12/7

Price: $12.50
TECHNICAL INFORMATION CATALOG

FASTENING
TECHNICAL GUIDE
Visit our website for the most up-to-date product information

C
TRIANGLE FASTENER
CORPORATION
Fastening Systems and Solutions For Commercial Construction
800.486.1832 | www.trianglefastener.com
 TECHNICAL
I N F O R M AT I O N

The purpose of this guide is to provide the most comprehensive fastening systems information available to the
industry. We have included many standard and hard to find specialty products.
You will find technical information on the majority of the fasteners listed. Additionally, we have developed
this section to include general information on fasteners, coatings, corrosion and stainless steel.
DISCLAIMERS
We have taken great care in compiling this information and made an effort to present its content accurately.
However, TFC is not responsible for any claims traceable to any errors (typographical or otherwise) as contained
in this guide.
The use of this guide is for general information only, and cannot be construed as a
substitute for competent professional advice or service. Any party considering
application or use of this information does so at their own risk and assumes any and all
liability arising from its application or use.

TRIANGLE FASTENER CORPORATION PAGE 2 800.486.1832 | www.trianglefastener.com

MD 239
Visit our website for the most up-to-date product and technical information!
 R
Fastener properties
C

Fastener Properties
Physical, mechanical and performance characteristics are material
related properties which collectively give the fastener its service
capability.

Physical Properties
Inherent in the raw material and remain unchanged or only slightly
altered in the fastener after its manufacture.

Mechanical Properties
Identify the reaction of a fastener to applied loads. Properties such as
hardness, ductility and tensile and yield strengths are all subject to
significant change as the raw material is processed into a finished
fastener.

Performance Properties
Functional design features manufactured into the fastener to assist it
to satisfy various service requirements. Properties of this type include
prevailing torque, driving torque, locking ability and sealing. Choice
of material and its metallurgical treatment influence magnitude rather
than the presence of a particular performance property.
Mechanical Properties
Tensile Strength - The maximum tension applied load a fastener
can support prior to fracture.

Yield Strength - A tension applied load at which a fastener

experiences a specified amount of permanent deformation: i.e., the material
has been stressed beyond its elastic limit and has entered its plastic zone.

Proof Load - The tension applied load supported by the fastener

without evidence of permanent deformation (about 90-93% of expected
material yield).

Hardness - A measure of ability to resist abrasion and indentation. For

carbon steel fasteners there is a close correlation between hardness and
tensile strength. A similar pattern exists for stainless and non-ferrous materials,
but it is not as precise as for carbon steels.

Ductility - Ability of a material to deform before it fractures. Elongation

and reduction of area are common criteria to evaluate ductility.

Toughness - A material's ability to resist damage when stressed by

impact or shock loading. Impact strength testing is rarely a testing requirement
outside of aerospace applications.

Shear Strength - The maximum load applied normal to a fastener's

axis that can be supported prior to fracture. Single shear is load occurring in
one transverse plane, thus cutting the fastener into two pieces. Double shear is
load applied in two planes, so that the fastener would be cut into three pieces.

Torsional Strength - Load usually expressed in terms of applied

torque at which fastener fails by being twisted off about its axis. The torsional
strength of the driving recess or wrenching surface is the torque which can be
sustained without damage to the tool/fastener interface resulting in an
undriveable condition.

Fatigue Strengt h - The maximum load a fastener can withstand

for a specified number of repeated applications prior to failure. For a single load
application to failure, the fatigue strength equals the static tensile strength. As
the load is reduced, the fastener endures an increasing number of loading
cycles until it reaches its other extreme of fatigue strength known as its
endurance limit, which is the cyclic load the fastener can accept and survive
indefinitely. Rarely used outside of aerospace applications, but helps compare
relative performance to resist dynamic loadings.

TRIANGLE FASTENER CORPORATION PAGE 3 800.486.1832 | www.trianglefastener.com

MD 240
Visit our website for the most up-to-date product and technical information!
 R
Drives and Head Styles
C

Drives

Slotted One-Way Phillips Phillips /Slot Phillips 1A/Slot Phillips/

Slot (Type 1) Combination (Type 1A) Combination Hex

Frearson Quadrex® Square 6 Lobe Hex Hex Hex

(Type 2) (Square/Phillips) (torx) Socket Washer

Head Styles

Binder Button Bugle Cheese Ext 6 Lobe Fillister 82˚ Flat

Head Head Head Head Washer Head Head Countersunk

82˚ U/C 100˚ Flat 90˚ Flat Ind Hex Trimmed Trimmed Hex Cap
Countersunk Countersunk Countersunk Head Hex Head Acorn Screw

Hex Ind Hex 82˚ Oval 90˚ Oval 82˚ Oval 90˚ Oval Pan Head
Washer Flange Head Head Head U/C Head U/C Head (for slotted
pan heads)

Pan Head Pan Head Round Round Head Full Crown Flat Top
(for recessed (for socket product) Head Round Round
Square Neck Washer Head Washer
pan heads)
Head

Socket Knurled Full Crown Flat Top Type UR Pancake Head

Head Head Truss Head Truss Head

TRIANGLE FASTENER CORPORATION PAGE 4 800.486.1832 | www.trianglefastener.com

MD 241
Visit our website for the most up-to-date product and technical information!
 R
Head features and washers
C

Under Head Configurations

Full Full Reverse Spinlock 6 “Nibs" Partial Chevron

Serrations Serrations Serrations Serrations Serrations Serrations

Thread
Blank
Dia.
Dia.

Reduced Knurled Ribbed Square Square Shoulder Full Body

Body Shoulder Neck Shoulder Neck

Washers

Beveled Conical External External Internal

Contersunk

Internal / Flat Slit Lock Split Wave Wave Washer

External

Ramp Conical Pyramidal Square® Cone Finishing Flanged

Finishing

TRIANGLE FASTENER CORPORATION PAGE 5 800.486.1832 | www.trianglefastener.com

MD 242
Visit our website for the most up-to-date product and technical information!
 R
Tapping Screw Points
C
Type Designations for Tapping Screws and Metallic Drive Screws
Abstract of ANSI/ASME B18.6.4 1981

Pictorial ANSI/ASME Manufacturer's

Representation Designation Designation

AB AB

B B

BP BP

BF BF

BT 25

Not recommended
for new designs C C

D 1

F F

G G

T 23

U U

TRIANGLE FASTENER CORPORATION PAGE 6 800.486.1832 | www.trianglefastener.com

MD 243
Visit our website for the most up-to-date product and technical information!
 R
Hole Sizes for Tapping Screws
C
Suggested hole sizes for tapping screws
Table 1 Suggested Hole Sizes for Thread Table 2 Suggested Hole Sizes for Types AB, B, and
Rolling Tapping Screws and Types D, F, G and T BP Thread Forming Tapping Screws and Types BF
Thread Cutting Tapping Screws and BT Thread Cutting Tapping Screws
Nominal Hole Closest Drill Size to Nominal Hole Closest Drill Size to
Screw Size Diameter Mean Hole Diameter Screw Size Diameter Mean Hole Diameter
Max Mean Min Drill Size Drill Dia. Max Mean Min Drill Size Drill Dia.
2 - 56 0.078 0.076 0.074 48 0.076 0-48 0.049 0.046 0.043 56 0.0465
2-64 0.077 1-42 .063 .059 .055 53 .0595
3 -48 0.090 0.087 0.084 44 0.086 2 - 32 .077 .072 .067 49 .073
3-56 0.089 3-28 .090 .084 .078 45 .082
4 - 40 0.100 0.097 0.094 41 0.096 4-24 .103 .096 .089 41 .096
4-48 0.100 5-20 .114 .107 .100 36 .1065
5-40 0.113 0.110 0.107 35 0.110 6-20 .124 .116 .108 32 .116
5-44 0.112 7-19 .138 .129 .120 30 .1285
6-32 0.123 0.119 0.115 31 0.120 8 - 18 .148 .138 .128 29 .136
6-40 0.124 10-16 .170 .159 .148 21 .159
8-32 0.150 0.146 0.141 20 0.147 12-14 .194 .182 .169 14 .182
8-36 0.148 1/4-14 226 .211 .196 4 .209
10 - 24 0.170 0.165 0.160 19 0.166 5/16-12 .289 .270 .251 I .272
10-32 0.177 0.172 0.167 11/64 0.1719 3/8-12 .356 .333 .310 0 .332
12-24 0.198 0.192 0.186 11 0.191 7/16-10 .413 .386 .359 w .386
12-28 0.196 1/2 - 10 .480 .449 A18 29/64 A531
1/4 - 20 0.228 0.221 0.214 2 0.221
1/4-28 0.230
Formula
5/16 - 18 0.289 0.281 0.273 K 0.281
Mean Hole Diameter = 0.98 x mean of thread major and minor
5/16-24 0.290
diameters. Tolerance is plus and minus 7 percent of mean hole
3/8 - 16 0.349 0.339 0.329 R 0.339
diameter.
3/8 - 24 0.353
7/16 - 14 0.409 0.397 0.385 X 0.397 Note
7/16-20 0.411
1/2 - 13 0.471 0.457 0.443 29/64 0.4531 As a general practice, tapping torque should equal approximately
1/2 - 20 0.475
70% of the fasteners torsional strength.

Formula
Mean Hole Diameter = 1.015 x basic thread pitch diameter. Tolerance is
plus and minus 3 percent of mean hole diameter No tolerances or drill
sizes are given for tapping screws with fine threads except for the No. 10
size. Use of fine thread tapping screws is not encouraged.

Torsional Strength Requirements For Tapping Screws

Minimum Torsional Strength, lb-in.
Nominal Types AB, B, BF, Types C, D, F, G and T
Screw Size HP and BT Coarse Fine
Thread Thread
2 4 5 6
3 9 9 10
4 13 13 15
5 18 18 20
6 24 23 27
7 30 – –
8 39 42 47
10 56 56 74
12 88 93 108
1/4 142 140 179
5/16 290 306 370
3/8 590 580 710
7/16 620 700 820
1/2 1020 1075 1285 Typical Torsional Strength Test
Fixture

TRIANGLE FASTENER CORPORATION PAGE 7 800.486.1832 | www.trianglefastener.com

MD 244
Visit our website for the most up-to-date product and technical information!
BLAZER Technical Data
R

DRILL SCREWS

BLAZER® engineering data

The following information is compiled to assist the design professional in selecting the
appropriate fastener for the application. Data supplied is compiled from fastener standards
and independent tests. An engineering professional should be consulted to determine
expected loads on the connection, environmental effects, and any other conditions that
could effect the performance of the fastener. Selecting a fastener is the responsibility of
the engineer and changes to a fastener should not be made without approval. Using the
wrong fastener can lead to failure.
TFC WILL not warranty, either expressed or implied,the use of this
information.
Technical data Thread Description Tensile Shear
Torsional
BLAZER® self-drilling fasteners
are produced and perform to
SAEJ78, ASME/ANSI 18.18. MINOR
and AISI TS-4-02 specifications.
Conforms to ICCESAC18
acceptance criteria for tapping
screw fasteners.
MAJOR

Physical Properties
REV.JES082712

Fastener Nominal Screw Major Minor Area Of Minor Torsional Tensile Shear
Diameter Diameter Diameter (inch) Diameter (inch) Dia. (sq in.) (Lb-In.) (Pounds) (Pounds)
Max Min Max Min
#6-20 0.138 0.139 0.135 0.104 0.099 0.0077 25 1,125 750
#8-18 0.164 0.166 0.161 0.122 0.116 0.0106 42 1,575 1,000
#10-16 0.190 0.189 0.183 0.141 0.135 0.0143 61 2,100 1,400
#10-24 0.190 0.190 0.182 0.144 0.137 0.0147 65 3,400 2,275
#12-14 0.216 0.215 0.209 0.164 0.157 0.0194 92 2,778 2,000
#12-24 0.216 0.216 0.209 0.189 0.185 0.0269 100 3,188 2,100
1/4-14 0.250 0.246 0.240 0.192 0.185 0.0269 150 3,850 2,600
1/4-20 0.250 0.250 0.242 0.218 0.214 0.0360 156 4,275 2,700
#18-9 0.306 0.306 0.300 0.217 0.209 0.0343 170 4,550 2,576
5/16-12 0.313 0.315 0.306 0.244 0.236 0.0702 290 5439 3264

