Product Sample & Technical Tools & Support & Reference

Folder Buy Documents Software Community Design

SN74LVC2G14
SCES200O – APRIL 1999 – REVISED AUGUST 2015

SN74LVC2G14 Dual Schmitt-Trigger Inverter

1 Features 3 Description
•
1 Available in the TI NanoFree™ Package This dual Schmitt-trigger inverter is designed for
1.65-V to 5.5-V VCC operation.
• Supports 5-V VCC Operation
• Inputs Accept Voltages to 5.5 V NanoFree™ package technology is a major
breakthrough in IC packaging concepts, using the die
• Max tpd of 5.4 ns at 3.3 V as the package.
• Low-Power Consumption, 10-μA Maximum ICC
The SN74LVC2G14 device contains two inverters
• ±24-mA Output Drive at 3.3 V and performs the Boolean function Y = A. The device
• Typical VOLP (Output Ground Bounce) functions as two independent inverters, but because
<0.8 V at VCC = 3.3 V, TA = 25°C of Schmitt action, it may have different input threshold
• Typical VOHV (Output VOH Undershoot) levels for positive-going (VT+) and negative-going
>2 V at VCC = 3.3 V, TA = 25°C (VT–) signals.
• Ioff Supports Live Insertion, Partial-Power-Down This device is fully specified for partial-power-down
Mode, and Back-Drive Protection applications using Ioff. The Ioff circuitry disables the
outputs, preventing damaging current backflow
• Support Translation Down through the device when it is powered down.
(5 V to 3.3 V; 3.3 V to 1.8 V)
• Latch-Up Performance Exceeds 100 mA Device Information(1)
Per JESD 78, Class II PART NUMBER PACKAGE BODY SIZE (NOM)
SN74LVC2G14DBV SOT-23 (6) 2.90 mm × 1.60 mm
2 Applications SN74LVC2G14DCK SC70 (6) 2.00 mm × 1.25 mm

• Body Control Modules SN74LVC2G14YZP DSBGA (6) 1.41 mm × 0.91 mm

• Engine Control Modules (1) For all available packages, see the orderable addendum at
the end of the data sheet.
• Arcade, Casino, and Gambling Machines
• Servers and High-Performance Computing
• EPOS, ECR, and Cash Drawer
• Routers
• Desktop PC
Block Diagram
1 6
1A 1Y

3 4
2A 2Y

An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
SN74LVC2G14
SCES200O – APRIL 1999 – REVISED AUGUST 2015 www.ti.com

Table of Contents
1 Features .................................................................. 1 8.1 Overview ................................................................... 8
2 Applications ........................................................... 1 8.2 Functional Block Diagram ......................................... 8
3 Description ............................................................. 1 8.3 Feature Description................................................... 8
8.4 Device Functional Modes.......................................... 8
4 Revision History..................................................... 2
5 Pin Configuration and Functions ......................... 3 9 Application and Implementation .......................... 9
9.1 Application Information.............................................. 9
6 Specifications......................................................... 4
9.2 Typical Application ................................................... 9
6.1 Absolute Maximum Ratings ..................................... 4
6.2 ESD Ratings ............................................................ 4 10 Power Supply Recommendations ..................... 10
6.3 Recommended Operating Conditions ...................... 4 11 Layout................................................................... 10
6.4 Thermal Information .................................................. 5 11.1 Layout Guidelines ................................................. 10
6.5 Electrical Characteristics........................................... 5 11.2 Layout Example .................................................... 11
6.6 Switching Characteristics, –40°C to 85°C ................ 6 12 Device and Documentation Support ................. 12
6.7 Switching Characteristics, –40°C to 125°C............... 6 12.1 Community Resources.......................................... 12
6.8 Operating Characteristics.......................................... 6 12.2 Trademarks ........................................................... 12
6.9 Typical Characteristics .............................................. 6 12.3 Electrostatic Discharge Caution ............................ 12
7 Parameter Measurement Information .................. 7 12.4 Glossary ................................................................ 12
8 Detailed Description .............................................. 8 13 Mechanical, Packaging, and Orderable
Information ........................................................... 12

4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.

