Nitoproof 600PF

Nitoproof 600 PF constructive solutions
Pitch Free PU based Liquid applied single

component elastomeric water pr oofing
membrane.
Uses Typical results from membrane cured for 28

days:
Nitoproof 600PF is used to provide a continuous, seamless,
water and vapour proof membrane for concrete. Typical ap- Elongation (%) : > 400
plications will include roofs, podiums, balconies, floor slabs, (ASTM D412)
suspended floors, patios, bathrooms, inspection pits, swimming
Tensile Strength (N/mm2 : >1.9
pools, bridge decks. (ASTM D412)
Advantages Adhesion in-peel test (N) : > 50N

ASTM C836)
 Non-toxic formulation
Recovery from elongation (%) : 95
 Pitch free Polyurethane (ASTM D412)
Cures to form a permanently flexible, resilient barrier over Tear resistance (kN/m) : 15
ASTM D624-00
a wide range of temperatures
Water vapour transmission : 0.6
 Root Resistance* 2.3mm film (g/m2/hr)
 Excellent continuous adhesion to concrete prevents lateral Initial hardness (Shore A) : 60

water migration (ASTM 2240)
Water permeability@5 bar, mm : Nil

 Irreversible chemical cure does not permit melting or flow (BSEN 12390)
of film at elevated ambient temperautres
Chemical resistance : Unaffected by mild acids, alkalis and
 Capable of bridging substrate cracks up to 2mm water borne salts. Does not biodegrade.
 Easy to apply, requires no special equipment

* Also, available in Black colour
* Protection screed required
Specification clauses
Description
Supplier Specification
Nitoproof 600PF is a single component pitch free PU based
Where shown on the drawings, the liquid applied, elasto-
liquid polyurethane. It cures by reaction with atmospheric
meric polyurethane waterproof membrane shall be Nitoproof
moisture to form a tough, elastomeric, waterproof membrane.
600PF obtained from Fosroc. It shall be used in accordance
Nitoproof 600PF is designed for use on horizontal and vertical
with the manufacturer’s current application instructions.
surfaces, covered by a protective screed or render.
Performance Specification
Technical support
The liquid applied, elastomeric waterproofing membrane, where
Fosroc offers comprehensive technical support, including help
shown on the drawings, shall be made of hydrocarbon free
at the design stage, application advice and on site problem
polyurethane. The membrane when cured shall be capable of
solving. Specifiers and contractors are encouraged to contact
an extension of not less than 400%. Its tensile strength shall
our trained staff for answers to their questions.
exceed 1.9 N/mm2 and the water vapour transmissions shall
For further information please contact Fosroc be less than 1g/m 2/24 hour. It shall be used in accordance
with the methods given in the manufacturer’s data sheet.
Typical Properties
Application instructions
* Colour : Dark Green
Preparation
Application temperature range : 5oC to 50oC
All surfaces to be waterproofed should be clean, sound
Service temperature range : -40oC to +70oC
and dry. Priming for good quality, dense concrete is
Nitoproof 600 PF
Tack free time @ 25oC : 5 hours