English to Metric Formula to Use Gauge

Decimal Metric
Thickness
Decimal to Millimeters Decimal x 25.4
Material: C1018-C1022 / 410 SS 29 GA .013" .33mm
PSI to Newton / Millimeters² PSI x .007
Heat Treatment: Case Harden
28 GA .015" .38mm
Pounds Force to Newtons Pounds Force x 4.448
Case Hardness: 52-58 Rockwell C
26 GA .018" .46mm
Case Depth:
#6 Dia = .002” - .007” 24 GA .024" .61mm
DISCLAIMER: All test results and specifications
#8, #10, #12 Dia = .004” - .009” 22 GA .030" .76mm
are a result of laboratory tests. Appropriate
1/4” = .005” - .011” safety factors should be used by the user or 20 GA .036" .91mm
Core Hardness specifier. Determining the proper fastener is
Carbon Steel: 32-40 Rockwell C 18 GA .048" 1.22mm
the responsibility of the user or specifier.
410 Stainless: 42-48 Rockwell C Since application conditions vary and are 16 GA .060" 1.52mm
uncontrollable by TFC, we assume no liability
Ductility: 5 Degree minimum bend 14 GA .075" 1.91mm
for the use of this information.
12 GA .105" 2.67mm

Pullover test results 1/8" .125" 3.18mm

These pullover results are for self-sealing Note: Estimated pullover for fasteners 10 GA .135" 3.43mm

fasteners listed in this catalog. without sealing washers can be 1/4" .250" 6.35mm
calculated using the following formula 5/16" .312" 7.92mm
Pounds - Ultimate Average per AISI.
3/8" .375" 9.53mm

BOND-SEALER
Pullover force = 1.5 -x- Thickness of the 1/2" .500" 12.7mm
Steel FLANGE ZINC STAINLESS
member in contact with the screw head.
Thickness 12.7MM OD 15MM OD SEALER CAP HEAD CAP HEAD
-x- Larger of the screw head diameter or
22 ga 945 1,249 1,298 1,647 1,298
washer diameter. -x- Tensile strength of
24 ga 704 1,056 1,102 1,310 1,102 the member in contact with the screw
26 ga 519 654 692 794 692 head.

TRIANGLE FASTENER CORPORATION PAGE 8 800.486.1832 | www.trianglefastener.com

MD 18
Visit our website for the most up-to-date product and technical information!
BLAZER Technical Data
R

DRILL SCREWS
FASTENER PULLOUT LOADS | DRILL SCREWS
Fastener Because the tensile strength of the substrate dramatically affects the pullout of the
Pullout fastener, TFC provides published pullout results based on a calculation developed by AISI.

F The following fastener pullout loads were calculated per AISI S100 | Section 4 of the
Supplement No. 2 to the American Specification for the Design of Cold-Form Steel
Structural members (S100-07/S2-10).

Many tests were conducted with compressible fiberglass insulation placed between
steel sheet samples. It was determined by the results that the equations are valid for
steel connections including applications that use compressible insulation. Refer to AISI
S100 for more details.

• The pullout calculation requires the use of the nominal diameter of the screw and
the tensile strength of the substrate.
• Because substrate tensile and specific fastener details like point diameter affects
pullout loads, these pullout loads are conservative.

For tested values, contact Triangle Fastener to conduct actual

pullout tests based on a specific fastener style and the tensile
strength requirement of the substrate.

Pullout Loads | Ultimate in Pounds Force Rev 0415JS

Carbon Steel and 410 Stainless Steel Screws
The tensile strength of the substrate that is used in the chart below is typical for metal building and roofing applications.
Contact TFC if other substrate tensile strengths are required.
PULLOUT | ULTIMATE LOAD IN POUNDS
Fastener Grade 80 and Grade 50 Steel per ASTM A792/A1011/A653/A572/A529
Calculated Values In Accordance to AISI S100 | Section E4
Information
Grade 80
82Ksi Grade 50
Nom Min. 65Ksi Min. Steel
Thread and Dia. 26 Ga. 24 Ga. 22 Ga. 20 Ga. 18 Ga. 16 Ga. 14 Ga. 12 Ga. 1/8" 10 ga 1/4" 3/8" 1/2"
Point Type (in.) (.018") (.024") (.030") (.036") (.048") (.060") (.075") (.105") (.125") (.135") (.250") (.375") (.500")
#8-18 .164" 156 218 272 326 435 543
#10-16 .190" 180 252 315 378 504 627 786 1,101 1,311
#10-24 .190" 180 252 315 378 504 627 786 1,101 1,311
#12-14 .216" 205 286 358 430 573 716 895 1,253 1,492 1,611
#12-24 .216" 1,492 1,611 2,984 *4,475 *5,967
1/4-14 .250" 237 332 414 497 633 829 1,036 1,450 1,727 1,865 3,453
1/4-20 .250" 1,727 1,865 3,453 *5,180 *6,906
5/16-12 .3125" 829 1,036 1,295 1,813 2,158 2,331

* Denotes load exceeds tensile strength of screw.

For allowable loads, please apply an appropriate Factor of Safety as required
by local and national code requirements.

AISI S100 Section E4 recommends a Factor of Safety of 3 for allowable loads

DISCLAIMER: All test results and specifications are a result of laboratory tests. Appropriate
safety factors should be used by the user or specifier. Determining the proper fastener is the
responsibility of the user or specifier. Since application conditions vary and are uncontrollable
by TFC, we assume no liability for the use of this information.

TRIANGLE FASTENER CORPORATION PAGE 9 800.486.1832 | www.trianglefastener.com

MD 19
Visit our website for the most up-to-date product and technical information!
 ®
TECHNICAL DATA

F
Pullout In Steel - Average Ultimate in Pounds
Fastener PULLOUT | ULTIMATE LOAD IN POUNDS
Information Grade 80 and Grade 50 Steel per ASTM A792/A1011/A653/A572/A529
Calculated Values In Accordance to AISI S100 | Section E4
(Drill Points)
Grade 80
62Ksi Grade 50
Nom Min. 65Ksi Min. Steel
Thread Dia. 26 Ga. 25 Ga. 24 Ga. 22 Ga. 20 Ga. 18 Ga. 16 Ga. 14 Ga. 12 Ga. 1/8" 10 ga 1/4" 3/8" 1/2"
Type (in.) (.018") (.021") (.024") (.030") (.036") (.048") (.060") (.075") (.105") (.125") (.135") (.250") (.375") (.500") Pullover
#10-16 .190" 180 220 251 315 378 504 630 787 1102 1312 Tee Clip 24 ga. Zee Clip 24 ga.
Screw
#10-24 .190" 787 1102 1312 (Ave. Ultimate) (Ave. Ultimate)
#10 DP3 415 lbs. 510 lbs.
#12-14 .216" 205 251 286 358 430 573 716 895 1253 1492 1611
#12 GP 430 lbs. 692 lbs.
#12-24 .216" 1492 1611 2984 *4475 *5967
#14 DP1 407 lbs. 677 lbs.
#14-13 .235" 223 273 312 390 467 623 779 974
* Berridge Clips
REV.JES082712
1/4-14 .250" 829 1036 1450 1727 1865 3453 *5180 *6906
Tested values are available upon request. NOTE: * exceeds tensile strength of the screw.
Revised: 1110615JS Performance Specifications
Minimum Ultimate
Fastener Diameter Thread Tensile Shear Torsional
Pullout In Wood - Average Ultimate in Pounds F & Material Diameter (lbs.) (lbs.) (lbs-in)
#10-9 / Carbon 0.200” 1,520 1,150 60
Wood Type
#10-9 / 410SS 0.200” 2,500 1,625 85
Fastener 1/2” 5/8” 3/4” 7/16” 19/32” 23/32” 2x4
Dia. & Point Ply Ply Ply OSB OSB OSB SYP #10-13 / Carbon 0.195” 1,725 1,125 60
#10-13 GP 375 505 654 166 357 442 737 #10-13 / 302SS 0.195” 1,040 701 45
#10-9 GP 383 395 574 136 256 514 813 #10-16 / Carbon 0.186” 2,100 1,400 61
Decking fasteners
#12-11 GP 418 455 624 *164 379 573 918 #10-16 / 410SS 0.186” 3,200 2,130 92
tested with full thread
#14-13 DP1 434 475 626 153 327 457 991 embedment. 2 x 4 SYP #12-11 / Carbon 0.220" 2,500 2,000 95
Farabaugh Engineering Test: Project No. T279-10 & * T282-15 with 1” embedment #12-14 / Carbon 0.212” 2,778 2,000 100
REV JS110615
#12-14 / 302SS 0.212” 2,630 1,978 85
#12-24 / Carbon 0.213” 3,450 2,420 110
1/4-14 / Carbon 0.243” 3,850 2,600 150
Fastener Properties REV JS110615
#14-13 / Carbon 0.235” 3,620 2,500 115
Thread Type Thread Head Head
and Point Major Dia. Material Dia. Thickness Drive Finish
Salt Spray
#10-16 DP2 .180” C1022 .435” .080” #2 Sq .0003” Zinc & Yellow
The chart below provides general information with regard to corrosion
#10-24 DP3 .185” C1022 .435” .080” #2 Sq .0003” Zinc & Yellow
resistance of various plating and coatings. Contact TFC for detailed
™
#10-13 GP .190”
C1022
.450” .080” #2 Sq
TRI-SEAL Coated information.
302 SS Passivated SALT SPRAY Per ASTM F1941 & B117 (0% red rust) Rev. 120313
C1022 .0003” Zinc & Yellow Carbon steel and 410 stainless steel materials
#10-16 DP3 .180” .450” .080” #2 Sq
410 SS .0002" Zinc & Clear
™ Coating Salt Spray
C1022 TRI-SEAL Coated
#10-9 GP (ULP) .200”
410 SS
.435” .040” #2 Sq
Passivated .00015” min. (3 um) zinc plating with clear chromate 15hrs
C1022
™
TRI-SEAL Coated
.0002” min. (6um) zinc plating with clear chromate 24hrs
#12-11 GP .220” .450” .080” #2 Sq Passivated 410 Stainless Steel 48hrs
302 SS Passivated
#12-14 DP3 C1022 .450” .080” #2 Sq .0003” min. (8 um) zinc plating with clear chromate 48hrs
.210” .0003” Zinc & Yellow
(SD300) 304 SS .500” .090” T-30 Torx .0003” min. (8 um) zinc plating with yellow di-chromate 120hrs
.0003” Zinc & Yellow
#12-24 DP5 .210” C1022 .425” .110” #3 Sq ™
TRI-SEAL Coated
.0005” min. (12 um) zinc plating with clear chromate 72hrs
#14-13 DP1 .235” C1022 .500” .090” #2 Sq
.0003” Zinc & Yellow
™
.0007” min. (14 um) mechanical zinc with clear chromate 72hrs
TRI-SEAL Coated
1/4-14 DP3 (1") .500” .080” #2 Sq .0003” Zinc & Yellow
Epoxy (E-Coat) (ACQ Compatible) 100hrs
.245” C1022 ™ TRI-SEAL™ Long-life coating 1,000hrs
(2", 3", 4", 5", 6") .625" .100" #3 Sq TRI-SEAL Coated
Passivated 302 & 304 SS 1,000 hrs

Tooling | Do not use impact tools! Fastening Tips

Screw-gun RPM • A minimum of 3 factors of safety should be used for most self-drilling or self-tapping
Carbon Steel & 410SS Screws: 2,500 RPM Max. fasteners in metal | 5-6 for wood. Consult a design professional for appropriate values.
DP5, 1/4" & 5/16" DP3: 2,000 RPM Max. • Install fastener perpendicular to the work surface and tighten to no more than
302 & 304 Stainless Steel Tapping Screws: 1,000 RPM approximately 70% of the torsional strength.
Max.
For optimal performance, use screw-guns with torque • Allow at least three full threads to extend beyond the material. For wood applications,
control feature. allow 1” minimum embedment or full thread embedment in plywood and OSB for optimal
DO NOT OVER-TORQUE FASTENERS. pullout resistance.

