HSF3 V 320¥360¥18 HSF7 V
325 365 16 325¥365¥16 HSF3 R 325¥365¥16 HSF7 R

325¥365¥16 HSF3 V 325¥365¥16 HSF7 V
330 370 20 330¥370¥20 HSF3 R 330¥370¥20 HSF7 R

330¥370¥20 HSF3 V 330¥370¥20 HSF7 V
374 20 330¥374¥20 HSF3 R 330¥374¥20 HSF7 R
330¥374¥20 HSF3 V 330¥374¥20 HSF7 V
340 372 16 340¥372¥16 HSF3 R 340¥372¥16 HSF7 R

340¥372¥16 HSF3 V 340¥372¥16 HSF7 V
345 389 20 345¥389¥20 HSF3 R 345¥389¥20 HSF7 R

345¥389¥20 HSF3 V 345¥389¥20 HSF7 V
350 390 18 350¥390¥18 HSF3 R 350¥390¥18 HSF7 R

350¥390¥18 HSF3 V 350¥390¥18 HSF7 V
394 20 350¥394¥20 HSF3 R 350¥394¥20 HSF7 R
350¥394¥20 HSF3 V 350¥394¥20 HSF7 V
394 22 350¥394¥22 HSF3 R 350¥394¥22 HSF7 R
350¥394¥22 HSF3 V 350¥394¥22 HSF7 V
360 404 20 360¥404¥20 HSF3 R 360¥404¥20 HSF7 R

360¥404¥20 HSF3 V 360¥404¥20 HSF7 V
365 409,40 19,05 365¥409¥19 HSF3 R 365¥409¥19 HSF7 R

365¥409¥19 HSF3 V 365¥409¥19 HSF7 V
366 410 20 366¥410¥20 HSF3 R 366¥410¥20 HSF7 R

366¥410¥20 HSF3 V 366¥410¥20 HSF7 V
370 410 18 370¥410¥18 HSF3 R 370¥410¥18 HSF7 R

370¥410¥18 HSF3 V 370¥410¥18 HSF7 V
380 419 24 380¥419¥24 HSF3 R 380¥419¥24 HSF7 R

380¥419¥24 HSF3 V 380¥419¥24 HSF7 V
424 20 380¥424¥20 HSF3 R 380¥424¥20 HSF7 R
380¥424¥20 HSF3 V 380¥424¥20 HSF7 V
d1 385 – 750 mm

information.
d1 D
d1 D B
mm –
385 425 18,30 385¥425¥18 HSF3 R 385¥425¥18 HSF7 R

385¥425¥18 HSF3 V 385¥425¥18 HSF7 V
387 431 22,50 387¥431¥23 HSF3 R 387¥431¥23 HSF7 R

387¥431¥23 HSF3 V 387¥431¥23 HSF7 V
390 430 18 390¥430¥18 HSF3 R 390¥430¥18 HSF7 R

390¥430¥18 HSF3 V 390¥430¥18 HSF7 V
400 440 18 400¥440¥18 HSF3 R 400¥440¥18 HSF7 R

400¥440¥18 HSF3 V 400¥440¥18 HSF7 V
440 22 400¥440¥22 HSF3 R 400¥440¥22 HSF7 R
400¥440¥22 HSF3 V 400¥440¥22 HSF7 V
444 20 400¥444¥20 HSF3 R 400¥444¥20 HSF7 R
400¥444¥20 HSF3 V 400¥444¥20 HSF7 V
450 22 400¥450¥22 HSF3 R 400¥450¥22 HSF7 R
400¥450¥22 HSF3 V 400¥450¥22 HSF7 V
420 470 22 420¥470¥22 HSF3 R 420¥470¥22 HSF7 R

420¥470¥22 HSF3 V 420¥470¥22 HSF7 V
430 480 22 430¥480¥22 HSF3 R 430¥480¥22 HSF7 R

430¥480¥22 HSF3 V 430¥480¥22 HSF7 V
440 490 22 440¥490¥22 HSF3 R 440¥490¥22 HSF7 R

440¥490¥22 HSF3 V 440¥490¥22 HSF7 V
450 494 20 450¥494¥20 HSF3 R 450¥494¥20 HSF7 R

450¥494¥20 HSF3 V 450¥494¥20 HSF7 V
460 510 22 460¥510¥22 HSF3 R 460¥510¥22 HSF7 R

460¥510¥22 HSF3 V 460¥510¥22 HSF7 V
480 530 22 480¥530¥22 HSF3 R 480¥530¥22 HSF7 R
480¥530¥22 HSF3 V 480¥530¥22 HSF7 V
500 544 20 500¥544¥20 HSF3 R 500¥544¥20 HSF7 R

500¥544¥20 HSF3 V 500¥544¥20 HSF7 V
515 555 20 515¥555¥20 HSF3 R 515¥555¥20 HSF7 R

515¥555¥20 HSF3 V 515¥555¥20 HSF7 V
d1 D B
mm –
520 564 20 520¥564¥20 HSF3 R 520¥564¥20 HSF7 R

520¥564¥20 HSF3 V 520¥564¥20 HSF7 V

570 22 520¥570¥22 HSF3 R
520¥570¥22 HSF3 V
520¥570¥22 HSF7 R
520¥570¥22 HSF7 V
2.21
530 580 22 530¥580¥22 HSF3 R 530¥580¥22 HSF7 R
530¥580¥22 HSF3 V 530¥580¥22 HSF7 V
540 590 22 540¥590¥22 HSF3 R 540¥590¥22 HSF7 R

540¥590¥22 HSF3 V 540¥590¥22 HSF7 V
590 25 540¥590¥25 HSF3 R 540¥590¥25 HSF7 R
540¥590¥25 HSF3 V 540¥590¥25 HSF7 V
545 596,90 19,05 545¥597¥19 HSF3 R 545¥597¥19 HSF7 R

545¥597¥19 HSF3 V 545¥597¥19 HSF7 V
550 600 22 550¥600¥22 HSF3 R 550¥600¥22 HSF7 R

550¥600¥22 HSF3 V 550¥600¥22 HSF7 V
560 603 20 560¥603¥20 HSF3 R 560¥603¥20 HSF7 R

560¥603¥20 HSF3 V 560¥603¥20 HSF7 V
604 20 560¥604¥20 HSF3 R 560¥604¥20 HSF7 R
560¥604¥20 HSF3 V 560¥604¥20 HSF7 V
580 630 22 580¥630¥22 HSF3 R 580¥630¥22 HSF7 R

580¥630¥22 HSF3 V 580¥630¥22 HSF7 V
590 640 22 590¥640¥22 HSF3 R 590¥640¥22 HSF7 R

590¥640¥22 HSF3 V 590¥640¥22 HSF7 V
600 640 18 600¥640¥18 HSF3 R 600¥640¥18 HSF7 R

600¥640¥18 HSF3 V 600¥640¥18 HSF7 V
614 658 20 614¥658¥20 HSF3 R 614¥658¥20 HSF7 R

614¥658¥20 HSF3 V 614¥658¥20 HSF7 V
620 670 22 620¥670¥22 HSF3 R 620¥670¥22 HSF7 R

620¥670¥22 HSF3 V 620¥670¥22 HSF7 V
640 680 20 640¥680¥20 HSF3 R 640¥680¥20 HSF7 R

640¥680¥20 HSF3 V 640¥680¥20 HSF7 V
650 700 22 650¥700¥22 HSF3 R 650¥700¥22 HSF7 R

650¥700¥22 HSF3 V 650¥700¥22 HSF7 V
660 700 18 660¥700¥18 HSF3 R 660¥700¥18 HSF7 R

660¥700¥18 HSF3 V 660¥700¥18 HSF7 V
665 715 22 665¥715¥22 HSF3 R 665¥715¥22 HSF7 R

665¥715¥22 HSF3 V 665¥715¥22 HSF7 V
670 714 22 670¥714¥22 HSF3 R 670¥714¥22 HSF7 R

670¥714¥22 HSF3 V 670¥714¥22 HSF7 V
700 764 25 700¥764¥25 HSF3 R 700¥764¥25 HSF7 R

700¥764¥25 HSF3 V 700¥764¥25 HSF7 V
710 774 25 710¥774¥25 HSF3 R 710¥774¥25 HSF7 R

710¥774¥25 HSF3 V 710¥774¥25 HSF7 V
724 775 22 724¥775¥22 HSF3 R 724¥775¥22 HSF7 R

724¥775¥22 HSF3 V 724¥775¥22 HSF7 V
740 780 16,50 740¥780¥17 HSF3 R 740¥780¥17 HSF7 R

740¥780¥17 HSF3 V 740¥780¥17 HSF7 V
750 814 28 750¥814¥28 HSF3 R 750¥814¥28 HSF7 R

750¥814¥28 HSF3 V 750¥814¥28 HSF7 V
d1 775 – 985 mm

information.
d1 D
d1 D B
mm –
775 839 25 775¥839¥25 HSF3 R 775¥839¥25 HSF7 R

775¥839¥25 HSF3 V 775¥839¥25 HSF7 V
790 834 25 790¥834¥25 HSF3 R 790¥834¥25 HSF7 R

790¥834¥25 HSF3 V 790¥834¥25 HSF7 V
854 25 790¥854¥25 HSF3 R 790¥854¥25 HSF7 R
790¥854¥25 HSF3 V 790¥854¥25 HSF7 V
800 864 25 800¥864¥25 HSF3 R 800¥864¥25 HSF7 R

800¥864¥25 HSF3 V 800¥864¥25 HSF7 V
840 880 18 840¥880¥18 HSF3 R 840¥880¥18 HSF7 R

840¥880¥18 HSF3 V 840¥880¥18 HSF7 V
880 944 25,40 880¥944¥25.4 HSF3 R 880¥944¥25.4 HSF7 R

880¥944¥25.4 HSF3 V 880¥944¥25.4 HSF7 V
890 930 18 890¥930¥18 HSF3 R 890¥930¥18 HSF7 R

890¥930¥18 HSF3 V 890¥930¥18 HSF7 V
910 974 25 910¥974¥25 HSF3 R 910¥974¥25 HSF7 R

910¥974¥25 HSF3 V 910¥974¥25 HSF7 V
970 1 034 25 970¥1034¥25 HSF3 R 970¥1034¥25 HSF7 R

970¥1034¥25 HSF3 V 970¥1034¥25 HSF7 V
985 1 045 25 985¥1045¥25 HSF3 R 985¥1045¥25 HSF7 R

985¥1045¥25 HSF3 V 985¥1045¥25 HSF7 V
d1 8.500 – 45.500 in.

information.
d1 D
2.21
d1 D B R V R V
in./mm –
215,90 247,65 20,65
254,00 292,10 16,00
292,10 350,01 16,00
311,15 361,95 20,65
368,30 419,10 20,65
419,10 29,26
374,65 419,10 22,23
387,35 438,15 25,40
419,10 457,20 19,05
901,70 952,50 22,23
914,40 977,90 22,23
1 155,70 1 193,80 20,65
d1 75 – 660 mm

information.
d1 D
d1 D B
mm –
75 107 12,50 75¥107¥13 HSF4 R 75¥107¥13 HSF8 R

75¥107¥13 HSF4 V 75¥107¥13 HSF8 V
105 145 16 105¥145¥16 HSF4 R 105¥145¥16 HSF8 R

105¥145¥16 HSF4 V 105¥145¥16 HSF8 V
215 250 16 215¥250¥16 HSF4 R 215¥250¥16 HSF8 R

215¥250¥16 HSF4 V 215¥250¥16 HSF8 V
300 340 16 300¥340¥16 HSF4 R 300¥340¥16 HSF8 R

300¥340¥16 HSF4 V 300¥340¥16 HSF8 V
330 374 20 330¥374¥20 HSF4 R 330¥374¥20 HSF8 R

330¥374¥20 HSF4 V 330¥374¥20 HSF8 V
370 410 15 370¥410¥15 HSF4 R 370¥410¥15 HSF8 R

370¥410¥15 HSF4 V 370¥410¥15 HSF8 V
420 20 380¥420¥20 HSF4 R 380¥420¥20 HSF8 R
380¥420¥20 HSF4 V 380¥420¥20 HSF8 V
380 420 22 380¥420¥22 HSF4 R 380¥420¥22 HSF8 R

380¥420¥22 HSF4 V 380¥420¥22 HSF8 V
490 20 440¥490¥20 HSF4 R 440¥490¥20 HSF8 R
440¥490¥20 HSF4 V 440¥490¥20 HSF8 V
440 490 22 440¥490¥22 HSF4 R 440¥490¥22 HSF8 R

440¥490¥22 HSF4 V 440¥490¥22 HSF8 V
450 500 22 450¥500¥22 HSF4 R 450¥500¥22 HSF8 R

450¥500¥22 HSF4 V 450¥500¥22 HSF8 V
460 500 16 460¥500¥16 HSF4 R 460¥500¥16 HSF8 R

460¥500¥16 HSF4 V 460¥500¥16 HSF8 V
500 540 22 500¥540¥22 HSF4 R 500¥540¥22 HSF8 R

500¥540¥22 HSF4 V 500¥540¥22 HSF8 V
660 704 20 660¥704¥20 HSF4 R 660¥704¥20 HSF8 R

660¥704¥20 HSF4 V 660¥704¥20 HSF8 V
d1 38.000 in.

information.
d1 D
2.22
d1 D B R V R V
in./mm –
965,20 1 016,00 22,23
Radial shaft seals – HSF9 – metric dimensions

d1 200 – 860 mm

information.
d1 D
Shaft Bore Bore Lip material
diameter diameter depth
d1 D B R V
mm –
200 240 16,50 200¥240¥17 HSF9 R 200¥240¥17 HSF9 V
335 379 20 335¥379¥20 HSF9 R 335¥379¥20 HSF9 V
346 390 18 346¥390¥18 HSF9 R 346¥390¥18 HSF9 V
360 404 17,45 360¥404¥17 HSF9 R 360¥404¥17 HSF9 V
480 530 22 480¥530¥22 HSF9 R 480¥530¥22 HSF9 V
500 540 20 500¥540¥20 HSF9 R 500¥540¥20 HSF9 V
515 555 20 515¥555¥20 HSF9 R 515¥555¥20 HSF9 V
600 644 20 600¥644¥20 HSF9 R 600¥644¥20 HSF9 V
700 750 25 700¥750¥25 HSF9 R 700¥750¥25 HSF9 V
751 814 25,40 751¥814¥25 HSF9 R 751¥814¥25 HSF9 V
840 904 25 840¥904¥25 HSF9 R 840¥904¥25 HSF9 V
860 924 25 860¥924¥25 HSF9 R 860¥924¥25 HSF9 V
Radial shaft seals – HSF9 – inch dimensions

d1 17.875 – 25.996 in.

information.
d1 D
2.23
Shaft Bore Bore Lip material
d1 D B R V
in./mm –
17.875 19.850 0.813 HSF9 6715 R HSF9 6715 V

454,03 504,19 20,65
25.996 28.000 1.000 HSF9 7233 R HSF9 7233 V

660,30 711,20 25,40
Radial shaft seals – HS4 and HS5 – metric dimensions

d1 230 – 1 055 mm

For the full size range,
on page 215.
d1 D

Shaft Bore Bore
d1 D B
mm – – –
230 269 22 HS5 R 230¥269¥22 HS5 R
240 279 22 HS5 R 240¥279¥22 HS5 R
245 290 15 HS4 V 245¥290¥15 HS4 V
260 285,40 12,70 HS5 R 260¥285¥13 HS5 R
280 325 24 HS5 R 280¥325¥24 HS5 R
310 354 20 HS5 R 310¥354¥20 HS5 R
315 355 16 HS4 V 315¥355¥16 HS4 V
325 368 20 HS5 R 325¥368¥20 HS5 R
350 400 25,40 HS5 R 350¥400¥25 HS5 R
360 390 18 HS5 H 360¥390¥18 HS5 H
390 434 20 HS5 R 390¥434¥20 HS5 R
400 444 20 HS5 R 400¥444¥20 HS5 R

447 20 HS5 R 400¥447¥20 HS5 R
450 25 HS5 R 400¥450¥25 HS5 R
410 454 20 HS5 R 410¥454¥20 HS5 R
470 520 20,70 HS4 R 470¥520¥21 HS4 R
475 525 25 HS4 R 475¥525¥25 HS4 R
480 530 25 HS5 R 480¥530¥25 HS5 R
490 530 20,50 HS5 D 490¥530¥21 HS5 D
515 555 20 HS5 R 515¥555¥20 HS5 R
519 560 25 HS5 D 519¥560¥25 HS5 D
520 570 24 HS5 R 520¥570¥24 HS5 R

Shaft Bore Bore
d1 D B
mm – – –
525 575 20,70 HS4 R 525¥575¥21 HS4 R
530 575 20 HS5 R 530¥575¥20 HS5 R 2.24

540 584 20 HS4 R 540¥584¥20 HS4 R
700 740 20 HS5 D 700¥740¥20 HS5 D
710 760 25 HS5 D 710¥760¥25 HS5 D
712 757 20,50 HS5 D 712¥757¥21 HS5 D
778 818 20,50 HS5 D 778¥818¥21 HS5 D
780 830 22 HS5 R 780¥830¥22 HS5 R
910 966 17,86 HS5 R 910¥966¥18 HS5 R
978 1 018 18 HS5 R 978¥1018¥18 HS5 R
1 055 1 100 25 HS5 R 1055¥1100¥25 HS5 R

1 100 25 HS5 D 1055¥1100¥25 HS5 D
Radial shaft seals – HS4 and HS5 – inch dimensions

d1 6.438– 72.750 in.

on page 215.
d1 D

Shaft Bore Bore
d1 D B
in./mm – – –
6.438 7.688 0.625 HS5 R 596043

163,53 195,28 15,88
7.125 8.125 0.500 HS5 R 595761

180,98 206,38 12,70
7.188 8.640 0.625 HS5 R 595643

182,58 219,46 15,88
7.500 8.750 0.625 HS5 D 595822

190,50 222,25 15,88
7.750 8.750 0.625 HS5 D 595813

196,85 222,25 15,88
8.000 9.500 0.625 HS5 R 595404

203,20 241,30 15,88
8.625 10.125 0.609 HS5 R 595566

219,08 257,18 15,47
9.000 10.500 0.625 HS5 R 594641

228,60 266,70 15,88
10.250 12.017 0.750 HS5 R 1025435

260,35 305,23 19,05
11.250 12.750 0.625 HS5 R 1125235

285,75 323,85 15,88
11.500 13.250 0.750 HS5 R 594850

292,10 336,55 19,05
12.000 13.000 0.500 HS5 R 1200015

304,80 330,20 12,70
12.250 13.750 0.750 HS5 R 1225125

311,15 349,25 19,05
13.375 14.875 0.625 HS5 R 1338235

339,73 377,83 15,88

Shaft Bore Bore
d1 D B
in./mm – – –
13.500 15.000 0.625 HS5 D 1350235

342,90 381,00 15,88
13.985 15.500 0.625 HS4 R 526447

2.24
355,22 393,70 15,88
14.361 15.748 0.709 HS4 R 595175

364,77 400,00 18,01
15.748 17.717 0.890 HS4 R 1574443

400,00 450,01 22,61
16.000 17.000 0.500 HS4 R 1600014

406,40 431,80 12,70
20.000 22.000 0.500 HS5 R 595044

508,00 558,80 12,70
21.000 23.000 0.813 HS4 R 526719

533,40 584,20 20,65
21.750 23.250 0.625 HS5 R 593520

552,45 590,55 15,88
24.000 25.500 0.750 HS5 R 593519

609,60 647,70 19,05
25.000 27.000 0.875 HS5 R 593183

635,00 685,80 22,23
27.000 29.000 0.813 HS5 R 2700555

685,80 736,60 20,65
33.000 34.250 0.625 HS5 D 530414

838,20 869,95 15,88
53.000 54.875 0.813 HS4 R 595881

1346,20 1393,83 20,65
72.750 74.000 0.719 HS5 R 7275135

1847.85 1879.60 18.26
Radial shaft seals – HS6, HS7 and HS8 – metric dimensions

d1 145 – 460 mm

on page 215.
d1 D

Shaft Bore Bore
d1 D B
mm – – –
145 175 14 HS8 R 145¥175¥14 HS8 R
150 180 15,88 HS8 R 150¥180¥16 HS8 R
160 200 15,88 HS8 D 160¥200¥16 HS8 D
170 200 16 HS8 V 170¥200¥16 HS8 V
180 222 16 HS7 R 180¥222¥16 HS7 R
185 220 12,70 HS8 R 185¥220¥13 HS8 R
186 226 16 HS8 R 186¥226¥16 HS8 R
190 220 16 HS8 R 190¥220¥16 HS8 R

230 16 HS8 R 190¥230¥16 HS8 R
200 238 19 HS6 R 200¥238¥19 HS6 R

238,10 19,10 HS8 R 200¥238¥19 HS8 R
220 250 15 HS8 R 220¥250¥15 HS8 R

250 16 HS8 D 220¥250¥16 HS8 D
260 14,27 HS8 R 220¥260¥14 HS8 R
260 15 HS8 R 220¥260¥15 HS8 R
260 16 HS8 R 220¥260¥16 HS8 R
230 260 15 HS8 R 230¥260¥15 HS8 R
240 270 15 HS8 R 240¥270¥15 HS8 R

275 15 HS8 R 240¥275¥15 HS8 R
280 20 HS7 R 240¥280¥20 HS7 R
250 280 15 HS8 R 250¥280¥15 HS8 R

290 15,88 HS8 R 250¥290¥16 HS8 R
260 290 16 HS8 R 260¥290¥16 HS8 R

300 20 HS8 R 260¥300¥20 HS8 R
304 20 HS8 R 260¥304¥20 HS8 R
265 310 22 HS7 R 265¥310¥22 HS7 R

Shaft Bore Bore
d1 D B
mm – – –
266 310 20 HS8 R 266¥310¥20 HS8 R
270 310 20 HS8 R 270¥310¥20 HS8 R 2.25

280 310 15 HS8 R 280¥310¥15 HS8 R
310 16 HS8 R 280¥310¥16 HS8 R
320 19,05 HS8 R 280¥320¥19 HS8 R
324 20 HS8 R 280¥324¥20 HS8 R
325 22 HS8 H 280¥325¥22 HS8 H
290 330 20 HS8 R 290¥330¥20 HS8 R

335 24 HS7 R 290¥335¥24 HS7 R
300 340 20 HS8 R 300¥340¥20 HS8 R

345 22 HS7 R 300¥345¥22 HS7 R
310 340 15 HS8 V 310¥340¥15 HS8 V

340 15 HS8 R 310¥340¥15 HS8 R
350 20 HS8 D 310¥350¥20 HS8 D
320 360 20 HS8 R 320¥360¥20 HS8 R

368,10 19,05 HS6 R 320¥368¥19 HS6 R
330 380 22 HS8 H 330¥380¥22 HS8 H
340 372 18 HS8 R 340¥372¥18 HS8 R

380 20 HS8 R 340¥380¥20 HS8 R
345 390 25 HS8 R 345¥390¥25 HS8 R
350 390 18 HS8 R 350¥390¥18 HS8 R
355 393 20 HS8 R 355¥393¥20 HS8 R
360 400 18 HS8 R 360¥400¥18 HS8 R

405 25 HS8 H 360¥405¥25 HS8 H
410,80 22,26 HS8 R 360¥411¥22 HS8 R
380 418 19 HS7 R 380¥418¥19 HS7 R

418 19 HS8 R 380¥418¥19 HS8 R
420 19,05 HS8 V 380¥420¥19 HS8 V
420 20 HS8 D 380¥420¥20 HS8 D
420 20 HS7 R 380¥420¥20 HS7 R
420 20 HS8 H 380¥420¥20 HS8 H
420 20 HS8 D 380¥420¥20 HS8 D
430 20 HS8 R 380¥430¥20 HS8 R
400 440 20 HS7 R 400¥440¥20 HS7 R

444 13,50 HS8 R 400¥444¥14 HS8 R
450 25 HS8 R 400¥450¥25 HS8 R
451 22,23 HS8 R 400¥451¥22 HS8 R
410 454 19 HS8 R 410¥454¥19 HS8 R
420 460 20 HS7 R 420¥460¥20 HS7 R
430 480 22 HS8 R 430¥480¥22 HS8 R
440 480 20 HS8 R 440¥480¥20 HS8 R

480 21 HS8 H 440¥480¥21 HS8 H
450 500 25 HS8 R 450¥500¥25 HS8 R
452 503 20,65 HS8 R 452¥503¥21 HS8 R
460 510 22 HS8 R 460¥510¥22 HS8 R
Radial shaft seals – HS6, HS7 and HS8 – metric dimensions

d1 480 – 3 000 mm

on page 215.
d1 D

Shaft Bore Bore
d1 D B
mm – – –
480 530 20 HS8 R 480¥530¥20 HS8 R
490 530 20 HS8 R 490¥530¥20 HS8 R

540 25 HS8 R 490¥540¥25 HS8 R
541 20,70 HS6 R 490¥541¥21 HS6 R
500 550 25 HS8 R 500¥550¥25 HS8 R
510 548 24,50 HS8 R 510¥548¥25 HS8 R
515 555 20 HS8 R 515¥555¥20 HS8 R
519 560 25 HS8 D 519¥560¥25 HS8 D
530 576 21 HS8 R 530¥576¥21 HS8 R

580 20 HS8 R 530¥580¥20 HS8 R
580 22 HS8 R 530¥580¥22 HS8 R
580 25 HS8 R 530¥580¥25 HS8 R
550 590 20 HS8 R 550¥590¥20 HS8 R
556 610 25,40 HS7 R 556¥610¥25 HS7 R
560 604 20 HS8 R 560¥604¥20 HS8 R
590 640 25 HS8 R 590¥640¥25 HS8 R
600 640 20 HS8 R 600¥640¥20 HS8 R
615 665 24 HS8 R 615¥665¥24 HS8 R
620 670 22 HS8 D 620¥670¥22 HS8 D
625 676 19 HS8 D 625¥676¥19 HS8 D
630 670 20 HS8 R 630¥670¥20 HS8 R
650 700 20 HS8 R 650¥700¥20 HS8 R
690 730 20 HS8 R 690¥730¥20 HS8 R

Shaft Bore Bore
d1 D B
mm – – –
700 750 20 HS8 R 700¥750¥20 HS8 R

765 25 HS8 R 700¥765¥25 HS8 R
720 771,10 21 HS8 D 720¥771¥21 HS8 D

2.25
737 790 15,88 HS6 R 737¥790¥16 HS6 R
740 790 15,88 HS8 R 740¥790¥16 HS8 R

790 25 HS8 R 740¥790¥25 HS8 R
760 800 20,60 HS8 R 760¥800¥21 HS8 R

810 20,60 HS8 R 760¥810¥21 HS8 R
820 17,50 HS8 R 760¥820¥18 HS8 R
780 820 18 HS8 R 780¥820¥18 HS8 R
800 850 25,40 HS8 R 800¥850¥25 HS8 R
810 860 20,65 HS7 R 810¥860¥21 HS7 R
840 892 18 HS6 R 840¥892¥18 HS6 R
850 900 22 HS8 R 850¥900¥22 HS8 R
865 911 18 HS8 R 865¥911¥18 HS8 R
867 920 15,88 HS6 R 867¥920¥16 HS6 R
870 920 15,88 HS8 R 870¥920¥16 HS8 R
910 966 17,86 HS6 R 910¥966¥18 HS6 R
925 975 22 HS8 D 925¥975¥22 HS8 D
930 982 22,23 HS6 R 930¥982¥22 HS6 R
1 055 1 100 25 HS8 D 1055¥1100¥25 HS8 D
1 070 1 120 20 HS6 R 1070¥1120¥20 HS6 R
1 105 1 151 17,50 HS8 R 1105¥1151¥18 HS8 R
1 180 1 230 20 HS6 R 1180¥1230¥20 HS6 R

1 248 1 298 20,70 HS8 R 1248¥1298¥21 HS8 R

1 370 1 420 19,83 HS8 H 1370¥1420¥20 HS8 H

1 380 1 420 18 HS8 R 1380¥1420¥18 HS8 R

1 675 1 725 20 HS8 R 1675¥1725¥20 HS8 R
1 725 20,62 HS8 D 1675¥1725¥21 HS8 D

1 810 1 860 20 HS8 R 1810¥1860¥20 HS8 R
1 860 20,62 HS8 D 1810¥1860¥21 HS8 D

2 850 2 900 20,63 HS8 D 2850¥2900¥21 HS8 D

2 900 2 959 17,33 HS6 R 2900¥2959¥17 HS6 R

3 000 3 050 20,63 HS8 D 3000¥3050¥21 HS8 D
Radial shaft seals – HS6, HS7 and HS8 – inch dimensions

d1 5.500 – 10.250 in.

on page 215.
d1 D

Shaft Bore Bore
d1 D B
in./mm – – –
5.500 6.500 0.500 HS8 V 597548

139,70 165,10 12,70
6.000 7.250 0.625 HS8 R 592986

152,40 184,15 15,88
7.500 0.535 HS8 R 60037
190,50 13,59
6.300 7.874 0.596 HS8 D 595052

160,00 200,00 15,14
6.438 7.688 0.625 HS7 R 594760

163,53 195,28 15,88
7.000 8.000 0.500 HS8 D 70008

177,80 203,20 12,70
7.250 8.250 0.500 HS8 R 595012

184,15 209,55 12,70
8.250 0.500 HS7 R 528377
209,55 12,70
7.625 8.875 0.625 HS8 R 595207

193,68 225,43 15,88
7.750 8.750 0.500 HS8 R 529601

196,85 222,25 12,70
8.000 9.000 0.625 HS8 V 594935

203,20 228,60 15,88
9.250 0.625 HS8 R 592376
234,95 15,88
10.000 0.750 HS7 R 590326
254,00 19,05
8.250 9.500 0.625 HS7 R 592180

209,55 241,30 15,88
10.250 0.750 HS7 R 591929
260,35 19,05

Shaft Bore Bore
d1 D B
in./mm – – –
8.500 9.500 0.500 HS8 V 594745

215,90 241,30 12,70

10.000 0.625
254,00 15,88
HS8 R 594318 2.25
8.750 9.750 0.500 HS8 V 87440
222,25 247,65 12,70
10.000 0.625 HS8 R 592627
254,00 15,88
10.750 0.750 HS7 R 597553
273,05 19,05
8.938 9.938 0.625 HS7 R 595004

227,03 254,43 15,88
9.000 10.250 0.625 HS7 R 592581

228,60 260,35 15,88
10.500 0.750 HS8 R 592600
266,70 19,05
10.674 0.703 HS8 R 592779
271,12 17,86
9.250 11.250 0.625 HS7 R 593625

234,95 285,75 15,88
11.250 0.750 HS8 R 592858
285,75 19,05
9.438 10.688 0.625 HS7 R 592126

239,73 271,48 15,88
9.500 11.000 0.625 HS8 R 531331

241,30 279,40 15,88
11.500 0.625 HS8 R 597507
292,10 15,88
9.750 10.750 0.500 HS7 R 592988

247,65 273,05 12,70
11.250 0.625 HS7 R 593385
285,75 15,88
9.938 11.188 0.625 HS8 R 594753

252,43 284,18 15,88
11.438 0.750 HS8 R 592731
290,53 19,05
10.000 11.000 0.562 HS8 R 1000018

254,00 279,40 14,28
11.250 0.625 HS7 R 1000117
285,75 15,88
11.500 0.750 HS7 R 1000257
292,10 19,05
12.000 0.625 HS7 R 1000527
304,80 15,88
12.000 0.625 HS7 V 1000025
304,80 15,88
10.125 11.750 0.750 HS8 R 1012338

257,18 298,45 19,05
10.188 11.188 0.500 HS7 R 1019017

258,78 284,18 12,70
10.250 11.250 0.625 HS7 R 1025017

260,35 285,75 15,88
12.000 0.625 HS8 R 1025368
304,80 15,88

d1 10.438 – 14.000 in.

on page 215.
d1 D

Shaft Bore Bore
d1 D B
in./mm – – –
10.438 11.688 0.875 HS8 R 1043148

265,13 296,88 22,23
10.500 11.500 0.500 HS8 R 1050018

266,70 292,10 12,70
12.000 0.750 HS8 R 1050258
304,80 19,05
12.000 0.750 HS7 R 1050257
304,80 19,05
10.710 12.511 0.625 HS8 R 1071448

272,03 317,78 15,88
10.875 12.875 0.578 HS6 R 527099

276,23 327,03 14,68
11.000 12.000 0.625 HS7 R 1100027

279,40 304,80 15,88
12.500 0.750 HS8 R 1100258
317,50 19,05
12.500 0.750 HS7 R 1100257
317,50 19,05
13.000 0.750 HS8 R 1100538
330,20 19,05
11.125 12.375 0.625 HS8 R 1113118

282,58 314,33 15,88
11.250 12.750 0.750 HS7 R 1125257

285,75 323,85 19,05
11.375 12.375 0.500 HS7 R 1138017

288,93 314,33 12,70
11.422 12.922 0.750 HS7 R 1142257

290,12 328,22 19,05
11.500 12.500 0.500 HS8 R 1150018

292,10 317,50 12,70
13.000 0.750 HS8 R 1150258
330,20 19,05

Shaft Bore Bore
d1 D B
in./mm – – –
11.750 13.250 0.750 HS7 R 1175257

298,45 336,55 19,05
11.875 13.125 0.625 HS8 R 1188118

2.25
301,63 333,38 15,88
12.000 13.000 0.500 HS8 D 1200028

304,80 330,20 12,70
13.500 0.750 HS8 R 1200258
342,90 19,05
14.000 0.813 HS8 R 1200558
355,60 20,65
12.375 13.875 0.750 HS7 R 1238257

314,33 352,43 19,05
12.500 13.500 0.500 HS8 R 1250018

317,50 342,90 12,70
14.000 0.750 HS7 R 1250257
355,60 19,05
12.625 14.125 0.750 HS7 R 1263237

320,68 358,78 19,05
12.750 14.250 0.625 HS8 R 1275238

323,85 361,95 15,88
14.250 0.750 HS7 R 1275257
361,95 19,05
13.000 14.500 0.625 HS7 R 1300237

330,20 368,30 15,88
14.500 0.750 HS8 R 1300258
368,30 19,05
15.000 0.750 HS8 R 1300548
381,00 19,05
13.125 15.125 0.750 HS8 R 592920

333,38 384,18 19,05
13.250 14.750 0.625 HS7 R 1325237

336,55 374,65 15,88
13.375 14.875 0.625 HS8 R 594057

339,73 377,83 15,88
13.500 15.000 0.750 HS8 R 1350258

342,90 381,00 19,05
15.500 0.625 HS7 R 1350527
393,70 15,88
13.750 15.250 0.750 HS7 R 1375257

349,25 387,35 19,05
13.875 15.375 0.750 HS7 R 1388257

352,43 390,53 19,05
14.000 15.000 0.500 HS8 R 1400018

355,60 381,00 12,70
15.500 0.750 HS8 R 1400258
393,70 19,05
15.500 0.750 HS7 R 1400257
393,70 19,05
15.500 0.750 HS8 V 594261
393,70 19,05
16.000 0.813 HS7 R 1400557
406,40 20,65
16.000 1.000 HS8 R 1400588
406,40 25,40

d1 14.250 – 20.000 in.

on page 215.
d1 D

Shaft Bore Bore
d1 D B
in./mm – – –
14.250 16.250 1.000 HS7 R 1425587

361,95 412,75 25,40
14.500 15.500 0.500 HS8 R 1450018

368,30 393,70 12,70
14.625 16.125 0.750 HS7 R 1463257

371,48 409,58 19,05
15.000 16.500 0.750 HS7 R 1500257

381,00 419,10 19,05
17.000 0.813 HS8 R 1500558
431,80 20,65
15.250 16.625 0.500 HS8 R 1525158

387,35 422,28 12,70
16.750 0.750 HS7 R 1525257
425,45 19,05
15.500 17.000 0.750 HS7 R 1550257

393,70 431,80 19,05
17.500 0.813 HS7 R 1550557
444,50 20,65
15.750 17.250 0.685 HS8 R 1575248

400,05 438,15 19,05
16.000 17.000 0.500 HS8 R 1600018

406,40 431,80 12,70
17.000 0.500 HS8 D 1600019
431,80 12,70
17.500 0.750 HS8 R 1600258
444,50 19,05
18.000 0.750 HS8 R 1600578
457,20 19,05
18.000 0.813 HS8 R 1600558
457,20 20,65
16.500 17.500 0.500 HS7 R 1650017

419,10 444,50 12,70
18.500 0.813 HS7 R 1650557
469,90 20,65

Shaft Bore Bore
d1 D B
in./mm – – –
16.750 18.250 0.750 HS7 R 1675257

425,45 463,55 19,05
16.875 18.375 0.500 HS7 R 1688217

2.25
428,63 466,73 12,70
17.500 19.500 1.000 HS7 R 1750587

444,50 495,30 25,40
17.716 19.716 0.813 HS7 R 1771557

449,99 500,79 20,65
17.750 19.750 0.813 HS7 R 1775557

450,85 501,65 20,65
18.000 19.000 0.500 HS8 R 1800018

457,20 482,60 12,70
19.500 0.750 HS7 R 1800257
495,30 19,05
20.000 0.813 HS8 R 1800558
508,00 20,65
18.250 19.750 0.750 HS7 R 1825257

463,55 501,65 19,05
20.250 0.813 HS7 R 1825557
514,35 20,65
18.375 20.375 0.813 HS8 R 1838558

466,73 517,53 20,65
20.500 0.875 HS8 R 1837608
520,70 22,23
18.500 20.000 0.750 HS8 D 1850248

469,90 508,00 19,05
20.500 1.000 HS7 R 1850587
520,70 25,40
18.750 20.250 0.750 HS7 R 1875257

476,25 514,35 19,05
18.937 20.937 0.813 HS7 R 1894557

481,00 531,80 20,65
19.000 20.500 0.750 HS8 R 1900258

482,60 520,70 19,05
21.000 0.813 HS7 R 1900557
533,40 20,65
19.500 21.500 0.813 HS7 R 1950557

495,30 546,10 20,65
21.500 0.813 HS8 R 1950518
546,10 20,65
19.750 21.750 0.625 HS8 R 1975528

501,65 552,45 15,88
20.000 21.500 0.625 HS8 R 2000238

508,00 546,10 15,88
21.500 0.750 HS8 R 2000258
546,10 19,05
22.000 0.625 HS7 R 2000527
558,80 15,88
22.000 1.000 HS7 R 2000587
558,80 25,40
22.125 0.916 HS8 R 2000648
561,98 23,27
22.125 0.916 HS8 D 2000649
561,98 23,27

d1 20.500 – 33.125 in.

on page 215.
d1 D

Shaft Bore Bore
d1 D B
in./mm – – –
20.500 22.500 0.875 HS8 R 2050568

520,70 571,50 22,23
20.625 22.625 0.813 HS7 R 2063557

523,88 574,68 20,65
21.000 22.580 0.578 HS8 R 2100228

533,40 573,53 14,68
23.000 0.750 HS8 R 2100518
584,20 19,05
23.000 0.813 HS8 V 594201
584,20 20,65
23.000 0.813 HS7 R 2100557
584,20 20,65
22.000 23.500 0.750 HS7 R 2200257

558,80 596,90 19,05
23.500 0.750 HS8 R 2200218
596,90 19,05
24.000 0.813 HS8 V 2200555
609,60 20,65
24.000 0.813 HS8 D 2200558
609,60 20,65
24.000 0.813 HS7 R 2200557
609,60 20,65
22.250 24.250 0.813 HS7 R 2225557

565,15 615,95 20,65
22.500 24.500 0.813 HS7 R 2250557

571,50 622,30 20,65
22.638 24.638 0.750 HS8 D 2263548

575,00 625,80 19,00
22.750 24.750 0.813 HS7 R 2275557

577,85 628,65 20,65
22.875 24.875 0.813 HS7 R 2288557

581,03 631,83 20,65

Shaft Bore Bore
d1 D B
in./mm – – –
23.000 25.000 0.813 HS8 R 2300558

584,20 635,00 20,65

25.000 0.813
635,00 20,65
HS8 D 2300559 2.25
23.208 25.208 0.813 HS8 R 2320558
589,48 640,28 20,65
23.750 25.750 0.813 HS8 R 2575558

603,25 654,05 20,65
24.000 25.500 0.750 HS8 R 2400258

609,60 647,70 19,05
25.500 0.750 HS7 R 2400257
647,70 19,05
26.000 1.000 HS8 D 2400598
660,40 25,40
24.500 26.000 0.750 HS7 R 2450257

622,30 660,40 19,05
25.000 26.500 0.750 HS7 D 2500247

635,00 673,10 19,05
27.000 0.813 HS7 R 2500557
685,80 20,65
26.000 28.125 0.916 HS8 R 2600648

660,40 714,38 23,27
26.375 27.627 0.625 HS8 R 2637118

669,93 701,73 15,88
27.000 29.000 0.813 HS8 R 2700558

685,80 736,60 20,65
27.500 28.750 0.625 HS7 R 2750117

698,50 730,25 15,88
28.000 30.000 0.813 HS8 R 2800558

711,20 762,00 20,65
28.875 30.875 0.813 HS7 R 2888557

733,43 784,23 20,65
29.000 31.000 0.813 HS7 V 2900556

736,60 787,40 20,65
29.750 31.750 0.813 HS8 R 2975558

755,65 806,45 20,65
30.000 31.250 0.625 HS8 R 3000118

762,00 793,75 15,88
32.000 1.000 HS8 H 3000519
812,80 25,40
30.750 31.750 0.500 HS7 R 3075017

781,05 806,45 12,70
32.375 34.375 1.000 HS8 H 3237519

822,33 873,13 25,40
32.500 34.500 0.916 HS7 R 3250577

825,50 876,30 23,27
33.125 35.125 0.813 HS8 R 3312558

841,38 892,18 20,65

d1 34.500 – 171.900 in.

on page 215.
d1 D

Shaft Bore Bore
d1 D B
in./mm – – –
34.500 36.500 0.813 HS7 R 3450557

876,30 927,10 20,65
38.000 40.000 0.813 HS7 R 3800557

965,20 1 016,00 20,65
38.500 40.500 0.813 HS7 R 3850557

977,90 1 028,70 20,65
40.250 41.750 0.750 HS8 R 4025258

1 022,35 1 060,45 19,05
48.000 50.000 0.813 HS8 R 4800518

1 219,20 1 270,00 20,65
51.000 53.000 0.813 HS8 R 5100558

1 295,40 1 346,20 20,65
53.000 54.875 0.813 HS8 R 5300488

1 346,20 1 393,83 20,65
54.000 56.000 0.813 HS7 R 5400557

1 371,60 1 422,40 20,65
58.500 60.500 0.813 HS8 R 5850518

1 485,90 1 536,70 20,65
60.250 62.313 0.750 HS8 R 531572

1 530,35 1 582,75 19,05
62.598 64.598 0.813 HS7 R 6259557

1 589,99 1 640,79 20,65
69.000 71.000 0.813 HS8 R 6900558

1 752,60 1 803,40 20,65
72.500 74.500 0.813 HS8 R 7250558

1 841,50 1 892,30 20,65
75.000 77.000 0.815 HS8 R 7500518

1 905,00 1 955,80 20,70

Shaft Bore Bore
d1 D B
in./mm – – –
76.000 78.000 0.813 HS8 R 594316

1 930,40 1 981,20 20,65
81.000 83.000 0.813 HS8 R 8100558

2.25
2 057,40 2 108,20 20,65
87.750 89.750 0.813 HS8 R 8775558

2 228,85 2 279,65 20,65
94.750 97.000 0.688 HS8 R 9475658

2 406,65 2 463,80 17,48
98.625 100.625 0.813 HS8 R 9862568

2 505,08 2 555,88 20,65
106.000 107.000 0.500 HS8 R 594926

2 692,40 2 717,80 12,70
125.000 126.250 0.625 HS8 R 595208

3 175,00 3 206,75 15,88
171.900 173.876 0.813 HS8 R 595214

4 366,26 4 416,45 20,65
www.nguyenxuong.com
Cassette seals
General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 322
Design features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 323 3

