STRUCTURAL CALCULATIONS

PROJECT: SP INFOCITY, CHENNAI

(MS DESIGN FOR COPING ACP)

SP FABRICATORS PVT LTD

CHAPTER 1: PROJECT DETAILS

SP FABRICATORS PVT LTD

 STRUCTURAL CALCULATIONS
PROJECT: SP INFOCITY, CHENNAI

PROJECT DETAILS :
PROJECT : SP INFOCITY

LOCATION : CHENNAI

CLIENTS : SPCL

ARCHITECTS : HAFEEZ CONTRACTOR/ ESKAY ARCHITECTS

SP FABRICATORS PVT LTD.

CHAPTER 2: WIND LOAD

SP FABRICATORS PVT LTD

 STRUCTURAL CALCULATION
PROJECT: SP INFOCITY, CHENNAI

As per Tender

Design Wind Pressure= 2.00 kN/m2

SP FABRICATORS PVT LTD

 CHAPTER 3: DESIGN OF MS
FRAME WORK FOR COPING ACP

SP FABRICATORS PVT LTD

 STRUCTURAL CALCULATION
PROJECT: SP INFOCITY, CHENNAI

MEMBER DESIGN - 1
Max Wind Pressure
2
W = 200.0 Kg/m (AS PER IS 875 PART III - 1987)
2
= 2 Kn/m

For Steel
3
Density = 78.5 Kn/m
2
Elasticity (E) = 200000 N/mm

Mass Properties of Sections used

I] ALUMINIUM SQUARE TUBE -40 X 40 X 2

Breadth (b) = 40.00 mm
Depth (d) = 40.00 mm
Thickness (t) = 2.00 mm
2
Area of the tube = 3.04 cm
Self Weight = 2.39 Kg/m

HORIZONTAL - ISMC 100

4
Major Moment of Inertia (Ixx) = 186.70 cm
4
Minor Moment of Inertia (Iyy) = 26.90 cm
3
Major Sectional Modulus (Zxx) = 37.30 cm
3
Minor Sectional Modulus (Zyy) = 7.50 cm
2
Crossectional Area (A) = 11.70 cm
Self Weight = 9.20 Kg/m

Al Frame for
coping ACP

ISMC 100

1.50m

Transverse
members RCC
1.50m

ACP Spans
Span between two Al frames(S1) = 1.5 m
Span between transverse members(S2) = 0.5 m

2
Weight of ACP & fittings assumed per Sqmt (Wd) = 0.1 Kn/m
2
Accidental human load (Wh) = 0.75 Kn/m
2
Wind load (Ww) = 2 Kn/m
2
= 0.1 Kn/m

SP FABRICATORS PVT LTD

 STRUCTURAL CALCULATION
PROJECT: SP INFOCITY, CHENNAI

Calculation of Loading on one MS frame (DL, LL & WL)

UDL due to Wind load (ww) = 3 Kn/m (W w x S)
UDL due to Accidental human load load (w
h) = 1.125 Kn/m (W h x S)
UDL due to Dead load (ww) = 0.15 (W d x S)

Analysing the structure in STAAD imposing the above loading

Max Bending Moment (M) = 0.74 Kn-m (Refer Staad file)
Max Shear Force (V) = 2.20 Kn (Refer Staad file)
Max Reaction (Ry) = 2.20 Kn (Refer Staad file)
Support moment (MZ) = 0.74 Kn (Refer Staad file)

CHECK FOR STRESSES

REFER DETAILED CALCULATION SHEETS

CHECK FOR DEFLECTION

Span of Cantilever frame = 675 mm
Max Deflection = 0.24 mm (From STAAD Output)

Permissible Deflection is lesser of Span/ 325 = 2.08 mm

Therefore Permissible Deflection = 2.08 mm
> 0.24 mm (Actual Deflection)

INDUCED DEFLECTION IS LESS THEN PERMISSIBLE DEFLECTION,

HENCE PROFILE IS SAFE IN DEFLECTION

SP FABRICATORS PVT LTD

CHAPTER 4: CHECK FOR STRESSES

SP FABRICATORS PVT LTD

 STRUCTURAL CALCULATION
PROJECT: SP INFOCITY, CHENNAI

CHECK FOR STRESSES

[ As per IS:800]

