Chapter 10 :

Computer Science
Class XII ( As per
CBSE Board) Network
device
and
functions
New
Syllabus
2019-20

Visit : python.mykvs.in for regular updates

Network devices
Computer hardware devices which are used to
connect computers, printers, or any other
electronic device to a computer network are
called network devices. These devices transfer
data in a fast, secure and correct way with
some specific functionality over same or
different networks.

Some devices are installed on the device, like

Internal modem, NIC card or RJ45 connector,
whereas some are part of the network, like
router, switch, etc.

Visit : python.mykvs.in for regular updates

 Network devices
NIC – This is at top among other networking devices and mostly used
networking device. This is also known as network adapter card, Ethernet Card
and LAN card. It allows our PC to communicate with other PCs. A PC uses
parallel data transmission to transmit data between its internal parts where as
the media that connects this PC with other device/PCs uses serial data
transmission. A NIC converts parallel data stream into serial data stream and
vice versa.

Visit : python.mykvs.in for regular updates

 Network devices
NIC –
Usually all modern PCs have inbuilt NICs in motherboard. NICs are also
available separately in adapter format which can be plugged into the available
slots of motherboard. For laptop or other small size devices they available in
PCMCIA (Personal Computer Memory Card International Association) card
format which can be inserted in PCMCIA slots.
Types of NICs
• Media Specific :- Different types of NICs are available for establishing
connection with different types of media. For e.g. we cannot connect
wireless media with wired NIC card or vice versa. similarly we can’t connect
coaxial cable with Ethernet LAN card. So we have to use specific NIC,
which is best suited for particular media .
• Network Design Specific :- FDDI, Token Ring or Ethernet have their own
distinctive type of NICs card. NIC can’t be used interchangeably.

Visit : python.mykvs.in for regular updates

 Network devices
HUB – HUB is used to connect multiple computers in a single LAN network of one
workgroup. Generally HUBs are available with 4,8,12,24,48 ports.
When a hub receives signal on its port, it repeats the signal and forwards that signal
from all ports except the port on which the signal arrived. In below diagram leftmost
node try to send signal to rightmost node ,but signals are distributed to all
ports(nodes).
There are two types of HUB
Passive HUB:- It only forwards the
signal on all ports without amplifying the
signal.
Active HUB:- it forwards the signal with
improvement in the quality of data
signal by amplifying it. That why such
hubs need additional power supply.
Based on port type, there are two types
of HUB:-
Ethernet HUB :- All ports have RJ-45
connectors.
Combo HUB :- Several different types
of connectors such RJ-45, BNC, and
AUI available as ports in such HUB.
Visit : python.mykvs.in for regular updates
 Network devices
SWITCH –Switch is also used to connect multiple computers together in a
LAN workgroup,just like hub. Switches are available with 4,8,12,24,48,64
ports. Switch makes their switching decisions by using application specific
integrated circuits (ASICs).Due to switching decision capability, switch sends
signal to recipient only and that’s why switches are called as intelligent hub.
In below diagram leftmost node sending signal to rightmost node.

Visit : python.mykvs.in for regular updates

 Network devices
Repeater – In a network signal travels a long distance in transmission media.
Due to resistance of media signal becomes weak. Repeater is a networking
device which regenerates the signal and forwards these signal with more
power.

Visit : python.mykvs.in for regular updates

 Network devices
Router – Routers operate in the physical, data link
and network layers. Router is a networking device
which chooses the best optimal path from
available pats to send the signals. It interconnects
different networks. The simplest function of a
router is to received packets from one connected
network and pass them to second connected
network.

Gateway – A networking device capable to

convert protocols so that two different network
architecture based system can communicate with
each other.It works as protocol convertor.
Visit : python.mykvs.in for regular updates
 Network devices
Access Point – Also known as wireless access point. An
access point is a station which transmits and receives data
(transceiver). It connects users to other users within the network and
also can serve as the point of interconnection between the WLAN and
a fixed wire network.

Visit : python.mykvs.in for regular updates

 Network devices
Network stack – It's a sub-system in a computer that deals with networking.
In most computers it is TCP/IP stack but there are number of other protocols also.
Computer programs only need to know about an IP address or hostname, a tcp or udp
port number and the network stack takes care of forming this in standardized packets
on the network to send the data towards remote system. The reverse action is done at
the receiving end. This can be understood by given diagram.

Data delivered on host computer

----Network stack----
by any of application protocol e.g.
http,ftp to transport layer where
tcp Works,which makes packets of
these data and deliver to network
Layer ip protocol,which create Ip
datagram,at interface these are
Known as network frames.These
packets move over the media and
reverse action is performed at next
computer.

