Ramset Anchoring Chemicals Catalogue

Sales, Orders and Enquiries
Tel: 1300 780 063

Fax: 1300 780 064
Email: [email protected]
Web: www.ramset.com.au
STATE BRANCHES
Anchoring
VICTORIA New South Wales QUEENSLAND
96 Church Street, Richmond 3121 71 Carnarvon Street, Silverwater 2128 281 Montague Road, West End 4101
296-298 Maroondah Highway, 563 Gardeners Road, Mascot 2020 153 Ingham Road, Townsville 4810
& Chemicals
HEAD OFFICE Mooroolbark 3138 77 Munibung Road, Cardiff 2285
296-298 Maroondah Highway
Mooroolbark, Victoria 3138 SOUTH AUSTRALIA ACT WESTERN AUSTRALIA
Tel: 03 9726 6222 115 Sir Donald Bradman Drive, 5/19 Tennant Street, Fyshwick 2609 1/12 Colin Jamieson Drive, Welshpool 6106
Hilton 5033
ITW Construction Systems Australia Pty. Ltd. ABN 48 004 297 009 trading as Ramset™. ™Trademarks of Cetram Pty. Ltd. used under licence by Ramset™ Product Catalogue
© Copyright 2010 RAM/MACACC6/2010
In the interests of product improvement, Ramset™ reserves the right to alter product specifications as required.
Information included in this Product Guide is correct at time of printing.
It is the responsibility of the user to ensure product selected is appropriate for its intended use.
For further technical information go to www.ramset.com.au or contact Ramset™ on the numbers indicated.
Mechanical
Page 3
Anchoring
Chemical
Page 81
Anchoring
Construction
Page 117
Chemicals
www.ramset.com.au 1300 780 063 1
2 www.ramset.com.au 1300 780 063
Mechanical
Anchoring
Ramset™ have been offering mechanical anchors

to the Australian market for nearly 50 years.
During this time, trusted Ramset™ brand names,
like DynaBolt™ and TruBolt™, have become so
renowned for their quality, reliability and
performance that their names have entered into
common language on building sites all over
Australia.
Unlike any direct competitor, Ramset™ develops

and manufactures a significant portion of its product
range in Australia for both local and overseas
markets. Ramset™ also extensively and rigorously
tests the performance of all its anchoring products
here in Australia, in Australian substrates for
Australian applications and conditions to ensure
the supply of accurate information required for
anchor design, selection and safe installation
purposes, in Australia.
This Product Guide is designed to provide

information to assist in the selection, ordering
and installation of the appropriate Ramset™
mechanical anchor for general anchoring
applications. It has been divided into six
categorised sections - Heavy Duty Anchors,
Medium Duty Anchors, Light Duty Anchors,
Specialised Anchors, Plasterboard & Cavity
Anchors, and Self Drilling Screws - for ease of use.
For more specific or technical information, or for the
purpose of anchor design and strength limit state
calculations, please refer to the Ramset™
Specifier’s Resource Book.

Mechanical
Anchoring

Contents
Mechanical Anchoring
Anchoring Principles 6
Selection Guide 8
Heavy Duty Anchors 9
• SpaTec™ Plus
• Boa™ Coil
• TruBolt™
Medium Duty Anchors 17

• AnkaScrew™
• DynaBolt™
• Loxin™
• DynaSet™
Light Duty Anchors 31

• RamPlug™
• EasyDrive™
• Nylon Anchors
• ShureDrive™
• RediDrive™
• Concrete Nails
• Plastic Plugs & Spaghetti
Specialised Anchors 47
• AnkaScrew Rod & Stud
™
• TruFast™
• Catenary Wire Eye
• Vertical Flange Clip
• DynaClip™
• InsulFast™ Drill Anchor
Plasterboard & Cavity Anchors 59

• Hollow Wall Anchors
• WallMate™
• ToggleMate™
• Spring Toggle
• RamToggle™
Self Drilling Screws 69

• Plasterboard
• Metal
• Particleboard
• Cabinet
• Cement Sheet

Anchoring Principles
Types of Mechanical Anchor Types of Substrate

Ramset™ offers a number of different types of mechanical anchor. These Ramset™ Mechanical Anchors are suitable for use in a number of different
can be characterised by a combination of their method of setting and their substrates. Please refer to the Selection Guide on page 8 for suitability of
method of anchoring. For example, the Ramset™ DynaBolt™ is described specific anchors to each substrate type.
as a torque setting expansion anchor. Its setting method is torque and its
anchoring method is expansion. The load capacities, depths, spacings and edge distances published in this
guide are recommended only for the substrates specified in the data tables
The various setting and anchoring methods are explained below. for each anchor and are to be used for reference only. Different substrates
may require a different design. Load capacities are also dependent on the
Setting Methods strength of the substrate.

Torque
Torque Setting Anchors, also known as Torque Controlled Anchors, require Should your anchoring scenario vary from the basis of the published data,
the application of a recommended or “controlled” assembly torque, or twist- please consult the Ramset™ Specifiers Resource Book or qualified engineer
ing force, to the nut or bolt head to be correctly set and achieve published for more information.
loads. This is applied and measured with a torque wrench and is checkable
after installation.
Rotation Load Directions

Rotation Setting Anchors are set by rotation. These anchors will achieve Load capacities published in this guide refer to Tensile and Shear. These load
published loads when tight without the need for the application of a directions are defined below.
“controlled” torque.
Tensile (0º ≤ a ≤ 10º)
Displacement
Displacement Setting Anchors, are set by driving a captive expander
component into the bottom end of the anchor, usually with hammer blows, to
a controlled depth that is checkable after anchor installation.
Impact
Impact Setting Anchors are set with hammer blows. They can either be a
Shear (80º ≤ a ≤ 90º)
single element or an anchor with an expander component. The difference
between Impact Setting Anchors and Displacement Setting Anchors is that
Impact Setting Anchors do not require a controlled measure to achieve a set.
Load Assisted
Load Assisted Anchors are set by the application of a tension load. They also
do not require a controlled measure to achieve a set. This type of anchor is
usually only used as a suspension anchor.
If your required load angle is more complex, i.e. a combination of tensile and
shear loads, please consult the Ramset™ Specifiers Resource Book or
Anchoring Methods qualified engineer for more information.
Expansion
Expansion Anchors are generally installed in a pre-drilled hole with a
diameter slightly larger than the outer diameter of the anchor. The anchor’s
diameter is then expanded at the bottom end utilising the appropriate setting
method. This expansion creates a high friction force between the base of Load Classification
the anchor and the wall of the hole. The surrounding substrate contains and Static Load
restricts the expansion forces and holds the anchor in place. An applied load is static when it changes very little over time.
Thread Forming Vibrating Load

Thread Forming Anchors tap their own thread in a pre-drilled hole that is A variable cyclic load of relatively low amplitude and high frequency e.g.
slightly smaller than the outer diameter of the anchor, creating a mechanical motor or fan vibration.
interlock between the anchor and the substrate. This method of anchoring
does not apply expansive forces or burst the substrate, making it suitable for Dynamic Load
close-to-edge or close-to-anchor applications. An irregular variable load of relatively medium or high amplitude e.g. wind.
Interference Fit Shock Load

Interference or Friction Fit Anchors achieve anchorage by applying a friction An isolated high load applied in a very short period of time.
force between the anchor and the wall of the hole along the anchor’s length.
The surrounding substrate contains the forces and holds the anchor in place. These loads can be occasional or permanent.
This anchoring method is usually reserved for light duty applications.
All published data in this guide is based on static load cases. Should your
Deformation load case be classified as anything other than static, please consult the
Deformation Anchors are used for cavity fixing. Anchorage is achieved by Ramset™ Specifiers Resource Book or a Ramset™ engineer for more
changing the shape of the anchor on the inside of the cavity and clamping information.
the anchor body up against the substrate via the appropriate setting method.

Anchor Spacing
Taking into account the stress values created by mechanical anchors and the loads they are designed to support, the following points must be considered
when establishing the performance of each individual product (recommended load):
• The minimum thickness of the base material (bm) (determined by anchor

effective depth hef)
• The minimum distance between anchors (a)
• The distance of anchors from edges of the slab or structure (e)
• The coincidence of stress cones of adjacent anchors in concrete reduces

their tensile performance.
Anchor Effective Depth: hef

Each anchor has a minimum anchorage depth which guarantees its minimum rated load (recommended load). Certain anchor types may be embedded deeper
with a resulting increase in performance.
For further information consult the Ramset™ Specifiers Resource Book.
Reduced Distance Between Anchors

The distance between anchors and from edges and corners can also be reduced in some cases. Such reduction will affect the recommended load of the
anchor and one or more reduction coefficients will have to be applied.
For further information consult the Ramset™ Specifiers Resource Book.

Selection Guide

Aerated Concrete

Cement Sheet
Particleboard
Hollow Block
Plasterboard
Hollow Brick
Steel Purlins
Sheet Metal
Hollow Slab
Solid Stone
Solid Block
Solid Brick
Concrete
Timber
Mechanical Anchor
SpaTec™ Plus Safety Anchors 4 ▲
Boa Coil Expansion Anchors
™
4 ▲
Selection Guide
TruBolt™ Stud Anchors 4 ▲

AnkaScrew Screw-in Anchors ™
4 ▲ 4 4 4 4 4
DynaBolt™ Sleeve Anchors 4 ▲ 4 4 4 4 4
Loxin Shield Anchors ™
4 4 4 4 ● ● ●
DynaSet™ Drop-in Anchors 4 ▲
RamPlug Nylon Frame Anchors ™
4 4 4 4 4 4 4 4
EasyDrive™ Nylon Drive Anchors 4 4 4 4 4 4 4 4
Nylon Anchors 4 4 4 4
ShureDrive™ Drive Anchors 4 4 4 4 4 4 4
RediDrive Hammer-in Anchors ™
4 ▲
Concrete Nails 4 ▲ 4
Plastic Plugs 4 4 4 4 ● ● ●
Plastic Spaghetti 4 4 4 4 ● ● ●
TruFast Suspension Anchors ™
4 ▲
Catenary Wire Eye 4 ▲
AnkaScrew Rod & Stud ™
4 ▲ 4 4 4 4 4
Vertical Flange Clip 4
DynaClip Spring Steel Clip
™
4
InsulFast™ Drill Anchor 4 4 4 4
Hollow Wall Anchors 4 4 4 4
WallMate™ Plasterboard Anchor 4 4
ToggleMate Plasterboard Anchor ™
4
RamToggle™ Cavity Fasteners 4
Spring Toggle Cavity Fasteners 4
Plasterboard Self Drilling Screws 4 4* 4
Metal Self Drilling Screws 4
Particleboard Self Drilling Screws 4 4
Cabinet Self Drilling Screws 4 4
Cement Sheet Self Drilling Screws 4 4 4
* Light guage steel only
4 Recommended ● Recommended with care ▲ Site tests should be implemented

Heavy Duty
Anchors
Heavy Duty Anchors

SpaTec™ Plus
Safety Anchors
Low profile hex or

Countersunk head
Heavy Duty Anchors
Patented anti-rotation expansion

sleeve with pull-down section
High tensile class 8.8 bolt with and locking barbs
extra thick-walled spacer and
maximum fixture thickness indicator
Description
The SpaTec™ Plus Safety Anchor is a heavy duty, torque controlled expansion
anchor, with an integrated pull-down section, designed for high performance
in both static and dynamic load applications, in both cracked and
non-cracked concrete~. The SpaTec™ Plus is ideally suited for through fixing
into concrete when security and reliability are paramount.
~
Whether a concrete element is classified as cracked or non-cracked is to be determined
by a qualified structural engineer.
Specification
Material - Bolt Class 8.8 High Tensile Carbon Steel
( 316 (A4) Stainless Steel available to order )
Corrosion Protection Zinc Plating
Head Styles Hex or Countersunk. (SP16145ESS-Hex Nut)
Fixing Method Through Fixture
Setting Method
Anchoring Method
Torque Controlled
Expansion
Features & Benefits
• The combination of a high tensile class 8.8 bolt with an extra thick-walled
Thread Diameters M10, M12, M16, M20
spacer allows a smaller diameter bolt to be used for easier installation
Drilled Hole Diameters 15mm,18mm, 24mm, 28mm
while still providing both excellent tensile and shear performance. The
Anchor Lengths 105mm, 110mm, 120mm, 130mm,
spacer also incorporates a visual maximum fixture thickness indicator for
145mm, 170mm
ease of use.
Maximum Fixture Thickness’ 10mm, 20mm, 25mm, 27mm, 40mm
• The patented anti-rotation expansion sleeve is designed with sharp angled
Indicative Working Max Tensile 16.7kN - 46.0kN
protrusions that grip the sides of the hole, preventing anchor rotation
Loads in 32MPa Concrete* Max Shear 19.3kN - 75.8kN
during installation. As expansion of the sleeve begins, the locking barbs
Substrates Concrete
also grip the sides of the hole, further embedding as expansion
* Refer to load table
progresses, giving extra holding power. The sleeve pulls down during
Related Products tightening ensuring excellent pressure between the fixture and the
DynaDrill™ Hole Cleaning Brush concrete.
Carbide Drill Bits Hole Cleaning Pump • The low profile hex or countersunk heads provide a neat finish.
Diamond Motor Wet and Dry Vacuum
Diamond Core Drill Bits

SpaTec™ Plus
Safety Anchors
Trades & Applications

Steel Maintenance Plumbing Electrical Construction Elevator
Fabricator Fitter Contractor Contractor Contractor Installer
Anchoring structural steel columns/beams 4
Anchoring HVAC units 4 4
Machinery hold down 4
Anchoring crane rails 4
Anchoring Elevator Guide Rails 4
Installation
Heavy Duty Anchors

1. Drill or core a hole to the recommended diameter and depth using the
fixture as a template. Clean the hole thoroughly with a hole cleaning brush.
Remove the debris with a hand pump, compressed air, or vacuum.
2. After ensuring that the anchor is assembled correctly, insert the anchor
through the fixture and drive with a hammer until the washer contacts
the fixture.
3. Tighten the bolt with a torque wrench to the specified assembly torque.
SpaTec™ Plus Safety Anchors - Hex Bolt - Zinc Plated

Part No Thread Max Fixture Overall Anchor Drilled Hole Fixture Hole Min Hole Effective Order
Size Thickness (mm) Length (mm) Ø (mm) Ø (mm) Depth (mm) Length (mm) Qty
SP10105 M10 20 105 15 17 95 90 25
SP12105 M12 10 105 18 20 95 90 25
SP12120 M12 25 120 18 20 115 105 25
SP16145 M16 25 145 24 26 135 125 10
SP20170 M20 25 170 28 30 165 150 5
SpaTec™ Plus Safety Anchors - Countersunk Head - Zinc Plated

SP10105F M10 27 105 15 17 95 97 25
SP12120F M12 40 130 18 20 105 120 10
Available to order.
Lead times apply.
SpaTec™ Plus Safety Anchors - Hex Bolt - Stainless Steel Grade AISI 316 (A4)
SP10110SS M10 25 110 15 17 100 90 25
SP12120SS M12 25 120 18 20 120 105 25
SP16145ESS* M16 25 145 24 26 130 125 10
*Hex nut assembly
SpaTec™ Plus Safety Anchors - Indicative Working Loads in 32MPa Concrete

Thread Embedment Tightening Min Edge Min Anchor Max Tensile Max Shear
Size Depth (mm) Torque (Nm) Distance (mm) Spacing (mm) Load, Na (kN)* Load, Va (kN)*
M10 80 50 120 240 16.7 19.3
M12 95 80 145 285 22.6 27.6
M16 115 120 175 345 32.4 52.3
M20 140 200 210 420 46.0 75.8
*The design engineer should ensure the structural element is capable of supporting these loads.
Refer to Ramset™ Specifiers Resource Book for more information or explanation of technical data.

Boa™ Coil
Expansion Anchors
Low profile hex head

Heavy Duty Anchors
Depth set mark
Expansion coil
Description
The Boa™ Coil Expansion Anchor is a removable, high strength, heavy duty,
rotation setting expansion anchor for concrete. The Boa™ is ideally suited for
though fixing into concrete when cast-in performance or clean removal is
required.
Specification
Material - Bolt Carbon Steel
Head Styles Hex
Setting Method Rotation
Anchoring Method Expansion
Drilled Hole Diameters 13mm, 16mm, 19mm
Anchor Lengths 75mm, 85mm, 90mm, 100mm,
115mm, 125mm Features & Benefits
Maximum Fixture Thickness’ 6mm, 12mm, 25mm,30mm, 40mm • High load capacity is achieved due to the expansion coil locking into the
Indicative Working Max Tensile 12.6kN - 19.6kN sides of the hole, when set, to give cast-in type performance.
Loads in 32MPa Concrete* Max Shear 15.4kN - 28.4kN • High clamping load and resistance to cyclic loading result from the pull-
Substrates Concrete down effect achieved through the rotation setting action of the anchor.
* Refer to load table • Low profile hex head provides a neat finish.
• Removal is easy, clean and fast, as the expansion coil stays in the hole
leaving no protruding metal parts to grind off. The bolt can even be re-
used with a new coil.
Related Products
DynaDrill™ Hole Cleaning Pump
Carbide Drill Bits Wet and Dry Vacuum
Diamond Motor Impact Wrench
Diamond Core Drill Bits Boa™ Coils
Hole Cleaning Brush

Boa™ Coil
Expansion Anchors

Steel Concrete Scaffold Maintenance
Fabricator Formworker Contractor Fitter
Installing handrails, balustrades & safety barriers 4
Formwork support 4
Scaffold support 4
Heavy Duty Anchors

Installation
1. Drill or core a hole to the recommended diameter and depth
using the fixture as a template. Clean the hole thoroughly with
a hole cleaning brush. Remove the debris with a hand pump,
compressed air, or vacuum.
2. After ensuring that the anchor is assembled correctly (the coil
tab points up the anchor), insert the anchor through the fixture.
Tap the anchor down to the depth set mark, with a hammer,
and stop.
3. Wind the anchor down, with an appropriately sized spanner or
socket wrench, until the washer is firmly held to the fixture
and stop (5 turns). Ensure washer is tight and snug fit.
4. The Boa™ Coil anchor is ready to take load. (The bolt can be
removed leaving the coil in the hole. To re-insert, follow steps
3 and 4.)
Boa™ Coil Expansion Anchors - Hex Bolt - Zinc Plated

Part No Anchor Max Fixture Overall Anchor Drilled Hole Fixture Hole Min Hole Effective Order
Size (mm) Thickness (mm) Length (mm) Ø (mm) Ø (mm) Depth (mm) Length (mm) Qty
BAC08075 13 12 75 13 14 90 59 50
BAC08100 13 30 100 13 14 100 84 50
BAC10090 16 12 90 16 19 105 71 25
BAC10125 16 40 125 16 19 130 106 25
BAC12085 19 6 85 19 21 105 63 20
BAC12115 19 25 115 19 21 120 93 20
Boa™ Coils Only - Zinc Plated

Coil Only Order
Part No Qty
BAC08 100
BAC10 50
BAC12 50
Boa™ Coil Expansion Anchors - Indicative Working Loads in 32MPa Concrete

Anchor Embedment Torque Min Edge Min Anchor Max Tensile Max Shear
Size Depth (mm) (turns to set) Distance (mm) Spacing (mm) Load, Na (kN)* Load, Va (kN)*
13 75 5 turns 80 160 12.6 15.4
16 90 5 turns 100 200 18.6 26.0
19 80 5 turns 120 230 19.6 28.4

TruBolt™
Stud Anchors
Heavy Duty Anchors
Anchor diameter Anti-rotation expansion sleeve

equals Hole diameter
Description
The TruBolt™ Stud Anchor is a true-to-size, heavy duty, torque controlled
expansion anchor, for permanent anchoring into concrete.
Specification
Material - Bolt Carbon Steel, Stainless Steel 316 (A4)
Corrosion Protection Zinc Plating, Hot Dipped Galvanising
Head Styles Hex Nut
Setting Method Torque Controlled
Thread Diameters M6, M8, M10, M12, M16, M20
Drilled Hole Diameters 6mm, 8mm, 10mm, 12mm, 16mm, 20mm
Anchor Lengths 55mm, 65mm, 75mm, 80mm, 85mm,
90mm, 100mm, 120mm, 125mm, 140mm,
150mm, 160mm, 175mm, 180mm, 215mm Features & Benefits
Maximum Fixture Thickness’ 6mm, 8mm, 10mm, 12mm, 15mm, 20mm, • The TruBolt™ diameter equals the required hole diameter providing
25mm, 30mm, 35mm, 40mm, 45mm, maximum shear capacity for hole size and making drill bit selection simple.
50mm, 65mm, 70mm, 80mm, 90mm, Its cold forged construction ensures superior strength and reliability.
100mm • The anchor design ensures maximum expansion of the sleeve and
Indicative Working Max Tensile 3.4kN - 32.5kN pull-down on the fixture. These actions are both further assisted by the
Loads in 32MPa Concrete* Max Shear 2.8kN - 27.3kN application of load.
Substrates Concrete • The anti-rotation expansion sleeve is designed to grip the sides of the hole,
* Refer to load table preventing anchor rotation during installation.
Related Products
Diamond Motor
Hole Cleaning Brush

TruBolt™
Stud Anchors

Steel Elevator Construction Seating Racking
Fabricator Installer Contractor Contractor Installer
Installing handrails, balustrades & safety barriers 4
Anchoring elevator guide rails 4 4
Staduim seating 4
Pallet racking 4
Heavy Duty Anchors

Installation
1. Drill or core a hole to the recommended diameter (same as the TruBolt™)
and depth using the fixture as a template. Clean the hole thoroughly with a
hole cleaning brush. Remove the debris with a hand pump, compressed air,
or vacuum.
2. Insert the anchor through the fixture and drive with a hammer until the
washer contacts the fixture.
3. Tighten the nut with a torque wrench to the specified assembly torque.
TruBolt™ Stud Anchors - Hex Nut - Zinc Plated

Size Thickness (mm) Length (mm) Ø (mm) Ø (mm) Depth (mm) Length Qty
T06055 M6 15 55 6 8 55 38 100
T06085 M6 45 85 6 8 75 68 100
T06120 M6 80 120 6 8 75 103 50
T06150 M6 110 150 6 8 75 133 100
T06180 M6 140 180 6 8 75 163 100
T08065 M8 12 65 8 10 65 45 50
T08090 M8 40 90 8 10 75 70 50
T10075 M10 12 75 10 12 80 52 50
T10090 M10 30 90 10 12 90 67 50
T10120 M10 50 120 10 12 100 97 20
T12080 M12 6 80 12 15 90 58 20
T12100 M12 25 100 12 15 105 71 20
T12120 M12 45 120 12 15 105 93 20
T12140 M12 65 140 12 15 105 111 20
T12180 M12 100 180 12 15 125 151 20
T16100 M16 8 100 16 19 115 67 20
T16125 M16 20 125 16 19 135 85 20
T16150 M16 45 150 16 19 145 110 20
T16175 M16 70 175 16 19 145 135 20
T20120 M20 10 120 20 24 140 85 10
T20160 M20 35 160 20 24 170 115 10
T20215 M20 90 215 20 24 200 170 10

TruBolt™
Stud Anchors
TruBolt™ Stud Anchors - Hex Nut - Hot Dipped Galvanised

Heavy Duty Anchors
T08090GH M8 40 90 8 10 75 70 50
T10090GH M10 30 90 10 12 90 67 50
T12080GH M12 6 80 12 15 90 58 20
T12100GH M12 25 100 12 15 105 71 20
T12140GH M12 65 140 12 15 105 111 20
T12180GH M12 100 180 12 15 125 151 20
T16100GH M16 8 100 16 19 115 67 20
T16125GH M16 20 125 16 19 135 85 20
T16150GH M16 45 150 16 19 145 110 20
T16175GH M16 70 175 16 19 145 135 20
T20120GH M20 10 120 20 24 140 85 10
T20160GH M20 35 160 20 24 170 115 10
T20215GH M20 90 215 20 24 200 170 10
TruBolt™ Stud Anchors - Hex Nut - Stainless Steel Grade AISI 316 (A4)
T06055SS M6 15 55 6 8 55 38 100
T06085SS M6 45 85 6 8 75 68 100
T08065SS M8 12 65 8 10 65 45 100
T08090SS M8 40 90 8 10 75 70 50
T10075SS M10 12 75 10 12 80 52 50
T10090SS M10 30 90 10 12 90 67 50
T12080SS M12 6 80 12 15 90 58 20
T12100SS M12 25 100 12 15 105 71 20
T12140SS M12 65 140 12 15 105 111 20
T16100SS M16 8 100 16 19 115 67 20
T16125SS M16 20 125 16 19 135 85 20
T16150SS M16 45 150 16 19 145 110 20
T16175SS M16 70 175 16 19 145 135 20
T20120SS M20 10 120 20 24 140 85 10
T20160SS M20 35 160 20 24 170 115 10
TruBolt™ Stud Anchors - Indicative Working Loads in 32MPa Concrete

M6 32 10 50 100 3.4 2.8
M8 54 20 80 160 7.2 4.9
M10 72 35 110 220 9.9 6.8
M12 86 50 130 260 12.7 8.6
M16 115 155 170 340 20.9 14.4
M20 145 355 220 440 32.5 27.3

Medium Duty
Anchors
Medium Duty Anchors

AnkaScrew™
Screw-In Anchors
25° thread helix angle provides

reduced setting torque
Medium Duty Anchors
Single self-tapping thread provides

secure anchorage over the full
embedment of the anchor without
bursting the substrate
Hardened high carbon

steel construction
Description
The AnkaScrew™ Screw-In Anchor is a totally removable, medium duty,
rotation setting, thread forming anchor, ideal for either temporary or
permanent anchoring into substrates such as concrete, brick, hollow brick or
block. The AnkaScrew™ is particularly well suited to close-to-edge or close-
to-anchor fixing as it does not expand and burst the surrounding substrate.
Specification
Material High Carbon Steel
Corrosion Protection Zinc Plating, Mechanical Galvanising
Head Style Flanged Hex (5mm & 6mm),
Hex (8mm, 10mm & 12mm)
Anchoring Method Thread Forming
Drilled Hole Diameters 5mm, 6mm, 8mm, 10mm, 12mm Features & Benefits
Anchor Lengths 30mm, 50mm, 60mm, 75mm, • The AnkaScrew™ is both fast and easy to install as it simply screws
100mm, 150mm into a pre-drilled hole.
Maximum Fixture Thickness’ 5mm, 10mm, 15mm, 20mm, 25mm, • The AnkaScrew™ is even faster and easier to remove. It simply screws
35mm, 40mm, 45mm, 50mm, 60mm, out leaving an empty hole with no protruding metal parts to grind off.
70mm, 90mm, 100mm • The AnkaScrew™ is ideal for close-to-edge and close-to-anchor
Indicative Working Max Tensile 1.4kN -14.4kN installation as its self-tapping, rotation setting method of installation is not
Loads in 32MPa Concrete* Max Shear 1.5kN - 16.7kN subject to any expansion pressure, therefore does not burst the substrate.
Substrates Concrete, Solid Brick, Solid Block,
Hollow Block, Hollow Slab, Hollow Brick
* Refer to load table
Related Products
Diamond Motor Impact Wrench
Diamond Core Drill Bits Impact Sockets
Hole Cleaning Brush

AnkaScrew™
Screw-In Anchors

Carpenter Construction Contractor Racking Installer Concrete Formworker
Bottom plates 4
Temporary hand rails/safety barriers 4
Pallet racking 4
Formwork support 4
Medium Duty Anchors

Installation
fixture as a template. Clean the hole thoroughly with a hole cleaning
brush. Remove the debris with a hand pump, compressed air, or vacuum.
2. Insert the AnkaScrew™ through the fixture and screw it into the hole with
either a socket wrench or an impact wrench using slight pressure until the
self-tapping action begins.
3. Tighten the AnkaScrew™ until the fixture is held firm. If resistance is
experienced when tightening, unscrew the anchor one turn and re-tighten.
Ensure that you do not over tighten.
AnkaScrew™ Screw-In Anchors - Zinc Plated & Mechanically Galvanised

Part No. Part No. Anchor Maximum Overall Drilled Hole Fixture Hole Min Hole Effective Order
Zinc Plated Mechanically Size Fixture Anchor Ø Ø Depth Length Qty
Galvanised (mm) Thickness (mm) Length (mm) (mm) (mm) (mm) (mm)
AS05030H - 5 5 30 5 7 30 28 100
AS06050H AS06050HGH 6 20 50 6 8 60 44 100
AS06075H AS06075HGH 6 45 75 6 8 65 69 100
AS06100H AS06100HGH 6 70 100 6 8 65 94 100
AS08060H AS08060HGH 8 20 60 8 10 75 54 100
AS08075H AS08075HGH 8 35 75 8 10 75 69 100
AS08100H AS08100HGH 8 60 100 8 10 80 94 100
AS10060H AS10060HGH 10 10 60 10 12 80 54 50
AS10075H AS10075HGH 10 25 75 10 12 85 69 50
AS10100H AS10100HGH 10 50 100 10 12 95 94 50
AS12075H AS12075HGH 12 15 75 12 14 100 69 50
AS12100H AS12100HGH 12 40 100 12 14 110 94 50
AS12150H AS12150HGH 12 90 150 12 14 110 144 20
AnkaScrew™ Screw-In Anchors - Indicative Working Loads in 32MPa Concrete

nchor Size/
A Embedment Min Edge Min Anchor Max Tensile Max Shear
Hole Ø (mm) Depth (mm) Distance (mm) Spacing (mm) Load, Na (kN)* Load, Va (kN)*
5 25 15 15 1.4 1.5
6 45 25 50 4.1 4.5
8 60 35 70 6.6 8.4
10 75 40 80 9.8 13.8
12 90 50 100 14.4 16.7

DynaBolt™
Sleeve Anchors
Medium Duty Anchors
Multiple Head Styles for a variety of applications
Patented Expansion Sleeve provides

“pull-down” onto fixture
Description
The DynaBolt™ Plus Sleeve Anchor is a medium duty, torque controlled,
expansion anchor, with an integrated pull-down section, designed for medium
duty anchoring of timber and steel fixtures to concrete, brick or block. The
DynaBolt™ Plus is available in a variety of different head styles and finishes.
Specification
Material Carbon Steel, Stainless Steel 316 (A4)
Head Style Hex Nut, Hex Bolt, Countersunk/Flat Head,
Round Head, Hook, Eye, Tie Wire
Thread Sizes M4.5, M6, M8, M10, M12, M16
Drilled Hole Diameters 6mm, 8mm, 10mm, 12mm, 16mm, 20mm Features & Benefits
Anchor Lengths 26mm, 32mm, 34mm, 38mm, 40mm, • The DynaBolt™ Plus patented expansion sleeve closes gaps of up to
41mm, 45mm, 49mm, 55mm, 57mm, 5mm, pulling down on the fixture to induce clamp load and provide
60mm, 62mm, 65mm, 66mm, 70mm, improved security.
75mm, 76mm, 80mm, 81mm, 85mm, • The DynaBolt™ Plus is a fully assembled through fixture anchor.
92mm, 98mm, 100mm, 103mm, 105mm, Therefore, assembly, marking out and re-positioning of fixtures is
106mm, 110mm, 113mm, 124mm, eliminated making installation fast and easy.
125mm, 126mm, 140mm, 157mm • The choice of multiple head styles makes the DynaBolt™ Plus a versatile
Maximum Fixture Thickness’ 3mm, 5mm, 6mm, 8mm, 10mm, 12mm, anchor for a variety of different applications.
15mm, 20mm, 25mm, 30mm, 32mm,
35mm, 45mm, 49mm, 50mm, 55mm,
60mm, 65mm, 70mm, 80mm Related Products
Indicative Working Max Tensile 2.7kN -16.6kN DynaDrill™ Hole Cleaning Brush
Loads in 32MPa Concrete Max Shear 2.5kN - 15.6kN Carbide Drill Bits Hole Cleaning Pump
Substrates Concrete, Solid Brick, Solid Block, Diamond Motor Wet and Dry Vacuum
Hollow Brick, Hollow Block, Hollow Slab Diamond Core Drill Bits Screwdriver Bits