MS CANTILEVER FRAME

Design Parameters & Constants

2
Modulus of Elasticity (E) = 200000.00 N/mm
2
Tensile Yeild Strength (Fy) = 250.00 N/mm
Permissible Stresses
2
Axial (Fa) = 85.00 N/mm
2
Bending tensile stress (Fbt) = 165.00 N/mm
2
Bending Compressive stress (Fbc) = 165.00 N/mm
2
Shear (Fv) = 100.00 N/mm
2
Combined Bending & Shear = 225.00 N/mm

Member Sectional Properties Member Forces

(Refer Calc Sheets)
b = 5.00 cm d = 10.00 cm P = 0.00 Kn
2
t = 0.47 cm A = 11.70 cm Mx = 0.74 Kn-m
4 3
Ixx = 186.70 cm Zxx = 37.30 cm My = 0.00 Kn-m
4 3
Iyy = 26.90 cm Zyy = 7.50 cm Vx = 0.00 Kn
rx = 3.99 cm ry = 1.52 cm Vy = 2.20 Kn

Calculated Stresses
2
Axial Compressive Stress (fc) = 0.00 N/mm (P/A)

Bending Compressive Stress

2
Major Direction (fbcx) = 19.89 N/mm (Mx/Zx)
2
Minor Direction (fbcy) = 0.00 N/mm (My/Zy)

Bending Tensile Stress

2
Major Direction (fbtx) = 19.89 N/mm (Mx/Zx)
2
Minor Direction (fbty) = 0.00 N/mm (My/Zy)

Shear Stress
2
Major Direction (fsx) = 0.00 N/mm (Vx/2dt)
2
Minor Direction (fsy) = 4.68 N/mm (Vy/2bt)

SP FABRICATORS PVT LTD

 STRUCTURAL CALCULATION
PROJECT: SP INFOCITY, CHENNAI

Permissible Stresses (Check for Buckling)

[Using IS:800]

Effective Length
Lx = 675.00 mm
Ly = 675.00 mm
Therefore Slenderness Ratios
λx = 16.90 (Lx/rx)
λy = 44.52 (Ly/ry)

For λ = 44.52 ,From Fig-1, IS:8147, Material 63400-WP

Permissible Compressive Stresss

2
Fc = 165.00 N/mm

Bending, Extreme Fibre Tensile Stress

[Using IS:800]

Permissible Bending Tensile Stresss

2
Fbt = 165.00 N/mm

Shear
[Using IS:800]

Permissible Shear Stresss

2
Fs = 100.0 N/mm

Check for Stresses

1) Combined Bending & Axial Compression

fc fbcx fbcy 0.00 19.9 0.00

+ + = + + = 0.12 < 1.00
Fc Fbc Fbt 165.00 165.00 165.00

2) Combined Bending & Shear

2 2 0.5 2 2
(fbcx + 3fsx ) = 19.9 N/mm < 225 N/mm (0.9Fty)

2 2 0.5 2 2
(fbcy + 3fsy ) = 8.1 N/mm < 225 N/mm (0.9Fty)

3) Shear Stress

fsx fsy 0.00 4.68

+ = + = 0.047 < 1.25
Fs Fs 100.00 100.00

SINCE ALL THE EQUATIONS ARE SATISFIED, SECTION IS OK

SP FABRICATORS PVT LTD

STAAD OUTPUT FOR MS
FRAME

SP FABRICATORS PVT LTD

 STRUCTURAL CALCULATION
PROJECT: SP INFOCITY, CHENNAI

INPUT FILE: Coping MS frame-Channel.STD

1. STAAD SPACE
2. START JOB INFORMATION
3. ENGINEER DATE 24-MAY-08
4. END JOB INFORMATION
5. INPUT WIDTH 79
6. *SET NL 1
7. UNIT METER KN
8. JOINT COORDINATES
9. 1 0 0 0; 2 0.675 0 0
10. MEMBER INCIDENCES
11. 1 1 2
12. DEFINE MATERIAL START
13. ISOTROPIC STEEL
14. E 2.05E+008
15. POISSON 0.3
16. DENSITY 76.8195
17. ALPHA 1.2E-005
18. DAMP 0.03
19. END DEFINE MATERIAL
20. MEMBER PROPERTY INDIAN
21. 1 TABLE ST ISMC100
22. CONSTANTS
23. MATERIAL STEEL MEMB 1
24. SUPPORTS
25. 1 FIXED
26. LOAD 1 SELF
27. SELFWEIGHT Y -1
28. LOAD 2 D.L
29. MEMBER LOAD
30. 1 UNI GY -0.15
31. LOAD 3 ACCIDENTAL HUMAN LOAD
32. MEMBER LOAD
33. 1 UNI GY -1.125
34. LOAD 4 W.L
35. MEMBER LOAD
36. 1 UNI GY -3
37. LOAD COMBINATION 51
38. 1 1.2 2 1.0 4 1.0
39. LOAD COMBINATION 52
40. 1 1.2 2 1.0 3 1.0