Changes from Revision N (June 2015) to Revision O Page

• Added TJ junction temperature spec to Abs Max Ratings...................................................................................................... 4

Changes from Revision M (November 2013) to Revision N Page

• Added Applications, Device Information table, ESD Ratings table, Feature Description section, Device Functional
Modes, Application and Implementation section, Power Supply Recommendations section, Layout section, Device
and Documentation Support section, and Mechanical, Packaging, and Orderable Information section .............................. 1

2 Submit Documentation Feedback Copyright © 1999–2015, Texas Instruments Incorporated

Product Folder Links: SN74LVC2G14

 SN74LVC2G14
www.ti.com SCES200O – APRIL 1999 – REVISED AUGUST 2015

5 Pin Configuration and Functions

DBV Package
6-Pin SOT-23 DCK Package
Top View 6-Pin SC70
Top View

1A 1 6 1Y 1A 1 6 1Y

GND 2 5 VCC
GND 2 5 VCC
2A 3 4 2Y
2A 3 4 2Y

YZP Package
6-Pin DSBGA
Bottom View

2A 3 4 2Y
GND 2 5 VCC
1A 1 6
1Y

See mechanical drawing for dimensions.

Pin Functions
PIN
I/O DESCRIPTION
NAME NO.
1A 1 I Gate 1 logic signal
1Y 6 O Gate 1 inverted signal
2A 3 I Gate 2 logic signal
2Y 4 O Gate 2 inverted signal
GND 2 — Ground
VCC 5 — Supply/Power Pin

Copyright © 1999–2015, Texas Instruments Incorporated Submit Documentation Feedback 3

Product Folder Links: SN74LVC2G14
SN74LVC2G14
SCES200O – APRIL 1999 – REVISED AUGUST 2015 www.ti.com

6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted) (1)
MIN MAX UNIT
VCC Supply voltage –0.5 6.5 V
(2)
VI Input voltage –0.5 6.5 V
VO Voltage applied to any output in the high-impedance or power-off state (2) –0.5 6.5 V
VO Voltage applied to any output in the high or low state (2) (3) –0.5 VCC + 0.5 V
IIK Input clamp current VI < 0 –50 mA
IOK Output clamp current VO < 0 –50 mA
IO Continuous output current ±50 mA
Continuous current through VCC or GND ±100 mA
TJ Junction temperature –65 150 °C
Tstg Storage temperature –65 150 °C

(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) The input negative-voltage and output voltage ratings may be exceeded if the input and output clamp-current ratings are observed.
(3) The value of VCC is provided in the Recommended Operating Conditions table.

6.2 ESD Ratings

VALUE UNIT
(1)
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001 ±2000
V(ESD) Electrostatic discharge Charged-device model (CDM), per JEDEC specification JESD22- V
±1000
C101 (2)

(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process. Manufacturing with
less than 500-V HBM is possible with the necessary precautions. Pins listed as ±XXX V may actually have higher performance.
(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process. Manufacturing with
less than 250-V CDM is possible with the necessary precautions. Pins listed as ±YYY V may actually have higher performance.

6.3 Recommended Operating Conditions

(1)
See
MIN MAX UNIT
Operating 1.65 5.5
VCC Supply voltage V
Data retention only 1.5
VI Input voltage 0 5.5 V
VO Output voltage 0 VCC V
VCC = 1.65 V –4
VCC = 2.3 V –8
IOH High-level output current –16 mA
VCC = 3 V
–24
VCC = 4.5 V –32
VCC = 1.65 V 4
VCC = 2.3 V 8
IOL Low-level output current 16 mA
VCC = 3 V
24
VCC = 4.5 V 32
TA Operating free-air temperature –40 125 °C

(1) All unused inputs of the device must be held at VCC or GND to ensure proper device operation. Refer to the TI application report,
Implications of Slow or Floating CMOS Inputs, SCBA004.

