Steam and Gas Turbines

MODULE 3: STEAM AND REACTION TURBINE

3.1 Introduction:
Steam and gas turbines are power generating machines in which the pressure energy of the
fluid is converted into mechanical energy. This conversion is due to the dynamic action of fluid
flowing over the blades. These blades are mounted on the periphery of a rotating wheel in the radial
direction. Today the steam turbine stands as one of the most important prime movers for power
generation. It converts thermal energy into mechanical work by expanding high pressure and high
temperature steam. The thermal efficiency of steam turbine is fairly high compared to steam engine.
The uniform speed of steam turbine at wide loads makes it suitable for coupling it with generators,
centrifugal pumps, centrifugal gas compressors, etc.
3.2 Classification of Steam Turbines:
Based on the action of steam on blades, steam turbines are classified into impulse turbines and
reaction turbines (or impulse reaction turbines).
3.2.1 Impulse Steam Turbine: Impulse or impetus means sudden tendency of action without reflexes.
A single-stage impulse turbine consists of a set of nozzles and moving blades as shown in figure 3.1.
High pressure steam at boiler pressure enters the nozzle and expands to low condenser pressure in the
nozzle. Thus, the pressure energy is converted into kinetic energy increasing the velocity of steam. The
high velocity steam is then directed on a series of blades where the kinetic energy is absorbed and
converted into an impulse force by changing the direction of flow of steam which gives rise to a
change in momentum and therefore to a force. This causes the motion of blades. The velocity of steam
decreases as it flows over the blades but the pressure remains constant, i.e. the pressure at the outlet
side of the blade is equal to that at the inlet side. Such a turbine is termed as impulse turbine.
Examples: De-Laval, Curtis, Moore, Zoelly, Rateau etc.

Fig. 3.1 Impulse turbine

Page | 1
Steam and Gas Turbines

3.2.2 Impulse Reaction Steam Turbine: In the impulse reaction turbine, power is generated by the
combination of impulse action and reaction by expanding the steam in both fixed blades (act as
nozzles) and moving blades as shown in figure 3.2. Here the pressure of the steam drops partially in
fixed blades and partially in moving blades. Steam enters the fixed row of blades, undergoes a small
drop in pressure and increases in velocity. Then steam enters the moving row of blades, undergoes a
change in direction and momentum (impulse action), and a small drop in pressure too (reaction),
giving rise to increase in kinetic energy. Hence, such a turbine is termed as impulse reaction turbine.
Examples: Parson, Ljungstrom etc.

Fig. 3.2 Impulse reaction turbine

3.3 Difference between Impulse and Reaction Turbines:
The differences between impulse and reaction turbines are as follows:
Impulse Turbine Reaction Turbine
✓ Complete expansion of the steam take place in ✓ Partial expansion of the steam takes place in
the nozzle, hence steam is ejected with very the fixed blade (acts as nozzle) and further
high kinetic energy. expansion takes place in the rotor blades.
✓ Blades are symmetrical in shape. ✓ Blades are non-symmetrical in shape, i.e.
aerofoil section.
✓ Pressure remains constant between the ends of ✓ Pressure drops from inlet to outlet of the
the moving blade. Hence relative velocity moving blade. Hence relative velocity
remains constant i.e., 𝑉𝑟1 = 𝑉𝑟2 increases from inlet to outlet i.e., 𝑉𝑟2 > 𝑉𝑟1
✓ Steam velocity at the inlet of machine is very ✓ Steam velocity at the inlet of machine is
high, hence needs compounding. moderate or low, hence doesn’t need
compounding.
✓ Blade efficiency is comparatively low. ✓ Blade efficiency is high.

Page | 2
Steam and Gas Turbines

✓ Few number of stages required for given ✓ More number of stages required for given
pressure drop or power output, hence machine pressure drop or power output, hence machine
is compact. is bulky.
✓ Used for small power generation. ✓ Used for medium and large power generation.
✓ Suitable, where the efficiency is not a matter of ✓ Suitable, where the efficiency is a matter of
fact. fact.

3.4 Need for Compounding of Steam Turbines:

Question No 3.1: What is the need for compounding in steam turbines? Discuss any two methods of
compounding. (VTU, Jul/Aug-05, Dec-03/Jan-07, Dec-09/Jan-10, Dec-13/Jan-14)
Answer: If the steam pressure drops from boiler pressure to condenser pressure in a single stage, exit
velocity of steam from the nozzle will become very high and the turbine speed will be of the order of
30,000 rpm or more. As turbine speed is proportional to steam velocity, the carryover loss or leaving
loss will be more (10% to 12%). Due to this very high speed, centrifugal stresses are developed on the
turbine blades resulting in blade failure. In order to overcome all these difficulties it is necessary to
reduce the turbine speed by the method of compounding. Compounding is the method of reducing
blade speed for a given overall pressure drop.
3.5 Methods of Compounding of Steam Turbine:
Question No 3.2: What are the various methods of compounding of steam turbines? Explain any
one of them. (VTU, Jul/Aug-02)
Answer: Following are the methods of compounding of steam turbines:
1. Velocity compounding
2. Pressure compounding
3. Pressure and velocity compounding
3.5.1 Velocity Compounding:
Question No 3.3: Explain with the help of a schematic diagram a two row velocity compounded
turbine stage. (VTU, Jan/Feb-05, Jul-03, Dec-12)
Answer: A simple velocity compounded impulse turbine is shown in figure 3.3. It consists of a set of
nozzles and a rotating wheel fitted with two or more rows of moving blades. One row of fixed blades
fitted between the rows of moving blades. The function of the fixed blade is to direct the steam coming
from the first row of moving blades to the next row of moving blades without appreciable change in
velocity.
Steam from the boiler expands completely in the nozzle, hence whole of the pressure energy converts
into kinetic energy. The kinetic energy of steam gained in the nozzle is successively absorbed by rows

Page | 3
Steam and Gas Turbines

of moving blades and steam is exited from the last row axially with very low velocity. Due to this, the
rotor speed decreases considerably. The velocity compounded impulse turbine is also called the Curtis
turbine stage.