Testing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 323
Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 323
SKF Mudblock seal designs MUD5 and MUD7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 324
Cassette seals
General Fig. 1
SKF Mudblock designs for oil lubricated applications

The design of SKF Mudblock cassette seals has
been optimized to provide excellent retention of
either grease or oil and maximum protection
against liquid or solid contaminants († fig. 1).
The seals are made to order to meet the demands
of each specific application.
SKF Mudblock seals are widely used in wheel-
end applications such as the front and rear axles
of, for example: MUD1 MUD2
• tractors
• agricultural machinery
• construction equipment
• forestry equipment
• off-highway trucks
MUD4 MUD5
SKF Mudblock designs for grease lubricated applications
MUD3 MUD6
MUD7
Design features Installation

All SKF Mudblock seals are designed with an in Proper installation of SKF Mudblock seals is
tegrated wear sleeve and a rubber inside diam- important for optimal functioning of the seals.
eter, but can have any one of a number of sealing Please contact SKF for information and support
lip and auxiliary lip configurations. The elasto- regarding the design of installation tools for SKF
meric material is normally nitrile rubber, but Mudblock seals.
the seals are also available in other compounds
including fluoro rubber, hydrogenated nitrile
rubber or polyacrylate to meet the demands of
different operating conditions. For more infor-
mation, please refer to paragraph Sealing lip
materials, starting on page 30.
3
Testing
SKF conducts tests in climatic cells of the SKF
Mudblock seals at global testing facilities
in USA, Europe and Asia. The tests include both
our own tests and tests according to customer
specifications. SKF Mudblock seals are engin
eered using Finite Element Analysis (FEA) to
obtain optimum design solutions. FEA evaluates:
• stress/strain behavior of the sealing lip in

deformed condition
• lip contact forces
• lip opening pressure
• displacement of the lips
• assembly simulation of seal and sleeve
Cassette seals
SKF Mudblock seal designs SKF Mudblock seals MUD7 († fig. 3) are de-
MUD5 and MUD7 signed for use in grease lubricated applications
and provide features including:
SKF Mudblock seal designs MUD5 and MUD7
are a new generation of radial shaft sealing • half metal / half rubber outside diameter for
units, specifically developed for heavy-duty reliable seal retention in the bore as well as
applications in harsh environments and tough improved sealing performance
operating conditions. • rubber covered inside diameter for improved
SKF Mudblock seals MUD5 († fig. 2) are de- sealing performance and easy installation
signed for oil lubricated applications and provide • integrated wear sleeve
features including: • SKF patented lip design for extended bearing
service life
• half metal / half rubber outside diameter for • bumper maintaining the relative position
reliable seal retention in the bore as well as between the seal and the sleeve as well as
improved sealing performance acting as a barrier against contaminants
• spring-loaded main lip with SKF Wave lip • auxiliary radial lips for contaminant exclusion
design for bi-directional pumping action
• axial and auxiliary radial lips for contaminant The SKF patented lip design has a special geom-
exclusion etry combining both a spring-loaded radial lip
• integrated wear sleeve, curled for a reliable and an axial lip. This design enables excess
unitized solution to facilitate installation and pressure inside the bearing chamber to pass the
prevent damage to the lips during trans lip. Thus, the bearing can run cooler, resulting in
portation, handling and installation extended service life.
• centrifugal flap for exclusion of contaminants
• bumper maintaining the relative position
between the seal and the sleeve as well as
acting as a barrier against contaminants
• rubber covered inside diameter for high
sealing ability and easy installation
Fig. 2
SKF Mudblock seal MUD5
Half metal / half rubber outside diameter
Spring
Centrifugal flap
Main lip with SKF Wave lip design 3
Bumper
Axial lip Wear sleeve curl
Auxiliary radial lips Wear sleeve
Rubber inside diameter
Fig. 3
SKF Mudblock seal MUD7
Half metal / half rubber outside diameter
Bumper
Spring
Auxiliary radial lips
Wear sleeve
SKF patented lip design
Rubber inside diameter
www.nguyenxuong.com
Wear sleeves
General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 328
SKF Speedi-Sleeve. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 329

Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 329
Size range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 329
SKF Speedi-Sleeve Gold . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 330
Test results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 330
Selecting the right size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 330
Installing SKF Speedi-Sleeve. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 331 4
Removing SKF Speedi-Sleeve. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 333
4.1 Product table: SKF Speedi-Sleeve. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 334
Wear sleeves for heavy industrial applications (LDSLV). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 356

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 356
Designs and features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 357
Using LDSLV designs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 358
Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 358
Removal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 358
4.2 Product table: LDSLV3 and LDSLV4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 360
Wear sleeves
General shafts without having to disassemble the shaft

or changing the seal dimensions, while
To seal efficiently, radial shaft seals must run offering an excellent sealing surface. Now, SKF
against a smooth, round counterface. If the has developed a patent pending new generation
counterface becomes worn, the seals will no SKF Speedi-Sleeve with features providing an
longer be able to fulfil their function, which is even further enhanced sealing system perfor-
to retain lubricant and exclude contaminants. mance. Using SKF Speedi-Sleeve, combined
Typically, the counterface becomes scored with an SKF radial shaft seal, customers will
when a contaminant particle is caught under benefit from a more consistent and increased
the sealing lip and abrades a track as the shaft durability of the sealing system. This will enable
rotates. As this continues, the seal will enable a more stable maintenance planning with im-
more particles to pass or get stuck, and seal ef- proved predictability of the system service life.
ficiency deteriorates, eventually leading to mal- SKF Speedi-Sleeve is available for shaft diam-
function of the component that the seal is meant eters up to approximately 203 mm (8 in.). For
to protect. To rectify the situation, it is necessary larger shaft diameters, SKF offers wear sleeves
to repair the shaft surface since a seal replace- for heavy industrial applications, LDSLV3 and
ment will not be sufficient. To repair the shaft, it LDSLV4 († figs. 2 and 3). See page 356 for in-
is usually necessary to disassemble the machine formation regarding LDSLV designs.
in order to either replace the shaft or grind down
the counterface until it is again within specifi
cation.
SKF Speedi-Sleeve († fig. 1) is a well-prov-
en solution to overcome problems with worn
Fig. 1 Fig. 2
SKF Speedi-Sleeve LDSLV3 wear sleeve
SKF Speedi-Sleeve most often be left intact, but in applications

where the flange will interfere with other system
This thin-walled sleeve (0,28 mm (0.011 in.)), components, it should be removed so as not to
developed by SKF, is simply pushed in position cause friction heat and wear debris. The flange
over the worn area, providing a counterface should also be removed in applications where it
surface that is optimized for radial shaft seals. may reduce the supply of lubricant to the seal.
There is no shaft disassembly or machining This would reduce the cooling effect of the lubri-
involved and costly downtime is minimized. cant, resulting in elevated underlip temperatures
Since the same sized seal as the original can be and premature ageing of the seal material.
used, there is no need to search for other seals, If the flange is to be removed, it should be cut
or keep a stock of different sizes. from the outside diameter into the radius in one
No special equipment is required since the in- location prior to installation. The flange can then
stallation tool is supplied with the sleeve. A mallet be twisted and raised up after installation and
and a pair of pliers are all that is needed for the grasped with a pair of long-nosed pliers and
installation. twisted into a coil.
Features Size range

The new generation SKF Speedi-Sleeve uses a The standard size range covers sleeves for
proprietary stainless steel material and manu- shaft diameters from 11,99 to 203,33 mm
facturing process, resulting in an optimized seal (0.472 to 8 in.). Depending on production quan- 4
counterface surface that minimizes wear on both tities, non-standard sizes can be manufactured.
sleeve and sealing lip. The proprietary material Each sleeve is designed to fit a specific shaft
provides increased strength and excellent ductil diameter range, usually above and below the
ity properties of the sleeve. Imperceptible lubri- nominal shaft diameter. This permits some flexi
cant pockets enable the lubricant to reside on the bility to accommodate variations in the actual
sleeve and thereby prevent dry running of the shaft diameter.
sealing lip that otherwise can create excessive
wear. The contact surface is wear resistant and
machined to minimize directionality (0° ±0,05)
with a finish of Ra 0,25 to 0,5 µm (10 to 20 µin.).
This is, in fact, a better counterface surface than
can often be achieved on a shaft.
SKF Speedi-Sleeve has a removable flange to
simplify installation († fig. 4). The flange can
Fig. 3 Fig. 4
LDSLV4 wear sleeve SKF Speedi-Sleeve removable flange
Removable flange
Wear sleeves
SKF Speedi-Sleeve Gold Diagram 1
The new generation of SKF Speedi-Sleeve is SKF Speedi-Sleeve wear test

also available in the Gold version, designed for Abrasive media, test stopped at 500 hours
highly abrasive applications. A thin, metallic

coating applied to the base stainless steel im- Sleeve wear [10-2 mm2]
parts a gold colour and significantly increases 100
durability. The original seal size can still be used. Variation
SKF Speedi-Sleeve Gold is particularly effective Average
in environments where there are abrasive con- 80
taminants, especially when combined with a
seal manufactured from the SKF fluoro rubber
60
material, SKF Duralife.
40
Test results
The previous and new generation of SKF
20
Speedi-Sleeve products were tested for abra-
sion resistance under both coarse and fine dust
conditions. A 500 hour contamination test 0
(† diagram 1) showed that when compared to New Previous
the previous generation sleeve, the new genera- generation SKF generation SKF
tion SKF Speedi-Sleeve reduced abrasion by Speedi-Sleeve Speedi-Sleeve
a factor of 1,5 and was still operating efficiently.
To test sealing system effectiveness, a
Diagram 2
2 000 hour life test was performed
(† diagram 2) using SKF Speedi-Sleeve Sealing lip wear test
new and previous generation products and SKF Seals made from fluoro rubber, test stopped at 2 000 hours
Wave seals made from the SKF fluoro rubber

material SKF Duralife. The test results showed Sealing lip wear [10-2 mm2]
that SKF Speedi-Sleeve new generation re- 20

duced the sealing lip wear and the variation in Variation
the wear rate by approximately 30% compared Average
to the previous generation sleeve and outper- 15
formed a chromium-plated surface by a factor
of 2. This reduction improves the sealing system
reliability as well as the predictability of the sys- 10
tem service life.
Both tests were carried out under the same
operating conditions: 5
• temperatures up to 110 °C (225 °F)

• linear shaft speeds of up to 8,6 m/s
0
(1 700 ft/min)
Chromium- New Previous
plated generation generation
In other tests, it was found that continuous surface SKF SKF
salt spray at 35 °C (95 °F) produced no trace of Speedi-Sleeve Speedi-Sleeve
corrosion even after 600 hours. This optimized
performance is made possible through the use
of the new generation of SKF Speedi-Sleeve.
Selecting the right size Fig. 5
To determine the appropriate sleeve size, it is SKF Speedi-Sleeve installations

first necessary to clean the shaft carefully. The
diameter of an undamaged section of the seal
counterface should then be measured on at
least three different planes. The arithmetical
mean of these measurements determines the
size of SKF Speedi-Sleeve. If the value lies with-
in the permissible range listed in the product ta-
ble for the shaft diameter d1, SKF Speedi-Sleeve
will have an adequate tight fit on the shaft and
will not require an adhesive.
If no suitable size is listed in the product table,
it will be necessary to rework the shaft to an ap-
propriate dimension. This also means that a new
seal size will be required. If production quan
tities are sufficient enough, SKF can provide
specially dimensioned SKF Speedi-Sleeve or
other wear sleeve solution.
4
Installing SKF Speedi-Sleeve
All SKF Speedi-Sleeve designs are installed the
same way. Although installation is simple,
it should be done carefully to achieve the best
results. As the thin-walled sleeve has an inter-
ference fit, any disturbances on the shaft sur-
face may create a similar pattern on the sleeve
surface and cause the seal to leak. Therefore,
the seal counterface surface of the shaft should
be carefully cleaned and any burrs or rough
spots filed down prior to installation. Deep wear
grooves, scratches or very rough surfaces
should be treated with a suitable powdered
metal epoxy-type filler. The sleeve must be
positioned on the shaft before the filler has
hardened.
SKF Speedi-Sleeve must not be installed over
keyways, cross holes, splines or threads since
this will result in deformation of the sleeve,
making it difficult for the seal to follow
its new counterface surface as it rotates.
SKF Speedi-Sleeve should never be heated
prior to installation. Using heat will cause the
sleeve to expand, but when it cools, it may not
contract back to its original size, resulting in a
loose fit on the shaft.
See fig. 5 for different SKF Speedi-Sleeve
installations.
Wear sleeves
Fig. 6 Installation procedure

1 Clean the seal counterface surface on the
shaft. File down any burrs or rough spots
and make sure that the sleeve will not be in-
stalled over keyways, cross holes, splines or
similar.
2 Measure the diameter on an unworn portion
of the shaft where the sleeve will be pos
itioned († fig. 6). Measure in three pos
itions and average the readings to make
sure the shaft is within recommended specifi
cations. If the average diameter is within the
range for a given sleeve size, there is suf-
ficient press fit built into the sleeve to prevent
it from sliding or spinning without using an
adhesive.
3 Determine where the sleeve must be pos
itioned to cover the worn area. Measure to
Fig. 7
the exact point, or mark directly on the sur-
face. The sleeve must be placed over the
worn area, not just bottomed or left flush
with the end of the shaft.
4 Shallow wear grooves do not require filling.
Optionally, a light layer of a non-hardening
sealant can be applied to the inside diameter
surface of the sleeve. Clean away sealant
that migrates to the shaft or sleeve outside
diameter surface.
5 If the shaft is deeply scored, fill the groove
with a powdered metal epoxy-type filler.
Install the sleeve before the filler hardens,
enabling the sleeve to wipe off any excess
filler. Clean away any remaining filler from
the sleeve outside diameter surface.
6 It should be repeated that heat should never
be used to install SKF Speedi-Sleeve.
Fig. 8
7 If the flange should be removed after instal-
lation, cut it from the outside diameter into
the radius in one location. The flange end
of the sleeve goes on the shaft first. Then,
place the installation tool over the sleeve
(† fig. 7).
8 Gently tap the centre of the installation tool
until the sleeve covers the worn shaft sur-
face († fig. 8). If the installation tool is too
short, a length of pipe or tubing with a
squared-off, burr-free end can be used.
Be sure that the inside diameter of the pipe
is the same as that of the installation tool.
Use care not to scratch the precision ground
sleeve’s outside diameter.
9 SKF Speedi-Sleeve should always be Removing SKF Speedi-Sleeve

installed so that the outside edge of the SKF Speedi-Sleeve can be removed by
sleeve is seated on the full shaft diameter. applying heat to the sleeve with an electric heat
It must not rest in or outside the chamfer blower, which will expand it enough to let it slide
area since the sharp edge will likely cut the off the shaft without causing any damage to the
sealing lip during seal installation. shaft.
10 If the flange was cut for removal, use a pair Alternatively, the sleeve can be removed in
of long-nosed pliers to grasp the flange any of the following ways, always using care not
away from the sleeve and twist it into a coil, to damage the shaft surface:
being careful not to lift the end of the sleeve
off the shaft or it will leave a jagged edge. • by relieving the press-fit tension using a small
Flange removal must be done with care to hammer to peen across the full width of the
avoid damage to the outside diameter of the sleeve
sleeve. • by using a cold chisel to cut through the
11 After the sleeve is installed, check again for sleeve
burrs that could damage the seal. • by using a pair of wire cutters starting at or
12 Lubricate the sleeve with the system medium near the flange and applying a twisting
before installing the seal. motion
13 Proceed with seal installation.
Please note that SKF Speedi-Sleeve cannot
be reused. 4
SKF Speedi-Sleeve – metric dimensions (converted from inch dimensions)

d1 11,99 – 35,99 mm
rmax 3,18 mm
D d1
B
b1
b
All sleeves listed in the product table can be manufactured as both standard and Gold version.
Shaft diameter range Nominal dimensions Designation
d1 d1 D b1 b B1)
min max ±1,6 ±0,8 ±0,8
mm mm –
11,99 12,07 11,99 15,49 5,99 8,41 47,63 99049

12,65 12,75 12,70 15,49 6,35 8,74 50,80 99050

13,89 14,00 14,00 19,05 6,35 9,93 46,51 99055

14,22 14,38 14,30 19,05 6,35 9,93 46,51 99056

14,96 15,06 15,01 19,05 5,00 8,99 47,29 99059

15,82 15,93 15,88 19,05 7,95 10,31 50,80 998102)
15,88 19,05 7,95 10,31 50,80 99062

15,90 16,00 16,00 18,24 7,95 11,13 50,80 99058

16,94 17,04 16,99 22,23 8,00 11,00 50,80 99068

17,32 17,42 17,37 22,86 7,95 11,13 50,80 99060

17,88 18,01 18,01 24,43 8,00 11,00 46,00 99082

19,00 19,10 19,05 24,00 7,95 11,13 50,80 998112)
19,05 24,00 7,95 11,13 50,80 99076

19,28 19,33 19,30 23,83 7,95 11,13 50,80 99081

19,81 19,91 19,84 23,75 7,95 11,13 50,80 99080

19,94 20,04 19,99 23,62 8,00 11,00 50,80 99078

20,62 20,70 20,65 30,18 9,53 14,30 76,20 99083

21,77 21,87 21,82 29,34 6,35 9,53 50,80 99086

21,87 22,00 22,00 30,18 6,58 9,12 47,14 99084
22,00 30,18 8,00 11,99 46,02 99085

22,17 22,28 22,23 27,79 7,95 11,13 50,80 998122)
22,23 27,79 7,95 11,13 50,80 99087

1) Possible max. distance of the rear groove from the shaft end when the installation tool supplied with the sleeve is used
2) SKF Speedi-Sleeve Gold
d1 d1 D b1 b B1)
min max ±1,6 ±0,8 ±0,8
mm mm –
23,06 23,16 23,11 30,94 7,95 11,13 46,91 998602)

23,11 30,94 7,95 11,13 46,91 99091

23,88 24,00 24,00 28,70 7,95 11,13 50,80 99092

24,54 24,64 24,61 28,70 7,95 11,13 50,80 99094
24,61 28,70 15,88 18,26 50,80 99096

24,94 25,04 24,99 33,02 7,95 11,00 50,80 998132)
24,99 33,02 7,95 11,00 50,80 99098

25,35 25,45 25,40 30,96 7,95 11,13 50,80 998142)
25,40 30,96 7,95 11,13 50,80 99868

25,88 26,01 26,01 33,35 8,00 11,99 46,05 99103

26,92 27,03 27,00 33,53 7,95 11,13 46,81 998152)
27,00 33,53 7,95 11,13 46,81 99106

27,61 27,71 27,66 35,71 7,95 11,13 15,88 99108

27,94 28,04 27,99 34,93 9,53 12,70 46,81 998663)
4.1
27,99 34,93 9,53 12,70 46,81 99111

28,52 28,63 28,58 38,10 7,95 11,13 17,48 998162)
28,58 38,10 7,95 11,13 17,48 99112
28,58 38,10 9,53 12,70 17,48 99116

29,31 29,41 29,36 34,29 9,53 12,70 17,48 998653)
29,36 34,29 9,53 12,70 17,48 99120

29,79 29,92 29,85 35,56 7,95 11,13 17,48 99122

29,95 30,07 30,00 35,56 8,00 11,00 17,48 99114

30,10 30,23 30,18 35,56 7,95 11,13 17,48 99118

30,89 31,04 30,96 39,70 7,95 11,00 15,88 99123

31,42 31,57 31,50 39,12 8,00 11,13 17,48 99141

31,67 31,83 31,75 38,10 7,95 11,13 17,48 998172)
31,75 38,10 7,95 11,13 17,48 99125

31,93 32,08 32,00 38,10 8,00 11,13 17,48 99128

32,94 33,05 32,99 40,49 15,01 18,01 25,40 99121

33,22 33,38 33,35 40,64 6,35 9,53 20,65 99129

33,27 33,43 33,35 40,49 12,70 15,88 20,65 998182)
33,35 40,49 12,70 15,88 20,65 99131

33,86 34,01 34,01 41,28 12,70 15,88 20,65 99134

34,82 34,98 34,93 41,61 7,95 11,13 20,65 99133
34,93 41,61 12,70 15,88 20,65 998192)
34,93 41,61 12,70 15,88 20,65 99138

34,93 35,08 34,93 41,61 13,00 16,00 20,65 998202)
34,93 41,61 13,00 16,00 20,65 99139

35,84 35,99 35,99 45,24 13,00 16,99 24,99 99146


d1 36,37 – 54,10 mm
rmax 3,18 mm
D d1
B
b1
b
d1 d1 D b1 b B1)
min max ±1,6 ±0,8 ±0,8
mm mm –
36,37 36,53 36,53 45,24 14,30 17,48 25,81 998212)

36,53 45,24 14,30 17,48 25,81 99143

36,45 36,60 36,53 45,24 9,53 12,70 25,81 99144

37,85 38,00 38,00 45,24 13,00 16,99 24,99 99147

38,02 38,18 38,10 45,24 9,53 12,70 25,81 998232)
38,10 45,24 9,53 12,70 25,81 99150
38,10 45,24 14,30 17,48 25,81 998222)
38,10 45,24 14,30 17,48 25,81 99149

38,61 38,76 38,68 47,22 11,13 14,30 25,81 99152

39,34 39,50 39,42 47,22 11,13 14,30 25,81 99155

39,60 39,75 39,67 47,22 14,30 17,48 25,81 998242)
39,67 47,22 14,30 17,48 25,81 99156

39,78 39,93 39,85 47,22 15,88 19,05 25,81 99159

39,85 40,01 40,01 46,99 9,91 12,93 25,40 99153

39,93 40,08 40,08 46,99 13,00 16,00 25,98 998252)
40,08 46,99 13,00 16,00 25,98 99157

40,69 40,84 40,77 49,23 12,70 16,28 25,40 99160

40,84 41,00 41,00 49,23 12,70 15,88 25,81 99163

41,20 41,35 41,28 47,63 7,95 11,13 25,81 99161
41,28 47,63 14,30 17,48 20,65 998262)
41,28 47,63 14,30 17,48 20,65 99162

41,83 42,01 41,91 53,01 11,30 14,50 21,49 99166
41,91 53,01 14,30 17,50 21,01 99169
42,01 53,01 14,30 17,50 21,01 998732)

d1 d1 D b1 b B1)
min max ±1,6 ±0,8 ±0,8
mm mm –
41,99 42,14 42,06 53,01 13,97 17,50 21,01 99165

42,77 42,93 42,88 48,41 14,30 17,48 22,23 99168

42,80 42,95 42,88 48,41 7,95 11,13 22,23 99167

42,85 43,00 43,00 48,41 12,70 15,88 21,44 99182

43,56 43,71 43,66 51,59 14,30 17,48 20,65 99171

44,09 44,25 44,17 52,40 9,53 12,70 20,65 99170

44,37 44,53 44,45 52,20 9,53 12,70 20,65 99172
44,45 52,40 13,49 15,88 22,30 99180
44,45 52,40 14,30 17,48 20,65 998272)
44,45 52,40 14,30 17,48 20,65 99174
44,45 52,40 19,05 22,23 20,65 998282)
44,45 52,40 19,05 22,23 20,65 99175

44,73 44,88 44,86 52,40 14,30 17,48 20,65 998292)

44,86 52,40 14,30 17,48 20,65 99176 4.1
44,93 45,09 45,01 53,01 14,00 16,99 20,62 998302)
45,01 53,01 14,00 16,99 20,62 99177

45,16 45,31 45,24 53,98 16,94 20,32 26,97 99179

45,95 46,10 46,05 53,09 14,30 17,48 25,40 998312)
46,05 53,09 14,30 17,48 25,40 99181

47,17 47,32 47,22 54,76 14,30 17,48 25,40 99185

47,40 47,55 47,45 55,58 22,58 26,04 25,40 99186

47,55 47,70 47,63 55,96 4,45 7,49 18,90 99190
47,63 55,96 7,49 10,54 18,90 99188
47,63 55,96 9,53 13,11 26,67 99184
47,63 55,96 14,30 17,48 25,40 998322)
47,63 55,96 14,30 17,48 25,40 99187

47,93 48,08 48,03 56,01 14,00 16,97 24,99 99189

48,49 48,64 48,56 56,36 9,53 12,70 25,40 99192

49,12 49,28 49,23 56,36 14,30 17,48 25,40 998332)
49,23 56,36 14,30 17,48 25,40 99193

49,91 50,06 50,01 56,49 14,00 16,97 34,29 99052
50,01 57,00 14,00 16,97 24,99 99196

50,22 50,37 50,29 58,75 14,30 17,88 26,67 99198
50,72 50,88 50,80 61,11 14,30 17,48 25,55 998342)

50,80 61,11 14,30 17,48 25,40 99199
50,80 61,11 22,23 25,40 25,40 998352)
50,80 61,11 22,23 25,40 25,40 99200

51,82 51,99 51,99 62,71 12,70 15,88 34,52 99878

52,25 52,40 52,40 62,71 19,84 23,83 34,93 99205

53,92 54,05 53,98 61,52 12,70 19,05 32,54 99210

53,95 54,10 53,98 61,52 19,84 23,83 34,93 998362)
53,98 61,52 19,84 23,83 34,93 99212

d1 54,91 – 74,75 mm
rmax 3,18 mm
D d1
B
b1
b
d1 d1 D b1 b B1)
min max ±1,6 ±0,8 ±0,8
mm mm –
54,91 55,07 54,99 62,00 19,99 22,99 31,75 998632)

54,99 62,00 19,99 22,99 31,75 99215

55,52 55,68 55,58 63,50 19,84 23,83 33,35 99218

55,83 56,01 56,01 64,29 12,70 15,88 33,35 99220
56,01 64,29 19,79 23,77 80,01 99224

56,57 56,72 56,64 64,29 12,70 15,88 33,35 998612)
56,64 64,29 12,70 15,88 33,35 99229
56,64 64,29 19,84 23,01 31,75 99230

56,82 56,97 56,90 65,10 19,41 22,86 31,75 99226

57,12 57,28 57,15 64,29 7,95 11,13 33,35 998382)
57,15 64,29 7,95 11,13 33,35 99227
57,15 64,29 19,84 23,83 33,35 998372)
57,15 64,29 19,84 23,83 33,35 99225

57,91 58,06 57,99 65,99 19,99 23,83 34,93 99219

58,65 58,80 58,75 68,28 19,84 23,83 34,93 99231

59,11 59,26 59,13 69,85 19,05 22,23 38,10 99233

59,92 60,07 59,99 70,74 9,40 11,43 37,36 99241
59,99 70,74 19,99 22,99 34,93 998692)
59,99 70,74 19,99 22,99 34,93 99235

60,25 60,40 60,33 69,85 15,09 19,05 34,93 99238

60,30 60,45 60,33 69,85 13,36 17,35 34,93 99240
60,33 69,85 19,84 23,83 34,93 998392)
60,33 69,85 19,84 23,83 34,93 99237

61,82 62,00 61,93 71,83 19,84 23,83 35,38 99243
62,00 71,83 12,70 15,88 36,20 99244

d1 d1 D b1 b B1)
min max ±1,6 ±0,8 ±0,8
mm mm –
61,85 62,00 61,93 71,83 12,70 15,88 36,20 99242

63,22 63,37 63,30 73,03 19,84 23,83 35,38 99249

63,42 63,58 63,50 71,63 14,10 16,51 22,61 99253

63,50 63,65 63,50 71,83 12,70 16,66 35,38 99248
63,50 71,63 19,84 23,83 34,93 998402)
63,50 71,63 19,84 23,83 34,93 99250

63,75 63,91 63,91 71,83 19,84 23,01 36,53 99251

64,92 65,07 65,00 72,39 19,99 22,99 34,93 998412)
65,00 72,39 19,99 22,99 34,93 99254

65,02 65,18 65,10 73,43 19,84 23,83 34,93 99256

65,91 66,07 65,99 75,95 19,84 23,83 31,75 99259

66,50 66,65 66,57 77,39 19,84 23,83 34,93 99261

66,57 66,73 66,68 77,39 19,84 23,01 34,93 99264
4.1

66,60 66,75 66,68 77,39 12,70 15,88 34,93 99260

66,68 66,83 66,68 77,39 19,84 23,83 34,93 998422)
66,68 77,39 19,84 23,83 34,93 99262

67,82 68,00 68,00 79,38 19,05 22,23 42,88 99266

69,27 69,42 69,34 79,38 19,84 23,01 33,35 99268

69,60 69,75 69,67 77,85 19,84 23,83 31,75 99273

69,72 69,88 69,85 79,38 19,84 23,83 31,75 998432)
69,85 79,38 19,84 23,83 31,75 99274

69,77 69,93 69,85 78,11 36,53 41,28 41,28 99267

69,85 70,00 69,85 79,38 10,31 14,30 31,75 99272
69,85 79,38 19,84 23,83 31,75 998442)
69,85 79,38 19,84 23,83 31,75 99275
69,85 79,38 28,58 31,75 33,32 99269

69,93 70,08 70,00 79,38 19,99 24,00 31,75 99276

71,35 71,50 71,45 80,98 15,09 17,48 31,75 99281

71,83 72,01 72,01 81,92 19,05 22,23 34,11 998702)
72,01 81,92 19,05 22,23 34,11 99284

72,09 72,24 72,09 81,92 12,70 16,66 31,75 998452)
72,09 81,92 12,70 16,66 31,75 99282

72,80 72,95 72,87 80,98 19,84 23,83 31,75 99286

72,97 73,13 73,03 81,76 19,84 23,83 31,75 998462)
73,03 81,76 19,84 23,83 31,75 99287

74,60 74,75 74,63 84,94 12,70 16,28 33,81 99290
74,63 84,94 19,84 23,83 33,35 998472)
74,68 84,94 19,84 23,83 33,35 99293


d1 74,93 – 98,53 mm
rmax 3,18 mm
D d1
B
b1
b
d1 d1 D b1 b B1)
min max ±1,6 ±0,8 ±0,8
mm mm –
74,93 75,08 75,01 83,13 15,09 17,53 27,51 99289

75,01 83,95 22,00 26,01 33,35 998752)
75,01 83,95 22,00 26,01 33,35 99294

75,49 75,59 75,54 82,17 20,65 25,40 31,75 99292

75,95 76,10 76,02 85,32 12,29 15,88 33,81 99291
76,02 85,32 14,30 17,48 34,93 99298
76,02 85,09 20,65 25,40 32,54 99299

76,12 76,28 76,20 82,30 20,65 23,83 34,93 99296

76,20 76,35 76,20 84,96 15,88 20,65 32,51 99048
76,20 82,17 20,65 25,40 32,54 998482)
76,20 82,17 20,65 25,40 32,54 99300

76,40 76,56 76,48 85,22 12,70 15,88 50,80 99301

77,83 78,00 78,00 88,09 19,05 22,23 52,22 99306

79,25 79,40 79,38 89,69 17,48 20,65 50,80 99311
79,38 89,69 20,65 25,40 50,80 998492)
79,38 89,69 20,65 25,40 50,80 99312

79,35 79,55 79,38 89,54 14,00 18,01 51,59 99053

79,81 80,01 80,01 89,92 19,05 22,50 34,93 99313

79,91 80,09 80,01 89,99 11,00 15,01 34,93 99317
80,01 89,99 21,01 24,00 34,93 99315

81,92 82,07 81,99 91,06 16,76 21,54 44,45 99328

82,47 82,63 82,55 91,29 20,65 25,40 34,93 99322

d1 d1 D b1 b B1)
min max ±1,6 ±0,8 ±0,8
mm mm –
82,55 82,70 82,55 90,81 15,11 18,26 34,93 998502)

82,55 90,81 15,11 18,26 34,93 99324
82,55 91,06 17,48 22,23 31,75 99326
82,55 91,06 20,65 25,40 34,93 998512)
82,55 91,06 20,65 25,40 34,93 99325

84,00 84,15 84,07 93,68 20,65 25,40 34,93 99331

84,76 85,01 84,89 93,98 16,99 21,01 35,00 99332
84,89 93,98 21,01 24,99 35,00 998722)
84,89 93,98 21,01 24,99 35,00 99333

84,79 85,01 85,01 90,93 10,13 12,67 36,35 99334

85,67 85,83 85,73 93,68 9,53 12,70 35,81 99338
85,73 93,85 20,65 25,40 34,93 99337

87,25 87,40 87,33 97,64 19,84 23,01 35,71 99339

87,80 88,00 88,00 95,28 29,21 34,27 42,50 99481

88,32 88,47 88,39 97,41 19,84 23,01 35,71 99340
4.1

88,82 88,98 88,90 97,64 15,88 20,65 34,21 99346

88,90 89,05 88,90 97,16 7,95 12,70 34,21 99347
88,90 97,64 20,65 25,40 34,21 998522)
88,90 97,64 20,65 25,40 34,21 99350

88,93 89,08 89,00 97,64 15,88 20,65 34,24 99349

89,92 90,07 89,99 101,60 11,13 13,67 46,05 99352
89,99 101,60 13,36 16,94 44,45 99353
89,99 101,60 18,03 23,01 46,05 99351
89,99 101,60 23,01 27,99 44,45 99354

90,42 90,58 90,50 99,06 20,65 25,40 44,45 99356

91,90 92,05 91,97 102,39 20,65 25,40 44,45 99360

92,02 92,18 92,08 102,24 12,70 15,88 44,45 99363
92,08 102,39 20,65 25,40 44,45 99362

93,57 93,73 93,68 102,39 7,95 11,13 22,23 99368

93,60 93,75 93,68 102,24 20,65 23,83 45,72 99365

94,67 94,82 94,74 102,01 11,91 15,09 45,72 99359
94,74 102,24 19,84 23,01 45,72 99366

94,92 95,07 95,00 102,24 21,01 24,00 45,72 99369

95,00 95,15 95,07 102,39 8,74 12,70 45,72 99374
95,07 102,49 11,91 15,09 45,72 99364

95,15 95,30 95,22 102,24 14,30 17,48 45,72 99376

95,25 95,40 95,25 102,11 17,48 22,23 45,72 998532)
95,33 102,24 8,74 12,70 45,72 99367
95,33 102,11 17,48 22,23 45,72 99372

98,25 98,40 98,32 106,30 20,65 25,40 47,63 99386

98,37 98,53 98,43 107,16 20,65 25,40 47,63 99387


d1 99,95 – 152,48 mm
rmax 3,18 mm
D d1
B
b1
b
d1 d1 D b1 b B1)
min max ±1,6 ±0,8 ±0,8
mm mm –
99,95 100,10 100,03 109,55 20,65 25,40 52,07 998542)

100,03 109,55 20,65 25,40 52,07 99393

101,55 101,75 101,60 111,13 12,70 15,88 52,48 99401
101,60 111,13 15,24 18,42 52,07 99395
101,60 111,13 16,51 19,69 34,93 99400
101,60 111,13 20,65 25,40 52,07 998552)
101,60 111,13 20,65 25,40 52,07 99399

103,89 104,09 103,99 112,73 19,99 24,00 35,99 99409

104,70 104,90 104,78 113,54 20,65 25,40 34,93 99412

104,90 105,11 105,00 113,54 19,99 23,19 35,00 99413

106,25 106,45 106,38 114,30 20,65 25,40 34,93 99418

107,34 107,54 107,54 117,09 19,84 23,01 36,53 99423

107,90 108,10 107,95 117,09 20,65 25,40 36,53 99424

109,78 110,01 110,01 124,99 11,38 14,96 32,94 99434

109,91 110,11 109,93 124,99 12,93 16,51 31,75 99435

111,00 111,20 111,13 120,65 20,65 25,40 41,91 99437

111,79 111,99 111,99 120,65 19,05 22,50 33,02 99438

112,62 112,83 112,73 122,25 25,40 29,01 33,35 99439

114,20 114,40 114,30 123,19 20,65 25,40 31,75 998562)
114,30 124,46 20,65 25,40 31,75 99450

114,88 115,09 115,01 127,00 20,65 23,83 31,75 99452

117,37 117,58 117,48 127,00 11,13 15,88 34,93 99465
117,48 128,60 25,40 31,75 34,93 99463

d1 d1 D b1 b B1)
min max ±1,6 ±0,8 ±0,8
mm mm –
119,00 119,20 119,08 128,60 20,65 25,40 34,93 99468

119,89 120,09 119,99 129,79 8,00 11,00 33,60 99471
119,99 129,79 19,99 24,99 32,00 99473

120,55 120,75 120,65 127,00 12,70 19,05 38,10 99475

121,89 122,10 122,00 131,50 19,99 24,00 32,00 99472

122,91 123,11 123,01 132,82 19,99 24,99 31,60 99484

123,72 123,93 123,83 133,35 15,88 19,05 36,53 99487

124,89 125,10 124,99 137,16 10,01 14,00 36,53 99490
124,99 137,16 26,01 32,00 36,53 99492

126,95 127,15 127,00 137,16 13,72 17,30 36,53 99501
127,00 137,16 17,48 22,23 36,53 998572)
127,00 137,16 17,48 22,23 36,53 99498
127,00 136,91 20,65 25,40 36,53 998582)

127,00 136,91 20,65 25,40 36,53 99499 4.1
127,80 128,00 128,00 135,26 29,21 34,27 40,30 99482
129,79 130,00 129,90 139,52 19,05 23,83 30,00 99494

129,97 130,18 130,00 139,52 22,00 25,30 32,51 998742)
130,18 139,52 22,00 25,30 32,51 99491

130,05 130,25 130,18 139,70 20,65 25,40 31,75 99513

133,25 133,45 133,35 141,22 20,65 25,40 31,75 99525

134,80 135,00 134,90 145,67 20,50 25,40 31,75 99533

136,42 136,63 136,53 149,23 20,65 25,40 31,75 99537

138,02 138,23 138,13 146,05 38,10 42,88 47,63 99548

138,99 139,19 139,09 149,86 14,30 19,05 31,34 99547

139,65 139,85 139,70 150,83 13,16 17,91 31,75 99550
139,70 150,83 20,65 25,40 31,75 998592)
139,70 150,83 20,65 25,40 31,75 99549

139,90 140,11 140,00 151,00 20,50 25,40 31,75 99552

142,77 142,98 142,88 157,18 22,23 25,40 46,02 99560

144,75 145,01 145,01 154,94 19,05 22,23 46,02 99571

145,44 145,64 145,64 154,94 14,30 19,05 49,23 99562

145,95 146,15 146,05 156,97 20,65 25,40 44,45 99575

149,12 149,33 149,23 157,18 25,40 31,75 33,35 998622)
149,23 157,18 25,40 31,75 33,35 99587

149,76 150,01 149,99 159,00 26,01 30,00 32,51 99595

150,72 150,93 150,83 161,93 25,40 28,58 47,63 99596

152,27 152,48 152,40 161,54 12,70 19,05 44,45 99601
152,40 161,93 25,40 31,75 44,45 99599


d1 153,87 – 203,33 mm
rmax 3,18 mm
D d1
B
b1
b
d1 d1 D b1 b B1)
min max ±1,6 ±0,8 ±0,8
mm mm –
153,87 154,13 154,00 161,93 26,01 30,00 32,99 99605

154,74 154,99 154,86 167,01 26,01 30,00 32,99 99606

157,43 157,68 157,56 168,28 20,65 27,00 44,45 99620

158,62 158,88 158,75 168,28 26,19 31,75 44,45 99625

159,74 159,99 159,99 171,45 25,40 31,75 34,93 99630

164,97 165,23 165,10 177,80 25,40 31,75 34,93 99650

169,75 170,00 169,88 182,58 31,75 38,00 44,45 99640

171,32 171,58 171,45 180,98 20,65 27,00 44,45 99675

174,75 175,01 175,01 186,99 27,99 32,00 35,00 99687

177,67 177,93 177,80 189,87 25,40 31,75 42,88 998642)
177,80 189,87 25,40 31,75 42,88 99700

179,76 180,01 180,01 190,50 32,99 38,00 44,50 99721

184,00 184,25 184,15 197,10 31,75 38,10 55,25 99725

184,73 184,99 184,86 197,10 32,00 38,00 54,99 99726

189,08 189,33 189,31 199,64 20,65 25,40 31,75 99745

190,37 190,63 190,50 200,03 20,65 25,40 31,75 99750

196,72 196,98 196,85 210,06 25,40 33,35 47,63 99775

199,87 200,13 200,03 212,73 34,52 38,10 44,45 99787

201,50 201,75 201,63 212,73 25,40 31,75 44,45 99799

203,07 203,33 203,20 212,73 25,40 31,75 44,45 99800
SKF Speedi-Sleeve – inch dimensions

d1 0.472 – 0.877 in.
rmax 0.125 in.
D d1
B
b1
b
d1 d1 D b1 b B1)
4.1
min max ±0.063 ±0.031 ±0.031
in. in. –
0.472 0.475 0.472 0.610 0.236 0.331 1.875 99049

0.498 0.502 0.500 0.610 0.250 0.344 2.000 99050

0.547 0.551 0.551 0.750 0.250 0.391 1.831 99055

0.560 0.566 0.563 0.750 0.250 0.391 1.831 99056

0.589 0.593 0.591 0.750 0.197 0.354 1.862 99059

0.623 0.627 0.625 0.750 0.313 0.406 2.000 998102)
0.625 0.750 0.313 0.406 2.000 99062

0.626 0.630 0.630 0.718 0.313 0.438 2.000 99058

0.667 0.671 0.669 0.875 0.315 0.433 2.000 99068

0.682 0.686 0.684 0.900 0.313 0.438 2.000 99060

0.704 0.709 0.709 0.962 0.315 0.433 1.811 99082

0.748 0.752 0.750 0.945 0.313 0.438 2.000 998112)
0.750 0.945 0.313 0.438 2.000 99076

0.759 0.761 0.760 0.938 0.313 0.438 2.000 99081

0.780 0.784 0.781 0.935 0.313 0.438 2.000 99080

0.785 0.789 0.787 0.930 0.315 0.433 2.000 99078

0.812 0.815 0.813 1.188 0.375 0.563 3.000 99083

0.857 0.861 0.859 1.155 0.250 0.375 2.000 99086

0.861 0.866 0.866 1.188 0.259 0.359 1.856 99084
0.866 1.188 0.315 0.472 1.812 99085

0.873 0.877 0.875 1.094 0.313 0.438 2.000 998122)
0.875 1.094 0.313 0.438 2.000 99087


d1 0.908 – 1.659 in.
rmax 0.125 in.
D d1
B
b1
b
d1 d1 D b1 b B1)
min max ±0.063 ±0.031 ±0.031
in. in. –
0.908 0.912 0.910 1.218 0.313 0.438 1.847 998602)

0.910 1.218 0.313 0.438 1.847 99091

0.940 0.945 0.945 1.130 0.313 0.438 2.000 99092

0.966 0.970 0.969 1.130 0.313 0.438 2.000 99094
0.969 1.130 0.625 0.719 2.000 99096

0.982 0.986 0.984 1.300 0.313 0.433 2.000 998132)
0.984 1.300 0.313 0.433 2.000 99098

0.998 1.002 1.000 1.219 0.313 0.438 2.000 998142)
1.000 1.219 0.313 0.438 2.000 99868

1.019 1.024 1.024 1.313 0.315 0.472 1.813 99103

1.060 1.064 1.063 1.320 0.313 0.438 1.843 998152)
1.063 1.320 0.313 0.438 1.843 99106

1.087 1.091 1.089 1.406 0.313 0.438 0.625 99108

1.100 1.104 1.102 1.375 0.375 0.500 1.843 998662)
1.102 1.375 0.375 0.500 1.843 99111

1.123 1.127 1.125 1.500 0.313 0.438 0.688 998162)
1.125 1.500 0.313 0.438 0.688 99112
1.125 1.500 0.375 0.500 0.688 99116