DynaBolt™
Sleeve Anchors

Carpenter Construction Contractor Window Installer Racking Installer
Bottom plates 4
Hand rails 4
Window frames 4
Pallet racking 4
Medium Duty Anchors

Installation
fixture as a template. Clean the hole thoroughly with a hole cleaning
2. Insert the DynaBolt™ Plus through the fixture and drive with a hammer
until the washer contacts the fixture.
3. Tighten the DynaBolt™ Plus, allowing the sleeve to twist and pull down the
fixture firmly onto the substrate. For optimum performance, a torque
wrench should be used.
DynaBolt™ Sleeve Anchor Hex Nut - Zinc Plated

Part No. Thread Max Fixture Overall Anchor Drilled Hole Fixture Hole Min Hole Effective Order
D6026 M4.5 3 26 6 8 30 23 100
DP06040 M4.5 12 38 6 8 45 34 100
DP06060 M4.5 30 57 6 8 55 53 100
DP08040 M6 6 40 8 10 50 34 100
DP08065 M6 25 66 8 10 65 60 50
DP08090 M6 50 92 8 10 75 86 50
DP10040 M8 3 41 10 12 50 34 50
DP10050 M8 20 49 10 12 55 42 50
DP10075 M8 30 76 10 12 65 69 50
DP10100 M8 50 103 10 12 80 96 25
DP10125 M8 80 124 10 12 85 117 25
DP12060 M10 10 55 12 15 70 47 25
DP12070 M10 15 70 12 15 70 62 25
DP12100 M10 45 98 12 15 95 90 20
DP12125 M10 70 126 12 15 95 118 20
DP16065 M12 6 62 16 19 80 51 20
DP16110 M12 35 106 16 19 120 95 10
DP16140 M12 65 140 16 19 120 129 10
DP20080 M16 8 81 20 24 100 70 10
DP20115 M16 25 113 20 24 125 102 5
DP20160 M16 70 157 20 24 155 146 5

DynaBolt™
Sleeve Anchors
DynaBolt™ Sleeve Anchor Hex Nut - Hot Dipped Galvanised

Medium Duty Anchors
Size Thickness (mm) Length (mm) Ø (mm) Hole Ø (mm) Depth (mm) Length (mm) Qty
DP10040GH M8 3 41 10 12 50 34 50
DP10050GH M8 20 49 10 12 55 42 50
DP10075GH M8 30 76 10 12 65 69 50
DP10100GH M8 50 103 10 12 80 96 25
DP12060GH M10 10 55 12 15 70 47 25
DP12070GH M10 15 70 12 15 70 62 25
DP12100GH M10 45 98 12 15 95 90 20
DP12125GH M10 70 126 12 15 95 118 20
DP16065GH M12 6 62 16 19 80 51 20
DP16110GH M12 35 106 16 19 120 95 10
DP16140GH M12 65 140 16 19 120 129 10
DP20080GH M16 8 81 20 24 100 70 10
DP20115GH M16 25 113 20 24 125 102 5
DynaBolt™ Plus Sleeve Anchor Hex Nut - Stainless Steel Grade AISI 316 (A4)
DP06040SS M4.5 12 38 6 8 45 34 100
DP06060SS M4.5 30 57 6 8 55 53 100
DP08040SS M6 6 40 8 10 50 34 100
DP08065SS M6 25 66 8 10 65 60 50
DP10050SS M8 20 49 10 12 55 42 50
DP10075SS M8 30 76 10 12 65 69 50
DP10100SS M8 50 103 10 12 80 96 25
DP12060SS M10 10 55 12 15 70 47 25
DP12070SS M10 15 70 12 15 70 62 25
DP12100SS M10 45 98 12 15 95 90 20
DP12125SS M10 70 126 12 15 95 118 20
DynaBolt™ Sleeve Anchor Hex Bolt - Zinc Plated

DP08045H M6 15 45 8 10 55 34 100
DP08070H M6 32 70 8 10 65 60 50
DP10045H M8 8 45 10 12 55 34 50
DP10055H M8 20 55 10 12 55 42 50
DP10080H M8 30 80 10 12 80 69 50
DP10105H M8 60 105 10 12 85 96 25
DP12065H M10 15 65 12 15 75 47 25
DP12075H M10 20 75 12 15 75 62 25
DP12105H M10 50 110 12 15 95 90 20
DP16110H M12 49 110 16 19 95 95 10

DynaBolt™
Sleeve Anchors
DynaBolt™ Sleeve Anchor Hex Bolt - Stainless Steel Grade AISI 316 (A4)
Medium Duty Anchors

DP08045HSS M6 15 45 8 10 55 34 100
DP08070HSS M6 32 70 8 10 65 60 50
DP10045HSS M8 8 45 10 12 55 34 50
DP10060HSS M8 20 60 10 12 60 56 50
DP10080HSS M8 30 80 10 12 80 69 50
DP10105HSS M8 60 105 10 12 85 96 25
DP12075HSS M10 20 75 12 15 75 62 25
DynaBolt™ Sleeve Anchor Round Head - Zinc Plated

D6032R M4.5 5 32 6 8 40 30 100
DP06055R M4.5 25 55 6 8 50 25 100
DynaBolt™ Sleeve Anchor Countersunk Head - Zinc Plated

D6034F M4.5 10 34 6 8 40 30 100
DP06060F M4.5 30 60 6 8 50 25 100
DP06075F M4.5 45 75 6 8 50 25 100
DP06100F M4.5 70 100 6 8 60 25 100
DP08060F M6 20 60 8 10 70 30 100
DP08085F M6 45 85 8 10 75 30 50
DP10075F M8 30 75 10 12 85 34 50
DP10100F M8 55 100 10 12 85 34 50
DP10125F M8 80 125 10 12 105 34 25
DynaBolt™ Sleeve Anchor Countersunk Head - Stainless Steel Grade AISI 316 (A4)
DP06060FSS M4.5 30 60 6 8 50 25 100
DP06075FSS M4.5 45 75 6 8 50 25 100

DynaBolt™
Sleeve Anchors
DynaBolt™ Sleeve Anchor - Set Lok Bolt - Zinc Plated

Medium Duty Anchors
DO6026S M4.5 - 26 6 - 30 23 500
D06038S M4.5 - 38 6 - 41 34 100
DynaBolt™ Sleeve Anchor - Tie Wire Bolt - Zinc Plated

D08042E M6 - 42 8 - 50 34 100
DynaBolt™ Sleeve Anchor - Hook Bolt - Zinc Plated

D08045K M6 - 47 8 - 55 32 100
DynaBolt™ Sleeve Anchor - Eye Bolt - Zinc Plated

D08045X M6 - 47 8 - 55 32 100
DynaBolt™ Sleeve Anchors - Indicative Working Loads in 32MPa Concrete

Anchor Thread Embedment Tightening Min Edge Min Anchor Max Tensile Max Shear
Size (mm) Size Depth (mm) Torque (Nm) Distance (mm) Spacing (mm) Load, Na (kN)* Load, Va (kN)*
6 M4.5 25 10 55 75 2.7 2.5
8 M6 35 15 60 105 4.2 4.0
10 M8 45 35 70 135 5.9 6.4
12 M10 50 55 75 150 7.7 7.9
16 M12 65 85 100 195 11.9 10.5
20 M16 85 165 130 255 16.6 15.6

DynaBolt™
Decorative Post Heads
DynaBolt™ Decorative Post Head - Tie Wire - Zinc Plated

Medium Duty Anchors

REM06 M6 - 44 - - - - 100
REM08 M8 - 47 - - - - 100
REM10 M10 - 52 - - - - 50
DynaBolt™ Decorative Post Head - Countersunk - Zinc Plated & Stainless Steel 316
DF045SS* M4.5 - 23 - 8 - - 100
RFM06 M6 - 23 - 10 - - 100
DF06SS* M6 - 23 - 10 - - 100
RFM08 M8 - 27 - 12 - - 100
DF08SS* M8 - 27 - 12 - - 100
*Denotes Stainless Steel Grade AISI 316 (A4)
DynaBolt™ Decorative Post Head - Round - Zinc Plated & Stainless Steel 316
DR045SS* M4.5 - 22 - 8 - - 100
DR06 M6 - 22 - 10 - - 100
DR06SS* M6 - 22 - 10 - - 100
*Denotes Stainless Steel Grade AISI 316 (A4)

Loxin™
Shield Anchors
Internally threaded anchor places

no restrictions on fixture thickness
Medium Duty Anchors
Four-way expansion provides

better grip in weaker substrates
Captive threaded nut for use with

machine bolts and threaded rod
Description
The Loxin™ Shield Anchor is a medium duty, torque controlled, internally
threaded, expansion anchor, designed for use in solid substrates such as
concrete, brick, block and stone. The Loxin™ requires the installation of a
machine bolt or threaded rod to set.
Specification
Material Carbon Steel
Head Style -
Fixing Method Fixture Aligned
Thread Sizes M6, M8, M10, M12, M16 Features & Benefits
Drilled Hole Diameters 13mm, 16mm, 22mm, 26mm • The Loxin™ fits flush with the surface of the substrate, leaving no
Anchor Lengths 35mm, 52mm, 65mm, 75mm protrusions when not in use.
Maximum Fixture Thickness’ - • The anchor’s internal thread facilitates the use of machine bolts and
Indicative Working Max Tensile 2.2kN -10.1kN threaded studs of any length removing restrictions on fixture thickness.
Loads in 32MPa Concrete* Max Shear 1.3kN -10.2kN • The Loxin™ requires only shallow embedment, which reduces the risk of
Substrates Stone, Concrete, Solid Brick, Solid Block striking rebar during hole drilling.
* Refer to load table • Four-way expansion provides better grip in weaker substrates.
Related Products
DynaDrill™ Hole Cleaning Brush
Carbide Drill Bits Hole Cleaning Pump
Diamond Motor Wet and Dry Vacuum

Loxin™
Shield Anchors

Electrical Contractor Mechanical Services Contractor Racking Installer
Electrical Service Suspension 4
Mechanical Service Suspension 4
Pallet Racking 4
Medium Duty Anchors

Installation
1. Drill or core a hole to the recommended diameter and depth. Clean the
hole thoroughly with a hole cleaning brush. Remove the debris with a hand
pump, compressed air, or vacuum.
2. Insert the Loxin™ into the hole, nut end first, and tap with a hammer
until it sits flush with the surface of the substrate.
3. Position the fixture over the Loxin™, insert the correct diameter bolt or
stud through the fixture and tighten.
Loxin™ Shield Anchors - Zinc Plated

RLM06 M6 - 35 13 - 40 40 50
RLM08 M8 - 52 16 - 60 55 25
RLM10 M10 - 52 16 - 60 55 25
RLM12 M12 - 65 22 - 70 70 25
RLM16 M16 - 75 26 - 80 75 25

DynaSet™
Drop-In Anchors
Internally threaded
anchor places
no restrictions on
fixture thickness
Medium Duty Anchors
Displacement setting allows the

anchor to remain in place without
insertion of machine bolt or
threaded rod
Shallow embedment reduces risk of

striking rebar during hole drilling
Description
The DynaSet™ Drop-In Anchor is an all steel, medium duty, displacement
setting, expansion anchor designed to provide a permanent anchorage point
in concrete. Its internal thread allows it to be used with both machine bolts
and threaded rod, placing no restrictions on fixture thickness. The DynaSet™
requires the use of the correct setting tool to ensure full expansion of the
anchor body. The setting tool also acts as visual check for correct setting of
the anchor.
Specification
Material Carbon Steel, Stainless Steel 316 (A4)
Head Style -
Setting Method Displacement
Anchoring Method Expansion Features & Benefits
Thread Sizes M6, M8, M10, M12, M16, M20 • The Dyna Set™ fits flush with, or just below, the surface of the substrate,
Drilled Hole Diameters 8mm, 10mm, 12mm, 15mm, 16mm, 20mm, 25mm leaving no protrusions when not in use and allowing for easy patch work.
Anchor Lengths 25mm, 30mm, 40mm, 50mm, 60mm, • The anchor’s internal thread facilitates the use of machine bolts and
65mm, 80mm threaded studs of any length, removing restrictions on fixture thickness.
Maximum Fixture Thickness’ - • The DynaSet™ requires only shallow embedment, which reduces the risk
Indicative Working Max Tensile 2.5kN -15.8kN of drilling into rebar.
Loads in 32MPa Concrete* Max Shear 2.2kN - 13.1kN • The setting tool provides a visual expansion check for correct setting of the
Substrates Concrete anchor.
* Refer to load table • The flanged version (zinc plated only) has a retaining lip to keep the
anchor flush with the surface of the substrate. This also allows for
Related Products consistent threaded rod drop lengths.
Diamond Motor DynaSet™ Setting Tool
Diamond Core Drill Bits Safety Ring Anchor
Hole Cleaning Brush

DynaSet™
Drop-In Anchors

Electrical Contractor Mechanical Services Contractor Ceiling & Partitioning Contractor
Electrical Service Suspension 4
Mechanical Service Suspension 4
Ceiling Suspension 4
Installation
1. Drill or core a hole to the recommended diameter and depth. Clean the
Medium Duty Anchors

hole thoroughly with a hole cleaning brush. Remove the debris with a hand
2. Insert the anchor into the hole. Using a hammer and the appropriate
setting tool, drive the expansion plug into the anchor until the shoulder of
the tool rests against the surface of the anchor.
3. Position the fixture, insert the bolt or threaded rod and tighten with a
spanner.
DynaSet™ Drop-in Anchors - Zinc Plated - Standard

Part No Thread Thread Overall Anchor Drilled Hole Min Hole Setting Order
Size Length (mm) Length (mm) Ø (mm) Depth (mm) Tool Qty
DSM06 M6 11 25 8 28 SETDS1 100
DSM08 M8 13 30 10 33 SETDS2 100
DSM10 M10 16 40 12 43 SETDS3 50
DSM12 M12 21 50 16 53 SETDS4 50
DSM16 M16 28 65 20 68 SETDS5 25
DSM20 M20 35 80 25 83 SETDS6 25
DynaSet™ Drop-in Anchors - Zinc Plated - Flanged

DSF06 M6 11 25 8 28 SETDS1 100
RAP06* M6 11 25 8 28 SETDS1 500
DSF10 M10 14 30 12 33 SETDF3 100
RAP01* M10 14 30 12 43 SETDF3 500
DSF12 M12 21 50 16 53 SETDS4 50
RAP012* M12 21 50 16 53 SETDS4 200
* Rod Anchoring Pack (RAP) includes setting tool in a handy carry bucket
DynaSet™ Drop-in Anchors - Stainless Steel AISI 316(A4)

DSM06SS M6 11 25 8 28 SETDS1 100
DSM08SS M8 13 30 10 33 SETDS2 100
DSM10SS M10 16 40 12 43 SETDS3 50
DSM12SS M12 21 50 15 53 SETDS4*/SETDSA4 50
DSM16SS M16 28 60 20 68 SETDS5 25
* Not to be used with DSM12SS when installing Safety Ring Anchor

DynaSet™
Drop-In Anchors
DynaSet™ Drop-in Anchors - Indicative Working Loads in 32MPa Concrete

M6 23 6 80 60 2.5 2.2
M8 28 10 100 70 3.5 2.9
M10 38 20 135 95 5.4 3.5
M10 Flanged 28 12 100 70 3.4 2.9
M12 48 40 170 120 7.7 6.6
M16 63 95 220 160 11.5 10.4
Medium Duty Anchors
M20 78 180 275 195 15.8 13.1

DynaSet™ Setting Tools

Part No Description Suits Order Qty
SETDS1 M6 x 25 Setting Tool DSM06/DSF06 / DSM06SS 1
SETDS2 M8 x 30 Setting Tool DSM08 / DSM08SS 1
SETDF3 M10 x 30 Setting Tool DSF10 1
SETDS4* M12 x 50 Setting Tool DSM12 / DSF12 / DSM12SS 1
SETDSA4 M12 x 50 Setting Tool DSM12SS 1
SETDS6 M20 x 80 Setting Tool DSM20 1
* Not to be used with DSM12SS when installing Safety Ring Anchor
Safety Ring Anchor System

Part No Thread Internal Ring Overall For use Setting Order
Size Diameter (mm) Length (mm) only with Tool Qty
RSR12GM(Gal) M12 16 138 DSM12SS SETSA4 4
RSR12SS(AISI 316[A4]) M12 16 138 DSM12SS SETSA4 4
Note: When installed in accordance with Ramset™ specifications, anchor performance is fully compliant with AS/NZS1891.4:2000 “Industrial fall-arrest systems and devices”.
Installation
1. Drill or core a Ø 15mm hole to depth of
130mm± 2.5mm. Clean the hole
thorougly with a hole cleaning brush.
Remove the debris with a hand
2. Check depth is correct, using the reverse
end of the setting tool (SETSA4). The
depth indicator groove MUST be level
with the concrete surface.
3. Insert the DSM12SS into the hole
by knocking it in, using the reverse end
of the setting tool.
4. Using a hammer and the setting tool, drive
the expansion plug into the anchor until the depth indication groove is level with the concrete surface. If this cannot be achieved, an alternative anchor
point location must be selected.
5. Insert safety ring anchor and rubber seal. Tighten with a bar to the following Tightening Specification:
a. Using a bar not more than 100mm long (the bar should not bend during installation).
b. Using a 150mm long bar, not more than 10mm in diameter and of yield strength not exceeding 300MPa. R10 reinforcement bar is suitable for this purpose.
When the bar starts to bend, the anchor ring should be returned back to the closest vertical orientation. Ensure the anchor ring is left in a vertical position.
The Dynaset™ will remain in position if the safety ring anchor is removed.

Light Duty
Anchors
Light Duty Anchors

RamPlug™
Nylon Frame Anchors
Countersunk sleeve
allows flush finish
Light Duty Anchors
Anti-rotation barbs prevent

anchor from rotating in hole
Nylon sleeve reduces the

effects of cold bridging,
therefore mold growth, when
compared with all-metal fixings
Pictured - Hex Head Ultra Long Plug
Description
The RamPlug™ Nylon Frame Anchor is a light duty, rotation setting,
interference fit anchor, designed for use in a variety of substrates such as
concrete, stone, solid brick, hollow brick, solid block, hollow block, hollow
slab block and lightweight concrete (AAC) block. Available in Standard, Long
and Ultra Long, with (Ultra Long only) or without a countersunk or hex head
screw, there is a RamPlug™ for a range of light duty anchoring applications.
Specification
Material - Sleeve Nylon
Material - Screw Carbon Steel
(Ultra Long only)
(Ultra Long only)
Head Style Countersunk, Hex
(Ultra Long only) Features & Benefits
Fixing Method Through Fixture (Long, Ultra Long) • Anti-rotation barbs prevent the anchor from rotating in the hole
Fixture Aligned (Standard) • Countersunk sleeve allows for flush finishing.
Setting Method Rotation • Nylon sleeve reduces the effects of cold bridging, e.g. mold growth,
Anchoring Method Interference Fit when compared to all-metal anchors.
Screw Gauge 5 - 24
Drilled Hole Diameters 5mm, 6mm, 7mm, 8mm, 10mm, 12mm
Anchor Lengths 25mm, 30mm, 40mm, 50mm, 60mm,
80mm, 100mm, 135mm, 160mm
Maximum Fixture Thickness’ 10mm, 45mm, 70mm
(Ultra Long and Long only) Related Products
Substrates Concrete, Stone, Solid Brick, Hollow Brick, DynaDrill™ / Hammer Drill Driver Impact Driver
Solid Block, Hollow Block, Hollow Slab, Carbide Drill Bits Hex Sockets
Lightweight Concrete (AAC) Block Hole Cleaning Brush Drill Driver
Hole Cleaning Pump Screw Gun
Wet and Dry Vacuum Screwdriver Bits

RamPlug™
Nylon Frame Anchors

Carpenter Flooring Contractor Garage Door Installer Window/Door Installer
Anchoring Wall/Base Plates & Battens 4 4
Fitting Door & Window Frames 4 4
Fitting Garage Doors 4
Installation (Long & Ultra Long Plugs)

1. Drill a hole to the recommended diameter and depth using the fixture as
Light Duty Anchors

a template. If the fixture thickness is less than the maximum, increase the
hole depth accordingly. Clean the hole thoroughly with a hole cleaning
2. Insert the anchor through the fixture and tap with a hammer until the collar
of the anchor contacts the fixture.
3. Tighten screw until the head of the screw is flush with the collar of the
anchor.
RamPlug™ Anchors - Standard*

Part No Anchor Max Fixture Overall Anchor Drilled Hole Min Hole Screw Order
Size (mm) Thickness (mm) Length (mm) (mm) Depth (mm) Gauge Qty
DNP05 5 - 25 5 30 5 - 7 100
DNP06 6 - 30 6 40 6 - 9 100
DNP07 7 - 30 7 40 9 - 12 100
DNP08 8 - 40 8 50 10 - 14 100
DNP10 10 - 50 10 60 14 - 18 50
DNP12 12 - 60 12 75 18 - 24 25
* Screw not supplied

RamPlug™ Anchors - Long Plug*

Part No Anchor Max Fixture Overall Anchor Drilled Hole Min Hole Screw Order
Size (mm) Thickness (mm) Length (mm) (mm) Depth (mm) Gauge Qty
DLP08 8 10 80 8 90 10 - 14 100
DLP10 10 10 80 10 90 14 - 18 50
* Screw not supplied
Countersunk
RamPlug™ Anchors - Ultra Long Plug*

Part No Anchor Max Fixture Overall Anchor Drilled Hole Min Hole Head Order
Size (mm) Thickness (mm) Length (mm) (mm) Depth (mm) Style Qty
DUP10080F 10 10 80 10 90 Countersunk 25
DUP10080H 10 10 80 10 90 Hex 25
DUP10100H 10 10 100 10 110 Hex 25
DUP10135H 10 45 135 10 145 Hex 25
DUP10160H 10 70 160 10 170 Hex 25
* Supplied complete with screws

EasyDrive™
Nylon Drive Anchors
Light Duty Anchors
Wide, flat collar with collapsable

sleeve design ensures tight fixing
Saw tooth thread makes Innovative design ensures the

driving and unscrewing easier anchor can be hammered all the
way in without pre-expansion
Description
The EasyDrive™ Nylon Drive Anchor is a removable light duty, impact/
rotation setting, interference fit anchor, designed for use in a variety of
substrates such as concrete, stone, solid brick, solid block, hollow brick,
hollow block and hollow slab.
Specification
Material - Drive Screw Carbon Steel, Stainless Steel 316 (A4)
Head Style - Drive Screw Countersunk
Setting Method Impact/Rotation
Anchoring Method Interference Fit Features & Benefits
Drilled Hole Diameters 5mm, 6mm, 8mm • The innovative design of the EasyDrive™ ensures that it can be
Anchor Lengths 33mm, 42mm, 50mm, 55mm, 70mm, hammered all the way into the hole without pre-expansion.
75mm, 120mm • The drive screw’s saw tooth thread makes it easy to drive and unscrew.
Maximum Fixture Thickness’ 6mm,12mm, 25mm, 30mm, 40mm, 75mm • A wide, flat collar with collapsable sleeve design, ensures tight fixing.
Substrates Concrete, Stone, Solid Brick, Solid Block, • Nylon body provides insulation between drive screw and work surface.
Hollow Block, Hollow Slab, Hollow Brick
Related Products
DynaDrill™ / Hammer Drill Driver Drill Driver
Carbide Drill Bits Screw Gun
Hole Cleaning Brush Screwdriver Bits
Hole Cleaning Pump
Wet and Dry Vacuum

EasyDrive™
Nylon Drive Anchors

Electrical Contractor Bricklayer Plumbing Contractor
Electrical Fitting Installation 4
Brick Tie Installation 4
Pipe/Conduit Saddle Installation 4 4
Light Duty Anchors

Installation
hole depth accordingly. Remove the debris with a hand pump, compressed
air, or vacuum.
2. Insert the anchor through the fixture until the collar of the anchor contacts
the fixture.
3. Screw or tap home the drive screw with a hammer until the head is flush
with the collar of the anchor. The drive screw can easily be removed with a
screwdriver.
EasyDrive™ Nylon Anchors - Zinc Plated Drive Screw

Part No Anchor Max Fixture Overall Anchor Drilled Hole Min Hole Order
Size (mm) Thickness (mm) Length (mm) Ø (mm) Depth (mm) Qty
ED05033 5 6 33 5 40 100
ED05050 5 20 50 5 45 100
ED06042 6 12 42 6 50 100
ED06055 6 25 55 6 50 100
ED06075 6 40 70 6 50 100
ED08080 8 30 75 8 80 50
ED08120 8 75 120 8 95 50
EasyDrive™ Nylon Anchors - Stainless Steel AISI 316 (A4) Drive Screw
Part No Anchor Max Fixture Overall Anchor Drilled Hole Min Hole Order
Size (mm) Thickness (mm) Length (mm) Ø (mm) Depth (mm) Qty
ED05033SS 5 6 33 5 40 100
ED06042SS 6 12 42 6 50 100
ED06055SS 6 25 55 6 50 100
ED06075SS 6 40 70 6 50 100

Nylon Anchors
Multiple head styles for versatility

Light Duty Anchors
Saw tooth thread makes

driving and unscrewing easier
Requires only a small

hole for discreet fixing
Description
The Ramset™ Nylon Anchor is a removable light duty, impact/
rotation setting, interference fit anchor, with a variety of head styles, designed
for use in a variety of substrates such as concrete, stone, solid brick, solid
block, grout filled block and hollow block.
Specification
Material - Drive Screw Carbon Steel, Stainless Steel 316 (A4)
Head Style - Anchor Mushroom, Round, Countersunk, Flat
Setting Method Impact/Rotation
Anchoring Method Interference Fit Features & Benefits
Drilled Hole Diameters 5mm, 6.5mm • Available in multiple head styles for versatility.
Anchor Lengths 20mm, 25mm, 38mm, 50mm, 75mm • The drive screw’s saw tooth thread makes it easy to drive and unscrew.
Maximum Fixture Thickness’ 2mm, 5mm,13mm, 25mm, 50mm • Requires only small diameter holes for discreet fixing.
Substrates Concrete, Stone, Solid Brick, Solid Block • Nylon body provides insulation between drive screw and work surface.
Related Products
Hole Cleaning Pump Screwdriver Bits
Wet and Dry Vacuum

Nylon Anchors

Electrical Contractor Signwriter Plumbing Contractor
Sign Installation 4
Installation
Light Duty Anchors

hole depth accordingly. Remove the debris with a hand pump, compressed
air, or vacuum.
2. Insert the anchor through the fixture until the collar of the anchor contacts
the fixture.
3. Screw or hammer home the drive screw until the head is flush with the
collar of the anchor. The drive screw can easily be removed with a
screwdriver.
Nylon Anchor - Mushroom Head

Part No Anchor Anchor Drilled Hole Hole Max Fixture Order
Size (mm) Length (mm) Ø (mm) Depth (mm) Thickness (mm) Qty
TNM320 5 20 5 25 2 100
TNM325# 5 25 5 30 5 100
TNM425# 6.5 25 6.5 30 5 100
TNM438 6.5 38 6.5 40 13 100
TNM450 6.5 50 6.5 45 25 100
TNM475 6.5 75 6.5 55 50 50
# Available with stainless steel expansion nail. Add SS to end of Part No.
Nylon Anchor - Round Head

TNR325# 5 25 5 30 5 100
TNR338 5 38 5 40 13 100
TNR425 6.5 25 6.5 30 5 100
TNR438 6.5 38 6.5 40 13 100
TNR450 6.5 50 6.5 45 25 100
# Available with stainless steel expansion nail. Add SS to end of Part No.
Nylon Anchor - Countersunk Head

TNF425 6.5 25 6.5 30 5 100
TNF438 6.5 38 6.5 40 13 100
TNF450 6.5 50 6.5 45 25 100
TNF475 6.5 75 6.5 55 50 50
Nylon Anchor - Flat Head

TNL325 5 25 5 30 5 100

ShureDrive™
Drive Anchors
Full expansion is evident when

the head of the expansion nail
sits flush with the flange
Light Duty Anchors
Large flange to prevent pull out
Tamper resistant head
Description
The ShureDrive™ Drive Anchor is an all metal light duty, impact setting,
interference fit anchor, designed for tamper resistant use in a variety of
substrates such as concrete, stone, solid brick, solid block, hollow brick,
hollow block and hollow slab.
Specification
Material Zinc Alloy Body, Carbon Steel Nail
Head Style - Anchor Mushroom
Setting Method Impact
Anchoring Method Interference Fit
Drilled Hole Diameters 5mm, 6mm Features & Benefits
Anchor Lengths 22mm, 30mm, 50mm • Hammer-in method makes installation quick and easy.
Maximum Fixture Thickness’ 3mm, 5mm, 25mm • Full expansion of the anchor is evident when the head of the expansion
Substrates Concrete, Stone, Solid Brick, Solid Block, nail sits flush with the flange.
Grout Filled Block, Hollow Brick, Hollow Block, • Once fully set, the ShureDrive™ becomes tamper resistant.
Hollow Slab • The anchor’s large flange prevents pullout.
Note: The ShureDrive™ Drive Anchor should not be used for top fix or
overhead appications
Related Products
DynaDrill™ / Hammer Drill Driver
Carbide Drill Bits
Hole Cleaning Pump
Wet and Dry Vacuum

ShureDrive™
Drive Anchors

Electrical Contractor Signwriter Plumbing Contractor Bricklayer
Brick Tie Installation 4
Sign Installation 4
Light Duty Anchors

Installation
1. Drill a hole to the recommended diameter and depth using the fixture as a
template. Remove the debris with a hand pump, compressed air, or
vacuum.
2. Insert the anchor through the fixture until the flange of the anchor contacts
the fixture.
3. Hammer home the expansion nail until the head is flush with the flange of
the anchor.
ShureDrive™ Anchors
Part No Anchor Max Fixture Overall Anchor Head Drilled Fixture Hole Min Hole Order
Size Thickness Length Ø Hole Ø Ø Depth Qty
(mm) (mm) (mm) (mm) (mm) (mm) (mm)
SDM05022 5 3 22 11 5 6 30 100
SDM06030 6 5 30 13 6 7 35 100
SDM06030SS 6 5 30 13 6 7 35 100
SDM06050 6 25 50 13 6 7 55 100

RediDrive™
Hammer-In Anchors
Light Duty Anchors
100% hole contact provides

maximum holding power
Tamper resistant and flush
finishing mushroom head
Dog point for

easy insertion
and installation
Description
The RediDrive™ Hammer-In Anchor is a one-piece, all steel, light duty,
impact setting, interference fit anchor designed for use in concrete. The
RediDrive™ is simply hammered through the fixture into a pre-drilled hole.
Its tamper resistant mushroom head sits flush and its interference fit is
permanent.
Specification
Corrosion Protection Mechanical Zinc Plating
Head Style - Anchor Mushroom
Drilled Hole Diameters 5mm Features & Benefits
Anchor Lengths 30mm, 40mm, 50mm, 65mm, 75mm • The RediDrive™ features a dog point for easy insertion and installation.
Maximum Fixture Thickness’ 5mm, 15mm, 20mm, 35mm, 45mm • Hammer-in method makes installation quick and easy.
Substrates Concrete • The anchor makes 100% contact with the wall of the pre-drilled hole
providing a perfect interference fit and maximum holding power.
• The anchor’s mushroom head provides a tamper resistant flush finish.
Related Products
Carbide Drill Bits
Hole Cleaning Pump
Wet and Dry Vacuum

RediDrive™
Hammer-In Anchors

Carpenter Signwriter Plumbing Contractor Electrical Contractor
Timber Batten/Window Frame Installation 4
Sign Installation 4
Fire collar retrofit 4
Light Duty Anchors

Installation
1. Drill a 5mm hole to the recommended depth using the fixture as a
template.
2. Remove the debris with a hand pump, compressed air, or vacuum.
3. Insert the dog point through the fixture and drive the anchor with a mash
hammer until the head is flush with the fixture.
RediDrive™ Hammer-In Anchors