Fig. 3.3 Two stage velocity compounded impulse turbine.

3.5.2 Pressure Compounding:
Question No 3.4: Explain briefly a two stage pressure compounded impulse turbine and show the
pressure and velocity variations across the turbine. (VTU, Jul-07, May/Jun-10, Dec-12)
Answer: If a number of simple impulse stages arranged in series is known as pressure compounding.
The arrangement contains one set of nozzles (fixed blades) at the entry of each row of moving blades.
The total pressure drop doesn’t take place in the first row of nozzles, but divided equally between all
the nozzles as shown in figure 3.4.

Fig. 3.4 Two stage pressure compounded impulse turbine.

Page | 4
Steam and Gas Turbines

The steam from the boiler is passed through the first set of nozzles in which it is partially
expanded. Steam then passes over the first row of moving blades where almost all its velocity is
absorbed. This completes expansion of steam in one stage. In the next stage, steam again enters the
second set of nozzles and partially expands and enters the moving blades. Again the steam velocity is
absorbed. This process continues till steam reaches the condenser pressure. Due to pressure
compounding, smaller transformation of heat energy into kinetic energy takes place. Hence steam
velocities become much lower and rotor speed decrease considerably. The pressure compounded
impulse turbine is also called the Rateau turbine stage.
3.5.3 Pressure-Velocity Compounding:
Question No 3.5: Explain with a neat sketch pressure-velocity compounding. (Dec-03/Jan-07, Jun/Jul-
13)
Answer: If pressure and velocity are both compounded using two or more number of stages by having
a series arrangement of simple velocity compounded turbines on the same shaft, it is known as
pressure-velocity compounding. In this type of turbine both pressure compounding and velocity
compounding methods are used. The total pressure drop of the steam is dividing into two stages and
the velocity obtained in each stage is also compounded. Pressure drop occurs only in nozzles and
remains constant in moving and fixed blades. As pressure drop is large in each stage only a few stages
are necessary. This makes the turbine more compact than the other two types. Pressure-velocity
compounding is used in Curtis turbine.

Fig. 3.5 Pressure-velocity compounded impulse turbine.

3.3 Efficiencies of Steam Turbine:
Question No 3.3: Define and explain (i) blade coefficient (ii) nozzle efficiency (iii) diagram
efficiency (iv) stage efficiency. (VTU, Dec-11, Dec-12)

Page | 5
Steam and Gas Turbines

Answer: Some performance parameters of steam turbines are as follows:

(i) Blade coefficient: It is also known as nozzle velocity coefficient. The losses in the flow over blades
are due to friction, leakage and turbulence. Blade coefficient is the ratio of the velocity at the exit to
the velocity at the inlet of the blade. i.e.,
𝑉𝑟2 𝑉2
𝐶𝑏 = =
𝑉𝑟1 𝑉1
(ii) Nozzle efficiency: It is defined as the ratio of actual enthalpy change per kg of steam to the
isentropic enthalpy change per kg of steam. i.e.,
Δℎ
𝜂𝑛 =
Δℎ′
For impulse turbine,
1 2
𝑉1
𝜂𝑛 = 2
Δℎ′
For reaction turbine the stator efficiency is,
1 2 1 2 2
𝑉1 − 2 (𝑉𝑟1 − 𝑉𝑟2 )
𝜂𝑝 = 2
Δℎ′
(iii) Diagram efficiency: It is also known as blade efficiency or rotor efficiency. It is defined as the
ratio of work done per kg of steam by the rotor to the energy available at the inlet per kg of steam. i.e.,
𝑤 𝑈Δ𝑉𝑢
𝜂𝑏 = =
𝑒𝑎 𝑒𝑎
1
For impulse turbine, 𝑒𝑎 = 2 𝑉12
1 1
For reaction turbine, 𝑒𝑎 = 2 𝑉12 − 2 (𝑉𝑟1
2 2
− 𝑉𝑟2 )

(iv) Stage efficiency: It is defined as the ratio of work done per kg of steam by the rotor to the
isentropic enthalpy change per kg of steam in the nozzle. i.e.,
𝑤
𝜂𝑠 =
Δℎ′
For impulse turbine,
1 2
𝑈Δ𝑉𝑢 2 𝑉1
𝜂𝑠 = ×
1 2 Δℎ′
2 𝑉1
Or, 𝜂𝑠 = 𝜂𝑏 × 𝜂𝑛
For reaction turbine,
1 2 1 2 2
𝑈Δ𝑉𝑢 𝑉1 − 2 (𝑉𝑟1 − 𝑉𝑟2 )
𝜂𝑠 = × 2
1 2 1 2 2 Δℎ′
2 𝑉1 − 2 (𝑉𝑟1 − 𝑉𝑟2 )
Or, 𝜂𝑠 = 𝜂𝑏 × 𝜂𝑝
Page | 6
Steam and Gas Turbines

3.7 De’ Laval Turbine (Single Stage Axial Flow Impulse Turbine):
Question No 3.7: Show that for a single stage axial flow impulse turbine the rotor efficiency is given
𝒄𝒐𝒔𝜷 𝑽
by, 𝜼𝒃 = 𝟐(𝝋𝒄𝒐𝒔𝜶𝟏 − 𝝋𝟐 ) [𝟏 + 𝑪𝒃 𝒄𝒐𝒔𝜷𝟐 ], where 𝑪𝒃 = 𝑽𝒓𝟐 , φ is speed ratio, β1 and β2 are rotating
𝟏 𝒓𝟏

blade angles at inlet and exit, Vr1 and Vr2 are relative velocities at inlet and exit.
(VTU, Feb-03, Jun/Jul-14)
Answer: The combined velocity diagram for an axial flow impulse turbine is as shown in figure 3.3.