Fastener Material Selection Based on the Galvanic Series of Metals

FASTENER MATERIAL
STEEL STAINLESS STEEL STAINLESS STEEL
Zinc Plated Type 410 Type 302, 304, 316 ALUMINUM
Key
Zinc | Galvanized | ZN/Al
A C C B A. The corrosion of the base metal is not increased by the fastener.
BASE METAL

Coated Steel
B. The corrosion of the base metal is slightly increased by the fastener.
Aluminum A 1Not Recommended B A C. The corrosion of the base metal may be considerably increased by the fastener material.
Steel / Cast Iron A,D C B A D. The plating on the fastener is rapidly consumed.
Brass, Copper, Bronze A,D,E A B A,E E. The corrosion of the fastener is increased by the base metal.
Stainless Steel
A,D,E A A A,E
300 Series

DISCLAIMER: All data and specifications are based on laboratory tests. Appropriate safety factors should be used by the user or specifier. Determining the proper
fastener is the responsibility of the user or specifier. Because application conditions vary, we assume no liability for the use of this information.

TRIANGLE FASTENER CORPORATION PAGE 10 800.486.1832 | www.trianglefastener.com

MD 28
Visit our website for the most up-to-date product and technical information!
PANEL-TITE TECHNICAL DATA SHEET
R

METAL-TO-WOOD SCREWS
Sizes
#10-14 Dual Thread #12-8 Low Root #12-11 Double Lead #14-10 Single Lead
with Type 17 Point with Type 17 Point Lap Type 17 Point

Material Specifications
Material: Carbon Steel Paint
Finish: TRI-SEAL Long-life (ACQ Compatible) Kalida-Kote Polyurethane with UV stabilizer

Material: 304 Stainless Steel

Finish: Passivated. (ACQ Compatible)

Material: 304 Stainless Steel Bi-Metal

Plating: Zinc Plated

Performance Specifications
Strengths (Carbon Steel)

Tensile Shear Torsional Pullover Strength in Pounds

Size (lbs. min) (avg. lbs. ult.) (min. in. lbs.)
#9-15 1,800 1,200 50 Washer 26ga 24ga 22ga 20ga 18ga
Size (.19") (.023") (.031") (.035") (.049")
#10-9 1,850 1,216 65
1/2" O.D. 515 674 875 1100 1627
#10-12 2,100 1,400 65
9/16" O.D. 587 744 915 993 1246
#10-14 1,850 1,216 65
15mm O.D. 564 810 1097 1166 1643
#12-8 2,183 1,946 80
#12-11 2,778 2,000 92
#14-10 3,150 2,150 125

Pullout Values in Wood (Carbon Steel or Stainless Steel) Corrosion Test Results
Ultimate Average Load in Pounds Force TRI-SEAL COATING
Wood Type
Fastener 5/8” 3/4” 7/16” 19/32” 23/32” 2 x 4 Testing Method *Results
1/2”
Dia. & Point Ply Ply Ply OSB OSB OSB SYP 20 Cycles
SO2 Test Per ASTM G87
#9-15 GP 350 402 548 173 344 431 887 (2 liters)
#10-9 Type 17 383 395 574 136 256 514 813 1,000
Salt Spray Per ASTM B117
hours
#10-13 GP 375 505 654 166 357 442 737
*0% Red Rust
#10-14 High-Low 375 505 654 166 357 442 737
#12-8 Type 17 296 445 552 139 445 538 748
D I S C L A I M E R : A L L T E S T R E S U LT S A N D FA S T E N E R
#14-10 434 475 626 153 327 475 1030 RECOMMENDATIONS ARE BASED ON LABORATORY CONDITIONS.
Rev JC022712 BECAUSE ACTUAL JOB SITE CONDITIONS VARY AND ARE
Test Setup: 2 x 4 - 1" embedment. All other
Report #T279-10 / Farabaugh Engineering and Testing / 9.30.2010 tests full thread embedment. UNCONTROLLABLE BY TFC. WE ASSUME NO LIABILITY FOR THE
USE OF THIS INFORMATION.

TRIANGLE FASTENER CORPORATION PAGE 11 800.486.1832 | www.trianglefastener.com

MD 37
Visit our website for the most up-to-date product and technical information!
 R
Bolt Strengths
C
Grade Identification Markings for Carbon Steel Externally Threaded Fasteners
Grade Identification Specification Material Nominal Proof Load Tensile Strength Hardness See
Marking Size in. Stress ksi Min ksi Rockwell Note
Min Max
SAE J429 - Grade 1 Low or Medium Carbon Steel 1/4 thru 1 1/2 33 60 B7O B100
SAE J429 - Grade 2 1/4 thru 3/4 over 55 74 B80 B100
over 3/4 thru 1 1/2 33 60 B70 B100
ASTM A307 - Grade A 1/4 thru 4 – 60 B69 B100
ASTM A307 - Grade B 1/4 thru 4 – 60 Min B69 B95
No Mark
– 100 Max
SAE J429 - Grade 5 Medium Carbon Steel, 1/4 thru 1 over 85 120 C25 C34
ASTM A449 - Type 1 Quenched and Tempered 1 thru 1 1/2 74 105 C19 C30
ASTM A449 - Type 1 over 1 1/2 thru 3 55 90 183 235 3

Low or Medium Carbon Steel,

SAE J429 - Grade 5.1 Quenched and Tempered N0.6 Thru 1/2 85 120 C25 C40 4

SAE J429 - Grade 5.2 Low Carbon Martensite Steel, C26 C36
ASTM A449 - Type2 Quenched and Tempered 1/4 thru 1 85 120 C25 C34

A325
ASTM A325 - Type 1 Medium Carbon Steel 5
Quenched and Tempered

ASTM A325 - Type 2 Low Carbon Martensite 1/2 Thru 1 85 120 C24 C35
A325
Steel, Quenched and Tempered over 1 to 1 1/2 74 105 C19 C31


Atmospheric Corrosion Resistant
A325
ASTM A325 - Type 3 Steel, Quenched and Tempered 6

Medium Carbon Alloy Steel, 1/4 thru 2 1/2 105 125 C26 C36
BC
ASTM A354 - Grade BC Quenched and Tempered over 2 1/2 thru 4 95 115 C22 C33

SAE J429 - Grade 8 Medium Carbon Alloy Steel, 1/4 thru 1 1/2 120 150 C33 C39
ASTM A354 - Grade BD Quenched and Tempered 1/4 thru 2 1/2 over 120 150 C33 C39
2 1/2 thru 4 105 140 C31 C39 7

Low Carbon Martensite Alloy

SAE J429 - Grade 8.2 Steel, Quenched and Tempered 1/4 thru 1 120 150 C33 C39

A490
ASTM A490 - Type 1 Medium Carbon Alloy Steel, 150 Min
Quenched and Tempered 1/2 Thru 11/2 120 170 Max C33 C38

A490
ASTM A490 - Type 2 Low Carbon Martensite Steel, 1/2 Thru 1 120 150 Min C33 C38
Quenched and Tempered 170 Max

A490
ASTM A490 - Type 3 Atmospheric Corrosion Resistant 150 Min
Steel, Quenched and Tempered 1/2 Thru 1 120 170 Max C33 C38 6

1. In addition to the indicated grade marking, all grades included in this Table must be marked for manufacturer identification.
2. While hex heads are shown, grade markings apply equally to products with other head configurations.
3. Hardnesses are Brinell Hardness Numbers.
NOTES: 4. Grade 5.1 is a popular grade for sems
5. A325 Type 1 bolts may also be marked with 3 radial lines 1200 apart in addition to the A325 marking.
6. The bolt manufacturer, at his option, may add other markings to indicate the use of atmospheric corrosion resistant steel.
7. A354 Grade BD products, in sizes 11/2 in. and smaller, are identified as shown and, at the manufacturers option, may have the letters BD added.
Larger sizes are marked only BD.

TRIANGLE FASTENER CORPORATION PAGE 12 800.486.1832 | www.trianglefastener.com

MD 246
Visit our website for the most up-to-date product and technical information!
 Carbon Steel Bolts
R

C
Proof and Tensile Strengths

Proof Load and Tensile

Strength Requirements (a)

Nominal Dia Stress Grade 1 Grade 2 Grade 4 Grades 5 and 5.2B Grade 5.1 Grade 7 Grades 8, 8.1,8.2B
of Product Area, Proof Tensile Proof Tensile Proof Tensile Proof Tensile Proof Tensile Proof Tensile Proof Tensile
and Threads in.2 Load, Strength Load, Strength Load, Strength Load, Strength Load, Strength Load, Strength Load, Strength
per in. lb Mm, lb lb Mm, lb lb Mm, lb lb Mm, lb lb Mm, lb lb Mm, lb lb Mm, lb

Coarse Thread Series - UNC

No. 6-32 0.00909 - - - - - - 750 1,100 - - - -
8-32 0.0140 - - - - - - 1,200 1,700 - - - -
10-24 0.0175 - - - - 1,500 2,100 - - - -
12-24 0.0242 - - - - - - 2,050 2,900 - - - -

1/4-20 0.0318
1,050 1,900 1.750 2,350 2,050 3,650 2,700 3,800 2,700 3,800 3,350 4,250 3,800 4,750

5/16-18 0.0524
1,750 3,150 2,900 3,900 3,400 6,000 4,450 6,300 4,450 6,300 5,500 6,950 6,300 7,850

3/8-16 0.0775
2,550 4,650 4,250 5,750 5,050 8,400 6,600 9,300 6,600 9,300 8,150 10,300 9,300 11,600

7/16-14 0.1063 3,500 6,400 5,850 7,850 6,900 12,200 9,050 12,800 9,050 12,800 11,200 14,100 12,800 15,900
1/2-13 0.1419 4,700 8,500 7,800 10,500 9,200 16,300 12,100 17,000 12,100 17,000 14,900 18,900 17,000 21,300

9/16-12 0.182 6,000 10,900 10,000 13,500 11,800 20,900 15,500 21,800 15,500 21,800 19,100 24,200 21,800 27,300
5/8-11 0.226 7,450 13,600 12,400 16,700 14,700 25,400 19,200 27,100 19,200 27,100 23,700 30,100 27,100 33,900
3/4-10 0.334 11,000 20,000 18,400 24,700 21,700 38,400 28,400 40,100 - - 35,100 44,400 40,100 50,100
7/8-9 0.462 15,200 27,700 15,200 27,700 30,000 53,100 39,300 55,400 - - 48,500 61,400 55,400 69,300
1-8 0.606 20,000 36,400 20,000 36,400 39,400 69,700 51,500 72,700 - - 63,800 80,600 72,700 90,900

1-1/8-7 0.763 25,200 45,800 25,200 45,800 49,600 87,700 56,500 80,100 - - 80,100 101,500 91,600 114,400

1-1/4-7 0.969 32,000 58,100 32,000 58,100 63,000 111,400 71,700 101,700 - - 101,700 127,700 116,300 145,400

1-3/8-6 1.155 38,100 69,300 38,100 69,300 75,100 132,800 85,500 121,300 - - 121,300 153,600 138,600 173,200