Part No Anchor Max Fixture Overall Anchor Drilled Fixture Hole Min Hole Order
Size Thickness Length Hole Ø Ø Depth Qty
(mm) (mm) (mm) (mm) (mm) (mm)
RD05030 5 5 30 5 6.5 40 100
RD05040 5 15 40 5 6.5 47 100
RD05050 5 20 50 5 6.5 47 100
RD05065 5 35 65 5 6.5 57 100
RD05075 5 45 75 5 6.5 52 100

Concrete Nails
Pre-assembled washer
improves pullover strength
Light Duty Anchors
(CW - Washered range only)
Hammers straight into

High strength and medium strength concrete
ductile material
Description
Ramset™ concrete nails are manufactured from ductile, high strength
carbon steel and are available in a number of different styles to suit a range
of applications. They are designed for hand hammer driving into medium
strength concrete and solid block.
Caution
Always wear eye protection when setting concrete nails.
Always strike the nail head squarely with the hammer face.
Specification
Corrosion Protection Zinc Plating, Mechanical Galvanising
Head Style Flat, Countersunk, Bullet
Fixing Method Through fixture
Setting Method Impact Features & Benefits
Anchoring Method Interference fit • Manufactured from ductile, high strength material to avoid breakage.
Shank Diameters 2.4mm, 3.2mm, 3.6mm, 3.8mm, 4.0mm, • Available with pre-assembled washers to improve pullover strength.
4.2mm • Available with either a plain or striated shank and in a range of different
Anchor Lengths 15mm, 20mm, 25mm, 30mm, 38mm, sizes and head styles.
40mm, 50mm, 60mm, 63mm, 75mm,
100mm
Maximum Fixture Thickness’ up to 75mm
Substrates Concrete, Solid Block

Concrete Nails

Carpenter Signwriter Plumbing Electrical Concrete
Contractor Contractor Formworker
Timber Batten Installation 4
Sign Installation 4
Formwork support 4
Light Duty Anchors

Installation
1. Hammer the concrete nail through the fixture into the concrete until the
nail head is flush with the fixture.
CK - Striated CF - Plain Shank CD- Plain Shank
Concrete Nails
Part No Description Shank Ø (mm) Overall Length (mm) Order Qty
CD425 Plain 2.4 25 100
CD430 Plain 2.4 30 100
CD440 Plain 2.4 40 100
CD525 Plain 3.2 25 100
CD540 Plain 3.2 40 100
CF650 Plain 3.8 50 100
CF660 Plain 3.8 60 100
CF675 Plain 3.8 75 100
CW415 Washered 2.4 15 100
CW415Q500 Washered 2.4 15 500
CW420Q500 Washered 2.4 20 500
CW425Q500 Washered 2.4 25 500
CW430Q500 Washered 2.4 30 500
CK540 Striated 3.2 38 100

Plastic Plugs
& Spaghetti
Light Duty Anchors
Neat and convenient frame pack

Colour coded to indicate plug size
Description
Ramset™ plastic plugs and spaghetti are inexpensive, traditional expansion
plugs for light duty anchoriong in concrete, stone, solid brick and solid block.
Both may be used with screws. Spaghetti may also be used with nails.
Specification
Material Plastic
Setting Method Rotation/Impact
Screw Gauges 4.5-6, 8-9, 10-12, 14-16
Drilled Hole Diameters 5mm, 5.5mm (Spaghetti), 6mm, 7mm, 8mm
Plug Lengths 25mm, 32mm, 38mm, 50mm Features & Benefits
Spaghetti Roll Lengths 5m, 50m • Ramset™ plastic plugs are tapered at one end for quick and easy
Roll Plug Lengths 100m insertion.
Maximum Fixture Thickness’ - • Ramset™ plastic plugs are available in a neat and convenient frame pack
Substrates Concrete, Stone, Solid Brick, Solid Block or economical 100m roll.
• Ramset™ cut-to-length spaghetti is available in either 5m or 50m rolls
and may be used with either screws or nails.
Related Products
Hole Cleaning Pump Screwdriver Bits
Wet and Dry Vacuum

Plastic Plugs
& Spaghetti

Miscellaneous Trades Signwriter Plumbing Contractor Electrical Contractor
Light Hook/Bracket Installation 4
Sign Installation 4
Light Duty Anchors

Installation
1. Drill a hole to the appropriate diameter and depth. Remove the debris with a hand pump, compressed air, or vacuum.
2. Insert the plug/spaghetti into the hole.
3. Screw the screw through the fixture into the plug/spaghetti until fixture is fi rm against the substrate.
Plastic Plugs (Frame Packs)

Part No Colour Drilled Hole Plug Screw Order
Ø (mm) Length (mm) Guage Qty
WPWH25 White 5 25 4.5 - 6 1,000
WPRD25 Red 6 25 8 - 9 1,000
WPRD32 Red 6 30 8 - 9 1,000
WPRD38 Red 6 35 8 - 9 1,000
WPRD50 Red 6 50 8 - 9 1,000
WPGR25 Green 7 25 10 - 12 1,000
WPGR32 Green 7 30 10 - 12 1,000
WPGR38 Green 7 35 10 - 12 500
WPGR50 Green 7 50 10 - 12 500
WPBU38 Blue 8 35 14 - 16 500
WPBU50 Blue 8 50 14 - 16 500
Plastic Plugs (Roll)

Ø (mm) Length (metres) Guage Qty
720115 Red 6 100 8 - 9 1
720122 Green 7 100 10 - 12 1
720139 Blue 8 100 14 - 16 1
Plastic Spaghetti
Ø (mm) Length (metres) Guage Qty
463609 Orange 5 5 4.5 - 6 1
RSP Orange 5 50 4.5 - 6 1

Notes
Notes

Specialised
Anchors
Specialised Anchors

AnkaScrew™
Fire Rated Suspension Anchors
Patented Sinuloc® Wave Thread

prevents accidental unscrewing or
movement due to vibration (Stud only)
Specialised Anchors
Low thread pitch

resists cyclic loading
Wide thread angle

increases the mechanical
interlock with the substrate
Patented “shark’s tooth” thread

reduces installation torque
Description
Designed specifically for overhead threaded rod applications, AnkaScrew™
Rod provides a faster screw-in anchoring solution than traditional drop-in
anchors. AnkaScrew™ Rod is suitable for suspension of sprinkler pipe
systems, metal and plastic pipes, steel ductwork, steel trays, steel channel
and steel trapeze and can be used for overhead, horizontal and vertical appli-
cations. AnkaScrew™ Stud is ideal for fast, direct to surface mounting of steel
pipe clamps, metal brackets, steel trays and sprinkler clamps. AnkaScrew™
Stud provides users with the same features and benefits as AnkaScrew™
Rod. Both anchors are well suited to close-to-edge or close-to-anchor fixing
as they do not expand and risk bursting the surrounding substrate.
Specification
Material High Carbon Steel
Corrosion Protection Mechanical Galvanising
Head Style M10 Internally Threaded 13mm Hex Head Features & Benefits
(AnkaScrew™ Rod), • Fire Rated to and complies with AS1530.4
M8 Externally Threaded Stud with 10mm • The patented “shark’s tooth” thread reduces installation torque, while the
Hex (AnkaScrew™ Stud) wide thread angle and low thread pitch increases the mechanical interlock
Fixing Method Fixture Aligned with the substrate and resists cyclic loading.
Setting Method Rotation • Both AnkaScrew™ Rod and Stud are fast and easy to install as they simply
Anchoring Method Thread Forming screw into a small (6mm) pre-drilled hole, using an impact driver, reducing
Drilled Hole Diameters 6mm the risk of incorrect setting, as well as the dust, noise and fatigue
Anchor Lengths 35mm associated with traditional overhead anchoring methods that require larger
Substrates Concrete, Solid Brick, Solid Block, (10mm and 12mm ) holes and manual setting.
Hollow Brick, Hollow Block, Hollow Slab • Short body length minimises re-bar strikes, increasing carbide life.
• Both AnkaScrew™ Rod and Stud are easily removed leaving an empty hole
Related Products with no protruding metal parts to grind off.
• Ideal for close-to-edge and close-to-anchor installation. Self-tapping,
DynaDrill™ / Hammer Drill Driver Impact Wrench rotation setting method of installation is not subject to any expansion
Carbide Drill Bits Long Impact Sockets (10mm pressure, therefore does not risk bursting the substrate.
Hole Cleaning Pump Stud/13mm Rod)
Wet and Dry Vacuum

AnkaScrew™
Fire Rated Suspension Anchors

Plumbing Contractor Electrical Contractor Mechanical Services Contractor
Pipe Suspension ✔ 4 4
Cable & Cable Tray Suspension 4 4 ✔
Duct Suspension 4
Specialised Anchors
Installation
1. Drill a 6mm diameter x 45mm (min) deep hole in the desired position.
Remove the debris with a hand pump, compressed air, or vacuum.
2. Insert the AnkaScrew™ Rod or Stud and screw it into the hole with
either a socket wrench or an impact wrench using slight pressure until the
self-tapping action begins.
3. Tighten the AnkaScrew™ Rod or Stud until firm. If resistance is
experienced when tightening, unscrew the anchor one turn and
re-tighten. Ensure that you do not over tighten.
AnkaScrew™ Stud AnkaScrew™ Rod
AnkaScrew™ Suspension Anchors - Mechanically Galvanised

Part No Description Anchor Anchor Drilled Hole Min Hole Order
Size Length Ø Depth Qty
(mm) (mm) (mm) (mm)
AS06035R AnkaScrew™ Rod - M10 Thread 6 35 6 45 50
AS06035S AnkaScrew™ Stud - M8 Thread 6 35 6 45 100
AnkaScrew™ Suspension Anchors - Indicative Working Loads in 32MPa Concrete

Anchor Size/ Embedment Min Edge Min Anchor Working Load Limit
Hole Ø (mm) Depth (mm) Distance (mm) Spacing (mm) (Tension)*
6 45 25 50 500kg
* This value incorporates a factor of safety FoS = 3 from the tested characteristic load = 1.5t

TruFast™
Push-Pull Suspension Anchor
Tie wire head

Specialised Anchors
Load assisted expansion

sleeve with gripping lugs
Anchor Diameter Equals Hole Diameter
Description
The TruFast™ Push-Pull Suspension Anchor is an all metal, tie wire, load
assisted expansion anchor designed for fixing suspended ceiling cables to
concrete soffits.
Specification
Head Style Tie Wire
Fixing Method In Place
Setting Method Applied load
Drilled Hole Diameter 6mm Features & Benefits
Anchor Length 55mm, 120mm • The TruFast™ Suspension Anchor’s body diameter equals the hole
Eye Diameter 6.5mm diameter providing maximum shear capacity for hole size. Its cold forged
Substrates Concrete construction ensures superior strength and reliability.
• The anchor design ensures maximum expansion of the sleeve. This
action is further assisted by the application of load - ideal for a suspension
anchor.
• The gripping lugs on the expansion sleeve grip of the sides of the hole to
aid full expansion during setting.
Related Products
Carbide Drill Bits
Hole Cleaning Pump
Wet and Dry Vacuum

TruFast™
Push-Pull Suspension Anchor

Ceiling & Partitioning Contractor
Suspended Ceiling Installation 4
Specialised Anchors
Installation
1. Drill a 6mm diamater hole, to the recommended depth, into the concrete
soffit. Remove the debris with a hand pump, compressed air, or vacuum.
2. Insert the anchor into the hole and tap with a hammer until the anchor can
go no further.
3. Using the claw of a hammer, pull down on the head of the anchor until set.
TruFast™ Push-Pull Suspension Anchors

Part No Anchor Anchor Eye Drilled Hole Min Hole Order
Size Length Ø Ø Depth Qty
(mm) (mm) (mm) (mm) (mm)
TFE06 6 55 6.5 6 45 100
TFE06120 6 120 6.5 6 110 100
Indicative tensile working load in concrete 25MPa or greater is 1.9kN

Catenary Wire Eye
Suspension Anchor
Tie wire head

Specialised Anchors
100% hole contact provides

Dog point for easy
insertion and
installation
Description
The Ramset™ Catenary Wire Eye is a one-piece, all steel, light duty, impact
setting, interference fit suspension anchor designed for use in concrete
soffits. The anchor is simply hammered into a pre-drilled hole where its
100% interference fit is permanent.
Specification
Head Style - Anchor Tie Wire
Anchor Lengths 40mm • The Ramset™ Catenary Wire Suspension Anchor features a dog point for
Eye Diameter 7mm easy insertion and installation.
Substrates Concrete • Hammer-in method makes installation quick and easy.
• The anchor makes 100% contact with the wall of the pre-drilled hole
providing a perfect interference fit and maximum holding power.
Related Products
Carbide Drill Bits
Hole Cleaning Pump
Wet and Dry Vacuum

Catenary Wire Eye
Suspension Anchor

Suspended Ceiling Installation 4
Specialised Anchors
Installation
1. Drill a 5mm hole to 40mm deep.
2. Remove the debris with a hand pump, compressed air, or vacuum.
3. Insert the dog point into the pre-drilled hole and hammer the anchor in.
Catenary Wire Eye

Part No Anchor Anchor Eye Drilled Hole Min Hole Order
Size Length Ø Ø Depth Qty
(mm) (mm) (mm) (mm) (mm)
CWE05040 5 40 7 5 40 100

Vertical Flange Clip
Gripping barbs
Specialised Anchors
Tie wire eye
Purlin hook
Description
The Ramset™ Vertical Flange Clip is a suspension anchor, designed for use
with steel “C” Section purlins.
Specification
Material Pressed Steel
Head Style Purlin Hook
Anchoring Method Gravity/Clamping
Hole Diameters 3mm & 6mm
Anchor Length 42mm
Purlin Guages 1.6mm - 2.5mm
Substrates Steel “C” Section Purlins
Features & Benefits Installation

• The Ramset™ Vertical Flange Clip features gripping barbs for a firm hold 1. Place the purlin hook profile over the vertical flange of the “C” purlin.
on the flange of the “C” purlin. 2. Tap into place with a hammer.
• For suspended ceilings, angle trim may be bolted through the larger hole 3. Connect drop wire or chains through the “eye” of the clip.
using M6 bolts.

Electrical Contractor Ceiling & Partitioning Contractor
Fixing Electrical Cable to Steel Purlins 4
Fixing Lighting Systems to Steel Profiles 4
Fixing Suspended Ceilings to Steel Profiles 4
Vertical Flange Clip

Part No Description Flange Small Order
Thickness (mm) Hole Ø (mm) Qty
VF1 For Flanges 1.6 - 2.5mm 7 3 100

DynaClip™
Spring Steel Clip
Purlin hook
Specialised Anchors
Cable/Conduit Clip
Description
The DynaClip™ is a spring steel clip system for quick, simple attachment of
cables and conduit to steel profiles.
Specification
Material Spring Steel
Head Style Purlin Hook
Anchoring Method Clamping
Cable/Conduit Diameters 6mm-10mm, 16mm-20mm, 25mm-32mm
Anchor Lengths 43mm, 57mm
Purlin Guages 2mm-10mm
Substrates Steel Profiles

• The DynaClip™ Spring Steel Clip is quick and easy to attach to steel 1. Place the hook profile over the horizontal of the steel profile.
profiles. 2. Tap into place with a hammer.
• The DynaClip™ is all steel and therefore fire resistant.
• Available for a range of cable/conduit diameters.

Electrical Contractor Ceiling & Partitioning Contractor
Fixing Electrical Cable to Steel Purlins 4
Fixing Lighting Systems to Steel Profiles 4
Fixing Suspended Ceilings to Steel Profiles 4
DynaClip™
Part No Description Flange Order
Thickness Qty
DK20 For Cables 16 - 20mm 2.0 - 10.0 100
DK32 For Cables 25 - 32mm 2.0 - 10.0 100

InsulFast™
Drill Anchor
Large 90mm diameter head

for secure fixing of a variety
of insulation materials
Specialised Anchors
Gripping barbs
Description
The InsulFast™ Drill Anchor is a light duty, impact set, interference fit anchor,
designed for fixing the majority of insulation materials to solid substrates
such as concrete, brick, block and stone.
Specification
Material Polypropylene
Temperature Range -30°C to + 80°C
Head Style Disc
Anchor Lengths 95mm, 115mm, 135mm • The InsulFast™ Drill Anchor is quick and easy to install through
Min/Max Insulation 50/60mm, 70/80mm, insulation.
Thickness’- 90/100mm • Although best suited to rigid insulation, such as extruded polystyrene, the
Indicative Tensile Loads Concrete - 10kg anchor’s large 90mm diameter head allows secure fixing of a variety of
Solid Brick - 8kg insulation materials.
Stone/Solid Block - 6kg • Made of polypropylene, the InsulFast™ Drill Anchor is suited to a wide
Substrates Stone, Concrete, Solid Brick, Solid Block temperature range of between -30°C to + 80°C
Related Products
Carbide Drill Bits

InsulFast™
Drill Anchor

Insulation Contractor
Insulation Fixing 4
Compatible Insulation Types
Specialised Anchors
Extruded Polystyrene Fibreglass / Rockwool Expanded Polystyrene
(Compatibility dependent on ability
to drill through insulation)
Installation
1. Drill an 8mm hole through the insulation and a further 45mm into the
substrate.
2. Insert the anchor through the insulation and into the pre-drilled hole.
3. Using light hammer blows, drive the anchor into the hole until the head of
the anchor is in contact with the insulation and the insulation is firmly held
against the substrate.
InsulFast™ Drill Anchor

Part No Min./Max. Overall Anchor Drilled Hole Min Hole Order
Insulation Thickness Length Ø Depth Qty
(mm) (mm) (mm) (mm)
CB5060 50/60 95 8 45 200
CB7080 70/80 115 8 45 200
CB90100 90/100 135 8 45 200

Notes
Notes

Plasterboard
& Cavity Anchors
Plasterboard & Cavity Anchors

Hollow Wall
Anchors
Anti-rotation barbs
Low profile head

& large flange
Collapsing legs Integral nut
Description
The Ramset™ Hollow Wall Anchor is an all metal, light duty, cavity fixing for
plasterboard and other hollow wall materials up to 38mm.
Specification
Material Pressed Steel Body, Carbon Steel Screw
Head Style Slotted Philips Button Head
Setting Method Setting Tool/Rotation
Anchoring Method Deformation
Thread Diameters M4, M5, M6 Features & Benefits
Drilled Hole Diameters 8mm, 9mm, 13mm • The Hollow Wall Anchor’s low profile head allows for flush finishing.
Wall Thickness’ 0mm-5mm, 6mm-10mm, 6mm-16mm, • The anchor’s large flange prevents the head from pulling into the
8mm-13mm, 16mm-24mm, 34mm-38mm substrate.
Maximum Fixture Thickness’ 10mm, 15mm, 17mm, 20mm, 22mm • Anti-rotation barbs, incorporated in the flange, prevent the anchor from
Substrates Plasterboard, Ply Wood, Cement Sheet spinning in the hole.
• Collapsing legs with an integral nut provide high strength and allow the
screw to be removed without loosing the anchor inside the cavity.
Related Products
Drill Screwdriver Bits
Drill Bits Hollow Wall Anchor Setting Tool
Drill Driver
Screw Gun

Hollow Wall
Anchors

Miscellaneous Trades Plumbing Contractor Electrical Contractor

Installation
1. Drill a hole to the recommended diameter.
(HW10M4P may be hammered into
plasterboard)
2. Tap the anchor into the hole until it is flush
with the surface of the substrate.
3. Attach the setting tool to the head of the
screw. Squeeze the trigger to expand the
anchor. (Small sizes may be set using a
screwdriver)
4. Remove the screw and place it through the
fixture then back into the anchor. Tighten
the screw until the fixture is fixed.
HW10M4P - Pointed
Hollow Wall Anchor

Part No Thread Wall Max Fixture Drilled Hole Order
Size Thickness (mm) Thickness (mm) Ø (mm) Qty
HW05M4 M4 0 - 5 10 8 100
HW10M4 M4 6 - 10 15 8 100
HW10M4P M4 6 - 10 17 8 100
HW13M4 M4 8 - 13 15 8 100
HW24M4 M4 16 - 24 17 8 100
HW38M4 M4 34 - 38 15 8 100
HW14M5 M5 8 - 13 20 9 100
HW16M6 M6 6 - 16 22 13 100
Hollow Wall Anchor - Setting Tool

Part No Description Order Qty
SETHWG Setting Tool 1

WallMate™
Plasterboard Anchors
Flush head
Break away drill point

allows easy installation
and the use of over-long
screws
Screw thread profile designed for

efficient cutting and positive grip
Description
The WallMate™ is the original self drilling plasterboard anchor. Available in
nylon or zinc, the WallMate™ would probably be the quickest and easiest
plasterboard anchor to install and remove.
Specification
Material Nylon, Zinc Composite
Corrosion Protection -
Head Style Flush - Phillips #2
Anchoring Method Thread Forming
Screw Gauges 6-8 Features & Benefits
Drilled Hole Diameters* 8mm • Both versions of the WallMate™ feature an effective drill point for easy
Anchor Lengths 42mm penetration of plasterboard and fast installation. If a long screw is used,
Minimum Screw Length 20mm this point will break away so as not to restrict achievement of a firm fix.
Substrates Plasterboard, Dry Partition Walls, Aerated • The anchor’s screw thread profile is designed for efficient cutting and
Concrete (with 8mm pre-drilled hole) positive grip.
*For pre-drilling into aerated concrete • Both the screw and the WallMate™ can be easily removed without losing
the anchor inside the cavity.
• The low profile head allows for flush fixing.
Related Products
Drill Drill Driver
Hole Cleaning Pump* Screw Gun
Wet and Dry Vacuum* Drill Bits
*For installation in aerated concrete

WallMate™

Bathroom Accessory Installation 4

Installation
1. Insert the point of a #2 Philips Head screwdriver into the recess of the
WallMate™, place the drill point against the wall, lightly piercing the face
paper, and screw the anchor into the plasterboard until the head is flush
with the surface.
2. Place the fixture over the anchor, insert the appropriate gauge screw
through the fixture, into the head of the WallMate™ and tighten the fixture
in place.
WallMate™ - Plasterboard Anchor

Part No Anchor Min Screw Drilled Hole Screw Body Order
Length (mm) Length (mm) Ø* (mm) Gauge Type Qty
WMZ 42 20 8 6-8 Metal 100
WM25 42 20 8 6-8 Nylon 100
* For pre-drilling into aerated concrete

ToggleMate™
Flush head
Screw thread profile designed for

efficient cutting and positive grip
Drill point allows quick

Movable toggle allows and easy installation
fixture to be clamped
tightly against plasterboard
Description
The ToggleMate™ is a self drilling toggle anchor for heavy duty, vibration
resistant fixing in plasterboard.
Specification
Material Zinc Composite
Head Style (Anchor) Flush - Phillips #2
Head Style (Screw) Pan - Phillips #2
Anchoring Method Deformation Features & Benefits
Screw Gauges 8 • The ToggleMate™ features an effective drill point for easy penetration of
Anchor Length 64mm plasterboard and fast installation.
Screw Length 55mm • The anchor’s screw thread profile is designed for efficient cutting and
Substrates Plasterboard positive grip, while the movable toggle allows the anchor to clamp the
plasterboard for added strength.
• Both the screw and the ToggleMate™ can be easily removed without
losing the anchor inside the cavity.
• The low profile head allows for flush fixing.
Related Products
Drill Driver
Screw Gun
Screwdriver Bits

ToggleMate™


Installation
1. Insert the point of a #2 Philips Head screwdriver into the recess of the
ToggleMate™, place the drill point against the wall, lightly piercing the
face paper, and screw the anchor into the plasterboard until the head is
flush with the surface.
2. Place the fixture over the anchor, insert the 8 gauge screw through the
fixture, into the head of the ToggleMate™ and turn to engage the clamp.
Continue to turn the screw until the clamp is pulled tight against the
plasterboard.
ToggleMate™ - Plasterboard Anchor

Part No Anchor Screw Screw Body Order
Length (mm) Length (mm) Gauge Type Qty
TM16 64 55 8 Metal 50

Spring Toggle
Cavity Fastener
Multiple Head Styles for a variety of applications

No protruding flange allows

for ultra flush fixing
Wide wingspan for

Description
Ramset™ Spring Toggles are all metal wing cavity anchors, ideal for both
wall and ceiling applications.
Specification
Head Style Round, Countersunk, Hook
Fixing Method Screw Through Fixing
Screw Gauges 1/8”, 3/16” Features & Benefits
Drilled Hole Diameters 7/16”, 9/16” • Ramset™ Spring Toggles have a wide wingspan to give high loadings in
Anchor Lengths 50mm, 75mm, 100mm both plasterboard wall and ceiling applications.
Maximum Fixture + 15mm, 40mm, 65mm • No protruding flanges allow for ultra flush fixing (Countersunk and
Wall Thickness’ Round head only).
Substrates Plasterboard • Low profile round or countersunk screw heads suit various fixture
recesses. Handy hook profile also available.
Related Products
Drill Screw Gun
Drill Bits Screwdriver Bits
Drill Driver

Spring Toggle
Cavity Fastener


Installation
1. Drill the recommended sized hole through the plasterboard.
2. Pass the screw through the fixture and into the toggle for a few turns.
Compress the toggle wings and insert the anchor into the hole. The wings
will spread behind the cavity wall.
3. Pull back on the fixture to hold the toggle in place against the reverse side
of the cavity wall and tighten with a screwdriver, pulling the wings of the
anchor firm against the cavity wall.
Spring Toggle - Cavity Fastener - Round Head - Zinc Plated

Part No Screw Max Fixture + Wall Screw Drilled Hole Order
Gauge Thickness (mm) Length (mm) Ø (mm) Qty
STR04050 1/8” 15 50 7/16” 100
STR05050 3/16” 15 50 9/16” 100
STR05075 3/16” 40 75 9/16” 50
STR05100 3/16” 65 100 9/16” 50
Spring Toggle - Cavity Fastener - Countersunk Head - Zinc Plated

Part No Screw Max Fixture + Wall Screw Drilled Hole Order
STF05050 3/16” 15 50 9/16” 100
STF05075 3/16” 40 75 9/16” 50
Spring Toggle - Cavity Fastener - Hook - Zinc Plated

Part No Screw Max Wall Screw Drilled Hole Order
STK05050 3/16” 15 50 9/16” 50

RamToggle™
Nylon Cavity Fastener
Wide wingspan for

maximum holding Anti-rotation fins
power
Low profile head
Description
The RamToggle™ is a one piece, light duty nylon cavity fastener.
Specification
Material Nylon
Head Style Flush
Screw Gauges 6-8
Hole Diameters 8mm
Required Screw Lengths 30mm, 35mm, 40mm
Maximum Wall Thickness’ 5mm-10mm, 8mm-12mm, 12mm-18mm
Substrates Plasterboard

• The RamToggle™ features a wide wingspan for maximum holding power 1. Drill an 8mm hole through the plasterboard.
• Anti-rotation fins prevent spinning in the hole when installing the screw. 2. Compress the wings of the RamToggle™ and insert the anchor into the
• The low-profile head allows for flush fixing. hole. If necessary, tap with a hammer to ensure a flush fit with the surface.
• The nylon body is non-conductive. 3. The wings will spread behind the cavity wall.
4. Insert the appropriate gauge screw through the fixture, into the
Related Products RamToggle™ and tighten, pulling the wings of the anchor firm against the
Drill, Drill Bits, Drill Driver, Screw Gun, Screwdriver Bits cavity wall.
RamToggle™ - Nylon Cavity Fastener
Part No Hole Screw Wall Order
Ø (mm) Gauge Thickness (mm) Qty
RT10 8 6-8 5-10 100
RT12 8 6-8 8-12 100
RT16 8 6-8 12-18 100

Self Drilling Screws

Plasterboard
Available in either needle or drill point
Some sizes available

collated as pictured
Bugle head pulls

down neatly below
the surface of the
plasterboard
without damaging
the board or the
face paper
Description
Ramset™ Self Drilling Plasterboard Screws are designed for fixing
plasterboard to timber or light gauge steel.
Specification
Material Fine Grain High Carbon Steel
Head Style Bugle - Phillips
Point Styles Needle, Drill
Thread Styles Twinfast, Coarse
Fixing Method Through Fixing
Setting Method Rotation Features & Benefits
Anchoring Method Thread Forming • Ramset™ Self Drilling Plasterboard Screws are manufactured from fine
Screw Gauges 6, 7, 8, 10 grain high carbon steel and are heat treated for strength.
Thread Pitch’s 8, 9, 15, 16, 18, 20 • The bugle head pulls down neatly below the surface of the plasterboard
Screw Lengths 25mm, 30mm, 32mm, 38mm, 40mm, without damaging the board or the face paper.
41mm, 45mm, 65mm • Ramset™ Self Drilling Plasterboard Screws can be used for either wall or
Max Steel Thickness Needle Point - 0.6mm, Drill Point - 2.3mm ceiling fixing.
Substrates Timber, Light Gauge Steel • Available loose or collated.
Related Products
Drill Driver
Screw Gun
Screwdriver Bits

Plasterboard

Fixing Plasterboard Ceilings 4
Fixing Plasterboard Walls 4

Installation
1. Using a drill driver or screw gun, insert the point of a Philips Head screw
driver bit into the recess of the screw, place the screw point against the
plasterboard surface, lightly piercing the face paper, and drive the screw
into the plaster board until the head is flush with the surface.
Needle Point Needle Point Drill Point

Twinfast Thread Coarse Thread Twinfast Thread
Self Drilling Plasterboard Screws

Part No Head Style Point Style Thread Style Collated/Loose Gauge Pitch Length Order Qty
RSN06025YBTC Bugle Head Needle Twinfast Collated 6 18 25mm 1000
RSN06025YBT Bugle Head Needle Twinfast Loose 6 18 25mm 1000
RSN07025YBF Bugle Head Needle Coarse Loose 7 9 25mm 1000
RSD06025YBTC Bugle Head Drill Point Twinfast Collated 6 18 25mm 1000
RSD06025YBB Bugle Head Drill Point Twinfast Loose 6 20 25mm 1000

Metal
Multiple Head Styles for

a variety of applications
Available in either needle or drill point
Fine thread pitch

for metal tapping
Pictured - Drill Point Large Wafer (Truss) Head
Description
Ramset™ Self Drilling Metal Screws drill, tap and fasten into steel up to
6mm thick in one single operation, eliminating alignment problems and
increasing fastening speed.
Specification
Corrosion Protection Zinc Plating, XP3™ (AS3566 Class 3)
Head Style Wafer, Large Wafer (Truss), Flat - Phillips
Hex Washer - Hex
Point Styles Needle, Drill, Extended Drill
Thread Styles Metal
Fixing Method Through Fixing Features & Benefits
Setting Method Rotation • Ramset™ Self Drilling Metal Screws are manufactured from fine
Anchoring Method Thread Forming grain high carbon steel and are heat treated for strength.
Screw Gauges 8, 10, 12 • Available in a range of popular head styles for a variety of applications.
Thread Pitch’s 16, 18, 24 • Fine thread pitch for metal tapping.
Screw Lengths 12mm, 16mm, 32mm, 50mm
Max Steel Thickness Needle Point - 0.6mm,
8g Drill Point - 2.5mm,
10g Drill Point - 3.5mm,
Extended Drill Point - 12.0mm
Substrates Steel
Related Products
Drill Driver
Screw Gun
Screwdriver Bits

Metal

Building Contractor Signwriter Electrical Contractor Ceiling & Partitioning Contractor
Fixing Foil Insulation 4
Sign Installation 4
Stud to Track Fixing 4

Installation
1. Using a drill driver or screw gun set to approx 2500rpm, insert the point of
a Philips Head screwdriver bit into the recess of the screw, place the screw
point against the surface to be fastened, push sharply to create a starting
point, and drive the screw into the material with firm pressure until the
head is flush with the surface.
Needle Point *Extended Drill Point Drill Point

Flat Head Hex Washer Head Wafer Head
(XP3™ AS3566 Class 3
corrosion protection)
Self Drilling Metal Screws

Part No. Head Style Point Style Thread Style Collated/Loose Gauge Pitch Length Order Qty
RSD08012YLB Large Wafer (Truss) Drill Point Metal Loose 8 18 12mm 1000
RSD08016YLB Large Wafer (Truss) Drill Point Metal Loose 8 18 16mm 1000
RSD08012YWB Wafer Drill Point Metal Loose 8 18 12mm 1000

