T205 - Uncertainty Analysis For Hydrometer Calibration at NMISA

Presenter: Bongani Ndlovu
The uncertainty evaluation for the Date: 09/10/2018

hydrometer calibration at NMISA
A HYDROMETER
• Thin graduated hollow tube

• Weighted at bottom end to
make it float upright
• USED
• To measure specific gravity,
concentration, density of liquids
500 – 2000 kg/m^3
HOW IT IS USED
• Floats in a liquid
• Liquid density is
where
• Liquid level aligns with
the scale
• e.g., Beer
concentration
• http://www.schoolphysics.co.uk/age11-14/Matter/text/Hydrometers_/index.html
• https://static.wixstatic.com/media/b0d342_7e2a75815d5b4b1a809e99475a547ae1~mv2.jpg_256
NEED FOR HYDROMETER CALIBRATION
• Over time, small drifts in scale occur due to

• Mechanical stress
• Abrasion
• Ageing process of glass
• Calibrate the hydrometer to quantify these small drifts
• Calibration gives the corrections of the drifts in the scale
• At NMISA, hydrometers are calibrated on the hydrometer
system using Cuckow’s method
HYDROMETER SYSTEM AT NMISA
• Consists of 200 g balance with 0,01 mg readability,

• Tamson TV7000 thermostat, CCD camera,
• Computer with software, visualization screen
SCHEMATIC DIAGRAM
• Thermostatic bath
• Inner vessel: Distilled water (reference liquid)…. 3 T sensors
• Liquid temperature maintained at ≈20 °C
CUCKOW’S METHOD
• Based on hydrostatic
weighing
• Hydrometer is weighed
in air and then in a
reference liquid
• Scale to be calibrated is
aligned to the liquid
level and the reference
liquid density is
determined at that point
• Wright JD, Bean VE and Aguilera J, 2010. NIST calibration services

for hydrometers. NIST Special Publication, 250, 78.
MEASUREMENTS
• Measure:
• Stem diameter of hydrometer using
a Vernier calliper
• Surface tension of the ref liquid
using tensiometer
• Hydrometer weighed in air:

• Measure m, air T, RH, P
• In the reference liquid:
Alignment: CCD camera magnified
image
• Measure m, air T, RH, P
• Liquid T
CUCKOW’S MODEL
CORRECTION:
• 𝑐 = 𝜌𝑥 − 𝜌𝑠𝑐𝑎𝑙𝑒
• where 𝜌𝑠𝑐𝑎𝑙𝑒 is the scale mark to be calibrated
S Lorefice et al. Measurement Sc. & tech., 17(10), 2006, 2560
UNCERTAINTY BUDGET
• Depends on several factors including
• Equipment used
• Reference liquid
• Mathematical model (Cuckow’s equation)
• Uncertainty calculations are based on the GUM,
2008
HYDROMETER MASS
• Mass in air
• Mass in liquid
• Depend on the reference mass uncertainty and
balance properties
Uncertainty
Ref. mass std. Repeatability Resolution Linearity
contribution
uncertainty (g) (g) (g) (g)
(g)
M_a 0,000017 0,0002 0,0001 -8E-06 2,24E-04
M_L 0,000020 0,00002 0,00001 -3E-05 4,24E-05
ADDITIONAL RING WEIGHTS
• In case of distilled water (ρ ≈ 1 g/ml)
• Hydrometer floats when its density range < 1 g/ml
• Requires additional ring weight
• Inner diameter almost equal to the stem diameter
• Weigh the ring weight in the reference liquid
AIR DENSITY
• Use the CIPM2007 equation
• Uncertainty depends on the measuring equipment
and the equation
• 𝑢 𝑇 , 𝑢𝑅𝐻 , 𝑢𝑃 and 𝑢𝑒𝑞𝑛
Standard Uncertainty
Variable Symbol Unit Value
Uncertainty contribution
Air temperature T_a °C 20,70 0,02 -1,13E-03
Air pressure p hPa 875,82 0,06 6,21E-10
Relative humidity rh %rh 38,5 1,3 -1,21E-05
Equation 2,28E-08
Air density unc. (g/ml) 1,13E-06
• A Picard et al., Metrologia 45 (2008) 149–155