1-1/2-6 1.405 46,400 84,300 46,400 84,300 91,300 161,600 104,000 147,500 - - 147,500 186,900 168,600 210,800

Fine Thread Series - UNF

No. 6-40 0.01015 - - - - - - - - 850 1,200 - - - -
8-38 0.01474 - - - - - - - - 1,250 1,750 - - - -
10-32 0.0200 - - - - - - - - 1,700 2,400 - - - -
12-28 0.0258 - - - - - - - - 2,200 3,100 - - - -

1/4-28 0.0364
1,200 2,200 2,000 2,700 2,350 4,200 3,100 4,350 3,100 4,350 3,800 4,850 4,350 5,450

5/16-24 0.0580
1,900 3,500 3,200 4,300 3,750 6,700 4,900 6,950 4,900 6,950 6,100 7,700 6,950 8,700
3/8-24 0.0878 2,900 5,250 4,800 6,500 5,700 10,100 7,450 10,500 7,450 10,500 9,200 11,700 10,500 13,200

7/16-20 0.1187 3,900 7,100 6,550 8,800 7,700 13,650 10,100 14,200 10,100 14,200 12,500 15,800 14,200 17,800
1/2-20 0.1599 5,300 9,600 8,800 11,800 10,400 18,400 13,600 19,200 13,600 19,200 16,800 21,300 19,200 24,000

9/16-18 0.203 6,700 12,200 11,200 15,000 13,200 23,300 17,300 24,400 17,300 24,400 21,300 27,000 24,400 30,400
5/8-18 0.256 8,450 15,400 14,100 18,900 16,600 29,400 21,800 30,700 21,800 30,700 26,900 34,000 30,700 38,400
3/4-16 0.373 12,300 22,400 20,500 27,600 24,200 42,900 31,700 44,800 - - 39,200 49,600 44,800 56,000
7/8-14 0.509 16,800 30,500 16,800 30,500 33,100 58,500 43,300 61,100 - - 53,400 67,700 61,100 76,400
1 -12 0.663 21,900 39,800 21,900 39,800 43,100 76,200 56,400 79,600 - - 69,600 88,200 79,600 99,400
1-1/4 uns 0.679 22,400 40,700 22,400 40,700 44,100 78,100 57,700 81,500 - - 71,300 90,300 81,500 101,900
1-1/8-12 0.856 28,200 51,400 28,200 51,400 55,600 98,400 83,300 89,900 - - 89,900 113,800 102,700 128,400
1-1/4-12 1.073 35,400 64,400 35,400 64,400 69,700 123,400 79,400 112,700 - - 112,700 142,700 128,800 161,000
1-3/8-12 1.315 43,400 78,900 43,400 78,900 85,500 151,200 97,300 138,100 - - 138,100 174,900 157,800 197,200

1-1/2-12 1.581 52,200 94,900 52,200 94,900 102,800 181,800 117,000 116,000 - - 166,000 210,300 189,700 237,200

A) Proof loads and tensile strengths are computed by multiplying the proof load stresses and tensile strength stresses given in Table 1 by the stress
area of the thread.
0.9743
The stress area of sizes and thread series not included in this table may be computed from the formula: As = 0.7854 [D- n ]2 where D equals
nominal diameter in inch, and n equals threads per inch.

B) Grades 5.2 and 8.2 applicable to sizes 1/4 through 1 in.

TRIANGLE FASTENER CORPORATION PAGE 13 800.486.1832 | www.trianglefastener.com

MD 247
Visit our website for the most up-to-date product and technical information!
 R
Stainless Steel Bolts & NUTs
C Proof and Tensile Strengths

Mechanical requirements for stainless

steel bolts, screws, studs and nuts

Mechanical Requirements
Bolts1 Screws And Studs
Full Size Bolts, Machined Test Specimens Of Nuts
Screws, Studs Bolts, Screws, Studs
Yield2 Tensile Yield2 Tensile Hardness Proof Load Hardness
General Strength Strength Strength Strength Elongation3 Rockwell Stress Rockwell
Grade1 Description min ksi min ksi min ksi min ksi % Min Min ksi Min
Austenitic
303-A Stainless Steel 30 75 30 75 20 B75 75 B75
Sot. Annealed
Austenitic
304-A Stainless Steel 30 75 30 75 20 B75 75 B75
Sol. Annealed
Austenitic
304 Stainless Steel 50 90 45 85 20 B85 90 B85
Cold Worked
305-A Stainless Steel 30 75 20 75 20 B70 75 B70
Sol. Annealed
Austenitic
305 Stainless Steel 50 90 45 85 20 B85 90 B85
Cold Worked
Austenitic
316-A Stainless Steel 30 75 30 75 20 B70 75 B70
Sol. Annealed
Austenitic
316 Stainless steel 50 90 45 85 20 B85 90 B85
Sol. Annealed
Austenitic
316-SH Stainless Steel See See See See 15 C25 See C20
Strain Hardened Note 6 Note 6 Note 6 Note 6 Note 6
410-H Stainless Steel 95 125 95 125 20 C22 125 C22
Hardened and Tempered
410-HT Martensitic Stainless Steel 135 180 135 180 12 C36 180 C36
Hardened and Tempered
416-H Martensitic Stainless Steel 95 125 95 125 20 C22 125 C22
Hardened and Tempered
416-HT Martensitic Stainless Steel 135 180 135 180 12 C36 150 C36
Hardened and Tempered
430 Ferritic Stainless Steel 40 70 40 70 20 B75 70 B75

TRIANGLE FASTENER CORPORATION PAGE 14 800.486.1832 | www.trianglefastener.com

MD 248
Visit our website for the most up-to-date product and technical information!
 R
Carbon Steel Nuts
C Proof loads and hardness

Grade Identification Markings for

Popular Grades of Carbon Steel Nuts

Grade Identification Specification Material Nominal Proof Load Hardness See

Marking Size in. Stress ksi Rockwell Note
Min Max
ASTM A 563 - Grade 0 Carbon Steel 1/4 thru 1 1/2 69 B55 C32 3, 4
No Mark
ASTM A 563 - Grade A Carbon Steel 1/4 thru 1 1/2 90 B68 C32 3, 4
ASTM A 563 - Grade B Carbon Steel 1/4 thru 1 120 B55 C32 3, 4
over 1 thru 1 1/2 105

ASTM A563 - Grade C Carbon Steel, May Be Quenched and Tempered 1/4 thru 4 144 B78 C38 5

3
ASTM A563 - Grade C3 Atmospheric Corrosion Resistant Steel.May Be Quenched and Tempered 1/4 thru 4 144 B78 C38 5.9

ASTM A563 - Grade D Carbon Steel, May Be Quenched and Tempered 1/4 thru 4 150 B84 C38 6

DH
ASTM A563 - Grade DH Carbon Steel, Quenched and Tempered 1/4 thru 4 175 C24 C38 6

3
DH
ASTM A563 - Grade DH3 Atmospheric Corrosion Resistant Steel, Quenched and Tempered 1/4 thru 4 175 C24 C38 5, 9

1
ASTM A194 - Grade 1 Carbon Steel 1/4 thru 4 130 B70 - 7

2
ASTM A194 - Grade 2 Medium Carbon Steel 1/4 thru 4 150 159 352 78

2 H
ASTM A194 - Grade 2H Medium Carbon Steel, Quenched and Tempered 1/4 thru 4 175 C24 C38 7

2 HM
ASTM A194 - Grade 2HM Medium Carbon Steel, Quenched and Tempered 1/4 thru 4 150 159 237 7, 8

4
ASTM A194 - Grade 4 Medium Carbon Alloy Steel, Quenched and Tempered 1/4 thru 4 175 C24 C38 7

7
ASTM A194 - Grade 7 Medium Carbon Alloy Steel, Quenched and Tempered 1/4 thru 4 175 C24 C38 7

7M
ASTM A194 - Grade 4 Medium Carbon Alloy Steel, Quenched and Tempered 1/4 thru 4 150 159 237 7

See note 1,2,10

NOTES:
1. In addition to the indicated grade marking, all grades, except AS63 grades 0, A and B, must be marked for manufacturer identification.
2. The markings shown for all grades of A194 nuts are for cold formed and hot forged nuts. When nuts are machined from bar stock the nut must be additionally marked with the letter 'B'.
3. Nuts are not required to be marked unless specified by the purchaser. When marked, the identification marking shall be the grade letter 0, A or B.
4. Properties shown are those of non-plated or non-coated coarse thread hex nuts.
5. Properties shown are those of coarse thread heavy hex nuts.
6. Properties shown are those of coarse thread heavy hex nuts.
7. Properties shown are those of coarse and 8-pitch thread heavy hex nuts.
8. Hardnesses are Brinell Hardness Numbers.
9. The nut manufacturer; at his option, may add other markings to indicate the use of atmospheric corrosion resistant steel.
10. Specifications - ASTM A563 - Carbon and Alloy Steel Nuts / ASTM A194 - Carbon and Alloy Steel Nuts for Bolts for High Pressure and High Temperature Service

TRIANGLE FASTENER CORPORATION PAGE 15 800.486.1832 | www.trianglefastener.com

MD 249
Visit our website for the most up-to-date product and technical information!
 ®
FAB-LOK MAINTAINS PANEL INTEGRITY IN
HIGH-STRESS ENVIRONMENTS
FAB-LOK® fasteners were designed to maintain panel
integrity in high-stress environments such as: high wind areas,
expansion and contraction, severe vibration, racking and the
repair of oversized holes.

Sizes
Penetrating Wt.
Material Size Length Grip Range /M
FAS 10-4 1.373” .062”-.250” 23
Carbon Steel FAS 10-8 1.612” .250”-.500” 24
FAS10-12 1.807” .500”-.750” 28
FAC10-4 1.373” .062”-.250” 23
H-3 (300 series)
Stainless Steel
FAC 10-8 1.612” .250”-.500” 24 Vibration, either from inside or outside a
FAC 10-12 1.807” .500”-.750” 28 building, can make ordinary fasteners loosen
and back out.

FAB-LOK® fasteners combine a slotted

WEATH-R-SEAL Washers aluminum sleeve and fastener to provide the
simplicity and strength of both elements.
Part Description

Aluminum Bonded .729” O.D. - .040 Aluminum

Weath-R-Seal Washers
Installation Holding Sleeve
1” O.D. - .040” Aluminum
1. Predrill with a 5/16" diameter drill bit p.n. : EZL900
.729” O.D. 20 gauge 304 2. Insert FABLOK into hole. Use the FABLOK
304 Stainless Steel Bonded S/S
Weath-R-Seal Washers holding sleeve with a DEWALT screw-gun
1” O.D. 20 gauge 304 S/S (DW268 or DW267)

Technical Information Clamping Force

Pull-out tests were performed on a Model L Dillon Dynamometer. FAB-LOK® TypeFAS

FAB-LOK® fasteners were installed in single sheet and two sheets Maximum 900 lbs.
of metal and pulled over the tines of the FAB-LOK® to determined Residual 860 lbs.
holding values.

Single Shear Strength

Comparison: FAB-LOK® & Sheet Metal SC
FAB-LOK®Type FAC FAS
FAB-LOK® #14 Sheet Avg. shear 1885 lbs. 2400 lbs.
Sheet Material FAS-10-4 Metal Screw
Strip test in .032” Aluminum 75 inch-lbs.* 65 inch-lbs.*
Strip test in 26 ga. Steel 75 inch-lbs.* 45 inch-lbs.* Hydrostatic Test
Strip test in 24 ga. Steel 75 inch-lbs.* 55 inch-lbs.* FAB-LOK® H20 Length
Type Pressure of test Result
FAC - 10-4 100 psi 5 days No leaks
Type Fac - Single Sheet
Sheet Sheet Failure Type of Fatigue Tests
Material Thickness lbs.* Failure
Two thicknesses of 26 gauge metal fastened with FAB-LOK® and tested
24 ga. 833 Sheet Split on 5000 lb. capacity machine at 1500 cycles per minute, sustained
20 ga. 858 Sheet Split 1,775,500 cycles when failure of sheets occurred. Fastener did not fail.
Steel 18 ga. 1050 Sheet Split
FAB-LOK® fastening 1/8” aluminum plate to 3/16” steel of a railroad
16 ga. 1293 Sheet Split
freight car, held without failure when the car was subjected to jarring
14 ga. 1400 Fastener Broke vibration by a Hewitt-Robins Car Shaker at 900 cycles for ten minutes.