RSD10016YWB Wafer Drill Point Metal Loose 10 16 16mm 1000
RQ512032MHC* Hex Washer Extended Drill Point Metal Loose 12 24 32mm 1000
RQ512050MHC* Hex Washer Extended Drill Point Metal Loose 12 24 50mm 1000
RNPSHZY1016 Flat Needle Point Metal Loose 10 16 16mm 1000

RSDSHZY1016 Flat Drill Point Metal Loose 10 16 16mm 1000

Particleboard
Countersunk rib head for flush finish

Coarse thread pitch for maximum

grip and minimum stripout
Needle point
Description
Ramset™ Self Drilling Particleboard Screws are designed for attaching
particleboard and soft timbers to particleboard or soft timbers. Ideal for
furniture, cabinet making and office partitioning applications.
Specification
Head Style Countersunk Rib - Phillips
Point Styles Needle
Thread Styles Coarse
Anchoring Method Thread Forming • Ramset™ Self Drilling Particleboard Screws are manufactured from fine
Screw Gauge 8 grain high carbon steel and heat treated for strength.
Thread Pitch 10 • The countersunk rib head self-embeds below the surface of the
Screw Lengths 20mm, 25mm, 28mm, 32mm, 40mm, particleboard or timber for a flush finish.
45mm, 50mm • Coarse thread for maximum grip and minimum stripout.
Substrates Particleboard (Chipboard, MDF), Soft Timber
Related Products
Drill Driver
Screw Gun
Screwdriver Bits

Particleboard

Ceiling & Partitioning Contractor Building Contractor Cabinet Maker
Office Partitioning Installation 4
Brace Board Installation 4
Cabinet Construction & Installation 4

Installation
1. Using a drill driver or screw gun set to approx 1000rpm, insert the point of
a Philips Head screwdriver bit into the recess of the screw, place the screw
point, and drive the screw into the material until the head is flush with the
surface.
Self Drilling Partical Board Screws

RSC08020YSF Countersunk Rib Needle Coarse Loose 8 10 20mm 1000

Cabinet
Large wafer (truss) head for fixing jobs

that require a broad low profile head
Twinfast thread for fixing to timber
Description
Ramset™ Self Drilling Cabinet Screws are designed for attaching
particleboard, timber, insulation foil or sheet metal to timber. Ideal for
furniture, cabinet making, signage, foil insulation and office partitioning
applications.
Specification
Head Style Large Wafer (Truss) - Phillips
Point Styles Needle
Thread Styles Twinfast
Anchoring Method Thread Forming • Ramset™ Self Drilling Cabinet Screws are manufactured from fine
Screw Gauges 8 grain high carbon steel and heat treated for strength.
Thread Pitch’s 15 • The large wafer head is ideal for jobs that require a broad, low-profile
Screw Lengths 12mm, 16mm, 25mm head.
Substrates Timber • Twinfast thread for maximum grip in timber.
Related Products
Drill Driver
Screw Gun
Screwdriver Bits

Cabinet

Building Contractor Signwriter Cabinet Maker
Fixing Foil Insulation 4
Sign Installation 4
Cabinet Construction & Installation 4

Installation
1. Using a drill driver or screw gun, insert the point of a Philips Head
screwdriver bit into the recess of the screw, place the screw
point, and drive the screw into the material until the head is flush with the
surface.
Self Drilling Cabinet Screws

RSN08012YLT Large Wafer (Truss) Needle Twinfast Loose 8 15 12mm 1000

Cement Sheet
Countersunk rib head for flush finish

Different thread &

point styles for fixing
to timber or steel
Pictured - Needle Point Twinfast Thread
Description
Ramset™ Self Drilling Cement Sheet Screws are designed for fixing
cement sheet to timber or steel.
Specification
Corrosion Protection Zinc Plating, XP3™ (AS3566 Class 3)
Head Style Countersunk Rib - Phillips
Point Styles Needle, Winged Drill
Thread Styles Twinfast, Metal
Anchoring Method Thread Forming • Ramset™ Self Drilling Cement Sheet Screws are manufactured from
Screw Gauges 8, 10 fine grain high carbon steel and heat treated for strength.
Thread Pitch’s 15, 16, 18 • The countersunk rib head self-embeds below the surface of the cement
Screw Lengths 20mm, 22mm, 30mm, 32mm, 40mm, sheet for a flush finish.
45mm • Available for fixing to both timber and steel.
Substrates Timber, Steel
Related Products
Drill Driver
Screw Gun
Screwdriver Bits

Cement Sheet

Ceiling & Partitioning Contractor Building Contractor Tiler
Wall Lining Installation 4
Cladding Installation 4
Underlay Installation 4

Installation
1. Using a drill driver or screw gun set to approx 2500rpm for winged drill
point or 1500rpm for needle point, insert the point of a Philips Head screw
driver bit into the recess of the screw, place the screw point against the
surface to be fastened, push sharply to create a starting point, and drive
the screw into the material maintaing firm pressure, until the head is flush
with the surface.
*Winged Drill Point Winged Drill Point

Metal Thread Metal Thread
(XP3™ AS3566 Class 3
corrosion protection)
Self Drilling Cement Sheet Screws

Part No. Head Style Point Style Thread Style Collated/Loose Gauge Pitch Length Order Qty
RSN08020YST Countersunk Rib Needle Twinfast Loose 8 15 20mm 1000
RSN08030YST Countersunk Rib Needle Twinfast Loose 8 15 30mm 1000
RSD08022MSBW* Countersunk Rib Winged Drill Point Metal Loose 8 18 22mm 1000
RSD10045YSBW Countersunk Rib Winged Drill Point Metal Loose 10 16 45mm 1000

Chemical
Anchoring
The Ramset™ Chemical Anchoring range consists

of ChemSet™ Injection Adhesives and ChemSet™
Maxima™ glass capsules. ChemSet™ is the
leading Chemical Anchoring brand in Australia
due to its high quality, reliability and versatility.
The versatile ChemSet™ range provides different

options of cost and performance for anchoring
threaded studs, reinforcing bars and starter
bars into solid and hollow substrates.
Only ChemSet™ Injection anchoring adhesive

cartridges have the unique tap valve, which is
essential to preserve contents of part used
cartridges for use later on, the next day or even
the next job.
ChemSet™ is the specifiers’ choice, with easy

to use engineering data created by Ramset™
engineering professionals and backed by
rigorous testing at the Ramset™ Product
Engineering Laboratory.

Chemical
Anchoring

Contents
Chemical Anchoring
Introduction 84
Selection Guide 85
Injection Adhesives 86
• ChemSet Reo 502
™ ™
• ChemSet™ 801
• Structaset™ 401
• ChemSet™ 101
• UltraFix™ Plus
Maxima™ Anchoring Capsules 96
ChemSet™ Anchor Fixings 98

• ChemSet™ Anchor Studs
• Remedial Wall Ties
• Threaded Inserts
• Hollow Block & Brick Anchoring Accessories
ChemSet™ Anchoring Accessories 106

• ChemSet Injection Applicators
™
• Hole Cleaning Accessories

• Static Mixing Nozzles
Installation Guide 108

Estimating Charts 112
Introduction
Chemical Anchoring
About ChemSet™ Structaset™ 401

Ramset introduced chemical anchoring into Australia in 1981 in the form of
™
Fast cure, heavy duty anchoring of threaded studs and reinforcing bars in
ChemSet™ glass capsules. The product grew in popularity due to its close to solid and hollow substrates.
edge and close anchor spacing advantages and its ease of use. For carbide or diamond drilled holes in solid concrete, stone, solid brick,
hollow brick and hollow concrete block.
Since then the name ChemSet™ has entered into every day language on
building sites across Australia.
ChemSet™ Injection 101
Over the last 20+ years Ramset has extended the ChemSet™ range to Fast cure, medium duty anchoring of threaded studs and reinforcing bars in
include injection adhesives and accessories to enable ChemSet™ to be used solid and hollow substrates.
in a broader range of applications. For carbide drilled holes in solid concrete, stone, solid brick, hollow brick and
Introduction
hollow concrete block.
Today the ChemSet™ Chemical Anchoring range is still the leading brand in
Australia due to its high quality, reliability and versatility. Ultrafix™ Plus
Fast cure, medium duty anchoring of threaded studs in solid and hollow
ChemSet™ is the specifiers’ choice, with easy to use engineering data substrates in handy 300 ml tube that fits standard silicone caulking gun
created by Ramset™ engineering professionals and backed by rigorous For carbide drilled holes in solid concrete, stone, solid brick, hollow brick and
testing at the Ramset™ Product Engineering Laboratory in Melbourne. hollow concrete block.
Ramset’s conservative method of deriving load capacity means engineers
can specify ChemSet™ adhesives with confidence that the connections will
be safe and reliable. ChemSet™ Maxima™ Spin Capsules
Rapid cure, extra heavy duty anchoring of threaded studs in small jobs with
The story continues into the future with Ramset continuing to expand the
™ few fixings.
range with new products to improve ease of use, strength, safety and lift site For carbide or diamond drilled holes in solid concrete, stone and solid brick;
productivity. dry, wet or even underwater.
ChemSet™ Chemical Anchoring Range

The ChemSet™ Chemical Anchoring range consists of ChemSet™ Injection
Adhesives and ChemSet™ Maxima™ glass capsules.
Central to the ChemSet™ Injection range is the unique ChemSet™ Universal

Applicator that dispenses all of the ChemSet™ Injection adhesives. The
advantage is that contractors can change ChemSet™ adhesive or pack size
without having to purchase another applicator.
Got a BIG job with lots of fixings? The ChemSet™ pneumatic powered
Universal Applicator will make the job easier and faster with less fatigue.
Only ChemSet™ Injection anchoring adhesive cartridges have the unique tap
valve, which is essential to preserve contents of part used cartridges for use
later on, the next day or even the next job.
The ChemSet™ Chemical Anchoring range consists of 6 specialised products,

each available in different pack sizes to suit different jobs.
ChemSet™ Reo502™
Best Bar Anchoring….Bar none
Extra heavy duty epoxy adhesive for reinforcing bars and threaded studs.
For carbide or diamond drilled holes in solid concrete, stone and solid brick;
dry, wet, or even flooded.
ChemSet™ Injection 801

Heavy duty anchoring of threaded studs and reinforcing bars in corrosive
environments.
For carbide or diamond drilled holes in solid concrete, stone and solid brick.

Selection Guide
Chemical Anchoring
Which ChemSet™ anchoring adhesive should I use?
Product UltrFix™ Plus ChemSet™ Injection ChemSet

Maxima™
Property 101 Structaset™ 401 801 Reo 502™ Spin Capsules
Chemical Type Polyester Polyester Epoxy Acrylate Epoxy Epoxy Acrylic
Working Time (min) @ 20°C 6 to 10 5 to 10 6 6 to 10 15 to 20 2 to 3
Loading Time @ 20°C 50 Minutes 90 Minutes 50 Minutes 14 Hours 3 Hours 20 Minutes
Selection Guide
Min Installation Temp (°C) 0 0 0 5 5 -5
Max Installation Temp (°C) 35 43 40 40 40 43
Dry Holes 4 4 4 4 4 4
Damp Holes 4 4 4 4 4
Wet Holes (Water removed) 4 4
Flooded Holes 4 4
Underwater 4 4
For Anchoring Into
Solid Concrete 4 4 4 4 4 4
Stone 4 4 4 4 4 4
Masonry 4 4 4 4 4 4
Hollow Masonry 4 4 4
Brick Work 4 4 4
Hole Orientation
Vertical Down 4 4 4 4 4 4
Horizontal 4 4 4 4 4 4
Vertical Up (Overhead) 4 4 4 Contact Ramset™
Contact Ramset™
4
Drill Type
Carbide Drilled 4 4 4 4 4 4
Diamond Drilled 4 4 4 4
Properties After Cure
Load Capacity 4 4 44 44 444 444
Chemical Resistance 4 4 44 444 44 44
Cyclic Loading 4 4 44 44 444 44
Min Service Temp (°C) -10 -10 -40 -10 -10 -23
Max Service Temp (°C) 80 80 80 80 80 60
Immersion After Cure 4 4 4 4 4 4
Potable Water 4
Suitable Fixings
Threaded Rod - Grade 4.6 4 4 4 4 4 4
Threaded Rod - AISI 304 4 4 4 4 4 4
Threaded Rod - AISI 316 4 4 4 4 4 4
Reinforcing Bar 4 4 4 4 4
Legend
Good ✓
Better ✓✓
Best ✓✓✓
Extra Heavy Duty Anchoring
Tap valve to preserve contents
Robust, puncture
proof packaging
Injection Adhesives
Extension for deep holes

Key Features
• Extra heavy duty epoxy
• Quick 3 hour cure time
• Dry, damp, wet and flooded holes
• Suitable underwater
• Long 20 minute working time for
deep embedment
VmOpliCant
Translucent cartridge to
see remaining contents
Co
Made in Australia
ISNE REO502J (750ml)
Description
Extra heavy duty anchoring of reinforcing bar and threaded studs into solid
concrete and stone.Two-component, high bond strength epoxy adhesive
specially designed for structural connections, such as reinforcing bar.
Suitable for dry, damp, wet and flooded holes. Quick setting for improved
productivity. Long working time to reduce nozzle wastage. Bar development
lengths in accordance with AS3600. Structural reinforcing bar connections in
slabs, columns, beams and walls. Structural steel columns, raker angles,
seating.
Typical Properties
Properties Typical Value
Appearance Part A: White Part B: Black
Mixed: Light Grey
Density 1.28 kg /litre @ 20°C Features & Benefits
Heat Distortion Temperature Approx. 80°C • Quick cure for improved productivity.
Hardness > Shore D 80 • Sag resistant formula for horizontal holes
Compressive Strength (ASTM C579-01) 105 MPa • Bonds to carbide and diamond core drilled holes – strong bond
Dielectric Constant 3.95 • For Grade 500 reinforcing bar
Conductivity 8 x 10-11 ohmS/m • Excellent electrical insulation properties
Service Temperature Limits -10°C to 80°C
Chemical Resistance See Technical Data Sheet
Related Products
DynaDrill™ Impact Wrench
Substrates Solid Concrete, Solid Stone (Proof Wet/Dry Vacuum
Carbide Drill Bits
loading recommended), Solid Brick Hole Cleaning Brushes
Diamond Motor
Diamond Core Drill Bits Hole Cleaning Pump
Concreter Building Civil Steel Balustrade Formworker Bricklayer Fitter
Contractor Contractor Fabricator Contractor
Post-installing reinforcing bar 4 4 4 4
Starter bars 4 4 4 4 4
Threaded studs 4 4 4 4 4

Extra Heavy Duty Anchoring
Installation in Solid Concrete

1. Drill or core hole to specified diameter and depth
2. Remove dust and debris by brushing and blowing 3 times each (If hole is wet
or flooded, brush only remove water and slurry with wet/dry vacuum)
3. Screw mixing nozzle onto cartridge and dispense 2-3 trigger pulls of adhesive
to waste until colour is light grey with no streaks
4. Insert tip of nozzle to bottom of hole and dispense adhesive
5. Fill hole to about 2/3 full
6. Insert threaded stud or reinforcing bar with rotating motion to release
trapped air
Injection Adhesives
7. Wait until adhesive has fully cured before loading (see Working / Loading
Time chart below)
8. Clean up with acetone
Refer to Technical Data Sheet and MSDS available from
www.ramset.com.au, for precautions and further detailed
installation instructions
Recommended Installation Temperatures Hole Condition

Minimum Maximum Hole Condition Suitable
Substrate 5°C 40°C Dry Yes
Adhesive 20°C 32°C Damp Yes
Wet Yes
Working and Loading Time Flooded Yes
Substrate Temperature Gel Time Cure Time Drill Bit Type
(°C) (min) (hours) Carbide Yes
10 21 8 Diamond Core Yes
16 18 5 Hole Orientation
20 20 3 Vertical Down Yes
27 12 2.5 Horizontal Yes
32 8.5 2 Vertical Up (Overhead) Contact Ramset™
ChemSet™ Reo 502™ Anchoring Adhesive

Description Part No Box Quantity Description Part No Box Quantity
Jumbo Cartridge (750 ml) + 1 Nozzle REO502J 12 Hole Cleaning Pump HCP 1
ChemSet™ Universal Applicator CUA 1 Hole Cleaning Pump High Volume HCPHV 1
ChemSet™ Pneumatic Universal Applicator CUAPN 1 Hole Cleaning Brush 13 mm HCBT13 1
Mixing Nozzles for Epoxy with Extension ISNE 5 Hole Cleaning Brush 20 mm HCBT20 1
Mixing Nozzle Turbo (Easier Dispensing) ISNET 1 Hole Cleaning Brush 26 mm HCBT26 1
ChemSet™ Reo 502™ - Indicative Working Loads in 32 MPa Concrete with ChemSet™
Anchor Studs
Thread Drilled Hole Min Hole Tightening Min Edge Min Anchor Max Tensile Max Shear
Size Ø (mm) Depth (mm) Torque (Nm) Distance (mm) Spacing (mm) Load, Na (kN) Load, Vas (kN)*
M8 10 80 10 35 50 6.3 4.4
M10 12 90 20 40 60 10.3 7.1
M12 14 110 40 50 75 15.3 10.5
M16 18 125 95 65 100 29.4 19.9
M20 24 150 180 80 120 37.9 29.9
M20 24 170 180 80 120 43.0 29.9
M24 26 160 315 100 145 40.9 43.3
M24 26 210 315 100 145 53.6 43.3
M30 32 270 600 120 180 72.4 90.4+
M36 38 330 1050 145 220 101.5 131.7+
Bold working load values in tension are limited by steel. All other values limited by concrete and adhesive bond
Working load capacity was derived from characteristic
* For shear acting towards a concrete edge please contact a Ramset Engineer for further design assistance
+ M30 and M36 steel shear values are for Grade 8.8 carbon steel. All other values are for Grade 5.8 carbon steel. ultimate load capacity by applying the following factors:
For water saturated or under water holes, reduce tensile load capacity by 30% Tension: Concrete = 3, Steel = 2.2
Shear: Steel = 2.5
The design engineer should ensure the structural element is capable of supporting these loads.

ChemSet™ 801
Heavy Duty Anchoring
Injection Adhesives
Key Features
• Excellent chemical resistance
• Suitable for use in contact with
drinking water
• Strong bond
VmOpliCant
Co
ISNE C801C (380ml) C801J (750ml)
Description
Heavy duty anchoring of threaded studs and reinforcing bar into solid
concrete and stone in corrosive environments. Two component, chemical
resistant epoxy. Tough and reliable for extra security. High bond strength for
diamond and carbide drilled holes. Steel beams and columns, heavy plant,
safety barriers, reinforcing bars, bottom plate fixing
Typical Properties
Appearance Part A: White Part B: Black
Mixed: Dark Grey
Density 1.30 kg /litre @ 20°C
Heat Distortion Temperature Approx. 80°C
Hardness > Shore D 80
Compressive Strength (AS1012.9) 75 MPa
Water Absorption (ASTM D570) < 0.2% (10 days @ 25°C) Features & Benefits
Modulus of Elasticity > 4 GPa • Carbide and diamond core drilled holes – strong bond
Tensile Strength BS2782 >25 MPa • Excellent chemical resistance
Flexural Strength BS6319 Approx. 22 MPa • Suitable for use in contact with drinking water
Service Temperature Limits -10°C to 80°C • Sag resistant formula for horizontal holes
Contact with Drinking Water AS/NZS4020 • Low odour
PASS
Chemical Resistance See Technical Data Sheet Related Products
Substrates Solid Concrete, Solid Stone DynaDrill™ Impact Wrench
(Proof loading recommended), Carbide Drill Bits Wet/Dry Vacuum
Solid Brick Diamond Motor Hole Cleaning Brushes
Hole Cleaning Pump
Trades & Applications Diamond Core Drill Bits
Concreter Building Civil Steel Balustrade Formworker Bricklayer Fitter Seating
Contractor Contractor Fabricator Contractor Contractor
Threaded Studs 4 4 4 4 4

ChemSet™ 801

2. Remove dust and debris by brushing and blowing 3 times each (If hole is wet
or flooded remove water with wet/dry vacuum and allow to dry)
to waste until colour is dark grey with no streaks
trapped air
Injection Adhesives
Time chart below)
8. Protect from water contact for 24 hours

Adhesive 18°C 35°C Damp No
Wet No
Working and Loading Time Flooded No
Substrate Temperature Working Time Cure / Loading Time Drill Bit Type
25 4 12 Horizontal Yes
30 3 10 Vertical Up (Overhead) Contact Ramset™
ChemSet™ 801 Anchoring Adhesive

Jumbo Cartridge (750 ml) + 1 Nozzle C801J 12 Hole Cleaning Pump HCP 1
Cartridge (380 ml) + 1 Nozzle C801C 24 Hole Cleaning Pump High Volume HCPHV 1
ChemSet™ Universal Applicator CUA 1 Hole Cleaning Brush 13 mm HCBT13 1
ChemSet™ Pneumatic Universal Applicator CUAPN 1 Hole Cleaning Brush 20 mm HCBT20 1
Mixing Nozzles for Epoxy with Extension ISNE 5 Hole Cleaning Brush 26 mm HCBT26 1
Mixing Nozzle Turbo (Easier Dispensing) ISNET 1
ChemSet™ 801 - Indicative Working Loads in 32 MPa Concrete with ChemSet™ Anchor Studs
M8 10 80 10 35 50 6.5 4.4
M10 12 90 20 40 60 9.9 7.1
M12 14 110 40 50 75 14.4 10.5
M16 18 125 95 65 100 19.6 19.9
M20 24 150 180 80 120 28.1 29.9
M20 24 170 180 80 120 33.9 29.9
M24 26 160 315 100 145 33.3 43.3
M24 26 210 315 100 145 50.1 43.3
Bold working load values in tension are limited by steel. All other values limited by concrete and adhesive bond Working load capacity was derived from characteristic
ultimate load capacity by applying the following factors:
Shear values are for Grade 5.8 carbon steel.
Tension: Concrete = 3, Steel = 2.2
Shear: Steel = 2.5

Structaset™ 401
Injection Adhesives
Key Features
• Fast 50 minute cure
• Strong bond
• Low odour styrene free
• Easy dispensing all year round
VmOpliCant
Co
ISNP S401C (380ml) C380A Applicator
Description
Heavy duty Epoxy Acrylate for anchoring threaded studs and reinforcing
bar into solid concrete, stone, hollow brick and hollow concrete block. High
bond strength for diamond and carbide drilled holes. Fast cure for high
productivity. Non-drip formula, ideal for over-head installation. Styrene free
low odour formula. Steel columns, and beams, starter bars, road stitching,
seating, hand rails.
Typical Properties
Appearance Part A: Off White Part B: Black
Mixed: Grey
Density 1.7 g / ml
Substrates Solid Concrete, Solid Brick, Stone
(proof loading recommended), Hollow Features & Benefits
Concrete Block, Hollow Brick • Easy dispensing even in cold weather
• Carbide and diamond drilled holes – strong bond
• Fast cure for high productivity
Related Products
Carbide Drill Bits Wet/Dry Vacuum
Diamond Motor Hole Cleaning Brushes
Trades & Applications Diamond Core Drill Bits Hole Cleaning Pump
Concreter Building Civil Contractor Steel Fabricator Balustrade Formworker

Contractor Contractor
Threaded Studs 4 4 4 4
Starter bars 4 4 4 4
Hollow Masonry Sleeves 4 4 4
Threaded Inserts 4 4 4

Structaset™ 401

2. Remove dust and debris by brushing and blowing 3 times each (if hole is wet
or flooded, remove excess water using wet/dry vacuum)
to waste until colour is grey with no streaks
6. Insert fixing with rotating motion to release trapped air
7. Wait until adhesive has fully cured before loading (see Working Time /
Injection Adhesives
Loading Time chart below)
8. Clean up with Acetone

Wet No
(°C) (min) (min) Carbide Yes
30 4 35 Vertical Up (Overhead) Yes
Structaset™ 401 Anchoring Adhesive

Cartridge (380 ml) + 1 Nozzle S401C 12 Hole Cleaning Brush 13 mm HCBT13 1
ChemSet™ Applicator 380ml* C380A 1 Hole Cleaning Brush 20 mm HCBT20 1
Mixing Nozzles for Polyester ISNP 5 Hole Cleaning Brush 26 mm HCBT26 1
Hole Cleaning Pump HCP 1 Nylon Sleeves for Hollow Block See Page 104 100
Hole Cleaning Pump High Volume HCPHV 1 Fine Metal Mesh Sleeves See Page 104 100
* Introductory pack size not suitable for ChemSet™ Universal Applicator
Structaset™ 401 - Indicative Working Loads in 32 MPa Concrete with ChemSet™ Anchor
Studs
M8 10 80 10 35 50 6.5 4.4
M10 12 90 20 40 60 10.1 7.1
M12 14 110 40 50 75 15.3 10.5
M16 18 125 95 65 100 20.8 19.9
M20 24 150 180 80 120 24.4 29.9
M20 24 170 180 80 120 27.7 29.9
M24 26 160 315 100 145 33.0 43.3
M24 26 210 315 100 145 43.3 43.3
Shear: Steel = 2.5

ChemSet™ 101
Medium Duty Anchoring
Key Features
VmOpliCant • Fast cure
• Solid and hollow substrates
Co • Easy dispensing all year round
Injection Adhesives
ISNP C101C (380ml) C101J (750ml) ISKP (2 x 380ml)
Description
Fast cure, medium duty anchoring of threaded studs and reinforcing bar into
solid concrete, stone, hollow brick and hollow concrete block.
Versatile, multi-purpose two part polyester anchoring system. Fast cure for
high productivity. Non-drip formula, ideal for overhead installation.
Steel columns and beams, seating, machinery, facade pins, handrails, gates,
starter bars, bottom plate fixing
Typical Properties
Appearance Part A: Mauve Part B: Green
Mixed: Green / Grey
Compressive Strength 20 MPa Features & Benefits
(AS1012.9) • Easy dispensing, even in cold weather
Service Temperature Limits -10°C to 80°C • Sag resistant formula for horizontal holes and overhead applications
• Tap Valve to preserve contents between uses
Chemical Resistance See Technical Data Sheet
Substrates Solid Concrete, Solid Stone (Proof Related Products
loading recommended), Solid Brick, DynaDrill™ Wet/Dry Vacuum
Hollow Concrete Block, Hollow Brick Carbide Drill Bits Hole Cleaning Brushes
Impact Wrench Hole Cleaning Pump
Concreter Building Civil Steel Balustrade Form Bricklayer Fitter Seating Facade
Contractor Contractor Fabricator Contractor worker Contractor Contractor
Threaded Studs 4 4 4 4 4 4
Hollow Masonry Sleeves 4 4 4 4
Remedial Wall Ties 4 4

ChemSet™ 101

1. Drill hole to specified diameter and depth
2. Remove dust and debris by brushing and blowing 3 times each (If hole is
wet or flooded, remove excess water with wet/dry vacuum)
3. Screw mixing nozzle onto cartridge and dispense 2-3 trigger pulls of
adhesive to waste until colour is green / grey with no streaks
trapped air
Injection Adhesives
7. Wait until adhesive has fully cured before loading (see Working /

Wet No
0 40 7 Diamond Core No
20 5 - 10 1.5 Vertical Down Yes
40 4 0.75 Vertical Up (Overhead) Yes
ChemSet™ 101 Anchoring Adhesive

Jumbo Cartridge (750 ml) + 1 Nozzle C101J 12 Hole Cleaning Pump High Volume HCPHV 1
Cartridge (380 ml) + 1 Nozzle C101C 20 Hole Cleaning Brush 13 mm HCBT13 1
2 x Cartridges (380 ml) + 4 Nozzles ISKP 10 Hole Cleaning Brush 20 mm HCBT20 1
ChemSet™ Universal Applicator CUA 1 Hole Cleaning Brush 26 mm HCBT26 1
ChemSet™ Pneumatic Universal Applicator CUAPN 1 Nylon Sleeves for Hollow Block See Page 104 100
Mixing Nozzles for Polyester ISNP 5 Fine Metal Mesh Sleeves See Page 104 100
Hole Cleaning Pump HCP 1
ChemSet™ 101 - Indicative Working Loads in 32 MPa Concrete with ChemSet™ Anchor
Studs
M8 10 80 10 35 50 4.5 4.4
M10 12 90 20 40 60 6.0 7.1
M12 14 110 40 50 75 8.6 10.5
M16 18 125 95 65 100 13.5 19.9
M20 24 150 180 80 120 22.3 29.9
M20 24 170 180 80 120 25.2 29.9
M24 26 160 315 100 145 32.7 43.3
M24 26 210 315 100 145 42.9 43.3
Shear: Steel = 2.5

UltraFix™ Plus
Injection Adhesives
Key Features
• Fast cure
• Solid and hollow substrates
• Low odour
• Easy dispensing
• Fits standard silicone
caulking gun
VmOpliCant
Co
UFP300 (300ml)
Description
Fast cure, medium duty anchoring of threaded studs and reinforcing bar into
solid concrete, stone, hollow brick and hollow concrete block.
Versatile, multi-purpose two part polyester anchoring system. For standard
silicone caulking gun. Great for small jobs or around the home.
Steel fencing, gates, brackets, hinges, guard rails, hand rails
Typical Properties
Appearance Part A: Cream Part B: Black
Mixed: Grey
Compressive Strength 20 MPa Features & Benefits
(AS1012.9) • Easy dispensing, even in cold weather
Service Temperature Limits -10°C to 80°C • Sag resistant formula for horizontal holes and overhead applications
Substrates Solid Concrete, Solid Stone (Proof loading • Low odour
recommended), Solid Brick, Hollow
Concrete Block, Hollow Brick
Related Products
DynaDrill™ Wet/Dry Vacuum
Carbide Drill Bits Hole Cleaning Brushes
Impact Wrench Hole Cleaning Pump
Concreter Building Civil Steel Balustrade Formworker Bricklayer Fitter Seating
Contractor Contractor Fabricator Contractor Contractor
Threaded Studs 4 4 4 4 4
Starter Bars 4 4 4 4 4
Hollow Masonry 4 4 4 4
Sleeves

UltraFix™ Plus

1. Drill hole to specified diameter and depth
wet or flooded, remove excess water with wet/dry vacuum)
adhesive to waste until colour is grey with no streaks
trapped air
Injection Adhesives
7. Wait until adhesive has fully cured before loading (see Working /

Wet No
Substrate Temperature Working Time Cure / Loading Time Drill Bit Type
(°C) (min) (min) Carbide Yes
5 18 145 Diamond Core No
30 4 35 Vertical Up (Overhead) Yes
Ultrafix™ Plus Anchoring Adhesive

Cartridge (300 ml) + 2 Nozzles UFP300P 10 Hole Cleaning Brush 13 mm HCBT13 1
Cartridge (300 ml) + 2 Nozzles UFP300 4 Hole Cleaning Brush 20 mm HCBT20 1
Caulking Gun for 300 ml Cartridges CAGU300 1 Hole Cleaning Brush 26 mm HCBT26 1
Mixing Nozzles for Polyester ISNP 5 Nylon Sleeves for Hollow Block See Page 104 100
Hole Cleaning Pump HCP 1 Fine Metal Mesh Sleeves See Page 104 100
Hole Cleaning Pump High Volume HCPHV 1
Ultrafix™ Plus - Indicative Working Loads in 32 MPa Concrete with ChemSet™ Anchor
Studs
M8 10 80 10 35 50 4.5 4.4
M10 12 90 20 40 60 6.0 7.1
M12 14 110 40 50 75 8.6 10.5
M16 18 125 95 65 100 13.5 19.9
M20 24 150 180 80 120 22.3 29.9
M20 24 170 180 80 120 25.2 29.9
M24 26 160 315 100 145 32.7 43.3
M24 26 210 315 100 145 42.9 43.3
Bold working load values in tension are limited by steel. All other values limited by concrete and adhesive bond
Working load capacity was derived from characteristic
Shear: Steel = 2.5