1.154 1.158 1.156 1.350 0.375 0.500 0.688 998652)
1.156 1.350 0.375 0.500 0.688 99120

1.173 1.178 1.175 1.400 0.313 0.438 0.688 99122

1.179 1.184 1.181 1.400 0.315 0.433 0.688 99114

1.185 1.190 1.188 1.400 0.313 0.438 0.688 99118

1.216 1.222 1.219 1.563 0.313 0.433 0.625 99123

d1 d1 D b1 b B1)
min max ±0.063 ±0.031 ±0.031
in. in. –
1.237 1.243 1.240 1.540 0.315 0.438 0.688 99141

1.247 1.253 1.250 1.500 0.313 0.438 0.688 998172)
1.250 1.500 0.313 0.438 0.688 99125

1.257 1.263 1.260 1.500 0.315 0.438 0.688 99128

1.297 1.301 1.299 1.594 0.591 0.709 1.000 99121

1.308 1.314 1.313 1.600 0.250 0.375 0.813 99129

1.310 1.316 1.313 1.594 0.500 0.625 0.813 998182)
1.313 1.594 0.500 0.625 0.813 99131

1.333 1.339 1.339 1.625 0.500 0.625 0.813 99134

1.371 1.377 1.375 1.638 0.313 0.438 0.813 99133
1.375 1.638 0.500 0.625 0.813 998192)
1.375 1.638 0.500 0.625 0.813 99138

1.375

1.381 1.375
1.375
1.638 0.512 0.630 0.813 998202)
1.638 0.512 0.630 0.813 99139
4.1

1.411 1.417 1.417 1.781 0.512 0.669 0.984 99146

1.432 1.438 1.438 1.781 0.563 0.688 1.016 998212)
1.438 1.781 0.563 0.688 1.016 99143

1.435 1.441 1.438 1.781 0.375 0.500 1.016 99144

1.490 1.496 1.496 1.781 0.512 0.669 0.984 99147

1.497 1.503 1.500 1.781 0.375 0.500 1.016 998232)
1.500 1.781 0.375 0.500 1.016 99150
1.500 1.781 0.563 0.688 1.016 998222)
1.500 1.781 0.563 0.688 1.016 99149

1.520 1.526 1.523 1.859 0.438 0.563 1.016 99152

1.549 1.555 1.552 1.859 0.438 0.563 1.016 99155

1.559 1.565 1.562 1.859 0.563 0.688 1.016 998242)
1.562 1.859 0.563 0.688 1.016 99156

1.566 1.572 1.569 1.859 0.625 0.750 1.016 99159

1.569 1.575 1.575 1.850 0.390 0.509 1.000 99153

1.572 1.578 1.578 1.850 0.512 0.630 1.023 998252)
1.578 1.850 0.512 0.630 1.023 99157

1.602 1.608 1.605 1.938 0.500 0.641 1.000 99160

1.608 1.614 1.614 1.938 0.500 0.625 1.016 99163

1.622 1.628 1.625 1.875 0.313 0.438 1.016 99161
1.625 1.875 0.563 0.688 0.813 998262)
1.625 1.875 0.563 0.688 0.813 99162

1.647 1.654 1.650 2.087 0.445 0.571 0.846 99166
1.650 2.087 0.563 0.689 0.827 99169
1.654 2.087 0.563 0.689 0.827 998732)

1.653 1.659 1.656 2.087 0.550 0.689 0.827 99165


d1 1.684 – 2.441 in.
rmax 0.125 in.
D d1
B
b1
b
d1 d1 D b1 b B1)
min max ±0.063 ±0.031 ±0.031
in. in. –
1.684 1.690 1.688 1.906 0.563 0.688 0.875 99168

1.685 1.691 1.688 1.906 0.313 0.438 0.875 99167

1.687 1.693 1.693 1.906 0.500 0.625 0.844 99182

1.715 1.721 1.719 2.031 0.563 0.688 0.813 99171

1.736 1.742 1.739 2.063 0.375 0.500 0.813 99170

1.747 1.753 1.750 2.055 0.375 0.500 0.813 99172
1.750 2.063 0.531 0.625 0.878 99180
1.750 2.063 0.563 0.688 0.813 998272)
1.750 2.063 0.563 0.688 0.813 99174
1.750 2.063 0.750 0.875 0.813 998282)
1.750 2.063 0.750 0.875 0.813 99175

1.761 1.767 1.766 2.063 0.563 0.688 0.813 998292)
1.766 2.063 0.563 0.688 0.813 99176

1.769 1.775 1.772 2.087 0.551 0.669 0.812 998302)
1.772 2.087 0.551 0.669 0.812 99177

1.778 1.784 1.781 2.125 0.667 0.800 1.062 99179

1.809 1.815 1.813 2.090 0.563 0.688 1.000 998312)
1.813 2.090 0.563 0.688 1.000 99181

1.857 1.863 1.859 2.156 0.563 0.688 1.000 99185

1.866 1.872 1.868 2.188 0.889 1.025 1.000 99186

1.872 1.878 1.875 2.203 0.175 0.295 0.744 99190
1.875 2.203 0.295 0.415 0.744 99188
1.875 2.203 0.375 0.516 1.050 99184
1.875 2.203 0.563 0.688 1.000 998322)
1.875 2.203 0.563 0.688 1.000 99187

d1 d1 D b1 b B1)
min max ±0.063 ±0.031 ±0.031
in. in. –
1.887 1.893 1.891 2.205 0.551 0.668 0.984 99189

1.909 1.915 1.912 2.219 0.375 0.500 1.000 99192

1.934 1.940 1.938 2.219 0.563 0.688 1.000 998332)
1.938 2.219 0.563 0.688 1.000 99193

1.965 1.971 1.969 2.244 0.551 0.668 1.350 99052
1.969 2.244 0.551 0.668 0.984 99196

1.977 1.983 1.980 2.313 0.563 0.704 1.050 99198
1.997 2.003 2.000 2.406 0.563 0.688 1.006 998342)

2.000 2.406 0.563 0.688 1.000 99199
2.000 2.406 0.875 1.000 1.000 998352)
2.000 2.406 0.875 1.000 1.000 99200

2.040 2.047 2.047 2.469 0.500 0.625 1.359 99878

2.057 2.063 2.063 2.469 0.781 0.938 1.375 99205

2.123 2.128 2.125 2.422 0.500 0.750 1.281 99210
4.1

2.124 2.130 2.125 2.422 0.781 0.938 1.375 998362)
2.125 2.422 0.781 0.938 1.375 99212

2.162 2.168 2.165 2.441 0.787 0.905 1.250 998632)
2.165 2.441 0.787 0.905 1.250 99215

2.186 2.192 2.188 2.500 0.781 0.938 1.313 99218

2.198 2.205 2.205 2.531 0.500 0.625 1.313 99220
2.205 2.531 0.779 0.936 3.150 99224

2.227 2.233 2.230 2.531 0.500 0.625 1.313 998612)
2.230 2.531 0.500 0.625 1.313 99229
2.230 2.531 0.781 0.906 1.250 99230

2.237 2.243 2.240 2.563 0.764 0.900 1.250 99226

2.249 2.255 2.250 2.531 0.313 0.438 1.313 998382)
2.250 2.531 0.313 0.438 1.313 99227
2.250 2.531 0.781 0.938 1.313 998372)
2.250 2.531 0.781 0.938 1.313 99225

2.280 2.286 2.283 2.598 0.787 0.938 1.375 99219

2.309 2.315 2.313 2.688 0.781 0.938 1.375 99231

2.327 2.333 2.328 2.750 0.750 0.875 1.500 99233

2.359 2.365 2.362 2.785 0.370 0.450 1.471 99241
2.362 2.785 0.787 0.905 1.375 998692)
2.362 2.785 0.787 0.905 1.375 99235

2.372 2.378 2.375 2.750 0.594 0.750 1.375 99238

2.374 2.380 2.375 2.750 0.526 0.683 1.375 99240
2.375 2.750 0.781 0.938 1.375 998392)
2.375 2.750 0.781 0.938 1.375 99237

2.434 2.441 2.438 2.828 0.781 0.938 1.393 99243
2.441 2.828 0.500 0.625 1.425 99244

2.435 2.441 2.438 2.828 0.500 0.625 1.425 99242

d1 2.489 – 3.256 in.
rmax 0.125 in.
D d1
B
b1
b
d1 d1 D b1 b B1)
min max ±0.063 ±0.031 ±0.031
in. in. –
2.489 2.495 2.492 2.875 0.781 0.938 1.393 99249

2.497 2.503 2.500 2.820 0.555 0.650 0.890 99253

2.500 2.506 2.500 2.828 0.500 0.656 1.393 99248
2.500 2.820 0.781 0.938 1.375 998402)
2.500 2.820 0.781 0.938 1.375 99250

2.510 2.516 2.516 2.828 0.781 0.906 1.438 99251

2.556 2.562 2.559 2.850 0.787 0.905 1.375 998412)
2.559 2.850 0.787 0.905 1.375 99254

2.560 2.566 2.563 2.891 0.781 0.938 1.375 99256

2.595 2.601 2.598 2.990 0.781 0.938 1.250 99259

2.618 2.624 2.621 3.047 0.781 0.938 1.375 99261

2.621 2.627 2.625 3.047 0.781 0.906 1.375 99264

2.622 2.628 2.625 3.047 0.500 0.625 1.375 99260

2.625 2.631 2.625 3.047 0.781 0.938 1.375 998422)
2.625 3.047 0.781 0.938 1.375 99262

2.670 2.677 2.677 3.125 0.750 0.875 1.688 99266

2.727 2.733 2.730 3.125 0.781 0.906 1.313 99268

2.740 2.746 2.743 3.065 0.781 0.938 1.250 99273

2.745 2.751 2.750 3.125 0.781 0.938 1.250 998432)
2.750 3.125 0.781 0.938 1.250 99274

2.747 2.753 2.750 3.075 1.438 1.625 1.625 99267

d1 d1 D b1 b B1)
min max ±0.063 ±0.031 ±0.031
in. in. –
2.750 2.756 2.750 3.125 0.406 0.563 1.250 99272

2.750 3.125 0.781 0.938 1.250 998442)
2.750 3.125 0.781 0.938 1.250 99275
2.750 3.125 1.125 1.250 1.312 99269

2.753 2.759 2.756 3.125 0.787 0.945 1.250 99276

2.809 2.815 2.813 3.188 0.594 0.688 1.250 99281

2.828 2.835 2.835 3.225 0.750 0.875 1.343 998702)
2.835 3.225 0.750 0.875 1.343 99284

2.838 2.844 2.838 3.225 0.500 0.656 1.250 998452)
2.838 3.225 0.500 0.656 1.250 99282

2.866 2.872 2.869 3.188 0.781 0.938 1.250 99286

2.873 2.879 2.875 3.219 0.781 0.938 1.250 998462)
2.875 3.219 0.781 0.938 1.250 99287

2.937

2.943 2.938
2.938
3.344 0.500 0.641 1.331 99290
3.344 0.781 0.938 1.313 998472)
4.1
2.940 3.344 0.781 0.938 1.313 99293

2.950 2.956 2.953 3.273 0.594 0.690 1.083 99289
2.953 3.305 0.866 1.024 1.313 998752)
2.953 3.305 0.866 1.024 1.313 99294

2.972 2.976 2.974 3.235 0.813 1.000 1.250 99292

2.990 2.996 2.993 3.359 0.484 0.625 1.331 99291
2.993 3.359 0.563 0.688 1.375 99298
2.993 3.350 0.813 1.000 1.281 99299

2.997 3.003 3.000 3.240 0.813 0.938 1.375 99296

3.000 3.006 3.000 3.345 0.625 0.813 1.280 99048
3.000 3.235 0.813 1.000 1.281 998482)
3.000 3.235 0.813 1.000 1.281 99300

3.008 3.014 3.011 3.355 0.500 0.625 2.000 99301

3.064 3.071 3.071 3.468 0.750 0.875 2.056 99306

3.120 3.126 3.125 3.531 0.688 0.813 2.000 99311
3.125 3.531 0.813 1.000 2.000 998492)
3.125 3.531 0.813 1.000 2.000 99312

3.124 3.132 3.125 3.525 0.551 0.709 2.031 99053

3.142 3.150 3.150 3.540 0.750 0.886 1.375 99313

3.146 3.153 3.150 3.543 0.433 0.591 1.375 99317
3.150 3.543 0.827 0.945 1.375 99315

3.225 3.231 3.228 3.585 0.660 0.848 1.750 99328

3.247 3.253 3.250 3.594 0.813 1.000 1.375 99322

3.250 3.256 3.250 3.575 0.595 0.719 1.375 998502)
3.250 3.575 0.595 0.719 1.375 99324
3.250 3.585 0.688 0.875 1.250 99326
3.250 3.585 0.813 1.000 1.375 998512)
3.250 3.585 0.813 1.000 1.375 99325


d1 3.307 – 4.728 in.
rmax 0.125 in.
D d1
B
b1
b
d1 d1 D b1 b B1)
min max ±0.063 ±0.031 ±0.031
in. in. –
3.307 3.313 3.310 3.688 0.813 1.000 1.375 99331

3.337 3.347 3.342 3.700 0.669 0.827 1.378 99332
3.342 3.700 0.827 0.984 1.378 998722)
3.342 3.700 0.827 0.984 1.378 99333

3.338 3.347 3.347 3.580 0.399 0.499 1.431 99334

3.373 3.379 3.375 3.688 0.375 0.500 1.410 99338
3.375 3.695 0.813 1.000 1.375 99337

3.435 3.441 3.438 3.844 0.781 0.906 1.406 99339

3.457 3.465 3.465 3.751 1.150 1.349 1.673 99481

3.477 3.483 3.480 3.835 0.781 0.906 1.406 99340

3.497 3.503 3.500 3.844 0.625 0.813 1.347 99346

3.500 3.506 3.500 3.825 0.313 0.500 1.347 99347
3.500 3.844 0.813 1.000 1.347 998522)
3.500 3.844 0.813 1.000 1.347 99350

3.501 3.507 3.504 3.844 0.625 0.813 1.348 99349

3.540 3.546 3.543 4.000 0.438 0.538 1.813 99352
3.543 4.000 0.526 0.667 1.750 99353
3.543 4.000 0.710 0.906 1.813 99351
3.543 4.000 0.906 1.102 1.750 99354

3.560 3.566 3.563 3.900 0.813 1.000 1.750 99356

3.618 3.624 3.621 4.031 0.813 1.000 1.750 99360

3.623 3.629 3.625 4.025 0.500 0.625 1.750 99363
3.625 4.031 0.813 1.000 1.750 99362

3.684 3.690 3.688 4.031 0.313 0.438 0.875 99368

d1 d1 D b1 b B1)
min max ±0.063 ±0.031 ±0.031
in. in. –
3.685 3.691 3.688 4.025 0.813 0.938 1.800 99365

3.727 3.733 3.730 4.016 0.469 0.594 1.800 99359
3.730 4.025 0.781 0.906 1.800 99366

3.737 3.743 3.740 4.025 0.827 0.945 1.800 99369

3.740 3.746 3.743 4.031 0.344 0.500 1.800 99374
3.743 4.035 0.469 0.594 1.800 99364

3.746 3.752 3.749 4.025 0.563 0.688 1.800 99376

3.750 3.756 3.750 4.020 0.688 0.875 1.800 998532)
3.753 4.025 0.344 0.500 1.800 99367
3.753 4.020 0.688 0.875 1.800 99372

3.868 3.874 3.871 4.185 0.813 1.000 1.875 99386

3.873 3.879 3.875 4.219 0.813 1.000 1.875 99387

3.935

3.941 3.938
3.938
4.313 0.813 1.000 2.050 998542)
4.313 0.813 1.000 2.050 99393
4.1

3.998 4.006 4.000 4.375 0.500 0.625 2.066 99401
4.000 4.375 0.600 0.725 2.050 99395
4.000 4.375 0.650 0.775 1.375 99400
4.000 4.375 0.813 1.000 2.050 998552)
4.000 4.375 0.813 1.000 2.050 99399

4.090 4.098 4.094 4.438 0.787 0.945 1.417 99409

4.122 4.130 4.125 4.470 0.813 1.000 1.375 99412

4.130 4.138 4.134 4.470 0.787 0.913 1.378 99413

4.183 4.191 4.188 4.500 0.813 1.000 1.375 99418

4.226 4.234 4.234 4.610 0.781 0.906 1.438 99423

4.248 4.256 4.250 4.610 0.813 1.000 1.438 99424

4.322 4.331 4.331 4.921 0.448 0.589 1.297 99434

4.327 4.335 4.328 4.921 0.509 0.650 1.250 99435

4.370 4.378 4.375 4.750 0.813 1.000 1.650 99437

4.401 4.409 4.409 4.750 0.750 0.886 1.300 99438

4.434 4.442 4.438 4.813 1.000 1.142 1.313 99439

4.496 4.504 4.500 4.850 0.813 1.000 1.250 998562)
4.500 4.900 0.813 1.000 1.250 99450

4.523 4.531 4.528 5.000 0.813 0.938 1.250 99452

4.621 4.629 4.625 5.000 0.438 0.625 1.375 99465
4.625 5.063 1.000 1.250 1.375 99463

4.685 4.693 4.688 5.063 0.813 1.000 1.375 99468

4.720 4.728 4.724 5.110 0.315 0.433 1.323 99471
4.724 5.110 0.787 0.984 1.260 99473


d1 4.746 – 8.005 in.
rmax 0.125 in.
D d1
B
b1
b
d1 d1 D b1 b B1)
min max ±0.063 ±0.031 ±0.031
in. in. –
4.746 4.754 4.750 5.000 0.500 0.750 1.500 99475

4.799 4.807 4.803 5.177 0.787 0.945 1.260 99472

4.839 4.847 4.843 5.229 0.787 0.984 1.244 99484

4.871 4.879 4.875 5.250 0.625 0.750 1.438 99487

4.917 4.925 4.921 5.400 0.394 0.551 1.438 99490
4.921 5.400 1.024 1.260 1.438 99492

4.998 5.006 5.000 5.400 0.540 0.681 1.438 99501
5.000 5.400 0.688 0.875 1.438 998572)
5.000 5.400 0.688 0.875 1.438 99498
5.000 5.390 0.813 1.000 1.438 998582)
5.000 5.390 0.813 1.000 1.438 99499

5.032 5.039 5.039 5.325 1.150 1.349 1.587 99482

5.110 5.118 5.114 5.493 0.750 0.938 1.181 99494

5.117 5.125 5.118 5.493 0.866 0.996 1.280 998742)
5.125 5.493 0.866 0.996 1.280 99491

5.120 5.128 5.125 5.500 0.813 1.000 1.250 99513

5.246 5.254 5.250 5.560 0.813 1.000 1.250 99525

5.307 5.315 5.311 5.735 0.807 1.000 1.250 99533

5.371 5.379 5.375 5.875 0.813 1.000 1.250 99537

5.434 5.442 5.438 5.750 1.500 1.688 1.875 99548

5.472 5.480 5.476 5.900 0.563 0.750 1.234 99547

d1 d1 D b1 b B1)
min max ±0.063 ±0.031 ±0.031
in. in. –
5.498 5.506 5.500 5.938 0.518 0.705 1.250 99550

5.500 5.938 0.813 1.000 1.250 998592)
5.500 5.938 0.813 1.000 1.250 99549

5.508 5.516 5.512 5.945 0.807 1.000 1.250 99552

5.621 5.629 5.625 6.188 0.875 1.000 1.812 99560

5.699 5.709 5.709 6.100 0.750 0.875 1.812 99571

5.726 5.734 5.734 6.100 0.563 0.750 1.938 99562

5.746 5.754 5.750 6.180 0.813 1.000 1.750 99575

5.871 5.879 5.875 6.188 1.000 1.250 1.313 998622)
5.875 6.188 1.000 1.250 1.313 99587

5.896 5.906 5.905 6.260 1.024 1.181 1.280 99595

5.934 5.942 5.938 6.375 1.000 1.125 1.875 99596

5.995 6.003 6.000 6.360 0.500 0.750 1.750 99601
4.1
6.000 6.375 1.000 1.250 1.750 99599

6.058 6.068 6.063 6.375 1.024 1.181 1.299 99605

6.092 6.102 6.097 6.575 1.024 1.181 1.299 99606

6.198 6.208 6.203 6.625 0.813 1.063 1.750 99620

6.245 6.255 6.250 6.625 1.031 1.250 1.750 99625

6.289 6.299 6.299 6.750 1.000 1.250 1.375 99630

6.495 6.505 6.500 7.000 1.000 1.250 1.375 99650

6.683 6.693 6.688 7.188 1.250 1.496 1.750 99640

6.745 6.755 6.750 7.125 0.813 1.063 1.750 99675

6.880 6.890 6.890 7.362 1.102 1.260 1.378 99687

6.995 7.005 7.000 7.475 1.000 1.250 1.688 998642)
7.000 7.475 1.000 1.250 1.688 99700

7.077 7.087 7.087 7.500 1.299 1.496 1.752 99721

7.244 7.254 7.250 7.760 1.250 1.500 2.175 99725

7.273 7.283 7.278 7.760 1.260 1.496 2.165 99726

7.444 7.454 7.453 7.860 0.813 1.000 1.250 99745

7.495 7.505 7.500 7.875 0.813 1.000 1.250 99750

7.745 7.755 7.750 8.270 1.000 1.313 1.875 99775

7.869 7.879 7.875 8.375 1.359 1.500 1.750 99787

7.933 7.943 7.938 8.375 1.000 1.250 1.750 99799

7.995 8.005 8.000 8.375 1.000 1.250 1.750 99800
Wear sleeves
Wear sleeves for heavy In applications where seal wear and shaft
industrial applications damage can be expected, SKF recommends in-
stalling the sleeves before the machine is oper
(LDSLV) ational. By installing them from the outset, it
will not be necessary to rework the shaft before
General installing a replacement sleeve and the original
Outside contamination particles and polishing size can be used for the replacement seal.
friction between a rotating shaft and a seal can,
over time, result in severe shaft damage. In-
stead of repairing or replacing the damaged
shaft, SKF recommends using wear sleeves for
heavy industrial applications (LDSLV) for shaft
diameters ranging from 211,15 to 1 143 mm
(8.313 to 45 in.). The sleeves are made to order
for shaft diameters within the primary ranges
listed in tables 1 and 2. A selection of sizes is
listed in the product tables starting on page 362.
LDSLV3 and LDSLV4 are recommended for
applications where operating conditions for the
seals are difficult, particularly where solid con-
taminants can reach the seals, like in rolling
mills, primary metal plants and in chemical and
mineral plants.
Table 1 Table 2
Primary dimension range of LDSLV3 Primary dimension range of LDSLV4
Shaft range Width1) Shaft range Width1)

over incl. min max over incl. min max
mm/in. mm/in. mm/in. mm/in.
211,15 736,60 17,48 63,50 211,15 736,60 12,70 63,50

8.313 29.000 0.688 2.500 8.313 29.000 0.500 2.500
736,60 1 143,00 25,40 63,50 736,60 1 143,00 19,05 63,50

29.000 45.000 1.000 2.500 29.000 45.000 0.750 2.500
1) Total
width (b), 38,10 to 50,80 mm (1.5 to 2 in.) at 1) Total
width (b), 38,10 to 50,80 mm (1.5 to 2 in.) at
1 143,00 mm (45 in.) shaft diameter 1 143,00 mm (45 in.) shaft diameter
Contact SKF for LDSLV3 designs outside the primary size Contact SKF for LDSLV4 designs outside the primary size
range. range.
Designs and features

SKF wear sleeves for heavy industrial applications
are available in two designs: the LDSLV3 with
a flange († fig. 9) and the LDSLV4 without a
flange († fig. 10). Both designs are made of
SAE 1008 chromium-plated carbon steel to
enhance wear and corrosion resistance. Other
sleeve materials can be provided to meet the
application’s specific demands. The sleeve out-
side diameter is specially ground to provide a
precision counterface surface for the seal. The
wall thickness of the standard sleeves is
2,39 mm (0.094 in.).
LDSLV3 is designed with a flange to simplify
final positioning of the sleeve. The width of the
counterface surface for the seal is 6,35 mm
(0.25 in.) narrower than the total width of the
sleeve. The flange adds a nominal 25,4 mm
(1 in.) over the shaft diameter. The flange height
is 12,7 mm (0.5 in.) for all sizes. Note that force
should never be applied directly to the flange 4
when installing an LDSLV3.
LDSLV4 has the same features as LDSLV3 but
has no flange. LDSLV4 is intended for applications
where a flange could interfere with other com-
ponents during installation, or where a wider
seal counterface surface is required.
Fig. 9 Fig. 10
LDSLV3 LDSLV4
Wear sleeves
Using LDSLV designs Fig. 11
There are two alternative ways of using SKF Using LDSLV designs
wear sleeves for heavy industrial applications
(† fig. 11):
1 The sleeve is positioned on the shaft until it

covers the damaged part and a new seal, de-
signed for a 4,78 mm (0.188 in.) larger shaft
diameter, is used.
2 The shaft is machined down by 4,78 mm Alternative 2
(0.188 in.) in diameter, the sleeve is installed
and the original seal size is used. Original shaft
Alternative 1
The reworked shaft surface for the sleeve
should have a surface roughness between
Ra 2,5 and 3,2 µm (100 to 125 µin.).
NOTE: The shaft tolerances for LDSLV designs,

due to their heated slip-fit installation, are differ
ent from those for radial shaft seals. Contact
SKF for assistance if the sleeves are to be used
in systems with sustained temperatures higher
than 75 °C (165 °F) and surface speeds in excess
of 20 m/s (3 900 ft/min).
Installation
SKF wear sleeves for heavy industrial appli
cations are designed for a heated slip-fit instal-
lation and must therefore be uniformly heated
prior to installation. The sleeve temperature
should be approximately 180 °C (355 °F). Under
no circumstances should the sleeve be heated to
above 200 °C (390 °F). Any heating techniques
normally used for bearings are suitable, such as
induction heaters or heating cabinets.
The sleeves should be installed immediately
after heating since they cool rapidly and could
seize on the shaft before the correct position is
achieved. If repositioning is necessary, use a soft
faced hammer and a wooden block. After the
sleeve is in the desired position, check the lead-in
chamfer for any damage during installation.
Removal
The wear sleeves can be removed either by
heating them or expanding them by light hammer
blows. Prior to removal, the flange of the LDSLV3
should be cut at one point, taking care not to
damage the shaft surface.
Wear sleeves for heavy industrial applications – LDSLV3 and LDSLV4 – metric dimensions
d1 215,00 – 1 100,23 mm
d1 d1
LDSLV3 LDSLV4
Shaft Sleeve Reference Design Designation

diameter width sleeve installed
outside diameter
d1 b
mm mm mm – –
215,00 25,40 220 LDSLV3 90179

215,20 35 220 LDSLV3 87831

220,00 25 225 LDSLV3 90806
40 225 LDSLV3 87914
50,80 225 LDSLV3 87915

235,23 18 240 LDSLV4 90952

240,00 17,50 250 LDSLV3 90156

240,21 44 245 LDSLV4 87911

245,20 63,50 250 LDSLV3 90766

275,00 22 280 LDSLV4 90546

280,00 45 285 LDSLV4 90437

285,22 63,50 290 LDSLV4 90238

295,20 32 300 LDSLV3 90114

315,19 63,50 320 LDSLV4 90155

320,00 63,50 325 LDSLV4 90198

325,22 63,50 330 LDSLV4 90239

335,22 39 340 LDSLV4 90777
50 340 LDSLV4 90792

340,00 18 340 LDSLV4 87901
50 340 LDSLV4 90801
50 345 LDSLV3 90113

355,20 25,40 360 LDSLV4 90778
50 360 LDSLV4 90785

360,00 44 365 LDSLV4 87500


outside diameter
d1 b
mm mm mm – –
360,22 45 365 LDSLV4 90788

365,20 20 370 LDSLV4 87531

395,22 63,50 400 LDSLV4 87461

405,23 50 410 LDSLV4 90042

419,99 63,50 425 LDSLV3 97064

435,20 63,50 440 LDSLV4 87916
455,00 30 460 LDSLV4 90347

455,20 50 460 LDSLV4 87504

475,18 20 480 LDSLV4 87921

494,44 24 500 LDSLV4 90259

495,20 30

500 LDSLV4 87503 4.2
503,25 24 508 LDSLV4 90149

530,00 20 535 LDSLV4 87783

535,23 63 540 LDSLV4 90802

555,20 63,50 560 LDSLV4 90075

575,23 63,50 580 LDSLV4 90951

585,22 55 590 LDSLV4 90292

595,20 58,20 600 LDSLV3 90120
63,50 600 LDSLV4 89997

595,22 50 600 LDSLV3 90241

645,20 64 650 LDSLV4 90004

645,24 63,50 650 LDSLV3 87817

665,20 45 670 LDSLV4 90799

685,22 63,50 690 LDSLV4 90953

714,81 50 720 LDSLV4 87820

735,23 63 740 LDSLV4 89949

755,19 63,50 760 LDSLV3 87981

865,23 63,50 870 LDSLV4 90221

875,18 63,50 880 LDSLV4 90103

1 015,20 25 1 020 LDSLV4 90786

1 049,33 60 1 054 LDSLV4 89947

1 100,23 63 1 105 LDSLV4 89946
Wear sleeves for heavy industrial applications – LDSLV3 and LDSLV4 – inch dimensions
d1 8.313 – 10.441 in.
d1 d1
LDSLV3 LDSLV4

outside diameter
d1 b
in./mm in./mm in./mm – –
8.313 1.250 8.501 LDSLV4 85885

211,15 31,75 215,93

8.353 1.500 8.541 LDSLV4 86907
212,17 38,10 216,94

8.500 1.000 8.688 LDSLV3 85158
215,90 25,40 220,68

8.625 2.750 8.813 LDSLV3 85643
219,08 69,85 223,85

8.661 1.000 8.849 LDSLV4 87319
220,00 25,40 224,76

8.687 2.250 8.875 LDSLV3 86543
220,65 57,15 225,43

8.750 1.500 8.938 LDSLV3 87196
222,25 38,10 227,03

8.812 2.000 9.000 LDSLV4 86551
223,82 50,80 228,60

8.813 1.000 9.001 LDSLV3 85688
223,85 25,40 228,63

8.866 2.500 9.054 LDSLV4 87166
225,20 63,50 229,97

8.867 1.000 9.055 LDSLV4 87462
225,22 25,40 230,00

8.875 1.250 9.063 LDSLV3 85973
225,43 31,75 230,20
1.250 9.063 LDSLV4 87526
31,75 230,20

8.938 2.500 9.126 LDSLV4 86546
227,03 63,50 231,80


outside diameter
d1 b
9.000 1.000 9.188 LDSLV3 87555

228,60 25,40 233,38

9.055 1.000 9.243 LDSLV3 89943
230,00 25,40 234,77

9.063 1.500 9.251 LDSLV4 85931
230,20 38,10 234,98

9.125 1.000 9.313 LDSLV4 86547
231,78 25,40 236,55
1.500 9.313 LDSLV4 90130
38,10 236,55

9.250 0.875 9.438 LDSLV4 84643
234,95 22,23 239,73

9.260 1.102 9.448 LDSLV4 87789
235,20 27,99 239,98

9.313 1.500 9.501 LDSLV3
236,55 38,10 241,33
85377 4.2

9.449 1.181 9.637 LDSLV4 87144
240,00 30,00 244,78

9.500 2.500 9.688 LDSLV4 86562
241,30 63,50 246,08
1.000 9.688 LDSLV3 86633
25,40 246,08

9.563 1.000 9.751 LDSLV4 85073
242,90 25,40 247,68
2.000 9.751 LDSLV4 85397
50,80 247,68

9.750 1.438 9.938 LDSLV4 84965
247,65 36,53 252,43
2.250 9.938 LDSLV4 85045
57,15 252,43

9.813 1.125 10.001 LDSLV4 86413
249,25 28,58 254,03
2.000 10.001 LDSLV3 84156
50,80 254,03

9.835 1.575 10.023 LDSLV4 90773
249,81 40,01 254,58

10.000 1.000 10.188 LDSLV3 90070
254,00 25,40 258,78

10.063 2.250 10.251 LDSLV4 86000
255,60 57,15 260,38

10.188 1.125 10.376 LDSLV4 84962
258,78 28,58 263,55

10.240 1.970 10.424 LDSLV3 87738
260,00 50,00 264,77

10.313 2.000 10.501 LDSLV4 85629
261,95 50,80 266,73
2.250 10.501 LDSLV3 85191
57,15 266,73

10.441 2.165 10.629 LDSLV4 86798
265,20 54,99 269,98

d1 10.500 – 12.598 in.
d1 d1
LDSLV3 LDSLV4

outside diameter
d1 b
10.500 2.750 10.688 LDSLV4 86013

266,70 69,85 271,48

10.557 2.250 10.745 LDSLV4 85491
268,15 57,15 272,92

10.562 0.984 10.750 LDSLV4 90800
268,27 24,99 273,05
1.750 10.750 LDSLV4 86468
44,45 273,05
1.813 10.750 LDSLV4 86544
46,05 273,05

10.563 1.500 10.751 LDSLV4 87768
268,30 38,10 273,08

10.750 2.500 10.938 LDSLV4 86435
273,05 63,50 277,83

10.813 1.000 11.001 LDSLV3 81389
274,65 25,40 279,43
2.000 11.001 LDSLV4 85033
50,80 279,43

10.846 0.709 11.034 LDSLV4 86601
275,49 18,01 280,26

10.875 2.000 11.063 LDSLV4 84510
276,23 50,80 281,00

11.000 1.500 11.188 LDSLV4 86486
279,40 38,10 284,18
2.500 11.188 LDSLV4 86454
63,50 284,18

11.024 1.181 11.212 LDSLV4 87142
280,00 30,00 284,78

11.031 1.260 11.219 LDSLV4 87525
280,19 32,00 284,96


outside diameter
d1 b
11.062 1.750 11.250 LDSLV4 85469

280,97 44,45 285,75

11.187 1.250 11.375 LDSLV4 86269
284,15 31,75 288,93

11.188 2.250 11.376 LDSLV4 85212
284,18 57,15 288,95

11.190 2.250 11.378 LDSLV4 87566
284,23 57,15 289,00

11.313 1.500 11.501 LDSLV4 84094
287,35 38,10 292,13

11.375 2.250 11.563 LDSLV4 86145
288,93 57,15 293,70

11.417 1.750 11.605 LDSLV4 86441
290,00 44,45 294,77

11.500 0.750 11.688 LDSLV4 90761
4.2
292,10 19,05 296,88

11.562 1.000 11.750 LDSLV4 90333
293,67 25,40 298,45

11.623 1.417 11.811 LDSLV3 87875
295,22 35,99 300,00

11.750 2.375 11.938 LDSLV3 87872
298,45 60,33 303,23

11.812 1.125 12.000 LDSLV4 86687
300,02 28,58 304,80

11.813 1.500 12.001 LDSLV4 85979
300,05 38,10 304,83
2.250 12.001 LDSLV3 84819
57,15 304,83
2.750 12.001 LDSLV4 85844
69,85 304,83

11.969 0.709 12.157 LDSLV4 86600
304,00 18,00 308,79

12.000 2.250 12.188 LDSLV4 85577
304,80 57,15 309,58
2.250 12.188 LDSLV3 87406
57,15 309,58

12.063 0.625 12.251 LDSLV4 85418
306,40 15,88 311,18
2.500 12.251 LDSLV3 86404
63,50 311,18

12.312 1.500 12.500 LDSLV4 90174
312,72 38,10 317,50

12.313 0.750 12.501 LDSLV4 83760
312,75 19,05 317,53

12.500 2.125 12.688 LDSLV3 86169
317,50 53,98 322,28

12.598 0.984 12.786 LDSLV3 87434
320,00 25,00 324,76

d1 12.750 – 16.813 in.
d1 d1
LDSLV3 LDSLV4

outside diameter
d1 b
12.750 0.688 12.938 LDSLV4 87513

323,85 17,48 328,63
1.125 12.938 LDSLV3 82099
28,58 328,63
1.500 12.938 LDSLV3 90143
38,10 328,63

12.813 1.000 13.001 LDSLV4 86258
325,45 25,40 330,23
1.375 13.001 LDSLV4 84263
34,93 330,23
2.000 13.001 LDSLV3 84390
50,80 330,23
2.500 13.001 LDSLV4 86722
63,50 330,23

13.000 1.750 13.188 LDSLV4 85535
330,20 44,45 334,98

13.063 1.125 13.251 LDSLV4 84963
331,80 28,58 336,53

13.313 0.813 13.501 LDSLV4 86688
338,15 20,65 342,93
1.500 13.501 LDSLV4 87463
38,10 342,93
2.000 13.501 LDSLV3 85852
50,80 342,93

13.813 1.500 14.001 LDSLV3 81390
350,85 38,10 355,63
2.000 14.001 LDSLV4 85179
50,80 355,63

14.000 1.375 14.188 LDSLV3 89951
355,60 34,93 360,38
1.500 14.188 LDSLV3 81352
38,10 360,38

14.173 1.000 14.361 LDSLV4 87445
359,99 25,40 364,77


outside diameter
d1 b
14.313 1.500 14.501 LDSLV4 86429

363,55 38,10 368,33

14.438 2.500 14.626 LDSLV3 86403
366,73 63,50 371,50

14.500 1.000 14.688 LDSLV4 85914
368,30 25,40 373,08

14.813 1.500 15.001 LDSLV4 87723
376,25 38,10 381,03
2.125 15.001 LDSLV3 81391
53,98 381,03

15.000 1.000 15.188 LDSLV4 87247
381,00 25,40 385,78

15.062 0.750 15.250 LDSLV4 90272
382,57 19,05 387,35

15.066 1.000 15.254 LDSLV3
382,68 25,40 387,45
87871 4.2

15.188 2.500 15.376 LDSLV4 87569
385,78 63,50 390,55

15.250 0.750 15.438 LDSLV3 84964
387,35 19,05 392,13

15.560 0.906 15.748 LDSLV4 85582
395,22 23,01 400,00

15.812 2.500 16.000 LDSLV3 87634
401,62 63,50 406,40

15.813 2.000 16.001 LDSLV4 85181
401,65 50,80 406,43
2.000 16.001 LDSLV3 87446
50,80 406,43
2.500 16.001 LDSLV4 86407
63,50 406,43

15.998 2.250 16.186 LDSLV3 85908
406,35 57,15 411,12

16.000 2.000 16.188 LDSLV3 81354
406,40 50,80 411,18

16.063 0.500 16.251 LDSLV4 87613
408,00 12,70 412,78
1.250 16.251 LDSLV4 86175
31,75 412,78
1.300 16.251 LDSLV4 86426
33,02 412,78
2.000 16.251 LDSLV4 86575
50,80 412,78

16.313 2.000 16.501 LDSLV4 84697
414,35 50,80 419,13

16.750 1.500 16.938 LDSLV4 87585
425,45 38,10 430,23

16.812 1.000 17.000 LDSLV4 86737
427,02 25,40 431,80

16.813 2.250 17.001 LDSLV4 84616
427,05 57,15 431,83

d1 17.250 – 25.000 in.
d1 d1
LDSLV3 LDSLV4

outside diameter
d1 b
17.250 1.000 17.438 LDSLV4 90779

438,15 25,40 442,93
2.000 17.438 LDSLV4 84576
50,80 442,93

17.313 1.500 17.501 LDSLV4 86430
439,75 38,10 444,53

17.449 2.000 17.637 LDSLV4 85762
443,20 50,80 447,98

17.500 1.250 17.688 LDSLV4 90770
444,50 31,75 449,28

17.543 2.362 17.731 LDSLV4 86799
445,59 59,99 450,37

17.750 1.250 17.938 LDSLV4 90774
450,85 31,75 455,63
2.500 17.938 LDSLV3 86631
63,50 455,63

17.812 2.125 18.000 LDSLV4 87271
452,42 53,98 457,20

17.813 2.500 18.001 LDSLV3 86405
452,45 63,50 457,23

18.163 2.000 18.351 LDSLV4 86343
461,34 50,80 466,12

18.312 1.191 18.500 LDSLV4 90790
465,12 30,25 469,90

18.813 1.750 19.001 LDSLV4 86563
477,85 44,45 482,63
2.250 19.001 LDSLV4 87015
57,15 482,63
2.500 19.001 LDSLV4 86716
63,50 482,63


outside diameter
d1 b
19.496 2.362 19.684 LDSLV4 87631

495,20 59,99 499,97

19.497 1.575 19.685 LDSLV4 87785
495,22 40,01 500,00

19.500 1.250 19.688 LDSLV4 90769
495,30 31,75 500,08

19.563 2.750 19.751 LDSLV4 85654
496,90 69,85 501,68

19.813 1.250 20.001 LDSLV4 84781
503,25 31,75 508,03

20.312 1.000 20.500 LDSLV4 86739
515,92 25,40 520,70

20.813 1.250 21.001 LDSLV3 85800
528,65 31,75 533,43

2.125 21.001 LDSLV4
53,98 533,43
85367 4.2
2.500 21.001 LDSLV4 87298
63,50 533,43

20.865 2.250 21.053 LDSLV4 90805
529,97 57,15 534,75

20.990 2.250 21.178 LDSLV3 84579
533,15 57,15 537,92

21.000 2.250 21.188 LDSLV4 87090
533,40 57,15 538,18

21.803 2.362 21.991 LDSLV4 87069
553,80 59,99 558,57

21.813 2.250 22.001 LDSLV4 84590
554,05 57,15 558,83

22.250 1.000 22.438 LDSLV3 85691
565,15 25,40 569,93

22.303 2.362 22.491 LDSLV4 87070
566,50 59,99 571,27

22.313 1.250 22.501 LDSLV4 85907
566,75 31,75 571,53

22.812 2.000 23.000 LDSLV4 90163
579,42 50,80 584,20

23.000 2.000 23.188 LDSLV4 90146
584,20 50,80 588,98

23.434 0.984 23.622 LDSLV4 87777
595,22 24,99 600,00

23.687 1.950 23.875 LDSLV4 87907
601,65 49,53 606,43

23.812 0.750 24.000 LDSLV4 87922
604,82 19,05 609,60
2.500 24.000 LDSLV4 87960
63,50 609,60

25.000 2.500 25.188 LDSLV4 86567
635,00 63,50 639,78

d1 25.312 – 42.500 in.
d1 d1
LDSLV3 LDSLV4

outside diameter
d1 b
25.312 2.000 25.500 LDSLV4 86091

642,92 50,80 647,70

25.313 2.500 25.501 LDSLV4 87802
642,95 63,50 647,73

26.000 2.250 26.188 LDSLV3 86640
660,40 57,15 665,18

26.312 1.375 26.500 LDSLV4 90809
668,32 34,93 673,10

26.813 1.250 27.001 LDSLV4 85384
681,05 31,75 685,83
2.250 27.001 LDSLV4 85531
57,15 685,83

27.000 2.000 27.188 LDSLV4 86841
685,80 50,80 690,58

27.063 2.250 27.251 LDSLV4 84764
687,40 57,15 692,18

27.313 2.250 27.501 LDSLV4 91331
693,75 57,15 698,53

27.500 2.250 27.688 LDSLV4 84711
698,50 57,15 703,28

27.812 2.500 28.000 LDSLV4 87421
706,42 63,50 711,20

28.312 2.313 28.500 LDSLV3 87623
719,12 58,75 723,90

28.813 2.250 29.001 LDSLV4 84641
731,85 57,15 736,63

29.813 2.250 30.001 LDSLV4 84642
757,25 57,15 762,03


outside diameter
d1 b
30.000 2.500 30.188 LDSLV3 86641

762,00 63,50 766,78

30.309 1.375 30.497 LDSLV4 87530
769,85 34,93 774,62

30.312 2.500 30.500 LDSLV3 87842
769,92 63,50 774,70

30.813 2.000 31.001 LDSLV4 85039
782,65 50,80 787,43

31.812 2.500 32.000 LDSLV4 90810
808,02 63,50 812,80

32.313 2.000 32.501 LDSLV4 86090
820,75 50,80 825,53

32.812 2.220 33.000 LDSLV4 87850
833,42 56,39 838,20

33.313 2.625 33.501 LDSLV4 84730
4.2
846,15 66,68 850,93

34.312 1.750 34.500 LDSLV4 87529
871,52 44,45 876,30

35.313 2.500 35.501 LDSLV4 85814
896,95 63,50 901,73

35.812 1.500 36.000 LDSLV4 90332
909,62 38,10 914,40

36.375 2.500 36.563 LDSLV4 86111
923,93 63,50 928,70

36.813 2.500 37.001 LDSLV4 86458
935,05 63,50 939,83

37.813 1.500 38.001 LDSLV4 86973
960,45 38,10 965,23

38.000 1.500 38.188 LDSLV4 86840
965,20 38,10 969,98

38.500 1.500 38.688 LDSLV4 81753
977,90 38,10 982,68

38.813 2.125 39.001 LDSLV4 85123
985,85 53,98 990,63

39.813 2.125 40.001 LDSLV4 81826
1011,25 53,98 1016,03

41.312 1.968 41.500 LDSLV4 89948
1049,32 49,99 1054,10

42.063 2.125 42.251 LDSLV4 85038
1068,40 53,98 1073,18

42.125 2.125 42.313 LDSLV4 87054
1069,98 53,98 1074,75

42.312 1.250 42.500 LDSLV4 87379
1074,72 31,75 1079,50

42.500 1.250 42.688 LDSLV4 87392
1079,50 31,75 1084,28
www.nguyenxuong.com
Track pin seals
General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 374
Features and benefits. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 374