Visit : python.mykvs.in for regular updates

 Network devices
Modem – Modem is short for Modulator Demodulator. It’s
an electronic device used to access the Internet that
modulates carrier waves to encode information to be
transmitted and also demodulates incoming carrier waves
to decode the information they carry.
Modulation means digital to analog signal conversion and
its vice versa is known as demodulation.

Visit : python.mykvs.in for regular updates

 Computer Networking
Two common modulation techniques are
1. Amplitude modulation
2. Frequency modulation

1-Amplitude modulation
Amplitude-the maximum displacement or distance moved by
a point on a vibrating body or wave measured from
its equilibrium position. It is equal to one-half the length of
the vibration path.

Visit : python.mykvs.in for regular updates

 Computer Networking
1 - Amplitude modulation
Amplitude Modulation, in short AM, is
a common method of broadcasting
radio signals. Discovered in 1870s,
that information in the form of audio
can be broadcast over long distances
through radio waves.
In AM, the amplitude of the carrier
wave is modified in order to transmit
the input signal.
The amplitude of the carrier wave
varies proportionally according to the
input signal, so when the input signal
has a low amplitude, the amplitude of
the carrier wave is decreased and
vice-versa.

Visit : python.mykvs.in for regular updates

 Computer Networking
2 - Frequency modulation
Frequency Modulation, in short FM.In FM, the instantaneous
frequency of the carrier wave is altered according to the
amplitude of the input signal.

Due to the much better transmission quality, most music radio

stations prefer FM over AM to transmit information (mostly,
songs) to their listeners.

Visit : python.mykvs.in for regular updates

 Computer Networking
Collision in wireless networks - Collisions occur on a
network when two or more networked devices transmit data at the same
time. The result is that the data collides, becomes corrupted, and needs
to be re-sent.

Using CSMA/CD(Carrier Sense multiple access/Collision detection), if a

collision is detected on the medium, end-devices would have to wait a
random amount of time before they can start the retransmission
process. For this reason, CSMA/CD works well for wired networks,
however, in wireless networks, there is no way for the sender to detect
collisions the same way CSMA/CD does.

Therefore, CSMA/CA is used on wireless networks. CSMA/CA doesn’t

detect collisions (unlike CSMA/CA) but rather avoids them through the
use of a control message. Should the control message collide with
another control message from another node, it means that the medium
is not available for transmission and the back-off algorithm needs to be
applied before attempting retransmission.
Visit : python.mykvs.in for regular updates
 Computer Networking
Collision in wireless networks –
• Hidden node problem
Node A and C send the signal to B at the
same time and collision occurs at Node B
this can’t be detected so CSMA/CA scheme
can be used here to avoid collision here.

• Exposed Node problem

Here if c want to transmit signal to b but
knows that collision can occur so if needed
can transmit the signal to d. such solution is
possible with Multiple Access with Collision
Avoidance (MACA) scheme.
Sender transmits Request to Send
(RTS) frame to receiver . The receiver then
replies with clear to send (CTS) frame back
to the sender as it is busy.if such CTS frame
is not received then sender comes to know
that receiver is free to send data.
Visit : python.mykvs.in for regular updates
 Computer Networking
How CSMA/CA Works start

The station ready to transmit signal, senses Set back

to 0
the line by persistent strategies.
• As soon as it find the line to be idle, the
Persistent
station waits for an IFG (Interframe gap) strategy
amount of time.
• If then waits for some random time and Wait IGF
sends the frame. time
• After sending the frame, it sets a timer and
Wait random
waits for the acknowledgement from the time
receiver.
• If the acknowledgement is received before Send the
expiry of the timer, then the transmission is frame
Wait for
successful. backoff time
• But if the transmitting station does not Set a timer

receive the expected acknowledgement no

before the timer expiry then it increments the
back off parameter, waits for the back off Back Increment ACK
off time backoff before
time and resenses the line. time out
yes yes
abort success

Visit : python.mykvs.in for regular updates

 Computer Networking
How MACA Works

• Sender sends a request to send (RTS) frame containing

the length of transmission
• Receiver respond with clear to send (CTS) frame
• Sender sends data
• Receiver sends ACK,now another sender can send data
• When sender do not get a CTS back ,it is assumed that
collision occurs
Visit : python.mykvs.in for regular updates
 Computer Networking
Error checking –
Networks must be able to transfer data from one device to another with
complete accuracy. Data can be corrupted during transmission. For
reliable communication, errors must be detected and corrected.

Parity Bit
A single bit is appended to each data chunk that makes the number of
1 bits even/odd.