not necessary. For absorbent surfaces such as po-
Specific gravity : 1.4 rous concrete a mixture of 1 part Nitoproof 600PF
Viscosity : 60p and 1 part of Nitoflor Sol is used to seal the surface.
Solids content(%) : 85
page 1 of 4
Nitoproof 600PF
Cracks
Storage
Shrinkage and non-moving cracks should be pre-treated with not Shelf life
less than 1.5 mm coating of Nitoproof 600PF extending 75mm
either side of the crack. Allow to cure before general application. Minimum 9 months in original unopened containers if kept
below 25oC.
Right Angle Bends
Note : In accordance with Commercial or Health & Safety
All critical right angle bends must have a minimum 25 x 25mm requirements packaging detail may alter. Please contact your
angle fillet installed prior to application of Nitoproof 600PF. All local Fosroc office for detail.
angle joints, protrusions and stress points should be pretreated
Precautions
with heavy application of Nitoproof 600PF extending 50 -100mm
either side of the detail. Any pretreated areas must be cured Health and safety
overnight before general application of the membrane.
Some people are sensitive to resin systems. Impervious gloves
Application Methods and barrier cream should be used when handling these
products. Eye protection should be worn. If accidental eye
Nitoproof 600PF can be applied by brush, squeegee or roller. It is
contamination occurs, wash thoroughly with plenty of water
applied at a minimum wet film thickness of 1.5mm in 2 coats. The
and seek medical advice. If contact with skin occurs, it must be
second coat should be applied in perpendicular direction to the
removed before curing takes place. Wash off with an industrial
first coat. Where required, Nitoproof 600PF may be reinforced
skin cleaner followed by plenty of soap and water. Do not use
using a suitablefabric reinforcement. This should be applied to
solvent. Ensure adequate ventilation when using these products.
a 1.5mm application of Nitoproof 600PF whilst it is still wet and
be overcoated with another 1.5mm thick application 24 hours Fire
later. Please contact your local Fosroc office for details.
Nitoproof 600PF is flammable. Keep away from sources of
The newly applied membrane must be allowed to cure for a ignition. No smoking. In the event of fire, extinguish with CO2
minimum 24 hours at 25°C. Tools and equipment should be or foam. Do not use a water jet.
clean with suitable solvent immediately after use.
Flood Test
Flash point: 56 oC
Prior to placement of protection, flood to a minimum depth of
50mm of water for 24 hours. Drains shall be plugged and bar-
riers placed to contain the water. For further information, refer to the Product Material Safety
Datasheet.
Cleaning
Tools and equipment should be cleaned with a suitable solvent

immedaitely after use. Do not use the solvent for thinning.
Limitations
Nitoproof 600PF should be protected from UV light not more

than 14 days after application. This can normally be achieved
by use of a protective screed.
Estimating
Supply
Nitoproof 600PF : 25 kg pails
Coverage : 2.0 kg/m 2 for 1.5mm wet

film thickness
constructive solutions page 2 of 4

Nitoproof 600PF
Important note :
Fosroc products are guaranteed against defective materials and manufacture and are sold
subject to its standard terms and conditions of sale, copies of which may be obtained on
request. Whilst Fosroc endeavours to ensure that any advice, recommendation specification
or information it may give is accurate and correct, it cannot, because it has no direct or
continuous control over where or how its products are applied, accept any liability either
directly or indirectly arising from the use of its products whether or not in accordance with
Fosroc Chemicals any advice, specification, recommendation or information given by it.
(India) Pvt. Ltd.
Head Office
Embassy Point telephone fax e-mail
No.150, 2nd Floor,
++91 80-42521900 ++91 80-22281510 [email protected]
Infantry Road,
Bangalore-560001
Regional Offices
Chennai Mumbai Noida Kolkata

Hills Center, Old No.5, New No.9 MBC Park, 12th floor, Office No.12B, Unit No. 601, Highway Tower-II 304, Jodhpur Park
3rd Cross Street, Jeth Nagar, ‘D’ Block, Near G Corp/Hyper City A-13/2, 6th Floor, Sector– 62 Kolkata 700 068
Raja Annamalaipuram, Kasarwadawali, Ghodbunder Road, Gautam Buddha Nagar, Ph:+91 33-65343188
Chennai 600 028 Thane (West) 400 615 Noida 201 309, Uttar Pradesh Fax: 033-2499-0280
Ph: +91 44 24899949-94 Ph: +91 22 6229 6800 Ph: +91 120 6121900
Fax: 044-24896641 Fax: 022 62296809
www.fosroc.com INDIA/2019/0941/C
page 3 of 4

Nitoproof 600PF

Uploaded by

Copyright:

Available Formats

Nitoproof 600PF

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Nitoproof 600PF

Uploaded by

Copyright:

Available Formats

Nitoproof 600 PF constructive solutions

Pitch Free PU based Liquid applied single

Uses Typical results from membrane cured for 28

Advantages Adhesion in-peel test (N) : > 50N

 Excellent continuous adhesion to concrete prevents lateral Initial hardness (Shore A) : 60

Water permeability@5 bar, mm : Nil

 Easy to apply, requires no special equipment

Tack free time @ 25oC : 5 hours

Tools and equipment should be cleaned with a suitable solvent

Nitoproof 600PF should be protected from UV light not more

Nitoproof 600PF : 25 kg pails

Coverage : 2.0 kg/m 2 for 1.5mm wet

constructive solutions page 2 of 4

Chennai Mumbai Noida Kolkata

You might also like