4 Submit Documentation Feedback Copyright © 1999–2015, Texas Instruments Incorporated

Product Folder Links: SN74LVC2G14

 SN74LVC2G14
www.ti.com SCES200O – APRIL 1999 – REVISED AUGUST 2015

6.4 Thermal Information

SN74LVC2G14
THERMAL METRIC (1) DBV (SOT23) DCK (SC70) YZP (DSBGA) UNIT
6 PINS 6 PINS 6 PINS
RθJA Junction-to-ambient thermal resistance 215 259 139 °C/W
RθJC(top) Junction-to-case (top) thermal resistance 55 87 18 °C/W
RθJB Junction-to-board thermal resistance 57 89 N/A °C/W

(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report, SPRA953.

6.5 Electrical Characteristics

over recommended operating free-air temperature range (unless otherwise noted)
–40°C to 85°C –40°C to 125°C
PARAMETER TEST CONDITIONS VCC UNIT
MIN TYP (1) MAX MIN TYP (1) MAX
1.65 V 0.7 1.4 0.7 1.4
2.3 V 1 1.7 1 1.7
VT+
Positive-going input 3V 1.3 2.2 1.3 2.2 V
threshold voltage
4.5 V 1.9 3.1 1.9 3.1
5.5 V 2.2 3.7 2.2 3.7
1.65 V 0.3 0.7 0.3 0.7
2.3 V 0.4 1 0.4 1
VT–
Negative-going input 3V 0.6 1.3 0.6 1.3 V
threshold voltage
4.5 V 1.1 2 1.1 2
5.5 V 1.4 2.5 1.4 2.5
1.65 V 0.3 0.8 0.3 0.8
2.3 V 0.4 0.9 0.4 0.9
ΔVT
Hysteresis 3V 0.4 1.1 0.4 1.1 V
(VT+ – VT–)
4.5 V 0.6 1.3 0.6 1.3
5.5 V 0.7 1.4 0.7 1.4
IOH = –100 μA 1.65 V to 4.5 V VCC – 0.1 VCC – 0.1
IOH = –4 mA 1.65 V 1.2 1.2
IOH = –8 mA 2.3 V 1.9 1.9
VOH V
IOH = –16 mA 3V 2.4 2.4
IOH = –24 mA 3V 2.3 2.3
IOH = –32 mA 4.5 V 3.8 3.8
IOL = 100 μA 1.65 V to 4.5 V 0.1 0.1
IOL = 4 mA 1.65 V 0.45 0.45
IOL = 8 mA 2.3 V 0.3 0.3
VOL V
IOL = 16 mA 3V 0.4 0.4
IOL = 24 mA 3V 0.55 0.55
IOL = 32 mA 4.5 V 0.55 0.55
II A input VI = 5.5 V or GND 0 to 5.5 V ±5 ±5 μA
Ioff VI or VO = 5.5 V 0 ±10 ±10 μA
ICC VI = 5.5 V or GND, IO = 0 1.65 V to 5.5 V 10 10 μA
One input at VCC – 0.6 V,
ΔICC 3 V to 5.5 V 500 500 μA
Other inputs at VCC or GND
CI VI = VCC or GND 3.3 V 4 pF

(1) All typical values are at VCC = 3.3 V, TA = 25°C.

Copyright © 1999–2015, Texas Instruments Incorporated Submit Documentation Feedback 5

Product Folder Links: SN74LVC2G14
SN74LVC2G14
SCES200O – APRIL 1999 – REVISED AUGUST 2015 www.ti.com

6.6 Switching Characteristics, –40°C to 85°C

over recommended operating free-air temperature range (unless otherwise noted) (see Figure 3)
VCC = 1.8 V VCC = 2.5 V VCC = 3.3 V VCC = 5 V
FROM TO ± 0.15 V ± 0.2 V ± 0.3 V ± 0.5 V
PARAMETER UNIT
(INPUT) (OUTPUT)
MIN MAX MIN MAX MIN MAX MIN MAX
tpd A Y 3.9 9.5 1.9 5.7 2 5.4 1.5 4.3 ns

6.7 Switching Characteristics, –40°C to 125°C

over recommended operating free-air temperature range (unless otherwise noted) (see Figure 3)
VCC = 1.8 V VCC = 2.5 V VCC = 3.3 V VCC = 5 V
FROM TO ± 0.15 V ± 0.2 V ± 0.3 V ± 0.5 V
PARAMETER UNIT
(INPUT) (OUTPUT)
MIN MAX MIN MAX MIN MAX MIN MAX
tpd A Y 3.9 10.5 1.9 6.5 2 6 1.5 4.7 ns

