Data sheet SSAB Domex Tube 460MH 2017-04-25

SSAB Domex Tube 460MH

General Product Description
SSAB Domex Tube 460MH is high strength structural hollow section.
It meets or exceeds the requirements of EN 10219 and is available in circular, rectangular, square and special shapes. Customized shapes and other tailoring
options are available upon request. It is typically used in advanced engineering and construction where weight reduction, lower costs and safety are
important.
SSAB Domex Tube 460MH is manufactured by cold forming and high frequency welding from clean, high quality environmentally friendly steel by modern
and efficient tube lines.SSAB Domex Tube 460MH is high strength structural hollow section. It meets or exceeds the requirements of EN 10219 and is
available in circular, rectangular, square and special shapes. Customized shapes and other tailoring options are available upon request. It is typically used in
advanced engineering and construction where weight reduction, lower costs and safety are important. SSAB Domex Tube 460MH is manufactured by cold
forming and high frequency welding from clean, high quality environmentally friendly steel by modern and efficient tube lines.

Dimension Range
SSAB Domex Tube 460 MH is available at circular, square and rectangular shapes.

Circular 42.4 - 323.9 mm

Square 40x40 - 300x300 mm
Rectangular 50x30 - 400x200 mm
Wall thickness 2.0 - 12.50 mm
Mill length 6000 - 12 000/18 000 mm
Other shapes and sizes are available upon request.

Dimensions
Circular
Diameter 2.0mm (kg/m) 3.0mm (kg/m) 4.0mm (kg/m) 5.0mm (kg/m) 6.0mm (kg/m) 8.0mm (kg/m) 10.0mm 12.5mm
(kg/m) (kg/m)
42.4 mm 1.99 2.19
48.3 mm 2.28 3.35 4.37
60.3 mm 2.88 4.24 5.55 6.82
76.1 mm 5.41 7.11
88.9 mm 6.36 8.38 10.4
101.6 mm 7.29 9.63 11.9
108 mm 7.77 10.3 12.7
114.3 mm 8.23 10.9 13.5
127 mm 9.17 12.1 15.0
133 mm 9.62 12.7 15.8
139.7 mm 10.1 13.4 16.6 19.8 26.0 32.0
152.4 mm 14.6 18.2
159 mm 15.3 19.0 22.6 x x
168.3 mm 16.2 20.1 24.0 31.6 39.0
193.7 mm 23.3 27.8 36.6 45.3
219.1 mm 26.4 31.5 41.7 51.6
273 mm 33.1 39.5 52.3 64.9 80.3
323.9 mm 47.0 62.3 77.4 96.0
 Data sheet SSAB Domex Tube 460MH 2017-04-25

Square
Height x Width 2.0mm (kg/m) 3.0mm (kg/m) 4.0mm (kg/m) 5.0mm (kg/m) 6.0mm (kg/m) 8.0mm (kg/m) 10.0mm 12.5mm
(kg/m) (kg/m)
40 x 40 mm 2.31 3.30 4.20
50 x 50 mm 2.93 4.25 5.45
60 x 60 mm 3.56 5.19 6.71 8.13
70 x 70 mm 6.13 7.97 9.70
80 x 80 mm 7.07 9.22 11.3 13.2
90 x 90 mm 8.01 10.5 12.8 15.1
100 x 100 mm 8.96 11.7 14.4 x 21.4
110 x 110 mm 9.90 13.0
120 x 120 mm 10.8 14.3 17.6 20.8 26.4
140 x 140 mm 16.8 20.7 24.5 31.4 38.1
150 x 150 mm 18.0 22.3 24.5 31.4 41.3
160 x 160 mm 23.8 28.3 36.5 44.4 52.6
180 x 180 mm 27.0 32.1 41.5 50.7 60.5
200 x 200 mm 30.1 35.8 46.5 57.0 68.3
250 x 250 mm 45.2 59.1 72.7 88.0
300 x 300 mm 54.7 71.6 88.4 108

Rectangular
Height x Width 2.0mm (kg/m) 3.0mm (kg/m) 4.0mm (kg/m) 5.0mm (kg/m) 6.0mm (kg/m) 8.0mm (kg/m) 10.0mm 12.5mm
(kg/m) (kg/m)
50 x 30 mm 2.31 3.30 4.20
60 x 40 mm 2.93 4.25 5.45 6.56
70 x 50 mm 3.56 5.19 6.71 8.13
80 x 40 mm 3.56 5.19 6.71 8.13
80 x 60 mm 6.13 7.97 9.70
90 x 50 mm 6.13 7.97 9.70
100 x 50 mm 6.60 8.59 10.5
100 x 60 mm 7.07 9.22 11.3
100 x 80 mm 8.01 10.5 12.8
120 x 50 mm 7.54 9.85 12.1
120 x 60 mm 8.01 10.5 12.8
120 x 80 mm 8.96 11.7 14.4
120 x 100 mm 9.90 13.0 16.0
140 x 80 mm 9.90 13.0 16.0
150 x 100 mm 11.3 14.9 18.3 21.7 27.7
160 x 80 mm 14.3 17.6 20.8 26.4
160 x 90 mm 14.9 18.3 21.7 27.7
180 x 100 mm 20.7 24.5 31.4 38.1
200 x 100 mm 22.3 26.4 34.0 41.3
200 x 120 mm 23.8 28.3 36.5 44.4 52.6
250 x 100 mm 26.18 31.11 40.23 49.11 x
250 x 150 mm 30.1 35.8 46.5 57.0 68.3
300 x 200 mm 45.2 59.1 72.7 88.0
400 x 200 mm 54.7 71.6 88.4 108
 Data sheet SSAB Domex Tube 460MH 2017-04-25