Fig. 3.3 Combined velocity diagram for an axial flow impulse turbine
Energy transfer for an axial flow turbine,
𝑒 = 𝑤 = 𝑈Δ𝑉𝑢 = 𝑈(𝑉𝑢1 + 𝑉𝑢2 )
From velocity diagram, 𝑉𝑢1 + 𝑉𝑢2 = 𝑥1 + 𝑈 + 𝑥2 − 𝑈 = 𝑥1 + 𝑥2
Or, 𝑉𝑢1 + 𝑉𝑢2 = 𝑉𝑟1 𝑐𝑜𝑠𝛽1 + 𝑉𝑟2 𝑐𝑜𝑠𝛽2
𝑉𝑟2𝑐𝑜𝑠𝛽2 𝑐𝑜𝑠𝛽2
𝑉𝑢1 + 𝑉𝑢2 = 𝑉𝑟1 𝑐𝑜𝑠𝛽1 [1 + ] = 𝑥1 [1 + 𝐶𝑏 ]
𝑉𝑟1 𝑐𝑜𝑠𝛽1 𝑐𝑜𝑠𝛽1
𝑉
Where 𝐶𝑏 = 𝑉𝑟2, blade velocity coefficient
𝑟1

𝑐𝑜𝑠𝛽2 𝑐𝑜𝑠𝛽2
𝑉𝑢1 + 𝑉𝑢2 = (𝑉𝑢1 − 𝑈) [1 + 𝐶𝑏 ] = (𝑉1 𝑐𝑜𝑠𝛼1 − 𝑈) [1 + 𝐶𝑏 ]
𝑐𝑜𝑠𝛽1 𝑐𝑜𝑠𝛽1
Then,
𝑐𝑜𝑠𝛽2
𝑤 = 𝑈(𝑉1 𝑐𝑜𝑠𝛼1 − 𝑈) [1 + 𝐶𝑏 ]
𝑐𝑜𝑠𝛽1
Blade or rotor efficiency is given by,
𝑤 𝑈(𝑉1 𝑐𝑜𝑠𝛼1 − 𝑈) 𝑐𝑜𝑠𝛽2
𝜂𝑏 = = [1 + 𝐶𝑏 ]
𝑒𝑎 1 2 𝑐𝑜𝑠𝛽1
2 𝑉1
𝑈 𝑈2 𝑐𝑜𝑠𝛽2
𝜂𝑏 = 2 ( 𝑐𝑜𝑠𝛼1 − 2 ) [1 + 𝐶𝑏 ]
𝑉1 𝑉1 𝑐𝑜𝑠𝛽1
Page | 7
Steam and Gas Turbines

𝒄𝒐𝒔𝜷𝟐
𝜼𝒃 = 𝟐(𝝋𝒄𝒐𝒔𝜶𝟏 − 𝝋𝟐 ) [𝟏 + 𝑪𝒃 ]
𝒄𝒐𝒔𝜷𝟏
𝑈
Where 𝜑 = 𝑉 , blade speed ratio
1

Question No 3.8: Find the condition of maximum blade efficiency in a single stage impulse turbine.
(VTU, Jan/Feb-03)
Answer: The blade efficiency for single stage impulse turbine is given by,
𝑐𝑜𝑠𝛽2
𝜂𝑏 = 2(𝜑𝑐𝑜𝑠𝛼1 − 𝜑 2 ) [1 + 𝐶𝑏 ]
𝑐𝑜𝑠𝛽1
The variation of blade efficiency vs. speed ratio is shown in figure 3.7.

Fig. 3.7 Variation of blade efficiency vs. speed ratio

The slope for maximum blade efficiency is,
𝑑𝜂𝑏
=0
𝑑𝜑
𝑑 𝑐𝑜𝑠𝛽2
{2(𝜑𝑐𝑜𝑠𝛼1 − 𝜑 2 ) [1 + 𝐶𝑏 ]} = 0
𝑑𝜑 𝑐𝑜𝑠𝛽1
𝑐𝑜𝑠𝛽2
2(𝑐𝑜𝑠𝛼1 − 2𝜑) [1 + 𝐶𝑏 ]=0
𝑐𝑜𝑠𝛽1
𝒄𝒐𝒔𝜶𝟏
𝝋𝒐𝒑𝒕 =
𝟐
The optimum speed ratio is the speed ratio at which the blade efficiency is the maximum.
Question No 3.9: For a single stage impulse turbine, prove that the maximum blade efficiency is
𝒄𝒐𝒔𝟐 𝜶𝟏 𝒄𝒐𝒔𝜷 𝑽
given by 𝜼𝒃,𝒎𝒂𝒙 = [𝟏 + 𝑪𝒃 𝒄𝒐𝒔𝜷𝟐 ], where 𝑪𝒃 = 𝑽𝒓𝟐 , α1 is speed ratio, β1 and β2 are rotating
𝟐 𝟏 𝒓𝟏

blade angles at inlet and exit, Vr1 and Vr2 are relative velocities at inlet and exit. (VTU, Dec-08/Jan-09)
Answer: The blade efficiency for single stage impulse turbine is given by,
𝑐𝑜𝑠𝛽2
𝜂𝑏 = 2(𝜑𝑐𝑜𝑠𝛼1 − 𝜑 2 ) [1 + 𝐶𝑏 ]
𝑐𝑜𝑠𝛽1
Page | 8
Steam and Gas Turbines