INFORMATION PROVIDED HERE IS BASED UPON TESTS BELIEVED TO BE RELIABLE. IN AS MUCH AS ELCO FASTENING SYSTEMS HAS NO CONTROL OVER THE
EXACT MANNER IN WHICH OTHERS MAY USE THIS INFORMATION, IT DOES NOT GUARANTEE THE RESULTS TO BE OBTAINED NOR DOES THE COMPANY MAKE
ANY EXPRESS OR IMPLIED WARRANTY OF MERCHANTABILITY, OR FITNESS FOR A PARTICULAR PURPOSE CONCERNING THE EFFECTS OR RESULTS
OF SUCH USE.

TRIANGLE FASTENER CORPORATION PAGE 16 800.486.1832 | www.trianglefastener.com

MD 48
Visit our website for the most up-to-date product and technical information!
 R
Corrosion Information
C
Interacting Influences occurs more quickly in industrial plants where heat is inherent in the
process as opposed to industries which conduct their operations at
This brief look at the rusting of steel points up the interacting influences
ambient temperatures or in the luxury of an air conditioned atmosphere.
which initiate, and control, the mechanism of electrochemical corrosion.
Galvanic Corrosion
First, there must be the possibility for any electrical current to flow.
This means either the contacting of dissimilar metals with different Similar metals are compatible; dissimilar metals are not. When dissimilar
electropotentials, or some measure of heterogeneity in the same metals contact in the presence of an electrolyte, a galvanic action occurs
base metal. The greater the differential, the stronger the current flow which causes one of the metals to corrode at a much faster than normal
and the faster and more severe the corrosive action. Corrosion of rate, while the other corrodes more slowly, if at all. The rate, location and
the same metal, for example; the rusting of steel, normally results in extent of the corrosion depends on three factors:
a uniform corroding of the entire exposed surface When dissimilar
• The difference in electrical potentials
metals contact, the attack is usually more localized.
• The conductivity strength of the corroding medium, and
Second, there must be an electrolyte a medium through which the
electrical current flows. Electrolytes occur naturally in our everyday • The relative sizes of the contacting areas.
environments - humidity, fog, dew, condensation, rain - and with a broad
All metals have electrical potentials. Through research, the potentials of
variation in their occurrence and intensity. For example, the corrosion
different base metals and their alloys, when exposed to sea water, were
survival expectancy of steel is shortened considerably when exposed in
measured and then ranked into a series. In an electrical couple, the metal
the high humidity Southern states as opposed to the ultra-dry desert
of higher electrical potential is the cathode (-), that of the lower the anode
climates of Nevada and Arizona. Similarly, structures and equipment
(+). Current flows from the cathode to the anode, from the anode through
survive longer in rural Midwestern states than in either ocean bordering
the electrolyte (corroding medium), and back to the cathode. Corrosion
states or in heavily industrialized areas with their high impurity
occurs at the point the current leaves the anode to enter the electrolyte.
atmospheres. Even in the home, storing articles in the dryness of an attic
When dissimilar metals contact, the anode corrodes, the cathode survives.
is more protective than in the dampness of a basement.
Galvanic Series
Distilled water is a poor conductor; tap water with its modest chemical
content is better; industrial exposures with their pollutants and Table 1 presents the Galvanic Series of Metals and Alloys. The various
contaminants are even better; and salt water is exceptionally good. metals are grouped. Those within the same group are reasonably
Whenever the electrolyte is agitated, such as flowing water, its conductivity compatible when used together; those from different groups cause a
is significantly magnified. The "dirtier" the electrolyte, the better its corrosion problem. Some metals, basically those with significant contents
conductivity, and the faster the rate of corrosion. of nickel and chromium, are included in the Series both in their active and
passive conditions. Passivation (surface cleaning and sealing) lowers the
Third, there must be oxygen. As most products of corrosion are oxides
metal's electrical potential and improves its corrosion behavior.
formed by the chemical reaction, the presence of oxygen is mandatory.
Without oxygen, most forms of corrosion would be stalemated. However, Study of the Galvanic Series suggests that steel and aluminum are
its complete elimination is an engineering impracticality. Oxygen is the reasonably compatible; but, if titanium and aluminum contact, the
principal element of the air we breathe, and it is present, although to a aluminum, as the anode, will corrode Fig. 2 illustrates another example A
lesser degree, underground and underwater copper plate is joined to an aluminum plate using a carbon steel bolt. If
none of the contacting surfaces are protected, corrosion will occur. The
The importance of oxygen can be illustrated by considering an oceangoing
bolt, where it touches the copper, will corrode severely. However, the bolt,
steel-hulled ship. Without suitable protection of its exposed surfaces, the
where it contacts the aluminum, will not corrode, because it is now the
entire hull would corrode, but at three different rates. The plates at the
cathode. The aluminum plate in contact with the bolt may corrode, but
water line would go first because of the concentrated aggressiveness of
only slightly because of the minor difference in their electropotentials and
the sea water coupled with unlimited oxygen. The upper structure and
the large anode-to-Cathode area ratio. The aluminum plate will corrode
decks would corrode more slowly because the electrolyte is now a spray
where its exposed exterior surfaces contact the copper plate The
which has lost some of its intensity although the oxygen supply is
aluminum plate may also corrode on its interior surface, but not to the
undiminished. The fully submerged bottom of the hull would survive the
same degree, because the corroding medium and oxygen supply are
longest simply because of the meagerness of the oxygen supply.
largely sealed out due to the bolt's clamping action.
Temperature, while not a direct contributor to corrosion, is definitely a
Galvanic Series of Metals and Alloys
Carbon Steel Bolt
Heavy Corrosion +Corroded End (anodic, or least noble)
Copper Plate
Magnesium, Magnesium alloys, Zinc
Aluminum 1100, Cadmium, Aluminum 2024-T4, Steel or Iron, Cast Iron, Chromium-
iron (active),
Ni-Resist cast iron
Type 304 Stainless (active), Type 316 Stainless (active)
Lead tin solders, Lead, Tin
Heavy Corrosion Aluminum Plate
Nickel (active), Inconel nickel-chromium alloy (active), Hastelloy Alloy c (active)
Modest Corrosion
Brasses, Copper, Bronzes, Copper-nickel alloys, Monel nickel-copper alloy
Silver solder, Nickel (passive), Inconel nickel-chromium alloy (passive)
Effects of Galvanic Corrosion
Chromium-iron (passive), Type 304 Stainless (passive),
Type 316 Stainless (passive), Hastelloy Alloy C (passive)
factor in the rate at which it occurs. Generally, heat accelerates chemical Silver, Titanium, Graphite, Gold, Platinum
reactions. All other conditions being equal, corrosion happens quicker and - Protected End (cathodic, or most noble)
more markedly in southern climates than in those of the north. It also

Taken from IFI Fastener Standards

TRIANGLE FASTENER CORPORATION PAGE 17 800.486.1832 | www.trianglefastener.com

MD 250
Visit our website for the most up-to-date product and technical information!
 R
Corrosion Information
C Galvanic Action
Galvanic Corrosion - compatible metals charts

To minimize galvanic corrosion, fasteners should be considered

based on their material compatibility with the substrates.

Determine the materials being fastened and choose a fastener

material that is close in proximity on the chart. The closer together
the material are on the chart the less galvanic action will occur.

Metals listed on the top of the chart (anotic) will corrode faster
than the metals on the bottom of the chart (cathodic).

Contact a corrosion specialist to determine the best material for

your application.

Fastener Material Selection Based on the Galvanic Series of Metals Revised by TFC: 0315JS
Table developed using information supplied by AISI Committee of Stainless Steel Producers.
Key
A. The corrosion of the base metal is not increased by the fastener.
B. The corrosion of the base metal is slightly increased by the fastener.
C. The corrosion of the base metal may be considerably increased by the fastener material.
D. The plating on the fastener is rapidly consumed.
E. The corrosion of the fastener is increased by the base metal.

FASTENER MATERIAL
STEEL STAINLESS STEEL STAINLESS STEEL
Zinc Plated Type 410 Type 302, 304, 316 ALUMINUM
Zinc | Galvanized | ZN/Al
A C C B
BASE METAL

Coated Steel
Aluminum A 1Not Recommended B A
Steel / Cast Iron A,D C B A
Brass, Copper, Bronze A,D,E A B A,E
Stainless Steel
A,D,E A A A,E
300 Series
Footnotes
1. Because aluminum can expand a large distance, the high hardness of 410 SS case harden screws may lead to screw to
failure due to lack of ductility or stress corrosion cracking.

NOTE: Organic coating to the screw will improve the corrosion resistance. Environments can affect the rate of corrosion
and change the activity of the metals.

Special Note: Preservative-Treated Lumber Applications

ACQ, Penta, CA or CBA preservative-treated lumber can be incompatible with certain types of fasteners. In those cases where any type
of metal roof or wall cladding materials are being attached to preservative treated lumber, the following fasteners are not compatible: zinc
plated screws, zinc-alloy headed screws, stainless capped screws, aluminum, copper and copper alloy. When attaching metal panels to
those types of preservative-treated lumber, a moisture barrier should be used between the lumber and the panel material. Metal panel
fasteners that are compatible with preservative-treated lumber are stainless steel fasteners, or hot dip galvanized nails manufactured
to ASTM A153 class D or heavier. Other types of fasteners coated with proprietary anti-corrosive technologies are also available for use
with preservative-treated lumber. In addition, zinc-plated screws can be used in CCA and MCQ pressure-treated lumber.
TRIANGLE FASTENER CORPORATION PAGE 18 800.486.1832 | www.trianglefastener.com
MD 252
Visit our website for the most up-to-date product and technical information!
 R
Corrosion Information
C Testing
General Corrosion Data for Fastener Finishes
There are two popular tests use on fasteners to compare their resistance to corrosion. These test are conduced using procedures that
allow a specifier to compare various finishes and materials in a controlled environment. The results do not relate to years of service.
Here is an explanation of the tests.

Salt Spray (ASTM B117)

This test is used to compare performance of various finishes in a
salt environment. This testing is conducted using a cabinet with a
controlled environment consisting of fog with 5% salt solution at 95
degrees F. The test runs continuously with the specimens being
visually judged every 24 hours for percent of total surface loss due
to red rust along with the number of hours that have accumulated
to that point.

Example of Salt Spray Test Cabinet

Kesternich (DIN 50018)

This test is used to compare performance of various finishes in an acidic environment. This
testing is conducted using a cabinet with a controlled environment consisting of an injection of
0.2 liters of SO2 gas, moisture to a relative humidity of 100% at a temperature of 400
Centigrade. This atmosphere is held for 8-hours, then the door of the cabinet is opened and
ambient air is allowed to circulate through the cabinet for 16 hours. This 24-hour period
comprises one full cycle. The test runs continuously with the specimens being visually judged
every 24 hours for percent of total surface loss due to red rust along with the number of cycles
that have accumulated to that point.

Example of
Kesternich Cabinet

CORROSION Protection INFORMATION

The following information was compiled from known data that compares various
finishes in a controlled environment. The material set forth herein is for general
information only and cannot be construed as a substitute for competent professional
advice or service. Any part considering application use of this information does
so at their own risk and assumes any and all liability from application or use.
Consult a corrosion specialist to determine the best fastener for your condition.

salt spray results

The chart provides general information with regard to corrosion resistance of
various plating and coatings. Contact TFC for detailed information.

