Juniper Questions

1) You are performing the initial configuration of an srx series device.
What must you

set before the device will allow you to commit your configuration?
1. management interface
2. hostname
3. root authentication
4. system time
Answer 3
2) Which statement is true about PFEs?
1. A PFE receives hardware status messages from the RE

2. A PFE receives microcode updates from the RE.
3. A PFE receives environmental status messages from the RE.
4. D. A PFE receives Layer 4 forwarding table updates from the RE
Correct Answer: 2
3) You suspect a duplicate mac address on subnet. You want to display the mac, errors,
and statistics of the ge-0/0/0 interface Which command will accomplish this task?
1. show ethernet-switching table

2. show interface terse
3. show interface ge-0/0/0 extensive
4. Show arp
Correct Answer: 3
4) Which two statements describe the default behavior for OSPF? (Choose two )
1. OSPF imports all routes into the inet4.0 routing table

2. OSPF imports all routes into the inet.0 routing table
3. OSPF does not export static routes into the OSPF database
4. OSPF exports all static routes into the OSPF database Correct
Answer: 2 and 3
5) What is the default firewall filter behavior when a term is matched but no
terminating action is specified?
1. an implicit deny and the filter evaluation continues to the next term
2. an implicit accept and the filter evaluation terminates
3. an implicit accept and the filter evaluation continues to the next term
4. an implicit deny and the filter evaluation terminates
Correct Answer: 2
6) You have configuration groups applied on your router. Which command would you
use to see all components of the interface hierarchy?
1. show configuration interfaces | display inheritance

2. show configuration interfaces | display detail
3. show configuration interfaces | display changed
4. show configuration interfaces | display set
Correct Answer: 1
7) referring to the exhibit, what does proxy ARP allow?
1. the internal network to ARP for the internal address of the server
2. the external network to ARP for the internal address of the server
3. the internal network to ARP for the public address of the server
4. the external network to ARP for the public address of the server
Answer: 1
8)Which two statements are correct about the inet.0 routing table?(choose two)
1. It is used for populating the forwarding policy.

2. It stores information learned from routing protocols and other sources
3. It is used for populating the Ethernet switching table
4. it is used for populating the forwarding table
Correct Answer: 2 and 4
9) The marketing team needs access to server on subnet 172.0.48.0/24 the next-hop
router is 10.0.4.2/30 .
A static route on their gateway has been configured to accomplish the task you want
to keep the static route from being redistributed into dynamic routing protocols.
Which command will satisfy this requirement?
1. set routing-options static route 172.0.46.0/24 next-hop 10.0.4.2/30 no-
redistribute
2. set routing-options static route 172.0.46.0/24 next-hop 10.0.4.2/30 no-resolve
3. set routing-options static route 172.0.46.0/24 next-hop 10.0.4.2/30 no
readvertise
4. set routing-options static route 172.0.46.0/24 next-hop 10.0.4.2/30
Correct Answer: 3
10) Which statement is correct about the configuration shown in the exhibit?
1 Both voice and data traffic are tagged on ge-0/0/0.
2 Voice traffic is tagged on ge-0/0/0, whereas data traffic is not.
3 Data traffic is tagged on ge-0/0/0, whereas voice traffic is not.
4 Neither voice nor data traffic is tagged on ge-0/0/0.
Correct Answer: 2
11) Which two statements about the junos os are true? (choose two)
1. it supports xml for automation on all platforms

2. it uses a different software source code base for each platform
3. it uses the same software source code base for all platforms
4. it supports java for automation on all platforms

12)A network with five switches has been configured to run Rapid Spanning Tree
Protocol (RSTP) with default settings. How many seconds does it take to detect a failure
between two neighboring switches?
1. 2 sec
2. 3 sec
3. 10 sec
4. 6 sec
Answer 4
13) Which two statements are true about a unified ISSU? (Choose two.)
1. It requires that Bidirectional Forwarding Detection be disabled.

2. It requires that graceful Routing Engine switchover be enabled.
3. It is only supported on platforms with redundant control planes.
4. It is only supported on platforms with redundant power supplies
14) When load balancing is configured on a Junos device using the load-balance per-
packet parameter, which three parameters are used to distinguish traffic flows?
1. incoming interface
2. destination address
3. destination port
4. source address
5. source port
Answer 1, 2 and 4
15) An EBGP session sources its TCP connection from which IP address?
1. The IP address of the primary address assigned to the loopback interface.

2. The IP address assigned as the router ID.
3. The IP address of the interface that connects the two BGP speakers.
4. The IP address of the preferred address assigned to the loopback interface.
Correct Answer: 3
16) Which command prompt indicates that you are in operational mode?
1. user@ router#
2. user@router%
3. user@router>
4. user@router&
Correct Answer: 3
17) Which two commands will provide the current configuration of the mx1-pe1 bgp
group on your router? (choose two)
1. user@router# show | display set | match mx1-pe1

2. user@router> show configuration | match set | match mx1-pe1
3. user@router> show configuration | display set | match mx1-pe1
4. user@router# show groups | display set | match mx1-pe1
18) Which command allows you to view the raw packet data of interface ge-1/0/5?
1. show interface ge-1/0/5 media

2. monitor traffic interface ge-1/0/5
3. show interface ge-1/0/5 extensive
4. monitor interface traffic ge-1/0/5
Correct Answer: 2
19) Which statement is true about default route prefeneces?
1. Ibgp is lower than ebgp

2. Rip is lower than ripng
3. Direct is lower than static
4. Ospf as external is lower than ospf internal
Correct Answer: 3
20)What are the maximum number of redundancy groups that would be used on a
chassis cluster?
1. The maximum number of redundancy groups use is equal to the number of

configured physical interfaces.
2. The maximum number of redundancy groups use is equal to one more than the
number of configured physical interfaces.
3. The maximum number of redundancy groups use is equal to the number of

configured logical interfaces.
4. The maximum number of redundancy groups use is equal to one more than the
number of configured
Answer 3

Juniper Questions

Uploaded by

Copyright:

Available Formats

Juniper Questions

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Juniper Questions

Uploaded by

Copyright:

Available Formats

1) You are performing the initial configuration of an srx series device.

What must you

2) Which statement is true about PFEs?

1. A PFE receives hardware status messages from the RE

1. show ethernet-switching table

1. OSPF imports all routes into the inet4.0 routing table

1. show configuration interfaces | display inheritance

7) referring to the exhibit, what does proxy ARP allow?

1. It is used for populating the forwarding policy.

Correct Answer: 2 and 4

1 Both voice and data traffic are tagged on ge-0/0/0.

2 Voice traffic is tagged on ge-0/0/0, whereas data traffic is not.

3 Data traffic is tagged on ge-0/0/0, whereas voice traffic is not.

4 Neither voice nor data traffic is tagged on ge-0/0/0.

1. it supports xml for automation on all platforms

Correct Answer: 1 and 3

1. It requires that Bidirectional Forwarding Detection be disabled.

Correct Answer: 2 and 3

1. The IP address of the primary address assigned to the loopback interface.

1. user@router# show | display set | match mx1-pe1

Correct Answer: 1 and 3

1. show interface ge-1/0/5 media

19) Which statement is true about default route prefeneces?

1. Ibgp is lower than ebgp

1. The maximum number of redundancy groups use is equal to the number of

3. The maximum number of redundancy groups use is equal to the number of

You might also like