𝒄𝒐𝒔𝜶𝟏
When 𝜑 = , the blade efficiency is the maximum, therefore
𝟐

𝑐𝑜𝑠𝛼1 𝑐𝑜𝑠𝛼1 2 𝑐𝑜𝑠𝛽2

𝜂𝑏,𝑚𝑎𝑥 = 2 [( ) 𝑐𝑜𝑠𝛼1 − ( ) ] [1 + 𝐶𝑏 ]
2 2 𝑐𝑜𝑠𝛽1
𝒄𝒐𝒔𝟐 𝜶𝟏 𝒄𝒐𝒔𝜷𝟐
𝜼𝒃,𝒎𝒂𝒙 = [𝟏 + 𝑪𝒃 ]
𝟐 𝒄𝒐𝒔𝜷𝟏
Question No 3.10: Prove that the maximum blade efficiency for a single stage impulse turbine with
𝒄𝒐𝒔𝟐 𝜶𝟏
equiangular rotor blades is given by 𝜼𝒃,𝒎𝒂𝒙 = [𝟏 + 𝑪𝒃 ], where α1 is the nozzle angle and Cb is
𝟐

blade velocity coefficient. (VTU, Dec-10) Or,

Prove that the maximum blade efficiency for a single stage impulse turbine with equiangular rotor
blades is given by 𝜼𝒃,𝒎𝒂𝒙 = 𝒄𝒐𝒔𝟐 𝜶𝟏 , where α1 is the nozzle angle. (VTU, Jun/Jul-09, Jun/Jul-13)
Answer: The maximum blade efficiency for a single stage impulse turbine is,
𝑐𝑜𝑠 2 𝛼1 𝑐𝑜𝑠𝛽2
𝜂𝑏,𝑚𝑎𝑥 = [1 + 𝐶𝑏 ]
2 𝑐𝑜𝑠𝛽1
For equiangular rotor blades, β1=β2
𝒄𝒐𝒔𝟐 𝜶𝟏
𝜼𝒃,𝒎𝒂𝒙 = [𝟏 + 𝑪𝒃 ]
𝟐
If no losses due to friction, leakage and turbulence in the flow over blades, Vr1=Vr2 (i.e. Cb=1)
𝑐𝑜𝑠 2 𝛼1
𝜂𝑏,𝑚𝑎𝑥 = [1 + 1]
2
𝜼𝒃,𝒎𝒂𝒙 = 𝒄𝒐𝒔𝟐 𝜶𝟏
Above equation conclude that, if the flow over blades doesn’t have any losses due to friction, leakage
and turbulence then for a single stage impulse turbine with equiangular rotor blades maximum blade
efficiency is same as maximum utilization factor.
3.8 Curtis Turbine (Velocity Compounded Axial Flow Impulse Turbine):
The velocity diagrams for first and second stages of a Curtis turbine (velocity compounded
impulse turbine) are as shown in figure 3.8. The tangential speed of blade for both the rows is same
since all the moving blades are mounted on the same shaft. Assume equiangular stator and rotors
blades and blade velocity coefficients for stator and rotors are same.
The work done by first row of moving blades is,
𝑤1 = 𝑈Δ𝑉𝑢1 = 𝑈(𝑉𝑢1 + 𝑉𝑢2 )
From first stage velocity diagram,
𝑉𝑢1 = 𝑉1 𝑐𝑜𝑠𝛼1
And also,
𝑉𝑢2 = 𝑥2 − 𝑈 = 𝑉𝑟2 𝑐𝑜𝑠𝛽2 − 𝑈

Page | 9
Steam and Gas Turbines

𝑉𝑢2 = 𝐶𝑏 𝑉𝑟1 𝑐𝑜𝑠𝛽1 − 𝑈

(𝐵𝑒𝑐𝑎𝑢𝑠𝑒 𝛽1 = 𝛽2 𝑎𝑛𝑑 𝑉𝑟2 = 𝐶𝑏 𝑉𝑟1 )
𝑉𝑢2 = 𝐶𝑏 𝑥1 − 𝑈 = 𝐶𝑏 (𝑉𝑢1 − 𝑈) − 𝑈
(𝐵𝑒𝑐𝑎𝑢𝑠𝑒 𝑉𝑟1𝑐𝑜𝑠𝛽1 = 𝑥1 = 𝑉𝑢1 − 𝑈)
𝑽𝒖𝟐 = 𝑪𝒃 (𝑽𝟏 𝒄𝒐𝒔𝜶𝟏 − 𝑼) − 𝑼
(𝐵𝑒𝑐𝑎𝑢𝑠𝑒 𝑉𝑢1 = 𝑉1 𝑐𝑜𝑠𝛼1 )

Fig. 3.8 Velocity diagrams for first and second stages of a Curtis turbine.
Then,
𝑤1 = 𝑈(𝑉1 𝑐𝑜𝑠𝛼1 + 𝐶𝑏 (𝑉1 𝑐𝑜𝑠𝛼1 − 𝑈) − 𝑈)
𝑤1 = 𝑈𝑉1 𝑐𝑜𝑠𝛼1 + 𝐶𝑏 𝑈𝑉1 𝑐𝑜𝑠𝛼1 − 𝐶𝑏 𝑈 2 − 𝑈 2
𝑤1 = (1 + 𝐶𝑏 )𝑈𝑉1 𝑐𝑜𝑠𝛼1 − (1 + 𝐶𝑏 )𝑈 2
𝒘𝟏 = (𝟏 + 𝑪𝒃 )[𝑼𝑽𝟏 𝒄𝒐𝒔𝜶𝟏 − 𝑼𝟐 ]
Similarly work done by second stage is,
𝑤2 = (1 + 𝐶𝑏 )[𝑈𝑉3 𝑐𝑜𝑠𝛼3 − 𝑈 2 ]
𝑤2 = (1 + 𝐶𝑏 )[𝐶𝑏 𝑈𝑉2 𝑐𝑜𝑠𝛼2 − 𝑈 2 ]
(𝐵𝑒𝑐𝑎𝑢𝑠𝑒 𝛼3 = 𝛼2 𝑎𝑛𝑑 𝑉3 = 𝐶𝑏 𝑉2 )
Page | 10
Steam and Gas Turbines