Example: even parity

1000000(1)
1111101(0)
1001001(1)
Example: odd parity
1000000(0)
1111101(1)
1001001(0)

Visit : python.mykvs.in for regular updates

 Computer Networking
Error checking –
Single dimension parity check
Suppose the sender wants to send the word word. In ASCII the four
characters are coded as
1110111 1101111 1110010 1100100
The following shows the actual bits sent in case Even parity is used:
11101110 11011110 11100100 11001001

Now suppose the word word in Example 1 is received by the receiver

without being corrupted in transmission.
11101110 11011110 11100100 11001001
The receiver counts the 1s in each character and comes up with even
numbers (6, 6, 4, 4). The data are accepted.
Visit : python.mykvs.in for regular updates
 Computer Networking
Error checking –
Now suppose the word word in Example 1 is corrupted during
transmission.
11111110 11011110 11101100 11001001
The receiver counts the 1s in each character and comes up with even
and odd numbers (7, 6, 5, 4). The receiver knows that the data are
corrupted, discards them, and asks for retransmission.

Visit : python.mykvs.in for regular updates

 Computer Networking
Error checking –
Two dimensional parity checking - Performance can be improved by
using two-dimensional parity check, which organizes the block of bits
in the form of a table. Parity check bits are calculated for each
row,which is equivalent to a simple parity check bit. Parity check bits
are also calculated forall columns then both are sent along with the
data.

Visit : python.mykvs.in for regular updates

 Computer Networking
MAC Address–A MAC address is the unique identifier that is
assigned by the manufacturer to a piece of network hardware (like a
wireless card or an Ethernet card).
A MAC address is made up of six two-digit hexadecimal number ,
each separated by a colon.
00:1B:f4:11:fA:B7 is an example of a MAC address.
Manufacturer id Card no
How do I find my device’s MAC address?
• Click Windows Start or press the Windows key.
• In the search box, type cmd.
• Press Enter
• A command window displays.
• Type ipconfig /all and Press Enter.
• A Physical Address displays for each adapter. The Physical
Address is your device’s MAC address.
Steps for finding MAC address depends on the OS being used.

Visit : python.mykvs.in for regular updates

 Computer Networking
IP Address – An IP address is a number which is used to
identify any device on a network. This is an important
concept as devices communicate with each other across
the LAN and WAN based on IP addresses.

IP address is a logical address which is in the format of

a.b.c.d i.e. using four octets.

An example of IP address is: 192.168.10.1

There are two types of version for IP addresses:

1. IPv4 which is 32 bits
2. IPv6 which is 128 bits

Visit : python.mykvs.in for regular updates

 Computer Networking
IPv4 –IPv4 (Internet Protocol Version 4) is the fourth revision of
the Internet Protocol (IP) used to identify devices on a network
through an addressing system. IPv4 is the most widely deployed
Internet protocol used to connect devices to the Internet. IPv4
uses a 32-bit address scheme allowing for a total of 2^32
addresses. 32 binary bits are broken into four octets (1 octet = 8
bits)Dotted decimal format (for example, 172.16.81.100)
The public address space is divided into five classes:

Class D addresses are used for multicast traffic. These

addresses are not assignable. Class E addresses are reserved
for experimental usage and are not assignable.
Visit : python.mykvs.in for regular updates
 Computer Networking
IPv6 –A new Internet addressing system Internet Protocol version 6 (IPv6) is
being deployed to fulfill the need for more Internet addresses.IPv6 is also
called IPng (Internet Protocol next generation)IPv6 is the successor to Internet
Protocol Version 4 (IPv4). IPv6 is designed to allow the Internet to grow
steadily, both in terms of the number of hosts & total amount of data traffic
transmitted.It is under development from 1990.
An IPv6 address is represented as eight groups of four hexadecimal digits,
each group representing 16 bits (two octets,known as hextet). The groups are
separated by colons (:). An example of an IPv6 address is:
2001:0db8:85f3:0000:0000:8f2e:0370:7334
The Benefits of IPv6
• No more NAT (Network Address Translation)
• Simplified, more efficient routing
• Better multicast routing
• Auto-configuration
• No more private address collisions
• Simpler header format
• True quality of service (QoS), also called "flow labeling"
• Built-in authentication and privacy support
• Flexible options and extensions
• Easier administration (say good-bye to DHCP)
Visit : python.mykvs.in for regular updates
 Computer Networking
Routing –Routing is a process which is used to deliver the packet
by choosing an optimal path from one network to another. Static
routing is a process in which we have to manually add routes in
routing table.
A routing table is a set of rules/viewed in table format is used to
determine where data packets traveling on (IP) network will be directed.
All IP-enabled devices, including routers and switches, use routing
tables.
Routing table contains routing entries, that is list of destinations (often
called: list of network prefixes or routes)
Where to route to 192.168.1.30?
From the routing table below
192.168.1.10/32 via 10.254.2.1
192.168.1.30/24 via 10.254.3.1
192.168.1.20/32 via 10.254.2.1
Having the destination IP of packet, routers always choose best
matching ROUTING ENTRY. That means LONGEST PREFIX MATCH.
This means that in our case entry: 192.168.1.30/24 is more accurate
that 192.168.1.10/32 in the search for 192.168.1.30.
Visit : python.mykvs.in for regular updates
 Computer Networking
DNS –The Domain Name System, translates human readable
domain names (for example, www.python.mykvs.in) to machine
readable IP addresses (for example, 182.156.84.26). ... DNS
servers translate requests for names into IP addresses.