5.1 Product table: TP and TPM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 376
Track pin seals
General Features and benefits

The SKF track pin seals, SKF Trackstar, are spe- The basic SKF Trackstar seal design features
cifically designed for oil lubricated track chains a polyurethane sealing ring and a nitrile rubber
in off-highway applications. The seals are in- energizer († fig. 2). The sealing ring retains
stalled on the pin that connects a pair of links the oil between the pin and the bushing and ex-
in the chain († fig. 1). cludes contaminants. The energizer provides the
static sealing ability. Ribs on the seal inside diam
eter enable oil to pass to provide the necessary
lubrication.
There is also a heavy-duty version designed
with a metal reinforcement ring moulded into the
polyurethane sealing ring, providing additional
rigidity for severe operating conditions
(† fig. 3).
Both SKF Trackstar designs are installed on
a spacer ring provided by the undercarriage
manufacturer. The function of the spacer ring is
to ensure that the required space for the seal
exists when squeezed between the link and the
bushing. The spacer is designed with oil galleys
that enable oil to pass for optimal lubrication of
the main sealing lip.
Fig. 1 Fig. 2
SKF Trackstar seal installation SKF Trackstar seal design TP
Link Bushing
Rubber energizer
Pin
Spacer
ring
Polyurethane sealing ring
SKF Trackstar seals provide several important

benefits including:
• extended service life of the undercarriage

• reduced internal bushing and pin wear
• easy installation
• interchangeability with the most commonly
used sealed and lubricated track pin seals
Fig. 3
SKF Trackstar seal design TPM
Rubber energizer
Metal reinforcement ring
Polyurethane sealing ring
SKF Trackstar seals –TP and TPM – metric dimensions

d1 33,22 – 80,72 mm
B1
d2 d1 D
Spacer ring Bore Operating Lip diameter
outside diameter diameter, nominal width
d1 D B1 d2
max max
mm/in. –
33,22 47,88 ± 0,25 8,38 ± 0,25 40,01 33.2¥47.3¥11.8 TP

1.308 1.885 ± 0.010 0.330 ± 0.010 1.575

36,47 51,99 ± 0,25 8,31 ± 0,25 44,45 36.5¥51.4¥11.7 TP
1.436 2.047 ± 0.010 0.327 ± 0.010 1.750

38,05 55,04 ± 0,25 9,60 ± 0,25 46,99 38.1¥54.4¥12.8 TP
1.498 2.167 ± 0.010 0.378 ± 0.010 1.850

41,86 59,77 ± 0,25 9,25 ± 0,25 50,04 42.0¥59.1¥12.8 TP
1.648 2.353 ± 0.010 0.364 ± 0.010 1.970

42,52 59,79 ± 0,03 10,69 ± 0,25 51,05 43.1¥59.4¥14.3 TPM
1.674 2.354 ± 0.001 0.421 ± 0.010 2.010

44,60 63,04 ± 0,25 10,69 ± 0,25 53,70 44.7¥62.7¥14.2 TP
1.756 2.482 ± 0.010 0.421 ± 0.010 2.114

46,20 64,64 ± 0,15 10,80 ± 0,25 56,41 46.1¥64.1¥14.1 TP
1.819 2.545 ± 0.006 0.425 ± 0.010 2.221

45,69 62,99 ± 0,03 10,69 ± 0,25 54,71 46.3¥62.3¥14.3 TPM
1.799 2.480 ± 0.001 0.421 ± 0.010 2.154

50,29 67,59 ± 0,25 10,80 ± 0,25 58,42 50.3¥67.0¥14.7 TP
1.980 2.661 ± 0.010 0.425 ± 0.010 2.300

52,60 70,79 ± 0,25 10,80 ± 0,25 61,34 52.7¥70.5¥14.2 TP
2.071 2.787 ± 0.010 0.425 ± 0.010 2.415

52,43 70,10 ± 0,03 10,80 ± 0,25 61,11 53.0¥69.3¥14.2 TPM
2.064 2.760 ± 0.001 0.425 ± 0.010 2.406

54,99 72,75 ± 0,25 10,80 ± 0,25 64,19 54.9¥72.4¥14.8 TP
2.165 2.864 ± 0.010 0.425 ± 0.010 2.527

58,19 75,54 ± 0,25 10,67 ± 0,25 67,03 58.1¥75.0¥14.7 TP
2.291 2.974 ± 0.010 0.420 ± 0.010 2.639

58,90 77,65 ± 0,25 11,10 ± 0,25 67,59 58.8¥77.1¥15.2 TP
2.319 3.057 ± 0.010 0.437 ± 0.010 2.661

Spacer ring Bore Operating Lip diameter
outside diameter diameter, nominal width
d1 D B1 d2
max max
mm/in. –
61,09 82,55 ± 0,13 11,10 ± 0,25 70,00 61.1¥82.0¥16.0 TP

2.405 3.250 ± 0.005 0.437 ± 0.010 2.756

63,14 83,74 ± 0,25 15,49 ± 0,25 73,66 63.2¥83.1¥19.3 TP
2.486 3.297 ± 0.010 0.610 ± 0.010 2.900

63,60 83,49 ± 0,25 11,13 ± 0,25 74,22 63.6¥82.5¥15.0 TP
2.504 3.287 ± 0.010 0.438 ± 0.010 2.922

67,21 87,25 ± 0,25 11,13 ± 0,25 77,14 67.1¥86.7¥15.4 TP
2.646 3.435 ± 0.010 0.438 ± 0.010 3.037

76,71 99,80 ± 0,13 11,10 ± 0,25 89,08 76.7¥99.3¥15.1 TP
3.020 3.929 ± 0.005 0.437 ± 0.010 3.507

80,72 106,20 ± 0,13 11,10 ± 0,25 92,53 80.8¥105.8¥15.9 TP
3.178 4.181 ± 0.005 0.437 ± 0.010 3.643
5.1
www.nguyenxuong.com
Metal face seals
General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 380
Design features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 380
Lubricant requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 381
Permissible operating conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 382
Contaminants. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 382
Installing HDDF seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 382

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 382
Housing and seal preparation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 382
Installation procedure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 383
6.1 Product table: HDDF. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 384
Metal face seals
General Design features

SKF metal face seals type HDDF († fig. 1) are HDDF seals consist of two identical metal seal-
designed for use under severe service condi- ing rings and two similar Belleville washers (cup
tions at relatively low circumferential speeds. springs) made of nitrile or fluoro rubber com-
They offer reliable protection against solid and pounds, specifically developed for these seals
liquid contaminants as well as leak-proof re († fig. 3 on page 383). The sealing rings are
tention of lubricants. The seals were originally made of wear- and corrosion-resistant cast alloy
developed for off-road and tracked vehicles, but and have finely finished sliding and sealing
have been found to be equally suitable for a surfaces.
range of other applications where effective pro- The Belleville washers of nitrile or fluoro rub-
tection is required against sand, soil, mud, water ber provide the necessary uniform face loading
etc. († fig. 2). These applications include: and effective sealing at the bore and outside
diameters. The outside diameter of the washers
• all types of mixers adapts to the form of the bore in which they are
• sand treatment equipment installed. It is critical that the bore diameter and
• conveyors and other construction equipment bore depth are in accordance with the dimensions
• agricultural machinery listed in the product table on pages 384 to 387.
• washing equipment Adequate tolerances between the seal assembly
• grinding mills and other pulverizing and its mating component are critical to ensure
equipment a proper sealing performance.
• ore dressing equipment
• mining equipment
Fig. 1
HDDF seal
Lubricant requirements
A lubricant should be applied on the dynamic
sealing surfaces of a metal face seal to prevent
scoring and cover at least 30% of the sealing
surface to properly lubricate and cool the sealing
rings. The lubricant can be either a detergent
like SAE 10W-40 or a mineral based oil ranging
from 10 WT to 90 WT, depending on the ambient
temperature. It should be noted that some oils
contain additives that make them incompatible
with elastomers, which can cause degradation
of the Belleville washers, especially when exposed
to elevated temperatures.
Although mineral oils are always the recom-
mended lubricant, a grease lubricant can also
be used in some slowly rotating or oscillating
applications, where the seal face surface speed
does not exceed 0,5 m/s (100 ft/min). At higher
speeds, an oil lubricant is required, not only to
provide lubrication to the sealing faces, but also
to cool the sealing rings.
Fig. 2
HDDF application
6
Metal face seals
Permissible operating Contaminants

conditions Metal face seals are often used in heavily con-
Depending on their design, metal face seals can taminated environments, where mud packing
withstand different amounts of internal pressure. in the cavity between the housing, sealing rings
It should, however, generally be maintained and Belleville washers can occur. Eventually, the
below 0,25 MPa (35 psi). Other recommenda- mud packing can cause the Belleville washers to
tions regarding operating conditions for the be pushed out of position, resulting in improper
metal face seals, like temperature and speed, face loads or mud being pumped past the
are provided in table 1. Belleville washers.
The chemical resistance of the nitrile and Contaminants can also cause abrasion to the
fluoro rubber in general is dealt with in the Belleville washers, which in turn causes deterior
section Chemical resistance on page 35. ation of the elastomer. To minimize the risk of
seal failure due to this deterioriation, it is critical
to select a proper Belleville washer material for
the application in question.
Installing HDDF seals

General
Careful handling and installation of a metal face
seal is critical to avoid cutting or tearing of the
elastomeric Belleville washers or breaking the
metal sealing rings, both which can cause pre-
mature seal failure and immediate leakage. It
is also vital to keep the sealing faces free from
contaminants like dirt or lint. Always carefully
observe installation instructions provided on
page 383.
Table 1
Permissible operating conditions

Housing and seal preparation
Operating Recommended value
condition All housing components contacting the Belleville
washers must be free from contaminants (oil,
grease, dust, lint particles etc.) when installing
Temperature, max the seal. SKF recommends using a non-petrol
Continuous operation
Nitrile rubber (NBR) –25 to +100 °C (–15 to +210 °F) eum based solvent and a clean, lint-free wipe
Fluoro rubber (FKM) –10 to +190 °C (15 to 375 °F) to clean these components prior to installation.
Circumferential All seal parts must be handled with care to
speed, max
Continuous operation 1,8 m/s (350 ft/min)
avoid damage or scoring.
Brief periods 3,8 m/s (750 ft/min)
Pressure, max
Continuous operation 0,25 MPa (35 psi)
Brief periods 0,35 MPa (50 psi)
Installation procedure Fig. 3
1 Install the Belleville washers seated against Design features

the inside shoulder of the metal sealing rings
(† fig. 4a). Belleville washers bore
2 Carefully push each seal half (Belleville washer
and metal sealing ring) into the housing until
it is fully seated. Check that the seal is not
cocked and that the washers are seated evenly
at the bottom of the housing bore. Improper
seal installation can result in uneven face loads
around the circumference of the seal faces, shaft
causing scoring or the sealing rings to separate
and allow oil to leak.
3 Clean both metal sealing ring faces with a
lint-free wipe and apply a thin film of oil. En- metal sealing sealing
sure that no oil is applied to any surface but rings surface
the sealing ring faces († fig. 4b).

4 Check that both housings are concentric and
Fig. 4
in correct alignment. The Belleville washers
must not unseat from the bottom of the Installation procedure
housing.
5 Carefully bring the two housings together,
avoiding high impact that can scratch or break
the seal components.
6 Finally, hold one half of the assembly station-
ary while rotating the other half at least ten
complete revolutions.
NOTE: This procedure enables the installer seated seated

to check that the housing and the Belleville
washers are aligned. If the seal assembly
wobbles, it is necessary to disassemble it and
make sure that the Belleville washers are a 6
properly seated in the housing.
push
b oil lightly
Metal face seals – HDDF – inch and metric dimensions

d1 1.688 – 7.800 in.
d1 42,88 – 198,12 mm
B1
B2
B
r
3–5 mm
(100–200 µin.)
D d3 d1 D1
Designation Lip Inch dimensions

mat Shaft Bore Operating Seal inside Bore Recommended Under- Sealing Radius
erial diameter diameter width diameter depth shoulder diameter cut ring width
d1 D B1 d3 B D1 B2 b r
max min max min min max max
– – in.
16904 R 1.688 2.760 ±0.002 0.974 ±0.038 1.760 0.453 2.282 - - 0.846 0.037
18259 R 1.812 3.003 ±0.002 0.892 ±0.031 1.910 0.416 2.475 - - 0.790 0.042
21215 R 2.125 3.250 ±0.002 0.900 ±0.033 2.215 0.418 2.759 - - 0.812 0.045
25096 R 2.500 3.762 ±0.002 0.907 ±0.033 2.580 0.422 3.188 - - 0.840 0.042
27536 R 2.750 4.030 ±0.002 0.918 ±0.035 2.830 0.426 3.480 - - 0.810 0.042
30651 R 3.063 4.500 ±0.002 1.016 ±0.035 3.170 0.475 3.833 - - 0.912 0.042
35076 R 3.500 4.953 ±0.002 1.096 ±0.043 3.620 0.511 4.296 - - 0.962 0.035
38740 R 3.875 5.312 ±0.003 1.102 ±0.024 4.040 0.524 4.750 - - 1.002 0.042
38751 R 3.875 5.562 ±0.003 1.267 ±0.050 4.040 0.594 4.791 - - 1.110 0.051
43135 R 4.312 5.823 ±0.003 1.102 ±0.024 4.420 0.524 5.125 - - 1.002 0.042
43150 R 4.312 6.000 ±0.003 1.320 ±0.040 4.420 0.625 5.173 - - 1.090 0.051
46975 R 4.688 6.400 ±0.003 1.525 ±0.050 4.795 0.722 5.583 - - 1.254 0.047
50655 R 5.062 6.750 ±0.003 1.280 ±0.040 5.170 0.605 5.975 - - 1.150 0.057
54000 R 5.400 6.990 ±0.003 1.310 ±0.030 5.625 0.625 6.625 - - 1.182 0.057
56170 R 5.625 7.250 ±0.003 1.366 ±0.031 5.825 0.650 6.486 6.174 0.032 1.300 0.057
58775 R 5.875 7.641 ±0.003 1.510 ±0.031 6.000 0.724 6.868 6.548 0.056 1.490 0.073
63796 R 6.375 8.120 ±0.003 1.265 ±0.040 6.570 0.598 7.555 7.505 0.125 1.350 0.042
67560 R 6.750 8.620 ±0.004 1.375 ±0.030 6.920 0.656 7.750 - - 1.260 0.042
74310 R 7.438 9.400 ±0.004 1.656 ±0.040 7.540 0.793 8.431 - - 1.344 0.073
78020 R 7.800 10.000 ±0.004 1.750 ±0.050 7.940 0.835 8.910 - - 1.500 0.058
Designation Lip Metric dimensions

– – mm
16904 R 42,88 70,10 ±0,06 24,74 ±0,97 44,70 11,51 57,96 - - 21,49 0,94
18259 R 46,03 76,28 ±0,06 22,66 ±0,79 48,51 10,57 62,87 - - 20,07 1,07
21215 R 53,98 82,55 ±0,06 22,86 ±0,84 56,26 10,62 70,08 - - 20,62 1,14
25096 R 63,50 95,56 ±0,06 23,04 ±0,84 65,53 10,72 80,98 - - 21,34 1,07
27536 R 69,85 102,36 ±0,06 23,32 ±0,89 71,88 10,82 88,39 - - 20,57 1,07
30651 R 77,80 114,30 ±0,06 25,81 ±0,89 80,52 12,07 97,36 - - 23,16 1,07
35076 R 88,90 125,81 ±0,06 27,84 ±1,09 91,95 12,98 109,12 - - 24,43 0,89
6.1
38740 R 98,43 134,92 ±0,08 27,99 ±0,61 102,62 13,31 120,65 - - 25,45 1,07
38751 R 98,43 141,27 ±0,08 32,18 ±1,27 102,62 15,09 121,69 - - 28,19 1,30
43135 R 109,52 147,90 ±0,08 27,99 ±0,61 112,27 13,31 130,18 - - 25,45 1,07
43150 R 109,52 152,40 ±0,08 33,53 ±1,02 112,27 15,88 131,39 - - 27,69 1,30
46975 R 119,08 162,56 ±0,08 38,74 ±1,27 121,79 18,34 141,81 - - 31,85 1,19
50655 R 128,57 171,45 ±0,08 32,51 ±1,02 131,32 15,37 151,77 - - 29,21 1,45
54000 R 137,16 177,55 ±0,08 33,27 ±0,76 142,88 15,88 168,28 - - 30,02 1,45
56170 R 142,88 184,15 ±0,08 34,70 ±0,79 147,96 16,51 164,74 156,82 0,81 33,02 1,45
58775 R 149,23 194,08 ±0,08 38,35 ±0,79 152,40 18,39 174,45 166,32 1,42 37,85 1,85
63796 R 161,93 206,25 ±0,08 32,13 ±1,02 166,88 15,19 191,90 190,63 3,18 34,29 1,07
67560 R 171,45 218,95 ±0,10 34,93 ±0,76 175,77 16,66 196,85 - - 32,00 1,07
74310 R 188,93 238,76 ±0,10 42,06 ±1,02 191,52 20,14 214,15 - - 34,14 1,85
78020 R 198,12 254,00 ±0,10 44,45 ±1,27 201,68 21,21 226,31 - - 38,10 1,47
Metal face seals – HDDF – inch and metric dimensions

d1 8.250 – 29.000 in.
d1 209,55 – 736,60 mm
B1
B2
B
r
3–5 mm
(100–200 µin.)
D d3 d1 D1
Designation Lip Inch dimensions

– – in.
82540 R 8.250 10.062 ±0.004 1.560 ±0.040 8.358 0.745 9.280 9.220 0.071 1.562 0.058
86850 R 8.688 10.911 ±0.005 1.924 ±0.030 8.790 0.932 9.754 - - 1.642 0.058
93115 R 9.312 11.000 ±0.005 1.437 ±0.032 9.410 0.687 10.360 10.260 0.090 1.510 0.050
93125 R 9.312 11.625 ±0.005 1.754 ±0.050 9.410 0.837 10.750 - - 1.510 0.089
95620 R 9.562 11.859 ±0.005 1.949 ±0.069 9.660 0.925 10.703 - - 1.700 0.074
108710 R 10.875 12.969 ±0.005 1.540 ±0.050 11.060 0.730 12.100 12.000 0.143 1.670 0.043
116500 R 11.625 13.250 ±0.005 1.290 ±0.030 11.780 0.615 12.780 - - 1.210 0.045
124020 R 12.400 14.375 ±0.005 1.656 ±0.050 12.500 0.788 13.530 13.470 0.060 1.610 0.057
137570 R 13.750 15.817 ±0.005 1.875 ±0.032 13.910 0.906 14.985 - - 1.670 0.089
806715 R 14.750 16.695 ±0.005 1.875 ±0.032 14.950 0.906 15.863 - - 1.670 0.062
807115 V 14.750 16.695 ±0.005 1.875 ±0.032 14.950 0.906 15.863 - - 1.670 0.062
171025 R 17.125 19.240 ±0.006 1.531 ±0.053 17.280 0.724 18.400 18.300 0.140 1.659 0.043
191022 R 19.125 21.500 ±0.006 1.640 ±0.042 19.250 0.784 20.950 20.850 0.175 1.832 0.057
238020 R 23.875 26.875 ±0.006 2.125 ±0.040 24.280 1.018 25.550 - - 1.851 0.089
807199 V 23.875 26.875 ±0.006 2.125 ±0.040 24.280 1.018 25.550 - - 1.851 0.089
807149 V 29.000 32.000 ±0.006 2.125 ±0.040 29.512 1.028 30.672 - - 1.851 0.089
Designation Lip Metric dimensions

– – mm
82540 R 209,55 255,57 ±0,10 39,62 ±1,02 212,29 18,92 235,71 234,19 1,80 39,67 1,47
86850 R 220,68 277,14 ±0,13 48,87 ±0,76 223,27 23,67 247,75 - - 41,71 1,47
93115 R 236,52 279,40 ±0,13 36,50 ±0,81 239,01 17,45 263,14 260,60 2,29 38,35 1,27
93125 R 236,52 295,28 ±0,13 44,55 ±1,27 239,01 21,26 273,05 - - 38,35 2,26
95620 R 242,87 301,22 ±0,13 49,50 ±1,75 245,36 23,50 271,86 - - 43,18 1,88
108710 R 276,23 329,41 ±0,13 39,12 ±1,27 280,92 18,54 307,34 304,80 3,63 42,42 1,09
116500 R 295,28 336,55 ±0,13 32,77 ±0,76 299,21 15,62 324,61 - - 30,73 1,14
6.1
124020 R 314,96 365,13 ±0,13 42,06 ±1,27 317,50 20,02 343,66 342,14 1,52 40,89 1,45
137570 R 349,25 401,75 ±0,13 47,63 ±0,81 353,31 23,01 380,62 - - 42,42 2,26
806715 R 374,65 424,05 ±0,13 47,63 ±0,81 379,73 23,01 402,92 - - 42,42 1,58
807115 V 374,65 424,05 ±0,13 47,63 ±0,81 379,73 23,01 402,92 - - 42,42 1,57
171025 R 434,98 488,70 ±0,15 38,89 ±1,35 438,91 18,39 467,36 464,82 3,56 42,14 1,09
191022 R 485,78 546,10 ±0,15 41,66 ±1,07 488,95 19,91 532,13 529,59 4,45 46,53 1,45
238020 R 606,43 682,63 ±0,15 53,98 ±1,02 616,71 25,86 648,97 - - 47,02 2,26
807199 V 606,43 682,63 ±0,15 53,98 ±1,02 616,71 25,86 648,97 - - 47,02 2,26
807149 V 736,60 812,80 ±0,15 53,98 ±1,02 749,60 26,11 779,07 - - 47,02 2,26
www.nguyenxuong.com
V-ring seals
General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 390
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 390
Materials . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 391
Standard designs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 392
Main V-ring functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 393
Other V-ring functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 394
Sliding velocities. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 395
Coaxiality and runout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 396
Misalignment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 396
Counterface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 397
Counterface treatment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 397
Additional counterface information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 397
Product table sorting order . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 398
Shaft requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 399
Installing V-rings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 399 7

7.1 Product table: V-ring seals dimensions, globally valid outside North American market. . . 400
7.2 Product table: V-ring seals dimensions, for North American market . . . . . . . . . . . . . . . . 432
MVR axial shaft seals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 464

General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 464
Advantages and user benefits. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 464
Design and material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 464
Temperature range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 464
Sizes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 464
Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 465
7.3 Product table: MVR1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 466
7.4 Product table: MVR2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 468
V-ring seals
General V-rings are made entirely of elastomers with-

out fabric or metal reinforcement and are there-
V-ring seals (or V-rings) are unique all-rubber fore easy to install. They can be stretched and,
seals for rotating shafts and are used in an ex- depending on size, pushed over other compon
tremely wide range of applications. The V-ring ents like flanges, pulleys or even housings. This
can be used alone to protect a wide assortment is a very valuable feature, especially when
of bearing types from contaminants. They are replacing a seal.
also often used as secondary seals to protect
primary seals in highly contaminated
environments. Features
V-rings are installed on shafts and their thin,
tapered lip seals against a counterface perpen- A V-ring consists of a seal body, a flexible, coni-
dicular to the shaft († fig. 1a). V-rings have an cal-shaped sealing lip and an integral, resilient
interference fit on the shaft, rotate with it and “hinge” († fig. 2). It is stretched and installed
act as flingers († fig. 1b). Angular misalignment directly on the shaft, where it is held in place by
of the shaft relative to the counterface can be the inherent tension of the seal body. It rotates
tolerated († fig. 1c). V-rings provide reliable with the shaft and seals axially against a sta-
sealing even if the shaft is out-of-round or tionary counterface.
rotates eccentrically († fig. 1d). The amount The counterface can be the end face of a
by which the shaft can be displaced axially is bearing, a washer, stamping, bearing housing,
governed by the permissible displacement of or even the metal case of a radial shaft seal.
the V-ring relative to its counterface. The flexible sealing lip applies contact pres-
sure against the counterface that is relatively
Fig. 1
Installed V-ring seals
aa bb cc dd
low but sufficient enough to maintain the sealing Materials

function. The light contact pressure even enables
the seal to run dry in some low-speed applica- V-rings are normally made of nitrile rubber that
tions resulting in insignificant torque drag or features good chemical resistance, resistance
heat build-up. The contact pressure varies with to wear and can be used in applications with
the fitted width. temperatures ranging from –40 to +100 °C
The flexible lip and hinge provide adequate (–40 to +210 °F). For applications with higher
sealing even in applications with considerable temperatures or where aggressive media are
end play and shaft misalignment. present, V-rings made of fluoro rubber can be
As a result of centrifugal force, the contact supplied. The permissible operating conditions
pressure of the lip decreases as speed increases. for V-rings made of nitrile or fluoro rubber are
This means that friction losses and heat are kept listed in table 2 on page 395. In the product
to a minimum, resulting in improved wear re- table under the heading Lip code, the letters
sistance and extended service life. R and V are used to identify nitrile rubber and
fluoro rubber respectively.
W ARNING:
At temperatures above 300 °C (570 °F), all
fluoro rubber compounds give off danger-
ous fumes. For additional information, refer
to page 32.
Fig. 2
V-ring design
7
Sealing lip
Seal body
Hinge
V-ring seals
Standard designs V-rings from SKF are available for the shaft
diameter ranges listed in table 1. If the shaft
SKF offers five standard V-ring designs: diameter lies in the appropriate range for two
V-rings, the larger V-ring, refering to the Seal
• VA/VR1, the most common type of V-ring, fitted with, should always be chosen († fig. 9).
has a standard cross section and straight back In addition, special sizes and designs, including
sideface. VA/VR1 is typically used to protect split versions, can be made to order. Contact
bearing arrangements in gearboxes, electric your SKF sales representative for sizes outside
motors and drives. the standard range.
• VS/VR2, that has a standard low cross section,
tapered back face and wide body, providing
a firm hold on the shaft. VS/VR2 is commonly
used in agricultural and automotive
applications.
• VL/VR3, designed with a very compact axial
cross section. VL/VR3 is commonly used in
confined spaces to enhance labyrinth seals.
• VE/VR4, designed as secondary seals for
heavy-duty applications where the primary
seal has to be protected against water and/or
solid contaminants. The design has the larg-
est cross section of any V-ring designs and
also permits the largest axial displacements.
VE/VR4 is available in the diameter range
300 to 2 010 mm (11.811 to 79.134 in.).
• VRME/VR6, a heavy-duty, large diameter
V-ring for applications with large axial dis-
placements. VRME/VR6 can be located axially
and radially on the shaft using a standard
band clamp. VRME/VR6 is primarily designed
to protect high-speed bearing arrangements
in rolling mills, paper-making and other large
machine applications. VRME/VR6 is available
on a made-to-order basis.
Table 1
Standard V-ring designs and size ranges
Design, globally outside North America VA VS VL VE VRME

Design, North America VR1 VR2 VR3 VR4 VR6
– mm (in.)
min 2,7 4,5 105 300 300

0.106 0.177 4.134 11.811 11.811
max 2 020 210 2 025 2 010 1 995
79.257 8.268 79.724 79.134 78.543
Main V-ring functions Fig. 3
V-ring used as an excluder

V-rings are suitable for both grease and oil lu-
bricated applications. For sealing grease lubri-
cated bearing arrangements and protecting
against contaminants, the V-ring should be
arranged outside the housing cover or housing
wall. Dust, water spray and other contaminants
can be excluded in this position († fig. 3). The
V-ring can also act as a grease valve, where
used grease or excess new grease can escape
between the counterface and the sealing lip
(† fig. 4). The installation of two opposing
V-rings can be used in applications where lubri-
cant retention and contaminant exclusion are of
equal importance († fig. 5).
If V-rings are used to retain oil, they should
always be located axially on the shaft on the
Fig. 4
lubricant side († fig. 6).
V-rings should not be submerged in the V-ring used as a grease valve
application medium.
Fig. 5 Fig. 6
Two opposing V-rings V-ring located axially

7
V-ring seals
Other V-ring functions Fig. 7
V-ring used as a secondary seal

V-rings can also be used as secondary seals
(† fig. 7), for example where it is necessary
to protect the sealing lip and counterface of the
primary seal against contaminants or corrosion
and they can be used to enhance the efficiency
of labyrinth seals († fig. 8).
Fig. 8
V-rings in a labyrinth seal
Sliding velocities
V-rings can operate under the conditions listed
in table 2. In the speed range 15 to 20 m/s
(2 900 to 3 900 ft/min), the sealing lip lifts from
the counterface and the V-ring only acts as a
gap-type seal.
Table 2
Permissible operating conditions
1 2 3
normal located axially1) axial and radial support1)
Operating conditions Guideline values for V-rings of

nitrile rubber fluoro rubber
Temperature, °C (°F) –40 to +100 (–40 to +210) –20 to +150 (–4 to +300) 7
Circumferential speed, m/s (ft/min)
normal (1) up to 8 (1 575) up to 6,5 (1 280)
located axially (2) 8 to 12 (1 575 to 2 360) 6,5 to 10 (1 280 to 1 970)
axial and radial support (3) >12 (2 360) >10 (1 970)
Pressure acting on seal, MPa (psi)

static sealing or very low
speed operation up to 0,03 (4.35) up to 0,03 (4.35)
1) Support ring by customer
V-ring seals
Coaxiality and runout The permissible misalignment values for the

very compact VL/VR3 design are appreciably
The total tolerance for the deviation from coaxi- lower than those for the VA/VR1 and VS/VR2
ality and runout should not exceed the guideline designs.
values provided in table 3. In applications where V-rings are not sup-
ported axially on the shaft, the maximum value
in the diagram should be reduced.
Misalignment
V-rings can tolerate misalignment between the
shaft and housing, i.e. deviations from the per-
pendicularity between the shaft and counterface
of the housing. Guideline values for the max
imum permissible angular misalignment are
provided in diagram 1. These values apply to
the V-ring designs VA/VR1 and VS/VR2, provid-
ed they are supported axially on the shaft.
Table 3
Coaxiality and runout tolerances
Kd1
Shaft diameter Total tolerance

nominal for coaxiality
deviation and runout
d1 Kd1
over incl. over incl. max
mm in. mm in.
V-rings, VA/VR1 and VS/VR2 designs

9,5 0.374 0,4 0.016
9,5 19,5 0.374 0.768 0,6 0.024
19,5 38 0.768 1.496 0,9 0.034
38 68 1.496 2.677 1,1 0.043
68 105 2.677 4.134 1,4 0.055

105 155 4.134 6.102 1,6 0.063
155 210 6.102 8.628 1,9 0.075
210 2 020 8.628 79.527 3,6 0.142
V-rings, VL/VR3 designs

135 630 5.315 24.803 1,5 0.059
V-rings, VE/VR4 designs

450 2 010 17.716 79.134 6 0.236
Counterface Additional counterface information

Aluminium surfaces should be free of scratch
A fine-turned counterface is adequate for marks. Surface hardness should be > 100 HB
V-rings. The appropriate surface roughness in abrasive applications. Die cast aluminium can
values vary depending on the circumferential be used in the as-cast condition.
speed († table 4 on page 398). SKF recom- Steel and cast iron surfaces should be free
mends buffing all turned surfaces with an emery from lead and sharp tool marks. Cold rolled steel
cloth to remove any sharp peaks arising from stampings can be used without machining.
the turning operation. The surface finish should Plastic counterface materials are generally
be measured at approximately 90 degrees to not acceptable due to poor heat dissipation.
the path of the groove to obtain a true reading Stainless steel should not be used in dry-
of the surface. running applications unless the speed is below
1 m/s (200 ft/min).
Counterface treatment
In the presence of grease, oil or dry lubricants,
no special counterface treatment is required.
Mild steel counterfaces that are exposed to water
or other corrosives should be protected, for ex-
ample by zinc- or chromium-plating or treated
with an anti-corrosive spray.
Diagram 1
Maximum permissible misalignment for V-rings of the VA/VR1 and VS/VR2 designs
?a 7
Misalignment
a, degrees
4,0
3,0
2,0
1,0
0
0 100 200 300 400 500 600 700 800 900 1 000
(3.937) (7.874) (11.811) (15.748) (19.685) (23.622) (27.559) (31.496) (35.433) (39.370)
V-ring seals
Table 4
Product table sorting order
Recommended counterface surface finish
Circumferential speed Surface finish

When searching for a suitable V-ring for a given
shaft diameter, e.g. 930 mm, first identify the
m/s ft/min. Ra µm Ra µin. possible shaft diameter ranges (d1). In this case,
there are three possible ranges († fig. 9a).
> 10 > 1 969 0,4–0,8 16–32 Then look for the appropriate dimensions D1,
5–10 984–1 969 0,8–1,6 32–64 D and B1 that are listed in ascending order
1–5 199–984 1,6–2,0 64–80
(† fig. 9b). Please note that this sorting order
concept results in that the shaft diameter ranges
<1 < 199 2,0–2,5 80–100 do not always come in ascending order, e.g. here
925–975 mm is listed before 920–965 mm.
The surface finish must not be lower than Ra 0,05 µm (2 µin.).
Dimensions
Shaft diameter
range Seal inside dia
d1 meter, free state Seal Nominal Nominal
seat width seal
over d width seal heig Clearance Counterface Seal fitted
Lip Designation
incl . b1 b ht code
c D1 width Fig. 9
mm D B1
max min
851 861 –
824 –
32,5 65
824 30
32,5 65 d1 + 24
861ension 21 d1 + 115 50 ± 12
Dim 871
s 833 d1 + 24 d1 + 115 R
32,5 50 ± 12 860 VE R
Shaft diameter 833l insi 65 R
Sea de dia 32, 30 d1 + 24 860 VRME R
range
meter, free state Sea5l 65
Nominal d1 + 115
d871 882 21 inal
Nom d1 + 24 50 ± 12
1
d843 seat width seal width seal Clea rance d1 +nter
Cou 115face 50 ± 12 R
Lip 870
32, height VEatio
Design R n
over incl . 843 b1 5 65
b Seal fitted R
code 870 VRME R
32,5 30
c d11+ 24 width
65 21 D d
D1 + 115
875
mm 925 d1 + 24
max 50
B1 ± 12 R
825 d1 + 115
min 50 ± 12 880 VE R
6 10,5 R
825 6,5 880 VRME R
6 10,5 d1 + 5
875 6,5 d1 + 20 8 ± 1,5
851 920
861 825 d1 + 5 d1 + 20 R
824 14,5 8 ± 1,5 – 900
– VL R
825 32, 3 25 V
824 14,5 65 15
30 900 VL V
32, 3 25
65 15 dd11 ++ 24
10
dd11 ++ 115
45
882
861 892 21 dd11 ++ 24
10 20 ±± 12
50 4 R
871 853
833 dd11 ++ 115
45 R 900 VE
860 VA R
R
32,5
32, 5 65 20 ±± 12
50 4 V
853
833 65 30 R 900 VRM
860 VA VE R
32,5
32, 5 65 30 dd11 ++ 24
24
892 65 21
21 dd11 ++ 115
115 50 ±± 12
12
871 912
882 871
843 dd11 ++ 24
24
dd11 ++ 115
115
50 R
R 890 VE
32,5
32, 5 50 ±± 12
50 12 870 VE R
R
871
843 65
65 30 R
R 890 VRM
VRME
32,5
32, 5 30 dd11 ++ 24
24 870 ER
R
65
65 21 dd11 ++ 115
115
912
875 922 21 dd11 ++ 24
24 50 ±± 12
50 12 R
925 880
825 dd11 ++ 115
115 R 900 VE
880 VE R
R
32,5
6 65 5 50 ±± 12
50 12 R
880
925
a 825 32,5
6
10,
65 5
10,
30
6,5
21
6,5
dd11 ++ 5
24
dd11 ++ 20
115 50± ±1,5
12
R 900 VRM
880 VRMEER
R
875 975
920 865
825 dd11 ++ 524
dd11 ++ 20
115
8 R
R 920 VL
6 3
14, 50± ±1,5
8 12 900 VE R
R
865
825 10,5
25 6,5 R
V 920 VL
VRM
900
920
882 965
892 865
6 3
14, 10,5
25
15
6,5
15
dd11 ++ 10
5
dd11 ++ 10
5
dd11 ++ 45
20 8 ±±1,5
20 4
b R
VE R
853 14,53 dd11 ++ 45
20 8 ±±1,5
20
R 950 VA
900 VL R
R
865 32, 25
65 4 V
V 950 VA
853 14,5 15
30 900 VL V
V
32, 3 25
65 15 dd11 ++ 24
10
dd11 ++ 115
45
922
892 933 21 dd11 ++ 24
10 20 ±± 12
50 4 R
912 890
871 dd11 ++ 115
45 R 950 VE
890 VA R
R
32,5
32, 5 65 20 ±± 12
50 4 V
890
871 65 30 R 950 VRM
890 VA VE R
32,5
32, 5 65 30 dd11 ++ 24
24
933 65 21
21 dd11 ++ 115
115 50 ±± 12
12
912 944
922 900
880 dd11 ++ 24
24
dd11 ++ 115
115
50 R
R 930 VE
32,5
32, 5 50 ±± 12
50 12 900 VE R
R
900
880 65
65 30 R
R 930 VRM
VRME
32,5
32, 5 30 dd11 ++ 24
24 900 ER
R
65
65 21 dd11 ++ 115
115
944
925 955 21 dd11 ++ 24
24 50 ±± 12
50 12 R
975 911
865 dd11 ++ 115
115 R 940 VE
920 VE R
R
32,5
6 65 5 50 ±± 12
50 12 R
911
865 10, 30 R 940 VRM
920 VRMEER
32,5
6 65 5 6,5 dd11 ++ 5
24 R
955 10, 21
6,5 dd11 ++ 20
115 50± ±1,5
12
920 966
965 921
865 dd11 ++ 524
dd11 ++ 20
115
8 R
R 950 VL
32,3
14, 5 50± ±1,5
8 12 950 VE R
R
921
865 65
25 30 R
V 950 VL
VRM
950
398 975
922 1025
933 910
32,3
14, 5 65
15
21
15
dd ++ 10
24
dd ++ 10
24
dd ++ 45
d
115 11
50 ±± 4
20 12 11
R
VE R
890 6 5
11 d11 ++ 45
115 50 ±± 4
20 12
R 960 VA
950 VE R
R
910 32, 10,5
65 R
V 960 VA
890 6 5 6,5
30 950 VRMVE R
32, 10,5
65 6,5 dd11 ++ 24
5
dd11 ++ 115
20
965
933 1015 21 dd1 ++ 5 8 ±±1,5
50 12 R
9
Shaft requirements Fig. 10
Installing a V-ring
Sharp edges, nicks and burrs on the shaft must
be avoided to prevent damage to the V-ring
during installation.
V-rings rotate with the shaft and only require
a moderate surface roughness value. As a general
guideline, the value should not exceed Ra 6,3 µm
(252 µin.). When sealing fluids or exposed to
fine, solid contaminants, the V-ring requires a
surface roughness value of maximum Ra 3,2 µm
(128 µin.).
A V-ring is stretched when installed and fits
all shaft diameters within the ranges listed in
the product tables.
Installing V-rings Fig. 11
V-rings are elastic and can be stretched and Installation tool

pushed over other components, which facilitates
the installation († fig. 10). When several V-rings
are to be installed, a simple tool († fig. 11) can
be used to push the seals to their position at a
predetermined distance from the counterface.
V-rings can also be cut and rejoined in the field.
The general installation guidelines include the
following:
• Clean the V-ring, counterface and shaft.