𝑤2 = (1 + 𝐶𝑏 )[𝐶𝑏 𝑈𝑉𝑢2 − 𝑈 2 ]
(𝐵𝑒𝑐𝑎𝑢𝑠𝑒 𝑉2 𝑐𝑜𝑠𝛼2 = 𝑉𝑢2 )
𝑤2 = (1 + 𝐶𝑏 )[𝐶𝑏 𝑈{𝐶𝑏 (𝑉1 𝑐𝑜𝑠𝛼1 − 𝑈) − 𝑈} − 𝑈 2 ]
(𝐵𝑒𝑐𝑎𝑢𝑠𝑒 𝑉𝑢2 = 𝐶𝑏 (𝑉1 𝑐𝑜𝑠𝛼1 − 𝑈) − 𝑈)
𝑤2 = (1 + 𝐶𝑏 )[𝐶𝑏 2 𝑈𝑉1 𝑐𝑜𝑠𝛼1 − 𝐶𝑏 2 𝑈 2 − 𝐶𝑏 𝑈 2 − 𝑈 2 ]
𝒘𝟐 = (𝟏 + 𝑪𝒃 )[𝑪𝒃 𝟐 𝑼𝑽𝟏 𝒄𝒐𝒔𝜶𝟏 − 𝑼𝟐 (𝟏 + 𝑪𝒃 + 𝑪𝒃 𝟐 )]
The total work done by the Curtis turbine is, 𝑤𝑇 = 𝑤1 + 𝑤2
2 2
𝑤𝑇 = (1 + 𝐶𝑏 )[𝑈𝑉1 𝑐𝑜𝑠𝛼1 − 𝑈2 ] + (1 + 𝐶𝑏 ) [𝐶𝑏 𝑈𝑉1 𝑐𝑜𝑠𝛼1 − 𝑈2 (1 + 𝐶𝑏 + 𝐶𝑏 )]
2 2 2
𝑤𝑇 = (1 + 𝐶𝑏 ) [(1 + 𝐶𝑏 ) 𝑈𝑉1 𝑐𝑜𝑠𝛼1 − 𝑈 (2 + 𝐶𝑏 + 𝐶𝑏 )]

𝐿𝑒𝑡, 𝐶𝑏′ = (1 + 𝐶𝑏 )(1 + 𝐶𝑏 2 ) 𝑎𝑛𝑑 𝐶𝑏" = (1 + 𝐶𝑏 )(2 + 𝐶𝑏 + 𝐶𝑏 2 )

Then,
′ "
𝒘𝑻 = [𝑪𝒃 𝑼𝑽𝟏 𝒄𝒐𝒔𝜶𝟏 − 𝑪𝒃 𝑼𝟐 ]

Blade or rotor efficiency is given by,

𝑤𝑇 (𝐶𝑏′ 𝑈𝑉1 𝑐𝑜𝑠𝛼1 − 𝐶𝑏" 𝑈 2 )
𝜂𝑏 = =
𝑒𝑎 1 2
2 𝑉1
𝑈 𝑈2
𝜂𝑏 = 2 (𝐶𝑏′ ( ) 𝑐𝑜𝑠𝛼1 − 𝐶𝑏" ( 2 ))
𝑉1 𝑉1

𝜼𝒃 = 𝟐(𝑪′𝒃 𝝋𝒄𝒐𝒔𝜶𝟏 − 𝑪"𝒃 𝝋𝟐 )

The slope for maximum blade efficiency is,
𝑑𝜂𝑏
=0
𝑑𝜑
𝑑
{2(𝐶𝑏′ 𝜑𝑐𝑜𝑠𝛼1 − 𝐶𝑏" 𝜑 2 )} = 0
𝑑𝜑
2(𝐶𝑏′ 𝑐𝑜𝑠𝛼1 − 2𝐶𝑏" 𝜑) = 0
𝑪′𝒃 𝒄𝒐𝒔𝜶𝟏
𝝋𝒐𝒑𝒕 = ( " )
𝑪𝒃 𝟐
The maximum blade efficiency is,
2
𝐶𝑏′ 𝑐𝑜𝑠𝛼1 𝐶𝑏′ 𝑐𝑜𝑠𝛼1
𝜂𝑏,𝑚𝑎𝑥 = 2 (𝐶𝑏′ (( " ) ) 𝑐𝑜𝑠𝛼1 − 𝐶𝑏" (( " ) ) )
𝐶𝑏 2 𝐶𝑏 2

