Note: Printed copy is UNCONTROLLED.
ENG ECN NO.
REV DESCRIPTION APP’L AND DATE
B1 B1 A ISSUED 89-3723
CO MHD 09/13/89
B1 ROUND HANDLE GRIP WAS SQUARE 97-0730
B2 UPDATED TITLE BLOCK 11/18/97
LWP
INSTRUCTIONS FOR THE INSTRUCTIONS FOR MODEL THE
MODEL NUMBERS NO. 48072 AND 48272
48072 AND 48272. INDUSTRIES, LLC WHEN BRAKE CIRCUIT IS USED. INDUSTRIES, LLC
LESS BRAKE CIRCUIT 2600 LANIER DRIVE
MADISON, INDIANA 47250
(SEE REVERSE SIDE FOR 2600 LANIER DRIVE
MADISON, INDIANA 47250
(SEE REVERSE SIDE FOR WIRING WIRING INSTRUCTIONS WHEN
COLUMN CLAMP FITS
INSTRUCTIONS WHEN BRAKE CIRCUIT BRAKE CIRCUIT IS NOT USED). 2.375 DIA. COLUMN
(SUPPLIED UNASSEMBLED)
IS REQUIRED) COLUMN CLAMP FITS
2.375 DIA. COLUMN HAZARD WARNING FUNCTION
(SUPPLIED UNASSEMBLED)
HAZARD WARNING FUNCTION
PULL OUT FOR
HAZARD WARNING FUNCTION
PULL OUT FOR
HAZARD WARNING FUNCTION
MOUNTING AND WIRING INSTRUCTIONS
MOUNTING AND WIRING INSTRUCTIONS NOTE: PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION.
NOTE: PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION.
1) MOUNTING OF TURN SIGNAL SWITCH B) The flasher and flasher connector are not
1) MOUNTING OF TURN SIGNAL SWITCH B) For pilot bulb replacement on 12 volt systems A) Mount switch to steering column with the tube supplied with the switch. They may be
A) Mount switch to steering column with the tube use a no. 53 bulb. clamp or mounting adapters which are purchased from GROTE MFG. CO., flasher
clamp or mounting adapters which are C) To replace the pilot light bulb place the provided. (see fig. #1) connector # 16-9009-01 and terminal #
provided. (see fig. #1) handle in neutral position and remove the cap 31-5030-01 (3 req’d). Use GROTE flasher
by placing fingers on each side of switch 2) WIRING THE TURN SIGNAL SWITCH HARNESS # 44540 (25 amp) on 12 volt,
2) WIRING THE TURN SIGNAL SWITCH HARNESS cap and gently prying outward while lifting A) Slide loom provided over wires from connector 3 terminal systems. For maximum system
A) Slide loom provided over wires from connector at the sme time. before connection to vehicle wiring. performance use GROTE # 44670 3 terminal
before connection to vehicle wiring. Remove snap on bulb shield and replace bulb. B) Connect the red wire from the harness to flasher.
B) Connect the black wire from the harness to Replace bulb shield making sure index tab at the right front turn lamp. C) For pilot bulb replacement on 12 volt
the right turn lamps. back is located in the die-cast handle re- C) Connect the green wire from the harness to systems use a # 53 bulb.
C) Connect the gray wire from the harness to tainer. Switch cap will snap in place by the left front turn lamp. D) To replace the pilot light bulb place the
the left turn lamps. gently pushing it down over the switch with D) Connect the black wire from harness to the handle in neutral position and remove the
D) Connect the white wire to a good ground on the handle in neutral position. right rear stop/turn lamp. cap by placing fingers on each side of
the vehicle. D) To operate the hazard warning function pull E) Connect the gray wire from the harness to switch cap and gently prying outward while
E) Connect the yellow wire from the switch to the chrome hazard handle outward. To left rear stop/turn lamp. lifting at the same time.
the flasher terminal marked "L". cancel the hazard warning function move the F) Connect the white wire to a good ground on Remove snap on bulb shield and replace bulb.