• Make sure that the shaft is dry and free from
grease or oil, particularly when installing a
V-ring without axial support.
• Lubricate the lip of the V-ring with a thin film
of grease or silicone oil.
• In applications where friction must be reduced
to a minimum, the counterface should be
coated with a low-friction agent. Do not apply
grease to the lip. 7
• Check that the V-ring is installed with a
uniform stretch around the shaft.
V-ring seals – metric dimensions, globally valid outside North American market
d1 2,7 – 53 mm
B1
d D1 d1 D
b1
Dimensions Lip Designation

Shaft diameter Seal inside dia Seal Nominal Nominal Clearance Counterface Seal fitted code
range meter, free state seat width seal width seal height width
d1 d b1 b c D1 D B1
over incl. max min
mm – –
2,7 3,5 2,5 2,1 3 1,5 d1 + 1 d1 + 4 2,5 ± 0,3 R 3 VA R

2,5 2,1 3 1,5 d1 + 1 d1 + 4 2,5 ± 0,3 V 3 VA V
3,5 4,5 3,2 2,4 3,7 2 d1 + 1 d1 + 6 3 ± 0,4 R 4 VA R

3,2 2,4 3,7 2 d1 + 1 d1 + 6 3 ± 0,4 V 4 VA V
4,5 5,5 4 2,4 3,7 2 d1 + 1 d1 + 6 3 ± 0,4 R 5 VA R

4 2,4 3,7 2 d1 + 1 d1 + 6 3 ± 0,4 V 5 VA V
4 3,9 5,2 2 d1 + 1 d1 + 6 4,5 ± 0,4 R 5 VS R
4 3,9 5,2 2 d1 + 1 d1 + 6 4,5 ± 0,4 V 5 VS V
5,5 6,5 5 2,4 3,7 2 d1 + 1 d1 + 6 3 ± 0,4 R 6 VA R

5 2,4 3,7 2 d1 + 1 d1 + 6 3 ± 0,4 V 6 VA V
5 3,9 5,2 2 d1 + 1 d1 + 6 4,5 ± 0,4 R 6 VS R
5 3,9 5,2 2 d1 + 1 d1 + 6 4,5 ± 0,4 V 6 VS V
6,5 8 6 2,4 3,7 2 d1 + 1 d1 + 6 3 ± 0,4 R 7 VA R

6 2,4 3,7 2 d1 + 1 d1 + 6 3 ± 0,4 V 7 VA V
6 3,9 5,2 2 d1 + 1 d1 + 6 4,5 ± 0,4 R 7 VS R
6 3,9 5,2 2 d1 + 1 d1 + 6 4,5 ± 0,4 V 7 VS V
8 9,5 7 2,4 3,7 2 d1 + 1 d1 + 6 3 ± 0,4 R 8 VA R

7 2,4 3,7 2 d1 + 1 d1 + 6 3 ± 0,4 V 8 VA V
7 3,9 5,2 2 d1 + 1 d1 + 6 4,5 ± 0,4 R 8 VS R
7 3,9 5,2 2 d1 + 1 d1 + 6 4,5 ± 0,4 V 8 VS V
9,5 11,5 9 3,4 5,5 3 d1 + 1 d1 + 9 4,5 ± 0,6 R 10 VA R

9 3,4 5,5 3 d1 + 1 d1 + 9 4,5 ± 0,6 V 10 VA V
9 5,6 7,7 3 d1 + 1 d1 + 9 6,7 ± 0,6 R 10 VS R
9 5,6 7,7 3 d1 + 1 d1 + 9 6,7 ± 0,6 V 10 VS V
11,5 12,5 10,5 3,4 5,5 3 d1 + 1 d1 + 9 4,5 ± 0,6 R 12 VA R

10,5 3,4 5,5 3 d1 + 1 d1 + 9 4,5 ± 0,6 V 12 VA V
11,5 13,5 10,5 5,6 7,7 3 d1 + 1 d1 + 9 6,7 ± 0,6 R 12 VS R

10,5 5,6 7,7 3 d1 + 1 d1 + 9 6,7 ± 0,6 V 12 VS V
11,7 3,4 5,5 3 d1 + 1 d1 + 9 4,5 ± 0,6 R 13 VA R
11,7 3,4 5,5 3 d1 + 1 d1 + 9 4,5 ± 0,6 V 13 VA V
13,5 15,5 12,5 3,4 5,5 3 d1 + 1 d1 + 9 4,5 ± 0,6 R 14 VA R

12,5 3,4 5,5 3 d1 + 1 d1 + 9 4,5 ± 0,6 V 14 VA V

d1 d b1 b c D1 D B1
over incl. max min
mm – –
13,5 15,5 12,5 5,6 7,7 3 d1 + 1 d1 + 9 6,7 ± 0,6 R 14 VS R

cont. 12,5 5,6 7,7 3 d1 + 1 d1 + 9 6,7 ± 0,6 V 14 VS V
15,5 17 14 3,4 5,5 3 d1 + 1 d1 + 9 4,5 ± 0,6 R 16 VA R

14 3,4 5,5 3 d1 + 1 d1 + 9 4,5 ± 0,6 V 16 VA V
15,5 17,5 14 5,6 7,7 3 d1 + 1 d1 + 9 6,7 ± 0,6 R 16 VS R

14 5,6 7,7 3 d1 + 1 d1 + 9 6,7 ± 0,6 V 16 VS V
17,5 19 16 3,4 5,5 3 d1 + 1 d1 + 9 4,5 ± 0,6 R 18 VA R

16 3,4 5,5 3 d1 + 1 d1 + 9 4,5 ± 0,6 V 18 VA V
16 5,6 7,7 3 d1 + 1 d1 + 9 6,7 ± 0,6 R 18 VS R
16 5,6 7,7 3 d1 + 1 d1 + 9 6,7 ± 0,6 V 18 VS V
19 21 18 4,7 7,5 4 d1 + 2 d1 + 12 6 ± 0,8 R 20 VA R

18 4,7 7,5 4 d1 + 2 d1 + 12 6 ± 0,8 V 20 VA V
18 7,9 10,5 4 d1 + 2 d1 + 12 9 ± 0,8 R 20 VS R
18 7,9 10,5 4 d1 + 2 d1 + 12 9 ± 0,8 V 20 VS V
21 24 20 4,7 7,5 4 d1 + 2 d1 + 12 6 ± 0,8 R 22 VA R

20 4,7 7,5 4 d1 + 2 d1 + 12 6 ± 0,8 V 22 VA V
20 7,9 10,5 4 d1 + 2 d1 + 12 9 ± 0,8 R 22 VS R
20 7,9 10,5 4 d1 + 2 d1 + 12 9 ± 0,8 V 22 VS V
24 27 22 4,7 7,5 4 d1 + 2 d1 + 12 6 ± 0,8 R 25 VA R

22 4,7 7,5 4 d1 + 2 d1 + 12 6 ± 0,8 V 25 VA V
22 7,9 10,5 4 d1 + 2 d1 + 12 9 ± 0,8 R 25 VS R
22 7,9 10,5 4 d1 + 2 d1 + 12 9 ± 0,8 V 25 VS V
27 29 25 4,7 7,5 4 d1 + 2 d1 + 12 6 ± 0,8 R 28 VA R

25 4,7 7,5 4 d1 + 2 d1 + 12 6 ± 0,8 V 28 VA V
25 7,9 10,5 4 d1 + 2 d1 + 12 9 ± 0,8 R 28 VS R
25 7,9 10,5 4 d1 + 2 d1 + 12 9 ± 0,8 V 28 VS V
29 31 27 4,7 7,5 4 d1 + 2 d1 + 12 6 ± 0,8 R 30 VA R

27 4,7 7,5 4 d1 + 2 d1 + 12 6 ± 0,8 V 30 VA V
27 7,9 10,5 4 d1 + 2 d1 + 12 9 ± 0,8 R 30 VS R
27 7,9 10,5 4 d1 + 2 d1 + 12 9 ± 0,8 V 30 VS V
31 33 29 4,7 7,5 4 d1 + 2 d1 + 12 6 ± 0,8 R 32 VA R

29 4,7 7,5 4 d1 + 2 d1 + 12 6 ± 0,8 V 32 VA V
29 7,9 10,5 4 d1 + 2 d1 + 12 9 ± 0,8 R 32 VS R
29 7,9 10,5 4 d1 + 2 d1 + 12 9 ± 0,8 V 32 VS V
33 36 31 4,7 7,5 4 d1 + 2 d1 + 12 6 ± 0,8 R 35 VA R

31 4,7 7,5 4 d1 + 2 d1 + 12 6 ± 0,8 V 35 VA V
31 7,9 10,5 4 d1 + 2 d1 + 12 9 ± 0,8 R 35 VS R
31 7,9 10,5 4 d1 + 2 d1 + 12 9 ± 0,8 V 35 VS V 7.1
36 38 34 4,7 7,5 4 d1 + 2 d1 + 12 6 ± 0,8 R 38 VA R
34 4,7 7,5 4 d1 + 2 d1 + 12 6 ± 0,8 V 38 VA V
34 7,9 10,5 4 d1 + 2 d1 + 12 9 ± 0,8 R 38 VS R
34 7,9 10,5 4 d1 + 2 d1 + 12 9 ± 0,8 V 38 VS V
38 43 36 5,5 9 5 d1 + 2 d1 + 15 7 ± 1 R 40 VA R

36 5,5 9 5 d1 + 2 d1 + 15 7 ± 1 V 40 VA V
36 9,5 13 5 d1 + 2 d1 + 15 11 ± 1 R 40 VS R
36 9,5 13 5 d1 + 2 d1 + 15 11 ± 1 V 40 VS V
43 48 40 5,5 9 5 d1 + 2 d1 + 15 7 ± 1 R 45 VA R

40 5,5 9 5 d1 + 2 d1 + 15 7 ± 1 V 45 VA V
40 9,5 13 5 d1 + 2 d1 + 15 11 ± 1 R 45 VS R
40 9,5 13 5 d1 + 2 d1 + 15 11 ± 1 V 45 VS V
48 53 45 5,5 9 5 d1 + 2 d1 + 15 7 ± 1 R 50 VA R

45 5,5 9 5 d1 + 2 d1 + 15 7 ± 1 V 50 VA V
45 9,5 13 5 d1 + 2 d1 + 15 11 ± 1 R 50 VS R
45 9,5 13 5 d1 + 2 d1 + 15 11 ± 1 V 50 VS V
d1 53 – 195 mm
B1
d D1 d1 D
b1

d1 d b1 b c D1 D B1
over incl. max min
mm – –
53 58 49 5,5 9 5 d1 + 2 d1 + 15 7 ± 1 R 55 VA R

49 5,5 9 5 d1 + 2 d1 + 15 7 ± 1 V 55 VA V
49 9,5 13 5 d1 + 2 d1 + 15 11 ± 1 R 55 VS R
49 9,5 13 5 d1 + 2 d1 + 15 11 ± 1 V 55 VS V
58 63 54 5,5 9 5 d1 + 2 d1 + 15 7 ± 1 R 60 VA R

54 5,5 9 5 d1 + 2 d1 + 15 7 ± 1 V 60 VA V
54 9,5 13 5 d1 + 2 d1 + 15 11 ± 1 R 60 VS R
54 9,5 13 5 d1 + 2 d1 + 15 11 ± 1 V 60 VS V
63 68 58 5,5 9 5 d1 + 2 d1 + 15 7 ± 1 R 65 VA R

58 5,5 9 5 d1 + 2 d1 + 15 7 ± 1 V 65 VA V
58 9,5 13 5 d1 + 2 d1 + 15 11 ± 1 R 65 VS R
58 9,5 13 5 d1 + 2 d1 + 15 11 ± 1 V 65 VS V
68 73 63 6,8 11 6 d1 + 3 d1 + 18 9 ± 1,2 R 70 VA R

63 6,8 11 6 d1 + 3 d1 + 18 9 ± 1,2 V 70 VA V
63 11,3 15,5 6 d1 + 3 d1 + 18 13,5 ± 1,2 R 70 VS R
63 11,3 15,5 6 d1 + 3 d1 + 18 13,5 ± 1,2 V 70 VS V
73 78 67 6,8 11 6 d1 + 3 d1 + 18 9 ± 1,2 R 75 VA R

67 6,8 11 6 d1 + 3 d1 + 18 13,5 ± 1,2 R 75 VS R
67 11,3 15,5 6 d1 + 3 d1 + 18 13,5 ± 1,2 V 75 VS V
78 83 72 6,8 11 6 d1 + 3 d1 + 18 9 ± 1,2 R 80 VA R

72 6,8 11 6 d1 + 3 d1 + 18 9 ± 1,2 V 80 VA V
72 11,3 15,5 6 d1 + 3 d1 + 18 13,5 ± 1,2 R 80 VS R
72 11,3 15,5 6 d1 + 3 d1 + 18 13,5 ± 1,2 V 80 VS V
83 88 76 6,8 11 6 d1 + 3 d1 + 18 9 ± 1,2 R 85 VA R

76 6,8 11 6 d1 + 3 d1 + 18 9 ± 1,2 V 85 VA V
76 11,3 15,5 6 d1 + 3 d1 + 18 13,5 ± 1,2 R 85 VS R
76 11,3 15,5 6 d1 + 3 d1 + 18 13,5 ± 1,2 V 85 VS V
88 93 81 6,8 11 6 d1 + 3 d1 + 18 9 ± 1,2 R 90 VA R

81 6,8 11 6 d1 + 3 d1 + 18 9 ± 1,2 V 90 VA V
81 11,3 15,5 6 d1 + 3 d1 + 18 13,5 ± 1,2 R 90 VS R
81 11,3 15,5 6 d1 + 3 d1 + 18 13,5 ± 1,2 V 90 VS V
93 98 85 6,8 11 6 d1 + 3 d1 + 18 9 ± 1,2 R 95 VA R

85 6,8 11 6 d1 + 3 d1 + 18 9 ± 1,2 V 95 VA V
85 11,3 15,5 6 d1 + 3 d1 + 18 13,5 ± 1,2 R 95 VS R
85 11,3 15,5 6 d1 + 3 d1 + 18 13,5 ± 1,2 V 95 VS V

d1 d b1 b c D1 D B1
over incl. max min
mm – –
98 105 90 6,8 11 6 d1 + 3 d1 + 18 9 ± 1,2 R 100 VA R

90 6,8 11 6 d1 + 3 d1 + 18 9 ± 1,2 V 100 VA V
90 11,3 15,5 6 d1 + 3 d1 + 18 13,5 ± 1,2 R 100 VS R
90 11,3 15,5 6 d1 + 3 d1 + 18 13,5 ± 1,2 V 100 VS V
105 115 99 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 R 110 VL R

99 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 V 110 VL V
99 7,9 12,8 7 d1 + 4 d1 + 21 10,5 ± 1,5 R 110 VA R
99 7,9 12,8 7 d1 + 4 d1 + 21 10,5 ± 1,5 V 110 VA V
99 13,1 18 7 d1 + 4 d1 + 21 15,5 ± 1,5 R 110 VS R
99 13,1 18 7 d1 + 4 d1 + 21 15,5 ± 1,5 V 110 VS V
115 125 108 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 R 120 VL R

108 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 V 120 VL V
108 7,9 12,8 7 d1 + 4 d1 + 21 10,5 ± 1,5 R 120 VA R
108 7,9 12,8 7 d1 + 4 d1 + 21 10,5 ± 1,5 V 120 VA V
108 13,1 18 7 d1 + 4 d1 + 21 15,5 ± 1,5 R 120 VS R
108 13,1 18 7 d1 + 4 d1 + 21 15,5 ± 1,5 V 120 VS V
125 135 117 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 R 130 VL R

117 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 V 130 VL V
117 7,9 12,8 7 d1 + 4 d1 + 21 10,5 ± 1,5 R 130 VA R
117 7,9 12,8 7 d1 + 4 d1 + 21 10,5 ± 1,5 V 130 VA V
117 13,1 18 7 d1 + 4 d1 + 21 15,5 ± 1,5 R 130 VS R
117 13,1 18 7 d1 + 4 d1 + 21 15,5 ± 1,5 V 130 VS V
135 145 126 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 R 140 VL R

126 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 V 140 VL V
126 7,9 12,8 7 d1 + 4 d1 + 21 10,5 ± 1,5 R 140 VA R
126 7,9 12,8 7 d1 + 4 d1 + 21 10,5 ± 1,5 V 140 VA V
126 13,1 18 7 d1 + 4 d1 + 21 15,5 ± 1,5 R 140 VS R
126 13,1 18 7 d1 + 4 d1 + 21 15,5 ± 1,5 V 140 VS V
145 155 135 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 R 150 VL R

135 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 V 150 VL V
135 7,9 12,8 7 d1 + 4 d1 + 21 10,5 ± 1,5 R 150 VA R
135 7,9 12,8 7 d1 + 4 d1 + 21 10,5 ± 1,5 V 150 VA V
135 13,1 18 7 d1 + 4 d1 + 21 15,5 ± 1,5 R 150 VS R
135 13,1 18 7 d1 + 4 d1 + 21 15,5 ± 1,5 V 150 VS V
155 165 144 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 R 160 VL R

144 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 V 160 VL V
144 9 14,5 8 d1 + 4 d1 + 24 12 ± 1,8 R 160 VA R
144 9 14,5 8 d1 + 4 d1 + 24 12 ± 1,8 V 160 VA V
144 15 20,5 8 d1 + 4 d1 + 24 18 ± 1,8 R 160 VS R
144 15 20,5 8 d1 + 4 d1 + 24 18 ± 1,8 V 160 VS V
165 175 153 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 R 170 VL R 7.1
153 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 V 170 VL V
153 9 14,5 8 d1 + 4 d1 + 24 12 ± 1,8 R 170 VA R
153 9 14,5 8 d1 + 4 d1 + 24 12 ± 1,8 V 170 VA V
153 15 20,5 8 d1 + 4 d1 + 24 18 ± 1,8 R 170 VS R
153 15 20,5 8 d1 + 4 d1 + 24 18 ± 1,8 V 170 VS V
175 185 162 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 R 180 VL R

162 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 V 180 VL V
162 9 14,5 8 d1 + 4 d1 + 24 12 ± 1,8 R 180 VA R
162 9 14,5 8 d1 + 4 d1 + 24 12 ± 1,8 V 180 VA V
162 15 20,5 8 d1 + 4 d1 + 24 18 ± 1,8 R 180 VS R
162 15 20,5 8 d1 + 4 d1 + 24 18 ± 1,8 V 180 VS V
185 195 171 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 R 190 VL R

171 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 V 190 VL V
171 9 14,5 8 d1 + 4 d1 + 24 12 ± 1,8 R 190 VA R
171 9 14,5 8 d1 + 4 d1 + 24 12 ± 1,8 V 190 VA V
171 15 20,5 8 d1 + 4 d1 + 24 18 ± 1,8 R 190 VS R
171 15 20,5 8 d1 + 4 d1 + 24 18 ± 1,8 V 190 VS V
d1 190 – 395 mm
B1
d D1 d1 D
b1

d1 d b1 b c D1 D B1
over incl. max min
mm – –
195 210 182 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 R 200 VL R

182 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 V 200 VL V
180 9 14,5 8 d1 + 4 d1 + 24 12 ± 1,8 R 199 VA R
180 9 14,5 8 d1 + 4 d1 + 24 12 ± 1,8 V 199 VA V
180 15 20,5 8 d1 + 4 d1 + 24 18 ± 1,8 R 199 VS R
180 15 20,5 8 d1 + 4 d1 + 24 18 ± 1,8 V 199 VS V
190 210 180 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 R 200 VA R

180 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 V 200 VA V
210 233 198 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 R 220 VL R

198 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 V 220 VL V
198 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 R 220 VA R
198 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 V 220 VA V
233 260 225 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 R 250 VL R

225 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 V 250 VL V
235 265 225 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 R 250 VA R

225 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 V 250 VA V
260 285 247 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 R 275 VL R

247 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 V 275 VL V
265 290 247 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 R 275 VA R

247 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 V 275 VA V
285 310 270 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 R 300 VL R

270 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 V 300 VL V
290 310 270 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 R 300 VA R

270 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 V 300 VA V
300 305 294 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 300 VE R

294 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 300 VRME R
305 310 299 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 305 VE R

299 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 305 VRME R
310 335 292 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 R 325 VL R

292 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 V 325 VL V

d1 d b1 b c D1 D B1
over incl. max min
mm – –
310 335 292 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 R 325 VA R

cont. 292 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 V 325 VA V
310 315 304 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 310 VE R

304 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 310 VRME R
315 320 309 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 315 VE R

309 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 315 VRME R
320 325 314 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 320 VE R

314 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 320 VRME R
325 330 319 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 325 VE R

319 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 325 VRME R
330 335 323 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 330 VE R

323 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 330 VRME R
335 365 315 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 R 350 VL R

315 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 V 350 VL V
315 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 R 350 VA R
315 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 V 350 VA V
335 340 328 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 335 VE R

328 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 335 VRME R
340 345 333 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 340 VE R

328 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 340 VRME R
345 350 338 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 345 VE R

338 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 345 VRME R
350 355 343 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 350 VE R

343 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 350 VRME R
355 360 347 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 355 VE R

347 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 355 VRME R
360 365 352 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 360 VE R

357 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 360 VRME R
365 385 337 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 R 375 VL R

337 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 V 375 VL V
365 390 337 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 R 375 VA R

337 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 V 375 VA V
365 370 357 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 365 VE R 7.1

370 375 362 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 370 VE R
362 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 370 VRME R
375 380 367 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 375 VE R

367 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 375 VRME R
380 385 371 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 380 VE R

371 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 380 VRME R
385 410 360 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 R 400 VL R

360 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 V 400 VL V
390 430 360 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 R 400 VA R

360 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 V 400 VA V
385 390 376 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 385 VE R

376 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 385 VRME R
390 395 381 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 390 VE R

381 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 390 VRME R
d1 395 – 540 mm
B1
d D1 d1 D
b1

d1 d b1 b c D1 D B1
over incl. max min
mm – –
395 400 386 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 395 VE R

386 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 395 VRME R
400 405 391 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 400 VE R

391 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 400 VRME R
405 410 396 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 405 VE R

396 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 405 VRME R
410 415 401 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 410 VE R

401 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 410 VRME R
415 420 405 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 415 VE R

405 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 415 VRME R
420 425 410 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 420 VE R

410 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 420 VRME R
425 430 415 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 425 VE R

415 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 425 VRME R
410 440 382 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 R 425 VL R

382 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 V 425 VL V
440 475 405 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 R 450 VL R

405 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 V 450 VL V
430 480 405 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 R 450 VA R

405 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 V 450 VA V
430 435 420 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 430 VE R

420 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 430 VRME R
435 440 425 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 435 VE R

425 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 435 VRME R
440 445 429 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 440 VE R

429 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 440 VRME R
445 450 434 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 445 VE R

434 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 445 VRME R

d1 d b1 b c D1 D B1
over incl. max min
mm – –
450 455 439 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 450 VE R

439 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 450 VRME R
455 460 444 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 455 VE R

444 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 455 VRME R
460 465 448 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 460 VE R

448 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 460 VRME R
465 470 453 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 465 VE R

453 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 465 VRME R
470 475 458 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 470 VE R

458 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 470 VRME R
475 480 463 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 475 VE R

463 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 475 VRME R
475 510 450 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 R 500 VL R

450 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 V 500 VL V
510 540 472 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 R 525 VL R

472 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 V 525 VL V
480 530 450 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 R 500 VA R

450 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 V 500 VA V
480 485 468 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 480 VE R

468 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 480 VRME R
485 490 473 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 485 VE R

473 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 485 VRME R
490 495 478 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 490 VE R

478 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 490 VRME R
495 500 483 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 495 VE R

483 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 495 VRME R
500 505 488 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 500 VE R

488 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 500 VRME R
505 510 493 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 505 VE R

493 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 505 VRME R
510 515 497 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 510 VE R

497 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 510 VRME R
7.1
515 520 502 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 515 VE R
502 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 515 VRME R
520 525 507 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 520 VE R

507 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 520 VRME R
525 530 512 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 525 VE R

512 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 525 VRME R
540 575 495 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 R 550 VL R

495 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 V 550 VL V
530 580 495 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 R 550 VA R

495 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 V 550 VA V
530 535 517 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 530 VE R

517 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 530 VRME R
535 540 521 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 535 VE R

521 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 535 VRME R
d1 540 – 758 mm
B1
d D1 d1 D
b1

d1 d b1 b c D1 D B1
over incl. max min
mm – –
540 545 526 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 540 VE R

526 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 540 VRME R
545 550 531 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 545 VE R

531 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 545 VRME R
550 555 536 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 550 VE R

536 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 550 VRME R
555 560 541 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 555 VE R

541 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 555 VRME R
560 565 546 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 560 VE R

546 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 560 VRME R
565 570 550 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 565 VE R

550 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 565 VRME R
570 575 555 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 570 VE R

555 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 570 VRME R
575 580 560 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 575 VE R

560 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 575 VRME R
575 625 540 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 R 600 VL R

540 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 V 600 VL V
580 630 540 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 R 600 VA R

540 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 V 600 VA V
580 585 565 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 580 VE R

565 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 580 VRME R
585 590 570 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 585 VE R

570 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 585 VRME R
590 600 575 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 590 VE R

575 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 590 VRME R
600 610 582 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 600 VE R

582 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 600 VRME R

d1 d b1 b c D1 D B1
over incl. max min
mm – –
610 620 592 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 610 VE R

592 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 610 VRME R
620 630 602 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 620 VE R

602 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 620 VRME R
615 675 600 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 R 650 VL R

600 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 V 650 VL V
630 665 600 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 R 650 VA R

600 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 V 650 VA V
630 640 612 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 630 VE R

612 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 630 VRME R
640 650 621 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 640 VE R

621 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 640 VRME R
650 660 631 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 650 VE R

631 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 650 VRME R
660 670 640 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 660 VE R

640 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 660 VRME R
675 710 630 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 R 700 VL R

630 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 V 700 VL V
665 705 630 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 R 700 VA R

630 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 V 700 VA V
670 680 650 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 670 VE R

650 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 670 VRME R
680 690 660 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 680 VE R

660 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 680 VRME R
690 700 670 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 690 VE R

670 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 690 VRME R
700 710 680 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 700 VE R

680 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 700 VRME R
710 740 670 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 R 725 VL R

670 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 V 725 VL V
705 745 670 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 R 725 VA R

670 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 V 725 VA V
7.1
710 720 689 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 710 VE R
689 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 710 VRME R
720 730 699 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 720 VE R

699 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 720 VRME R
730 740 709 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 730 VE R

709 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 730 VRME R
740 750 718 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 740 VE R

718 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 740 VRME R
740 775 705 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 R 750 VL R

705 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 V 750 VL V
745 785 705 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 R 750 VA R

705 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 V 750 VA V
750 758 728 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 750 VE R

728 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 750 VRME R
d1 758 – 1 065 mm
B1
d D1 d1 D
b1

d1 d b1 b c D1 D B1
over incl. max min
mm – –
758 766 735 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 760 VE R

735 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 760 VRME R
766 774 743 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 770 VE R

743 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 770 VRME R
774 783 751 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 780 VE R

751 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 780 VRME R
783 792 759 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 790 VE R

759 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 790 VRME R
775 825 745 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 R 800 VL R

745 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 V 800 VL V
785 830 745 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 R 800 VA R

745 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 V 800 VA V
792 801 768 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 800 VE R

768 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 800 VRME R
801 810 777 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 810 VE R

777 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 810 VRME R
810 821 786 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 820 VE R

786 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 820 VRME R
821 831 796 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 830 VE R

796 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 830 VRME R
825 875 785 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 R 850 VL R

785 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 V 850 VL V
830 875 785 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 R 850 VA R

785 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 V 850 VA V
831 841 805 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 840 VE R

805 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 840 VRME R
841 851 814 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 850 VE R

814 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 850 VRME R

d1 d b1 b c D1 D B1
over incl. max min
mm – –
851 861 824 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 860 VE R

824 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 860 VRME R
861 871 833 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 870 VE R

833 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 870 VRME R
871 882 843 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 880 VE R

843 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 880 VRME R
875 925 825 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 R 900 VL R

825 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 V 900 VL V
875 920 825 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 R 900 VA R

825 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 V 900 VA V
882 892 853 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 890 VE R

853 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 890 VRME R
892 912 871 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 900 VE R

871 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 900 VRME R
912 922 880 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 920 VE R

880 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 920 VRME R
925 975 865 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 R 950 VL R

865 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 V 950 VL V
920 965 865 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 R 950 VA R

865 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 V 950 VA V
922 933 890 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 930 VE R

890 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 930 VRME R
933 944 900 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 940 VE R

900 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 940 VRME R
944 955 911 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 950 VE R

911 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 950 VRME R
955 966 921 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 960 VE R

921 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 960 VRME R
975 1025 910 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 R 1000 VL R

910 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 V 1000 VL V
965 1015 910 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 R 1000 VA R

910 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 V 1000 VA V
7.1
966 977 932 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 970 VE R
932 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 970 VRME R
977 988 942 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 980 VE R

942 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 980 VRME R
988 999 953 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 990 VE R

953 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 990 VRME R
999 1 010 963 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 1000 VE R

963 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 1000 VRME R
1 010 1 025 973 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 1020 VE R

973 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 1020 VRME R
1 025 1 075 955 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 R 1050 VL R

955 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 V 1050 VL V
1 015 1 065 955 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 R 1050 VA R
d1 1 025 – 1 515 mm
B1
d D1 d1 D
b1

d1 d b1 b c D1 D B1
over incl. max min
mm – –
1 025 1 045 990 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 1040 VE R

990 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 1040 VRME R
1 045 1 065 1 008 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 1060 VE R

1 008 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 1060 VRME R
1 075 1 125 1 000 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 R 1100 VL R

1 000 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 V 1100 VL V
1 065 1 115 1 000 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 R 1100 VA R
1 065 1 085 1 027 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 1080 VE R

1 027 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 1080 VRME R
1 085 1 105 1 045 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 1100 VE R

1 045 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 1100 VRME R
1 105 1 125 1 065 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 1120 VE R

1 065 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 1120 VRME R
1 125 1 175 1 045 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 R 1150 VL R

1 045 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 V 1150 VL V
1 115 1 165 1 045 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 R 1150 VA R
1 125 1 145 1 084 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 1140 VE R

1 084 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 1140 VRME R
1 145 1 165 1 103 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 1160 VE R

1 103 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 1160 VRME R
1 175 1 225 1 090 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 R 1200 VL R

1 090 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 V 1200 VL V
1 165 1 215 1 090 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 R 1200 VA R
1 165 1 185 1 121 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 1180 VE R

1 121 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 1180 VRME R
1 185 1 205 1 139 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 1200 VE R

1 139 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 1200 VRME R

d1 d b1 b c D1 D B1
over incl. max min
mm – –
1 205 1 225 1 157 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 1220 VE R

1 157 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 1220 VRME R
1 225 1 275 1 135 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 R 1250 VL R

1 135 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 V 1250 VL V
1 215 1 270 1 135 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 R 1250 VA R
1 225 1 245 1 176 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 1240 VE R

1 176 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 1240 VRME R
1 245 1 270 1 195 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 1260 VE R

1 195 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 1260 VRME R
1 270 1 295 1 218 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 1280 VE R

1 218 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 1280 VRME R
1 275 1 325 1 180 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 R 1300 VL R

1 180 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 V 1300 VL V
1 270 1 320 1 180 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 R 1300 VA R
1 295 1 315 1 240 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 1300 VE R

1 240 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 1300 VRME R
1 315 1 340 1 259 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 1325 VE R

1 259 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 1325 VRME R
1 325 1 375 1 225 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 R 1350 VL R

1 225 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 V 1350 VL V
1 320 1 370 1 225 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 R 1350 VA R
1 340 1 365 1 281 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 1350 VE R

1 281 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 1350 VRME R
1 365 1 390 1 305 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 1375 VE R

1 305 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 1375 VRME R
1 375 1 425 1 270 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 R 1400 VL R

1 270 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 V 1400 VL V
1 370 1 420 1 270 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 R 1400 VA R
1 390 1 415 1 328 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 1400 VE R

1 328 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 1400 VRME R
1 415 1 440 1 350 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 1425 VE R 7.1

1 350 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 1425 VRME R
1 425 1 475 1 315 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 R 1450 VL R

1 315 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 V 1450 VL V
1 420 1 470 1 315 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 R 1450 VA R
1 440 1 465 1 374 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 1450 VE R

1 374 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 1450 VRME R
1 465 1 490 1 397 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 1475 VE R

1 397 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 1475 VRME R
1 475 1 525 1 360 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 R 1500 VL R

1 360 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 V 1500 VL V
1 470 1 520 1 360 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 R 1500 VA R
1 490 1 515 1 419 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 1500 VE R

1 419 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 1500 VRME R
d1 1 515 – 2 020 mm
B1
d D1 d1 D
b1

d1 d b1 b c D1 D B1
over incl. max min
mm – –
1 515 1 540 1 443 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 1525 VE R

1 443 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 1525 VRME R
1 525 1 575 1 405 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 R 1550 VL R

1 405 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 V 1550 VL V
1 520 1 570 1 405 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 R 1550 VA R
1 540 1 570 1 467 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 1550 VE R

1 467 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 1550 VRME R
1 570 1 600 1 495 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 1575 VE R

1 495 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 1575 VRME R
1 575 1 625 1 450 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 R 1600 VL R

1 450 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 V 1600 VL V
1 570 1 620 1 450 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 R 1600 VA R
1 600 1 640 1 524 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 1600 VE R

1 524 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 1600 VRME R
1 625 1 675 1 495 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 R 1650 VL R

1 495 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 V 1650 VL V
1 620 1 670 1 495 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 R 1650 VA R
1 640 1 680 1 559 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 1650 VE R

1 559 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 1650 VRME R
1 675 1 725 1 540 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 R 1700 VL R

1 540 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 V 1700 VL V
1 670 1 720 1 540 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 R 1700 VA R
1 680 1 720 1 596 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 1700 VE R

1 596 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 1700 VRME R
1 725 1 775 1 585 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 R 1750 VL R

1 585 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 V 1750 VL V
1 720 1 770 1 585 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 R 1750 VA R

d1 d b1 b c D1 D B1
over incl. max min
mm – –
1 720 1 765 1 632 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 1750 VE R

1 632 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 1750 VRME R
1 765 1 810 1 671 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 1800 VE R

1 671 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 1800 VRME R
1 775 1 825 1 630 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 R 1800 VL R

1 630 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 V 1800 VL V
1 770 1 820 1 630 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 R 1800 VA R
1 810 1 855 1 714 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 1850 VE R

1 714 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 1850 VRME R
1 825 1 875 1 675 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 R 1850 VL R

1 675 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 V 1850 VL V
1 820 1 870 1 675 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 R 1850 VA R
1 855 1 905 1 753 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 1900 VE R

1 753 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 1900 VRME R
1 875 1 925 1 720 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 R 1900 VL R

1 720 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 V 1900 VL V
1 870 1 920 1 720 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 R 1900 VA R
1 905 1 955 1 794 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 1950 VE R

1 794 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 1950 VRME R
1 925 1 975 1 765 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 R 1950 VL R

1 765 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 V 1950 VL V
1 920 1 970 1 765 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 R 1950 VA R
1 955 2 010 1 844 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 R 2000 VE R

1 844 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 R 2000 VRME R
1 975 2 025 1 810 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 R 2000 VL R

1 810 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 V 2000 VL V
1 970 2 020 1 810 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 R 2000 VA R
7.1
V-ring seals – inch dimensions, globally valid outside North American market
d1 0.11 – 2.09 in.
B1
d D1 d1 D
b1

Shaft diameter Seal inside dia Nominal Seal Nominal Clearance Counter- Seal fitted code
range meter, free state seal height seat width seal width face width
d1 d c b1 b D1 (= d1 +) D (= d1 +) B1
over incl. max min
in. in. – –
0.11 0.14 0.10 0.06 0.08 0.12 0.04 0.16 0.10 ± 0.012
R 3 VA R
0.10 0.06 0.08 0.12 0.04 0.16 0.10 ± 0.012
V 3 VA V
0.14 0.18 0.13 0.08 0.09 0.15 0.04 0.24 0.12 ± 0.016
R 4 VA R
0.13 0.08 0.09 0.15 0.04 0.24 0.12 ± 0.016
V 4 VA V
0.18 0.22 0.16 0.08 0.09 0.15 0.04 0.24 0.12 ± 0.016
R 5 VA R
0.16 0.08 0.09 0.15 0.04 0.24 0.12 ± 0.016
V 5 VA V
0.16 0.08 0.15 0.20 0.04 0.24 0.18 ± 0.016
R 5 VS R
0.16 0.08 0.15 0.20 0.04 0.24 0.18 ± 0.016
V 5 VS V
0.22 0.26 0.20 0.08 0.09 0.15 0.04 0.24 0.12 ± 0.016
R 6 VA R
0.20 0.08 0.09 0.15 0.04 0.24 0.12 ± 0.016
V 6 VA V
0.20 0.08 0.15 0.20 0.04 0.24 0.18 ± 0.016
R 6 VS R
0.20 0.08 0.15 0.20 0.04 0.24 0.18 ± 0.016
V 6 VS V
0.26 0.31 0.24 0.08 0.09 0.15 0.04 0.24 0.12 ± 0.016
R 7 VA R
0.24 0.08 0.09 0.15 0.04 0.24 0.12 ± 0.016
V 7 VA V
0.24 0.08 0.15 0.20 0.04 0.24 0.18 ± 0.016
R 7 VS R
0.24 0.08 0.15 0.20 0.04 0.24 0.18 ± 0.016
V 7 VS V
0.31 0.37 0.28 0.08 0.09 0.15 0.04 0.24 0.12 ± 0.016
R 8 VA R
0.28 0.08 0.09 0.15 0.04 0.24 0.12 ± 0.016
V 8 VA V
0.28 0.08 0.15 0.20 0.04 0.24 0.18 ± 0.016
R 8 VS R
0.28 0.08 0.15 0.20 0.04 0.24 0.18 ± 0.016
V 8 VS V
0.37 0.45 0.35 0.12 0.13 0.22 0.04 0.35 0.18 ± 0.02 R 10 VA R
0.35 0.12 0.13 0.22 0.04 0.35 0.18 ± 0.02 V 10 VA V
0.35 0.12 0.22 0.30 0.04 0.35 0.26 ± 0.02 R 10 VS R
0.35 0.12 0.22 0.30 0.04 0.35 0.26 ± 0.02 V 10 VS V
0.45 0.49 0.41 0.12 0.13 0.22 0.04 0.35 0.18 ± 0.02 R 12 VA R
0.41 0.12 0.13 0.22 0.04 0.35 0.18 ± 0.02 V 12 VA V
0.45 0.53 0.41 0.12 0.22 0.30 0.04 0.35 0.26 ± 0.02 R 12 VS R
0.41 0.12 0.22 0.30 0.04 0.35 0.26 ± 0.02 V 12 VS V
0.49 0.53 0.46 0.12 0.13 0.22 0.04 0.35 0.18 ± 0.02 R 13 VA R
0.46 0.12 0.13 0.22 0.04 0.35 0.18 ± 0.02 V 13 VA V
0.53 0.61 0.49 0.12 0.13 0.22 0.04 0.35 0.18 ± 0.02 R 14 VA R
0.49 0.12 0.13 0.22 0.04 0.35 0.18 ± 0.02 V 14 VA V

d1 d c b1 b D1 (= d1 +) D (= d1 +) B1
over incl. max min
in. in. – –
0.53 0.61 0.49 0.12 0.22 0.30 0.04 0.35 0.26 ± 0.02 R 14 VS R

cont. 0.49 0.12 0.22 0.30 0.04 0.35 0.26 ± 0.02 V 14 VS V
0.61 0.67 0.55 0.12 0.13 0.22 0.04 0.35 0.18 ± 0.02 R 16 VA R
0.55 0.12 0.13 0.22 0.04 0.35 0.18 ± 0.02 V 16 VA V
0.61 0.69 0.55 0.12 0.22 0.30 0.04 0.35 0.26 ± 0.02 R 16 VS R
0.55 0.12 0.22 0.30 0.04 0.35 0.26 ± 0.02 V 16 VS V
0.69 0.75 0.63 0.12 0.13 0.22 0.04 0.35 0.18 ± 0.02 R 18 VA R
0.63 0.12 0.13 0.22 0.04 0.35 0.18 ± 0.02 V 18 VA V
0.63 0.12 0.22 0.30 0.04 0.35 0.26 ± 0.02 R 18 VS R
0.63 0.12 0.22 0.30 0.04 0.35 0.26 ± 0.02 V 18 VS V
0.75 0.83 0.71 0.16 0.19 0.30 0.08 0.47 0.24 ± 0.03 R 20 VA R
0.71 0.16 0.19 0.30 0.08 0.47 0.24 ± 0.03 V 20 VA V
0.71 0.16 0.31 0.41 0.08 0.47 0.35 ± 0.03 R 20 VS R
0.71 0.16 0.31 0.41 0.08 0.47 0.35 ± 0.03 V 20 VS V
0.83 0.94 0.79 0.16 0.19 0.30 0.08 0.47 0.24 ± 0.03 R 22 VA R
0.79 0.16 0.19 0.30 0.08 0.47 0.24 ± 0.03 V 22 VA V
0.79 0.16 0.31 0.41 0.08 0.47 0.35 ± 0.03 R 22 VS R
0.79 0.16 0.31 0.41 0.08 0.47 0.35 ± 0.03 V 22 VS V
0.94 1.06 0.87 0.16 0.19 0.30 0.08 0.47 0.24 ± 0.03 R 25 VA R
0.87 0.16 0.19 0.30 0.08 0.47 0.24 ± 0.03 V 25 VA V
0.87 0.16 0.31 0.41 0.08 0.47 0.35 ± 0.03 R 25 VS R
0.87 0.16 0.31 0.41 0.08 0.47 0.35 ± 0.03 V 25 VS V
1.06 1.14 0.98 0.16 0.19 0.30 0.08 0.47 0.24 ± 0.03 R 28 VA R
0.98 0.16 0.19 0.30 0.08 0.47 0.24 ± 0.03 V 28 VA V
0.98 0.16 0.31 0.41 0.08 0.47 0.35 ± 0.03 R 28 VS R
0.98 0.16 0.31 0.41 0.08 0.47 0.35 ± 0.03 V 28 VS V
1.14 1.22 1.06 0.16 0.19 0.30 0.08 0.47 0.24 ± 0.03 R 30 VA R
1.06 0.16 0.19 0.30 0.08 0.47 0.24 ± 0.03 V 30 VA V
1.06 0.16 0.31 0.41 0.08 0.47 0.35 ± 0.03 R 30 VS R
1.06 0.16 0.31 0.41 0.08 0.47 0.35 ± 0.03 V 30 VS V
1.22 1.30 1.14 0.16 0.19 0.30 0.08 0.47 0.24 ± 0.03 R 32 VA R
1.14 0.16 0.19 0.30 0.08 0.47 0.24 ± 0.03 V 32 VA V
1.14 0.16 0.31 0.41 0.08 0.47 0.35 ± 0.03 R 32 VS R
1.14 0.16 0.31 0.41 0.08 0.47 0.35 ± 0.03 V 32 VS V
1.30 1.42 1.22 0.16 0.19 0.30 0.08 0.47 0.24 ± 0.03 R 35 VA R
1.22 0.16 0.19 0.30 0.08 0.47 0.24 ± 0.03 V 35 VA V
1.22 0.16 0.31 0.41 0.08 0.47 0.35 ± 0.03 R 35 VS R
1.22 0.16 0.31 0.41 0.08 0.47 0.35 ± 0.03 V 35 VS V 7.1
1.42 1.50 1.34 0.16 0.19 0.30 0.08 0.47 0.24 ± 0.03 R 38 VA R
1.34 0.16 0.19 0.30 0.08 0.47 0.24 ± 0.03 V 38 VA V
1.34 0.16 0.31 0.41 0.08 0.47 0.35 ± 0.03 R 38 VS R
1.34 0.16 0.31 0.41 0.08 0.47 0.35 ± 0.03 V 38 VS V
1.50 1.69 1.42 0.20 0.22 0.35 0.08 0.59 0.28 ± 0.04 R 40 VA R
1.42 0.20 0.22 0.35 0.08 0.59 0.28 ± 0.04 V 40 VA V
1.42 0.20 0.37 0.51 0.08 0.59 0.43 ± 0.04 R 40 VS R
1.42 0.20 0.37 0.51 0.08 0.59 0.43 ± 0.04 V 40 VS V
1.69 1.89 1.57 0.20 0.22 0.35 0.08 0.59 0.28 ± 0.04 R 45 VA R
1.57 0.20 0.22 0.35 0.08 0.59 0.28 ± 0.04 V 45 VA V
1.57 0.20 0.37 0.51 0.08 0.59 0.43 ± 0.04 R 45 VS R
1.57 0.20 0.37 0.51 0.08 0.59 0.43 ± 0.04 V 45 VS V
1.89 2.09 1.77 0.20 0.22 0.35 0.08 0.59 0.28 ± 0.04 R 50 VA R
1.77 0.20 0.22 0.35 0.08 0.59 0.28 ± 0.04 V 50 VA V
1.77 0.20 0.37 0.51 0.08 0.59 0.43 ± 0.04 R 50 VS R
1.77 0.20 0.37 0.51 0.08 0.59 0.43 ± 0.04 V 50 VS V
d1 2.09 – 7.68 in.
B1
d D1 d1 D
b1