(𝐶𝑏′ )2 𝑐𝑜𝑠 2 𝛼1 (𝐶𝑏′ )2 𝑐𝑜𝑠 2 𝛼1

𝜂𝑏,𝑚𝑎𝑥 = 2 ( ( ) − ( ))
𝐶𝑏" 2 𝐶𝑏" 4

Page | 11
Steam and Gas Turbines

(𝑪′𝒃 )𝟐 𝒄𝒐𝒔𝟐 𝜶𝟏
𝜼𝒃,𝒎𝒂𝒙 = ( )
𝑪"𝒃 𝟐
Note: If blade velocity coefficient, 𝑪𝒃 = 𝟏
Then, 𝐶𝑏′ = 4 and 𝐶𝑏" = 8
For single stage impulse turbine,
𝑤 = 2[𝑈𝑉1 𝑐𝑜𝑠𝛼1 − 𝑈 2 ]
𝑐𝑜𝑠𝛼1
𝜑𝑜𝑝𝑡 =
2
𝜂𝑏,𝑚𝑎𝑥 = 𝑐𝑜𝑠 2 𝛼1
For Curtis (two stage velocity compounded) turbine,
2
𝑤𝑇 = 4[𝑈𝑉1 𝑐𝑜𝑠𝛼1 − 2𝑈 ]
𝑐𝑜𝑠𝛼1
𝜑𝑜𝑝𝑡 =
4
𝜂𝑏,𝑚𝑎𝑥 = 𝑐𝑜𝑠 2 𝛼1
Similarly for ‘n’ stage Curtis (velocity compounded) turbine,
𝑤 = 2𝑛[𝑈𝑉1 𝑐𝑜𝑠𝛼1 − 𝑈 2 ]
𝑐𝑜𝑠𝛼1
𝜑𝑜𝑝𝑡 =
2𝑛
𝜂𝑏,𝑚𝑎𝑥 = 𝑐𝑜𝑠 2 𝛼1
For all Curtis turbines the maximum blade efficiency remains same irrespective of their number of
stages.
3.9 Parson’s Turbine (50% Axial Flow Reaction Turbine):
Question No 3.12: Show that for an axial flow reaction turbine, the degree of reaction is given by
𝑽
𝑹 = (𝟐𝑼𝒂 ) [𝒄𝒐𝒕𝜷𝟐 − 𝒄𝒐𝒕𝜷𝟏 ] and also show that for axial flow 50% reaction turbine the blade speed

is given by 𝑼 = 𝑽𝒂 [𝒄𝒐𝒕𝜷𝟐 − 𝒄𝒐𝒕𝜷𝟏 ], where β1 and β2 are inlet and outlet rotor blade angles.
Assume velocity of flow or axial velocity to be constant. (VTU, Jun-12)
Answer: The combined velocity diagram for an axial flow reaction turbine is as shown in figure 3.9.
From data given in the problem, Va1=Va2=Va.
Degree of reaction for axial flow turbine,
1 2 2)
(𝑉𝑟2 − 𝑉𝑟1 2
(𝑉𝑟2 2)
− 𝑉𝑟1
𝑅= 2 =
𝑒 2𝑒
From velocity diagram, (𝑉𝑢1 + 𝑉𝑢2 ) = (𝑥1 + 𝑈 + 𝑥2 − 𝑈)
= (𝑥1 + 𝑥2 ) = (𝑉𝑎1 𝑐𝑜𝑡𝛽1 + 𝑉𝑎2 𝑐𝑜𝑡𝛽2 )
Or, (𝑉𝑢1 + 𝑉𝑢2 ) = 𝑉𝑎 (𝑐𝑜𝑡𝛽1 + 𝑐𝑜𝑡𝛽2 )

Page | 12
Steam and Gas Turbines

𝑉𝑎2 𝑎2 𝑉
From velocity diagram, 𝑠𝑖𝑛𝛽2 = ⟹ 𝑉𝑟2 = 𝑠𝑖𝑛𝛽
𝑉𝑟2 2

𝑉𝑟2 = 𝑉𝑎 𝑐𝑜𝑠𝑒𝑐𝛽2
𝑉𝑎1 𝑉
𝑎1
Similarly, 𝑠𝑖𝑛𝛽1 = ⟹ 𝑉𝑟1 = 𝑠𝑖𝑛𝛽
𝑉𝑟1 1

𝑉𝑟1 = 𝑉𝑎 𝑐𝑜𝑠𝑒𝑐𝛽1

Fig. 3.9 Combined velocity diagram for an axial flow reaction turbine
Then, 𝑒 = 𝑈(𝑉𝑢1 + 𝑉𝑢2 ) ⟹ 𝒆 = 𝑼𝑽𝒂 (𝒄𝒐𝒕𝜷𝟏 + 𝒄𝒐𝒕𝜷𝟐 )
2
And, (𝑉𝑟2 2)
− 𝑉𝑟1 = (𝑉𝑎2 𝑐𝑜𝑠𝑒𝑐 2 𝛽2 − 𝑉𝑎2 𝑐𝑜𝑠𝑒𝑐 2 𝛽1 ) ⟹ (𝑽𝟐𝒓𝟐 − 𝑽𝟐𝒓𝟏 ) = 𝑽𝟐𝒂 (𝒄𝒐𝒔𝒆𝒄𝟐 𝜷𝟐 − 𝒄𝒐𝒔𝒆𝒄𝟐 𝜷𝟏 )
Therefore,
𝑉𝑎2 (𝑐𝑜𝑠𝑒𝑐 2 𝛽2 − 𝑐𝑜𝑠𝑒𝑐 2 𝛽1 )
𝑅=
2𝑈𝑉𝑎 (𝑐𝑜𝑡𝛽1 + 𝑐𝑜𝑡𝛽2 )
𝑉𝑎 [(1 + 𝑐𝑜𝑡 2 𝛽2 ) − (1 + 𝑐𝑜𝑡 2 𝛽1 )]
𝑅=
2𝑈(𝑐𝑜𝑡𝛽1 + 𝑐𝑜𝑡𝛽2 )
𝑉𝑎 [(𝑐𝑜𝑡 2 𝛽2 ) − (𝑐𝑜𝑡 2 𝛽1 )]
𝑅=
2𝑈(𝑐𝑜𝑡𝛽1 + 𝑐𝑜𝑡𝛽2 )
𝑉𝑎 [(𝑐𝑜𝑡𝛽2 − 𝑐𝑜𝑡𝛽1 )(𝑐𝑜𝑡𝛽2 + 𝑐𝑜𝑡𝛽1 )]
𝑅=
2𝑈(𝑐𝑜𝑡𝛽1 + 𝑐𝑜𝑡𝛽2 )
𝑽𝒂
𝑹 = ( ) [𝒄𝒐𝒕𝜷𝟐 − 𝒄𝒐𝒕𝜷𝟏 ]
𝟐𝑼
For an axial flow 50% reaction turbine, R=0.5
1 𝑉𝑎
0.5 = = ( ) [𝑐𝑜𝑡𝛽2 − 𝑐𝑜𝑡𝛽1 ]
2 2𝑈
𝑼 = 𝑽𝒂 [𝒄𝒐𝒕𝜷𝟐 − 𝒄𝒐𝒕𝜷𝟏 ]
Alternate method:
From velocity diagram, 𝑈 = 𝑉𝑢1 − 𝑥1 = 𝑉𝑎1 𝑐𝑜𝑡𝛼1 − 𝑉𝑎1 𝑐𝑜𝑡𝛽1
For an axial flow 50% reaction turbine, α1=β2 and α2=β1 and also V1=Vr2 and V2=Vr1