SP FABRICATORS PVT LTD

 STRUCTURAL CALCULATION
PROJECT: SP INFOCITY, CHENNAI

STAAD SPACE -- PAGE NO. 2

41. PERFORM ANALYSIS

PROBLEM STATISTICS
-----------------------------------

NUMBER OF JOINTS/MEMBER+ELEMENTS/SUPPORTS = 2/ 1/ 1
ORIGINAL/FINAL BAND-WIDTH= 1/ 1/ 6 DOF
TOTAL PRIMARY LOAD CASES = 4, TOTAL DEGREES OF FREEDOM = 6
SIZE OF STIFFNESS MATRIX = 1 DOUBLE KILO-WORDS
REQRD/AVAIL. DISK SPACE = 12.0/ 10858.9 MB, EXMEM = 1098.9 MB

42. PRINT MEMBER FORCES LIST 1

STAAD SPACE -- PAGE NO. 3

SP FABRICATORS PVT LTD

 STRUCTURAL CALCULATION
PROJECT: SP INFOCITY, CHENNAI

MEMBER END FORCES STRUCTURE TYPE = SPACE

-----------------
ALL UNITS ARE -- KN METE

MEMBER LOAD JT AXIAL SHEAR-Y SHEAR-Z TORSION MOM-Y MOM-Z

1 1 1 0.00 0.06 0.00 0.00 0.00 0.02

2 0.00 0.00 0.00 0.00 0.00 0.00
2 1 0.00 0.10 0.00 0.00 0.00 0.03
2 0.00 0.00 0.00 0.00 0.00 0.00
3 1 0.00 0.76 0.00 0.00 0.00 0.26
2 0.00 0.00 0.00 0.00 0.00 0.00
4 1 0.00 2.03 0.00 0.00 0.00 0.68
2 0.00 0.00 0.00 0.00 0.00 0.00
51 1 0.00 2.20 0.00 0.00 0.00 0.74
2 0.00 0.00 0.00 0.00 0.00 0.00
52 1 0.00 0.93 0.00 0.00 0.00 0.32
2 0.00 0.00 0.00 0.00 0.00 0.00

************** END OF LATEST ANALYSIS RESULT **************

43. PRINT SUPPORT REACTION LIST 1

STAAD SPACE -- PAGE NO. 4

SUPPORT REACTIONS -UNIT KN METE STRUCTURE TYPE = SPACE

-----------------

JOINT LOAD FORCE-X FORCE-Y FORCE-Z MOM-X MOM-Y MOM Z

1 1 0.00 0.06 0.00 0.00 0.00 0.02

2 0.00 0.10 0.00 0.00 0.00 0.03
3 0.00 0.76 0.00 0.00 0.00 0.26
4 0.00 2.03 0.00 0.00 0.00 0.68
51 0.00 2.20 0.00 0.00 0.00 0.74
52 0.00 0.93 0.00 0.00 0.00 0.32

************** END OF LATEST ANALYSIS RESULT **************

44. PRINT JOINT DISPLACEMENTS

STAAD SPACE -- PAGE NO. 5

SP FABRICATORS PVT LTD

 STRUCTURAL CALCULATION
PROJECT: SP INFOCITY, CHENNAI

JOINT DISPLACEMENT (CM RADIANS) STRUCTURE TYPE = SPACE

------------------

JOINT LOAD X-TRANS Y-TRANS Z-TRANS X-ROTAN Y-ROTAN Z-ROTAN

1 1 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000

2 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
3 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
4 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
51 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
52 0.0000 0.0000 0.0000 0.0000 0.0000 0.0000
2 1 0.0000 -0.0007 0.0000 0.0000 0.0000 0.0000
2 0.0000 -0.0011 0.0000 0.0000 0.0000 0.0000
3 0.0000 -0.0083 0.0000 0.0000 0.0000 -0.0002
4 0.0000 -0.0222 0.0000 0.0000 0.0000 -0.0004
51 0.0000 -0.0241 0.0000 0.0000 0.0000 -0.0004
52 0.0000 -0.0102 0.0000 0.0000 0.0000 -0.0002

