Geiger Muller Counter

Geiger Muller Counter: Construction, Principle, Working,
Plateau graph and Applications

Introduction
When radioactive isotopes are used in medical research work particularly in human
subjects it is very important that the amount of radioactive material given is as small
as possible, in order that there should be minimum harmful radiations. Hence a very
sensitive instrument is necessary to measure the radioactivity of materials.
Geiger and Muller developed a ‘Particle detector’ for measuring ‘ionizing rad iation’ in
1928. They named it as ‘Geiger Muller Counter’. Ever since then it has been one of the
most widely used nuclear detectors in the developmental days of Nuclear physics. The
particle detector developed by Geiger and Muller is a gas filled counter. The main
difference between ‘proportional counter’ and ‘Geiger -Muller Counter’ is in the
formation of the avalanche. In the proportional counter, the avalanche is formed only
at a point whereas in Geiger -Muller Counter it is formed in the central wire. Th erefore,
in GM Counter amplification is independent of initial ionization produced by the
ionizing particle.
Geiger counter is also called as Geiger tube. This instrument is actually used for
detecting and measuring ionizing radiation like alpha particles, beta particles, and
gamma rays. A Geiger-Müller counter can count individual particles at rates up to about
10,000 per second and is used widely in medicine and in prospecting for radioactive
ores.
Construction of Geiger-Muller counter
 It consists of a hollow metal case enclosed in a thin glass tube. This hollow metal case
acts as a cathode.
 A fine tungsten wire is stretched along the axis of the tube and is insulated by ebonite
plugs. This fine tungsten wire acts as anode.
 The tube is evacuated and th en partially filled with a mixture of 90% argon at 10 cm
pressure and 10% ethyl alcohol vapours at 1cm pressure. sten
 The fine tungsten wire is connected to positive terminal of a high tension battery
through a resistance R and the negative terminal is con nected to the metal tube.
 The direct current voltage is kept slightly less than that which will cause a discharge
between the electrodes.
 At one end of the tube a thin window of mica is arranged to allow the entry of radiation
into the tube.
Principle of Geiger-Muller counter
The basic principle of the Geiger Muller counter can be understood as follows. When an
ionizing particle passes through the gas in an ionizing chamber, it produces a few ions.
If the applied potential difference is strong enough, th ese ions will produce a secondary
ion avalanche whose total effect will be proportional to the energy associated with the
primary ionizing event.
If the applied potential difference is very high, the secondary ionization phenomenon
becomes so dominant that the primary ionizing event loses its importance. In other
words, the size of the final pulse produced depends only on the triggering off of
ionization by an ionizing particle but independent of the energy of this particle.
A high energy particle entering through the mica window will cause one or more of the
argon atoms to ionize. The electrons and ions of argon thus produced cause other argon
atoms to ionize in a cascade effect. The result of this one event is sudden, massive
electrical discharge that caus es a current pulse. The current through R produces a
voltage pulse of the order of 10μV. An electron pulse amplifier accepts the small pulse
voltage and amplifies them to about 5 to 50 V. The amplified output is then applied to
a counter. As each incoming particle produces a pulse, the number of incoming particles
can be counted.
Working of Geiger-Muller counter
The tube is filled with Argon gas, and around voltage of +400 Volts is applied to the thin
wire in the middle. When a particle arrives into th e tube, it takes an electron from Argon
atom. The electron is attracted to the central wire and as it rushes towards the wire,
the electron will knock other electrons from Argon atoms, causing an "avalanche". Thus
one single incoming particle will cause ma ny electrons to arrive at the wire, creating a
pulse which can be amplified and counted. This gives us a very sensitive detector.
Plateau graph of Geiger Muller counter