WATER DENSITY
• Use the Tanaka formula
• Density based on SMOW at 1 atm (see level)
• 𝑎5 = 999,972 kg/m^3 assumed for tap water

• Apply compressibility correction factor
Uncert.
Variable Symbol Units Value Uncert. S_i Contribution
Water temp T_L °C 19,9815 0,06 -0,000206 -1,238E-05
Air pressure p hPa 875,822 0,06 4,58E-10 2,748E-11
Equation g/ml 4,5E-07 1 4,5E-07
Water density unc (g/ml) 1,238E-05
• M Tanaka et al. Metrologia, 2001, 38, 301-309

LOCAL GRAVITATIONAL ACCELERATION
• Gravitational acceleration
• 𝑢𝑔 = 𝑢 of g in the lab
• Gravitational acceleration gradient (Δg) due to height (ℎ)
difference
• hydrometer in liquid and balance on top
• 𝑢Δ𝑔 = Δg ∗ ℎ
OTHER CONTRIBUTORS:
IN CUCKOW’S MODEL
• Density of reference mass standard
• 𝑢ρ 𝑠𝑡𝑑 = 𝑢 from density certificate
• Hydrometer stem diameter
• 𝑢𝐷 = 𝑢 of Vernier calliper
• Surface tension of the reference liquid
• 𝑢γ = 𝑢 of the tensiometer
• Liquid temperature during measurement
• 𝑢 𝑇 = 𝑢 of the thermometer
• Thermal expansion coefficient β (glass) of the hydrometer
• 𝑢β = 10% β
ADDITIONAL CONTRIBUTIONS
• Scale alignment to the liquid level
• The scale alignment is magnified by CCD camera
1
• 𝑢𝑎𝑙𝑖𝑔𝑛 = (ℎ𝑦𝑑𝑟𝑜𝑚𝑒𝑡𝑒𝑟 𝑟𝑒𝑠𝑜𝑙𝑢𝑡𝑖𝑜𝑛)
10
• Repeatability of the measurement

• 𝑢𝑟𝑒𝑝𝑒𝑎𝑡 = 𝐸𝑆𝐷𝑀
THE UNCERTAINTY BUDGET
GRAPHICAL REPRESENTATION
1,20E-04
1,00E-04
8,00E-05
ρ_x (g/ml)
6,00E-05
4,00E-05
2,00E-05
0,00E+00
M_a M_L m_r ρ_s γ_x γ_L D g ρ_L ρ_a T_L β S R
CONCLUSIONS
• The uncertainty evaluation for hydrometer calibration
at NMISA has been presented
• The biggest uncertainty contribution came from the
surface tension of the reference liquid
• The uncertainty for the hydrometer calibration can be
reduced drastically by using a more suitable (low
density, low surface tension) reference liquid
(hydrocarbons e.g., tridecane, nonane) than distilled
water
I THANK YOU

T205 - Uncertainty Analysis For Hydrometer Calibration at NMISA

Uploaded by

Copyright:

Available Formats

T205 - Uncertainty Analysis For Hydrometer Calibration at NMISA

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

T205 - Uncertainty Analysis For Hydrometer Calibration at NMISA

Uploaded by

Copyright:

Available Formats

Presenter: Bongani Ndlovu

The uncertainty evaluation for the Date: 09/10/2018

• Thin graduated hollow tube

• Over time, small drifts in scale occur due to

• Consists of 200 g balance with 0,01 mg readability,

• Wright JD, Bean VE and Aguilera J, 2010. NIST calibration services

• Hydrometer weighed in air:

• A Picard et al., Metrologia 45 (2008) 149–155

• 𝑎5 = 999,972 kg/m^3 assumed for tap water

• M Tanaka et al. Metrologia, 2001, 38, 301-309

• Repeatability of the measurement

You might also like