d1 d c b1 b D1 (= d1 +) D (= d1 +) B1
over incl. max min
in. in. – –
2.09 2.28 1.93 0.20 0.22 0.35 0.08 0.59 0.28 ± 0.04 R 55 VA R
1.93 0.20 0.22 0.35 0.08 0.59 0.28 ± 0.04 V 55 VA V
1.93 0.20 0.37 0.51 0.08 0.59 0.43 ± 0.04 R 55 VS R
1.93 0.20 0.37 0.51 0.08 0.59 0.43 ± 0.04 V 55 VS V
2.28 2.48 2.13 0.20 0.22 0.35 0.08 0.59 0.28 ± 0.04 R 60 VA R
2.13 0.20 0.22 0.35 0.08 0.59 0.28 ± 0.04 V 60 VA V
2.13 0.20 0.37 0.51 0.08 0.59 0.43 ± 0.04 R 60 VS R
2.13 0.20 0.37 0.51 0.08 0.59 0.43 ± 0.04 V 60 VS V
2.48 2.68 2.28 0.20 0.22 0.35 0.08 0.59 0.28 ± 0.04 R 65 VA R
2.28 0.20 0.22 0.35 0.08 0.59 0.28 ± 0.04 V 65 VA V
2.28 0.20 0.37 0.51 0.08 0.59 0.43 ± 0.04 R 65 VS R
2.28 0.20 0.37 0.51 0.08 0.59 0.43 ± 0.04 V 65 VS V
2.68 2.87 2.48 0.24 0.27 0.43 0.12 0.71 0.35 ± 0.05 R 70 VA R
2.48 0.24 0.27 0.43 0.12 0.71 0.35 ± 0.05 V 70 VA V
2.48 0.24 0.44 0.61 0.12 0.71 0.53 ± 0.05 R 70 VS R
2.48 0.24 0.44 0.61 0.12 0.71 0.53 ± 0.05 V 70 VS V
2.87 3.07 2.64 0.24 0.27 0.43 0.12 0.71 0.35 ± 0.05 R 75 VA R
2.64 0.24 0.27 0.43 0.12 0.71 0.53 ± 0.05 R 75 VS R
2.64 0.24 0.44 0.61 0.12 0.71 0.53 ± 0.05 V 75 VS V
3.07 3.27 2.83 0.24 0.27 0.43 0.12 0.71 0.35 ± 0.05 R 80 VA R
2.83 0.24 0.27 0.43 0.12 0.71 0.35 ± 0.05 V 80 VA V
2.83 0.24 0.44 0.61 0.12 0.71 0.53 ± 0.05 R 80 VS R
2.83 0.24 0.44 0.61 0.12 0.71 0.53 ± 0.05 V 80 VS V
3.27 3.46 2.99 0.24 0.27 0.43 0.12 0.71 0.35 ± 0.05 R 85 VA R
2.99 0.24 0.27 0.43 0.12 0.71 0.35 ± 0.05 V 85 VA V
2.99 0.24 0.44 0.61 0.12 0.71 0.53 ± 0.05 R 85 VS R
2.99 0.24 0.44 0.61 0.12 0.71 0.53 ± 0.05 V 85 VS V
3.46 3.66 3.19 0.24 0.27 0.43 0.12 0.71 0.35 ± 0.05 R 90 VA R
3.19 0.24 0.27 0.43 0.12 0.71 0.35 ± 0.05 V 90 VA V
3.19 0.24 0.44 0.61 0.12 0.71 0.53 ± 0.05 R 90 VS R
3.19 0.24 0.44 0.61 0.12 0.71 0.53 ± 0.05 V 90 VS V
3.66 3.86 3.35 0.24 0.27 0.43 0.12 0.71 0.35 ± 0.05 R 95 VA R
3.35 0.24 0.27 0.43 0.12 0.71 0.35 ± 0.05 V 95 VA V
3.35 0.24 0.44 0.61 0.12 0.71 0.53 ± 0.05 R 95 VS R
3.35 0.24 0.44 0.61 0.12 0.71 0.53 ± 0.05 V 95 VS V

d1 d c b1 b D1 (= d1 +) D (= d1 +) B1
over incl. max min
in. in. – –
3.86 4.13 3.54 0.24 0.27 0.43 0.12 0.71 0.35 ± 0.05 R 100 VA R
3.54 0.24 0.27 0.43 0.12 0.71 0.35 ± 0.05 V 100 VA V
3.54 0.24 0.44 0.61 0.12 0.71 0.53 ± 0.05 R 100 VS R
3.54 0.24 0.44 0.61 0.12 0.71 0.53 ± 0.05 V 100 VS V
4.13 4.53 3.90 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 R 110 VL R
3.90 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 V 110 VL V
3.90 0.28 0.31 0.50 0.16 0.83 0.41 ± 0.06 R 110 VA R
3.90 0.28 0.31 0.50 0.16 0.83 0.41 ± 0.06 V 110 VA V
3.90 0.28 0.52 0.71 0.16 0.83 0.61 ± 0.06 R 110 VS R
3.90 0.28 0.52 0.71 0.16 0.83 0.61 ± 0.06 V 110 VS V
4.53 4.92 4.25 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 R 120 VL R
4.25 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 V 120 VL V
4.25 0.28 0.31 0.50 0.16 0.83 0.41 ± 0.06 R 120 VA R
4.25 0.28 0.31 0.50 0.16 0.83 0.41 ± 0.06 V 120 VA V
4.25 0.28 0.52 0.71 0.16 0.83 0.61 ± 0.06 R 120 VS R
4.25 0.28 0.52 0.71 0.16 0.83 0.61 ± 0.06 V 120 VS V
4.92 5.31 4.61 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 R 130 VL R
4.61 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 V 130 VL V
4.61 0.28 0.31 0.50 0.16 0.83 0.41 ± 0.06 R 130 VA R
4.61 0.28 0.31 0.50 0.16 0.83 0.41 ± 0.06 V 130 VA V
4.61 0.28 0.52 0.71 0.16 0.83 0.61 ± 0.06 R 130 VS R
4.61 0.28 0.52 0.71 0.16 0.83 0.61 ± 0.06 V 130 VS V
5.31 5.71 4.96 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 R 140 VL R
4.96 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 V 140 VL V
4.96 0.28 0.31 0.50 0.16 0.83 0.41 ± 0.06 R 140 VA R
4.96 0.28 0.31 0.50 0.16 0.83 0.41 ± 0.06 V 140 VA V
4.96 0.28 0.52 0.71 0.16 0.83 0.61 ± 0.06 R 140 VS R
4.96 0.28 0.52 0.71 0.16 0.83 0.61 ± 0.06 V 140 VS V
5.71 6.10 5.31 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 R 150 VL R
5.31 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 V 150 VL V
5.31 0.28 0.31 0.50 0.16 0.83 0.41 ± 0.06 R 150 VA R
5.31 0.28 0.31 0.50 0.16 0.83 0.41 ± 0.06 V 150 VA V
5.31 0.28 0.52 0.71 0.16 0.83 0.61 ± 0.06 R 150 VS R
5.31 0.28 0.52 0.71 0.16 0.83 0.61 ± 0.06 V 150 VS V
6.10 6.50 5.67 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 R 160 VL R
5.67 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 V 160 VL V
5.67 0.31 0.35 0.57 0.16 0.94 0.47 ± 0.07 R 160 VA R
5.67 0.31 0.35 0.57 0.16 0.94 0.47 ± 0.07 V 160 VA V
5.67 0.31 0.59 0.81 0.16 0.94 0.71 ± 0.07 R 160 VS R
5.67 0.31 0.59 0.81 0.16 0.94 0.71 ± 0.07 V 160 VS V
6.50 6.89 6.02 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 R 170 VL R 7.1
6.02 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 V 170 VL V
6.02 0.31 0.35 0.57 0.16 0.94 0.47 ± 0.07 R 170 VA R
6.02 0.31 0.35 0.57 0.16 0.94 0.47 ± 0.07 V 170 VA V
6.02 0.31 0.59 0.81 0.16 0.94 0.71 ± 0.07 R 170 VS R
6.02 0.31 0.59 0.81 0.16 0.94 0.71 ± 0.07 V 170 VS V
6.89 7.28 6.38 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 R 180 VL R
6.38 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 V 180 VL V
6.38 0.31 0.35 0.57 0.16 0.94 0.47 ± 0.07 R 180 VA R
6.38 0.31 0.35 0.57 0.16 0.94 0.47 ± 0.07 V 180 VA V
6.38 0.31 0.59 0.81 0.16 0.94 0.71 ± 0.07 R 180 VS R
6.38 0.31 0.59 0.81 0.16 0.94 0.71 ± 0.07 V 180 VS V
7.28 7.68 6.73 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 R 190 VL R
6.73 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 V 190 VL V
6.73 0.31 0.35 0.57 0.16 0.94 0.47 ± 0.07 R 190 VA R
6.73 0.31 0.35 0.57 0.16 0.94 0.47 ± 0.07 V 190 VA V
6.73 0.31 0.59 0.81 0.16 0.94 0.71 ± 0.07 R 190 VS R
6.73 0.31 0.59 0.81 0.16 0.94 0.71 ± 0.07 V 190 VS V
d1 7.48 – 15.55 in.
B1
d D1 d1 D
b1

d1 d c b1 b D1 (= d1 +) D (= d1 +) B1
over incl. max min
in. in. – –
7.68 8.27 7.17 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 R 200 VL R
7.17 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 V 200 VL V
7.09 0.31 0.35 0.57 0.16 0.94 0.47 ± 0.07 R 199 VA R
7.09 0.31 0.35 0.57 0.16 0.94 0.47 ± 0.07 V 199 VA V
7.09 0.31 0.59 0.81 0.16 0.94 0.71 ± 0.07 R 199 VS R
7.09 0.31 0.59 0.81 0.16 0.94 0.71 ± 0.07 V 199 VS V
7.48 8.27 7.09 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 R 200 VA R
7.09 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 V 200 VA V
8.27 9.17 7.80 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 R 220 VL R
7.80 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 V 220 VL V
7.80 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 R 220 VA R
7.80 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 V 220 VA V
9.17 10.24 8.86 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 R 250 VL R
8.86 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 V 250 VL V
9.25 10.43 8.86 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 R 250 VA R
8.86 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 V 250 VA V
10.24 11.22 9.72 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 R 275 VL R
9.72 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 V 275 VL V
10.43 11.42 9.72 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 R 275 VA R
9.72 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 V 275 VA V
11.22 12.20 10.63 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 R 300 VL R
10.63 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 V 300 VL V
11.42 12.20 10.63 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 R 300 VA R
10.63 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 V 300 VA V
11.81 12.01 11.57 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 300 VE R
11.57 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 300 VRME R
12.01 12.20 11.77 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 305 VE R
11.77 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 305 VRME R
12.20 13.19 11.50 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 R 325 VL R
11.50 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 V 325 VL V
11.50 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 R 325 VA R

d1 d c b1 b D1 (= d1 +) D (= d1 +) B1
over incl. max min
in. in. – –
12.20 13.19 11.50 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 V 325 VA V

cont. 11.97 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 310 VE R
11.97 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 310 VRME R
12.40 12.60 12.17 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 315 VE R
12.17 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 315 VRME R
12.60 12.80 12.36 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 320 VE R
12.36 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 320 VRME R
12.80 12.99 12.56 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 325 VE R
12.56 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 325 VRME R
12.99 13.19 12.72 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 330 VE R
12.72 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 330 VRME R
13.19 14.37 12.40 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 R 350 VL R
12.40 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 V 350 VL V
12.40 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 R 350 VA R
12.40 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 V 350 VA V
13.19 13.39 12.91 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 335 VE R
12.91 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 335 VRME R
13.39 13.58 13.11 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 340 VE R
12.91 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 340 VRME R
13.58 13.78 13.31 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 345 VE R
13.31 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 345 VRME R
13.78 13.98 13.50 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 350 VE R
13.50 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 350 VRME R
13.98 14.17 13.66 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 355 VE R
13.66 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 355 VRME R
14.17 14.37 13.86 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 360 VE R
14.06 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 360 VRME R
14.37 15.16 13.27 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 R 375 VL R
13.27 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 V 375 VL V
14.37 15.35 13.27 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 R 375 VA R
13.27 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 V 375 VA V
14.37 14.57 14.06 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 365 VE R
14.57 14.76 14.25 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 370 VE R 7.1
14.25 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 370 VRME R
14.76 14.96 14.45 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 375 VE R
14.45 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 375 VRME R
14.96 15.16 14.61 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 380 VE R
14.61 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 380 VRME R
15.16 16.14 14.17 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 R 400 VL R
14.17 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 V 400 VL V
15.35 16.93 14.17 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 R 400 VA R
14.17 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 V 400 VA V
15.16 15.35 14.80 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 385 VE R
14.80 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 385 VRME R
15.35 15.55 15.00 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 390 VE R
15.00 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 390 VRME R
d1 15.55 – 21.26 in.
B1
d D1 d1 D
b1

d1 d c b1 b D1 (= d1 +) D (= d1 +) B1
over incl. max min
in. in. – –
15.55 15.75 15.20 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 395 VE R
15.20 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 395 VRME R
15.75 15.94 15.39 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 400 VE R
15.39 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 400 VRME R
15.94 16.14 15.59 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 405 VE R
15.59 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 405 VRME R
16.14 16.34 15.79 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 410 VE R
15.79 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 410 VRME R
16.34 16.54 15.94 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 415 VE R
15.94 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 415 VRME R
16.54 16.73 16.14 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 420 VE R
16.14 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 420 VRME R
16.73 16.93 16.34 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 425 VE R
16.34 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 425 VRME R
16.14 17.32 15.04 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 R 425 VL R
15.04 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 V 425 VL V
17.32 18.70 15.94 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 R 450 VL R
15.94 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 V 450 VL V
16.93 18.90 15.94 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 R 450 VA R
15.94 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 V 450 VA V
16.93 17.13 16.54 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 430 VE R
16.54 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 430 VRME R
17.13 17.32 16.73 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 435 VE R
16.73 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 435 VRME R
17.32 17.52 16.89 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 440 VE R
16.89 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 440 VRME R
17.52 17.72 17.09 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 445 VE R
17.09 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 445 VRME R

d1 d c b1 b D1 (= d1 +) D (= d1 +) B1
over incl. max min
in. in. – –
17.72 17.91 17.28 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 450 VE R
17.28 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 450 VRME R
17.91 18.11 17.48 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 455 VE R
17.48 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 455 VRME R
18.11 18.31 17.64 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 460 VE R
17.64 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 460 VRME R
18.31 18.50 17.83 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 465 VE R
17.83 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 465 VRME R
18.50 18.70 18.03 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 470 VE R
18.03 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 470 VRME R
18.70 18.90 18.23 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 475 VE R
18.23 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 475 VRME R
18.70 20.08 17.72 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 R 500 VL R
17.72 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 V 500 VL V
20.08 21.26 18.58 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 R 525 VL R
18.58 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 V 525 VL V
18.90 20.87 17.72 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 R 500 VA R
17.72 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 V 500 VA V
18.90 19.09 18.43 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 480 VE R
18.43 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 480 VRME R
19.09 19.29 18.62 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 485 VE R
18.62 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 485 VRME R
19.29 19.49 18.82 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 490 VE R
18.82 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 490 VRME R
19.49 19.69 19.02 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 495 VE R
19.02 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 495 VRME R
19.69 19.88 19.21 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 500 VE R
19.21 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 500 VRME R
19.88 20.08 19.41 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 505 VE R
19.41 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 505 VRME R
20.08 20.28 19.57 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 510 VE R
19.57 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 510 VRME R
7.1
20.28 20.47 19.76 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 515 VE R
19.76 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 515 VRME R
20.47 20.67 19.96 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 520 VE R
19.96 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 520 VRME R
20.67 20.87 20.16 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 525 VE R
20.16 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 525 VRME R
21.26 22.64 19.49 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 R 550 VL R
19.49 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 V 550 VL V
20.87 22.83 19.49 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 R 550 VA R
19.49 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 V 550 VA V
20.87 21.06 20.35 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 530 VE R
20.35 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 530 VRME R
21.06 21.26 20.51 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 535 VE R
20.51 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 535 VRME R
d1 21.26 – 29.84 in.
B1
d D1 d1 D
b1

d1 d c b1 b D1 (= d1 +) D (= d1 +) B1
over incl. max min
in. in. – –
21.26 21.46 20.71 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 540 VE R
20.71 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 540 VRME R
21.46 21.65 20.91 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 545 VE R
20.91 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 545 VRME R
21.65 21.85 21.10 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 550 VE R
21.10 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 550 VRME R
21.85 22.05 21.30 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 555 VE R
21.30 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 555 VRME R
22.05 22.24 21.50 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 560 VE R
21.50 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 560 VRME R
22.24 22.44 21.65 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 565 VE R
21.65 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 565 VRME R
22.44 22.64 21.85 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 570 VE R
21.85 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 570 VRME R
22.64 22.83 22.05 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 575 VE R
22.05 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 575 VRME R
22.64 24.61 21.26 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 R 600 VL R
21.26 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 V 600 VL V
22.83 24.80 21.26 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 R 600 VA R
21.26 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 V 600 VA V
22.83 23.03 22.24 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 580 VE R
22.24 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 580 VRME R
23.03 23.23 22.44 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 585 VE R
22.44 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 585 VRME R
23.23 23.62 22.64 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 590 VE R
22.64 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 590 VRME R
23.62 24.02 22.91 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 600 VE R
22.91 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 600 VRME R

d1 d c b1 b D1 (= d1 +) D (= d1 +) B1
over incl. max min
in. in. – –
24.02 24.41 23.31 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 610 VE R
23.31 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 610 VRME R
24.41 24.80 23.70 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 620 VE R
23.70 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 620 VRME R
24.21 26.57 23.62 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 R 650 VL R
23.62 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 V 650 VL V
24.80 26.18 23.62 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 R 650 VA R
23.62 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 V 650 VA V
24.80 25.20 24.09 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 630 VE R
24.09 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 630 VRME R
25.20 25.59 24.45 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 640 VE R
24.45 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 640 VRME R
25.59 25.98 24.84 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 650 VE R
24.84 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 650 VRME R
25.98 26.38 25.20 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 660 VE R
25.20 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 660 VRME R
26.57 27.95 24.80 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 R 700 VL R
24.80 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 V 700 VL V
26.18 27.76 24.80 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 R 700 VA R
24.80 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 V 700 VA V
26.38 26.77 25.59 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 670 VE R
25.59 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 670 VRME R
26.77 27.17 25.98 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 680 VE R
25.98 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 680 VRME R
27.17 27.56 26.38 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 690 VE R
26.38 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 690 VRME R
27.56 27.95 26.77 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 700 VE R
26.77 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 700 VRME R
27.95 29.13 26.38 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 R 725 VL R
26.38 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 V 725 VL V
27.76 29.33 26.38 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 R 725 VA R
26.38 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 V 725 VA V
7.1
27.95 28.35 27.13 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 710 VE R
27.13 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 710 VRME R
28.35 28.74 27.52 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 720 VE R
27.52 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 720 VRME R
28.74 29.13 27.91 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 730 VE R
27.91 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 730 VRME R
29.13 29.53 28.27 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 740 VE R
28.27 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 740 VRME R
29.13 30.51 27.76 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 R 750 VL R
27.76 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 V 750 VL V
29.33 30.91 27.76 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 R 750 VA R
27.76 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 V 750 VA V
29.53 29.84 28.66 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 750 VE R
28.66 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 750 VRME R
d1 29.84 – 41.93 in.
B1
d D1 d1 D
b1

d1 d c b1 b D1 (= d1 +) D (= d1 +) B1
over incl. max min
in. in. – –
29.84 30.16 28.94 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 760 VE R
28.94 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 760 VRME R
30.16 30.47 29.25 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 770 VE R
29.25 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 770 VRME R
30.47 30.83 29.57 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 780 VE R
29.57 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 780 VRME R
30.83 31.18 29.88 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 790 VE R
29.88 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 790 VRME R
30.51 32.48 29.33 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 R 800 VL R
29.33 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 V 800 VL V
30.91 32.68 29.33 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 R 800 VA R
29.33 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 V 800 VA V
31.18 31.54 30.24 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 800 VE R
30.24 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 800 VRME R
31.54 31.89 30.59 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 810 VE R
30.59 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 810 VRME R
31.89 32.32 30.94 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 820 VE R
30.94 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 820 VRME R
32.32 32.72 31.34 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 830 VE R
31.34 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 830 VRME R
32.48 34.45 30.91 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 R 850 VL R
30.91 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 V 850 VL V
32.68 34.45 30.91 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 R 850 VA R
30.91 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 V 850 VA V
32.72 33.11 31.69 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 840 VE R
31.69 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 840 VRME R
33.11 33.50 32.05 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 850 VE R
32.05 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 850 VRME R

d1 d c b1 b D1 (= d1 +) D (= d1 +) B1
over incl. max min
in. in. – –
33.50 33.90 32.44 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 860 VE R
32.44 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 860 VRME R
33.90 34.29 32.80 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 870 VE R
32.80 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 870 VRME R
34.29 34.72 33.19 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 880 VE R
33.19 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 880 VRME R
34.45 36.42 32.48 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 R 900 VL R
32.48 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 V 900 VL V
34.45 36.22 32.48 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 R 900 VA R
32.48 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 V 900 VA V
34.72 35.12 33.58 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 890 VE R
33.58 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 890 VRME R
35.12 35.91 34.29 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 900 VE R
34.29 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 900 VRME R
35.91 36.30 34.65 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 920 VE R
34.65 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 920 VRME R
36.42 38.39 34.06 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 R 950 VL R
34.06 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 V 950 VL V
36.22 37.99 34.06 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 R 950 VA R
34.06 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 V 950 VA V
36.30 36.73 35.04 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 930 VE R
35.04 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 930 VRME R
36.73 37.17 35.43 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 940 VE R
35.43 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 940 VRME R
37.17 37.60 35.87 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 950 VE R
35.87 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 950 VRME R
37.60 38.03 36.26 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 960 VE R
36.26 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 960 VRME R
38.39 40.35 35.83 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 R 1000 VL R
35.83 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 V 1000 VL V
37.99 39.96 35.83 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 R 1000 VA R
35.83 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 V 1000 VA V
7.1
38.03 38.46 36.69 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 970 VE R
36.69 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 970 VRME R
38.46 38.90 37.09 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 980 VE R
37.09 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 980 VRME R
38.90 39.33 37.52 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 990 VE R
37.52 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 990 VRME R
39.33 39.76 37.91 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1000 VE R
37.91 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1000 VRME R
39.76 40.35 38.31 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1020 VE R
38.31 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1020 VRME R
40.35 42.32 37.60 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 R 1050 VL R
37.60 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 V 1050 VL V
39.96 41.93 37.60 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 R 1050 VA R
d1 40.35 – 59.65 in.
B1
d D1 d1 D
b1

d1 d c b1 b D1 (= d1 +) D (= d1 +) B1
over incl. max min
in. in. – –
40.35 41.14 38.98 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1040 VE R
38.98 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1040 VRME R
41.14 41.93 39.69 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1060 VE R
39.69 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1060 VRME R
42.32 44.29 39.37 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 R 1100 VL R
39.37 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 V 1100 VL V
41.93 43.90 39.37 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 R 1100 VA R
40.43 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1080 VE R
41.93 42.72 40.43 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1080 VRME R
42.72 43.50 41.14 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1100 VE R
41.14 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1100 VRME R
43.50 44.29 41.93 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1120 VE R
41.93 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1120 VRME R
44.29 46.26 41.14 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 R 1150 VL R
41.14 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 V 1150 VL V
43.90 45.87 41.14 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 R 1150 VA R
44.29 45.08 42.68 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1140 VE R
42.68 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1140 VRME R
45.08 45.87 43.43 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1160 VE R
43.43 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1160 VRME R
46.26 48.23 42.91 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 R 1200 VL R
42.91 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 V 1200 VL V
45.87 47.83 42.91 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 R 1200 VA R
45.87 46.65 44.13 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1180 VE R
44.13 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1180 VRME R
46.65 47.44 44.84 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1200 VE R
44.84 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1200 VRME R

d1 d c b1 b D1 (= d1 +) D (= d1 +) B1
over incl. max min
in. in. – –
47.44 48.23 45.55 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1220 VE R
45.55 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1220 VRME R
48.23 50.20 44.69 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 R 1250 VL R
44.69 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 V 1250 VL V
47.83 50.00 44.69 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 R 1250 VA R
48.23 49.02 46.30 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1240 VE R
46.30 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1240 VRME R
49.02 50.00 47.05 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1260 VE R
47.05 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1260 VRME R
50.00 50.98 47.95 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1280 VE R
47.95 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1280 VRME R
50.20 52.17 46.46 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 R 1300 VL R
46.46 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 V 1300 VL V
50.00 51.97 46.46 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 R 1300 VA R
50.98 51.77 48.82 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1300 VE R
48.82 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1300 VRME R
51.77 52.76 49.57 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1325 VE R
49.57 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1325 VRME R
52.17 54.13 48.23 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 R 1350 VL R
48.23 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 V 1350 VL V
51.97 53.94 48.23 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 R 1350 VA R
52.76 53.74 50.43 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1350 VE R
50.43 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1350 VRME R
53.74 54.72 51.38 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1375 VE R
51.38 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1375 VRME R
54.13 56.10 50.00 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 R 1400 VL R
50.00 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 V 1400 VL V
53.94 55.91 50.00 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 R 1400 VA R
54.72 55.71 52.28 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1400 VE R
52.28 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1400 VRME R
55.71 56.69 53.15 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1425 VE R 7.1
53.15 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1425 VRME R
56.10 58.07 51.77 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 R 1450 VL R
51.77 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 V 1450 VL V
55.91 57.87 51.77 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 R 1450 VA R
56.69 57.68 54.09 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1450 VE R
54.09 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1450 VRME R
57.68 58.66 55.00 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1475 VE R
55.00 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1475 VRME R
58.07 60.04 53.54 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 R 1500 VL R
53.54 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 V 1500 VL V
57.87 59.84 53.54 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 R 1500 VA R
58.66 59.65 55.87 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1500 VE R
55.87 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1500 VRME R
d1 59.65 – 79.53 in.
B1
d D1 d1 D
b1

d1 d c b1 b D1 (= d1 +) D (= d1 +) B1
over incl. max min
in. in. – –
59.65 60.63 56.81 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1525 VE R
56.81 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1525 VRME R
60.04 62.01 55.31 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 R 1550 VL R
55.31 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 V 1550 VL V
59.84 61.81 55.31 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 R 1550 VA R
60.63 61.81 57.76 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1550 VE R
57.76 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1550 VRME R
61.81 62.99 58.86 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1575 VE R
58.86 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1575 VRME R
62.01 63.98 57.09 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 R 1600 VL R
57.09 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 V 1600 VL V
61.81 63.78 57.09 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 R 1600 VA R
62.99 64.57 60.00 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1600 VE R
60.00 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1600 VRME R
63.98 65.94 58.86 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 R 1650 VL R
58.86 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 V 1650 VL V
63.78 65.75 58.86 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 R 1650 VA R
64.57 66.14 61.38 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1650 VE R
61.38 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1650 VRME R
65.94 67.91 60.63 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 R 1700 VL R
60.63 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 V 1700 VL V
65.75 67.72 60.63 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 R 1700 VA R
66.14 67.72 62.83 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1700 VE R
62.83 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1700 VRME R
67.91 69.88 62.40 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 R 1750 VL R
62.40 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 V 1750 VL V

d1 d c b1 b D1 (= d1 +) D (= d1 +) B1
over incl. max min
in. in. – –
67.72 69.69 62.40 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 R 1750 VA R
67.72 69.49 64.25 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1750 VE R
64.25 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1750 VRME R
69.49 71.26 65.79 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1800 VE R
65.79 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1800 VRME R
69.88 71.85 64.17 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 R 1800 VL R
64.17 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 V 1800 VL V
69.69 71.65 64.17 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 R 1800 VA R
71.26 73.03 67.48 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1850 VE R
67.48 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1850 VRME R
71.85 73.82 65.94 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 R 1850 VL R
65.94 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 V 1850 VL V
71.65 73.62 65.94 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 R 1850 VA R
73.03 75.00 69.02 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1900 VE R
69.02 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1900 VRME R
73.82 75.79 67.72 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 R 1900 VL R
67.72 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 V 1900 VL V
73.62 75.59 67.72 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 R 1900 VA R
75.00 76.97 70.63 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1950 VE R
70.63 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 1950 VRME R
75.79 77.76 69.49 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 R 1950 VL R
75.79 77.76 69.49 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 V 1950 VL V
69.49 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 R 1950 VA R
76.97 79.13 72.60 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 2000 VE R
72.60 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 R 2000 VRME R
77.76 79.72 71.26 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 R 2000 VL R
71.26 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 V 2000 VL V
77.56 79.53 71.26 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 R 2000 VA R

7.1
V-ring seals – metric dimensions, for North American market

d1 2,7 – 53 mm
B1
d D1 d1 D
b1

d1 d b1 b c D1 D B1
over incl. max min
mm – – –
2,7 3,5 2,5 2,1 3 1,5 d1 + 1 d1 + 4 2,5 ± 0,3 VR1 R 400030
2,5 2,1 3 1,5 d1 + 1 d1 + 4 2,5 ± 0,3 VR1 V 400034
3,5 4,5 3,2 2,4 3,7 2 d1 + 1 d1 + 6 3 ± 0,4 VR1 R 400040
3,2 2,4 3,7 2 d1 + 1 d1 + 6 3 ± 0,4 VR1 V 400044
4,5 5,5 4 2,4 3,7 2 d1 + 1 d1 + 6 3 ± 0,4 VR1 R 400050

4 2,4 3,7 2 d1 + 1 d1 + 6 3 ± 0,4 VR1 V 400054
4 3,9 5,2 2 d1 + 1 d1 + 6 4,5 ± 0,4 VR2 R 400051
4 3,9 5,2 2 d1 + 1 d1 + 6 4,5 ± 0,4 VR2 V 400055
5,5 6,5 5 2,4 3,7 2 d1 + 1 d1 + 6 3 ± 0,4 VR1 R 400060

5 2,4 3,7 2 d1 + 1 d1 + 6 3 ± 0,4 VR1 V 400064
5 3,9 5,2 2 d1 + 1 d1 + 6 4,5 ± 0,4 VR2 R 400061
5 3,9 5,2 2 d1 + 1 d1 + 6 4,5 ± 0,4 VR2 V 400065
6,5 8 6 2,4 3,7 2 d1 + 1 d1 + 6 3 ± 0,4 VR1 R 400070

6 2,4 3,7 2 d1 + 1 d1 + 6 3 ± 0,4 VR1 V 400074
6 3,9 5,2 2 d1 + 1 d1 + 6 4,5 ± 0,4 VR2 R 400071
6 3,9 5,2 2 d1 + 1 d1 + 6 4,5 ± 0,4 VR2 V 400075
8 9,5 7 2,4 3,7 2 d1 + 1 d1 + 6 3 ± 0,4 VR1 R 400080

7 2,4 3,7 2 d1 + 1 d1 + 6 3 ± 0,4 VR1 V 400084
7 3,9 5,2 2 d1 + 1 d1 + 6 4,5 ± 0,4 VR2 R 400081
7 3,9 5,2 2 d1 + 1 d1 + 6 4,5 ± 0,4 VR2 V 400085
9,5 11,5 9 3,4 5,5 3 d1 + 1 d1 + 9 4,5 ± 0,6 VR1 R 400100
9 3,4 5,5 3 d1 + 1 d1 + 9 4,5 ± 0,6 VR1 V 400104
9 5,6 7,7 3 d1 + 1 d1 + 9 6,7 ± 0,6 VR2 R 400101
9 5,6 7,7 3 d1 + 1 d1 + 9 6,7 ± 0,6 VR2 V 400105
11,5 12,5 10,5 3,4 5,5 3 d1 + 1 d1 + 9 4,5 ± 0,6 VR1 R 400120
10,5 3,4 5,5 3 d1 + 1 d1 + 9 4,5 ± 0,6 VR1 V 400124
10,5 5,6 7,7 3 d1 + 1 d1 + 9 6,7 ± 0,6 VR2 R 400121
10,5 5,6 7,7 3 d1 + 1 d1 + 9 6,7 ± 0,6 VR2 V 400125
12,5 13,5 11,7 3,4 5,5 3 d1 + 1 d1 + 9 4,5 ± 0,6 VR1 R 400130
11,7 3,4 5,5 3 d1 + 1 d1 + 9 4,5 ± 0,6 VR1 V 400134
13,5 15,5 12,5 3,4 5,5 3 d1 + 1 d1 + 9 4,5 ± 0,6 VR1 R 400140
12,5 3,4 5,5 3 d1 + 1 d1 + 9 4,5 ± 0,6 VR1 V 400144

d1 d b1 b c D1 D B1
over incl. max min
mm – – –
13,5 15,5 12,5 5,6 7,7 3 d1 + 1 d1 + 9 6,7 ± 0,6 VR2 R 400141

cont. 12,5 5,6 7,7 3 d1 + 1 d1 + 9 6,7 ± 0,6 VR2 V 400145
15,5 17 14 3,4 5,5 3 d1 + 1 d1 + 9 4,5 ± 0,6 VR1 R 400160

14 3,4 5,5 3 d1 + 1 d1 + 9 4,5 ± 0,6 VR1 V 400164
15,5 17,5 14 5,6 7,7 3 d1 + 1 d1 + 9 6,7 ± 0,6 VR2 R 400161
14 5,6 7,7 3 d1 + 1 d1 + 9 6,7 ± 0,6 VR2 V 400165
17,5 19 16 3,4 5,5 3 d1 + 1 d1 + 9 4,5 ± 0,6 VR1 R 400180

16 3,4 5,5 3 d1 + 1 d1 + 9 4,5 ± 0,6 VR1 V 400184
16 5,6 7,7 3 d1 + 1 d1 + 9 6,7 ± 0,6 VR2 R 400181
16 5,6 7,7 3 d1 + 1 d1 + 9 6,7 ± 0,6 VR2 V 400185
19 21 18 4,7 7,5 4 d1 + 2 d1 + 12 6 ± 0,8 VR1 R 400200

18 4,7 7,5 4 d1 + 2 d1 + 12 6 ± 0,8 VR1 V 400204
18 7,9 10,5 4 d1 + 2 d1 + 12 9 ± 0,8 VR2 R 400201
18 7,9 10,5 4 d1 + 2 d1 + 12 9 ± 0,8 VR2 V 400205
21 24 20 4,7 7,5 4 d1 + 2 d1 + 12 6 ± 0,8 VR1 R 400220

20 4,7 7,5 4 d1 + 2 d1 + 12 6 ± 0,8 VR1 V 400224
20 7,9 10,5 4 d1 + 2 d1 + 12 9 ± 0,8 VR2 R 400221
20 7,9 10,5 4 d1 + 2 d1 + 12 9 ± 0,8 VR2 V 400225
24 27 22 4,7 7,5 4 d1 + 2 d1 + 12 6 ± 0,8 VR1 R 400250

22 4,7 7,5 4 d1 + 2 d1 + 12 6 ± 0,8 VR1 V 400254
22 7,9 10,5 4 d1 + 2 d1 + 12 9 ± 0,8 VR2 R 400251
22 7,9 10,5 4 d1 + 2 d1 + 12 9 ± 0,8 VR2 V 400255
27 29 25 4,7 7,5 4 d1 + 2 12 6 ± 0,8 VR1 R 400280

25 4,7 7,5 4 d1 + 2 d1 + 12 6 ± 0,8 VR1 V 400284
25 7,9 10,5 4 d1 + 2 d1 + 12 9 ± 0,8 VR2 R 400281
25 7,9 10,5 4 d1 + 2 d1 + 12 9 ± 0,8 VR2 V 400285
29 31 27 4,7 7,5 4 d1 + 2 d1 + 12 6 ± 0,8 VR1 R 400300

27 4,7 7,5 4 d1 + 2 d1 + 12 6 ± 0,8 VR1 V 400304
27 7,9 10,5 4 d1 + 2 d1 + 12 9 ± 0,8 VR2 R 400301
27 7,9 10,5 4 d1 + 2 d1 + 12 9 ± 0,8 VR2 V 400305
31 33 29 4,7 7,5 4 d1 + 2 d1 + 12 6 ± 0,8 VR1 R 400320

29 4,7 7,5 4 d1 + 2 d1 + 12 6 ± 0,8 VR1 V 400324
29 7,9 10,5 4 d1 + 2 d1 + 12 9 ± 0,8 VR2 R 400321
29 7,9 10,5 4 d1 + 2 d1 + 12 9 ± 0,8 VR2 V 400325
33 36 31 4,7 7,5 4 d1 + 2 d1 + 12 6 ± 0,8 VR1 R 400350

31 4,7 7,5 4 d1 + 2 d1 + 12 6 ± 0,8 VR1 V 400354
31 7,9 10,5 4 d1 + 2 d1 + 12 9 ± 0,8 VR2 R 400351
31 7,9 10,5 4 d1 + 2 d1 + 12 9 ± 0,8 VR2 V 400355 7.2
36 38 34 4,7 7,5 4 d1 + 2 d1 + 12 6 ± 0,8 VR1 R 400380
34 4,7 7,5 4 d1 + 2 d1 + 12 6 ± 0,8 VR1 V 400384
34 7,9 10,5 4 d1 + 2 d1 + 12 9 ± 0,8 VR2 R 400381
34 7,9 10,5 4 d1 + 2 d1 + 12 9 ± 0,8 VR2 V 400385
38 43 36 5,5 9 5 d1 + 2 d1 + 15 7 ± 1 VR1 R 400400

36 5,5 9 5 d1 + 2 d1 + 15 7 ± 1 VR1 V 400404
36 9,5 13 5 d1 + 2 d1 + 15 11 ± 1 VR2 R 400401
36 9,5 13 5 d1 + 2 d1 + 15 11 ± 1 VR2 V 400405
43 48 40 5,5 9 5 d1 + 2 d1 + 15 7 ± 1 VR1 R 400450

40 5,5 9 5 d1 + 2 d1 + 15 7 ± 1 VR1 V 400454
40 9,5 13 5 d1 + 2 d1 + 15 11 ± 1 VR2 R 400451
40 9,5 13 5 d1 + 2 d1 + 15 11 ± 1 VR2 V 400455
48 53 45 5,5 9 5 d1 + 2 d1 + 15 7 ± 1 VR1 R 400500

45 5,5 9 5 d1 + 2 d1 + 15 7 ± 1 VR1 V 400504
45 9,5 13 5 d1 + 2 d1 + 15 11 ± 1 VR2 R 400501
45 9,5 13 5 d1 + 2 d1 + 15 11 ± 1 VR2 V 400505

d1 53 – 195 mm
B1
d D1 d1 D
b1

d1 d b1 b c D1 D B1
over incl. max min
mm – – –
53 58 49 5,5 9 5 d1 + 2 d1 + 15 7 ± 1 VR1 R 400550

49 5,5 9 5 d1 + 2 d1 + 15 7 ± 1 VR1 V 400554
49 9,5 13 5 d1 + 2 d1 + 15 11 ± 1 VR2 R 400551
49 9,5 13 5 d1 + 2 d1 + 15 11 ± 1 VR2 V 400555
58 63 54 5,5 9 5 d1 + 2 d1 + 15 7 ± 1 VR1 R 400600

54 5,5 9 5 d1 + 2 d1 + 15 7 ± 1 VR1 V 400604
54 9,5 13 5 d1 + 2 d1 + 15 11 ± 1 VR2 R 400601
54 9,5 13 5 d1 + 2 d1 + 15 11 ± 1 VR2 V 400605
63 68 58 5,5 9 5 d1 + 2 d1 + 15 7 ± 1 VR1 R 400650

58 5,5 9 5 d1 + 2 d1 + 15 7 ± 1 VR1 V 400654
58 9,5 13 5 d1 + 2 d1 + 15 11 ± 1 VR2 R 400651
58 9,5 13 5 d1 + 2 d1 + 15 11 ± 1 VR2 V 400655
68 73 63 6,8 11 6 d1 + 3 d1 + 18 9 ± 1,2 VR1 R 400700

63 6,8 11 6 d1 + 3 d1 + 18 9 ± 1,2 VR1 V 400704
63 11,3 15,5 6 d1 + 3 d1 + 18 13,5 ± 1,2 VR2 R 400701
63 11,3 15,5 6 d1 + 3 d1 + 18 13,5 ± 1,2 VR2 V 400705
73 78 67 6,8 11 6 d1 + 3 d1 + 18 9 ± 1,2 VR1 R 400750

67 6,8 11 6 d1 + 3 d1 + 18 13,5 ± 1,2 VR2 R 400751
67 11,3 15,5 6 d1 + 3 d1 + 18 13,5 ± 1,2 VR2 V 400755
78 83 72 6,8 11 6 d1 + 3 d1 + 18 9 ± 1,2 VR1 R 400800

72 6,8 11 6 d1 + 3 d1 + 18 9 ± 1,2 VR1 V 400804
72 11,3 15,5 6 d1 + 3 d1 + 18 13,5 ± 1,2 VR2 R 400801
72 11,3 15,5 6 d1 + 3 d1 + 18 13,5 ± 1,2 VR2 V 400805
83 88 76 6,8 11 6 d1 + 3 d1 + 18 9 ± 1,2 VR1 R 400850

76 6,8 11 6 d1 + 3 d1 + 18 9 ± 1,2 VR1 V 400854
76 11,3 15,5 6 d1 + 3 d1 + 18 13,5 ± 1,2 VR2 R 400851
76 11,3 15,5 6 d1 + 3 d1 + 18 13,5 ± 1,2 VR2 V 400855
88 93 81 6,8 11 6 d1 + 3 d1 + 18 9 ± 1,2 VR1 R 400900

81 6,8 11 6 d1 + 3 d1 + 18 9 ± 1,2 VR1 V 400904
81 11,3 15,5 6 d1 + 3 d1 + 18 13,5 ± 1,2 VR2 R 400901
81 11,3 15,5 6 d1 + 3 d1 + 18 13,5 ± 1,2 VR2 V 400905
93 98 85 6,8 11 6 d1 + 3 d1 + 18 9 ± 1,2 VR1 R 400950

85 6,8 11 6 d1 + 3 d1 + 18 9 ± 1,2 VR1 V 400954
85 11,3 15,5 6 d1 + 3 d1 + 18 13,5 ± 1,2 VR2 R 400951
85 11,3 15,5 6 d1 + 3 d1 + 18 13,5 ± 1,2 VR2 V 400955

d1 d b1 b c D1 D B1
over incl. max min
mm – – –
98 105 90 6,8 11 6 d1 + 3 d1 + 18 9 ± 1,2 VR1 R 401000

90 6,8 11 6 d1 + 3 d1 + 18 9 ± 1,2 VR1 V 401004
90 11,3 15,5 6 d1 + 3 d1 + 18 13,5 ± 1,2 VR2 R 401001
90 11,3 15,5 6 d1 + 3 d1 + 18 13,5 ± 1,2 VR2 V 401005
105 115 99 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 R 401102

99 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 V 401106
99 7,9 12,8 7 d1 + 4 d1 + 21 10,5 ± 1,5 VR1 R 401100
99 7,9 12,8 7 d1 + 4 d1 + 21 10,5 ± 1,5 VR1 V 401104
99 13,1 18 7 d1 + 4 d1 + 21 15,5 ± 1,5 VR2 R 401101
99 13,1 18 7 d1 + 4 d1 + 21 15,5 ± 1,5 VR2 V 401105
115 125 108 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 R 401202
108 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 V 401206
108 7,9 12,8 7 d1 + 4 d1 + 21 10,5 ± 1,5 VR1 R 401200
108 7,9 12,8 7 d1 + 4 d1 + 21 10,5 ± 1,5 VR1 V 401204
108 13,1 18 7 d1 + 4 d1 + 21 15,5 ± 1,5 VR2 R 401201
108 13,1 18 7 d1 + 4 d1 + 21 15,5 ± 1,5 VR2 V 401205
125 135 117 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 R 401302
117 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 V 401306
117 7,9 12,8 7 d1 + 4 d1 + 21 10,5 ± 1,5 VR1 R 401300
117 7,9 12,8 7 d1 + 4 d1 + 21 10,5 ± 1,5 VR1 V 401304
117 13,1 18 7 d1 + 4 d1 + 21 15,5 ± 1,5 VR2 R 401301
117 13,1 18 7 d1 + 4 d1 + 21 15,5 ± 1,5 VR2 V 401305
135 145 126 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 R 401402
126 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 V 401406
126 7,9 12,8 7 d1 + 4 d1 + 21 10,5 ± 1,5 VR1 R 401400
126 7,9 12,8 7 d1 + 4 d1 + 21 10,5 ± 1,5 VR1 V 401404
126 13,1 18 7 d1 + 4 d1 + 21 15,5 ± 1,5 VR2 R 401401
126 13,1 18 7 d1 + 4 d1 + 21 15,5 ± 1,5 VR2 V 401405
145 155 135 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 R 401502
135 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 V 401506
135 7,9 12,8 7 d1 + 4 d1 + 21 10,5 ± 1,5 VR1 R 401500
135 7,9 12,8 7 d1 + 4 d1 + 21 10,5 ± 1,5 VR1 V 401504
135 13,1 18 7 d1 + 4 d1 + 21 15,5 ± 1,5 VR2 R 401501
135 13,1 18 7 d1 + 4 d1 + 21 15,5 ± 1,5 VR2 V 401505
144 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 R 401602