6.8 Operating Characteristics

TA = 25°C
VCC = 1.8 V VCC = 2.5 V VCC = 3.3 V VCC = 5 V
PARAMETER TEST CONDITIONS UNIT
TYP TYP TYP TYP
Cpd Power dissipation capacitance f = 10 MHz 16 17 18 21 pF

6.9 Typical Characteristics

8
TPD
7

5
TPD (ns)
TPD (ns)

0
0 1 2 3 4 5 6
VCC (V) D002

Temperature (°C)

Figure 1. TPD Across Temperature at 3.3 V VCC Figure 2. TPD Across VCC at 25°C

6 Submit Documentation Feedback Copyright © 1999–2015, Texas Instruments Incorporated

Product Folder Links: SN74LVC2G14

 SN74LVC2G14
www.ti.com SCES200O – APRIL 1999 – REVISED AUGUST 2015

7 Parameter Measurement Information

VLOAD
RL S1 Open
From Output TEST S1
Under Test GND
tPLH/tPHL Open
CL
(see Note A) RL tPLZ/tPZL VLOAD
tPHZ/tPZH GND

LOAD CIRCUIT

INPUTS
VCC VM VLOAD CL RL VD
VI tr/tf
1.8 V ± 0.15 V VCC £2 ns VCC/2 2 × VCC 30 pF 1 kW 0.15 V
2.5 V ± 0.2 V VCC £2 ns VCC/2 2 × VCC 30 pF 500 W 0.15 V
3.3 V ± 0.3 V 3V £2.5 ns 1.5 V 6V 50 pF 500 W 0.3 V
5 V ± 0.5 V VCC £2.5 ns VCC/2 2 × VCC 50 pF 500 W 0.3 V

VI
Timing Input VM
0V
tW

VI tsu th
VI
Input VM VM Data Input VM VM
0V 0V
VOLTAGE WAVEFORMS VOLTAGE WAVEFORMS
PULSE DURATION SETUP AND HOLD TIMES

VI VI
VM VM Output
Input VM VM
Control
0V 0V
tPLH tPHL tPZL tPLZ
VOH Output VLOAD/2
VM VM Waveform 1
Output VM
S1 at VLOAD VOL + VD
VOL VOL
(see Note B)
tPHL tPLH tPZH tPHZ
VOH Output VOH
Waveform 2 VOH – VD
Output VM VM VM
VOL S1 at GND
(see Note B) »0 V
VOLTAGE WAVEFORMS VOLTAGE WAVEFORMS
PROPAGATION DELAY TIMES ENABLE AND DISABLE TIMES
INVERTING AND NONINVERTING OUTPUTS LOW- AND HIGH-LEVEL ENABLING

NOTES: A. CL includes probe and jig capacitance.

B. Waveform 1 is for an output with internal conditions such that the output is low, except when disabled by the output control.
Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control.
C. All input pulses are supplied by generators having the following characteristics: PRR £ 10 MHz, ZO = 50 W.
D. The outputs are measured one at a time, with one transition per measurement.
E. tPLZ and tPHZ are the same as tdis.
F. tPZL and tPZH are the same as ten.
G. tPLH and tPHL are the same as tpd.
H. All parameters and waveforms are not applicable to all devices.

Figure 3. Load Circuit and Voltage Waveforms

Copyright © 1999–2015, Texas Instruments Incorporated Submit Documentation Feedback 7

Product Folder Links: SN74LVC2G14
SN74LVC2G14
SCES200O – APRIL 1999 – REVISED AUGUST 2015 www.ti.com

8 Detailed Description

8.1 Overview
The SN74LVC2G14 device contains two Schmitt Trigger Inverter and performs the Boolean function Y = A. The
device functions as an independent inverter, but because of Schmitt Trigger action, it will have different input
threshold levels for a positive-going (Vt+) and negative-going (Vt-) signals.
This device is fully specified for partial-power-down applications using Ioff. The Ioff circuit disables the output,
preventing damaging current back-flow through the device when it is powered down.