There is a threshold below which the tube doesn’t work. This can be several hundred
volts. After this, the number of pulses is proportional to the voltage. This region is
known as proportional region.
If the applied voltage is increased further, then a point will be reached after which the
count rate remains constant over a certain region . This region is known as plateau
region or Geiger region. This region is used for Geiger Muller operation.
Beyond the plateau region the applied electric field is so high that a continuous
discharge takes place in the tube and the count rate increases ver y rapidly. It does not
require any ionization event to happen so that the tube must not be used in this region.
The Geiger Muller counter can account for about 500 particles per second. The GM
counter will not register those particles that pass through i t in the dead time. Dead time
refers to the time taken by the tube to recover between counts. It requires about 200
μs for the tube to recover. If lot of particles enter the GM tube at a rapid rate, the tube
will not have time to recover and some particles may not be counted.
The efficiency of the counter is defined as the ration of the observed counts per second
to the number of ionizing particles entering the counter per second. Counting efficiency
is defined as the ability of counting of the GM counter.
Counting efficiency, η = 1- exp (spl)

Where,
s = specific ionization at one atmosphere
p= pressure in atmosphere
l = path length of the ionization particle in the counter
Precautionary measures while operating

 The operating voltage must correspond to the midpoint of flat plateau region of plateau
graph.
 If the continuous discharge is produced, the voltage should be lowered.
 The applied voltage must be relatively stabilized.
 Introduction of light should be prevented to avoid photo electric effect.
Applications of Geiger Muller counter

Geiger counters have many applications in radioactivity detection. Here are few of the
examples:
1. To detect radioactive rocks and minerals in the course of mineral prospecting.
2. For Fire responders for making an initial determination of radiation risk.
3. For Hazard Management personnel in checking for radiation danger in an emergency
situation.
4. To check for environmental levels of radioactivity near a nuclear power facility.
5. To test for danger amidst a nuclear accident or leakage of radioactive coolant.
6. To check for radioactive contamination of clothing and shoes in your workplace.
7. Radiation detection in the scrap metal processing business.
8. To check possible leakage or exposure to X -rays in a medical facility
9. To check for radiation in areas where depleted uranium ammunition shells have been
used.
10. To check for irradiated gemstones in the jewellery trade.
11. To check the levels of iodine 131 in cancer patients undergoing radiation therapy.
12. You are in close proximity to a uranium mine and want to test the soil and environment
for dangerous levels of radioactivity.
13. To test for radioactive contamination of food.
14. To check materials in your anthropology or archaeology field.
15. To check for radioactivity in metal objects in your h ome or office that could be made of
recycled radioactive materials.
It is important to note that Geiger-Muller counter does not detect the following,
 Neutron radiation
 Microwave radiation
 Radon gas
 Laser energy

Geiger Muller Counter

Uploaded by

Copyright:

Available Formats

Geiger Muller Counter

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Geiger Muller Counter

Uploaded by

Copyright:

Available Formats

Geiger Muller Counter: Construction, Principle, Working,

Plateau graph and Applications

Construction of Geiger-Muller counter

plugs. This fine tungsten wire acts as anode.

pressure and 10% ethyl alcohol vapours at 1cm pressure. sten

between the electrodes.

into the tube.

Principle of Geiger-Muller counter

Plateau graph of Geiger Muller counter

Counting efficiency, η = 1- exp (spl)

Precautionary measures while operating

 If the continuous discharge is produced, the voltage should be lowered.

 The applied voltage must be relatively stabilized.

 Introduction of light should be prevented to avoid photo electric effect.

Applications of Geiger Muller counter

1. To detect radioactive rocks and minerals in the course of mineral prospecting.

2. For Fire responders for making an initial determination of radiation risk.

3. For Hazard Management personnel in checking for radiation danger in an emergency

4. To check for environmental levels of radioactivity near a nuclear power facility.

5. To test for danger amidst a nuclear accident or leakage of radioactive coolant.

6. To check for radioactive contamination of clothing and shoes in your workplace.

7. Radiation detection in the scrap metal processing business.

8. To check possible leakage or exposure to X -rays in a medical facility

10. To check for irradiated gemstones in the jewellery trade.

for dangerous levels of radioactivity.

13. To test for radioactive contamination of food.

14. To check materials in your anthropology or archaeology field.

recycled radioactive materials.

You might also like