ChemSet™ Maxima™
Anchoring Capsules
Anchoring Capsules
Key Features
• Fast cure
• No mixing, no waste
• One capsule per fixing
• Use underwater
VmOpliCant
Co
Description
Rapid cure, extra heavy duty anchoring of threaded studs into solid concrete
and stone. For small jobs with few fixings. One capsule for one hole - no
mixing, no mess, no waste. Carbide or diamond drilled holes. Dry, wet or
even underwater. Cures in 30 minutes! Balustrade posts, fencing, sheds,
structural steel columns, hand rails, seating, machinery hold down
Typical Properties
Appearance Part A: Clear Honey
Part B: White Powder
Mixed: Dark Grey
Substrates Solid Concrete, Solis Stone (Proof
loading recommended), Solid Brick Features & Benefits
• Non-drip formula for horizontal holes and overhead applications
• Glass becomes part of the aggregate
• No applicator
• Strong bond for extra security
Related Products
Building Civil Contractor Steel Fabricator Balustrade Fitter Seating Contractor
Contractor Contractor
Threaded Studs 4 4 4 4 4 4

ChemSet™ Maxima™
Anchoring Capsules

wet or flooded, brush only)
3. Insert capsule into hole
4. Fit socket into drill and use to rotate and drive a ChemSet™ Anchor
Stud into the hole
5. The stud rotation will mix the capsule contents
6. Wait until adhesive has fully cured before loading (see Loading Time
Anchoring Capsules
chart below)

Substrate -5°C 43°C Dry Yes
Adhesive -5°C 43°C Damp Yes
Wet Yes
Working and Loading Time Flooded Yes
Drill Bit Type
Substrate Temperature Cure / Loading Time
(°C) (min) Carbide Yes
Dry Damp or Wet Diamond Core Yes
≥ 20 20 40 Hole Orientation
10 to 20 30 60 Vertical Down Yes
0 to 10 60 120 Horizontal Yes
-5 to 0 5 hours 10 hours Vertical Up (Overhead) Yes
ChemSet™ Maxima™ Anchoring Capsule

ChemSet™ Maxima™ Capsule M8 CHEM08 10 Hole Cleaning Pump HCP 1
ChemSet™ Maxima™ Capsule M10 CHEM10 10 Hole Cleaning Pump High Volume HCPHV 1
ChemSet™ Maxima™ Capsule M12 CHEM12 10 Hole Cleaning Brush 13 mm HCBT13 1
ChemSet™ Maxima™ Capsule M24 CHEM2024 6
ChemSet™ Maxima™ - Indicative Working Loads in 32 MPa Concrete with ChemSet™

Anchor Studs
M8 10 80 10 35 50 6.5 4.4
M10 12 90 20 40 60 10.3 7.1
M12 14 110 40 50 75 15.3 10.5
M16 18 125 95 65 100 22.3 19.9
M20 24 150 180 80 120 35.7 29.9
M20 24 170 180 80 120 40.5 29.9
M24 26 160 315 100 145 41.3 43.3
M24 26 210 315 100 145 54.2 43.3
* For shear acting towards a concrete edge please contact a Ramset Engineer for further design assistance ultimate load capacity by applying the following factors:
Shear: Steel = 2.5

ChemSet™ Anchor
Steel Threaded Studs
External hex drive

• Reliable socket fit
• Does not collect water
ChemSet™ Anchor Fixings
Depth set mark for

accurate embedment
High quality zinc

plating and galvanising
to Australian standards
Heavy Duty Grade 5.8
carbon steel or
AISI Grade 318 stainless Bevelled tip
• Releases trapped air
• Prevents unthreading
Description
ChemSet™ Anchor Studs are made from Grade 5.8 carbon steel to get the
most out of adhesive tensile capacities and provide higher shear capacities
than regular Grade 4.6 grade studs. Galvanising of ChemSet Anchor Studs
meets Australian Standards. Stainless Steel ChemSet™ Anchor Studs are
high corrosion resistant AISI 316 (A4).
Specification
Material - Bolt Carbon Steel, Stainless Steel 316 (A4)
Head Styles Hex Nut
Setting Method Chemical
Anchoring Method Chemical
Thread Diameters M8, M10, M12, M16, M20, M24
Anchor/Hole Diameters 10mm, 12mm, 14mm, 18mm, 24mm, 26mm
Anchor Lengths 110mm, 130mm, 160mm, 190mm, 260mm, Features and Benefits
300mm • High Performance Grade 5.8 Carbon Steel
Maximum Fixture Thickness’ 15mm, 25mm, 30mm, 50mm, 40mm, • Zinc Plated for indoor or dry climates
45mm, 80mm, 90mm, 105mm • Hot dip galvanised to AS1650 and AS1214
Substrates Concrete, Solid Brickwork • Hot dip galvanised to 42 micron for exterior applications
• High Performance AISI316 Stainless Steel for Coastal Applications
• Pre-cut to standard chemical anchoring lengths
• Supplied with nuts and washers
• Depth set mark to ensure correct embedment
• Reliable external hex drive for installing capsules
• Ramset™ Quality
Related Products

ChemSet™ Anchor
Steel Threaded Studs

Building Steel Fabricator Balustrade Bricklayer Fitter Seating Facade
Contractor Contractor Contractor Contractor
Machinery hold 4
down
Structural steel 4

connections
Seating 4 4
Hand rails 4 4 4
Fencing 4 4 4
Installation
See recommendations for each ChemSet™ anchoring adhesive
on previous pages.
ChemSet™ Anchor Studs

ChemSet™ Anchor Stud M8 x 110 Zinc CS08110 10 ChemSet™ Anchor Stud M16 x 190 Zinc CS12190 10
ChemSet™ Anchor Stud M8 x 110 Galvanised CS08110GH 10 ChemSet™ Anchor Stud M16 x 190 Galvanised CS12190GH 10
ChemSet™ Anchor Stud M8 x 110 Stainless CS08110SS 10 ChemSet™ Anchor Stud M16 x 190 Stainless CS12190SS 10
ChemSet™ Anchor Stud M12 x 180 Zinc CS12180 10 Other sizes and steel types available on request.
(Maybe subject to lead time)
ChemSet™ Anchor Studs - Typical Properties

See working loads of each anchoring adhesive in previous pages
Thread Overall Length, Effective Max Fixture Yield Strength, Carbon Steel Yield Strength, Stainless Steel Section
Size L (mm) Length, Le Thickness, t fy UTS, fu fy UTS, fu Modulus, Z
(mm) (mm) (MPa) (MPa) (MPa) (MPa) (mm3)
M8 110 95 15 430 540 450 650 31.2
M10 130 115 25 430 540 450 650 62.3
M12 160 140 30 430 540 450 650 109.2
M12 180 160 50 430 540 450 650 109.2
M16 190 165 40 420 520 450 650 277.5
M20 260 225 80 420 520 450 650 540.9
M24 300 265 105 420 520 450 650 935.5

Remedial Wall Ties
Corrosion resistant
reinforced nylon
Spiral form locks

into adhesive
Plunger
Drip condensor
prevents water
transfer
Outer sleeve
Remedial Wall Ties

An innovative high strength, corrosion resistant nylon solution to replacing
corroded brick ties. Fast and easy to install.
Typical Properties
Property Typical Value
Overall Length 220.0 mm
Nominal Diameter 12 mm
Material Glass Filled Nylon
Service Temperature -5°C to 40°C
Yield Strength Tension ASTM D638 170 MPa
Substrates Solid Brick, Solid Concrete
Quantity of Wall Ties Per ChemSet™ 101 Pack

Features and Benefits
Pack Size Quantity Of Wall Ties • High strength, corrosion resistant glass reinforced nylon
380ml 48 • No expansion stress on bricks
• Non-destructive installation
750ml 98
• Easy, simple and quick to install
• Install from either side of the wall
• No setting tool required
• Fast setting time (in conjunction with ChemSet™ 101 and Ultrafix™ Plus)
Trades & Applications • Recessed for neat finish
• Designed to prevent water transfer between cavities
Brick Layer
• Suitable for installation in damp conditions (with ChemSet™ 101 and
Replacing Brick Ties 4 Ultrafix™ Plus)
Related Products
DynaDrill™ Diamond Core Drill Bits
Carbide Drill Bits Hole Cleaning Brushes
Diamond Motor Hole Cleaning Pump

Remedial Wall Ties
Installation
1. Drill a 12 mm diameter hole in solid brick using a masonry drill bit all the
way through the nearest brick and maximum 70 mm into the second brick

2. Brush and blow dust out of holes
3. Insert outer sleeve through first brick into the second until it reaches the
back of the hole
4. Insert ChemSet 101 or Ultrafix™ Plus mixing nozzle into outer sleeve
and dispense adhesive until sleeve is full
5. Insert the wall tie plunger into the outer sleeve all the way in
6. Adhesive will cure and hold the two brick leaves together

Characteristic Loads in Red Clay Brick at

1.5 mm deflection with ChemSet™ 101
Characteristic Load
Tension 0.87 kN
Compression 2.05 kN
Remedial Wall Ties

Description Part No Box Quantity
Remedial Wall Tie RA225 100

Threaded Inserts
Chemical Injection
Anti-rotation grooves
assist application of torque
Multiple cones
lock into adhesive
Cap protects threads
from dust and adhesive
Description
Internally threaded steel inserts are for use with ChemSet™ injection
Adhesives. Available in zinc plated carbon steel or high corrosion resistant
ASIS 316 (A4). Ideal for applications where a bolt finish is required.
Typical Properties
500 MPa Carbon Steel
Steel Grades
AISI 316 (A4) Stainless Steel
Features and Benefits

• High Performance Grade 5.8 Carbon Steel
• Zinc Plated for indoor or dry climates
• High Performance AISI316 Stainless Steel for Coastal or fresh water
Applications
• Supplied with protective cap to protect threads during installation
Related Products
Carbide Drill Bits Structaset™ 401
Diamond Motor ChemSet™ 801
Diamond Core Drill Bits ChemSet™ Reo502™
Hole Cleaning Brushes

Threaded Inserts
Chemical Injection

Building Steel Fabricator Balustrade Fitter Seating Facade Contractor
Contractor Contractor Contractor
Structural steel connections 4

Seating 4 4
Hand rails 4 4 4
Balustrade posts 4
Installation
wet or flooded, consult adhesive product information to determine its suit
ability for this condition)
adhesive to waste until colour is grey with no streaks
6. Insert threaded insert with rotating motion to release trapped air
Time chart for each adhesive)
Typical Properties
Thread Size Overall Length, Effective Length, Thread Length, Carbon Steel Stainless Steel
L (mm) Le (mm) L2 (mm) Tensile Yield UTS, fu Yield Strength, fy UTS, fu
Strength, fy (MPa) (MPa) (MPa
(MPa)
M8 60 60 25 420 520 350 650
M10 65 65 32 420 520 350 650
M12 75 75 38 420 520 350 650
M16 125 125 50 420 520 - -
M20 170 170 63 420 520 - -
Threaded Inserts (Available on request. Lead time applies)

Threaded Insert M8 x 60 Zinc 062770 10 Threaded Insert M12 x 75 Stainless 063100 10
Threaded Insert M8 x 60 Stainless 062860 10 Threaded Insert M16 x 125 Zinc 062800 10
Threaded Insert M10 x 65 Zinc 062480 10 Threaded Insert M16 x 125 Stainless 051175 10
Threaded Insert M10 x 65 Stainless 062960 10 Threaded Insert M20 x 170 Zinc 062810 10
Threaded Insert M12 x 75 Zinc 062760 10
Threaded Inserts - Indicative Working Loads in 32 MPa Concrete with Structaset™ 401
Tightening Tightening
Thread Drilled Hole Min Hole Min Edge Min Anchor Max Tensile Max Shear
Torque (Nm) Torque (Nm)
Size Ø (mm) Depth (mm) Distance (mm) Spacing (mm) Load, Na (kN) Load, Vas (kN)*
5.8 A4 Bolt 8.8 Bolt
M8 14 65 10 15 65 120 7.3 5.4
M10 20 70 22 30 65 130 11.5 8.7
M12 24 75 36 70 85 150 16.7 12.5
M16 28 130 80 120 125 250 31.1 23.3
M20 35 175 120 200 170 340 50.4 36.3
Tension: Concrete = 2.1
Shear: Steel = 2.2

Hollow Brick & Block
Patented design ensures

adhesive is extruded where
it is needed most
Non-perforated tip
- no wasted adhesive
Hollow Brick and Block Anchoring

Accessories
Use with ChemSet™ 101 and Ultrafix™ Plus to anchor threaded studs into
hollow brick and block
• Forms a solid plug of adhesive in the brick or block cavity to provide
secure anchoring point
• Durable nylon sleeves ideal for 3 hole brick and hollow concrete block
• Fine Metal Mesh Sleeves ideal for 10 hole brick
Typical Properties
Nylon Sleeve Wire Mesh Sleeve
For Thread Overall Nominal Overall Nominal
Size Length (mm) Diameter Length (mm) Diameter
(mm) (mm)
M6 - - 1000 12.5 Features and Benefits
M8 64 12 1000 12.5 • Resistant to vibrating loads
M10 64 14 1000 15.0 • Corrosion resistant nylon
• No expansion stress on bricks
M12 64 16 1000 15.0
• Non-destructive installation
M16 - - 1000 20.5
• Easy, simple and quick to install
Substrates Wire Cut Extruded Clay Brick, Hollow Concrete Block
Related Products
DynaDrill™ Hole Cleaning Brushes
Carbide Drill Bits Hole Cleaning Pump
Diamond Motor UltraFix™ Plus
Diamond Core Drill Bits ChemSet™ 101

Hollow Brick & Block

Building Contractor Steel Fabricator Balustrade Contractor Fitter
Hand rails 4 4
Gate Hinges 4
Timber Beams 4

Steel Beams 4 4

Installation
1. Drill hole to specified diameter in brick or block using a masonry drill bit
2. Brush and blow dust out of holes
3. Cut wire mesh sleeves to length nominated in table below and fold or twist
one end to close it
4. Insert nylon or wire mesh sleeve into hole
5. Insert ChemSet 101 or Ultrafix™ Plus mixing nozzle into sleeve and
dispense adhesive, withdrawing nozzle as it fills
6. Insert threaded rod or stud into sleeve
7. Allow adhesive to cure before loading
Hollow Brick and Block Anchoring Accessories

Description To Suit Part Number Pack Quantity
Nylon Sleeve 12 mm Diameter M8 Thread ISS08 100
Fine Metal Mesh Sleeve12 x 1000 mm M8 Thread ISM08 1
Fine Metal Mesh Sleeve16 x 1000 mm M10 / M12 Thread ISM12 1
Fine Metal Mesh Sleeve 22 x 1000 mm M16 Thread ISM16 1
Indicative Working Loads in Hollow Brick/Block with ChemSet™ 101, Ultrafix™ Plus
& ChemSet™ Hollow Block Accessories
Installation details Working Load Limit (kN)
Anchor size, db Substrate Sleeve/Sieve Drilled hole Fixture hole Anchor Tightening Solid Brick
(mm) Type diameter, diameter, effective depth, torque, Tr
dh (mm) df (mm) h (mm) (Nm) Shear, Va Tension, Na
M8 10 10 80 10 4.4 1.4
M10 12 12 85 20 4.8 1.5
Solid Clay Brick –
M12 14 15 85 40 5.2 1.6
M16 18 19 85 95 5.2 1.7
Note: Use specified hole size for solid brick. Use of larger hole and/or sleeve/sieve will result in lower capacities.
Installation details Working Load Limit (kN)

Anchor Drilled hole diameter, dh Fixture hole Anchor Tightening 3 Hole Brick 10 Hole Brick Concrete Block
size, d Substrate

b (mm) diameter, effective depth, torque, Tr
(mm) Nylon Sleeve S/S Sieve df (mm) h (mm) (Nm) Shear, Va Tension, Na Shear, V a Tension, Na Shear, Va Tension, Na
M8 3 Hole Brick, 12 12 10 10 3.8 2.5 3.0 1.0 1.8 1.8

M10 10 Hole Brick 14 16 12 20 4.6 2.5 4.6 1.0 2.0 1.8
64
M12 or Concrete 16 16 15 40 5.0 2.5 5.0 1.0 2.0 1.8
Block
M16 – 22 19 95 5.0 2.5 5.0 1.0 2.0 1.8
The strength in tension of ChemSet™ fixings for hollow block exceeds the strength of hollow brick and concrete block. Therefore load capacity of the fixing is limited by the
strength of the brick or block. Over loading the fixing will risk destruction of the brick or block. Shear properties based on grade 4.6 carbon steel threaded rod.

Accessories
Chemical Anchoring
CUA
ChemSet™ Anchoring Accessories
Suits all ChemSet™

injection adhesives
Key Features CUAPN

• 5.25kN (525kgf) thrust at 6.8 bar
operating pressure
• Maximum air pressure inlet: 100psi
• Inlet: Max 150 litres/minute (5 cfm)
ChemSet™ Universal Applicator ChemSet™ Pneumatic Powered Applicator

Dispenses all of the products in the ChemSet Injection Range
™
Effortless dispensing of all products in the ChemSet™ Injection range
• Robust all-metal construction • Powered by compressed air
• Twin drive for powerful dispensing • Reduces fatigue when dispensing a large number of cartridges
Recommended ChemSet™ Cartridges Chemical

Pack Size Product Part Number Anchoring Kit
380ml ChemSet 101™ C101C, ISKP, ISKPT
380ml ChemSet 801™ C801C
750ml ChemSet 101™ C101J
750ml ChemSet 801™ C801J
750ml ChemSet Reo502™ RE0502J
Part No. CHEMKITBAG

Accessories
Chemical Anchoring
ChemSet™ Anchoring Accessories

HCPHV HCP
HCBT13, HCBT20, HCBT26
Hole Cleaning Accessories

Cleaning dust and debris from holes is necessary to obtain full adhesion and load capacity from Chemical Anchors.
• Ramset™ provides a full range of hole cleaning accessories to ensure the best results from Ramset™ Chemical Anchoring products
• To remove dust and debris after drilling
• Removing dust ensures rated load capacities are achieved

Hole Cleaning Pump (Blower) All hole sizes HCP 1
Hole Cleaning Pump (High Volume) All hole sizes HCPHV 1
Hole Cleaning Brush 13 mm 8 – 12 mm Diameter Holes HCBT13 1
Longer brushes for deep holes available on request.
Retaining Collars for Hollow Base Materials and Overhead Applications in Solid Materials
• Prevents drip in overhead installations
Description Part Number To Suit Pack Quantity

10mm Retaining Collar ISR10 CS10130 100
ISNP ISNE ISNET
Mixing Nozzles
Always use recommended mixing nozzles for each adhesive. Using the incorrect nozzle will result in improper mixing and poor load resistance.
Description Length Length with Extension

Epoxy Mixing Nozzles 255mm 440mm
Fast Dispensing Epoxy Nozzles - Turbo 440mm -
Polyester Mixing Nozzles 215mm -

Epoxy Mixing Nozzles C801C, C801J, REO502J, S401C ISNE 5
Fast Dispensing Epoxy Nozzles - Turbo C801C, C801J, REO502J ISNET 1
Polyester Mixing Nozzles C101C, C101J, ISKP, S401C ISNP 5
UFP300, UFP300P

Installation Guide
Chemical Anchoring
Solid Substrates
The following installation instructions are for ChemSet™ 101,
Structaset™ 401, ChemSet™ 801, ChemSet™ Reo 502™ and Ultrafix™ Plus 2. Clean hole with correctly sized cleaning
anchoring adhesives into solid concrete. brush with stiff nylon or wire bristles. Using a
combination Push/Pull and twisting (rotation)
motion, ensure the sides of the hole are
Precautions scrubbed at least 3 times for the full depth of
• For ease of use ensure the adhesive temperature is greater than the
the hole. (See page 107 for correct brush size)
minimum installation temperature listed on the pack.
• When substrate temperature is less than the minimum listed on the
pack, the adhesive may fail to cure. Satisfactory results may be obtained 3. Remove debris, dust etc. from the hole
Installation Guide
by first warming the cartridges, studs and / or rebar to about 20° to 25°C using a hole cleaning blower with at least 4
then warming the concrete with a blow torch or similar before injecting swift pumps, alternatively a strong blast of
the adhesive. (Do not use flame near adhesives) compressed air or wet/dry vacuum maybe
• In cold conditions, avoid applying excessive pressure to the dispensing used.
gun. Excessive pressure may damage the dispensing gun or result in
adhesive loss from the back of the cartridge.
4. Reinforcing bars, internally threaded sockets,
• Use only the correctly mixed adhesive – incorrect mix ratio will cause a
threaded rods or studs to be used should be
reduction in load capacity.
cleaned and free from oil, grease, flaking rust
• IMPORTANT - Always ensure hole is properly cleaned. Refer to cartridge
or debris. Threaded rods or studs should be
or product information to determine if suitable for wet holes.
chisel ended to prevent them unthreading
• Prevent exposure of ChemSet™ 801 to moisture or water for at least 24
from the cured adhesive.
hours after installation to allow for maximum curing.
• Do not dilute adhesive with any solvents and/or other chemicals.
• Always use the correct mixing nozzle listed on the pack. Other nozzles 5. If holes are not dry, consult product pack
may cause ineffective mixing and reduce the properties of the adhesive. to determine if adhesive is suitable for the
• Do not install into concrete less than 3 days old hole condition. If holes have been left for a
• Full load capacity will not be achieved in concrete less than 28 days old. prolonged period since drilling, re-cleaning
• Full load capacity will be achieved in concrete greater than 28 days old, in accordance with ‘2 & 3’ above is
even if installed earlier than 28 days recommended.
• Do not remove spiral mixer from nozzles.
• Do not cut or shorten nozzles.
• Roughen diamond core drilled holes prior to installing ChemSet™ 101 or 6. Remove nut from the cartridge and attach the
Ultrafix™ Plus correct Ramset mixing nozzle. Screw down
tight. (Ultrafix™ Plus cut plastic bag before
attaching mixing nozzle)
Installation Instructions:
Read the “Precautions” section of these instructions prior to use.
Read safety directions on the pack before opening or using. In general,
wear safety goggles, gloves and hearing protection when drilling and using
anchoring adhesive. 7. Mount assembled cartridge into the Ramset Universal Applicator (Mount
Setting and technical data provided applies to: Ultrafix™ Plus in regular caulking gun).
• Holes drilled with Rotary Hammers using drill bits toleranced in
accordance with DIN8035, and where holes have been cleaned using a 8. Open the orange valve (Not necessary for Ultrafix™ Plus). Turn so arrow
brush and air pump. points forward. Dispense adhesive to waste until an even, uniform
• Holes cored with diamond coring equipment that have been cleaned using colour is achieved. Approximately 2-3 trigger pulls should be adequate.
a brush and air pump or wet/dry vacuum. See pack or product information for correct colour. The initial flow is
• Always wear safety goggles. unsuitable for fastening and must not be used.
Solid Substrates
1. Drill hole using correctly sized rotary hammer

drill bit or diamond core bit to the specified
depth. (see cartridge label, product information
or engineering drawings)

Installation Guide
Chemical Anchoring
Overhead Installation in Solid Substrates

9. Insert mixer nozzle to the base of the The following installation instructions are for ChemSet™ 101, Structaset™
hole and inject. 401 and Ultrafix™ Plus anchoring adhesives into solid concrete.
10. To avoid creating air pockets, slowly
withdraw the nozzle as the hole fills with
each squeeze. Use an extension tube for For overhead installation into solid substrate,
deep holes. prepare hole and cartridge as per installation
instructions, solid substrate 1 to 8
See trigger pulls guide in this section to
estimate the required amount of adhesive to
just fill the hole with minimal waste.
Installation Guide
9. Insert correct retaining collar into hole,
see page 107.
11. Once the required fill

10. Slowly withdraw the nozzle as the hole
is obtained, release
fills with each trigger squeeze, while
pressure by pressing
continuing to hold retaining collar against
rear trigger. Close
substrate. Use an extension tube for deep
orange valve to preserve
holes.
contents.
11. Once the required fill is obtained release

pressure by pressing rear trigger and wipe off
the excess material.
12. Insert the stud, bar or socket into the hole
using a slow twisting motion to release
trapped air. Wipe away the excess
material from the concrete surface
around the fixing. 12. Still holding the retaining collar, push the stud
into the hole using a slow twisting motion.
Wipe away excess material.
13. Do not touch anchor until mixture has gelled

and do not load anchor until curing is
13. Load anchor when curing is complete. complete. See cartridge label or product
See cartridge label or product information information for curing times.
for curing times.
14. Attach fixture and tighten nut in accordance

with recommended tightening torque.
14. Attach fixture and tighten nut in

accordance with recommended
TRIGGER PULLS
tightening torque
ChemSet™ ChemSet™ ChemSet™
Stud Hole Dia. Hole Depth Carbide 101 801 Reo502™
Size (mm) (mm) Drill Bit 380 ml 750 ml 380 ml 750 ml 750 ml
M8 10 80 DDR310100 1 1 1 1 1
Refer to Technical Data Sheet and MSDS
M10 12 90 DDR312125 1 1 1 1 1
available from www.ramset.com.au, M12 14 110 DDR314200 1.5 1.5 1.5 1.5 1.5
for precautions and further detailed M16 18 125 DQR318200 2.5 2 2 2 2
installation instructions M20 24 150 DYSM24200 6 5 6 5 5
M24 26 160 DYSM26250 6 5 6 5 5

Installation Guide
Chemical Anchoring
Hollow Block, Hollow Brick and Hollow Core Panels
The following installation instructions are

for ChemSet™ 101, Structaset™ 401 and
Ultrafix™ Plus anchoring adhesives into
hollow pre-manufactured masonry units.
Fixing positions Hollow Block

Installation Guide
1. One fixing per block cavity only.

2. Minimum edge distance - ½ block
Correct installation Incorect installation - not recommended
Do not fix in orange areas
Fixing positions Hollow Brick
Correct installation
Performance will be significantly reduced Incorect installation - not recommended
1. Only one fixing recommended per brick.

2. Minimum edge distance – 1 brick
Refer to Technical Data Sheet and MSDS

available from www.ramset.com.au,
Do not fix in orange areas for precautions and further detailed

Installation Guide
Chemical Anchoring
Installation Instructions:
Read the “Precautions” section of these instructions prior to use, see page 108.
Setting and technical data provided applies to:
• Holes drilled with Rotary Hammers using drill bits toleranced in accordance with DIN8035, and where
holes have been cleaned using a brush and air pump.
• Always wear safety goggles.
1. Drill hole using correctly sized drill bit through wall of hollow block or brick, see pack or product information
Installation Guide
2. Clean hole with correctly sized hole cleaning brush with stiff nylon or wire bristles. Using a combination Push/
Pull and twisting (rotation) motion, ensure the sides of the hole are scrubbed at least 3 times for the full depth
of the hole.
3. Hollow block studs, threaded studs or threaded rod to be used should be cleaned and free from oil,
grease, flaking rust or debris.
4. Insert correct sleeve or sieve into hole, see page 105.
5. Remove nut from the cartridge and attach the correct Ramset mixing nozzle screw down tight.
(Ultrafix™ Plus pull out and cut plastic bag)
6. Mount assembled cartridge into the Ramset Universal Applicator (Mount Ultrafix™ Plus in regular
caulking gun).
7. Open the orange valve (Not necessary for Ultrafix™ Plus). Turn so arrow points forward. Dispense adhesive to
waste until an even, uniform colour is achieved. Approximately 2-3 trigger pulls should be adequate. See pack
or product information for correct colour. The initial flow is unsuitable for fastening and must not be used.
8. Inject adhesive until the sleeve/sieve is filled to ¾ of depth, slowly withdraw nozzle and complete filling.
9. Once the required fill is obtained release the pressure by pressing rear trigger and wipe off excess material.
10. Push the stud into the hole using a slow twisting motion. Wipe away excess material.
11. Do not touch anchor until mixture has gelled and do not load anchor until curing is complete
12. Attach fixture and tighten nut in accordance with recommended tightening torque.

Estimating Charts
Chemical Anchoring
Quantity of 750ml (Jumbo) Cartridges For Reinforcing Bar Anchoring
Number of N10 Bars

20 30 40 50 60 70 80 90 100 125 150 175 200
Hole Diameter (mm) Hole Depth (mm) Number of 750 ml cartridges for various quantities of N10 bars
60 1 1 1 1 1 1 1 1 1 1 1 2 2
70 1 1 1 1 1 1 1 1 1 1 2 2 2
90 1 1 1 1 1 1 1 1 1 2 2 2 2
100 1 1 1 1 1 1 1 1 2 2 2 2 3
Estimating Charts
110 1 1 1 1 1 1 1 2 2 2 2 2 3
120 1 1 1 1 1 1 1 2 2 2 2 3 3
140 1 1 1 1 1 2 2 2 2 2 3 3 3
14 150 1 1 1 1 1 2 2 2 2 2 3 3 4
160 1 1 1 1 1 2 2 2 2 3 3 3 4
180 1 1 1 1 2 2 2 2 2 3 3 4 4
230 1 1 1 2 2 2 2 3 3 3 4 5 5
255 1 1 2 2 2 2 3 3 3 4 4 5 6
275 1 1 2 2 2 2 3 3 3 4 5 5 6
300 1 1 2 2 2 3 3 3 4 4 5 6 7
400 1 2 2 3 3 3 4 4 5 6 7 8 9
Number of N12 Bars

20 30 40 50 60 70 80 90 100 125 150 175 200
70 1 1 1 1 1 1 1 1 1 2 2 2 2
80 1 1 1 1 1 1 1 1 1 2 2 2 2
90 1 1 1 1 1 1 1 1 2 2 2 2 3
100 1 1 1 1 1 1 1 2 2 2 2 3 3
110 1 1 1 1 1 1 2 2 2 2 2 3 3
125 1 1 1 1 1 2 2 2 2 2 3 3 4
150 1 1 1 1 2 2 2 2 2 3 3 4 4
16 200 1 1 1 2 2 2 2 3 3 4 4 5 5
210 1 1 2 2 2 2 3 3 3 4 4 5 6
235 1 1 2 2 2 2 3 3 3 4 5 5 6
250 1 1 2 2 2 3 3 3 4 4 5 6 7
270 1 1 2 2 2 3 3 3 4 5 5 6 7
310 1 2 2 2 3 3 3 4 4 5 6 7 8
335 1 2 2 3 3 3 4 4 5 6 7 8 9
400 1 2 2 3 3 4 4 5 5 7 8 9 10
500 2 2 3 4 4 5 5 6 7 8 10 11 13
Number of N16 Bars

20 30 40 50 60 70 80 90 100 125 150 175 200
100 1 1 1 1 1 2 2 2 2 2 3 3 4
125 1 1 1 1 2 2 2 2 2 3 3 4 4
150 1 1 1 2 2 2 2 3 3 3 4 5 5
175 1 1 2 2 2 2 3 3 3 4 5 5 6
200 1 1 2 2 2 3 3 3 4 4 5 6 7
20 225 1 2 2 2 3 3 3 4 4 5 6 7 7
250 1 2 2 2 3 3 4 4 4 5 6 7 8
270 1 2 2 3 3 3 4 4 5 6 7 8 9
350 2 2 3 3 4 4 5 5 6 7 9 10 11
450 2 3 3 4 5 5 6 7 7 9 11 13 14
495 2 3 4 4 5 6 7 7 8 10 12 14 16
600 2 3 4 5 6 7 8 9 10 12 14 17 19
Number of 380ml cartridges is approximately double 750ml quantity. Number of N20 Bars
Tables assume no waste other than amount contained
20 30 in
40 mixing
50 nozzle.
60 70 80 90 100 125 150 175 200
125 1 1 2 2 2 3 3 3 4 4 5 6 7
150 1 2 2 2 3 3 3 4 4 5 6 7 8
112 www.ramset.com.au
170 1300 780
1 063
2 2 3 3 3 4 4 5 6 7 8 9
200 1 2 2 3 3 4 4 5 5 7 8 9 10
125 1 1 1 1 2 2 2 2 2 3 3 4 4
150 1 1 1 2 2 2 2 3 3 3 4 5 5
175 1 1 2 2 2 2 3 3 3 4 5 5 6
20
200
225
250
1
1
1
1
2
2
2
2
2
2
2
2
2
3
3
3
3
3
3
3
4
Estimating Charts
3
4
4
4
4
4
4
5
5
5
6
6
6
7
7
7
7
8
270 1 2 2 3 3 3 4 4 5 Chemical Anchoring
6 7 8 9
350 2 2 3 3 4 4 5 5 6 7 9 10 11
450 2 3 3 4 5 5 6 7 7 9 11 13 14
495 2 3 4 4 5 6 7 7 8 10 12 14 16
600 2 3 4 5 6 7 8 9 10 12 14 17 19
Number of N20 Bars

20 30 40 50 60 70 80 90 100 125 150 175 200
125 1 1 2 2 2 3 3 3 4 4 5 6 7
150 1 2 2 2 3 3 3 4 4 5 6 7 8
170 1 2 2 3 3 3 4 4 5 6 7 8 9
200 1 2 2 3 3 4 4 5 5 7 8 9 10
Estimating Charts
225 2 2 3 3 4 4 5 5 6 7 9 10 11
250 2 2 3 4 4 5 5 6 7 8 10 11 13
25 275 2 2 3 4 4 5 6 6 7 9 10 12 14
300 2 3 3 4 5 6 6 7 8 10 11 13 15
350 2 3 4 5 6 6 7 8 9 11 13 15 17
455 3 4 5 6 7 8 9 10 12 14 17 20 23
500 3 4 5 7 8 9 10 11 13 16 19 22 25
585 3 5 6 8 9 10 12 13 15 18 22 25 29
635 4 5 7 8 10 11 13 14 16 20 24 27 31
700 4 6 7 9 11 12 14 16 17 22 26 30 34
Number of N24 Bars

10 20 30 40 50 60 70 80 90 125 150 175 200
150 1 2 2 3 3 4 4 5 5 7 8 10 11
175 1 2 2 3 4 4 5 5 6 8 10 11 13
210 1 2 3 3 4 5 6 6 7 10 11 13 15
225 1 2 3 4 4 5 6 7 8 10 12 14 16
250 1 2 3 4 5 6 7 7 8 11 14 16 18
275 1 2 3 4 5 6 7 8 9 13 15 17 20
300 2 3 4 5 6 7 8 9 10 14 16 19 21
30 320 2 3 4 5 6 7 8 9 11 14 17 20 23
335 2 3 4 5 6 8 9 10 11 15 18 21 24
400 2 3 5 6 7 9 10 12 13 18 21 25 28
480 2 4 6 7 9 11 12 14 16 21 26 30 34
565 2 4 6 8 10 12 14 16 18 25 30 35 40
740 3 6 8 11 13 16 19 21 24 33 39 46 52
805 3 6 9 12 15 17 20 23 26 36 43 50 57
900 4 7 10 13 16 19 22 26 29 40 48 55 63
Number of N28 Bars

10 20 30 40 50 60 70 80 90 125 150 175 200
170 1 2 3 4 5 5 6 7 8 11 13 15 17
200 1 2 3 4 5 6 7 8 9 12 15 17 19
225 2 3 4 5 6 7 8 9 10 14 17 19 22
250 2 3 4 5 6 8 9 10 11 15 18 21 24
270 2 3 4 6 7 8 9 11 12 17 20 23 26
300 2 3 5 6 8 9 10 12 13 18 22 25 29
325 2 4 5 7 8 10 11 13 14 20 24 27 31
35 350 2 4 5 7 9 10 12 14 15 21 25 30 34
400 2 4 6 8 10 12 14 16 18 24 29 34 38
500 3 5 8 10 12 15 17 19 22 30 36 42 48
680 4 7 10 13 17 20 23 26 30 41 49 57 65
780 4 8 12 15 19 23 26 30 34 47 56 65 74
880 5 9 13 17 21 26 30 34 38 53 63 74 84
960 5 10 14 19 23 28 32 37 41 57 69 80 92
1050 5 10 15 20 25 30 35 40 45 63 75 88 100
Number of 380ml cartridges is approximately double 750ml quantity.