SALT SPRAY Per ASTM F1941 & B117 (0% red rust) Rev. 042111

Carbon steel and 410 stainless steel materials

Coating Salt Spray
.00015” min. (3 um) zinc plating with clear chromate 15hrs
.0002” min. (6um) zinc plating with clear chromate 24hrs
Passivated 410 Stainless Steel 48hrs
.0003” min. (8 um) zinc plating with clear chromate 48hrs
.0003” min. (8 um) zinc plating with yellow di-chromate 120hrs
.0005” min. (12 um) zinc plating with clear chromate 72hrs
.0007” min. (14 um) mechanical zinc with clear chromate 72hrs
Epoxy (E-Coat) (ACQ Compatible) 100hrs
TRI-SEAL™ Long-life coating 1,000hrs

TRIANGLE FASTENER CORPORATION PAGE 19 800.486.1832 | www.trianglefastener.com

MD 251
Visit our website for the most up-to-date product and technical information!
 R
Corrosion Information
C PLATINGS & APPLICATIONS
Characteristics of Platings, Coatings and Finishes
Plating, Coating For Use On Degree of
or Finish Corrosion Resistance Characteristics
Rust inhibitors All metals Varies with type Oils, greases, etc. Vary in color and film thickness. Usually applied to black oxide finishes.
Used to protect parts in transit and temporary storage.

Zinc, electroplated All metals Very good Blue to blue-white gray color.

Cadmium, electroplated Most metals Excellent Bright silver-gray, dull gray, or black finish. Particularly effective corrosion
protection in marine applications. Used for decorative purposes. High lubricity.

Clear chromate finish Zinc and cadmium Very good to excellent Clear bright or iridescent chemical conversion coating applied to plated parts to enhance
plated parts corrosion protection, coloring, and paint bonding.

Dichromate Zinc and cadmium Very good to excellent Yellow, brown, green or iridescent colored coating same as clear chromate.
plated parts

Color chromate finish Zinc and cadmium Very good to excellent Olive drab, blue, gold, bronze, etc. Same as clear chromate.
plated parts

Zinc or Manganese Steel Good Black in color. Added protection when oiled with a non-drying petroleum oil containing
Phosphate corrosion inhibitors. Good lubricity.

Color phosphate coatings Steel Superior to regular phosphate Chemically produced color coating. Available in blue, green, red, purple, etc.
and oiled surfaces

Hot-dip zinc All metals Very good Gives maximum corrosion protection. Dull grayish color Necessitates thread size
adjustments to permit assembly.

Hot-dip aluminum Steel Very good Gives maximum corrosion protection. Dull grayish color. Necessitates thread size
adjustments to permit assemblably.

Mechanically deposited Zinc Steel Very good Dull gray, smooth finish. Corrosion protection depends on coating thickness.
Good coverage in recesses and thread roots.

Tin, electroplated All metals Silver-gray color. Excellent corrosion protection for parts in contact with food.

Hot-dip tin All metals Excellent Same as electroplated but thickness is harder to control.

Lead-tin Steel, usually Fair to good Silver-gray, dull coating. Applied by hot-dip method. Helps lubricity.

Silver, electroplated All metals Excellent Decorative, expensive, excellent electrical conductor.

Chromium, electroplated Most metals Good (improves with copper Bright, blue-white, lustrous finish. Has relatively hard surface.
and nickel undercoats) Used for decorative purposes or to add wear resistance.

Copper, electroplated Most metals Fair Used for nickel and chromium plate undercoat. Can be blackened and relieved to obtain
Antique, Statuary, and Venetian finishes.

Brass, electroplated, lacquered Steel, usually Fair Brass electroplated which is then lacquered.
Recommended only for indoor decorative use.

Bronze, electroplated, lacquered Steel, usually Fair Has color similar to 80% copper, 20% zinc alloy. Electroplated and then lacquered.
Recommended only for indoor decorative use.

Copper, brass, bronze, Most metals Indoor, very good Decorative finishes. Applied to copper, brass,and bronze plated parts to match colors.
miscellaneous finishes Color and tone vary from black to almost the original color. Finish names are: Antique,
Black Oxide, Statuary ,Old English, Venetian, Copper Oxidized.

Bright nickel Most metals Indoor excellent. Outdoor good Electroplated silver-colored finish. Used for appliances, hardware, etc.
if thickness at least 0.0005 in.

Dull nickel Most metals Same as bright nickel Whitish cast. Can be obtained by mechanical surface finishing or a special satin bath.

Lacquering, clear or All metals Improves corrosion resistance. Used for decorative finishes. Clear or colored to
color-matched Some types designed for humid match mating color or luster
or other severe applications

Anodizing Aluminum Excellent Acid electrolytic treatment. Frosty-etched appearance.

Hard oxide surface gives excellent protection.

Passivating Stainless steel Excellent Chemical treatment. Removes iron particles and produces a passive surface.

TRIANGLE FASTENER CORPORATION PAGE 20 800.486.1832 | www.trianglefastener.com

MD 253
Visit our website for the most up-to-date product and technical information!
 R
Stainless steel
C Technical Data
Stainless Steel Material
Stainless steels are alloys of iron that has a minimum of about 12% chromium. The chromium is the alloying element that imparts its corrosion resistant
qualities. It combines with oxygen to form a thin, invisible, non-reactive chromium oxide film on the surface. This self-forming, self-healing passive film
always forms in the presents of oxygen. When exposed to weather, a 12% chromium stainless steel (passive) will not corrode (red rust). If greater
corrosion protection is required, a stainless grade is used that has mores chromium.

300 Series stainless steels are chromium-nickel compositions and are known as austenitic. They offer excellent corrosion resistance, for the most part
are non-magnetic, and have excellent ductility. 300 series stainless steel can be cold work hardened and show slight magnetism, but it cannot be heat-
treated. Type 304 is one of the most popular for fasteners used in construction applications. This type, sometimes referred as 18-8 (18% chromium,
8% nickel), provides better thread strength than 302, helping eliminate thread rollover. Most fasteners that are made in 304 stainless are self-tapping
type due to the fact that they cannot be heat-treated. Self-drilling fasteners are available, but for steel applications must have a carbon steel drill tip
affixed to the body so drilling can occur like our SD300 brand.

400 Series stainless steels are straight-chromium compositions and are known as martensitic. They resist corrosion in mild environments, and can be
heat-treated for additional strength. They are magnetic, and when heat-treated, provide exceptional strength. The most popular grade used for
fasteners is 410 stainless. Because of its heat-treating capabilities, self-drilling fasteners are widely produced in this grade. Corrosion can occur rather
quickly if not properly process. It is recommended that fasteners that are used in exterior construction applications have some sort of plating on the
surface. This will not only aid improve corrosion resistance, but can provide lubricity for improving drilling and tapping.

Material Selection
Many variables characterize a corrosive environment, i.e., chemicals and their concentration, atmospheric conditions, temperature, time, so it is difficult
to select which alloy to use without knowing the exact nature of the environment. However, there are guidelines:

Type 304 serves a wide range of applications. It withstands ordinary rusting in architecture, it is resistant to food-processing environments (except
possibly for high-temperature conditions involving high acid and chloride contents), it resists organic chemicals, dyestuffs, and a wide variety of
inorganic chemicals. Type 304 L (low carbon) resists nitric acid well and sulfuric acids at moderate temperature and concentrations. It is used
extensively for storage of liquefied gases, equipment for use at cryogenic temperatures (304N), appliances and other consumer products, kitchen
equipment, hospital equipment, transportation, and wastewater treatment.

Type 316 contains slightly more nickel than Type 304, and 2-3% molybdenum giving it better resistance to corrosion than Type 304, especially in
chloride environments that tend to cause pitting. Type 316 was developed for use in sulfite pulp mills because it resists sulfuric acid compounds. Its
use has been broadened, however; to handling many chemicals in the process industries.

Type 430 has lower alloy content than Type 304 and is used for highly polished trim applications in mild atmospheres. It is also used in nitric acid and
food processing.

Type 410 has the lowest alloy content of the three general-purpose stainless steels and is selected for highly stressed parts needing the combination
of strength and corrosion resistance, such as fasteners. Type 410 resists corrosion in mild atmospheres, steam, and many mild chemical environments.

Service tests are most reliable in determining optimum material, and ASTM G-4 is a recommended practice for carrying out such tests. Tests should
cover conditions both during operation and shut-down. For instance, sulfuric, sulfurous and polythionic acid condensates formed in some processes
during shutdowns may be more corrosive than the process stream itself. Tests should be conducted under the worst operating conditions anticipated.

Specifications and recommended practices relating to stainless steels are also issued by ASTM. Stainless steels resist corrosion in a broad range of
conditions, but they are not immune to every environment. For example, stainless steels perform poorly in reducing environments, such as 50% sulfuric
and hydrochloric acids at elevated temperatures. The corrosive attack experienced is a breakdown of the protective film over the entire metal surface.

Such misapplications of stainless steels are rare and are usually avoided. The types of attack which are more likely to be of concern are pitting, crevice
attack, stress corrosion cracking, and intergranular corrosion.
Source: Design Guidelines for the selection and use of stainless steel. Specialty Steel Industry of the United States.

Relative Corrosion Resistance of AISI Stainless Steels

Atmospheric Chemical
TYPE UNS Mild Atmospheric
Number Number and Fresh Water Industrial Marine Mild Oxidizing Reducing

302 (S30200) X X X X X

304 (S30400) X X X X X

305 (530500) X X X X X

316 (531600) X X X X X X

410 (S41000) X X

430 (543000) X X X X

* The"X" notations indicate that a specific stainless steel type may be considered as resistant to the corrosive environment categories.

This list is suggested as a guideline only and does not suggest or imply a warranty on the pan of the Specialty Steel Industry of the United States or any of the member
companies. When selecting a stainless steel for any corrosive environment, it is always best to consult with a corrosion engineer and, if possible, conduct tests in the
environment involved under actual operating conditions.