8.2 Functional Block Diagram

1 6
1A 1Y

3 4
2A 2Y

8.3 Feature Description

8.3.1 Support Translation Down (5 V to 3.3 V; 3.3 V to 1.8 V)
As the inputs are 5.5-V tolerant, the device can be used as a down translator. When the input voltage exceeds
VT+ (Max), the output will follow VCC, performing down-translation if the input voltage exceeds VCC.

8.4 Device Functional Modes

Table 1 lists the functional modes of the SN74LVC2G14.

Table 1. Functional Table

(Each Inverter)
INPUT OUTPUT
A Y
H L
L H

8 Submit Documentation Feedback Copyright © 1999–2015, Texas Instruments Incorporated

Product Folder Links: SN74LVC2G14

 SN74LVC2G14
www.ti.com SCES200O – APRIL 1999 – REVISED AUGUST 2015

9 Application and Implementation

NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.

9.1 Application Information

The SN74LVC2G14 device is a high-drive CMOS device that can be used for a multitude of buffer type functions
where the input is slow or noisy. The device can produce 24 mA of drive current at 3.3 V, making it Ideal for
driving multiple outputs and good for high-speed applications up to 100 MHz. The inputs are 5.5-V tolerant
allowing it to translate down to VCC.

9.2 Typical Application

~2.2M 

SN74LVC2G14
(one channel)

50 pF

16 pF
~32 pF ~32pF

Figure 4. Typical Application Schematic

9.2.1 Design Requirements

This device uses CMOS technology and has balanced output drive. Care should be taken to avoid bus
contention because it can drive currents that would exceed maximum limits. The high drive will also create fast
edges into light loads so routing and load conditions should be considered to prevent ringing.

9.2.2 Detailed Design Procedure

1. Recommended Input Conditions
– Rise time and fall time specs. See (Δt/ΔV) in the Recommended Operating Conditions table.
– Specified high and low levels. See (VIH and VIL) in the Recommended Operating Conditions table.
– Inputs are overvoltage tolerant allowing them to go as high as (VI max) in the Recommended Operating
Conditions table at any valid VCC .
2. Recommend Output Conditions
– Load currents should not exceed (IO max) per output and should not exceed (continuous current through
VCC or GND) total current for the part. These limits are located in the Absolute Maximum Ratings table.
– Outputs should not be pulled above VCC.

Copyright © 1999–2015, Texas Instruments Incorporated Submit Documentation Feedback 9

Product Folder Links: SN74LVC2G14
SN74LVC2G14
SCES200O – APRIL 1999 – REVISED AUGUST 2015 www.ti.com

Typical Application (continued)

9.2.3 Application Curve
10
Icc 1.8V
9 Icc 2.5V
8 Icc 3.3V
Icc 5V
7
6

Icc - mA
5
4
3
2
1
0
0 20 40 60 80
Frequency - MHz D003

Figure 5. ICC vs Frequency

10 Power Supply Recommendations

The power supply can be any voltage between the minimum and maximum supply voltage rating located in the
table. Each VCC pin should have a good bypass capacitor to prevent power disturbance. For devices with a
single supply, TI recommends a 0.1-μF capacitor. If there are multiple VCC pins, then TI recommends a 0.01-μF
or 0.022-μF capacitor for each power pin. It is ok to parallel multiple bypass capacitors to reject different
frequencies of noise. 0.1-μF and 1-μF capacitors are commonly used in parallel. The bypass capacitor should be
installed as close to the power pin as possible for best results.

11 Layout

11.1 Layout Guidelines

When using multiple bit logic devices inputs should not ever float. In many cases, functions or parts of functions
of digital logic devices are unused, for example, when only two inputs of a triple-input AND gate are used or only
3 of the 4 buffer gates are used. Such input terminals should not be left unconnected because the undefined
voltages at the outside connections result in undefined operational states. The following rules must be observed
under all circumstances:
• All unused inputs of digital logic devices must be connected to a high or low bias to prevent them from
floating.
• The logic level that should be applied to any particular unused input depends on the function of the device.
Generally they will be tied to GND or VCC whichever make more sense or is more convenient.