Page | 13
Steam and Gas Turbines

𝑼 = 𝑽𝒂 [𝒄𝒐𝒕𝜷𝟐 − 𝒄𝒐𝒕𝜷𝟏 ]
Question No 3.13: For a 50% reaction steam turbine, show that α1=β2 and α2=β1, where α1 and β1
are the inlet angles of fixed and moving blades, α2 and β2 are the outlet angles of fixed and moving
blades. (VTU, Dec-12)
Answer: The general equation of degree of reaction for axial flow reaction steam turbine is,
𝑉𝑎
𝑅=( ) [𝑐𝑜𝑡𝛽2 − 𝑐𝑜𝑡𝛽1 ]
2𝑈
𝑉𝑎
𝑅=( ) [(𝑐𝑜𝑡𝛽2 − 𝑐𝑜𝑡𝛼1 ) + (𝑐𝑜𝑡𝛼1 − 𝑐𝑜𝑡𝛽1 )]
2𝑈
From velocity diagram (fig.3.9), 𝑈 = 𝑉𝑢1 − 𝑥1 = 𝑉𝑎1 𝑐𝑜𝑡𝛼1 − 𝑉𝑎1 𝑐𝑜𝑡𝛽1
Assume velocity of flow or axial velocity to be constant, Va1=Va2=Va
𝑈 = 𝑉𝑎 (𝑐𝑜𝑡𝛼1 − 𝑐𝑜𝑡𝛽1 )
Or,
𝑈
= (𝑐𝑜𝑡𝛼1 − 𝑐𝑜𝑡𝛽1 )
𝑉𝑎
Then,
𝑉𝑎 𝑈
𝑅 = ( ) [(𝑐𝑜𝑡𝛽2 − 𝑐𝑜𝑡𝛼1 ) + ]
2𝑈 𝑉𝑎
𝟏 𝑽𝒂 𝟏
𝑹= ( ) (𝒄𝒐𝒕𝜷𝟐 − 𝒄𝒐𝒕𝜶𝟏 ) +
𝟐 𝑼 𝟐
For a 50% reaction steam turbine, 𝑅 = 1⁄2
Therefore, 0 = 𝑐𝑜𝑡𝛽2 − 𝑐𝑜𝑡𝛼1 ⇒ 𝑐𝑜𝑡𝛼1 = 𝑐𝑜𝑡𝛽2
Or, 𝜶𝟏 = 𝜷𝟐
From velocity diagram (fig.3.9), 𝑈 = 𝑥2 − 𝑉𝑢2 = 𝑉𝑎2 𝑐𝑜𝑡𝛽2 − 𝑉𝑎2 𝑐𝑜𝑡𝛼2
Assume velocity of flow or axial velocity to be constant, Va1=Va2=Va
𝑈 = 𝑉𝑎 (𝑐𝑜𝑡𝛽2 − 𝑐𝑜𝑡𝛼2 )
Then, 𝑈 = 𝑉𝑎 (𝑐𝑜𝑡𝛼1 − 𝑐𝑜𝑡𝛽1 ) = 𝑉𝑎 (𝑐𝑜𝑡𝛽2 − 𝑐𝑜𝑡𝛼2 )
But, 𝛼1 = 𝛽2
𝑉𝑎 (𝑐𝑜𝑡𝛽2 − 𝑐𝑜𝑡𝛽1 ) = 𝑉𝑎 (𝑐𝑜𝑡𝛽2 − 𝑐𝑜𝑡𝛼2 )
𝑐𝑜𝑡𝛽1 = 𝑐𝑜𝑡𝛼2
Or, 𝜶𝟐 = 𝜷𝟏
From velocity diagram (fig.3.9), 𝑉𝑎 = 𝑉1 𝑐𝑜𝑠𝛼1 = 𝑉𝑟2 𝑐𝑜𝑠𝛽2
But, 𝛼1 = 𝛽2
𝑽𝟏 = 𝑽𝒓𝟐
𝑉𝑎 = 𝑉2 𝑐𝑜𝑠𝛼2 = 𝑉𝑟1 𝑐𝑜𝑠𝛽1

Page | 14
Steam and Gas Turbines

But, 𝛼2 = 𝛽1
𝑽𝟐 = 𝑽𝒓𝟏
These relations show that the velocity triangles at the inlet and outlet of the rotor of a 50% reaction
stage are symmetrical.
Question No 3.14: What is meant by reaction staging? Prove that the maximum blade efficiency of
𝟐𝒄𝒐𝒔𝟐 𝜶
Parson’s (axial flow 50% reaction) turbine is given by 𝜼𝒃,𝒎𝒂𝒙 = 𝟏+𝒄𝒐𝒔𝟐 𝜶𝟏 .
𝟏