Tables assume no waste other than amount contained in mixing nozzle. Number of N32 Bars
5 10 15 20 25 30 50 70 90 125 150 175 200
210 1 2 2 3 4 4 7 10 12 17 20 23 27
250 1 2 3 4 4 5 www.ramset.com.au
8 11 14 201300 780
24 063 28 32 113
275 1 2 3 4 5 6 9 12 16 22 26 30 35
300 2 3 5 6 8 9 10 12 13 18 22 25 29
325 2 4 5 7 8 10 11 13 14 20 24 27 31
35
Estimating Charts
350 2 4 5 7 9 10 12 14 15 21 25 30 34
400 2 4 6 8 10 12 14 16 18 24 29 34 38
500 3 5 8 10 12 15 17 19 22 30 36 42 48
Chemical Anchoring 680

780
4
4
7
8
10
12
13
15
17
19
20
23
23
26
26
30
30
34
41
47
49
56
57
65
65
74
880 5 9 13 17 21 26 30 34 38 53 63 74 84
960 5 10 14 19 23 28 32 37 41 57 69 80 92
1050 5 10 15 20 25 30 35 40 45 63 75 88 100
Number of N32 Bars
5 10 15 20 25 30 50 70 90 125 150 175 200
210 1 2 2 3 4 4 7 10 12 17 20 23 27
250 1 2 3 4 4 5 8 11 14 20 24 28 32
275 1 2 3 4 5 6 9 12 16 22 26 30 35
300 1 2 3 4 5 6 10 14 17 24 28 33 38
325 2 3 4 5 6 7 11 15 19 26 31 36 41
Estimating Charts
350 2 3 4 5 6 7 11 16 20 28 33 38 44
375 2 3 4 5 6 7 12 17 21 30 35 41 47
40 390 2 3 4 5 7 8 13 17 22 31 37 43 49
450 2 3 5 6 7 9 14 20 26 35 42 49 56
550 2 4 6 7 9 11 18 24 31 43 52 60 69
680 3 5 7 9 11 13 22 30 38 53 64 74 85
800 3 5 8 10 13 15 25 35 45 63 75 87 100
1035 4 7 10 13 17 20 33 45 58 81 97 113 129
1130 4 8 11 15 18 22 36 50 64 88 106 123 141
1250 4 8 12 16 20 24 39 55 70 97 117 136 156
Number of N36 Bars

5 10 15 20 25 30 50 70 90 125 150 175 200
225 1 2 3 4 5 6 9 13 16 22 27 31 36
250 1 2 3 4 5 6 10 14 18 25 30 35 40
275 2 3 4 5 6 7 11 16 20 27 33 38 43
300 2 3 4 5 6 8 12 17 22 30 36 42 47
330 2 3 4 6 7 8 13 19 24 33 39 46 52
375 2 3 5 6 8 9 15 21 27 37 44 52 59
400 2 4 5 7 8 10 16 22 29 40 47 55 63
45 425 2 4 5 7 9 10 17 24 30 42 50 59 67
430 2 4 6 7 9 11 17 24 31 43 51 59 68
550 3 5 7 9 11 13 22 31 39 54 65 76 86
650 3 6 8 11 13 16 26 36 46 64 77 89 102
800 4 7 10 13 16 19 32 44 57 79 94 110 126
920 4 8 11 15 18 22 36 51 65 90 108 126 144
1190 5 10 14 19 24 28 47 66 84 117 140 163 186
1300 6 11 16 21 26 31 51 72 92 127 153 178 204
1400 6 11 17 22 28 33 55 77 99 137 165 192 219
Number of N40 Bars

4 6 8 10 25 30 50 70 90 125 150 175 200
225 1 2 2 3 6 7 11 16 20 28 33 38 44
250 1 2 2 3 7 8 13 17 22 31 37 43 49
275 2 2 3 3 7 8 14 19 24 34 40 47 54
300 2 2 3 3 8 9 15 21 27 37 44 51 58
360 2 3 3 4 9 11 18 25 32 44 53 61 70
400 2 3 4 4 10 12 20 27 35 49 58 68 78
425 2 3 4 5 11 13 21 29 37 52 62 72 82
50 450 2 3 4 5 11 14 22 31 40 55 66 76 87
500 2 3 4 5 13 15 25 34 44 61 73 85 97
650 3 4 6 7 16 19 32 44 57 79 94 110 126
800 4 5 7 8 20 24 39 54 70 97 116 135 155
950 4 6 8 10 23 28 46 65 83 115 138 161 184
1045 5 7 9 11 26 31 51 71 91 126 152 177 202
1355 6 8 11 14 33 40 66 92 118 164 196 229 262
1475 6 9 12 15 36 43 72 100 128 178 214 249 285
1550 6 9 12 15 38 45 75 105 135 187 225 262 299
Number of 380ml cartridges is approximately double 750ml quantity.

Tables assume no waste other than amount contained in mixing nozzle.
Estimating Charts
Chemical Anchoring
Quantity of Cartridges for ChemSet™ 101 and Structaset™ 401 with ChemSet™ Anchor Studs
at Standard Embedment Depths
Number of Cartridges for ChemsetTM 101 with ChemsetTM Anchor Studs at Standard Embedment Depths
Stud Size Cartridge Number of Fixings
x Depth Size 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200 210 220 230 240 250
M8 750 ml 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2
Number
80 mm 380 ml
of Cartridges 1 TM 101
for Chemset 1 with1 Chemset
1 TM1Anchor 1 Studs
1 1at Standard
1 2 Embedment
2 2 Depths2 2 2 2 2 2 2 3 3 3 3 3 3
M10
Stud Size 750 ml
Cartridge 1 1 1 1 1 1 1 1 1 1 1 1
Number 1 of Fixings
2 2 2 2 2 2 2 2 2 2 2 2
x 90 mm
Depth 380
Sizeml 1
10 1 30
20 1 40 1 50 1 60 1 70
2 802 90
2 100 2 110 2 120 2 130 2 140 3 150 3 160 3 170 3 180 3 3
190 4
200 4
210 4 230
220 4 4
240 4
250
M12
M8 750 ml 1 1 1 1 1 1 1 1 12 12 12 12 12 12 12 12 12 13 13 23 23 23 23 23 23
Estimating Charts
110 mm
80 mm 380 ml 1 1 1 1 12 12 12 12 13 23 23 23 24 24 24 24 24 25 25 35 35 36 36 36 36
M16
M10 750 ml 1 1 1 1 1 12 12 12 12 12 12 13 13 23 23 23 24 24 24 24 24 24 25 25 25
125 mm
90 mm 380 ml 1 1 12 12 12 13 23 23 24 24 25 25 25 36 36 36 37 37 37 48 48 49 49 49 10
4
M20
M12 750 ml 1 1 12 12 13 13 14 14 25 25 25 26 26 27 27 28 28 39 39 39 103 103 113 11
3 12
3
150 mm
110 380 ml 1 12 13 14 25 26 27 28 39 10 3 113 11 3 124 13 4 14 4 154 164 175 185 195 205 216 216 226 23
6
M24
M16 750 ml 1 1 12 12 13 23 23 24 24 25 25 36 36 36 37 37 48 48 48 49 49 104 105 115 11
5
160 mm
125 380 ml 1 12 23 24 25 36 36 37 48 49 10 5 11 5 11 5 12 6 13 6 14 6 15 7 16 7 17 7 17 8 188 199 209 219 22
10
M20 750 ml 1 1 2 2 3 3 4 4 5 5 5 6 6 7 7 8 8 9 9 9 10 10 11 11 12
150 mm 380 ml 1 TM 2 3 4 TM 5 6 7 8 9 TM10 11 11 12 13 14 15 16 17 18 19 20 21 21 22 23
Number of cartridges for Chemset 801 and Chemset Reo 502 with Chemset Anchor Studs at Standard Embedment Depths
M24 750 ml 1 1 2 2 3 3 3 4 4 5 5 6 6 6 7 7 8 8 8 9 9 10 10 11 11
Quantity of cartridges for ChemSet 801 and ChemSet Reo 502 with ChemSet Anchor
Stud
160 Size
mm
x Depth
Cartridge
380 ml
Size
1
10
2 3 4 5 6 6 ™7 8 9 10 Number
11
20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180
11ofofFixings
Number Fixings
12 ™ 13 14 15™ 16 17
190
17
200
18
210
19™ 20
220 230
21
240
22
250
Studs at Standard Embedment Depths
M8
80 mm
Number
750 ml
of cartridges
380 ml
1 1 1 1
1 TM 8011 and 1Chemset
for Chemset
1 1 1 1 1
1 TM Reo
1 502 1 with
1 Chemset
1 1 1 1
1 1 TM 2Anchor2 Studs2 at Standard
2
1 1
2Embedment
2
1 1
2 Depths
2
1
2
1
3
2
3
2
3
2
3
2
3
2
3
2
3
M10
Stud Size 750 ml
Cartridge 1 1 1 1 1 1 1 1 1 1 1 1Number
Number 1 ofofFixings
2
Fixings 2 2 2 2 2 2 2 2 2 2 2
x 90 mm
Depth 380
Sizeml 1
10 1 30
20 1 40 1 50 1 60 1 70
2 802 90
2 100 2 110 2 120 2 130 3 140 3 150 3 160 3 170 3 180 3 4
190 4
200 4
210 4 230
220 4 4
240 5
250
M12
M8 750 ml 1 1 1 1 1 1 1 1 2
1 1 2 1 2 1 2 1 2 1 2 1 2 1 2 1 2 1 3 13 23 23 23 23 23 23
110 mm
80 mm 380 ml 1 1 1 1 12 12 12 12 13 23 23 23 24 24 24 24 25 25 35 35 36 36 36 36 37
M16
M10 750 ml 1 1 1 1 1 12 12 12 12 12 13 13 13 23 23 23 24 24 24 24 24 25 25 25 25
125 mm
90 mm 380 ml 1 1 12 12 12 13 23 24 24 24 25 25 36 36 36 37 37 38 48 48 49 49 49 10
4 10
5
M20
M12 750 ml 1 1 12 12 13 13 14 14 25 25 26 26 26 27 27 28 28 39 39 103 103 113 113 11
3 12
3
150
110 mm 380 ml 1 12 13 14 25 26 27 28 39 10 3 113 12 3 134 14 4 15 4 164 175 185 195 205 216 226 236 246 25
7
M24
M16 750 ml 1 1 12 12 13 23 23 24 24 25 35 36 36 36 37 37 48 48 49 49 49 105 105 115 11
5
160
125 mm 380 ml 1 12 23 24 25 36 37 48 49 49 10 5 11 5 12 6 13 6 14 6 15 7 16 7 17 8 18 8 18 8 199 209 219 22
10 23
10
M20 750 ml 1 1 2 2 3 3 4 4 5 5 6 6 6 7 7 8 8 9 9 10 10 11 11 11 12
150 mm 380 ml 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
M24 750 ml 1 1 2 2 3 3 3 4 4 5 5 6 6 6 7 7 8 8 9 9 9 10 10 11 11
160 mm 380 ml 1 2 3 4 5 6 7 8 9 9 10 11 12 13 14 15 16 17 18 18 19 20 21 22 23
Quantity of Structaset™ 401 380ml Cartridges with Threaded Inserts

Thread Drill
Number of Fixings
Depth
Size (mm) 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200 210 220 230 240 250
M8 65 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 3 3 3 3 3 3 3 3 4
M10 70 1 1 1 2 2 2 3 3 3 4 4 4 5 5 5 6 6 6 7 7 7 8 8 8 9
M12 80 1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 9 10 10 10 11 11 12 12
M16 130 2 3 4 5 7 8 9 10 12 13 14 15 17 18 19 20 22 23 24 25 27 28 29 30 32
M20 175 3 5 8 10 13 15 18 20 23 25 28 30 33 35 38 40 43 45 48 50 53 55 58 60 63
Tables assume no waste other than amount contained in mixing nozzle.

Construction
Chemicals
Welcome to the range of Ramset™ Construction

Chemicals products. Ramset™ supply a quality
range of popular construction Sealants, Adhesives,
Grouts, Expanding Foams and Concrete additives for
all building trades.
Ramset™ keep up to date with the latest

environmental, health and safety trends, including
Green Star, and provide VOC certificates for all
Construction Chemical products. Ramset™
specialise in Fire Rated products and provide
extensive fire rated sealant design information to
assist compliance with increasingly stringent fire
rating standards.
In summary, Ramset™ Construction Chemical

products can be used with confidence that they
comply with building standards, health and safety
regulations, resulting in speedier inspections and
sign off.

Construction
Chemicals

Contents
Construction Chemicals
Sealant Estimating Charts 120

Joint Design Guide 121
Selection Guide 122
Grout Estimating Charts 123

Sealants 124
• BlazeBrake™ Sealant – Fire Rated Acrylic
• FyreBrake™ Sealant – Fire Rated Polyurethane
• Gap Seal – Paintable Acrylic Gap Sealant
• Duct Seal – Sheet Metal Duct Sealant
• DynaSeal™ – Acrylic Construction Sealant
• HiSeal™ – Polyurethane Construction Sealant
• Water Seal – Sanitary Grade Construction Sealant
• Roof Seal – Neutral Cure Construction Sealant
Adhesives 134
• NailFree™ – Construction Adhesive
• Safe-T-Bond™ – Construction Adhesive
Self-Expanding Foams 136

• BlazeBrake™ Foam – Fire Rated Self-Expanding Polyurethane
• FomoFill™ – Straw Applied Self-Expanding Polyurethane Foam
• FomoPlus™ – Gun Applied Self-Expanading Polyurethane Foam
Additives 140
• Cemcrete – Polymer Bonding & Sealing Agent
™
• Concrebond™ - Acrylic Bonding & Sealing Agent
Grouts 142
• Premier Grout MP™ – Class A Non-Shrink Cement Grout
• Epoxy Grout – 2 Part Grouting Epoxy
Concrete Patch & Repair 146

• Epoxy Patch – 2 Part Bonding & Patching Agent
• Epoxy Putty – 2 Part Repair Putty
• Ultrafix™ Concremate™ - Non-Shrink Patching Cement
Accessories 150
Sealant Estimating
Charts
Sealant Estimating Chart

Lineal Metres per 960 g (600m ml) Sachet (Approx)
Joint Nominal Joint Width (mm)

Depth (mm) 6 8 10 12 15 20 25 50
6 16.6 -- -- -- -- -- -- --
Sealant Estimating Charts
8 x 9.4 -- -- -- -- -- --
10 x x 6.0 5.0 4.0 3.0 - -
12.5 x x x x x x 1.9 --
25 x x x x x x x 0.5
Lineal Metres per 450 g (300m ml) Cartridge (Approx)

Joint Nominal Joint Width (mm)
Depth (mm) 6 8 10 12 15 20 25 50
6 8.3 -- -- -- -- -- -- --
8 x 4.7 -- -- -- -- -- --
10 x x 3.0 2.5 2.0 1.5 -- --
12.5 x x x x x x 1.0 --
25 x x x x x x x 0.3
Coverage based on nominal dimensions

"--" Shallow joint. Risk of sealant tearing. Make joint deeper.
"x" Joint depth > width. Risk of sealant tearing. Adjust depth with backing rod.
Refer next page for correct joint design details.
Quantity of 300 ml cartridges required

Lineal Metres
Joint Joint
Width Depth 1 5 10 20 30 40 50 75 100
(mm) (mm)
6 6 1 1 2 3 4 5 6 9 12
8 8 1 2 3 5 7 9 11 16 22
10 10 1 2 4 7 10 14 17 25 34
12 10 1 2 4 8 12 16 20 30 40
15 10 1 3 5 10 15 20 25 38 50
20 10 1 4 7 14 20 27 34 50 67
25 12.5 2 6 11 21 32 42 53 79 105
50 25 5 21 42 84 125 167 209 313 417
Quantity of 600 ml sausages required

Lineal Metres
Joint Joint
Width Depth 1 5 10 20 30 40 50 75 100
(mm) (mm)
6 6 1 1 1 2 2 3 3 5 6
8 8 1 1 2 3 4 5 6 8 11
10 10 1 1 2 4 5 7 9 13 17
12 10 1 1 2 4 6 8 10 15 20
15 10 1 2 3 5 8 10 13 19 25
20 10 1 2 4 7 10 14 17 25 34
25 12.5 1 3 6 11 16 21 27 40 53
50 25 3 11 21 42 63 84 105 157 209

Joint Design
Guide
Joint Configuration & Design

Configuring joints in concrete structures for optimum sealant performance
General Details Sealant Description Strain Capacity
Movement of joints in concrete structures is caused by: HiSeal™ 1-Part Polyurethane Construction Sealant ± 25%
• Changes in Temperature (Opening and Closing)
FyreBrake™ 1-Part Polyurethane Fire Rated Sealant ± 25%
• Concrete Shrinkage (Opening)
Roof Seal 1-Part Neutral Cure Silicone Roofing Sealant ± 25%
• Concrete Creep (Closing)
The factors that cause joints to open are the most significant Joint Seal 1-Part Neutral Cure Silicone Construction Sealant ± 25%
Joint Design Guide

when optimising joint design for sealants. Glass Seal 1-Part Acetic Cure Silicone Glazing Sealant ± 25%
Because joints move, sealants must be elastic and flexible Water Seal 1-Part Acetic Cure Silicone Mould Resistant Sealant ± 25%
to avoid splitting, tearing and loss of adhesion. BlazeBrake™ 1-Part Fire and Acoustic Rated Acrylic Sealant ± 15%
A sealant’s flexibility is defined by its strain capacity, DynaSeal™ 1-Part Urethane-Acrylic Construction Sealant ± 20%
expressed as a percentage change in nominal joint width. Gap Seal 1-Part Acrylic Painters Sealant ± 6%
Joint Configuration Correct Width to Depth Ratio

The shape of the sealant within a joint influences its ability to stretch Joint Width Joint Depth
with movement. 6mm to 10mm Equal to joint Width
10mm to 20mm 10mm
20mm to 50mm Equal to 1/2 joint Width
Correct Joint Configuration

Chamfered Concrete
Control Joint in Concrete Floor
Edges Prevent Damage
(Concrete Panel)
Width greater than depth

plus concave finish allows
sealant to behave like
elastic band
Non-adherent, closed Floor meets Wall

cell backing rod to
Joint Between Precast control depth and
Concrete Panels prevent three-sided
adhesion
Incorrect Joint Configuration

Square concrete edges
prone to damage
(Concrete Panel) Control Joint in
Concrete Floor
Joint Poor Geometry. Block

Between shape resistant to stretching No Backing Rod. Stress
Precast Concentrates in narrow Joint
Concrete Open Cell or Adherent
Panels Depth greater than Backing Material –
width resists stretching Three-Sided Adhesion
Floor meets Wall
Each of the “Incorrect” cases listed here cause stress

concentrations within the sealant resulting in splitting or
tearing, or at interfaces resulting loss of adhesion.

Selection Guide
Sealant and adhesive selector guide

Product Recommended Substrates Properties
Polystyrene Foam
Galvanised Steel
Water Resistant
Water Clean Up
Heat Resistant
Chemical Type
Particle Board
Cement Sheet
Plasterboard
Exterior Use
Aluminium
Immersion
Fire Rated
Paintable
Low VOC
Concrete
Flexible
Timber
Joint Glass
Steel
Brick
MDF
Sealants
Selection Guide
BlazeBrake™ 4 4 4 4 4 4 Yes Yes Yes Yes Yes SC* Acrylic

BlazeBrake ™
4 4 4 4 4 4 4 4 4 4 4 4 Yes Yes Yes SC* Polyurethane
Foam
Duct Seal™ 4 4 Yes Yes Yes Acrylic
DynaSeal ™
4 4 4 4 4 4 4 4 Yes Yes Yes Yes SC* Acrylic
FomoFill ™
4 4 4 4 4 4 4 4 4 4 4 4 Yes Yes SC* Polyurethane
FomoPlus ™
4 4 4 4 4 4 4 4 4 4 4 4 Yes Yes SC* Polyurethane
FyreBrake ™
4 4 4 4 4 4 4 4 Yes Yes Yes Yes Yes Yes Polyurethane
Gap Seal 4 4 4 4 4 4 4 Yes Yes Yes Acrylic
HiSeal™ 4 4 4 4 4 4 4 4 4 4 4 Yes Yes Yes Yes Yes Polyurethane
Roof Seal 4 4 4 4 4 4 4 4 4 Yes Yes Yes Yes Yes Yes Silicone
Water Seal 4 4 4 4 Yes Yes Yes Yes Yes Yes Silicone
Adhesives
Synthetic
Nail Free™ 4 4 4 4 4 4 4 4 4 4 Yes Yes Yes
Rubber
Safe T Bond™ 4 4 4 4 4 4 4 4 4 Yes Yes Yes Acrylic
*SC = Special conditions; see product page for more details

Grout and concrete repair selector guide

Exterior Chemical
Product Grouting Patching Repair Bonding Sealing Cavity Fill Low VOC
Use Type
Premier
4 4 Yes Yes Cement
Grout MP™
Epoxy Grout 4 4 Yes Yes Epoxy
UltraFix
™
4 4 4 Yes Yes Cement
Concremate™
Epoxy Patch 4 4 4 4 4 Yes Yes Epoxy
Epoxy Putty 4 4 4 4 Yes Yes Epoxy
Cemcrete ™
4 4 4 Yes Yes Resin
Concrebond ™
4 4 4 Yes Yes Acrylic

Grout Estimating
Charts
Estimating chart for grouting in hollow sections into core drilled holes for posts, bollards etc
Litres of Grout for Core Drilled Holes in Concrete
Core Diameter Hole Depth (mm)
(mm) 100 140 160 180 190 200 210 220 230 240 250 260 270 280 290 300
66 0.4 0.5 0.6 0.7 0.7 0.7 0.8 0.8 0.8 0.9 0.9 0.9 1.0 1.0 1.0 1.1
76 0.5 0.7 0.8 0.9 0.9 1.0 1.0 1.0 1.1 1.1 1.2 1.2 1.3 1.3 1.4 1.4
Grout Estimating Charts

82 0.6 0.8 0.9 1.0 1.1 1.1 1.2 1.2 1.3 1.3 1.4 1.4 1.5 1.5 1.6 1.6
91 0.7 1.0 1.1 1.2 1.3 1.4 1.4 1.5 1.5 1.6 1.7 1.7 1.8 1.9 1.9 2.0
101 0.9 1.2 1.3 1.5 1.6 1.7 1.7 1.8 1.9 2.0 2.1 2.1 2.2 2.3 2.4 2.5
116 1.1 1.5 1.7 2.0 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.9 3.0 3.1 3.2
126 1.3 1.8 2.0 2.3 2.4 2.5 2.7 2.8 2.9 3.0 3.2 3.3 3.4 3.5 3.7 3.8
131 1.4 1.9 2.2 2.5 2.6 2.7 2.9 3.0 3.1 3.3 3.4 3.6 3.7 3.8 4.0 4.1
151 1.8 2.6 2.9 3.3 3.5 3.6 3.8 4.0 4.2 4.3 4.5 4.7 4.9 5.1 5.2 5.4
Estimating chart for grouting into cavities for underpinning

Litres of Grout Required for Rectangular Cavities
Width Length Hole Depth (mm)
(mm) (mm) 150 160 170 180 190 200 220 240 260 280 300 320 340 360 380 400
100 1000 15 16 17 18 19 20 22 24 26 28 30 32 34 36 38 40
200 1000 30 32 34 36 38 40 44 48 52 56 60 64 68 72 76 80
300 1000 45 48 51 54 57 60 66 72 78 84 90 96 102 108 114 120
400 1000 60 64 68 72 76 80 88 96 104 112 120 128 136 144 152 160
500 1000 75 80 85 90 95 100 110 120 130 140 150 160 170 180 190 200
600 1000 90 96 102 108 114 120 132 144 156 168 180 192 204 216 228 240
700 1000 105 112 119 126 133 140 154 168 182 196 210 224 238 252 266 280
800 1000 120 128 136 144 152 160 176 192 208 224 240 256 272 288 304 320
900 1000 135 144 153 162 171 180 198 216 234 252 270 288 306 324 342 360
Estimating chart for grouting in square solid or capped hollow sections into core drilled holes for
posts, bollards etc
Litres of Grout for Core Drilled Holes in Concrete
Core Hole Depth (mm)
Post
Diameter 100 140 160 180 190 200 210 220 230 240 250 260 270 280 290 300
(mm)
(mm)
66 50 0.1 0.2 0.2 0.2 0.2 0.2 0.2 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3 0.3
76 50 0.3 0.3 0.4 0.4 0.4 0.5 0.5 0.5 0.5 0.5 0.6 0.6 0.6 0.6 0.6 0.7
82 50 0.3 0.4 0.5 0.6 0.6 0.6 0.6 0.7 0.7 0.7 0.7 0.8 0.8 0.8 0.9 0.9
91 50 0.5 0.6 0.7 0.8 0.8 0.9 0.9 0.9 1.0 1.0 1.1 1.1 1.1 1.2 1.2 1.3
101 50 0.6 0.8 0.9 1.0 1.1 1.2 1.2 1.3 1.3 1.4 1.4 1.5 1.5 1.6 1.6 1.7
116 100 0.1 0.1 0.1 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2 0.2
126 100 0.3 0.4 0.4 0.5 0.5 0.5 0.6 0.6 0.6 0.6 0.7 0.7 0.7 0.7 0.8 0.8
131 100 0.4 0.5 0.6 0.7 0.7 0.7 0.8 0.8 0.8 0.9 0.9 1.0 1.0 1.0 1.1 1.1
151 100 0.8 1.2 1.3 1.5 1.6 1.6 1.7 1.8 1.9 1.9 2.0 2.1 2.2 2.3 2.3 2.4

BlazeBrake™Sealant
Fire Rated Acrylic
Key Features
• Complies to AS1530.4
• Fire rating of up to 4 hours
Sealants
• Fire rated to suit:

- concrete joint widths 10 mm to 80 mm
- copper pipe up to 80 mm dia.(nominal)
- multiple small copper pipes
- cable bundles
- concrete floor & walls
- plasterboard FR walls
VmOpliCant
• Acoustic rating
Co
Description
BlazeBrake™ 201 is a highly flexible fire rated and acoustic acrylic sealant,
suitable for interior and exterior sealing of concrete joints, cable, metal pipe
and service penetrations. Prevents the spread of flames, smoke and gases
through walls and floors or between building compartments.
Typical Properties
Colour Grey
Chemical Type Acrylic co-polymer
Service Temperature -20°C to + 90°C
Specific Gravity (Density) Wet 1.6 Kg / L Dry 1.8 Kg / L
Application Temperature +5°C to + 35°C
Tool Working Time 15 minutes at 25°C
Max. Joint Movement ± 15%
Max. Joint Width 50mm
Full Cure 7 days at 25°C
Rain resistant after 24 hours Features & Benefits
• Flexible and crack resistant
Acoustic Rating Rw 56
• Joint movement ± 15%
VOC 17 g / ml
• Suitable for exterior use (see precautions)
Fire Rating Up to 4 hours • Easy to dispense in cold weather.
Substrates • Non toxic. Low odour. Easy tooling
Concrete, Brickwork, Concrete Blockwork, FR Plaster Board, • Water clean up. Sag resistant
Fibre Cement Sheet • Not HAZARDOUS – no isocyanates, no heavy metals, no solvents
and no asbestos
• Low VOC
• Paintable with acrylic coatings and oil-based coatings after
Related Products 24 hours at 20°C.
BlazeBrake™ Foam - Fire Rated Self Expanding Polyurethane
FyreBrake™ Sealant - Fire Rated Polyurethane BlazeBrake™Sealant
Caulking Gun / Sausage Barrel Gun Order No. Pack Size Order Qty
Backing Rod BLBRGYC 300ml/450g cartridge 1
BLBRGYS 600ml/960g sausage 1