10 Submit Documentation Feedback Copyright © 1999–2015, Texas Instruments Incorporated

Product Folder Links: SN74LVC2G14

 SN74LVC2G14
www.ti.com SCES200O – APRIL 1999 – REVISED AUGUST 2015

11.2 Layout Example

VDD

Keep signal traces as short as

possible 0.1µF
1A 1 6 1Y

GND 2
SN74LVC2G14 5
VCC

2A 3 4 2Y

Unused inputs connected to

GND or VCC to prevent
floating
Figure 6. Layout Schematic

Copyright © 1999–2015, Texas Instruments Incorporated Submit Documentation Feedback 11

Product Folder Links: SN74LVC2G14
SN74LVC2G14
SCES200O – APRIL 1999 – REVISED AUGUST 2015 www.ti.com

12 Device and Documentation Support

12.1 Community Resources

The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.

12.2 Trademarks
NanoFree, E2E are trademarks of Texas Instruments.
All other trademarks are the property of their respective owners.
12.3 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.

12.4 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.

13 Mechanical, Packaging, and Orderable Information

The following pages include mechanical packaging and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser based versions of this data sheet, refer to the left hand navigation.

12 Submit Documentation Feedback Copyright © 1999–2015, Texas Instruments Incorporated

Product Folder Links: SN74LVC2G14

 PACKAGE OPTION ADDENDUM

www.ti.com 4-Apr-2019

PACKAGING INFORMATION

Orderable Device Status Package Type Package Pins Package Eco Plan Lead/Ball Finish MSL Peak Temp Op Temp (°C) Device Marking Samples
(1) Drawing Qty (2) (6) (3) (4/5)

SN74LVC2G14DBVR ACTIVE SOT-23 DBV 6 3000 Green (RoHS CU NIPDAU | CU SN Level-1-260C-UNLIM -40 to 125 (C145, C14F, C14K,
& no Sb/Br) C14R)
SN74LVC2G14DBVRE4 ACTIVE SOT-23 DBV 6 3000 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -40 to 125 (C14F, C14R)
& no Sb/Br)
SN74LVC2G14DBVRG4 ACTIVE SOT-23 DBV 6 3000 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -40 to 125 (C14F, C14R)
& no Sb/Br)
SN74LVC2G14DBVT ACTIVE SOT-23 DBV 6 250 Green (RoHS CU NIPDAU | CU SN Level-1-260C-UNLIM -40 to 125 (C145, C14F, C14K,
& no Sb/Br) C14R)
SN74LVC2G14DBVTG4 ACTIVE SOT-23 DBV 6 250 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -40 to 125 (C14F, C14R)
& no Sb/Br)
SN74LVC2G14DCK3 ACTIVE SC70 DCK 6 3000 Pb-Free CU SNBI Level-1-260C-UNLIM -40 to 125 (CFF, CFZ)
(RoHS)
SN74LVC2G14DCKR ACTIVE SC70 DCK 6 3000 Green (RoHS CU NIPDAU | CU SN Level-1-260C-UNLIM -40 to 125 (CF5, CFF, CFJ, CF
& no Sb/Br) K, CFR)
SN74LVC2G14DCKRE4 ACTIVE SC70 DCK 6 3000 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -40 to 125 CF5
& no Sb/Br)
SN74LVC2G14DCKRG4 ACTIVE SC70 DCK 6 3000 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -40 to 125 CF5
& no Sb/Br)
SN74LVC2G14DCKT ACTIVE SC70 DCK 6 250 Green (RoHS CU NIPDAU | CU SN Level-1-260C-UNLIM -40 to 125 (CF5, CFF, CFJ, CF
& no Sb/Br) K, CFR)
SN74LVC2G14DCKTG4 ACTIVE SC70 DCK 6 250 Green (RoHS CU NIPDAU Level-1-260C-UNLIM -40 to 125 CF5
& no Sb/Br)
SN74LVC2G14YZPR ACTIVE DSBGA YZP 6 3000 Green (RoHS SNAGCU Level-1-260C-UNLIM -40 to 125 (CF7, CFN)
& no Sb/Br)

(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.