************** END OF LATEST ANALYSIS RESULT **************

45. PARAMETER
46. CODE INDIAN
47. CHECK CODE MEMB 1
STAAD SPACE -- PAGE NO. 6

STAAD.Pro CODE CHECKING - (ISA )

***********************

ALL UNITS ARE - KN METE (UNLESS OTHERWISE NOTED)

MEMBER TABLE RESULT/ CRITICAL COND/ RATIO/ LOADING/

FX MY MZ LOCATION
=======================================================================

1 ST ISMC100 PASS IS-7.1.1(A) 0.127 51

0.00 T 0.00 0.74 0.00

************** END OF TABULATED RESULT OF DESIGN **************

48. STEEL TAKE OFF LIST 1

STAAD SPACE -- PAGE NO. 7

SP FABRICATORS PVT LTD

 STRUCTURAL CALCULATION
PROJECT: SP INFOCITY, CHENNAI

STEEL TAKE-OFF
--------------

PROFILE LENGTH(METE) WEIGHT(KN )

ST ISMC100 0.68 0.061

PRISMATIC STEEL 0.00 0.000
----------------
TOTAL = 0.061

************ END OF DATA FROM INTERNAL STORAGE ************

49. FINISH

SP FABRICATORS PVT LTD

BRACKET & ANCHOR
CALCULATIONS

SP FABRICATORS PVT LTD

 STRUCTURAL CALCULATIONS
PROJECT: SP INFOCITY, CHENNAI

BRACKET DESIGN
Forces
Verticle (V) = 2.20 Kn Sh
Support moment (M) = 0.74 Knm

Horizontal Plate
D2
Width (B 2) = 200.00 mm
Depth (D 2) = 120.00 mm
Thickness (t 2) = 8.00 mm

B2
Forces

Vertical force (F y) = 2.20 Kn (V)

Support moment (M) = 0.74 Knm (M)

TOP VIEW

V
Bending Moments
Mx = 0.740 Kn-m ( Fy x e z )
My = 0.000 Kn-m ( Fz x e x )
D2
Mz = 0.000 Kn-m ( Fy x e x )

Plate Modulus of section

4 2
Zx = 480000.00 mm (B2xD2 /6)
SIDE VIEW
4 2
Zy = 800000.00 mm (D2xB2 /6)

2
Max Pressure at base (p) = 0.08 N/mm ( ( F z / ( B 2 x D2 )) x ( 1 + M x/Zx + My/Zy ) )

For M25 concrete

2
Permissible Stress in direct compression (s cdc) = 6.0 N/mm
Hence Max pressure at base is OK

Max Plate Projection (s 2) = 80.00 mm

Anchor Edge distance (ed h) = 40.00 mm
Distance from plate (a d) = 40.00 mm (s2-edh)
Max Bending Moments
2
Due to compression (M 3) = ( p x s2 / 2 )
250.78 N-mm/mm
Due to tension (M 4) = ( H x a d/ 2xD2 )
123.33 N-mm/mm
Therefore max BM (M 5) = 250.78 N-mm/mm

2 2
Max Bending Stress = 23.51 N/mm ( 6M5 / t 2 )
2
< 165.00 N/mm ( Permissible Bending Stress for MS )

HENCE SAFE IN BENDING

SP FABRICATORS PVT LTD

 STRUCTURAL CALCULATIONS
PROJECT: SP INFOCITY, CHENNAI

Anchor Fasteners

No. of Anchors (na) = 2.00

Spacing
Horizontal (s h) = 120.00 mm
Vertical (s v) = 0.00 mm

Edge Distance
Horizontal (ed h) = 40.00 mm
Vertical (ed v) = 60.00 mm

Forces
Fy = 2.20 Kn
Mx = 0.74 Knm
Moments
Mx = 0.740 Kn-m
My = 0.000 Kn-m
Mz = 0.000 Kn-m

Max Tensile Force Per Anchor = 0.370 kN

Max Shear Per Anchor = 1.100 kN

Provide 2- Nos.ARROW - M10 WITH EFFECTIVE ANCHORAGE OF 50mm

SP FABRICATORS PVT LTD