155 165 144 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 V 401606
144 9 14,5 8 d1 + 4 d1 + 24 12 ± 1,8 VR1 R 401600
144 9 14,5 8 d1 + 4 d1 + 24 12 ± 1,8 VR1 V 401604
144 15 20,5 8 d1 + 4 d1 + 24 18 ± 1,8 VR2 R 401601
144 15 20,5 8 d1 + 4 d1 + 24 18 ± 1,8 VR2 V 401605
165 175 153 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 R 401702 7.2
153 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 V 401706
153 9 14,5 8 d1 + 4 d1 + 24 12 ± 1,8 VR1 R 401700
153 9 14,5 8 d1 + 4 d1 + 24 12 ± 1,8 VR1 V 401704
153 15 20,5 8 d1 + 4 d1 + 24 18 ± 1,8 VR2 R 401701
153 15 20,5 8 d1 + 4 d1 + 24 18 ± 1,8 VR2 V 401705
175 185 162 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 R 401802
162 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 V 401806
162 9 14,5 8 d1 + 4 d1 + 24 12 ± 1,8 VR1 R 401800
162 9 14,5 8 d1 + 4 d1 + 24 12 ± 1,8 VR1 V 401804
162 15 20,5 8 d1 + 4 d1 + 24 18 ± 1,8 VR2 R 401801
162 15 20,5 8 d1 + 4 d1 + 24 18 ± 1,8 VR2 V 401805
185 195 171 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 R 401902
171 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 V 401906
171 9 14,5 8 d1 + 4 d1 + 24 12 ± 1,8 VR1 R 401900
171 9 14,5 8 d1 + 4 d1 + 24 12 ± 1,8 VR1 V 401904
171 15 20,5 8 d1 + 4 d1 + 24 18 ± 1,8 VR2 R 401901
171 15 20,5 8 d1 + 4 d1 + 24 18 ± 1,8 VR2 V 401905

d1 190 – 395 mm
B1
d D1 d1 D
b1

d1 d b1 b c D1 D B1
over incl. max min
mm – – –
195 210 182 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 R 402002
182 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 V 402006
180 9 14,5 8 d1 + 4 d1 + 24 12 ± 1,8 VR1 R 401990
180 9 14,5 8 d1 + 4 d1 + 24 12 ± 1,8 VR1 V 401994
180 15 20,5 8 d1 + 4 d1 + 24 18 ± 1,8 VR2 R 401991
180 15 20,5 8 d1 + 4 d1 + 24 18 ± 1,8 VR2 V 401995
190 210 180 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 R 402000

180 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 V 402004
210 233 198 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 R 402202
198 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 V 402206
198 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 R 402200
198 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 V 402204
233 260 225 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 R 402502
225 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 V 402506
235 265 225 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 R 402500

225 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 V 402504
260 285 247 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 R 402752
247 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 V 402756
265 290 247 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 R 402750

247 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 V 402754
285 310 270 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 R 403002
270 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 V 403006
290 310 270 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 R 403000

270 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 V 403004
300 305 294 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 403003

294 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470301
305 310 299 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 403053

299 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470306
310 335 292 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 R 403252
292 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 V 403256

d1 d b1 b c D1 D B1
over incl. max min
mm – – –
310 335 292 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 R 403250

cont. 292 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 V 403254
310 315 304 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 403103

304 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470311
315 320 309 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 403153

309 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470316
320 325 314 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 403203

314 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470321
325 330 319 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 403253

319 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470326
330 335 323 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 403303

323 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470331
335 365 315 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 R 403502
315 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 V 403506
315 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 R 403500
315 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 V 403504
335 340 328 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 403353

328 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470336
340 345 333 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 403403

328 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470341
345 350 338 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 403453

338 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470346
350 355 343 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 403503

343 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470351
355 360 347 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 403553

347 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470356
360 365 352 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 403603

357 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470361
365 385 337 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 R 403752
337 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 V 403756
365 390 337 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 R 403750

337 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 V 403754
357 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 403653
7.2
370 375 362 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 403703
362 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470371
375 380 367 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 403753

367 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470376
380 385 371 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 403803

371 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470381
385 410 360 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 R 404002
360 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 V 404006
390 430 360 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 R 404000

360 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 V 404004
385 390 376 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 403853

376 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470386
390 395 381 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 403903

381 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470391

d1 395 – 540 mm
B1
d D1 d1 D
b1

d1 d b1 b c D1 D B1
over incl. max min
mm – – –
395 400 386 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 403953

386 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470396
400 405 391 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 404003

391 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470401
405 410 396 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 404053

396 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470406
410 415 401 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 404103

401 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470411
415 420 405 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 404153

405 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470416
420 425 410 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 404203

410 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470421
425 430 415 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 404253

415 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470426
410 440 382 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 R 404252
382 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 V 404256
440 475 405 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 R 404502
405 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 V 404506
430 480 405 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 R 404500

405 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 V 404504
430 435 420 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 404303

420 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470431
435 440 425 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 404353

425 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470436
440 445 429 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 404403

429 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470441
445 450 434 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 404453

434 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470446

d1 d b1 b c D1 D B1
over incl. max min
mm – – –
450 455 439 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 404503

439 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470451
455 460 444 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 404553

444 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470456
460 465 448 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 404603

448 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470461
465 470 453 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 404653

453 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470466
470 475 458 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 404703

458 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470471
475 480 463 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 404753

463 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470476
475 510 450 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 R 405002
450 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 V 405006
510 540 472 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 R 405252
472 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 V 405256
480 530 450 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 R 405000

450 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 V 405004
480 485 468 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 404803

468 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470481
485 490 473 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 404853

473 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470486
490 495 478 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 404903

478 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470491
495 500 483 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 404953

483 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470496
500 505 488 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 405003

488 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470501
505 510 493 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 405053

493 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470506
510 515 497 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 405103

497 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470511
7.2
515 520 502 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 405153
502 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470516
520 525 507 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 405203

507 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470521
525 530 512 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 405253

512 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470526
540 575 495 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 R 405502
495 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 V 405506
530 580 495 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 R 405500

495 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 V 405504
530 535 517 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 405303

517 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470531
535 540 521 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 405353

521 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470536

d1 540 – 758 mm
B1
d D1 d1 D
b1

d1 d b1 b c D1 D B1
over incl. max min
mm – – –
540 545 526 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 405403

526 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470541
545 550 531 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 405453

531 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470546
550 555 536 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 405503

536 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470551
555 560 541 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 405553

541 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470556
560 565 546 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 405603

546 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470561
565 570 550 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 405653

550 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470566
570 575 555 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 405703

555 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470571
575 580 560 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 405753

560 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470576
575 625 540 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 R 406002
540 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 V 406006
580 630 540 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 R 406000

540 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 V 406004
580 585 565 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 405803

565 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470581
585 590 570 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 405853

570 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470586
590 600 575 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 405903

575 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470591
600 610 582 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 406003

582 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470601

d1 d b1 b c D1 D B1
over incl. max min
mm – – –
610 620 592 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 406103

592 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470611
620 630 602 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 406203

602 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470621
615 675 600 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 R 406502
600 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 V 406506
630 665 600 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 R 406500

600 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 V 406504
630 640 612 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 406303

612 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470631
640 650 621 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 406403

621 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470641
650 660 631 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 406503

631 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470651
660 670 640 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 406603

640 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470661
675 710 630 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 R 407002
630 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 V 407006
665 705 630 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 R 407000

630 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 V 407004
670 680 650 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 406703

650 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470671
680 690 660 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 406803

660 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470681
690 700 670 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 406903

670 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470691
700 710 680 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 407003

680 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470701
710 740 670 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 R 407252
670 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 V 407256
705 745 670 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 R 407250

670 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 V 407254
7.2
710 720 689 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 407103
689 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470711
720 730 699 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 407203

699 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470721
730 740 709 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 407303

709 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470731
740 750 718 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 407403

718 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470741
740 775 705 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 R 407502
705 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 V 407506
745 785 705 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 R 407500

705 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 V 407504
750 758 728 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 407503

728 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470751

d1 758 – 1 045 mm
B1
d D1 d1 D
b1

d1 d b1 b c D1 D B1
over incl. max min
mm – – –
758 766 735 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 407603

735 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470761
766 774 743 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 407703

743 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470771
774 783 751 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 407803

751 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470781
783 792 759 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 407903

759 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470791
775 825 745 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 R 408002
745 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 V 408006
785 830 745 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 R 408000

745 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 V 408004
792 801 768 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 408003

768 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470801
801 810 777 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 408103

777 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470811
810 821 786 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 408203

786 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470821
821 831 796 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 408303

796 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470831
825 875 785 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 R 408502
785 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 V 408506
830 875 785 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 R 408500

785 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 V 408504
831 841 805 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 408403

805 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470841
841 851 814 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 408503

814 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470851

d1 d b1 b c D1 D B1
over incl. max min
mm – – –
851 861 824 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 408603

824 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470861
861 871 833 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 408703
833 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470871
871 882 843 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 408803

843 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470881
875 925 825 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 R 409002
825 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 V 409006
875 920 825 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 R 409000

825 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 V 409004
882 892 853 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 408903

853 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470891
892 912 871 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 409003

871 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470901
912 922 880 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 409203

880 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470921
925 975 865 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 R 409502
865 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 V 409506
920 965 865 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 R 409500

865 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 V 409504
922 933 890 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 409303

890 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470931
933 944 900 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 409403

900 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470941
944 955 911 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 409503

911 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470951
955 966 921 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 409603

921 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470961
975 1025 910 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 R 410002
910 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 V 410006
965 1015 910 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 R 410000

910 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 V 410004
966 977 932 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 409703 7.2

932 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470971
977 988 942 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 409803

942 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470981
988 999 953 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 409903

953 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 470991
999 1 010 963 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 410003

963 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 471001
1 010 1 025 973 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 410203

973 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 471021
1 025 1 075 955 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 R 410502
955 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 V 410506
1 015 1 065 955 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 R 410500
1 025 1 045 990 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 410403

990 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 471041

d1 1 045 – 1 540 mm
B1
d D1 d1 D
b1

d1 d b1 b c D1 D B1
over incl. max min
mm – – –
1 045 1 065 1 008 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 410603

1 008 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 471061
1 075 1 125 1 000 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 R 411002
1 000 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 V 411006
1 065 1 115 1 000 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 R 411000

1 027 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 410803
1 027 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 471081
1 085 1 105 1 045 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 411003

1 045 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 471101
1 105 1 125 1 065 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 411203

1 065 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 471121
1 125 1 175 1 045 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 R 411502
1 045 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 V 411506
1 115 1 165 1 045 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 R 411500
1 125 1 145 1 084 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 411403

1 084 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 471141
1 145 1 165 1 103 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 411603

1 103 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 471161
1 175 1 225 1 090 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 R 412002
1 090 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 V 412006
1 165 1 215 1 090 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 R 412000
1 165 1 185 1 121 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 411803

1 121 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 471181
1 185 1 205 1 139 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 412003

1 139 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 471201
1 205 1 225 1 157 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 412203

1 157 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 471221

d1 d b1 b c D1 D B1
over incl. max min
mm – – –
1 225 1 275 1 135 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 R 412502
1 135 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 V 412506
1 215 1 270 1 135 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 R 412500
1 225 1 245 1 176 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 412403

1 176 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 471241
1 245 1 270 1 195 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 412603

1 195 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 471261
1 270 1295 1 218 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 412803

1 218 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 471281
1 275 1 325 1 180 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 R 413002
1 180 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 V 413006
1 270 1 320 1 180 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 R 413000
1 295 1 315 1 240 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 413003

1 240 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 471301
1 315 1 340 1 259 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 413253

1 259 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 471326
1 325 1 375 1 225 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 R 413502
1 225 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 V 413506
1 320 1 370 1 225 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 R 413500
1 340 1 365 1 281 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 413503

1 281 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 471351
1 365 1 390 1 305 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 413753

1 305 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 471376
1 375 1 425 1 270 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 R 414002
1 270 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 V 414006
1 370 1 420 1 270 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 R 414000
1 390 1 415 1 328 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 414003

1 328 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 471401
1 415 1 440 1 350 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 414253

1 350 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 471426
1 425 1 475 1 315 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 R 414502 7.2
1 315 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 V 414506
1 420 1 470 1 315 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 R 414500
1 440 1 465 1 374 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 414503

1 374 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 471451
1 465 1 490 1 397 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 414753

1 397 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 471476
1 475 1 525 1 360 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 R 415002
1 360 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 V 415006
1 470 1 520 1 360 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 R 415000
1 490 1 515 1 419 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 415003

1 419 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 471501
1 515 1 540 1 443 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 415253

1 443 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 471526

d1 1 525 – 2 020 mm
B1
d D1 d1 D
b1

d1 d b1 b c D1 D B1
over incl. max min
mm – – –
1 525 1 575 1 405 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 R 415502
1 405 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 V 415506
1 520 1 570 1 405 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 R 415500
1 540 1 570 1 467 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 415503

1 467 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 471551
1 570 1 600 1 495 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 415753

1 495 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 471576
1 575 1 625 1 450 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 R 416002
1 450 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 V 416006
1 570 1 620 1 450 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 R 416000
1 600 1 640 1 524 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 416003

1 524 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 471601
1 625 1 675 1 495 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 R 416502
1 495 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 V 416506
1 620 1 670 1 495 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 R 416500
1 640 1 680 1 559 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 416503

1 559 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 471651
1 675 1 725 1 540 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 R 417002
1 540 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 V 417006
1 670 1 720 1 540 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 R 417000
1 680 1 720 1 596 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 417003

1 596 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 471701
1 725 1 775 1 585 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 R 417502
1 585 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 V 417506
1 720 1 770 1 585 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 R 417500
1 720 1 765 1 632 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 417503

1 632 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 471751

d1 d b1 b c D1 D B1
over incl. max min
mm – – –
1 765 1 810 1 671 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 418003

1 671 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 471801
1 775 1 825 1 630 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 R 418002
1 630 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 V 418006
1 770 1 820 1 630 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 R 418000
1 810 1 855 1 714 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 418503

1 714 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 471851
1 825 1 875 1 675 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 R 418502
1 675 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 V 418506
1 820 1 870 1 675 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 R 418500
1 855 1 905 1 753 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 419003

1 753 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 471901
1 875 1 925 1 720 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 R 419002
1 720 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 V 419006
1 870 1 920 1 720 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 R 419000
1 905 1 955 1 794 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 419503

1 794 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 471951
1 925 1 975 1 765 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 R 419502
1 765 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 V 419506
1 920 1 970 1 765 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 R 419500
1 955 2 010 1 844 32,5 65 30 d1 + 24 d1 + 115 50 ± 12 VR4 R 420003

1 844 32,5 65 21 d1 + 24 d1 + 115 50 ± 12 VR6 R 472001
1 975 2 025 1 810 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 R 420002
1 810 6 10,5 6,5 d1 + 5 d1 + 20 8 ± 1,5 VR3 V 420006
1 970 2 020 1 810 14,3 25 15 d1 + 10 d1 + 45 20 ± 4 VR1 R 420000
7.2
V-ring seals – inch dimensions, for North American market

d1 0.11 – 2.09 in.
B1
d D1 d1 D
b1
Dimensions Design Lip Desig

Shaft diameter Seal inside dia Nominal Seal Nominal Clear- Counter Seal fitted code nation
range meter, free state seal height seat width seal width ance face width
d1 d c b1 b D1 (=d1+) D (=d1 +) B1
over incl. max min
in. in. – – –
0.11 0.14 0.10 0.06 0.08 0.12 0.04 0.16 0.10 ± 0.012 VR1 R 400030
0.10 0.06 0.08 0.12 0.04 0.16 0.10 ± 0.012 VR1 V 400034
0.14 0.18 0.13 0.08 0.09 0.15 0.04 0.24 0.12 ± 0.016 VR1 R 400040
0.13 0.08 0.09 0.15 0.04 0.24 0.12 ± 0.016 VR1 V 400044
0.18 0.22 0.16 0.08 0.09 0.15 0.04 0.24 0.12 ± 0.016 VR1 R 400050
0.16 0.08 0.09 0.15 0.04 0.24 0.12 ± 0.016 VR1 V 400054
0.16 0.08 0.15 0.20 0.04 0.24 0.18 ± 0.016 VR2 R 400051
0.16 0.08 0.15 0.20 0.04 0.24 0.18 ± 0.016 VR2 V 400055
0.22 0.26 0.20 0.08 0.09 0.15 0.04 0.24 0.12 ± 0.016 VR1 R 400060
0.20 0.08 0.09 0.15 0.04 0.24 0.12 ± 0.016 VR1 V 400064
0.20 0.08 0.15 0.20 0.04 0.24 0.18 ± 0.016 VR2 R 400061
0.20 0.08 0.15 0.20 0.04 0.24 0.18 ± 0.016 VR2 V 400065
0.26 0.31 0.24 0.08 0.09 0.15 0.04 0.24 0.12 ± 0.016 VR1 R 400070
0.24 0.08 0.09 0.15 0.04 0.24 0.12 ± 0.016 VR1 V 400074
0.24 0.08 0.15 0.20 0.04 0.24 0.18 ± 0.016 VR2 R 400071
0.24 0.08 0.15 0.20 0.04 0.24 0.18 ± 0.016 VR2 V 400075
0.31 0.37 0.28 0.08 0.09 0.15 0.04 0.24 0.12 ± 0.016 VR1 R 400080
0.28 0.08 0.09 0.15 0.04 0.24 0.12 ± 0.016 VR1 V 400084
0.28 0.08 0.15 0.20 0.04 0.24 0.18 ± 0.016 VR2 R 400081
0.28 0.08 0.15 0.20 0.04 0.24 0.18 ± 0.016 VR2 V 400085
0.37 0.45 0.35 0.12 0.13 0.22 0.04 0.35 0.18 ± 0.02 VR1 R 400100
0.35 0.12 0.13 0.22 0.04 0.35 0.18 ± 0.02 VR1 V 400104
0.35 0.12 0.22 0.30 0.04 0.35 0.26 ± 0.02 VR2 R 400101
0.35 0.12 0.22 0.30 0.04 0.35 0.26 ± 0.02 VR2 V 400105
0.45 0.49 0.41 0.12 0.13 0.22 0.04 0.35 0.18 ± 0.02 VR1 R 400120
0.41 0.12 0.13 0.22 0.04 0.35 0.18 ± 0.02 VR1 V 400124
0.41 0.12 0.22 0.30 0.04 0.35 0.26 ± 0.02 VR2 R 400121
0.41 0.12 0.22 0.30 0.04 0.35 0.26 ± 0.02 VR2 V 400125
0.49 0.53 0.46 0.12 0.13 0.22 0.04 0.35 0.18 ± 0.02 VR1 R 400130
0.46 0.12 0.13 0.22 0.04 0.35 0.18 ± 0.02 VR1 V 400134
0.53 0.61 0.49 0.12 0.13 0.22 0.04 0.35 0.18 ± 0.02 VR1 R 400140
0.49 0.12 0.13 0.22 0.04 0.35 0.18 ± 0.02 VR1 V 400144

d1 d c b1 b D1 (=d1+) D (=d1 +) B1
over incl. max min
in. in. – – –
0.53 0.61 0.49 0.12 0.22 0.30 0.04 0.35 0.26 ± 0.02 VR2 R 400141

cont. 0.49 0.12 0.22 0.30 0.04 0.35 0.26 ± 0.02 VR2 V 400145
0.61 0.67 0.55 0.12 0.13 0.22 0.04 0.35 0.18 ± 0.02 VR1 R 400160
0.55 0.12 0.13 0.22 0.04 0.35 0.18 ± 0.02 VR1 V 400164
0.61 0.69 0.55 0.12 0.22 0.30 0.04 0.35 0.26 ± 0.02 VR2 R 400161
0.55 0.12 0.22 0.30 0.04 0.35 0.26 ± 0.02 VR2 V 400165
0.69 0.75 0.63 0.12 0.13 0.22 0.04 0.35 0.18 ± 0.02 VR1 R 400180
0.63 0.12 0.13 0.22 0.04 0.35 0.18 ± 0.02 VR1 V 400184
0.63 0.12 0.22 0.30 0.04 0.35 0.26 ± 0.02 VR2 R 400181
0.63 0.12 0.22 0.30 0.04 0.35 0.26 ± 0.02 VR2 V 400185
0.75 0.83 0.71 0.16 0.19 0.30 0.08 0.47 0.24 ± 0.03 VR1 R 400200
0.71 0.16 0.19 0.30 0.08 0.47 0.24 ± 0.03 VR1 V 400204
0.71 0.16 0.31 0.41 0.08 0.47 0.35 ± 0.03 VR2 R 400201
0.71 0.16 0.31 0.41 0.08 0.47 0.35 ± 0.03 VR2 V 400205
0.83 0.94 0.79 0.16 0.19 0.30 0.08 0.47 0.24 ± 0.03 VR1 R 400220
0.79 0.16 0.19 0.30 0.08 0.47 0.24 ± 0.03 VR1 V 400224
0.79 0.16 0.31 0.41 0.08 0.47 0.35 ± 0.03 VR2 R 400221
0.79 0.16 0.31 0.41 0.08 0.47 0.35 ± 0.03 VR2 V 400225
0.94 1.06 0.87 0.16 0.19 0.30 0.08 0.47 0.24 ± 0.03 VR1 R 400250
0.87 0.16 0.19 0.30 0.08 0.47 0.24 ± 0.03 VR1 V 400254
0.87 0.16 0.31 0.41 0.08 0.47 0.35 ± 0.03 VR2 R 400251
0.87 0.16 0.31 0.41 0.08 0.47 0.35 ± 0.03 VR2 V 400255
1.06 1.14 0.98 0.16 0.19 0.30 0.08 0.47 0.24 ± 0.03 VR1 R 400280
0.98 0.16 0.19 0.30 0.08 0.47 0.24 ± 0.03 VR1 V 400284
0.98 0.16 0.31 0.41 0.08 0.47 0.35 ± 0.03 VR2 R 400281
0.98 0.16 0.31 0.41 0.08 0.47 0.35 ± 0.03 VR2 V 400285
1.14 1.22 1.06 0.16 0.19 0.30 0.08 0.47 0.24 ± 0.03 VR1 R 400300
1.06 0.16 0.19 0.30 0.08 0.47 0.24 ± 0.03 VR1 V 400304
1.06 0.16 0.31 0.41 0.08 0.47 0.35 ± 0.03 VR2 R 400301
1.06 0.16 0.31 0.41 0.08 0.47 0.35 ± 0.03 VR2 V 400305
1.22 1.30 1.14 0.16 0.19 0.30 0.08 0.47 0.24 ± 0.03 VR1 R 400320
1.14 0.16 0.19 0.30 0.08 0.47 0.24 ± 0.03 VR1 V 400324
1.14 0.16 0.31 0.41 0.08 0.47 0.35 ± 0.03 VR2 R 400321
1.14 0.16 0.31 0.41 0.08 0.47 0.35 ± 0.03 VR2 V 400325
1.30 1.42 1.22 0.16 0.19 0.30 0.08 0.47 0.24 ± 0.03 VR1 R 400350
1.22 0.16 0.19 0.30 0.08 0.47 0.24 ± 0.03 VR1 V 400354
1.22 0.16 0.31 0.41 0.08 0.47 0.35 ± 0.03 VR2 R 400351
1.22 0.16 0.31 0.41 0.08 0.47 0.35 ± 0.03 VR2 V 400355 7.2
1.42 1.50 1.34 0.16 0.19 0.30 0.08 0.47 0.24 ± 0.03 VR1 R 400380
1.34 0.16 0.19 0.30 0.08 0.47 0.24 ± 0.03 VR1 V 400384
1.34 0.16 0.31 0.41 0.08 0.47 0.35 ± 0.03 VR2 R 400381
1.34 0.16 0.31 0.41 0.08 0.47 0.35 ± 0.03 VR2 V 400385
1.50 1.69 1.42 0.20 0.22 0.35 0.08 0.59 0.28 ± 0.04 VR1 R 400400
1.42 0.20 0.22 0.35 0.08 0.59 0.28 ± 0.04 VR1 V 400404
1.42 0.20 0.37 0.51 0.08 0.59 0.43 ± 0.04 VR2 R 400401
1.42 0.20 0.37 0.51 0.08 0.59 0.43 ± 0.04 VR2 V 400405
1.69 1.89 1.57 0.20 0.22 0.35 0.08 0.59 0.28 ± 0.04 VR1 R 400450
1.57 0.20 0.22 0.35 0.08 0.59 0.28 ± 0.04 VR1 V 400454
1.57 0.20 0.37 0.51 0.08 0.59 0.43 ± 0.04 VR2 R 400451
1.57 0.20 0.37 0.51 0.08 0.59 0.43 ± 0.04 VR2 V 400455
1.89 2.09 1.77 0.20 0.22 0.35 0.08 0.59 0.28 ± 0.04 VR1 R 400500
1.77 0.20 0.22 0.35 0.08 0.59 0.28 ± 0.04 VR1 V 400504
1.77 0.20 0.37 0.51 0.08 0.59 0.43 ± 0.04 VR2 R 400501
1.77 0.20 0.37 0.51 0.08 0.59 0.43 ± 0.04 VR2 V 400505

d1 2.09 – 7.68 in.
B1
d D1 d1 D
b1

d1 d c b1 b D1 (= d1+) D (= d1 +) B1
over incl. max min
in. in. – – –
2.09 2.28 1.93 0.20 0.22 0.35 0.08 0.59 0.28 ± 0.04 VR1 R 400550
1.93 0.20 0.22 0.35 0.08 0.59 0.28 ± 0.04 VR1 V 400554
1.93 0.20 0.37 0.51 0.08 0.59 0.43 ± 0.04 VR2 R 400551
1.93 0.20 0.37 0.51 0.08 0.59 0.43 ± 0.04 VR2 V 400555
2.28 2.48 2.13 0.20 0.22 0.35 0.08 0.59 0.28 ± 0.04 VR1 R 400600
2.13 0.20 0.22 0.35 0.08 0.59 0.28 ± 0.04 VR1 V 400604
2.13 0.20 0.37 0.51 0.08 0.59 0.43 ± 0.04 VR2 R 400601
2.13 0.20 0.37 0.51 0.08 0.59 0.43 ± 0.04 VR2 V 400605
2.48 2.68 2.28 0.20 0.22 0.35 0.08 0.59 0.28 ± 0.04 VR1 R 400650
2.28 0.20 0.22 0.35 0.08 0.59 0.28 ± 0.04 VR1 V 400654
2.28 0.20 0.37 0.51 0.08 0.59 0.43 ± 0.04 VR2 R 400651
2.28 0.20 0.37 0.51 0.08 0.59 0.43 ± 0.04 VR2 V 400655
2.68 2.87 2.48 0.24 0.27 0.43 0.12 0.71 0.35 ± 0.05 VR1 R 400700
2.48 0.24 0.27 0.43 0.12 0.71 0.35 ± 0.05 VR1 V 400704
2.48 0.24 0.44 0.61 0.12 0.71 0.53 ± 0.05 VR2 R 400701
2.48 0.24 0.44 0.61 0.12 0.71 0.53 ± 0.05 VR2 V 400705
2.87 3.07 2.64 0.24 0.27 0.43 0.12 0.71 0.35 ± 0.05 VR1 R 400750
2.64 0.24 0.27 0.43 0.12 0.71 0.53 ± 0.05 VR2 R 400751
2.64 0.24 0.44 0.61 0.12 0.71 0.53 ± 0.05 VR2 V 400755
3.07 3.27 2.83 0.24 0.27 0.43 0.12 0.71 0.35 ± 0.05 VR1 R 400800
2.83 0.24 0.27 0.43 0.12 0.71 0.35 ± 0.05 VR1 V 400804
2.83 0.24 0.44 0.61 0.12 0.71 0.53 ± 0.05 VR2 R 400801
2.83 0.24 0.44 0.61 0.12 0.71 0.53 ± 0.05 VR2 V 400805
3.27 3.46 2.99 0.24 0.27 0.43 0.12 0.71 0.35 ± 0.05 VR1 R 400850
2.99 0.24 0.27 0.43 0.12 0.71 0.35 ± 0.05 VR1 V 400854
2.99 0.24 0.44 0.61 0.12 0.71 0.53 ± 0.05 VR2 R 400851
2.99 0.24 0.44 0.61 0.12 0.71 0.53 ± 0.05 VR2 V 400855
3.46 3.66 3.19 0.24 0.27 0.43 0.12 0.71 0.35 ± 0.05 VR1 R 400900
3.19 0.24 0.27 0.43 0.12 0.71 0.35 ± 0.05 VR1 V 400904
3.19 0.24 0.44 0.61 0.12 0.71 0.53 ± 0.05 VR2 R 400901
3.19 0.24 0.44 0.61 0.12 0.71 0.53 ± 0.05 VR2 V 400905
3.66 3.86 3.35 0.24 0.27 0.43 0.12 0.71 0.35 ± 0.05 VR1 R 400950
3.35 0.24 0.27 0.43 0.12 0.71 0.35 ± 0.05 VR1 V 400954
3.35 0.24 0.44 0.61 0.12 0.71 0.53 ± 0.05 VR2 R 400951
3.35 0.24 0.44 0.61 0.12 0.71 0.53 ± 0.05 VR2 V 400955

d1 d c b1 b D1 (= d1+) D (= d1 +) B1
over incl. max min
in. in. – – –
3.86 4.13 3.54 0.24 0.27 0.43 0.12 0.71 0.35 ± 0.05 VR1 R 401000
3.54 0.24 0.27 0.43 0.12 0.71 0.35 ± 0.05 VR1 V 401004
3.54 0.24 0.44 0.61 0.12 0.71 0.53 ± 0.05 VR2 R 401001
3.54 0.24 0.44 0.61 0.12 0.71 0.53 ± 0.05 VR2 V 401005
4.13 4.53 3.90 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 R 401102
3.90 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 V 401106
3.90 0.28 0.31 0.50 0.16 0.83 0.41 ± 0.06 VR1 R 401100
3.90 0.28 0.31 0.50 0.16 0.83 0.41 ± 0.06 VR1 V 401104
3.90 0.28 0.52 0.71 0.16 0.83 0.61 ± 0.06 VR2 R 401101
3.90 0.28 0.52 0.71 0.16 0.83 0.61 ± 0.06 VR2 V 401105
4.53 4.92 4.25 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 R 401202
4.25 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 V 401206
4.25 0.28 0.31 0.50 0.16 0.83 0.41 ± 0.06 VR1 R 401200
4.25 0.28 0.31 0.50 0.16 0.83 0.41 ± 0.06 VR1 V 401204
4.25 0.28 0.52 0.71 0.16 0.83 0.61 ± 0.06 VR2 R 401201
4.25 0.28 0.52 0.71 0.16 0.83 0.61 ± 0.06 VR2 V 401205
4.92 5.31 4.61 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 R 401302
4.61 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 V 401306
4.61 0.28 0.31 0.50 0.16 0.83 0.41 ± 0.06 VR1 R 401300
4.61 0.28 0.31 0.50 0.16 0.83 0.41 ± 0.06 VR1 V 401304
4.61 0.28 0.52 0.71 0.16 0.83 0.61 ± 0.06 VR2 R 401301
4.61 0.28 0.52 0.71 0.16 0.83 0.61 ± 0.06 VR2 V 401305
5.31 5.71 4.96 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 R 401402
4.96 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 V 401406
4.96 0.28 0.31 0.50 0.16 0.83 0.41 ± 0.06 VR1 R 401400
4.96 0.28 0.31 0.50 0.16 0.83 0.41 ± 0.06 VR1 V 401404
4.96 0.28 0.52 0.71 0.16 0.83 0.61 ± 0.06 VR2 R 401401
4.96 0.28 0.52 0.71 0.16 0.83 0.61 ± 0.06 VR2 V 401405
5.71 6.10 5.31 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 R 401502
5.31 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 V 401506
5.31 0.28 0.31 0.50 0.16 0.83 0.41 ± 0.06 VR1 R 401500
5.31 0.28 0.31 0.50 0.16 0.83 0.41 ± 0.06 VR1 V 401504
5.31 0.28 0.52 0.71 0.16 0.83 0.61 ± 0.06 VR2 R 401501
5.31 0.28 0.52 0.71 0.16 0.83 0.61 ± 0.06 VR2 V 401505
6.10 6.50 5.67 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 R 401602
5.67 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 V 401606
5.67 0.31 0.35 0.57 0.16 0.94 0.47 ± 0.07 VR1 R 401600
5.67 0.31 0.35 0.57 0.16 0.94 0.47 ± 0.07 VR1 V 401604
5.67 0.31 0.59 0.81 0.16 0.94 0.71 ± 0.07 VR2 R 401601
5.67 0.31 0.59 0.81 0.16 0.94 0.71 ± 0.07 VR2 V 401605
6.50 6.89 6.02 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 R 401702 7.2
6.02 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 V 401706
6.02 0.31 0.35 0.57 0.16 0.94 0.47 ± 0.07 VR1 R 401700
6.02 0.31 0.35 0.57 0.16 0.94 0.47 ± 0.07 VR1 V 401704
6.02 0.31 0.59 0.81 0.16 0.94 0.71 ± 0.07 VR2 R 401701
6.02 0.31 0.59 0.81 0.16 0.94 0.71 ± 0.07 VR2 V 401705
6.89 7.28 6.38 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 R 401802
6.38 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 V 401806
6.38 0.31 0.35 0.57 0.16 0.94 0.47 ± 0.07 VR1 R 401800
6.38 0.31 0.35 0.57 0.16 0.94 0.47 ± 0.07 VR1 V 401804
6.38 0.31 0.59 0.81 0.16 0.94 0.71 ± 0.07 VR2 R 401801
6.38 0.31 0.59 0.81 0.16 0.94 0.71 ± 0.07 VR2 V 401805
7.28 7.68 6.73 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 R 401902
6.73 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 V 401906
6.73 0.31 0.35 0.57 0.16 0.94 0.47 ± 0.07 VR1 R 401900
6.73 0.31 0.35 0.57 0.16 0.94 0.47 ± 0.07 VR1 V 401904
6.73 0.31 0.59 0.81 0.16 0.94 0.71 ± 0.07 VR2 R 401901
6.73 0.31 0.59 0.81 0.16 0.94 0.71 ± 0.07 VR2 V 401905

d1 7.48 – 15.35 in.
B1
d D1 d1 D
b1

d1 d c b1 b D1 (= d1+) D (= d1 +) B1
over incl. max min
in. in. – – –
7.68 8.27 7.17 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 R 402002
7.17 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 V 402006
7.09 0.31 0.35 0.57 0.16 0.94 0.47 ± 0.07 VR1 R 401990
7.09 0.31 0.35 0.57 0.16 0.94 0.47 ± 0.07 VR1 V 401994
7.09 0.31 0.59 0.81 0.16 0.94 0.71 ± 0.07 VR2 R 401991
7.09 0.31 0.59 0.81 0.16 0.94 0.71 ± 0.07 VR2 V 401995
7.48 8.27 7.09 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 R 402000
7.09 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 V 402004
8.27 9.17 7.80 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 R 402202
7.80 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 V 402206
7.80 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 R 402200
7.80 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 V 402204
9.17 10.24 8.86 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 R 402502
8.86 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 V 402506
9.25 10.43 8.86 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 R 402500
8.86 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 V 402504
10.24 11.22 9.72 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 R 402752
9.72 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 V 402756
10.43 11.42 9.72 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 R 402750
9.72 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 V 402754
11.22 12.20 10.63 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 R 403002
10.63 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 V 403006
11.42 12.20 10.63 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 R 403000
10.63 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 V 403004
11.81 12.01 11.57 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 403003
11.57 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470301
12.01 12.20 11.77 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 403053
11.77 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470306
12.20 13.19 11.50 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 R 403252
11.50 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 V 403256

d1 d c b1 b D1 (= d1+) D (= d1 +) B1
over incl. max min
in. in. – – –
12.20 13.19 11.50 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 R 403250

cont. 11.50 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 V 403254
12.20 12.40 11.97 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 403103
11.97 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470311
12.40 12.60 12.17 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 403153
12.17 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470316
12.60 12.80 12.36 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 403203
12.36 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470321
12.80 12.99 12.56 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 403253
12.56 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470326
12.99 13.19 12.72 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 403303
12.72 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470331
13.19 14.37 12.40 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 R 403502
12.40 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 V 403506
12.40 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 R 403500
12.40 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 V 403504
13.19 13.39 12.91 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 403353
12.91 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470336
13.39 13.58 13.11 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 403403
12.91 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470341
13.58 13.78 13.31 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 403453
13.31 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470346
13.78 13.98 13.50 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 403503
13.50 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470351
13.98 14.17 13.66 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 403553
13.66 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470356
14.17 14.37 13.86 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 403603
14.06 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470361
14.37 15.16 13.27 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 R 403752
13.27 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 V 403756
14.37 15.35 13.27 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 R 403750
13.27 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 V 403754
7.2
14.37 14.57 14.06 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 403653
14.57 14.76 14.25 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 403703
14.25 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470371
14.76 14.96 14.45 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 403753
14.45 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470376
14.96 15.16 14.61 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 403803
14.61 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470381
15.16 16.14 14.17 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 R 404002
14.17 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 V 404006
15.35 16.93 14.17 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 R 404000
14.17 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 V 404004
15.16 15.35 14.80 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 403853
14.80 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470386

d1 15.35 – 22.64 in.
B1
d D1 d1 D
b1

d1 d c b1 b D1 (= d1+) D (= d1 +) B1
over incl. max min
in. in. – – –
15.35 15.55 15.00 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 403903
15.00 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470391
15.55 15.75 15.20 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 403953
15.20 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470396
15.75 15.94 15.39 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 404003
15.39 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470401
15.94 16.14 15.59 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 404053
15.59 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470406
16.14 16.34 15.79 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 404103
15.79 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470411
16.34 16.54 15.94 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 404153
15.94 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470416
16.54 16.73 16.14 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 404203
16.14 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470421
16.73 16.93 16.34 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 404253
16.34 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470426
16.14 17.32 15.04 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 R 404252
15.04 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 V 404256
17.32 18.70 15.94 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 R 404502
15.94 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 V 404506
16.93 18.90 15.94 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 R 404500
15.94 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 V 404504
16.93 17.13 16.54 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 404303
16.54 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470431
17.13 17.32 16.73 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 404353
16.73 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470436

d1 d c b1 b D1 (= d1+) D (= d1 +) B1
over incl. max min
in. in. – – –
17.32 17.52 16.89 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 404403
16.89 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470441
17.52 17.72 17.09 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 404453
17.09 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470446
17.72 17.91 17.28 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 404503
17.28 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470451
17.91 18.11 17.48 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 404553
17.48 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470456
18.11 18.31 17.64 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 404603
17.64 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470461
18.31 18.50 17.83 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 404653
17.83 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470466
18.50 18.70 18.03 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 404703
18.03 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470471
18.70 18.90 18.23 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 404753
18.23 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470476
18.70 20.08 17.72 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 R 405002
17.72 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 V 405006
20.08 21.26 18.58 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 R 405252
18.58 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 V 405256
18.90 20.87 17.72 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 R 405000
17.72 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 V 405004
18.90 19.09 18.43 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 404803
18.43 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470481
19.09 19.29 18.62 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 404853
18.62 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470486
19.29 19.49 18.82 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 404903
18.82 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470491
19.49 19.69 19.02 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 404953
19.02 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470496
19.69 19.88 19.21 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 405003
19.21 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470501
7.2
19.88 20.08 19.41 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 405053
19.41 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470506
20.08 20.28 19.57 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 405103
19.57 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470511
20.28 20.47 19.76 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 405153
19.76 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470516
20.47 20.67 19.96 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 405203
19.96 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470521
20.67 20.87 20.16 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 405253
20.16 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470526
21.26 22.64 19.49 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 R 405502
19.49 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 V 405506

d1 20.87 – 28.74 in.
B1
d D1 d1 D
b1

d1 d c b1 b D1 (= d1+) D (= d1 +) B1
over incl. max min
in. in. – – –
20.87 22.83 19.49 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 R 405500
19.49 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 V 405504
20.87 21.06 20.35 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 405303
20.35 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470531
21.06 21.26 20.51 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 405353
20.51 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470536
21.26 21.46 20.71 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 405403
20.71 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470541
21.46 21.65 20.91 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 405453
20.91 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470546
21.65 21.85 21.10 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 405503
21.10 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470551
21.85 22.05 21.30 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 405553
21.30 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470556
22.05 22.24 21.50 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 405603
21.50 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470561
22.24 22.44 21.65 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 405653
21.65 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470566
22.44 22.64 21.85 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 405703
21.85 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470571
22.64 22.83 22.05 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 405753
22.05 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470576
22.64 24.61 21.26 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 R 406002
21.26 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 V 406006
22.83 24.80 21.26 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 R 406000
21.26 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 V 406004

d1 d c b1 b D1 (= d1+) D (= d1 +) B1
over incl. max min
in. in. – – –
22.83 23.03 22.24 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 405803
22.24 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470581
23.03 23.23 22.44 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 405853
22.44 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470586
23.23 23.62 22.64 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 405903
22.64 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470591
23.62 24.02 22.91 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 406003
22.91 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470601
24.02 24.41 23.31 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 406103
23.31 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470611
24.41 24.80 23.70 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 406203
23.70 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470621
24.21 26.57 23.62 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 R 406502
23.62 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 V 406506
24.80 26.18 23.62 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 R 406500
23.62 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 V 406504
24.80 25.20 24.09 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 406303
24.09 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470631
25.20 25.59 24.45 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 406403
24.45 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470641
25.59 25.98 24.84 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 406503
24.84 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470651
25.98 26.38 25.20 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 406603
25.20 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470661
26.57 27.95 24.80 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 R 407002
24.80 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 V 407006
26.18 27.76 24.80 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 R 407000
24.80 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 V 407004
26.38 26.77 25.59 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 406703
25.59 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470671
26.77 27.17 25.98 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 406803
25.98 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470681
7.2
27.17 27.56 26.38 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 406903
26.38 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470691
27.56 27.95 26.77 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 407003
26.77 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470701
27.95 29.13 26.38 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 R 407252
26.38 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 V 407256
27.76 29.33 26.38 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 R 407250
26.38 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 V 407254
27.95 28.35 27.13 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 407103
27.13 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470711
28.35 28.74 27.52 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 407203
27.52 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470721

d1 28.74 – 39.96 in.
B1
d D1 d1 D
b1

d1 d c b1 b D1 (= d1+) D (= d1 +) B1
over incl. max min
in. in. – – –
28.74 29.13 27.91 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 407303
27.91 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470731
29.13 29.53 28.27 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 407403
28.27 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470741
29.13 30.51 27.76 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 R 407502
27.76 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 V 407506
29.33 30.91 27.76 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 R 407500
27.76 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 V 407504
29.53 29.84 28.66 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 407503
28.66 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470751
29.84 30.16 28.94 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 407603
28.94 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470761
30.16 30.47 29.25 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 407703
29.25 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470771
30.47 30.83 29.57 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 407803
29.57 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470781
30.83 31.18 29.88 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 407903
29.88 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470791
30.51 32.48 29.33 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 R 408002
29.33 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 V 408006
30.91 32.68 29.33 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 R 408000
29.33 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 V 408004
31.18 31.54 30.24 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 408003
30.24 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470801
31.54 31.89 30.59 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 408103
30.59 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470811