F) Connect the blue wire from the switch to the turn handle to the left or right turn the vehicle. Replace bulb shield making sure index tab at
flasher terminal marked "P". position. G) Connect the gray wire with black stripe to back is located in the die-cast handle re-
G) Connect a hot wire from the battery to the E) Hot wires from battery to flasher must be the brake switch terminal opposite tainer. Switch cap will snap in place by
flasher terminal marked "X". fused for component protection in the hot wire from the battery. gently pushing it down over the switch with
H) Plug connector on switch harness to terminals case of a dead short. H) Connect the yellow wire from switch to the handle in neutral position
on the bottom of the switch. (Use a fuse rated at 20amps max.) the flasher terminal marked "L". E) To operate the hazard warning function
NOTE: ORIETATION OF CONNECTOR IS CRITICAL. I) Connect the blue wire from the switch to the pull the chrome hazard handle outward. To
4) WIRING INSTRUCTIONS ARE BASED ON THE flasher terminal marked "P". cancel the hazard warning function move
3) NOTES HARNESS SUPPLIED WITH THE 48072 SWITCH J) Connect a hot wire from the battery the turn handle to the left or right turn
A) The flasher and flasher connector are not OR THE 69680 HARNESS. (WIRES NOT USED ON THE to the flasher terminal marked "X". position.
supplied with the switch. They may be FOUR WIRE SYSTEM CAN BE CUT OFF). K) Plug connector on harness to terminals F) Hot wires from battery to flasher and
purchased from GROTE MFG. CO., flasher on bottom of switch. brake switch must be fused for component
connector # 16-9009-01 and terminal NOTE: ORIETATION OF CONNECTOR IS CRITICAL. protection in case of a dead short.
# 31-5030-01 (3 req’d). Use GROTE flasher (Use a fuse rated at 20amps max.)
# 44540 (25 amp) on the 12 volt, 3 terminal 3) NOTES
systems. For maximum system performance HAZ. A) If the vehicle has the turn indicator lights 4) WIRING INSTRUCTIONS ARE BASED ON THE
use GROTE # 44670 (3 terminal) flasher. on the dash, the blue pilot wire will not HARNESS SUPPLIED WITH THE 48072 SWITCH
If the vehicle has the turn indicator lights be used. The switch pilot light must be used OR THE 69680 HARNESS.
on the dash the blue pilot wire will not be used. with a (3) prong flasher.
The switch pilot light must be used with
a (3) prong flasher.
HAZ.
STEERING COLUMN
RIGHT FRONT TURN STEERING COLUMN
MOUNTING ADAPTER EXISTING TRUCK
PILOT-BLUE
(2 REQ’D) MOUNTING ADAPTER EXISTING TRUCK
MTG. BRACKET (2 REQ’D)
P
HOT TURN-YELLOW MTG. BRACKET
RIGHT REAR TURN-
X L
BLACK
RIGHT FRONT TURN-RED
+ PILOT-BLUE
FUSE
BATTERY P
HOT TURN-YELLOW
- L
RIGHT REAR TURN- TRADE SECRET
X BLACK DO NOT REPRODUCE, USE OR DISCLOSE THIS DOCUMENT
OR THE INFORMATION HEREIN.
LEFT REAR TURN- COPYRIGHT (UNPUBLISHED) GROTE INDUSTRIES, LLC
GRAY +
FUSE
BATTERY BRAKE
SWITCH
GCC THIRD ANGLE
- DENOTES GROTE PROJECTION
GROUND-WHITE CONTROL CHARACTERISTIC
HOT BRAKE
GRAY W/BLACK STRIPE
LEFT FRONT TURN
#8-32 SCREW
LEFT REAR TURN- DR. BY: C. O’NEAL SCALE: NONE UNITS: IN
GRAY #8-32 SCREW
3/8" LONG
(2 REQ’D) 3/8" LONG DATE: 09/13/89 CK’D BY:
(2 REQ’D)
MATERIAL NO.
GROUND-WHITE
NOTE: NOTE:
PLACE INSERTS IN MTG. BRACKET LEFT FRONT TURN-GREEN PLACE INSERTS IN MTG. BRACKET N/A
AND DRIVE TWO SCREWS INTO AND DRIVE TWO SCREWS INTO
INSERTS AS SHOWN. INSERTS AS SHOWN. MAT’L DESCRIPTION
FIGURE #1 FIGURE #1 N/A
TITLE
WIRING DIAGRAM WIRING DIAGRAM
FORM NO. 56-8001-61 REV. "B" INSTRUCTION SHEET
GROTE INDUSTRIES, LLC
B1 B1 MADISON, INDIANA U.S.A.
SIZE PART/DWG NO. REV. SHT #
B2
C 56-8001-61 B 1 OF 1
SYSTEM/REV. PROJECT #: NO
MEDUSA 14 3D DATA: NO