BlazeBrake™Sealant
Fire Rated Acrylic

Plumbing Electrical Mechanical Passive Fire Maintenance
Builder
Contractor Contractor Services Specialist Services
Precast and tiltup concrete walls 4 4 4 4 4 4
Concrete ceilings & floors 4 4 4 4 4 4
Metal pipe penetrations 4 4 4 4 4
Cable penetrations 4 4 4 4
Plasterboard FR wall 4 4 4 4 4 4
Installation
Consult technical data for tested applications and fire ratings, before commencing use. For detailed technical data and instructions go to
www.ramset.com.au. For applications outside those tested, refer to your Fire Consultant for compliance advice. Fire Rating Certificates Available on
Request. Refer to BRANZ Fire Test Certificates 439, 440 and 441.
Sealants
Cable and Metal Pipe Penetrations Sealing of Joints and Cavities
Up to 4 hours Fire Rating in Concrete Floor Up to 4 hours Fire Rating in Concrete Floor/Wall
Metal Pipe Penetration Metal Pipe Penetration Vertical Joints (up to 80mm) Floor Control Joint
• BlazeBrake™ Acrylic Sealant • BlazeBrake™ Acrylic Sealant • BlazeBrake™ Foam with or • BlazeBrake™ Acrylic Sealant
• Copper pipe up to 80mm (nom) • Multiple copper pipes - without Acrylic Sealant • Joint width 25mm
• Copper pipe 200mm (nom) 3 x 20mm (nom) • Joint width from 10 to 80mm • Sealant depth 12mm
• Joint depth from 100 to 200mm with foam backer rod
Up to 2 hours Fire Rating in Plasterboard FR Wall
Metal Pipe Penetration Electrical & Data Cables

• BlazeBrake™ Foam with or • BlazeBrake™ Acrylic Sealant
without Acrylic Sealant • Cable bundle -
• Steel pipe 34mm (nom) 65mm diam. (max)
2hr Deflection Head 2hr Intersection / Masonry
• BlazeBrake™ Acrylic Sealant • BlazeBrake™ Acrylic Sealant
Up to 2 hours Fire Rating in Plasterboard FR Wall • Joint width 20mm • Joint width 15mm
• FR wall thickness 26mm • FR wall thickness 26mm
2hr Metal Pipe Penetration 2hr Cable Penetration

• BlazeBrake™ Acrylic Sealant • BlazeBrake™ Acrylic Sealant 1hr Deflection Head 1hr Intersection / Masonry
• Copper pipe up to 80mm (nom) • Electrical and data cable • BlazeBrake™ Acrylic Sealant • BlazeBrake™ Acrylic Sealant
• FR wall thickness 26mm bundle 65mm diam. (max) • Joint width 20mm • Joint width 15mm
• FR wall thickness 26mm • FR wall thickness 16mm • FR wall thickness 16mm
1hr Metal Pipe Penetration 1hr Cable Penetration 2hr Control Joint 1hr Control Joint
• BlazeBrake™ Acrylic Sealant • BlazeBrake™ Acrylic Sealant • BlazeBrake™ Acrylic Sealant • BlazeBrake™ Acrylic Sealant
• Copper pipe up to 80mm (nom). • Electrical and data cable • Joint width 20mm • Joint width 20mm
• FR wall thickness 16mm bundle 65mm diam. (max) • FR wall thickness 26mm • FR wall thickness 16mm
• FR wall thickness 16mm • Rondo® P35 control joint • Rondo® P35 control joint

FyreBrake™Sealant
Fire Rated Polyurethane
Key Features
• Complies to AS1530.4
Sealants
• High joint movement ± 25%

• Acoustic 5 star rating (AAAC)
• Meets BCA acoustic requirements
VmOpliCant
Co
Description
FyreBrake™ is a high performance, 100% polyurethane construction sealant,
which does not shrink, dry out or crack. FyreBrake™ is fire and acoustic rated
for sealing residential and office partitions, concrete block, tilt-up and precast
concrete.
Typical Properties
Typical properties after 7 days cure at 25°C and 50% RH
Appearance Grey, Non sag smooth
thixotropic paste
Chemical Type Polyurethane
Specific Gravity 1.6
Sag ASTM C639 None
Tool Working Time 2 – 4 hours @ 24°C, 50% RH Features & Benefits
Cure Rate 2 mm per 24 hour period • VOC Rated
• UV and Weather Resistant. No sagging or running
Full cure within 7 days
• Easy to dispense in cold weather
Max. Joint Movement ± 25% • Strong adhesion. Excellent flexibility – joint movement ± 25%
Max. Joint Width 50mm • Non-corrosive neutral cure
Elongation at Break ASTM D412 500% • Paintable with acrylic based surface coatings
Cure Hardness ASTM C661 Shore A 47 • Complies with:
Peel Adhesion ASTM C794 67 N - TT-S-00230 C (Type II) Class A, Non-sag, One component
Max Tensile Strength ASTM D412 2.24 N/mm2 - ASTM C920 Type S, Grade NS, Class 25, Use-NT, Use-A, Use-M, Use-G, Use-O
- AAMA 808.3-92
Water Resistance AAMA 800 Passes
VOC 20 gram / litre
Acoustic Rating Up to Rw (STC) = 60
Rw + Ctr = 52 Related Products
Substrates Plasterboard, Fibre Cement Sheet, Solid Concrete, Brick, BlazeBrake™ Foam - Fire Rated Self Expanding Polyurethane
Concrete Block, Aluminium Steel BlazeBrake™ Sealant - Fire Rated (450g or 960g)
Caulking Gun / Sausage Barrel Gun
Backing Rod

FyreBrake™Sealant
Fire Rated Polyurethane

Ceiling & Partitioning Window & Door Passive Fire Maintenance
Builder
Contractor Installers Specialist Services
Precast and tiltup concrete walls 4 4 4 4
Concrete ceilings & floors 4 4 4 4
Plasterboard FR wall 4 4 4 4 4
Installation
www.ramset.com.au. For applications outside those tested, refer to your Fire Consultant for compliance advice. Fire Rating Certificates Available on
Request. Refer to (CSIRO Test Reports FS1202 & FS1203)
Sealants
Sealing of Joints and Cavities - in Concrete Floor/Wall
Up to 4 hours Fire Rating Up to 2 hours Fire Rating Up to 2 hours Fire Rating

Vertical Joints Plasterboard / Masonry Plasterboard / Plasterboard
(2 Sides Sealed) (2 Sides Sealed) (2 Sides Sealed)
• FyreBrake™ Sealant with backer rod • FyreBrake™ Sealant • FyreBrake™ Sealant with backer rod
• Joint width up to 20mm • Double wall • Double wall
• Joint depth 10mm • Joint width up to 20mm • Joint width up to 20mm
Acoustic Installation
The following detail was extracted from Graeme E. Harding & Associates Report 056-202, available from Ramset™ or the website.
Wall Construction
Frame: Rondo 92 mm wide floor, edge and head channels. Rondo 92 mm wide vertical channels at 600 mm spacings.
Cavity Insulation: 60 mm thick Bradford Soundscreen R1.6 Rockwool Partition Batts
Cladding - Transmission Side: 2 layers of 13 mm Boral fire rated plasterboard installed horizontally with nominal 10 mm gap top and bottom and 5 mm gap on
each side. Sheets of outer layer staggered to cover joins between sheets in inner layer. Joints were not taped or set.
Cladding - Receiving Side: 3 layers of 13 mm Boral fire rated plasterboard installed horizontally with nominal 10 mm gap top and bottom and 5 mm gap on
each side. Sheets of outer layers staggered to cover joins between sheets in inner layers. Joints were not taped or set.
Ramset™ Fyrebrake™ sealant was installed in the perimeter gaps after measuring sound insulation of the uncaulked wall.
Total Mass: 54.6 kg / m2 Total Thickness: 157 mm
Test Results
Rw (dB) Ctr (dB) Rw + Ctr (dB)
Uncaulked Wall 24 0 24
Wall caulked with
60 -8 52
Fyrebrake™ Sealant
The wall was designed to achieve an Rw = 58 + 2 dB. The test demonstrated that using Ramset™ Fyrebrake™ sealant in the perimeter gaps enabled the
wall’s full design insulation to be achieved.
FyreBrake™Sealant
Part No. Colour Volume Order Qty
FYBRGYS Grey 960g Sausage 1

Gap Seal
Paintable Acrylic Gap Sealant
Sealants
Features & Benefits

• Resists cracking - flexible
• Paintable
• User Friendly – clean up with water
• User Friendly – low odour
VmOpliCant
• Easy to use – sag resistant
• Low VOC
Co
Description Trades & Applications

Gap Seal paintable acrylic sealant is flexible to resist cracking when used to Ceiling &
seal gaps and cracks prior to painting. Gap Seal provides a neat and tidy Shop Fitter Painter
Partitioning
finish around architraves, skirtings, chair and picture rails and is paintable Sealing Partition
with acrylic and oil based surface coatings. 4 4
Joints
Sealing Joinery 4 4
Typical Properties
Appearance White, non-sag smooth thixotropic paste
Chemical Type Water-based Acrylic
Related Products
Caulking Gun
Tool Working Time 15 minutes at 20°C
Elongation at Break
400%
ASTM D412
Cure Rate 2mm per 24 hour period Installation
Cure Hardness Shore D 50 1. Ensure surfaces are clean and dry
2. For best results mask around gap to be filled
Skinning Time 30 minutes @ 20°C
3. Dispense Gap Seal sealant into gap or joint with continuous
Acrylic and Vinyl paints – 30 minutes at
Paintable trigger pressure
20°C Oil based paints – 24 hours
4. Tool sealant to create a neat finish
Substrates 5. Remove masking tape before Gap Seal Skins
Plasterboard, MDF, Plywood, Ceramic Tiles, Laminated Plastics, Timber, 6. Clean up Gap Seal with a damp cloth before it dries.
Fibre cement, Concrete & Brick Refer to Technical Data Sheet and MSDS available from
Flexibility Low Low VOC Yes
Water Resistance Low Paintable Yes
Water Immersion No Water Clean Up Yes
Gap Seal
Heat Resistant No Exterior Use No Part No. Colour Volume Order Qty
Fire Rated No UV Resistant No GPSLWHG450 White 300mL Cartridge 20

Duct Seal
Sheet Metal Duct Sealant
Sealants
Features & Benefits
• Flexible and tough – resists blow-out
• Paintable
• Solvent Free
- Low Odour
VmOpliCant
- Not flammable
- Clean up with water
- Zero VOC
Co

Duct Seal is tough and flexible to prevent air leakage when used to seal lap Mechanical Services
joints in sheet metal ductwork. It is made from low odour water borne acrylic Sealing Duct Work 4
polymer for easy clean up and user comfort.
Typical Properties
Appearance White, smooth thixotropic paste
Chemical Type Water-based Acrylic
Related Products
Caulking Gun
Application
+5°C to + 35°C
Temperature
Acrylic and Vinyl paints – 30 minutes at 20°C
Paintable
Oil based paints – 24 hours
Substrates Galvanised Steel
Installation
1. Ensure surfaces are clean and dry
2. Dispense Duct Seal onto one surface and assemble components.
3. Drill and rivet lap joint as required
4. Protect from contact with water for at least 12 hours
5. Pressure test after 48 hours at 20°C. Longer in low temperatures or
high humidity.

Water Immersion No Water Clean Up Yes Duct Seal
Fire Rated No UV Resistant No DSLWG450 Grey 300mL Cartridge 20

DynaSeal™
Acrylic Construction Sealant
Sealants
Features & Benefits

• User Friendly
• No Fumes
• Low VOC
• Water Clean Up
VmOpliCant
• Easy Dispensing in Cold Weather
• Elastic and Flexible
• Paintable with acrylic based surface coatings
Co • Non-toxic
• Easy tooling

DynaSeal™ is a flexible acrylic/urethane co-polymer sealant for general joint Ceiling & Sealing &
sealing in building and construction applications. For internal and external Bricklayer Shop Fitter
Partitioning Waterproofing
conditions. DynaSeal™ Sealant provides a flexible, elastic seal in joints in Partition
interior fit-out and concrete, brick and concrete block-work construction. 4
Joints
Precast Joints 4
Brick & Block
Typical Properties Joints
4
Appearance Non sag smooth thixotropic paste Joinery 4
Chemical Type Polyurethane / Acrylic co-polymer
Specific Gravity 1.5 Related Products
Application Temperature +5°C to + 35°C Battery Powered Caulking Gun
Tool Working Time 15 minutes at 25°C Nozzle Set
Max. Joint Movement ± 20% Backing Rod
Elongation ASTM D412 290 to 340% Installation
Full Cure 7 days at 25°C 1. Ensure surfaces are clean and dry
Substrates 2. For best results mask around gap to be filled
Timber, Concrete, Concrete Block, Medium Density Fibreboard (MDF), 3. Dispense Dynaseal™ sealant into gap or joint with continuous
Hardboard, Particleboard, Plywood, Brick, Plasterboard, Fibre Cement trigger pressure
Sheet, Ceramic Tiles (unglazed edges), Laminate 4. Tool sealant to create a neat finish
5. Remove masking tape before Dynaseal™ skins
6. Clean up Dynaseal™ with a damp cloth before it dries.
Flexibility Mod. Low VOC Yes
Water Resistance Mod. Paintable Yes
Water Immersion No Water Clean Up Yes DynaSeal™
Heat Resistant No Exterior Use Yes
DYSLGRG450 Grey 300mL Cartridge 20
Fire Rated No UV Resistant Yes DYSLGYG900 Grey 600mL Sausage 15

HiSeal™
Polyurethane Construction Sealant
Sealants
Features & Benefits
• UV and Weather Resistant
- Excellent resistance to aging and weathering
• Low VOC
• High bond strength
VmOpliCant
• Thixotropic - No sagging or running
• Excellent flexibility – joint movement ± 25%
• Suitable for Acoustic Applications
Co • Suitable for contact with drinking water – AS4020-1994
• Non-corrosive neutral cure
• Paintable with acrylic based surface coatings

HiSeal™ is a high performance polyurethane sealant that provides a tough, Ceiling & Sealing &
elastic, UV resistant and weatherproof seal in exterior joints in concrete, Bricklayer Shop Fitter
Partitioning Waterproofing
brick and concrete block-work construction. Highly resistant to dynamic joint Partition
movement. 4
Joints
Precast Joints 4
Brick & Block
Typical Properties Joints
4
Appearance Non sag smooth thixotropic paste Joinery 4
Chemical Type Polyurethane
Specific Gravity 1.2
Related Products
Tool Working Time 30 minutes at 20°C Battery Powered Caulking Gun
Tack Free Time 6 to 12 hours Nozzle Set
Cure Rate 2 mm per 24 hour period Backing Rod
Max. Joint Width 50mm Installation
Elongation at Break 900% Mask around joints before applying sealant.
Cure Hardness Shore A 30 Dispense HiSeal™ into joint. Tool sealant for neat finish.
Tensile Strength 1.3 N / mm2 Use tool with a convex profile.
Service Temperature -40°C to + 70°C Tooling Time: within 30 minutes of application.
Substrates Remove masking tape before sealant skins (about 30 minutes).
Concrete and Cement, Brick, Concrete Block, Aluminium, Ceramic Tiles, Refer to Technical Data Sheet and MSDS available from
Laminate, Stainless Steel, Galvanised Steel, Timber, Particleboard, MDF, www.ramset.com.au, for precautions and further detailed
Plywood, Plasterboard installation instructions
Approvals
AS4020-1994 Contact with drinking water
Flexibility High Low VOC Yes AS1157-1972 Fungus and mildew resistance
Water Resistance High Paintable Yes

Water Immersion No Water Clean Up No HiSeal™
HYSLGYG375 Grey 300mL Cartridge 25
Fire Rated No UV Resistant Yes HYSLGYG720 Grey 600mL Sausage 20

Water Seal
Sanitary Grade Construction Sealant
Sealants
Features & Benefits

• Waterproof – retains adhesion and flexibility in contact with water
• Permanently flexible
• Sag Resistant – No sagging or running
• Mould and Mildew Resistant
VmOpliCant
• Excellent flexibility – joint movement ± 25%.
• Strong adhesion
Co

Water Seal is waterproof and contains a fungicide to inhibit mould growth, Plumber Shop Fitter
for general wet-area applications, such as bathrooms, kitchens and Sealing around bathroom
laundries. Water Seal is permanently flexible to resist cracking making it a 4 4
fixtures
perfect replacement for tile grout in internal corners and around baths and Sealing around kitchen fixtures 4 4
vanity basins.
Sealing around laundry fixtures 4
Typical Properties
Chemical Type Acetoxy Silicone
Skin Time BS5889 6 minutes
Tack Free Time ASTM C679 30 minutes
Tool Working Time ASTM C679 Up to 10 min @ 25°C 50%RH
Slump MIL – A-46106A None
Application Temperature -10 to 40°C
Cure Rate 1.3 mm / 24 hours Related Products
Service Temperature -50 to 150°C Caulking Gun
Max. Joint Movement ASTM C920 ± 25%
Tensile Strength ASTM D412 1.80 N / mm2
Modulus at 100% Elongation Installation
0.40 N / mm2 1. Ensure surfaces are clean and dry
ASTMD412
Elongation at Rupture ASTMD412 520% 2. For best results mask around gap to be filled
3. Dispense Water Seal sealant into gap or joint with continuous
Peel Strength after UV Through
50 N / 25 mm trigger pressure
Glass FED TT-00-1543A
4. Tool sealant to create a neat finish
Cure Hardness ASTM C661 Shore A 20
5. Remove masking tape before Water Seal skins
Substrates 6. Clean up Water Seal with mineral turps before it sets.
Glass, Anodised Aluminium, Colour Coated Steel and Aluminium, Refer to Technical Data Sheet and MSDS available from
Timber, Laminate, Acrylic, Stainless Steel, Vitreous Enamel, Glazed www.ramset.com.au, for precautions and further detailed
Ceramics, Unglazed Ceramics installation instructions
Flexibility High Low VOC Yes
Water Resistance High Paintable No
Water Immersion Yes Water Clean Up No Water Seal
Heat Resistant Yes Exterior Use Yes Part No. Colour Volume Order Qty
Fire Rated No UV Resistant Yes WRSLWHG300 White 300mL Cartridge 20

Roof Seal
Neutral Cure Construction Sealant
Sealants
Features & Benefits
• UV and Weather Resistant
- Excellent resistance to accelerated aging and weathering to ASTM C792
• Excellent flexibility – joint movement ± 25%
• Thixotropic - No sagging or running
VmOpliCant
• Suitable for contact with drinking water – AS4020-1994
• Non-corrosive neutral cure silicone
• Low VOC
Co

Roof Seal is UV and weather resistant for exterior plumbing and roofing Plumber Electrician Concreter Bricklayer
applications. Its neutral cure formula is non-corrosive so it is safe to use with Sealing flashings,
all metals including galvanised steel and anodised aluminium. Also suitable 4
guttering & downpipes
for cement, brick and concrete. Sealing penetrations
4 4
through concrete
Typical Properties Sealing penetrations
4 4
Chemical Type Oxime Silicone through steel
Skin Time BS5889 8 minutes Sealing concrete
4 4
expansion joints
Tack Free Time ASTM C679 30 minutes
Sealing brick & Block
Tool Working Time ASTM C679 Up to 10 min @ 25°C 50%RH 4 4
expansion joints
Slump BS5889 None
Application Temperature -10 to 40°C
Cure Rate 1.0 mm / 24 hours Related Products
Service Temperature -50 to 150°C Caulking Gun
Max. Joint Movement ASTM C920 ± 25%
Tensile Strength ASTM D412 1.10 N / mm2
Modulus at 100% Elongation
0.40 N / mm2
Installation
ASTMD412 1. Ensure surfaces are clean and dry
Elongation at Rupture ASTMD412 630% 2. For best results mask around joint to be sealed
Peel Strength after UV Through 3. Dispense Roof Seal onto one surface and assemble components.
50 N / 25 mm 4. Drill and rivet lap joint as required
Glass BS5889
Cure Hardness ASTM C661 Shore A 17 - 22 5. Remove masking tape before Roof Seal skins
VOC 40 g / litre 6. Clean up Roof Seal with mineral turps before it sets.
Substrates
Galvanised Steel, Aluminium, Colour Coated Steel (eg. Colorbond®), Timber,
Terracotta, Rigid PVC, Pipe, Brick, Concrete and Cement
Flexibility High Low VOC Yes
Water Resistance High Paintable No Roof Seal
Water Immersion Yes Water Clean Up No
RFSLTRG300 Translucent 300mL Cartridge 20
Heat Resistant Yes Exterior Use Yes
RFSLALG300 Aluminium 300mL Cartridge 20
Fire Rated No UV Resistant Yes RFSLGYG410 Grey 300mL Cartridge 20

NailFree™
Construction Adhesive
Adhesives
Features & Benefits

• Effective on uneven surfaces - Bridges gaps up to 9mm
• Reduces squeaking associated with nail ride in floors.
• Repositionable up to 20 minutes after application or bonds instantly using
contact method
• Reduces number of mechanical fasteners required to install floors or walls.
• Natural wood colour
• Strong adhesion to metal

NailFree™ is a synthetic rubber based adhesive for flooring, joinery, wallboards Carpenter Shop Fitter
and other general construction assembly. NailFree™ forms strong bonds to a Bonding Flooring to Joists 4
wide variety of building materials in interior and exterior conditions. Bonding wall panels to studs 4 4
Typical Properties Bonding Architraves & Skirting
4 4
Open Time 1-5 mins. boards
Full cure 24 hours @ 25°C
Repositioning time < 20 mins @ 25°C
Service Temperature 0°C to 40°C
Application Temperature 5°C to 35°C Related Products
Sag Resistance (AS2329-1999, Appendix A) < 6mm Caulking Gun (300ml or 850ml)
Transfer > 75% after 15 min. open
(AS 2329 - 1999, Appendix B) time
Aging No chipping or cracking
(AS2329-1999, Appendix C) after 500 hours at 70°C. Installation
Initial Bond Strength in Shear 1. Ensure surfaces are clean and dry
> 200 kPa
(AS2329-1999, Appendix D) 2. Dispense Nail Free™ onto joists or studs as a continuous bead
Adhesion Strength in Tensile Shear 3. Place floor or wall panel onto joists or studs and align
> 1 MPa
(AS2329-1999, Appendix E) 4. Nail or screw as required
Bond Strength in Peel 5. Clean up Nail Free™ with mineral turps before it dries
> 40N/25mm
(AS2329 - 1999, Appendix F) Refer to Technical Data Sheet and MSDS available from
Peel Strength after UV Through Glass FED www.ramset.com.au, for precautions and further detailed
50 N / 25 mm
TT-00-1543A installation instructions
Cure Hardness ASTM C661 Shore A 20
Substrates Particleboard / Chipboard, Medium Density Fibreboard (MDF),
Fibre Cement Sheet, Softwoods , Hardwoods,Hardboard, Plywood,
Polyurethane Foam, Expanded Polystyrene Foam, Galvanised steel Approvals
AS2329-1999
Flexibility Low Low VOC No
Water Immersion No Water Clean Up No
NailFree™
Part No. Volume Order Qty
Heat Resistant No Exterior Use Yes NFCAG320 300mL Cartridge 10
Fire Rated No UV Resistant No NFCAG930 850mL Cartridge 10

Safe-T-Bond™
Construction Adhesive
Adhesives
Features & Benefits
• Low odour – no solvent fumes
• Easy to use
- Easy clean up - use water
- F ast initial grab - minimises slippage on vertical surfaces.
VmOpliCant
-E asy to dispense at low temperatures.
- B ridges gaps up to 9 mm - effective on uneven surfaces
- L ong repositioning time -
Co up to 60 minutes
- E asy to use, re-sealable sausage – no caulking gun
• Will not attack polystyrene foam

Safe-T-Bond™ is formulated with strong initial suction / grab, which makes it Carpenter Shopfitter Builder
ideal for installing wall panelling, flooring, skirting boards and architraves. It Bonding Flooring
has no fumes and can be cleaned up with water. 4 4
Panels to Joists
Typical Properties Bonding wall panels
4 4 4
Open Time 20 min @ 25°C to studs
Cure Time 24 hours @ 25°C Bonding Architraves &
4 4 4
Repositioning Time 60 minutes @ 25°C Skirting boards
Bonding Polystyrene
Service Temperature -5°C to 80°C 4 4 4
Foam
Application Temperature 5°C to 35°C
Flammability Not Flammable
Sag Resistance Related Products None Required
< 6mm
(AS2329-1999, Appendix A)
Transfer > 75% after 15 minutes open Installation
(AS 2329 - 1999, Appendix B) time 1. Ensure surfaces are clean and dry
Aging No chipping or cracking after 2. Cut sachet tip to desired diameter.
(AS2329-1999, Appendix C) 500 hours at 70°C. 3. Dispense Safe T Bond™ by squeezing sachet
Initial Bond Strength in Shear 4. Apply adhesive as a continuous bead onto studs or joists.
> 200 kPa 5. Place floor or wall panel onto joists or studs and align
(AS2329-1999, Appendix D)
Adhesion Strength in Tensile Shear 6. Nail or screw as required
> 1 MPa 7. Clean up Safe T Bond™ with a damp cloth before it dries
(AS2329-1999, Appendix E)
8. Brace and support wall panels or light objects and remove when adhesive
Bond Strength in Peel
> 40N/25mm has set (approximately 24 hours).
(AS2329 - 1999, Appendix F)
Substrates
Particleboard / Chipboard, Medium Density Fibreboard (MDF), Fibre Cement
Sheet, Softwoods , Hardboard, Plywood, Hardwoods with dry density <
1000 Kg / m3, Concrete, Expanded Polystyrene Foam, Galvanised steel
Approvals
Bond strength exceeds requirements of AS2329 - 1999
Water Immersion No Water Clean Up Yes
Safe-T-Bond™
Fire Rated No UV Resistant No STBDL1 White 1 Litre Sausage 10

BlazeBrake™Foam
Fire Rated Expanding Polyurethane
Self-Expanding Foams
Key Features
• Complies to AS1530.4-2005
• Fire rated to suit:
- joint widths 10 mm to 80 mm
- joint depths 100 mm to 200 mm
- 34 mm diameter (nominal) steel pipe
• No dispensing tools required
• Acoustic rating ISO140
VmOpliCant
Co
Description
BlazeBrake™ Fire Rated Foam is a one component expanding PU foam
suitable for sealing construction joints and service penetrations. It prevents
the penetration and transfer of flames, smoke and gases between building
compartments. BlazeBrake™ FR Foam reacts with moisture in the air
causing it to expand to fill any shaped hole or cavity. The cured foam can
then be cut or shaped and painted as desired.
Typical Properties
Density 20 to 28 Kg / m3
Yield, Free Expansion 37 litre average
Maximum expansion obtained with
container at 20°C. Cold, heat and low
humidity will result in lower yields.
Tack Free 10 min, 23°C, 50% RH
Cuttable (30 mm dia bead) 60 min, 23°C, 50% RH
Weight Bearing Time (30 mm dia bead) 24 hours, 23°C, 50% RH
Heat conductivity coecient DIN52612 25 to 30 mW/m.K Features & Benefits
Compressive Strength ISO844 75 kPa (10% Deformation) • 50% post expansion rate
Tensile Strength DIN53455 60 kPa • Suitable for sealing gaps around window and door frames
Elongation at Break DIN53455 20% • Sound dampening and sealing against draughts and moisture
Shear Strength DIN53422 30 kPa • High bond strength
• Excellent dimensional stability
Water Absorption DIN53428 0.3 vol%
• Can be painted and covered with plaster
Temperature Resistance (Long Term) -40 to 90°C
• Excellent thermal insulator
Temperature Resistance (Short Term) -40°C to 130°C • CFC & HCFC free (ozone layer friendly)
Application Temperature Ambient: +5°C up to +35°C • VOC data available
Can: +10°C up to +30°C
Acoustic Rating ISO 140 R ST ,W (C;C tr) 58
Shelf Life 9 months maximum
Related Products
BlazeBrake™ Sealant - Fire Rated Acrylic (450g Cartridge or 960g Sausage)
Fomo Cleaning Solvent (500ml Aerosol Can - FMSVM500)

BlazeBrake™Foam
Fire Rated Expanding Polyurethane

Builder
Small metal pipe penetrations 4 4 4 4 4
Installation
www.ramset.com.au. For applications outside those tested, refer to your Fire Consultant for compliance advice.
Surface rebate filled with

BlazeBrake™ FR Acrylic Sealant
(if required)
Internal joint cavity filled with

BlazeBrake™ FR Foam
Metal Pipe Penetration Vertical Joints (up to 80mm)

• BlazeBrake™ Foam with or without Acrylic Sealant • BlazeBrake™ Foam with or without Acrylic Sealant
• Steel pipe 34mm (nom) • Joint width from 10 to 80mm
• Joint depth from 100 to 200mm
Concrete Slab Installation Data Source: CSIRO report FCO2662

Dimensions in mm
Rebate Filler FRL
Joint Width Joint Depth Rebate*
10 210 10 FR Silicone -/240/240
20 210 - - -/240/240
10 210 - - -/240/240
20 210 10 FR Silicone -/240/240
20 200 10 FR Silicone -/240/240
20 200 10 BlazeBrake™ Sealant -/240/240
20 200 - - -/180/180
80 210 - - -/60/60
60 210 - - -/90/90
40 210 - - -/180/180
Concrete Block Wall Installation Data

Dimensions in mm
Rebate Filler FRL
Joint Width Joint Depth Rebate
10 100 - - -/120/120
20 100 - - -/60/60
Steel Pipe through Aerated Concrete Block Wall Installation Data Source: CSIRO report FCO2680
Dimensions in mm
Rebate Filler FRL
Hole Dia Pipe Dia Hole Depth Rebate
80 34 150 - - -/60/60
80 34 150 10 BlazeBrake™ Sealant -/240/90
BlazeBrake™Foam
FRF700 Light Grey 750mL Can 1

FomoFill™
Straw Applied
Self-Expanding Polyurethane Foam
Features & Benefits

• Expands to fill BIG holes
• Once cured, can be cut and shaped as required
• Non-shrink
• Can be sanded, filled and painted to produce a neat finish.
VmOpliCant
• Excellent insulator
• Closed cell structure
• Ozone friendly – CFC, FC and HFC free
Co

Versatile FomoFill™ is a polyurethane polymer that reacts with moisture in the Shop- Mech
Carpenter Builder Plumber Electrician
air causing it to expand to fill any shaped hole or cavity. The cured foam can fitter Services
then be cut or shaped and painted as desired. FomoFill™ is great for thermal Penetrations
insulation, to block out drafts or to fill or repair big holes prior to painting. through walls 4 4 4 4
Typical Properties & floors
Yield, Free Expansion 500 g Can Approx. 12 to 30 L Sealing large
4 4
Yield, Free Expansion 750 g Can Approx. 17 to 45 L gaps
Bulk Density 13 Kg / m3 Filling gaps be-
Raw Density (Confined) 25 Kg / m3 tween window 4 4 4
& door frames
Tack Free Time 10 minutes
Cuttable (20 mm Dia Bead) 30 minutes
Full Cure (20 mm Dia Bead) After 12 Hours Related Products
Fomo Cleaning Solvent (500ml Aerosol Can - FMSVM500)
Application Temperature Min 5°C Max 25°C
Optimum Application Temp 20°C Installation
Water Absorption (DIN53428) 0.3 Vol % 1. Protect surfaces around work area from unwanted drips
2. To aid foam expansion, dampen surfaces using water spray
Thermal Conductivity (DIN52612) 0.04 W / mK
bottle or similar
Long Term -15°C to 60°C 3. Screw nozzle onto valve on top of can. Take care not to over tighten
Service Temperature Limits or activate the valve.
Short Term -40°C to 130°C
4. Shake can vigorously for approximately 60 seconds, turn can upside
Shelf Life 9 months down, then point nozzle into the cavity to be filled and depress trigger to
Substrates dispense the foam
Particleboard / Chipboard, Medium Density Fibreboard (MDF), Fibre Cement 5. Fill cavity to about 1/3 full. Foam will expand and fill cavity
Sheet, Timber , Hardboard, Plywood, Concrete, Plasterboard, Galvanised 6. Clean up FomoFill™ with Fomo Cleaning Solvent before it sets
steel, Brick, Mild steel, Ceramic tiles, Acrylic, Cardboard, Stone, Aluminium, Refer to Technical Data Sheet and MSDS available from
Concrete Block, Rigid PVC www.ramset.com.au, for precautions and further detailed
Flexibility Low Low VOC Yes installation instructions
FomoFill™
Heat Resistant No Exterior Use Yes FMFLG500 500mL Aerosol Canister 12
Fire Rated No UV Resistant No FMFLG750 750mL Aerosol Canister 12