Request python.mykvs.in
Response 182.156.84.26

Local DNS server

Make http Request to 182.156.84.26

Http response
A domain name is our website name. e.g. in python.mykvs.in , in
is primary domain,mykvs is subdomain of in and python is
subdomain of mykvs.
Generic domain name - .com,.edu,.gov,.mil,.net,.org etc
Country specific domain name - .in for india,.us for united states
Visit : python.mykvs.in for regular updates
 Computer Networking
URL –Uniform Resource Locator is defined as the global
address of documents and other resources on the World Wide
Web. The URL is an address that sends users to a specific
resource online, such as a webpage, video or other document or
resource.
e.g.
http://python.mykvs.in/syllabus/cs12.pdf

protocol subdomain domain name path

Visit : python.mykvs.in for regular updates

 Computer Networking
TCP –The Transmission Control Protocol
(TCP) is a connection-
oriented reliable protocol. It provides a
reliable transport service between end
Systems (ES) using the network layer service
provided by the IP protocol. TCP protocol
exchange streams of data. Individual bytes of
data are placed in memory buffers and
transmitted by TCP in transport Protocol Data
Units.
TCP Retransmission is a process of
retransmitting a TCP segment. TCP
Retransmission occurs when time out timer
expires before receiving the
acknowledgement or 3 duplicate
acknowledgements are received from the
receiver for the same segment.

Visit : python.mykvs.in for regular updates

 Computer Networking
Rate modulation –Symbol rate /baud rate/modulation rate
is the number of symbol / signaling changes during
transmission per time unit .it is measured in
baud(Bd)/symbol per second.

Rate modulation in congestion

Congestion occurs when the number of packets being
transmitted through the network approaches the packet
handling capacity of the network.
Whenever there is a timeout, TCP assumes congestion in
the network and starts to reduce its sending rate.
If the sending rate is G at a wireless link with packet loss
rate p, the throughput of this link is S = G(1 − p). TCP
should increase its sending rate G to get a large throughput
if there is no congestion, rather than decreasing its rate

Visit : python.mykvs.in for regular updates

 Computer Networking
Protocols –
1G – The analog 1G offered simple telephony service without data.
2G – Delivered digital signal and offered up to 250Kbps speed. Supports
voice, text and data services.
3G – At least 200Kbps up to 3Mbps speed.
4G – 4G delivers up to 100Mbps for mobile access, and up to 1Gbps for
wireless access. Most wireless carriers offering HSPA (High Speed Packet
Access) at up to 6Mbps are claiming that they offer 4G network.

WiFi is a connection standard provided by a wireless network. A wireless

network is in turn provided by any other any other device that connects into
another Internet access, which is typically a physical line but can be 3G. That
device then translates its own Internet connection into a WiFi network that
other devices can share.
WiFi networks are small and typically only allow up to 30 devices to connect.
They can be private, in which case we need to know a password to have
access, or they can be an open, public “hotspot,” allowing any device with
WiFi capabilities to log in.

Visit : python.mykvs.in for regular updates

 Computer Networking
What makes a protocol have higher bandwidth-
Each type of phone connection, 2G, 3G, and 4G have different
frequency range that cell phones have to be designed to use to
make and receive calls, and make a data connection. 2G has
only 4 bands, typically 3G has 5 bands, and 4G has about 7
different bands.
In telecommunication, a band is a specific range of frequencies
in the radio frequency (RF) spectrum, which is divided among
ranges from very low frequencies (vlf) to extremely high
frequencies (ehf). Each band has a defined upper and lower
frequency limit. Because two transmitters sharing the same
frequency band cause mutual interference, band usage is
regulated. International use of the radio spectrum is regulated
by the International Telecommunication Union (ITU). So
protocols(2g,3g,4g..) higher bandwidth depends on the use of
frequency band.
Visit : python.mykvs.in for regular updates