100%(1)100% found this document useful (1 vote) 3K views5 pagesBar Bending Schedule For Pile Foundation With Calculations
Bar Bending Schedule for Pile Foundation With Calculations
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content,
claim it here.
Available Formats
Download as PDF or read online on Scribd
sweer2019
Bar Bending Schedule for Pils Foundation with Caleulatons
Bar Bending Schedule for Pile Foundation with
Calculations
theconstructor org/stucturaren
a a
pile-foundation-bar-bending-schedule-
20, 2018
To clearly understand the bar bending schedule of a pile foundation, it is
necessary to be familiar about the typical reinforcement details of a pile
foundation. Pile foundation is a common type of deep foundation, used for
supporting heavy loaded structures when the site under consideration have a
very weak soil that is compressible in nature.
Layout of a Typical Pile Foundation
A typical pile foundation arrangement have the load structure supported by a
pile cap, which is in turn supported by several piles as shown in the plan and
front view arrangement in the below figures.
Fig.1: Pile
Foundation OC) O
Arrangement —
Superstructure, Pile
Pile group
Cap and Piles aia
hitps:theconstrucor org/structura-engg/plefoundation-bar-bending-schedule-calculations/20989/ 15 sweer2019
Bar Bending Schedule for Pile Foundation with Caleulatons
Structural Specification and Reinforcement
Details of a Pile Foundation
The figure-2 shows the typical reinforcement details and drawing of a pile
foundation. The details of pile cap are not explained in this article
Fig.2: Pile
Foundation
Details fp
Pile Cap
Cutoff Level
Ld
The whole 4
arrangement
is clearly
understood
from the
figure-2. The A
pile cage has 1
vertical
reinforcement 20
held together
by outer and
inner rings.
The
Reinforcement
in pile
construction ,
include:
Hird Rock or Campletely
Weathered rock
1. Vertical Reinforcement
2. Outer Ring Reinforcement
3. Inner Ring Reinforcement
The above details are mentioned in the figure-3 below. The Outer rings are
provided as helical rings and the inner is circular or spiral ties.
Fig.3: Cross-section details in section A-A of figure-2
The development length ‘Ly’ is provided outside of the column piercing into
the pile cap. The anchorage length to the recommended amount is provided
to the bottom of the column as shown in figure-2.
From the Figure:
hitps:theconstrucororgstructura-engg/plefoundation-bar-bending-schedule-calculations/20989/ 25 sweer2019
Bar Bending Schedule for Pile Foundation with Caleulatons
Concreter.
<-#12-Y20
Spacer
YI6 @ 2000c/c se
‘YS © 200c/e
Length of Pile = 20m
Diameter of Pile = 0.6m
Diameter of
a. Vertical Reinforcement = 20mm — 12nos
b. Outer Helical Ring = 8mm @ 200mm c/e
c. Inner spiral ties = 16mm @ 2000mm c/c
Bottom Length of Anchorage = 300mm
Development Length = 40d
Clear Cover = 75mm
oN
oan
Calculation for Bar Bending Schedule of Pile
Foundation
Step 1: Length of Vertical Reinforcement
In the case of bar bending schedule of a column or a pile, there comes need
for lapping the rods so that the length of pile (20m) is attained. Hence, a
lapping length equal to 5Dd is provided in extra. Therefore,
Total Cutting Length for Vertical Reinforcement = Anchorage Length at
the bottom of the pile + the height of the pile + development length (40d)
+ Lap length (50d) — clear cover provided at the bottom.
ie. Ly = 300 + 20000 + 40d +50d -75 = 300 + 20000+ (40 x 12) + (50 x 12) —
75
hitps:theconstrucororg/structural-engg/plefoundation-bar-bending-schedule-calculations/20989/ 35 sweer2019 Bar Bending Schedule for Pile Foundation with Caleulatons
Total length of vertical reinforcement, L, = 21.3m
Note: During tying the bar, it is recommended to tie at the middle, as tying at
the ends of the bars will be subjected to higher stress values
Step 2: Inner Spacing Ring — Number and Length of
each Ring
Here, we have to determine the length of each inner ring along with their
numbers arranged
The number of rings (Nr)
[Length of the Pile / Spacing] +1
= [2000/2000] +1 = 11 No’s
The circumference of the ring gives the length of each ring. For this the radius
of the ring has to be determined. Given the radius of the pile, the clear cover,
outer ring radius
The radius of the ring = [Radius of the pile — clear cover — diameter: of
outer ring — diameter: of vertical reinforcement:}/2
= [600 ~ 75 ~ 8 - 12)/2= 252.5mm
Hence, Length of ring = 2xpixr
= 2x 3.147 x 252.3 = 1584.4mm = 1.58m
Step 3: Outer Helical Ring - Number and Length of
each ring
For every specification of outer helical ring, the radius of the same have to be
determined.
Radius of Helical Ring Outer = [Diameter of Pile - Clear Covery/2
= [600 -75)/2 = 262.5mm
Length of ring = 2xpixr
= 2x 3.147 x 262.5 = 1648.5mm = 1.65m
The number of rings (Ny
[Length of the Pile / Spacing] + 1
hitps:theconstrucororg/structura-engg/plefoundation-bar-bending-schedule-calculations/20989/ 4s sweer2019
Bar Bending Schedule for Pile Foundation with Caleulatons
= [20000/200] +1 = 101 No’s
Step 4: Bar Bending Schedule
Specification
Vertical Bar
Inner Ring
bar
Outer ring bar
Diameter of
Bars (m)
12
16
No. of
Bars (m)
12
1
101
Length of
rods (m)
213
1.58
1.65
Total
Length
(m)
255.6
17.4
166.65
hitps:theconstrucororgstructura-engg/plefoundation-bar-bending-schedule-calculations/20989/
55