(VTU, Jan/Feb-04, Jun/Jul-08, May/Jun-10, Dec-14/Jan-15)

Answer: In reaction staging the expansion of steam and enthalpy drop occurs both in fixed and
moving blades. Due to the effect of continuous expansion during flow over the moving blades, the
relative velocity of steam increases i.e., Vr2>Vr1.
For Parson’s (axial flow 50% reaction) turbine, α1=β2 and α2=β1 and also V1=Vr2 and V2=Vr1, then the
velocity triangles are symmetric (refer figure 3.9).
Work done by Parson’s turbine,
𝑤 = 𝑈∆𝑉𝑢 = 𝑈(𝑉𝑢1 + 𝑉𝑢2 )
From velocity diagram,
𝑤 = 𝑈(𝑉𝑢1 + 𝑥2 − 𝑈) = 𝑈(𝑉1 𝑐𝑜𝑠𝛼1 + 𝑉𝑟2 𝑐𝑜𝑠𝛽2 − 𝑈)
But, α1=β2 and V1=Vr2
Then, 𝑤 = 𝑈(𝑉1 𝑐𝑜𝑠𝛼1 + 𝑉1 𝑐𝑜𝑠𝛼1 − 𝑈) = 2𝑈𝑉1 𝑐𝑜𝑠𝛼1 − 𝑈 2
Or,
2𝑈𝑉1 𝑐𝑜𝑠𝛼1 𝑈 2
𝑤 = 𝑉12 [ − 2]
𝑉12 𝑉1
𝑈
But, blade speed ratio 𝜑 = 𝑉
1

𝒘 = 𝑽𝟐𝟏 [𝟐𝝋𝒄𝒐𝒔𝜶𝟏 − 𝝋𝟐 ]
For reaction turbine energy available at rotor inlet,
1 1 2
𝑒𝑎 = 𝑉12 − (𝑉𝑟1 2
− 𝑉𝑟2 )
2 2

But V1=Vr2,
2
1 2 1 2 2) 2
𝑉𝑟1
𝑒𝑎 = 𝑉1 − (𝑉 − 𝑉1 = 𝑉1 −
2 2 𝑟1 2
From velocity diagram,
2
𝑉𝑟1 = 𝑉12 + 𝑈 2 − 2𝑈𝑉1 𝑐𝑜𝑠𝛼1 (By cosine rule)
Then,
1
𝑒𝑎 = 𝑉12 − [𝑉12 + 𝑈 2 − 2𝑈𝑉1 𝑐𝑜𝑠𝛼1 ]
2
Page | 15
Steam and Gas Turbines

1 𝑉12 2𝑈𝑉1 𝑐𝑜𝑠𝛼1 𝑈 2

𝑒𝑎 = [𝑉12 + 2𝑈𝑉1 𝑐𝑜𝑠𝛼1 −𝑈 2 ] = [1 + − 2]
2 2 𝑉12 𝑉1
𝑈
But, blade speed ratio 𝜑 = 𝑉
1

𝑽𝟐𝟏
𝒆𝒂 = [𝟏 + 𝟐𝝋𝒄𝒐𝒔𝜶𝟏 − 𝝋𝟐 ]
𝟐
Blade efficiency of reaction turbine,
𝑤 𝑉12 [2𝜑𝑐𝑜𝑠𝛼1 − 𝜑 2 ]
𝜂𝑏 = =
𝑒𝑎 𝑉12
[1 + 2𝜑𝑐𝑜𝑠𝛼1 − 𝜑 2 ]
2
𝟐[𝟐𝝋𝒄𝒐𝒔𝜶𝟏 − 𝝋𝟐 ]
𝜼𝒃 =
[𝟏 + 𝟐𝝋𝒄𝒐𝒔𝜶𝟏 − 𝝋𝟐 ]
Or,
2[1 + 2𝜑𝑐𝑜𝑠𝛼1 − 𝜑 2 ] − 2
𝜂𝑏 =
[1 + 2𝜑𝑐𝑜𝑠𝛼1 − 𝜑 2 ]
2
𝜂𝑏 = 2 − = 2 − 2[1 + 2𝜑𝑐𝑜𝑠𝛼1 − 𝜑 2 ]−1
[1 + 2𝜑𝑐𝑜𝑠𝛼1 − 𝜑 2 ]
The slope for maximum blade efficiency is (refer figure 3.7),
𝑑𝜂𝑏
=0
𝑑𝜑
𝑑
{2 − 2[1 + 2𝜑𝑐𝑜𝑠𝛼1 − 𝜑 2 ]−1 } = 0
𝑑𝜑
2[1 + 2𝜑𝑐𝑜𝑠𝛼1 − 𝜑 2 ]−2 [2𝑐𝑜𝑠𝛼1 − 2𝜑] = 0
[2𝑐𝑜𝑠𝛼1 − 2𝜑] = 0
𝝋𝒐𝒑𝒕 = 𝒄𝒐𝒔𝜶𝟏
When 𝜑 = 𝑐𝑜𝑠𝛼1 , the blade efficiency is the maximum, therefore
2[2𝑐𝑜𝑠 2 𝛼1 − 𝑐𝑜𝑠 2 𝛼1 ]
𝜂𝑏,𝑚𝑎𝑥 =
[1 + 2𝑐𝑜𝑠 2 𝛼1 − 𝑐𝑜𝑠 2 𝛼1 ]
𝟐𝒄𝒐𝒔𝟐 𝜶𝟏
𝜼𝒃,𝒎𝒂𝒙 =
𝟏 + 𝒄𝒐𝒔𝟐 𝜶𝟏

Page | 16