TRIANGLE FASTENER CORPORATION PAGE 21 800.486.1832 | www.trianglefastener.com

MD 255
Visit our website for the most up-to-date product and technical information!
 R
Stainless steel
C Technical Data
Where Different Grades of Stainless Steel Are Used
Acids applicable for parts having temperatures above 120 F (50 C), for dilute
Hydrochloric acid: Stainless generally is not recommended except vapors and high pressures. Type 317 has somewhat greater corrosion
when solutions are very dilute and at room temperature. resistance than Type 316 under severely corrosive conditions. None of
the stainless steels has adequate corrosion resistance to glacial acetic
"Mixed acids": There is usually no appreciable attack on Type 304 or
acid at the boiling temperature or at superheated vapor temperatures.
316 as long as sufficient nitric acid is present.
Aldehydes: Type 304 is generally satisfactory.
Nitric acid: Type 304L or 430 is used.
Amines: Type 316 is usually preferred to Type 304.
Phosphoric acid: Type 304 is satisfactory for storing cold phosphoric
acid up to 85% and for handling concentrations up to 5% in some unit Cellulose acetate: Type 304 is satisfactory for low temperatures, but
processes of manufacture. Type 316 is more resistant and is generally Type 316 or Type 317 is needed for high temperatures.
used for storing and manufacture if the fluorine content is not too high.
Citric, formic and tartaric acids: Type 304 is generally acceptable at
Type 317 is somewhat more resistant than Type 316. At concentrations
moderate temperatures, - but Type 316 is resistant to all concentrations
up to 85%, the metal temperature should not exceed 212 F (100 C) with
at temperatures up to boiling.
Type 316 and slightly higher with Type 317. Oxidizing ions inhibit attack
and other inhibitors such as arsenic may be added. Esters: From the corrosion standpoint, esters are comparable with
organic acids.
Sulfuric acid: Type 304 can be used at room temperature for
concentrations over 80%. Type 316 can be used in contact with sulfuric Fatty acids: Up to about 300 F (150 C), Type 304 is resistant to fats and
acid up to 10% at temperatures up to 120 F (50 C) if the solutions are fatty acids, but Type 316 is needed at 300 to 500 F (150 to 260 C) and
aerated; the attack is greater in airfree solutions. Type 317 may be used Type 317 at higher temperatures.
at temperatures as high as 150 F (65 C) with up to 5% concentration.
The presence of other materials may markedly change the corrosion Paint vehicles: Type 316 may be needed if exact color and lack of
rate. As little as 500 to 2000 ppm of cupric ions make it possible to use contamination are important.
Type 304 in hot solutions of moderate concentration. Other additives Phthalic anhydride: Type 316 is usually used for reactors, fractionating
may have the opposite effect. columns, traps, baffles, caps and piping.
Sulfurous acid: Type 304 may be subject to pitting, particularly if some Soaps: Type 304 is used for parts such as spray towers, but Type 316
sulfuric acid is present. Type 316 is usable at moderate concentrations may be preferred for spray nozzles and flake-drying belts to minimize off
and temperatures. color product.
Bases Synthetic detergents: Type 316 is used for preheat, piping, pumps and
Ammonium hydroxide, sodium hydroxide, caustic solutions : Steels reactors in catalytic hydrogenation of fatty acids to give salts of
in the 300 series generally have good corrosion-resistance at virtually all sulfonated high molecular alcohols.
concentrations and temperatures in weak bases, such as ammonium
hydroxide. In stronger bases, such as sodium hydroxide, there may be Tall oil (pulp and paper industry): Type 304 has only limited usage in
some attack, cracking or etching in more concentrated solutions and at tall-oil distillation service. High-rosin-acid streams can be handled by
higher temperatures. Commercial purity caustic solutions may contain Type 316L with a minimum molybdenum content of 2.75%. Type 316 can
chlorides, which will accentuate any attack and may cause pitting of also be used in the more corrosive high-fatty-acid streams at
Type 316 as well Type 304. temperatures up to 475(245 C), but Type 317 will probably be required
at higher temperatures.
Organics
Acetic acid: Acetic acid is seldom pure in chemical plants but generally Tar: Tar distillation equipment is almost all Type 316 because coal tar
includes numerous and varied minor constituents. Type 304 is used for a has a high chloride content; Type 304 does not have adequate
wide variety of equipment including stills, base heaters, holding tanks, resistance to pitting.
heat exchangers, pipelines, valves and pumps for concentrations up to
Urea: Type 316L is generally required.
99% at temperatures up to about 120 F (50 C). Type 304 is also
satisfactory for contact with 100% acetic acid vapors, and-if small Pharmaceuticals : Type 316 is usually selected for all parts in contact
amounts of turbidity or color pickup can be tolerated for room with the product because of its inherent corrosion resistance and greater
temperature storage of glacial acetic acid. Types 316 and 317 have the assurance of product purity.
broadest range of usefulness, especially if formic acid is also present or
if solutions are unaerated. Type 316 is used for fractionating equipment,
for 30 to 99% concentrations where Type 304 cannot be used, for
storage vessels, pumps and process equipment handling glacial acetic
acid, which would be dis-colored by Type 304. Type 316 is likewise
Source: Design Guidelines for the selection and use of stainless steel. Specialty Steel Industry of the United States.

TRIANGLE FASTENER CORPORATION PAGE 22 800.486.1832 | www.trianglefastener.com

MD 256
Visit our website for the most up-to-date product and technical information!
 R
Fasteners for
C Treated lumber
“TFC SPECIFIC” FASTENERS FOR USE IN TREATED LUMBER
AND FIRE RATED LUMBER
Effective January 1, 2004, lumber treated with arsenic (CCA – Chromated Copper Arsenic) is no longer produced
for residential applications, and a new treated lumber material known as ACQ (Alkaline Copper Quanternary)
is being utilized.

From a fastener standpoint, it’s important to know that ACQ has up to six (6) times more copper content than
the wood it replaces. This condition can cause fasteners plated with electro-plated zinc to corrode at a very fast
rate, leaving the bare steel to red rust.

As recommended by the Southern Pine Council (SPC); recognized by the NRCA and the MCA; required by
the International Residential Code (R319.3) and the International Building Code (2304.9.5), the following
fasteners are acceptable for use in ACQ pressure treated lumber and fire rated lumber;
• Hot-dipped galvanized complying with ASTM A153,
• or coated with proprietary anti-corrosion coatings.
• For maximum corrosion protection, fasteners made from 302, 304, 305 or 316 stainless steel (18-8)
should be considered.

Below is a list of TFC brand fasteners that is acceptable for use in ACQ treated lumber or Fire Rated lumber.

1. BLAZER® Drill Screws for wood-to-metal applications coated with TRI-SEAL™ long-life ceramic
topcoat.
2. CONCEALOR® Low Profile Pancake head screws coated with TRI-SEAL™ long-life ceramic topcoat.
3. CONCEALOR® ULP Ultra Low Profile head screws coated with TRI-SEAL™ long-life ceramic topcoat.
4. PANEL-TITE® Post Frame metal-to-wood screws coated with TRI-SEAL™ long-life ceramic topcoat.
5. PANEL-TITE® SS Post Frame metal-to-wood screws made of 305 stainless steel.
6. SENTRY PLUS FIVE® Roofing Fasteners coated with an electro-coated epoxy
(E-coat) topcoat.
NOTE: Approved for the attachment of treated wood to metal or concrete. Approved for the attachment
of a prepunch roof clip to treated wood. Not approved for the attachment of metal panel, trim or siding
to treated wood where the screw must penetrate the steel.
7. TRACER® Drywall screws coated with TRI-SEAL™ long-life ceramic topcoat.
8. TRI-SEAL™ Long-life coated screws.
9. Any fastener made from 300 series stainless steel.
10. Any fastener made from 410 stainless steel

Note: Estimating service life of fasteners in ACQ treated lumber cannot be determined due to variables
uncontrollable by TFC. Stainless steel screws are recommended. It is important that if carbon steel fasteners
are used, they are at the least coated with a finish that provides protection equal to or better than hot dipped
galvanized like the ones listed above. Determining the proper fastener is the responsibility of the user or specifier,
who assumes all risks and liabilities.

Rev. Date: 3.1.13

TRIANGLE FASTENER CORPORATION PAGE 23 800.486.1832 | www.trianglefastener.com

MD 254
Visit our website for the most up-to-date product and technical information!
 R
Technical Data
C
tri-seal™ long-life coating
TRI-SEAL™ Long-Life Coating is a high performance dip spin finish,
developed to minimize corrosion when used in exterior building applications. It
consists of three layers; the first layer is a metallic zinc layer, the second layer
is a high-grade anti-corrosion chemical conversion film and the third, outer
layer, is a baked ceramic surface coating.

The distinguishing feature of TRI-SEAL™ is the tight joining of the baked

ceramic surface coating and the chemical conversion film. These two layers
are bonded together through chemical reactions, and this unique method of
combining layers result in a rigid combination of the coating films.
Salt Spray Test Results ■■ Excellent resistance against gas, weather, and other kinds
1,000hrs Per ASTM B117 of corrosion factors, including salt water.
No Red Rust ■■ Compatible for use in ACQ and Fire Treated Lumber.
■■ Composite layers minimize the effect of scratches on the
Compatible for use in treated lumber protection coating.
■■ Compatible for use in aluminum applications.
sem imaging
Layer 1 - Baked Ceramic Surface Coating Layer
Corrosive elements are intercepted by the
strong paint film made of ceramic materials.

Layer 2 - Chemical Conversion Coating Layer

Rust proof performance is improved as the
chemical conversion inactivates the zinc plated
surface and creates a tight adhesion between
the chemically converted layer and the
paint layer.

Layer 3 - Metallic Zinc Layer

The steel / iron substrate is protected from
corrosion by the self-sacrificial galvanic effect
of the zinc coating.

Layer 4 - Fastener

Material properties
Test Items Test Methods Test Results
Corrosion Testing
Hardness Peeling test by pencil hardness Over 4H Salt Spray: 1,000hrs.
Peeling test by adhesive tape on cross scribed test
Per ASTM B117.
Adhesion Nothing abnormal No red rust
piece in 1 mm width

Acid Resistance Immersion in 5% sulfuric acid solution for 24 hours Nothing abnormal Kesternich:
30 cycles | 1.0 L
Alkali Resistance Immersion in 5% sodium hydroxide solution for 72 hours Nothing abnormal 15 cycles | 2.0 L
ASTM G87
No Red Rust
Heat Resistance Exposure to 250 C (482 F) heat for an hour Nothing abnormal

Accelerated Weathering Sunshine weather-0-meter test for 1,000 hours Free from red rust

Clearly superior to zinc

Corrosive investigation after Salt Spray Test (JIS Z2371)
Contact Corrosion electroplated (colored
done comparatively on surface treated steel bolts/nuts
w/other Metals chromate) and hot
tightened on a stainless steel plate
dip galvanizing

Contact TFC for additional details on TRI-SEALTM.

DISCLAIMER: All test results and specifications are a result of laboratory tests. Appropriate safety factors should be used by the
user or specifier. Determining the proper fastener is the responsibility of the user or specifier. Since application conditions vary
and are uncontrollable by TFC, we assume no liability for the use of this information.

TRIANGLE FASTENER CORPORATION PAGE 24 800.486.1832 | www.trianglefastener.com

MD 21
Visit our website for the most up-to-date product and technical information!
 R
Technical Data
C
CORROSION Protection INFORMATION
The following information was compiled from known data that compares various
finishes in a controlled environment. The material set forth herein is for general
information only and cannot be construed as a substitute for competent professional
advice or service. Any part considering application use of this information does so
at their own risk and assumes any and all liability from application or use. Consult
a corrosion specialist to determine the best fastener for your condition.

salt spray results SALT SPRAY Per ASTM F1941 & B117 (0% red rust) Rev. 042111
The chart to the right provides general information with Carbon steel and 410 stainless steel materials.
regard to corrosion resistance of various plating and Coating Salt Spray
coatings in a controlled test. Generally, thicker plating .00015” min. (3 um) zinc plating with clear chromate 15hrs
.0002” min. (6um) zinc plating with clear chromate 24hrs
produces more corrosion resistance. Passivated 410 Stainless Steel 48hrs
.0003” min. (8 um) zinc plating with clear chromate 48hrs
.0003” min. (8 um) zinc plating with yellow di-chromate 120hrs
.0005” min. (12 um) zinc plating with clear chromate 72hrs
.0007” min. (14 um) mechanical zinc with clear chromate 96hrs
Epoxy (E-Coat) (ACQ Compatible) 100hrs
TRI-SEAL™ Long-life coating 1,000hrs

NOTE: Per ASTM B965. Salt spray results should not be regarded as a direct guide to corrosion
resistance in all environments where the material is used. Performance of the different platings/
coating cannot always be taken as a direct guide to the relative corrosion resistance in service.

Fastener Material Selection Based on the Galvanic Series of Metals Revised by TFC: 0315JS
Table developed using information supplied by AISI Committee of Stainless Steel Producers.

FASTENER MATERIAL
STEEL STAINLESS STEEL STAINLESS STEEL
Zinc Plated Type 410 Type 302, 304, 316 ALUMINUM
Zinc | Galvanized | ZN/Al
A C C B
BASE METAL

Coated Steel
Aluminum A 1Not Recommended B A
Steel / Cast Iron A,D C B A
Brass, Copper, Bronze A,D,E A B A,E
Stainless Steel
A,D,E A A A,E
300 Series

Key
A. The corrosion of the base metal is not increased by the fastener.
B. The corrosion of the base metal is slightly increased by the fastener.
C. The corrosion of the base metal may be considerably increased by the fastener material.
D. The plating on the fastener is rapidly consumed.
E. The corrosion of the fastener is increased by the base metal.
Footnotes
1. Because aluminum can expand a large distance, the high hardness of 410 SS case harden screws may lead to screw to
failure due to lack of ductility or stress corrosion cracking.