Mechanical Properties
Yield Strength Rp0.2 Tensile Strength Rm Elongation A 5 2) Charpy-V -40°C 10x10 mm test
(min MPa) (MPa) (min %) specimen 1)
(min J)
460 530 - 720 17 27
Mechanical properties meet or exceed the requirements of EN 10219.
The mechanical properties for rectangular hollow sections are tested by SSAB on the longer side of the cross section.
1)Impact testing according to EN ISO 148-1 is performed on thicknesses ≥ 6mm. The specified minimum value corresponds to a full-size specimen.
2) The hollow sections with D/T < 15 (round) or (B + H)/2T < 12,5 (rectangular and square), the minimum value of elongation is reduced by 2.

Chemical Composition (ladle analysis)

C Si Mn P S Al tot Nb V Ti
(max %) (max %) (max %) (max %) (max %) (min %) (max %) (max %) (max %)
0.16 0.25 1.70 0.020 0.012 0.020 0.090 0.120 0.060
Chemical composition meets or exceeds the requirements of EN 10219.
The steel is aluminium-killed.

Carbon equivalent

CEV 0.40
(max %)
CEV value exceeds the requirements of EN 10219.
CEV=C+Mn/6+(Cr+Mo+V)/5+(Ni+Cu)/15

Tolerances
Characteristic Circular hollow sections
Tolerances meet or exceed the requirements of EN 10219
Outside diameter (D) 1) ±1%, however a minimum of ±0.5 mm and a maximum of ±10 mm
Out-of-roundness 2%, when D/T ≤ 100
Thickness (T) When D ≤ 323.9 mm: -5%/+10%, with a minimum of ±0.2 mm and maximum
±0.5 mm
When 355.6 ≤ D ≤ 406.4 mm3): ±10%, when T ≤ 5 mm / ±0.5 mm, when T > 5
mm
When D > 406.4 mm3): ±10%, with a maximum of ±2 mm
Straightness 0.20% of total length and 3 mm over any 1 m length
Mass per unit length Individual tube: ±6%
Mill length 0/+50 mm, 6000 ≤ L ≤ 12000 - 18000 mm (standard lengths 6000 & 12000
mm)
Exact length Agreed at the time of enquiry and order
1) All external dimensions are measured with a minimum distance from the end of the section. The distance must be a minimum of 100 mm.
 Data sheet SSAB Domex Tube 460MH 2017-04-25

Characteristic Square hollow sections

Tolerances meet or exceed the requirements of EN 10219
Outside dimensions (B, H) 1) When B, H < 100 mm ±1 % minimum ±0.5 mm
When 100 mm ≤ B, H ≤ 200 mm: ±0.8%
When B, H > 200 mm: ±0.6%
Thickness (T) -5%/ +10 %, with a minimum of ±0.2 mm and maximum ±0.5 mm
External corner profile When T ≤ 6 mm: 1.6 x T–2.4 x T
When 6 mm < T ≤ 10 mm: 2.0 x T-3.0 x T
When T > 10 mm: 2.4 x T–3.6 x T
Squareness of side 90° ±1°
Concavity/convexity 0.8%, with a minimum of 0.5 mm
Twist 2 mm + 0.5 mm/m
Straightness 0.15% of total length and 3 mm over any 1 m length
Mass per unit length Individual tube: ±6%
Mill length 0/+50 mm, 6000 ≤ L ≤ 12000 - 18000 mm (standard lengths 6000 & 12000
mm)
Exact length Agreed at the time of enquiry and order
1) All external dimensions are measured with a minimum distance from the end of the section. The distance must be a minimum of 100 mm.

Characteristic Rectangular hollow sections

Tolerances meet or exceed the requirements of EN 10219
Outside dimensions (B, H) 1) When B, H < 100 mm ±1 % minimum ±0.5 mm
When 100 mm ≤ B, H ≤ 200 mm: ±0.8%
When B, H > 200 mm: ±0.6%
Thickness (T) -5%/ +10 %, with a minimum of ±0.2 mm and maximum ±0.5 mm
External corner profile When T ≤ 6 mm: 1.6 x T–2.4 x T
When 6 mm < T ≤ 10 mm: 2.0 x T-3.0 x T
When T > 10 mm: 2.4 x T–3.6 x T
Squareness of side 90° ±1°
Concavity/convexity 0.8%, with a minimum of 0.5 mm
Twist 2 mm + 0.5 mm/m
Straightness 0.15% of total length and 3 mm over any 1 m length
Mass per unit length Individual tube: ±6%
Mill length 0/+50 mm, 6000 ≤ L ≤ 12000 - 18000 mm (standard lengths 6000 & 12000
mm)
Exact length Agreed at the time of enquiry and order
1) All external dimensions are measured with a minimum distance from the end of the section. The distance must be a minimum of 100 mm.

Contact Information
www.ssab.com/contact

The English version of this document shall prevail in case of discrepancy. Minor changes and updates to the document may occur, please download
the latest version of this document at www.ssab.com
SSAB, Strenx, Hardox, Docol, GreenCoat, Toolox, Armox, Ramor, SSAB Domex, SSAB Laser, Raex, Duroxite are trademarks owned by the SSAB group
of companies.