FomoPlus™
Gun Applied
Self-Expanding Polyurethane Foam
All Metal Applicator
(FMPLGU300)
Controlled Flow Applicator Features & Benefits

(FMPLGU) • Expands to completely fill voids
• Closed cell foam structure - efficient temperature insulation
• Applicator provides neat, accurate dispensing
• Reusable
VmOpliCant
• Ozone friendly – CFC, FC and HFC free
• Closed cell structure
• Resistant to blockages – ideal for stop / start work
Co

Versatile FomoPlus™ is a polyurethane polymer that reacts with moisture Shop- Elec- Mech Con-
in the air causing it to expand to fill any shaped hole or cavity. The cured Carpenter Builder Plumber
fitter trician Services creter
foam can then be cut or shaped and painted as desired. The FomoPlus™ Penetrations
applicator ensures foam is dispensed accurately to provide a neat finish and through walls 4 4 4 4
reduce waste. FomoPlus™ is ideal for thermal insulation, to block out drafts & floors
or to fill or repair big holes prior to painting. Sealing large
Typical Properties gaps
4 4
Yield, Free Expansion 750 g Can 17 to 45 litres Filling gaps -
(bulk density approx. 15 kg/m3) window & 4 4 4
Tack-free time 4 - 10 minutes door frames
Cuttable (20 mm dia. bead) 7 - 9 minutes Filling gaps
4
Full stability load bearing (20mm After 12 hours in formwork
dia. bead)
Related Products
Working temperature Min + 5°C Max + 25°C Controlled Flow Applicator
Optimum working temperature + 20°C All Metal Applicator
Water absorption (DIN 53433) 0.3 Vol. -% Fomo Cleaning Solvent (500ml Aerosol Can - FMSVM500)
Thermal conductivity approx. 0.04 W / mK Installation
Service Temperature Long-term- 40°C to + 80°C 1. Protect surfaces around work area from unwanted drips
2. To aid foam expansion, dampen surfaces using water spray bottle
Service Temperature Short-term- 40°C to + 100°C
or similar
Shelf-life 9 months 3. Fit canister onto applicator gun. Take care not to over tighten or
activate the valve.
Substrates
4. Shake can vigorously for approximately 60 seconds, then point gun nozzle
Particleboard / Chipboard, Medium Density Fibreboard (MDF), Fibre Cement
into the cavity to be filled and depress trigger to dispense the foam
Sheet, Timber , Hardboard, Plywood, Concrete, Plasterboard, Galvanised
5. Fill cavity to about 1/3 full. Foam will expand and fill cavity
steel, Brick, Mild steel, Ceramic tiles, Acrylic, Cardboard, Stone, Aluminium,
6. Clean up FomoPlus™ with Fomo Cleaning Solvent before it sets
Concrete Block, Rigid PVC
Flexibility Low Low VOC Yes www.ramset.com.au, for precautions and further detailed
Water Resistance High Paintable Yes installation instructions
FomoPlus™
Fire Rated No UV Resistant No FMPLG750 750mL Aerosol Canister 12

CemCrete™
Polymer Bonding & Sealing Agent
Additives
Features & Benefits

• Improves strength and toughness of cement mixtures
• Improves adhesion of cement mixtures to existing concrete, brick and
block
• Strong bond
VmOpliCant
• Economical
- High concentration
- High molecular weight polymer
Co - High dilution

CemCrete™ is a high molecular weight polymer concentrate, which is diluted Concreter Bricklayer Solid Civil Factory Builder
and added to cement mixtures to reduce cracking and improve adhesion. Plasterer Contractor Fitter
CemCrete™ also aids bonding of concrete, renders, mortars and toppings Bonding to
to existing concrete, block and brick. CemCrete™ is ideal for priming porous concrete & 4 4 4 4 4
surfaces for ceramic tiling and to add flexibility to cement tile grouts and brick
adhesives. Improve ad-
hesion and 4 4 4 4 4 4
Typical Properties toughness
Chemical Type High molecular weight resin dispersion
Service Temperature -15° C to +45°C Related Products
Application Temperature +10°C to +40°C Small Spiral Mixing Paddle (Mixtures up to 4L)
Colour White in wet state. Dries clear. Large Spiral Mixing Paddle (Mixtures greater than 4L)
1 part Cemcrete™
Sealing Coat 4 parts water
35 m2 / litre Coverage
Installation
1. Ensure surfaces are clean
1 part Cemcrete™ 2. Primer / Sealer: Prime surface with 1 part Cemcrete™ in 4 parts water
Bond Coat 1 part water 3. Bond Coat: Apply bond coat of 1 part Cemcrete™ and 1 part water
15 m2 / litre Coverage 4. Apply primer / bond coat with brush, roller or airless spray
1 part Cemcrete™ 5. Cement admixture: Add 1 part Cemcrete™ in 1.5 parts water as gauging
Cement Admixture 1.5 parts water water in render / solid plaster / mortar / concrete / grout
Coverage not applicable Refer to Technical Data Sheet and MSDS available from
Concrete, Concrete Block, Brick, Timber, www.ramset.com.au, for precautions and further detailed
Substrates installation instructions
Fibre Cement Sheet, Plasterboard
CemCrete™
CMCRL20 20 Litre Jerry Can 1
CMCRL5 5 Litre Jerry Can 1

ConcreBond™
Acrylic Polymer Bonding
& Sealing Agent
Additives
Features & Benefits
• Improves strength and toughness of cement mixtures
• Improves adhesion of cement mixtures to existing concrete, brick and
block
• Strong bond
VmOpliCant
• Economical
- High concentration
- High dilution
Co • Greater water resistance than conventional bonding agents

ConcreBond™ improves toughness and adhesion when added to cement Concreter Bricklayer Solid Civil Factory Builder
based mixtures such as render, concrete, mortar, grout and tile adhesives. Plasterer Contractor Fitter
ConcreBond™ is an acrylic emulsion polymer, which has higher water Bonding to
resistance than conventional concrete bonding agents. concrete & 4 4 4 4 4
brick
Typical Properties Improve ad-
Chemical Type Acrylic Resin Dispersion hesion and 4 4 4 4 4 4
Service Temperature -15°C to + 45°C toughness
Application Temperature +10°C to + 40°C Improve
Colour White in wet state. Dries clear. water
resistance 4 4 4 4 4 4
1 part Concrebond™
of concrete
Undiluted 0 parts water
& cement
Sealing Coat 3 parts water
Related Products
Small Spiral Mixing Paddle (Mixtures up to 4L)
Large Spiral Mixing Paddle (Mixtures greater than 4L)
Bond Coat 1 part water
Installation
1. Ensure surfaces are clean
1 part Concrebond™ 2. Primer / Sealer: Prime surface with 1 part Concrebond™ in 3 parts water
Cement Admixture 5 parts water 3. Bond Coat: Apply bond coat of 1 part Concrebond™ and 1 part water
Coverage not applicable 4. Cement admixture: Add 1 part Concrebond™ in 5 parts water as gauging
Concrete, Concrete Block, Brick, Timber, water in render / solid plaster / mortar / concrete / grout
Substrates
Fibre Cement Sheet, Plasterboard Refer to Technical Data Sheet and MSDS available from
ConcreBond™
CNBDL20 20 Litre Jerry Can 1

Premier Grout MP™
Class A Non-Shrink Cement Grout
Grouts
VmOpliCant
Co
Description Features & Benefits

Premier Grout MP™ is a Class A, non shrink cement grout that complies • High Strength
with AS MP20, Part 3 (1977). The product consists of a speciality blend • Non-shrink - Good dimensional stability - Complete void filling
of cement, graded aggregate and other chemically reactive agents that • Versatile - Can be dry packed, rammed, trowelled, poured and pumped over
compensate for drying shrinkage commonly found in cement products. short distances
Premier Grout MP™ does not contain any ferrous material or Calcium • Economical, low in-place cost
Chloride. High strength Premier Grout MP™ will not shrink making it ideal for • Ready to use, pre mixed, requires only the addition of water.
filling holes and voids in concrete for installing and repairing posts, bolts, • Non-staining – chloride and iron free
pipe penetrations or structural underpinning. • Lower water/cement ratio - Reduced drying shrinkage
- Increased hardness and durability
• Reduces Permeability
Typical Properties
Consistency
Dry Pack Trowellable Flowable
Litres of water per 20Kg Bag 2.0 2.5 - 3.0 3.5 - 4.0
Initial Set 1.5 hrs 1.5 hrs 1.5 hrs
Vicat Setting Times @ 20°C (AS1012.18)
Final Set 4.0 hrs 4.0 hrs 4.0 hrs
Start (Plastic State) - 30 min 30 min
Time for expansion (AS2073)
Finish (Plastic State) - 2.0 - 2.5 hrs 2.0 - 2.5 hrs
Unrestrained Expansion (AS2073) - >2% >1.5%
Bleeding (AS1012.6) 0% 0% 0%
1 Day 40 MPa 25 MPa 15 MPa
3 Days 60 MPa 45 MPa 25 MPa
Compressive Strength @ 20°C (AS1012.9 & AS2073)
Flexural Strength 1 Day - 8.5 MPa -
(ASTM C348) @ 20°C 7 Days - 11.0 MPa -
Substrates Concrete

Premier Grout MP™
Class A Non-Shrink Cement Grout

Steel Fabricator Ballustrader Concreter Civil Contractor Factory Fitter Builder
Filling gaps under base plates 4 4
Filling gaps under concrete panels 4 4 4
Filling grout tubes 4 4
Grouting bridge beam supports 4 4
Filling under machinery baseplates 4
Anchoring rod & bar into concrete 4 4 4 4 4
Approvals Related Products
Grouts
AS MP20, Part 3 (1977) Small Spiral Mixing Paddle (Mixtures up to 4L)
Installation
1. Grind old concrete to expose fresh concrete surface. Pre soak concrete for a minimum of 6 hours prior to placing Premier Grout MP™.
2. Measure the quantity of clean water accurately and add to a container with at least 20L capacity per bag of grout.
3. DO NOT MIX BY HAND.
4. Mix Premier Grout MP™ using a mechanical forced action mixer with a high shear stirrer such as Ramset LSMP.
5. Slowly add the dry Premier Grout MP™ powder while mixing.
6. Continue to mix for approximately 1 minute after all grout powder is added. The grout consistency must be uniform and homogenous.
7. DO NOT ADD ADDITIONAL WATER.
8. Discard any unused grout that has stiffened or hardened.
Placing
8. Remove excess water from concrete surface prior to pouring Premier Grout MP™.
9. To ensure maximum expansion, place grout within 30 minutes of mixing at 20°C.
10. Maximum thickness: 150 mm
11. Minimum thickness: 10mm
12. For section thicknesses > 150 mm, apply grout in several pours allowing the previous one to cool; dowelling between pours will provide better
adhesion for subsequent topping.
13. Avoid trapping air and water by placing grout from one side only
14. Use a suitable head box to ensure void is completely filled and to ensure continuous flow
15. To assist flow, rod the grout while pouring
16. Do not use mechanical vibrators to assist grout flow as this will cause segregation of the aggregate and bleeding
Refer to Technical Data Sheet and MSDS available from www.ramset.com.au, for precautions and further detailed installation instructions
Consistency
Strength Development and Yeild
Dry pack Trowellable Flowable
1 Day 40 MPa 25 MPa 15 MPa
Compressive Strength 3 Days 60 MPa 45 MPa 25 MPa
@ 20°C (AS1012.9 &
AS2073) 7 Days 65 MPa 55 MPa 40 MPa
Flexural Strength 1 Day - 8.5 MPa -
(ASTM C348) @ 20°C 7 Days - 11.0 MPa -
Litres per 20 kg Bag 10.3 11.0 11.7
Yield Fresh wet density kg / m3 1,950 1,800 1,750
Bags per cubic metre 96 90 87
Premier GroutMP™
RPGMP 20kg Bag 1

Epoxy Grout
2 Part Grouting Epoxy
Grouts
VmOpliCant
Co

Epoxy Grout is a 2-part 100% solventless epoxy resin with graded fillers, • High flow properties – good bonding and penetration
which can be used as is or with additional fillers to create a range of • Bonds to dry and damp concrete
application consistencies. Epoxy Grout is tough, durable and specially • Pre-measured kits to avoid measuring errors
formulated for strong bond to concrete, brick and block. • High tensile and compressive strength
• Cures at temperatures down to 5°C
• 100% solids epoxy – solvent free and negligible shrinkage
Related Products • High mechanical strength
Small Spiral Mixing Paddle (Mixtures up to 4L) • Resistant to vibration and dynamic loads
Large Spiral Mixing Paddle (Mixtures greater than 4L) • Add graded sand to change consistency
FillersFG™ Fine Grade Sand Filler
Typical Properties
Part A: Grey thixotropic liquid
Appearance Part B: Amber liquid
Grey when mixed together
Viscosity Flowable, pourable Hardness > 80 Shore D
Solid content by weight 100%
Pot life 45 – 50 mins @ 25°C
Tensile strength 30 MPa approx.
Tack free time 1.5 – 2.5 hours @ 25°C
Compressive strength 7
110MPa approx.
days Mix ratio 5:1 (part A:B) by volume
Compressive Strength 24 Min. Application temp. 5°C
88 MPa approx.
hours
Max. Application temp. 35°C
Flexural strength 25 MPa approx.
Density 1.53 kg/Litre
Tensile bond strength 10 MPa approx.
Water absorption* <0.2% (10 days at 25°C)
Modulus of elasticity 4.5 x 103 MPa
Full cure 7 days at 25°C
Service temperature -10°C to + 65°C
Min. Thickness 1.5mm
Heat distortion temp 80°C approx. Max. Thickness 50mm
Substrates Concrete

Epoxy Grout
2 Part Grouting Epoxy

Steel Fabricator Ballustrader Concreter Civil Contractor Factory Fitter Builder
Filling gaps under base plates 4 4 4
Filling gaps under concrete panels 4 4 4
Filling grout tubes 4 4
Grouting bridge beam supports 4 4 4
Filling under machinery baseplates 4
Anchoring rod & bar into concrete 4 4 4 4 4
Grouting supports for rails 4 4
Bonding new to old concrete 4 4 4
Installation
1. Epoxy Grout is supplied as pre-measured kits. Where practical mix total contents of each part of 2 L and 4 L kits together to avoid measuring errors
Grouts
2. Ensure concrete is free from dust or contaminants that may interfere with the bond.
3. Grit blast or scabble concrete to expose clean surface.
4. Remove ponded water. Concrete may be damp but not wet.
5. Stir the hardener and base components separately before mixing together, to disperse any settlement.
6. Pour the entire contents of the Part B container into the Part A container.
7. Mix the two components together using a suitable slow-speed mixer and high-shear mixing paddle (No Fillers: Ramset™ - Small Spiral Mixing Paddle,
with Fillers Ramset™ - Large Spiral Mixing Paddle), for 2 minutes, until a fully uniform colour is obtained.
8. Scrape the sides of the tin and continue mixing for a further 2 minutes.
Grouting:
9. Position and level baseplate
10. Construct formwork around base plate with 25 mm clearance
11. Coat formwork with a thin film of grease or other release agent to prevent permanent bond
12. Form a pouring head with minimum 150 mm above base plate level
13. Form 50 mm off-side shutter opposite pouring head to allow air and grout to escape
14. Read mixing instructions 1 to 8 above
15. Pour Epoxy Grout into the pouring hopper
16. Keep pouring until Epoxy Grout has risen in the off-side shutter
17. Allow Epoxy Grout to cure for 24 hours before stripping form work
Note: If thickness is greater than 50mm, pour Epoxy Grout in layers maximum 50mm thick.
Typical Properties of Epoxy Grout mixed with FillersFG™

Consistency Volume of Epoxy Weight of Fillers Yield of Mixture Pot Life @ 20°C Compressive Tensile Strength Flexural Strength
Grout (Litres) FG (Kg) (Litres) (Minutes) Strength @ 7 days (MPa) @ 7 days (MPa)
@ 7 days
Fluid 1 0.6 1.2 40-45 110 17 32
Pourable 1 2.3 1.9 40-50 100 15 29
Trowellable 1 2.9 2.1 60-70 90 12 26
Dry Pack 1 3.8 2.4 65-80 85 11 26
Recommended Epoxy Grout Hold Down Bolt & Reinforcing Bar Installation Guide
Parameter Minimum Maximum
Drilled Hole Diameter Threaded Rod, dh Rod / Bar diameter (db) + 2 mm 2 x db
Drilled Hole Diameter Reinforcing Bar, dh db + 5 mm 2 x db
Effective Hole Depth, h 8 x db -
Critical Edge Distance, ec 3xh -
Critical Anchor Spacing, ac 6xh -
Depth of Concrete Substrate, bm 1.25 x h -
More information on Anchoring Technology can be found in the Ramset “Specifier’s Resource Book”. Contact Ramset the concrete anchoring experts
™ ™
for a copy or contact your local Ramset™ Engineer.

Epoxy Grout
EPGRL2 Grey 2 Litre Kit 1

Epoxy Patch
2 Part Bonding & Patching Agent
Concrete Patch & Repair
VmOpliCant
Co

Epoxy Patch is a 2-part 100% solventless epoxy resin which can be used as • High flow properties – good bonding and penetration
is or with fillers to create a range of application consistencies. Epoxy Patch • Bonds to dry and damp concrete
has low viscosity to allow it to penetrate deep into cracks in concrete. • Pre-measured kits to avoid measuring errors
With fillers it is transformed into a pourable or trowellable patching and • High tensile and compressive strength
grouting compound. Epoxy Patch is tough and durable, specially formulated • Cures at temperatures down to 5°C
for strong bond to concrete, brick and block. • 100% solids epoxy – solvent free and negligible shrinkage
• High mechanical strength
• Resistant to vibration and dynamic loads
• Add graded sand to change consistency
Typical Properties
Appearance Part A: Water white clear liquid
Part B: Amber liquid
Pale amber when mixed together
Viscosity Flowable, pourable Tack free time 2 - 3 hours @ 25°C
Flammability Non flammable Mix ratio 2:1 (part A:B) by volume
Solid content by weight 100%
Min. Application temp. 5°C
Tensile strength 45 MPa approx.
Compressive strength 100MPa approx. Max. Application temp. 30°C
Flexural strength 50 MPa approx. Density 1.15 kg/Litre
Tensile bond strength 15 MPa approx. Water absorption* <0.2% (10 days at 25°C)
Modulus of elasticity 11 x 103 MPa
Service temperature -10°C to + 70°C
Min. Thickness 1.5mm
Heat distortion temp 90°C approx.
Max. Thickness 50mm
Hardness > 80 Shore D
Substrate Concrete
Pot life 20 - 33 mins @ 25°C

Epoxy Patch
2 Part Bonding & Patching Agent

Bricklayer Concreter Civil Contractor Factory Fitter Builder
Structural Repairs to
4 4 4 4 4
concrete & masonry
Bonding new to old
4 4 4 4
concrete
Patching damaged

4 4 4 4
concrete
Related Products
FillersFG™ Fine Grade Sand Filler
Installation
1. Epoxy Patch is supplied as pre-measured kits. Where practical mix total contents of each part of 1 L and 3 L kits together to avoid measuring errors
2. Ensure concrete is free from dust or contaminant that may interfere with the bond.
3. Grit blast or scabble concrete to expose clean surface.
4. Remove ponded water. Concrete may be damp but not wet.
5. If fillers are required, add correct weight to Part A and mix with Ramset™ high shear mixing paddle.
6. Pour the entire contents of the Part B container into the Part A container.
7. Mix the two components together using a suitable slow-speed mixer and high-shear mixing paddle (No Fillers: Ramset™ - Small Spiral Mixing Paddle,
with Fillers Ramset™ - Large Spiral Mixing Paddle), for 2 minutes, until a fully uniform colour is obtained.
8. Scrape the sides of the tin and continue mixing for a further 2 minutes.
Patching:
9. Remove unsound concrete by chasing and chiselling
10. Wirebrush exposed reinforcement and degrease
11. Use unfilled Epoxy Patch to prime concrete and reinforcement
12. Apply primer coat with brush or airless spray
13. Read mixing instructions 1 to 8 above
14. Apply filled Epoxy Patch when primer coat is tacky
15. Allow Epoxy Patch to cure for 24 hours before stripping form work
Note: If thickness is greater than 50mm, pour Epoxy Grout in layers maximum 50mm thick.
Typical Properties of Epoxy Patch mixed with FillersFG™

Volume of Compressive Tensile Flexural
Weight of Yield of Pot Life @
Consistency Epoxy Patch Strength @ Strength @ Strength @
Fillers FG (Kg) Mixture (Litres) 20°C (Minutes)
(Litres) 7 days (MPa) 7 days (MPa) 7 days (MPa)
Very Fluid 1 1.7 2.0 35-45 80 16 28
Fluid 1 3.4 3.0 40-50 75 14 26
Pourable 1 5.1 4.0 55-65 70 13 26
Stiff Paste 1 6.8 5.0 55-65 70 11 25
Trowellable 1 8.5 6.0 55-65 70 11 24
Dry Trowellable 1 10.2 7.0 65-70 60 10 21
Epoxy Patch
EPPHL1 Amber 1 Litre Kit 1

Epoxy Putty
2 Part Repair Putty
Features & Benefits

• Sag resistant
• High build consistency
• Suitable for filling voids with thick cross-section – low heat generated
during cure
VmOpliCant
• Trowellable
• High compressive strength
• 100% solids epoxy – solvent free and negligible shrinkage
Co • Water proof when cured
• Equal Parts Mix Ratio - Easy to use and measure

Epoxy Putty is a 2-part 100% solventless epoxy compound for repairing Brick- Concreter Civil Factory Builder Plumber Elect-
chips, cracks, spalls and other defects in concrete. Its putty like consistency layer Contractor Fitter rician
makes it ideal for repairs where a flowable compounds will not stay in place. Structural
Epoxy Patch is tough and durable specially formulated for strong bond to Repairs to
4 4 4 4 4
concrete, brick and block. concrete &
masonry
Typical Properties Filling gaps
- fixtures & 4 4 4 4 4 4
Appearance Part A: White Thixotropic Paste concrete
Part B: Black Thixotropic Paste
Mixed Colour Grey
Flammability
Solid content by weight
Non flammable
100%
Related Products
Tensile strength 30 MPa approx. Large Spiral Mixing Paddle (Mixtures greater than 4L)
Compressive strength 110MPa approx.
Flexural strength 25 MPa approx.
Tensile bond strength 10 MPa approx. Installation
Modulus of elasticity 4.5 x 103 MPa 1. Ensure surfaces are clean and dry
Service temperature -10°C to + 65°C 2. Measure equal parts of Part A and Part B onto a flat board
3. Using a spatula knead the two parts together until the colour is a
Heat distortion temp 80°C approx. uniform grey with no streaks
Hardness > 80 Shore D 4. Apply Epoxy Putty using gloved hand or spatula
5. Smooth surface with a trowel
Pot life 30 - 40 mins @ 25°C
Mix ratio 1:1 (part A:B) by volume www.ramset.com.au, for precautions and further detailed
Min. Application temp. 10°C
Max. Application temp. 35°C
Density 1.5 kg/Litre Epoxy Putty
EPPYL1 Grey 1 Litre Kit 1
Substrate Concrete, Concrete Block, Brick, Steel EPPYL2 Grey 2 Litre Kit 1

UltraFix™ConcreMate™
Non Shrink Patching Cement

Features & Benefits
• Fast Setting
• High Strength
• Durable
• Expands To Ensure Strong Bond
VmOpliCant
Co

UltraFix™ ConcreMate™ is a quick setting, high strength, shrinkage Carpenter Builder Plumber Electrician Mech Concreter
compensating cement for patching, repairing and anchoring. It is easy to Services
mix and apply and is ideal for industrial, mining and general use. Once Repairing 4 4
mixed, UltraFix™ ConcreMate™ sets in 30 minutes and cures rock hard in 1 damage to
hour. UltraFix™ ConcreMate™ expands to compensate for drying shrinkage concrete
normally found in cement based products. This prevents gaps opening up Filling gaps 4 4 4 4 4 4
between the repair and the existing concrete and promotes a strong long between
concrete &
lasting bond.
fixtures
Anchoring rod 4 4
& bar into
Typical Properties concrete
Typical Value
Property Trowellable Pourable Related Products
Water per 1 Kg 300 ml 400 ml Small Spiral Mixing Paddle (Mixtures up to 4L)
Wet Density 1900 kg / m3 1800 kg / m3 Large Spiral Mixing Paddle (Mixtures greater than 4L)
Working Time 10 minutes @ 20°C 10 minutes @ 20°C
Yield / 10 Kg Pack 6.7 L 7.7 L Installation
Yield / 25 Kg Pack 16.8 L 19.2 L 1. Ensure surfaces are clean. Remove ponded water
Trafficable 1 hour @ 20°C 1 hour @ 20°C 2. Add water to an empty container
Setting Expansion 0.2% 0.2% 3. Gradually add Ultrafix™ Concremate™ powder to water while stirring until
Net Expansion After 0.125% 0.125% desired consistency is achieved
Drying 4. Continue stirring until mixture is free of lumps
1 Hour 20 MPa 5. Protect Ultrafix™ Concremate™ from rain or evaporation using impervious
Compressive Strength plastic or similar for at least 24 hours
24 Hours 70 MPa
UltraFix™ ConcreMate™
830104 Grey 10kg Pail 1
830111 Grey 25kg Pail 1

Accessories
Mixing Paddles
Part No. Description Mixing Volume Order Qty
SSMP Small Spiral Mixing Paddle Up to 4 Litres 1
LSMP Large Spiral Mixing Paddle Greater than 4 Litres 1
Accessories
CAGU300 CAGU850 SABGU37
Applicator Guns
Part No. Description Pack Size Order Qty
CAGU300 Caulking Gun 300ml Cartridge 1
CAGU850 Caulking Gun 850ml Cartridge 1
SABGU37 Sausage Barrel Gun 600ml Sausage 1
BGUNOZ BGUNS
Nozzles For use with sealant barrel gun (SABGU37)

Part No. Description Suits Order Qty
BGUNS Mixed Nozzle Set (pack of 5) SABGU37 1
BGUNOZ Cone Nozzle Set Natural (pack of 10) SABGU37 1
Backing Rod
Part No. Description Diameter x Length Order Qty
BRPE10 Polyethylene Foam Backing Rod 10mm x 250m Roll 1
FillersFG™ Fine grade sand filler for use with Epoxy Grout and Epoxy Patch
Part No. Colour Net Weight Order Qty
RFLG Tan 20kg bag 1

Accessories
Powered Caulking Gun
Pneumatic function reduces

risk of plunger breaking the
sausage
Accessories
Weighted for comfortable
use at different angles
Description
Caulking gun for the fast application of sausage cartridges up to 600ml and
sealant cartridges up to 300ml.
Speciﬁcation
Weight (including Batteries) 2.5Kg
Battery Pack 13.2v / 3.0Ah
Batteriy Type NiMH
Max Force 1,400Nm
Max Pressure 8.5 Bar
Charging Time 60min
Noise / Vibration Information

Sound Pressure Level: 70.5dB (A)
Sound Power Level: 83.5dB (A)
Wear Eye and Ear Protection Features & Benefits
Vibration: The typical weighted acceleration does not exceed 2.5m/s2 • Pneumatic function reducing the risk of the plunger breaking the sausage
and damaging the tool
Powered Caulking Gun • Increased speed
Part No. Description Order Qty • Increased productivity
RCG600 Ramset™ Caulking Gun 1 • Weighted for comfortable use at different angles
Includes 600mm & 300mm nesting tubes, 2 x batteries, charger & plastic case. • Effortless dispensing

Builder
Metal pipe penetrations 4 4 4 4 4
Cable penetrations 4 4 4 4
Plasterboard FR wall 4 4 4 4 4 4

Notes
Notes

Sales, Orders and Enquiries
Tel: 1300 780 063
Fax: 1300 780 064
Email: [email protected]
Web: www.ramset.com.au
STATE BRANCHES
Anchoring
VICTORIA New South Wales QUEENSLAND
5/71 Victoria Crescent, Abbotsford 3067 71 Carnarvon Street, Silverwater 2128 281 Montague Road, West End 4101
296-298 Maroondah Highway, 563 Gardeners Road, Mascot 2020 153 Ingham Road, Townsville 4810
& Chemicals
HEAD OFFICE Mooroolbark 3138 3/8 Channel Road, Mayfield West 2034
296-298 Maroondah Highway
Mooroolbark, Victoria 3138 SOUTH AUSTRALIA ACT WESTERN AUSTRALIA
Tel: 03 9726 6222 115 Sir Donald Bradman Drive, 5/19 Tennant Street, Fyshwick 2609 1/12 Colin Jamieson Drive, Welshpool 6106
Hilton 5033
ITW Construction Systems Australia Pty. Ltd. ABN 48 004 297 009 trading as Ramset™. ™Trademarks of Cetram Pty. Ltd. used under licence by Ramset™ Product Catalogue
© Copyright 2010 RAM/MACACC6/2010
In the interests of product improvement, Ramset™ reserves the right to alter product specifications as required.
Information included in this Product Guide is correct at time of printing.
It is the responsibility of the user to ensure product selected is appropriate for its intended use.
For further technical information go to www.ramset.com.au or contact Ramset™ on the numbers indicated.

Ramset Anchoring Chemicals Catalogue

Uploaded by

Copyright:

Available Formats

Ramset Anchoring Chemicals Catalogue

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Ramset Anchoring Chemicals Catalogue

Uploaded by

Copyright:

Available Formats

Sales, Orders and Enquiries

Tel: 1300 780 063

Ramset™ have been offering mechanical anchors

Unlike any direct competitor, Ramset™ develops

This Product Guide is designed to provide

www.ramset.com.au 1300 780 063 3

4 www.ramset.com.au 1300 780 063

Medium Duty Anchors 17

Light Duty Anchors 31

Plasterboard & Cavity Anchors 59

Self Drilling Screws 69

www.ramset.com.au 1300 780 063 5

Types of Mechanical Anchor Types of Substrate

Setting Methods strength of the substrate.

Rotation Load Directions

Thread Forming Vibrating Load

Interference Fit Shock Load

6 www.ramset.com.au 1300 780 063

• The minimum thickness of the base material (bm) (determined by anchor

• The coincidence of stress cones of adjacent anchors in concrete reduces

Anchor Effective Depth: hef

For further information consult the Ramset™ Specifiers Resource Book.

Reduced Distance Between Anchors

For further information consult the Ramset™ Specifiers Resource Book.

www.ramset.com.au 1300 780 063 7

TruBolt™ Stud Anchors 4 ▲

4 Recommended ● Recommended with care ▲ Site tests should be implemented

8 www.ramset.com.au 1300 780 063

Heavy Duty Anchors

www.ramset.com.au 1300 780 063 9

Low profile hex or

Patented anti-rotation expansion

10 www.ramset.com.au 1300 780 063

Trades & Applications

Heavy Duty Anchors

SpaTec™ Plus Safety Anchors - Hex Bolt - Zinc Plated

SpaTec™ Plus Safety Anchors - Countersunk Head - Zinc Plated

SpaTec™ Plus Safety Anchors - Indicative Working Loads in 32MPa Concrete

www.ramset.com.au 1300 780 063 11

Low profile hex head

Depth set mark

12 www.ramset.com.au 1300 780 063

Trades & Applications

Heavy Duty Anchors

Boa™ Coil Expansion Anchors - Hex Bolt - Zinc Plated

Boa™ Coils Only - Zinc Plated

Boa™ Coil Expansion Anchors - Indicative Working Loads in 32MPa Concrete

www.ramset.com.au 1300 780 063 13

Anchor diameter Anti-rotation expansion sleeve

14 www.ramset.com.au 1300 780 063

Trades & Applications

Heavy Duty Anchors

TruBolt™ Stud Anchors - Hex Nut - Zinc Plated

www.ramset.com.au 1300 780 063 15

TruBolt™ Stud Anchors - Hex Nut - Hot Dipped Galvanised

TruBolt™ Stud Anchors - Indicative Working Loads in 32MPa Concrete

16 www.ramset.com.au 1300 780 063

Medium Duty Anchors

www.ramset.com.au 1300 780 063 17