NOTE: Organic coating applied to the screw will improve the corrosion resistance. Environments can affect the rate of
corrosion and change the activity of the metals.

Special Note: Preservative-Treated Lumber Applications

ACQ, Penta, CA or CBA preservative-treated lumber can be incompatible with certain types of fasteners. In those cases where any type
of metal roof or wall cladding materials are being attached to preservative treated lumber, the following fasteners are not compatible: zinc
plated screws, zinc-alloy headed screws, stainless capped screws, aluminum, copper and copper alloy. When attaching metal panels to
those types of preservative-treated lumber, a moisture barrier should be used between the lumber and the panel material. Metal panel
fasteners that are compatible with preservative-treated lumber are stainless steel fasteners, or hot dip galvanized nails manufactured
to ASTM A153 class D or heavier. Other types of fasteners coated with proprietary anti-corrosive technologies are also available for use
with preservative-treated lumber. In addition, zinc-plated screws can be used in CCA and MCQ pressure-treated lumber.

TRIANGLE FASTENER CORPORATION PAGE 25 800.486.1832 | www.trianglefastener.com

MD 20
Visit our website for the most up-to-date product and technical information!
 C
R

Guide to the selection of fasteners used in exposed

metal building and roofing applications

Environments Select a fastener based on the environment and the panel type.
To minimize galvanic corrosion, it is important that the fastener material is compatible with the roofing material.
URBAN/RURAL The following list of fasteners were selected based on specifications from various panel producers throughout
INDUSTRIAL
the world.
Coastal/MARINE
Contact the panel manufacturer for their specific recommendations.

NOTE: Electroplated zinc plated screws are not for use in exterior applications and will corrode quickly.
Panel Material Fasteners 304
*410 Stainless Cap WR Zinc Head WR Stainless Steel WR
COATED STEEL Carbon Steel Stainless Steel URBAN/RURAL URBAN/RURAL URBAN/RURAL
TRI-SEAL Coated URBAN/RURAL INDUSTRIAL INDUSTRIAL INDUSTRIAL
URBAN/RURAL INDUSTRIAL Coastal/MARINE Coastal/MARINE Coastal/MARINE

• Galvanized
• Zinc/Aluminum
• Painted Metal
*Organic Coated
or Zinc Plated
WR Use With Warranted Roof Systems Note: 300 series stainless may corrode the base metal in severe marine environments.
Consult the panel manufacturer for specific conditions
Panel Material Fasteners 304
ALUMINUM Carbon Steel Stainless Cap WR Zinc Head WR Stainless Steel WR
URBAN/RURAL URBAN/RURAL URBAN/RURAL
TRI-SEAL Coated INDUSTRIAL INDUSTRIAL INDUSTRIAL
URBAN/RURAL Coastal/MARINE Coastal/MARINE Coastal/MARINE

WR Use With Warranted Roof Systems

Panel Material Fasteners *410

304
Stainless Cap WR Stainless Steel WR
Stainless Steel URBAN/RURAL URBAN/RURAL
COPPER URBAN/RURAL
INDUSTRIAL
INDUSTRIAL
Coastal/MARINE
INDUSTRIAL
Coastal/MARINE

*Organic Coated
or Zinc Plated

WR Use With Warranted Roof Systems

Panel Material Fasteners *410

304
Stainless Cap WR Stainless Steel WR
STAINLESS Stainless Steel URBAN/RURAL URBAN/RURAL
URBAN/RURAL INDUSTRIAL INDUSTRIAL
STEEL INDUSTRIAL Coastal/MARINE Coastal/MARINE

*Organic Coated
or Zinc Plated

WR Use With Warranted Roof Systems

For detailed product information, please view our product page located on our website or our PRODUCT QUICK FACTS sheet.

BLAZER PANEL-TITE TFC TAPPERS SD300

R
R

DRILL SCREWS METAL-TO-WOOD SCREWS SELF-TAPPING SCREWS 304 Stainless Self-Drill Screws

• TRI-SEAL Coated | Carbon Steel • TRI-SEAL Coated | Carbon Steel • TRI-SEAL Coated | Carbon Steel • 304 Stainless Steel
• Stainless Cap or Zinc Head • Stainless Steel Cap Head Screws • Stainless Steel Cap Head Bi-Metal Drill Screws
• 410 Stainless Steel • 304 Stainless Steel • 304 Stainless Steel
Form # JS0413

TRIANGLE FASTENER CORPORATION PAGE 26 800.486.1832 | www.trianglefastener.com

MD 278
Visit our website for the most up-to-date product and technical information!
 FastenING Tips Specifying and Installation
The following information is provided to help you specify and install tapping screws correctly.
Care should be used when selecting and installing screws to assure optimal performance.
TERMINOLOGY
To eliminate confusion and assure the proper screw is used, specifications Head SCREW LENGTH
for tapping screws should be written to include; Type THREADS
1. Thread diameter PER INCH
2. Threads per inch Example
3. Point type 1/4-14 x 1” DP3 BLAZER Drill Screw. 3/8” HWH. POINT
4. Description of the type of screw Carbon Steel. TRI-SEAL™ 1,000 hour coating. TYPE
5. Drive size Thread Threads Screw Point Head Size
6. Head Style Diameter Per Inch Length Type & Type
7. Material 1/4 - 14 x 1” DP3 3/8” HWH THREAD
PILOT
8. Finish / plating DIAMETER
LENGTH

Determine Drill Point Type Determine Fastener Length

Drilling Thickness (Drill Point Type)
Add up the total thickness that will be drilled
by the screw and select a drill point type that
meets the required drilling thickness range. Attachment Thickness | METAL
(Do not include pre-punched materials that Measure from the top surface of the material
will not be drill by the screw.) being fastened to the underside of the metal. Be
Attachment
sure to allow for any void or insulation.
Select the desired drill point type located * Thickness

on the size chart of the BLAZER® / * Select a screw length listed in the BLAZER or
CONCEALOR® sell sheet (i.e. DP5). CONCEALOR® sell sheet (attachment length).
* Drilling Thickness

INSTALLATION TECHNIQUES Allow at least three (3) full

threads to extend beyond the
Recommended Screw-Gun Speed material being fastened.
Using the proper tooling is important for
producing consistent installation. It also
minimizes potential screw or application
failure caused by over-driven and
under-driven fasteners. Attachment Thickness | WOOD
Allow full penetration into wood decks so
Screw Size Max RPM the screw point extends beyond the bottom
#6, #8, #10 2,500 side. Allow at least 1” screw embedment in
All wood screws 2,500 2 x structures to maintain designed pull out
#12, 1/4”, 5/16” 2,000 resistance. Greater penetration can achieve
All DP5 2,000 higher pull out values.
304 Stainless Screws 1,200 Allow screw tip to extend beyond decking.

DO
• Install fastener perpendicular
WARNING! DO NOT USE IMPACT TOOLS to the work surface.
FOR INSTALLATION! • Let the drill point do the work.
Using impact tools to install pancake head screws can cause
the head to separate from the body due to the high torque and • Use a tool with torque control
or depth sensing nose piece
impulse generate by the tool. HWH screws can also be easily to prevent over-torqued and
overtighten which can lead to connection failure. under-torqued screws.
• Allow all material to be drilled
TFC is not responsible for failures caused by the use of improper before tapping into the steel.
tooling or improper installation.
DO NOT
• Do not exert excessive pressure!
Accessory Tips • Do not over drive the screw!
Look familiar? SET THE MAGNET!
• Do not use impact tools! (They
Be sure screw head
engages into the can torque the screw to failure!)
socket completely.
This will eliminate
screw wobble,
SEALING WASHERS Correct
improve the drilling To assure a proper seal, tighten the screw
Worn out drive bits and sockets performance, and until the EPDM sealant extrudes just to the
Too Tight!
reduce damage to outer edge of the backing material. This also
produces poor drilling, can strip
painted screw heads.
the recess, and damage painted Correct Incorrect is a great way to visually inspect the screw to
fasteners. assure it is properly sealed. Too Loose!

Disclaimer: Hardware should always be installed by a competent professional with a good understanding of interior wall types and mounting fasteners. Please do not attempt
to install any hardware unless you know how to safely operate the necessary tools, and have a good understanding of what you are doing. The following instructions are basic
guidelines for qualified installers, and should be read through completely before starting your job.
REV081715JS
TRIANGLE FASTENER CORPORATION PAGE 27 800.486.1832 | www.trianglefastener.com
MD 279
Visit our website for the most up-to-date product and technical information!
 FastenING Tips Tools and Accessories
The following information is provided to help you install tapping
screws correctly in metal roofing and siding applications.
SCREW GUNS
Using the proper tooling is important for producing consistent installation. It also
reduces the chance for screw or application failure caused by over-driven and
under-driven fasteners.

Screw-Gun Selection
For the best performance, we recommend the following RPM and DeWalt screw-guns.
Corded Tools Cordless Tools
DW267 DC668KA
DW268
DW269

Screw Size Max RPM Model Screw Size Max RPM Model
#6, #8, #10, #12, #14 2,500 DW268 All Screws 0 - 2,700 DC668KA
1/4”, 5/16”, all DP5 2,000 DW267
304SS Tapping Screws 1,000 DW269
Use a tool with torque control or depth sensing nose piece to
prevent over-torqued and under-torqued screws.

WARNING! DO NOT USE IMPACT TOOLS FOR INSTALLATION!

Using impact tools to install pancake head screws can cause the head to separate from the body due to the high torque and
impulse generate by the tool. Impact tools can also chip the paint on the head of the screw.
TFC is not responsible for failures caused by the use of improper tooling or improper installation.

Accessory Tips

Paint chipping or SET THE MAGNET!

stripping out recess? Be sure screw head engages into the socket
completely. This will eliminate screw wobble,
improve the drilling performance, and reduce
damage to painted screw heads.
Worn out drive bits and sockets produces poor
drilling, can strip the recess, and damage painted
Correct Incorrect
fasteners. Use only high quality bits and sockets.

INSTALLATION TECHNIQUES Determine Screw Length

METAL SUBSTRATE
DO Measure from the top surface of the material being fastened to the
• Install fastener perpendicular underside of the metal. Be sure to allow for any void or insulation.
to the work surface. Select a screw length that is at least 1" longer than the attachment length.
• Let the drill point do the work. WOOD SUBSTRATE
• Allow all material to be drilled Allow full penetration into wood decks so the screw point extends beyond
before tapping occurs. the bottom side. Allow at least 1” screw embedment in 2 x structures to
maintain designed pull out resistance. Greater penetration can achieve
DO NOT higher pull out values.
• Do not exert excessive pressure!
• Do not over drive the screw! SEALING WASHERS Correct
• Do not use impact tools! (They To assure a proper seal, tighten the screw
can torque the screw to failure!) until the EPDM sealant extrudes just to the
Too Tight!
outer edge of the backing material. This also
is a great way to visually inspect the screw to
assure it is properly sealed. Too Loose!

Disclaimer: Hardware should always be installed by a competent professional with a good understanding of interior wall types and mounting fasteners. Please do not attempt
to install any hardware unless you know how to safely operate the necessary tools, and have a good understanding of what you are doing. The following instructions are basic
guidelines for qualified installers, and should be read through completely before starting your job.
PS110615JS
TRIANGLE FASTENER CORPORATION PAGE 28 800.486.1832 | www.trianglefastener.com
MD 294
Visit our website for the most up-to-date product and technical information!