d1 d c b1 b D1 (= d1+) D (= d1 +) B1
over incl. max min
in. in. – – –
31.89 32.32 30.94 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 408203
30.94 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470821
32.32 32.72 31.34 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 408303
31.34 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470831
32.48 34.45 30.91 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 R 408502
30.91 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 V 408506
32.68 34.45 30.91 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 R 408500
30.91 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 V 408504
32.72 33.11 31.69 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 408403
31.69 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470841
33.11 33.50 32.05 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 408503
32.05 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470851
33.50 33.90 32.44 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 408603
32.44 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470861
33.90 34.29 32.80 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 408703
32.80 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470871
34.29 34.72 33.19 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 408803
33.19 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470881
34.45 36.42 32.48 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 R 409002
32.48 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 V 409006
34.45 36.22 32.48 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 R 409000
32.48 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 V 409004
34.72 35.12 33.58 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 408903
33.58 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470891
35.12 35.91 34.29 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 409003
34.29 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470901
35.91 36.30 34.65 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 409203
34.65 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470921
36.42 38.39 34.06 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 R 409502
34.06 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 V 409506
36.22 37.99 34.06 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 R 409500
34.06 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 V 409504
7.2
36.30 36.73 35.04 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 409303
35.04 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470931
36.73 37.17 35.43 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 409403
35.43 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470941
37.17 37.60 35.87 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 409503
35.87 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470951
37.60 38.03 36.26 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 409603
36.26 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470961
38.39 40.35 35.83 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 R 410002
35.83 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 V 410006
37.99 39.96 35.83 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 R 410000
35.83 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 V 410004

d1 38.03 – 56.69 in.
B1
d D1 d1 D
b1

d1 d c b1 b D1 (= d1+) D (= d1 +) B1
over incl. max min
in. in. – – –
38.03 38.46 36.69 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 409703
36.69 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470971
38.46 38.90 37.09 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 409803
37.09 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470981
38.90 39.33 37.52 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 409903
37.52 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 470991
39.33 39.76 37.91 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 410003
37.91 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 471001
39.76 40.35 38.31 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 410203
38.31 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 471021
40.35 42.32 37.60 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 R 410502
37.60 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 V 410506
39.96 41.93 37.60 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 R 410500
40.35 41.14 38.98 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 410403
38.98 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 471041
41.14 41.93 39.69 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 410603
39.69 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 471061
42.32 44.29 39.37 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 R 411002
39.37 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 V 411006
41.93 43.90 39.37 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 R 411000
41.93 42.72 40.43 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 410803
40.43 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 471081
42.72 43.50 41.14 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 411003
41.14 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 471101
43.50 44.29 41.93 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 411203
41.93 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 471121
44.29 46.26 41.14 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 R 411502
41.14 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 V 411506

d1 d c b1 b D1 (= d1+) D (= d1 +) B1
over incl. max min
in. in. – – –
43.90 45.87 41.14 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 R 411500
44.29 45.08 42.68 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 411403
42.68 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 471141
45.08 45.87 43.43 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 411603
43.43 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 471161
46.26 48.23 42.91 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 R 412002
42.91 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 V 412006
45.87 47.83 42.91 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 R 412000
45.87 46.65 44.13 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 411803
44.13 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 471181
46.65 47.44 44.84 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 412003
44.84 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 471201
47.44 48.23 45.55 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 412203
45.55 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 471221
48.23 50.20 44.69 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 R 412502
44.69 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 V 412506
47.83 50.00 44.69 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 R 412500
48.23 49.02 46.30 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 412403
46.30 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 471241
49.02 50.00 47.05 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 412603
47.05 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 471261
50.00 50.98 47.95 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 412803
47.95 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 471281
50.20 52.17 46.46 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 R 413002
46.46 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 V 413006
50.00 51.97 46.46 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 R 413000
50.98 51.77 48.82 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 413003
48.82 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 471301
51.77 52.76 49.57 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 413253
49.57 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 471326
52.17 54.13 48.23 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 R 413502 7.2
48.23 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 V 413506
51.97 53.94 48.23 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 R 413500
52.76 53.74 50.43 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 413503
50.43 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 471351
53.74 54.72 51.38 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 413753
51.38 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 471376
54.13 56.10 50.00 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 R 414002
50.00 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 V 414006
53.94 55.91 50.00 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 R 414000
54.72 55.71 52.28 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 414003
52.28 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 471401
55.71 56.69 53.15 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 414253
53.15 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 471426

d1 56.10 – 79.53 in.
B1
d D1 d1 D
b1

d1 d c b1 b D1 (= d1+) D (= d1 +) B1
over incl. max min
in. in. – – –
56.10 58.07 51.77 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 R 414502
51.77 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 V 414506
55.91 57.87 51.77 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 R 414500
56.69 57.68 54.09 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 414503
54.09 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 471451
57.68 58.66 55.00 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 414753
55.00 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 471476
58.07 60.04 53.54 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 R 415002
53.54 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 V 415006
57.87 59.84 53.54 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 R 415000
58.66 59.65 55.87 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 415003
55.87 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 471501
59.65 60.63 56.81 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 415253
56.81 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 471526
60.04 62.01 55.31 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 R 415502
55.31 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 V 415506
59.84 61.81 55.31 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 R 415500
60.63 61.81 57.76 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 415503
57.76 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 471551
61.81 62.99 58.86 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 415753
58.86 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 471576
62.01 63.98 57.09 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 R 416002
57.09 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 V 416006
61.81 63.78 57.09 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 R 416000
62.99 64.57 60.00 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 416003
60.00 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 471601

d1 d c b1 b D1 (= d1+) D (= d1 +) B1
over incl. max min
in. in. – – –
63.98 65.94 58.86 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 R 416502
58.86 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 V 416506
63.78 65.75 58.86 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 R 416500
64.57 66.14 61.38 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 416503
61.38 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 471651
65.94 67.91 60.63 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 R 417002
60.63 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 V 417006
65.75 67.72 60.63 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 R 417000
66.14 67.72 62.83 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 417003
62.83 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 471701
67.91 69.88 62.40 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 R 417502
62.40 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 V 417506
67.72 69.69 62.40 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 R 417500
67.72 69.49 64.25 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 417503
64.25 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 471751
69.49 71.26 65.79 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 418003
65.79 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 471801
69.88 71.85 64.17 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 R 418002
64.17 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 V 418006
69.69 71.65 64.17 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 R 418000
71.26 73.03 67.48 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 418503
67.48 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 471851
71.85 73.82 65.94 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 R 418502
65.94 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 V 418506
71.65 73.62 65.94 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 R 418500
73.03 75.00 69.02 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 419003
69.02 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 471901
73.82 75.79 67.72 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 R 419002
67.72 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 V 419006
73.62 75.59 67.72 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 R 419000
7.2
75.00 76.97 70.63 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 419503
70.63 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 471951
75.79 77.76 69.49 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 R 419502
69.49 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 V 419506
75.59 77.56 69.49 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 R 419500
76.97 79.13 72.60 1.18 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR4 R 420003
72.60 0.83 1.28 2.56 0.94 4.53 1.97 ± 0.47 VR6 R 472001
77.76 79.72 71.26 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 R 420002
71.26 0.26 0.24 0.41 0.20 0.79 0.31 ± 0.06 VR3 V 420006
77.56 79.53 71.26 0.59 0.56 0.98 0.39 1.77 0.79 ± 0.16 VR1 R 420000
V-ring seals
MVR axial shaft seals Design and material

The MVR seals are made of a nitrile rubber
General material with very good wear resistance. Other
For added protection in extremely contaminated elastomers are also available on request.
applications, SKF also offers MVR seals. Like The standard metal element is zinc-plated
V-ring seals, MVR seals also seal axially and cold-rolled carbon steel. Acid-resistant steel,
function by combining lip contact with centrifugal similar to SAE 316, is available on request.
“flinging” action. MVR seals are, however, differ- There are two different MVR seal designs:
ent from V-rings in that their rubber element is the basic MVR1 seal and the MVR2 seal with
stretch fit into a metal case. The metal case is case extension († fig. 12).
then press fit onto the shaft. The case provides
excellent protection from heavy debris and ena-
bles the seal to accommodate high rotational Temperature range
speeds without requiring auxiliary clamping The permissible operating temperature range
devices. is between –30 and +100 °C (–20 and +210 °F).
MVR seals are used in rotating shaft appli
cations such as gearboxes, speed reducers,
saws, lathes, motors, mixers, where high levels Sizes
of contaminants reduce the service life of radial MVR seals are available for shaft diameters
shaft seals and bearings. MVR seals can also ranging from 10 to 200 mm (0.394 to 7.874 in.).
serve as primary seals to retain high-viscosity Contact your SKF sales representative for com-
lubricants or exclude contaminants in prehensive information on available sizes.
dry-running applications.
Advantages and user benefits

• The metal case serves as a support and
deflector, protecting the rubber body and lip
from damage and displacement by external
debris like rocks and aggressive media.
• The case also often functions as a holder that
keeps the rubber lip in position in high-speed
applications. No additional axial retention is
required.
• Narrow installation widths are possible thanks
to the compact design.
• Frictional heat build-up and torque drag are
very low compared to those of contacting
radial shaft seals. As rotational speed increases,
the MVR sealing lip lifts off the counterface
surface starting at about 12 m/s (2 360 ft/min)
and drops to zero contact by 20 m/s
Fig. 12
(3 900 ft/min). The high rotational speed
helps exclude contaminants while minimizing
power loss.
• The service life of MVR seals is considerably
higher than that of radial shaft seals in con-
taminated environments and can extend to
thousands of hours.
MVR1 MVR2
Installation Fig. 13
The inside diameter of MVR seals is machined Installation tool for MVR1
for a press fit on the shaft († figs. 13 and 14). B
As with radial shaft seals, do not hit the metal
case with a hammer.
The sealing lip face should be lightly greased
prior to installation, but no grease should be
applied between the lip and case. A shaft finish
of Ra 4 µm (160 µin.) is sufficient.
A lead-in chamfer should be provided. No
splines or keyways are allowed.
Counterface surfaces for MVR seals should
be prepared the same way as for V-rings. Avoid
aluminium or soft metals in applications where
there will be abrasive contaminants. Sharp
peaks on turned surfaces should be removed.
Fig. 14
Installation tool for MVR2
Metal-cased V-ring seals – MVR1 – metric dimensions

d1 10 – 135 mm
B1
B3
d1 h9
c
D1
Shaft Case outside Seal fitted Gap Max. counterface
diameter diameter width width hole diameter
d1 c B1 B3 D1
mm –
10 24 3,5 1,0 15 MVR1-10

12 26 3,5 1,0 17 MVR1-12
15 30 4,0 1,0 21 MVR1-15
16 32 4,0 1,0 23 MVR1-16
17 32 4,0 1,0 23 MVR1-17
18 33 4,0 1,0 24 MVR1-18

20 35 4,0 1,0 26 MVR1-20
22 40 4,0 1,0 28 MVR1-22
24 40 4,0 1,0 30 MVR1-24
25 40 4,0 1,0 31 MVR1-25
26 40 4,0 1,0 32 MVR1-26

28 43 4,0 1,0 34 MVR1-28
30 47 4,5 1,0 37 MVR1-30
32 49 4,5 1,0 39 MVR1-32
35 52 4,5 1,0 42 MVR1-35
40 57 4,5 1,0 47 MVR1-40

45 62 4,5 1,0 52 MVR1-45
48 65 4,5 1,0 55 MVR1-48
50 70 5,5 1,0 58 MVR1-50
52 72 5,5 1,0 60 MVR1-52
53 73 5,5 1,0 61 MVR1-53

55 75 5,5 1,0 63 MVR1-55
58 78 5,5 1,0 66 MVR1-58
60 80 5,5 1,0 68 MVR1-60
62 82 5,5 1,0 70 MVR1-62
65 85 5,5 1,0 73 MVR1-65

68 88 5,5 1,0 76 MVR1-68
70 90 5,5 1,0 78 MVR1-70
72 92 5,5 1,0 80 MVR1-72
75 95 5,5 1,0 83 MVR1-75
Special designs are available and new sizes are added gradually.
Shaft Case outside Seal fitted Gap Max. counterface
diameter diameter width width hole diameter
d1 c B1 B3 D1
mm –
78 98 5,5 1,0  
86 MVR1-78
80 100 5,5 1,0  
88 MVR1-80
85 105 5,5 1,0  
93 MVR1-85
90 110 5,5 1,0  
98 MVR1-90
95 115 5,5 1,0 103 MVR1-95
100 120 5,5 1,0 108 MVR1-100

105 125 5,5 1,0 113 MVR1-105
125 148 6,5 1,0 133 MVR1-125
135 159 6,5 1,0 145 MVR1-135
7.3
Metal-cased V-ring seals – MVR2 – metric dimensions

d1 15 – 100 mm
B2
B1
b
t
B3
d1 h9
c D D
D1 2 3
Shaft Case outside Seal fitted Gap Total seal Case groove Seal counter Case groove diameter Metal case
diameter diameter width width case width width face hole inside outside thickness
d1 c B1 B3 b B2 D1 D2 D3 t
max
mm –
15 32 4,0 1,0 6,0 3 21 29 34 0,5 MVR2-15

17 34 4,0 1,0 6,0 3 23 31 36 0,5 MVR2-17
20 37 4,0 1,0 6,0 3 26 34 39 0,5 MVR2-20
25 42 4,0 1,0 6,0 3 31 39 44 0,5 MVR2-25
30 48 4,5 1,0 6,5 3 37 45 50 0,5 MVR2-30
35 53 4,5 1,0 6,5 3 42 50 55 0,5 MVR2-35

40 58 4,5 1,0 6,5 3 47 55 60 0,5 MVR2-40
45 63 4,5 1,0 6,5 3 52 60 65 0,5 MVR2-45
50 72 5,5 1,0 7,5 3 58 68,5 74 0,75 MVR2-50
55 77 5,5 1,0 7,5 3 63 73,5 79 0,75 MVR2-55
60 82 5,5 1,0 7,5 3 68 78,5 84 0,75 MVR2-60

65 87 5,5 1,0 7,5 3 73 83,5 89 0,75 MVR2-65
70 92 5,5 1,0 7,5 3 78 88,5 94 0,75 MVR2-70
75 95 5,5 1,0 7,5 3 83 93,5 99 0,75 MVR2-75
80 102 5,5 1,0 7,5 3 88 98,5 104 0,75 MVR2-80
85 107 5,5 1,0 7,5 3 93 103,5 109 0,75 MVR2-85

90 112 5,5 1,0 7,5 3 98 108,5 114 0,75 MVR2-90
95 117 5,5 1,0 7,5 3 103 113,5 119 0,75 MVR2-95
100 122 5,5 1,0 7,5 3 108 118,5 124 0,75 MVR2-100
7.4
www.nguyenxuong.com
Axial clamp seals
General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 472
Designs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 472
Design of the sealing arrangement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 473
Installation instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 474

8.1 Product table: CT1 and CT4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 476
Axial clamp seals
General Designs
SKF axial clamp seals are designed for large and SKF axial clamp seals are manufactured in two
very large shaft diameters. They are suitable for different designs:
use as primary seals or as secondary seals in
applications where the primary seals are sub- • CT1 seals († fig. 1) have the basic design
jected to excessive solid or fluid contaminants. and are held in position by a band clamp. The
Axial clamp seals do not rotate but seal axially maximum permissible axial displacement
against a rotating counterface. relative to the counterface is +2,4 mm
SKF axial clamp seals are made of profiled (0.094 in.).
strips of non-reinforced nitrile rubber and are • CT4 seals († fig. 1) are extra wide and are
held firmly in position by stainless steel band designed with two band clamps. The maximum
clamps. They are available for shaft diameters axial displacement relative to the counterface
ranging from 150 to 4 600 mm (5.9 to 181 in.). is +4,8 mm (0.189 in.).
The standard range of SKF axial clamp seals
is intended for inch-size shaft diameters. Be-
cause axial clamp seals are typically installed
with an approximate 25 mm (0.984 in.) gap
between the ends, they may also be used for
metric shaft diameters.
Fig. 1
Axial clamp seal designs
CT1 CT4
Design of the sealing Typically, after installation, CT axial clamp

arrangement seals have an approximate 25 mm (1 in.) gap
between the ends. This should be arranged at the
To obtain reliable sealing performance, the seal 6 o’clock position († fig. 2 on page 474) to facili
seat diameter (d1), seal seat width (b1) and the tate installation and drainage of contaminants.
seal fitted width (B1) should meet the require- Butt-joint seals are also available for certain
ments listed in table 1. SKF also recommends applications.
that the seal should abut a shoulder to simplify
alignment.
Finely turned counterfaces are adequate
for axial clamp seals. The appropriate surface
roughness values are Ra 2,5 μm (115 μin.)
and Rt 12 μm (480 μin.).
Table 1
Application tolerances
B1
c1
d1
b1 B3
Dimension Tolerance Axial clamp seals

CT1 CT4
Seal seat diameter, d1 mm ±1,6 152,40 – 4 572 304,80 – 1 143

in. ± 0.063 6.000 – 180.000 12.000 – 45.000
Seal fitted width, B1 mm ±0,8 28,60 – 38,10 38,10 – 92,20

in. ± 0.031 1.125 – 1.500 1.500 – 3.750
Seal seat width, b1 mm ±3,2 17,50 – 27 27 – 84

in. ± 0.125 0.688 – 1.063 1.063 – 3.313
Lip height, c1 mm ±0,8 12,70 12,70

in. ± 0.031 0.500 0.500
Gap width, B3 (max) mm

in.
11,10
0.437
11,10
0.437
8
Axial clamp seals
Installation instructions
Axial clamp seals are supplied as rolled-up coils.
They are placed in position on their seat in the
housing and bolted lightly together. They are
then pushed forward toward the counterface
and the gap (or joint) between the two ends is
arranged at the 6 o’clock position († fig. 2). The
clamps are finally tightened. The torque applied
to the clamp screws should not exceed 7 Nm.
Fig. 2
Sealing arrangement and installation
A
A–A
Axial clamp seals – CT1 and CT4 – metric dimensions (converted from inch dimensions)
d1 168 – 1 080 mm
B1 B1
d1 b1 d1 b1
CT1 CT4
See table 1, page 473 for application tolerances.
Dimensions Design Designation Dimensions Design Designation

Seal seat Seal fitted Seal seat Seal seat Seal fitted Seal seat
diameter width width diameter width width
d1 B1 b1 d1 B1 b1
mm – – mm – –
168 28,60 17,50 CT1 594334 381 28,60 17,50 CT1 594025
168,30 28,60 17,50 CT1 529489 387 28,60 17,50 CT1 594954
178 38,10 27 CT1 523586 410 23,80 12,70 CT1 595110
185 30 18,90 CT1 593637 413 88,90 77,80 CT4 592934
209,60 28,60 17,50 CT1 527820 425 31,80 20,70 CT1 523826
33,40 22,30 CT1 524815
219 28,60 17,50 CT1 529490
432 38,10 27 CT1 528535
227 28,60 17,50 CT1 531635
444,50 34,90 23,80 CT1 525737
228,60 28,60 17,50 CT1 524204
28,60 17,50 CT1 527819 445 31,80 20,70 CT1 522679
34,90 23,80 CT1 523547
229 29 17,90 CT1 528631
449,30 95,30 84,20 CT4 528070
254 28,60 17,50 CT1 524205
28,60 17,50 CT1 527806 470 28,60 17,50 CT1 525708
31,80 20,70 CT1 526192
273 28,60 17,50 CT1 594369
495 28,60 17,50 CT1 594181
280 28,60 17,50 CT1 524206
31,80 20,70 CT1 524928 508 31,80 20,70 CT1 524587
298,40 28,60 17,50 CT1 593629 533 32 20,90 CT1 594241
305 31,80 20,70 CT1 524208 546 31,80 20,70 CT1 524599
38,10 27 CT1 525582 95,30 84,20 CT4 526741
330 28,60 17,50 CT1 524209 554 31,80 20,70 CT1 524210
38,10 27 CT1 523587
557 28,60 17,50 CT1 524211
350,80 38,10 27 CT1 594110
559 31,80 20,70 CT1 524347
355,60 38,10 27 CT1 530733
34,90 23,80 CT1 593037 571,50 31,80 20,70 CT1 524212
380 38,10 27 CT1 593171 578 34,90 23,80 CT1 524657

d1 B1 b1 d1 B1 b1
mm – – mm – –
594 34,90 23,80 CT1 525627 876 38,10 27 CT1 523063
595 28,60 17,50 CT1 525031 889 31,80 20,70 CT1 524220
597 34,90 23,80 CT1 524364 900 31,80 20,70 CT1 524221
600 30 18,90 CT1 594431 902 38,10 27 CT1 524222
603 31,80 20,70 CT1 524365 914 28,60 17,50 CT1 528416
34,90 23,80 CT1 523184 30,20 19,10 CT1 524223
46 34,90 CT4 528651 38,10 27 CT1 524224
603,30 34,90 23,80 CT1 525637 914,40 28,60 17,50 CT1 593606
46 34,90 CT4 528267 31,80 20,70 CT1 530466
616 47,60 36,50 CT4 529276 929 28,60 17,50 CT1 593285
75,20 64,10 CT4 594202
629 31,80 20,70 CT1 524213
937 34,90 23,80 CT1 523154
638 34,90 23,80 CT1 524214
940 38,10 27 CT1 525320
655 40 28,90 CT4 594784
943 31,80 20,70 CT1 524768
660 34,90 23,80 CT1 524591
946 31,80 20,70 CT1 524368
684 28,60 17,50 CT1 524215
73 61,90 CT4 593604 949 31,80 20,70 CT1 526246
692 34,90 23,80 CT1 524592 952 31,80 20,70 CT1 526582
705 34,90 23,80 CT1 524216 962 31,80 20,70 CT1 524225
60,30 49,20 CT4 528268
965 31,80 20,70 CT1 524226
711 31,80 20,70 CT1 527232
1 003 28,60 17,50 CT1 529452
732 28,60 17,50 CT1 525032 31,80 20,70 CT1 526806
737 38,10 27 CT1 524940 1 013 34,90 23,80 CT1 523584

44,50 33,40 CT4 528269 36,50 25,40 CT1 529379
746 38,10 27 CT1 524853 1 016 36,50 25,40 CT1 525035

39,70 28,60 CT4 528270 38,10 27 CT1 527903
755 34,90 23,80 CT1 524217 1 018 54,80 43,70 CT4 530396
38,10 27 CT1 524218
1 022 31,80 20,70 CT1 525426
755,70 38,10 27 CT1 524973
1 029 38,10 27 CT1 528532
764 28,60 17,50 CT1 525033
1 038 38,10 27 CT1 525633
787 31,80 20,70 CT1 525212
1 041 38,10 27 CT1 524227
800 31,80 20,70 CT1 528210
1 045 38,10 27 CT1 525036
806 31,80 20,70 CT1 526715
818 31,80 20,70 CT1 525034

1 051 33,40 22,30 CT1 530448
8.1
1 054 31,80 20,70 CT1 527474
819,20 31,80 20,70 CT1 524294 38,10 27 CT1 524228
822,30 31,80 20,70 CT1 593949 1 064 41,30 30,20 CT4 528272
825 28,60 17,50 CT1 594785 1 066 63,50 52,40 CT4 528271
31,80 20,70 CT1 524367
1 066,90 38,10 27 CT4 594494
840 31,80 20,70 CT1 526867
1 080 28,60 17,50 CT1 523133
856 31,80 20,70 CT1 524219
Axial clamp seals – CT1 and CT4 – metric dimensions (converted from inch dimensions)
d1 1 101,70 – 4 142 mm
B1 B1
d1 b1 d1 b1
CT1 CT4

d1 B1 b1 d1 B1 b1
mm – – mm – –
1 101,70 31,80 20,70 CT1 524909 1 321 38,10 27 CT1 528927
1 105 38,10 27 CT1 524369 1 346 31,80 20,70 CT1 528526
1 118 31,80 20,70 CT1 524370 1 397 31,80 20,70 CT1 526807
34,90 23,80 CT1 528415
38,10 27 CT1 524229 1 448 31,80 20,70 CT1 528525
38,10 27 CT1 593180
44,50 33,40 CT4 528002 1 497,60 41,30 30,20 CT4 594163
44,50 33,40 CT4 528273
1 613 31,80 20,70 CT1 526808
1 140 38,10 27 CT1 522676
1 721 31,80 20,70 CT1 528975
1 181 31,80 20,70 CT1 529086
1 778 31,80 20,70 CT1 526809
1 193,80 38,10 27 CT1 527211
1 803 31,80 20,70 CT1 524373
1 206 31,80 27 CT1 525091
34,90 23,80 CT1 526021 1 854 38,10 27 CT1 531456
38,10 27 CT1 524230
1 924 31,80 20,70 CT1 525092
1 206,50 30,20 19,10 CT1 530606
1 968 31,80 20,70 CT1 529517
1 210 38,10 27 CT1 522677
2 540 38,10 27 CT1 522856
1 225 38,10 27 CT1 524231
2 616 31,80 20,70 CT1 594083
1 241 38,10 27 CT1 524371
4 142 31,80 20,70 CT1 594682
1 245 31,80 20,70 CT1 522828
1 270 34,90 23,80 CT1 529129
1 286 31,80 20,70 CT1 525953
1 302 34,90 23,80 CT1 529130
1 308 31,80 20,70 CT1 524372

34,90 23,80 CT1 530661
38,10 27 CT1 524232
Axial clamp seals – CT1 and CT4 – inch dimensions

d1 6.614 – 29.016 in.
B1 B1
d1 b1 d1 b1
CT1 CT4

d1 B1 b1 d1 B1 b1
in. – – in. – –
6.614 1.126 0.689 CT1 594334 18.504 1.126 0.689 CT1 525708
6.626 1.126 0.689 CT1 529489 18.504 1.252 0.815 CT1 526192
7.008 1.500 1.063 CT1 523586 19.488 1.126 0.689 CT1 594181
7.284 1.181 0.744 CT1 593637 20.000 1.252 0.815 CT1 524587
8.252 1.126 0.689 CT1 527820 20.984 1.260 0.823 CT1 594241
8.622 1.126 0.689 CT1 529490 21.496 1.252 0.815 CT1 524599
8.937 1.126 0.689 CT1 531635 21.496 3.752 3.315 CT4 526741
9.000 1.126 0.689 CT1 524204 21.811 1.252 0.815 CT1 524210
9.000 1.126 0.689 CT1 527819 21.929 1.126 0.689 CT1 524211
9.016 1.142 0.705 CT1 528631 22.008 1.252 0.815 CT1 524347
10.000 1.126 0.689 CT1 524205 22.500 1.252 0.815 CT1 524212
10.000 1.126 0.689 CT1 527806 22.756 1.374 0.937 CT1 524657
10.748 1.126 0.689 CT1 594369 23.386 1.374 0.937 CT1 525627
11.024 1.126 0.689 CT1 524206 23.426 1.126 0.689 CT1 525031
11.024 1.252 0.815 CT1 524928 23.504 1.374 0.937 CT1 524364
11.748 1.126 0.689 CT1 593629 23.622 1.181 0.744 CT1 594431
12.008 1.252 0.815 CT1 524208 23.740 1.252 0.815 CT1 524365
12.008 1.500 1.063 CT1 525582 23.740 1.374 0.937 CT1 523184
12.992 1.126 0.689 CT1 524209 23.740 1.811 1.374 CT4 528651
12.992 1.500 1.063 CT1 523587 23.752 1.374 0.937 CT1 525637
13.811 1.500 1.063 CT1 594110 23.752 1.811 1.374 CT4 528267
14.000 1.500 1.063 CT1 530733 24.252 1.874 1.437 CT4 529276
14.000 1.374 0.937 CT1 593037 24.764 1.252 0.815 CT1 524213
14.961 1.500 1.063 CT1 593171 25.118 1.374 0.937 CT1 524214
15.000 1.126 0.689 CT1 594025 25.787 1.575 1.138 CT4 594784
15.236 1.126 0.689 CT1 594954 25.984 1.374 0.937 CT1 524591
8.1
16.142 0.937 0.500 CT1 595110 26.929 1.126 0.689 CT1 524215
16.260 3.500 3.063 CT4 592934 26.929 2.874 2.437 CT4 593604
16.732 1.252 0.815 CT1 523826 27.244 1.374 0.937 CT1 524592
16.732 1.315 0.878 CT1 524815 27.756 1.374 0.937 CT1 524216
17.008 1.500 1.063 CT1 528535 27.756 2.374 1.937 CT4 528268
17.500 1.374 0.937 CT1 525737 27.992 1.252 0.815 CT1 527232
17.520 1.252 0.815 CT1 522679 28.819 1.126 0.689 CT1 525032
17.520 1.374 0.937 CT1 523547 29.016 1.500 1.063 CT1 524940
17.689 3.752 3.315 CT4 528070 29.016 1.752 1.315 CT4 528269
Axial clamp seals – CT1 and CT4 – inch dimensions

d1 29.370 – 163.071 in.
B1 B1
d1 b1 d1 b1
CT1 CT4

d1 B1 b1 d1 B1 b1
in. – – in. – –
29.370 1.500 1.063 CT1 524853 39.488 1.126 0.689 CT1 529452
29.370 1.563 1.126 CT4 528270 39.488 1.252 0.815 CT1 526806
29.724 1.374 0.937 CT1 524217 39.882 1.374 0.937 CT1 523584
29.724 1.500 1.063 CT1 524218 39.882 1.437 1.000 CT1 529379
29.752 1.500 1.063 CT1 524973 40.000 1.437 1.000 CT1 525035
30.079 1.126 0.689 CT1 525033 40.000 1.500 1.063 CT1 527903
30.984 1.252 0.815 CT1 525212 40.079 2.156 1.721 CT4 530396
31.496 1.252 0.815 CT1 528210 40.236 1.252 0.815 CT1 525426
31.732 1.252 0.815 CT1 526715 40.512 1.500 1.063 CT1 528532
32.205 1.252 0.815 CT1 525034 40.866 1.500 1.063 CT1 525633
32.252 1.252 0.815 CT1 524294 40.984 1.500 1.063 CT1 524227
32.374 1.252 0.815 CT1 593949 41.142 1.500 1.063 CT1 525036
32.480 1.126 0.689 CT1 594785 41.378 1.315 0.878 CT1 530448
32.480 1.252 0.815 CT1 524367 41.496 1.252 0.815 CT1 527474
33.071 1.252 0.815 CT1 526867 41.496 1.500 1.063 CT1 524228
33.701 1.252 0.815 CT1 524219 41.890 1.626 1.189 CT4 528272
34.488 1.500 1.063 CT1 523063 41.968 2.500 2.063 CT4 528271
35.000 1.252 0.815 CT1 524220 42.004 1.500 1.063 CT4 594494
35.433 1.252 0.815 CT1 524221 42.520 1.126 0.689 CT1 523133
35.512 1.500 1.063 CT1 524222 43.374 1.252 0.815 CT1 524909
35.984 1.126 0.689 CT1 528416 43.504 1.500 1.063 CT1 524369
35.984 1.189 0.752 CT1 524223 44.016 1.252 0.815 CT1 524370
35.984 1.500 1.063 CT1 524224 44.016 1.374 0.937 CT1 528415
36.000 1.126 0.689 CT1 593606 44.016 1.500 1.063 CT1 524229
36.000 1.252 0.815 CT1 530466 44.016 1.500 1.063 CT1 593180
36.575 1.126 0.689 CT1 593285 44.016 1.752 1.315 CT4 528002
36.575 2.961 2.524 CT4 594202 44.016 1.752 1.315 CT4 528273
36.890 1.374 0.937 CT1 523154 44.882 1.500 1.063 CT1 522676
37.008 1.252 0.815 CT1 526246 46.496 1.252 0.815 CT1 529086
37.008 1.500 1.063 CT1 525320 47.000 1.500 1.063 CT1 527211
37.126 1.252 0.815 CT1 524768 47.480 1.252 1.063 CT1 525091
37.244 1.252 0.815 CT1 524368 47.480 1.374 0.937 CT1 526021
37.480 1.252 0.815 CT1 526582 47.480 1.500 1.063 CT1 524230
37.874 1.252 0.815 CT1 524225 47.500 1.189 0.752 CT1 530606
37.992 1.252 0.815 CT1 524226 47.638 1.500 1.063 CT1 522677
Dimensions Design Designation

Seal seat Seal fitted Seal seat
diameter width width
d1 B1 b1
in. – –
48.228 1.500 1.063 CT1 524231

48.858 1.500 1.063 CT1 524371
49.016 1.252 0.815 CT1 522828
50.000 1.374 0.937 CT1 529129
50.630 1.252 0.815 CT1 525953
51.260 1.374 0.937 CT1 529130

51.496 1.252 0.815 CT1 524372
51.496 1.374 0.937 CT1 530661
51.496 1.500 1.063 CT1 524232
52.008 1.500 1.063 CT1 528927
52.992 1.252 0.815 CT1 528526

55.000 1.252 0.815 CT1 526807
57.008 1.252 0.815 CT1 528525
58.606 1.626 1.189 CT4 594163
63.504 1.252 0.815 CT1 526808
67.756 1.252 0.815 CT1 528975

70.000 1.252 0.815 CT1 526809
70.984 1.252 0.815 CT1 524373
72.992 1.500 1.063 CT1 531456
75.748 1.252 0.815 CT1 525092
77.480 1.252 0.815 CT1 529517

100.00 1.500 1.063 CT1 522856
102.992 1.252 0.815 CT1 594083
163.071 1.252 0.815 CT1 594082
163.071 1.252 0.815 CT1 594082
8.1
Product index
Design Product group Product table Page
CRS1. . . . . . . . . . . . . . . . . . . . . . . . . Radial shaft seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.5 167

CRSA1. . . . . . . . . . . . . . . . . . . . . . . . Radial shaft seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.5 167
CRSH1. . . . . . . . . . . . . . . . . . . . . . . . Radial shaft seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.5 167
CRSHA1. . . . . . . . . . . . . . . . . . . . . . . Radial shaft seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.5 168
CRW1 . . . . . . . . . . . . . . . . . . . . . . . . Radial shaft seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.2 105
CRW5 . . . . . . . . . . . . . . . . . . . . . . . . Radial shaft seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.3 161
CRWA1 . . . . . . . . . . . . . . . . . . . . . . . Radial shaft seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.2 105
CRWA5 . . . . . . . . . . . . . . . . . . . . . . . Radial shaft seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.3 161
CRWH1. . . . . . . . . . . . . . . . . . . . . . . Radial shaft seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.2 113
CRWHA1. . . . . . . . . . . . . . . . . . . . . . Radial shaft seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.2 113
CT1. . . . . . . . . . . . . . . . . . . . . . . . . . Axial clamp seal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.1 468
CT4. . . . . . . . . . . . . . . . . . . . . . . . . . Axial clamp seal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8.1 468
DL. . . . . . . . . . . . . . . . . . . . . . . . . . . Radial shaft seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . * 174

DLA. . . . . . . . . . . . . . . . . . . . . . . . . . Radial shaft seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . * 174
HDDF. . . . . . . . . . . . . . . . . . . . . . . . . Metal face seal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.1 384

HDL. . . . . . . . . . . . . . . . . . . . . . . . . . Radial shaft seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.10 226
HDS1. . . . . . . . . . . . . . . . . . . . . . . . . Radial shaft seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.11 242
HDS1K. . . . . . . . . . . . . . . . . . . . . . . . Radial shaft seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.12 258
HDS2K. . . . . . . . . . . . . . . . . . . . . . . . Radial shaft seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.13 260
HDS7. . . . . . . . . . . . . . . . . . . . . . . . . Radial shaft seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.8 216
HDS7K. . . . . . . . . . . . . . . . . . . . . . . . Radial shaft seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.9 222
HDSA1. . . . . . . . . . . . . . . . . . . . . . . . Radial shaft seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.15 264
HDSA2. . . . . . . . . . . . . . . . . . . . . . . . Radial shaft seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.15 264
HDSB1 . . . . . . . . . . . . . . . . . . . . . . . Radial shaft seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.15 264
HDSB2 . . . . . . . . . . . . . . . . . . . . . . . Radial shaft seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.15 264
HDSD1 . . . . . . . . . . . . . . . . . . . . . . . Radial shaft seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.17 272
HDSD2 . . . . . . . . . . . . . . . . . . . . . . . Radial shaft seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.17 272
HDSE1. . . . . . . . . . . . . . . . . . . . . . . . Radial shaft seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.16 270
HDSE2. . . . . . . . . . . . . . . . . . . . . . . . Radial shaft seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.17 272
HDSF1. . . . . . . . . . . . . . . . . . . . . . . . Radial shaft seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.14 263
HDSH7 . . . . . . . . . . . . . . . . . . . . . . . Radial shaft seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.14 262
HDW1. . . . . . . . . . . . . . . . . . . . . . . . Radial shaft seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.4 165
HM1. . . . . . . . . . . . . . . . . . . . . . . . . . Radial shaft seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.6 179
HM102 . . . . . . . . . . . . . . . . . . . . . . . Radial shaft seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.6 179
HM11 . . . . . . . . . . . . . . . . . . . . . . . . Radial shaft seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.6 187
HMA10 . . . . . . . . . . . . . . . . . . . . . . . Radial shaft seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.6 179
* Product table not available. Contact SKF for more information.

HMA6 . . . . . . . . . . . . . . . . . . . . . . . . Radial shaft seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.6 183
HMA8 . . . . . . . . . . . . . . . . . . . . . . . . Radial shaft seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.6 181
HMS5 . . . . . . . . . . . . . . . . . . . . . . . . Radial shaft seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.1 94
HMSA10. . . . . . . . . . . . . . . . . . . . . . Radial shaft seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.1 94
HS4. . . . . . . . . . . . . . . . . . . . . . . . . . Radial shaft seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.24 302
HSF1. . . . . . . . . . . . . . . . . . . . . . . . . Radial shaft seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.19 276
LDSLV3. . . . . . . . . . . . . . . . . . . . . . . Wear sleeve. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.2 360

LDSLV4. . . . . . . . . . . . . . . . . . . . . . . Wear sleeve. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.2 360
MUD1 . . . . . . . . . . . . . . . . . . . . . . . . Cassette seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . * 322

MUD2 . . . . . . . . . . . . . . . . . . . . . . . . Cassette seal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . * 322
MVR1. . . . . . . . . . . . . . . . . . . . . . . . . V-ring seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.3 466
MVR2. . . . . . . . . . . . . . . . . . . . . . . . . V-ring seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.4 468
SBF. . . . . . . . . . . . . . . . . . . . . . . . . . Radial shaft seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.18 282

SKF Speedi-Sleeve. . . . . . . . . . . . . Wear sleeve. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.1 342
SL . . . . . . . . . . . . . . . . . . . . . . . . . . . Radial shaft seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . * 174
SLA. . . . . . . . . . . . . . . . . . . . . . . . . . Radial shaft seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . * 174
SLS. . . . . . . . . . . . . . . . . . . . . . . . . . Radial shaft seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . * 174
SLX . . . . . . . . . . . . . . . . . . . . . . . . . . Radial shaft seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . * 174
TL1. . . . . . . . . . . . . . . . . . . . . . . . . . Radial shaft seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.6 190

TP. . . . . . . . . . . . . . . . . . . . . . . . . . . Track pin seal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.1 376
TPM. . . . . . . . . . . . . . . . . . . . . . . . . . Track pin seal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.1 376
VR1. . . . . . . . . . . . . . . . . . . . . . . . . . V-ring seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.1 400

VR2. . . . . . . . . . . . . . . . . . . . . . . . . . V-ring seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.1 400
VR3. . . . . . . . . . . . . . . . . . . . . . . . . . V-ring seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.1 403
VR4. . . . . . . . . . . . . . . . . . . . . . . . . . V-ring seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.1 405
VR6. . . . . . . . . . . . . . . . . . . . . . . . . . V-ring seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.1 405
VA . . . . . . . . . . . . . . . . . . . . . . . . . . . V-ring seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.2 428
VE . . . . . . . . . . . . . . . . . . . . . . . . . . . V-ring seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.2 433
VL . . . . . . . . . . . . . . . . . . . . . . . . . . . V-ring seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.2 431
VS . . . . . . . . . . . . . . . . . . . . . . . . . . . V-ring seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.2 428
VRME. . . . . . . . . . . . . . . . . . . . . . . . . V-ring seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7.2 433
X1 . . . . . . . . . . . . . . . . . . . . . . . . . . . Radial shaft seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.7 193

X12 . . . . . . . . . . . . . . . . . . . . . . . . . . Radial shaft seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.7 193
X2 . . . . . . . . . . . . . . . . . . . . . . . . . . . Radial shaft seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.7 193 9
X4 . . . . . . . . . . . . . . . . . . . . . . . . . . . Radial shaft seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.7 193

XH15. . . . . . . . . . . . . . . . . . . . . . . . . Radial shaft seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.7 193
YNSLE. . . . . . . . . . . . . . . . . . . . . . . . Radial shaft seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . * 174

YSL . . . . . . . . . . . . . . . . . . . . . . . . . . Radial shaft seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . * 174
YSLE. . . . . . . . . . . . . . . . . . . . . . . . . Radial shaft seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . * 174
www.nguyenxuong.com
www.skf.com/seals
www.nguyenxuong.com

Catalog Phot Chan Dau SKF PDF

Uploaded by

Copyright:

Available Formats

Catalog Phot Chan Dau SKF PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Catalog Phot Chan Dau SKF PDF

Uploaded by

Copyright:

Available Formats

Industrial shaft seals

Pht chn du, Pht trc SKF of 488.

Quantity Unit Conversion

Length inch 1 mm 0.039 in. 1 in. 25,40 mm

Force pound-force 1N 0.225 lbf. 1 lbf. 4,4482 N

Pressure, pounds per 1 MPa 145 psi 1 psi 6,8948 ¥ 103 Pa

Temperature ° (degree) Celsius tC = 0,555 (tF – 32) Fahrenheit tF = 1,8 tC + 32

® SKF, DURATEMP, SPEEDI-SLEEVE and WAVE are registered

1 Product data – general. . . . . . . . . . . . . . . . . . . . . . . . . 11 1

2 Radial shaft seals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 2

3 Cassette seals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 321 3

4 Wear sleeves. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 327 4

5 Track pin seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 373 5

6 Metal face seals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 379 6

7 V-ring seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 389 7

8 Axial clamp seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 471 8

9 Product index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 482 9

From one simple but inspired solution to a mis-

SKF Solution Factory

Meeting the toughest challenges

Working with SKF IT and

SKF – the knowledge

Our knowledge Design and develop

we combine our technology plat­

sustainable and profitable.

Actuation and motion control

SKF – the knowledge engineering

1 Product data – general. . . . . . . . . . . . . . 11

Industrial shaft seals. . . . . . . . . . . . . . . . 12

2 Radial shaft seals. . . . . . . . . . . . . . . . . . . 47 Seals for general industrial

5 Track pin seals. . . . . . . . . . . . . . . . . . . . . 373

6 Metal face seals. . . . . . . . . . . . . . . . . . . . 379

7 V-ring seals . . . . . . . . . . . . . . . . . . . . . . . 389

8 Axial clamp seals. . . . . . . . . . . . . . . . . . . 471

9 Product index. . . . . . . . . . . . . . . . . . . . . . 482

SKF industrial shaft seals and accessories

Radial shaft seals Axial shaft seals Wear sleeves

Seals for general Track pin seals SKF Speedi-Sleeve

Cassette seals V-ring seals

Axial clamp seals

Product data – general 1

Industrial shaft seals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Profile overview selection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Selection of seal design and material. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Storage and handling of seals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Industrial shaft seals

Industrial shaft seals are used to seal the opening Availability

Radial shaft seals

Axial shaft seals

Profile overview selection

HMS5 HMSA10 CRS1 CRSA1 CRSH1 CRSHA1

CRW1 CRWH1 CRWA1 CRWHA1 CRW5 CRWA5

HDW1 HM14 TL7 X15

Seals for general industrial applications, PTFE sealing lip(s)

SL SLA SLX SLS DL DLA

YSLE YNSLE YSL

Product data – general

Seals for heavy industrial applications

HDS7 HDL HDLA HDS1 HDS2 HDSA1

we combine our technology plat