0% found this document useful (0 votes)
157 views10 pages

EasyScopeX Install Guide

The document provides instructions for installing EasyScopeX software. It lists hardware and software requirements including supported operating systems and the need to install .NET Framework 3.5 and NI-VISA. The installation process involves running the setup file, selecting an installation path, and completing the installation. Finally, the guide describes how to connect a device via USBTMC and verify communication by sending commands.

Uploaded by

Jamie
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
157 views10 pages

EasyScopeX Install Guide

The document provides instructions for installing EasyScopeX software. It lists hardware and software requirements including supported operating systems and the need to install .NET Framework 3.5 and NI-VISA. The installation process involves running the setup file, selecting an installation path, and completing the installation. Finally, the guide describes how to connect a device via USBTMC and verify communication by sending commands.

Uploaded by

Jamie
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 10

EasyScopeX Install Guide

1 Before Install
1.1 Hardware requirement

 1GHz or higher processor


 200M or more hard disk space
 1024x768 monitor resolution or above
 256M or more RAM
 USB interface and cable
 LAN interface and cable

1.2 System Support

 Microsoft Windows2000, XP system


 Win7 32bit and 64bit system
 Vista 32bit and 64bit system
 Windows 8 32bit and 64bit system.

1.3 Software requirement


1.3.1 NET framework 3.5 SP1

The application you are installing requires the Microsoft .NET framework version 3.5 to
run. You can download the Microsoft .NET Framework 3.5 SP1 package directly from
Microsoft. This is a small 3 MB download with just the .NET framework installer. When you
run it, the installer downloads the actual framework components that need to be installed on
your computer. Once you've installed the .NET framework, you can continue installing the
application.
If you plan to install version 3.5 of the .NET framework on a large number of computers,
you can also download the full package of the Microsoft .NET Framework 3.5 SP1. This 231
MB download comes directly from Microsoft. The small 3 MB installer likely needs to
download much less than this, depending on what is already present on your computer. The
install steps as below:
a. Double click the dotnetfx35.exe , launch the install process, dialog as shown below:
b. Choose ACCEPT, click Install, dialog as shown below:

c. Now software setup is finished

.Net Framework 3.5 was installed on the machine when installing Windows 7(64 bits) or
Windows Vista(64 bits), follow next steps to use it:
a. Open control panel, select Uninstall Program.
b. Select Open or Close Windows Functions in the new window.
c. Check Microsoft .Net Framework in the Windows Functions Dialog box,click OK
button.

1.3.2 NI-VISA

Before use this application, you have to install the NI-VISA runtime library, you can find it in
the installation folder or you can download it from NI-VISA web site. For example, you can
download NI-VISA Run-Time Engine 5.4 directly to your PC. Follow the steps below to install it:
a. Double click the visa540_runtime.exe, dialog show as below:

b. Click Unzip, the install process will launch after unzipping files, dialog as shown below:

c. Click Next, dialog as shown below:


d. Set the install path, default path is “C:\Program Files\National Instruments\”,
you can change it. Click next, dialog as shown below:

e. Click Next twice, dialog as shown below:


f. Accept the licenses, Click Next.

g. Click Next to begin installation.


h. Now Installation complete.

2 Install
a. Double click the EasyScopeX_setup.exe , launch the install process, dialog as shown
below:

b. Click next, dialog as shown below:


c. Set the install path, default path is “C:\Program Files\EasyScopeX”, you can change it,
click next, dialog as shown below:

d. Click next, dialog as shown below:


e. Click install, dialog as shown below:

f. Now software setup is finished.

3 Connect Device
For example, connect the device with PC on USBTMC protocol.
a. Launch EasyScopeX, the application as shown below.
b. Click Add Device Button, the Add Device dialog as shown below:

c. Click USBTMC, the Connect DeviceDLG as shown below:


d. Click the Add button to add it to the Scope Explorer, and you can communicate with the
device in the application. Input “*IDN?” in Send Commands text area, as below:

e. Pressing Enter key and then get the return information, the result as shown below:

You might also like