(2)
RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.

Addendum-Page 1
 PACKAGE OPTION ADDENDUM

www.ti.com 4-Apr-2019

Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.

(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.

(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.

(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.

(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.

Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.

In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.

OTHER QUALIFIED VERSIONS OF SN74LVC2G14 :

• Automotive: SN74LVC2G14-Q1

NOTE: Qualified Version Definitions:

• Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects

Addendum-Page 2
 PACKAGE MATERIALS INFORMATION

www.ti.com 7-Oct-2018

TAPE AND REEL INFORMATION

*All dimensions are nominal

Device Package Package Pins SPQ Reel Reel A0 B0 K0 P1 W Pin1
Type Drawing Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
SN74LVC2G14DBVR SOT-23 DBV 6 3000 178.0 9.2 3.3 3.23 1.55 4.0 8.0 Q3
SN74LVC2G14DBVRG4 SOT-23 DBV 6 3000 178.0 9.0 3.23 3.17 1.37 4.0 8.0 Q3
SN74LVC2G14DBVT SOT-23 DBV 6 250 178.0 9.2 3.3 3.23 1.55 4.0 8.0 Q3
SN74LVC2G14DBVTG4 SOT-23 DBV 6 250 178.0 9.0 3.23 3.17 1.37 4.0 8.0 Q3
SN74LVC2G14DCKR SC70 DCK 6 3000 178.0 9.2 2.4 2.4 1.22 4.0 8.0 Q3
SN74LVC2G14DCKR SC70 DCK 6 3000 180.0 9.2 2.3 2.55 1.2 4.0 8.0 Q3
SN74LVC2G14DCKRG4 SC70 DCK 6 3000 178.0 9.2 2.4 2.4 1.22 4.0 8.0 Q3
SN74LVC2G14DCKTG4 SC70 DCK 6 250 178.0 9.2 2.4 2.4 1.22 4.0 8.0 Q3
SN74LVC2G14YZPR DSBGA YZP 6 3000 178.0 9.2 1.02 1.52 0.63 4.0 8.0 Q1

Pack Materials-Page 1
 PACKAGE MATERIALS INFORMATION

www.ti.com 7-Oct-2018

*All dimensions are nominal

Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
SN74LVC2G14DBVR SOT-23 DBV 6 3000 180.0 180.0 18.0
SN74LVC2G14DBVRG4 SOT-23 DBV 6 3000 180.0 180.0 18.0
SN74LVC2G14DBVT SOT-23 DBV 6 250 180.0 180.0 18.0
SN74LVC2G14DBVTG4 SOT-23 DBV 6 250 180.0 180.0 18.0
SN74LVC2G14DCKR SC70 DCK 6 3000 180.0 180.0 18.0
SN74LVC2G14DCKR SC70 DCK 6 3000 205.0 200.0 33.0
SN74LVC2G14DCKRG4 SC70 DCK 6 3000 180.0 180.0 18.0
SN74LVC2G14DCKTG4 SC70 DCK 6 250 180.0 180.0 18.0
SN74LVC2G14YZPR DSBGA YZP 6 3000 220.0 220.0 35.0

Pack Materials-Page 2
 PACKAGE OUTLINE
DBV0006A SCALE 4.000
SOT-23 - 1.45 mm max height
SMALL OUTLINE TRANSISTOR

C
3.0
2.6 0.1 C
1.75
B A 1.45 MAX
1.45
PIN 1
INDEX AREA

1
6

2X 0.95
3.05
2.75
1.9 5
2

4
3
0.50
6X
0.25
0.15
0.2 C A B (1.1) TYP
0.00

0.25
GAGE PLANE 0.22
TYP
0.08

8
TYP 0.6
0 TYP SEATING PLANE
0.3

4214840/B 03/2018

NOTES:

1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. Body dimensions do not include mold flash or protrusion. Mold flash and protrusion shall not exceed 0.15 per side.
4. Leads 1,2,3 may be wider than leads 4,5,6 for package orientation.
5. Refernce JEDEC MO-178.

www.ti.com
 EXAMPLE BOARD LAYOUT
DBV0006A SOT-23 - 1.45 mm max height
SMALL OUTLINE TRANSISTOR

PKG
6X (1.1)
1

6X (0.6)
6

SYMM
2 5
2X (0.95)

3 4

(R0.05) TYP (2.6)

LAND PATTERN EXAMPLE

EXPOSED METAL SHOWN
SCALE:15X

SOLDER MASK
SOLDER MASK METAL METAL UNDER OPENING
OPENING SOLDER MASK

EXPOSED METAL EXPOSED METAL

0.07 MAX 0.07 MIN

ARROUND ARROUND

NON SOLDER MASK SOLDER MASK

DEFINED DEFINED
(PREFERRED)

SOLDER MASK DETAILS

4214840/B 03/2018

NOTES: (continued)

6. Publication IPC-7351 may have alternate designs.

7. Solder mask tolerances between and around signal pads can vary based on board fabrication site.

www.ti.com
 EXAMPLE STENCIL DESIGN
DBV0006A SOT-23 - 1.45 mm max height
SMALL OUTLINE TRANSISTOR

PKG
6X (1.1)
1

6X (0.6)
6

SYMM
2 5
2X(0.95)

3 4

(R0.05) TYP
(2.6)

SOLDER PASTE EXAMPLE

BASED ON 0.125 mm THICK STENCIL
SCALE:15X

4214840/B 03/2018

NOTES: (continued)

8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
9. Board assembly site may have different recommendations for stencil design.

www.ti.com
 PACKAGE OUTLINE
YZP0006 SCALE 9.000
DSBGA - 0.5 mm max height
DIE SIZE BALL GRID ARRAY

B E A

BALL A1
CORNER

0.5 MAX C

SEATING PLANE
0.19 BALL TYP 0.05 C
0.15

0.5 TYP

SYMM
1 D: Max = 1.418 mm, Min =1.358 mm
B TYP
0.5 E: Max = 0.918 mm, Min =0.858 mm
TYP
A

0.25 1 2
6X SYMM
0.21
0.015 C A B

4219524/A 06/2014

NOTES: NanoFree Is a trademark of Texas Instruments.

1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
TM
3. NanoFree package configuration.

www.ti.com
 EXAMPLE BOARD LAYOUT
YZP0006 DSBGA - 0.5 mm max height
DIE SIZE BALL GRID ARRAY

(0.5) TYP
6X ( 0.225)
1 2

(0.5) TYP

B SYMM

SYMM

LAND PATTERN EXAMPLE

SCALE:40X

( 0.225) 0.05 MAX 0.05 MIN METAL

METAL UNDER
MASK

SOLDER MASK ( 0.225)

OPENING SOLDER MASK
OPENING
NON-SOLDER MASK
DEFINED SOLDER MASK
(PREFERRED) DEFINED

SOLDER MASK DETAILS

NOT TO SCALE

4219524/A 06/2014

NOTES: (continued)

4. Final dimensions may vary due to manufacturing tolerance considerations and also routing constraints.
For more information, see Texas Instruments literature number SBVA017 (www.ti.com/lit/sbva017).

www.ti.com
 EXAMPLE STENCIL DESIGN
YZP0006 DSBGA - 0.5 mm max height
DIE SIZE BALL GRID ARRAY

(0.5) TYP

6X ( 0.25)
(R0.05) TYP
1 2
A

(0.5)
TYP

B SYMM

METAL
TYP

SYMM

SOLDER PASTE EXAMPLE

BASED ON 0.1 mm THICK STENCIL
SCALE:40X

4219524/A 06/2014

NOTES: (continued)

5. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release.

www.ti.com
 IMPORTANT NOTICE AND DISCLAIMER

TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you
permission to use these resources only for development of an application that uses the TI products described in the resource. Other
reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third
party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims,
damages, costs, losses, and liabilities arising out of your use of these resources.
TI’s products are provided subject to TI’s Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on
ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable
warranties or warranty disclaimers for TI products.

Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2019, Texas Instruments Incorporated