Scribd
Upload
78 views3 pages

Lecture 19 PDF

Logarithmic decrement is a tool to determine damping in a system through free vibration tests. It is defined as the natural logarithm of the ratio of the amplitudes between two successive peaks of vibration. The logarithmic decrement is a function only of damping and provides a means to estimate the damping present in a system based on measured peak amplitudes over multiple cycles. It can also be calculated using the amplitudes after several cycles rather than just successive peaks for better accuracy when damping is small.

Uploaded by

Md Sohail
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
78 views3 pages

Lecture 19 PDF

Logarithmic decrement is a tool to determine damping in a system through free vibration tests. It is defined as the natural logarithm of the ratio of the amplitudes between two successive peaks of vibration. The logarithmic decrement is a function only of damping and provides a means to estimate the damping present in a system based on measured peak amplitudes over multiple cycles. It can also be calculated using the amplitudes after several cycles rather than just successive peaks for better accuracy when damping is small.

Uploaded by

Md Sohail
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Module 8 : Free Vibration with Viscous Damping; Critical Damping and Aperiodic

Motion; Logarithmic Decrement; Systems with Coulomb Damping.

Lecture 19 : Logarithmic Decrement

Objectives
In this lecture you will learn the following.

Concept of logarithmic decrement

Formulation of equation for logarthmic decrement.

Application of the concept.

When “ < 1”, x(t) is a damped sinusoid and the system exhibits a vibratory motion whose amplitude
keeps diminishing as shown in fig 10.3.1. This is the most common vibration case and we will spend most of
our time studying such systems. These are referred to as Underdamped systems

Fig 8.3.1 Underdamped Oscillations

The decrease in amplitude from one cycle to the next depends on the extent of damping in the system. The
successive peak amplitudes bear a certain specific relationship involving the damping of the system,
leading us to the concept of "logarithmic decrement" which we will now discuss.

It is often necessary to estimate the extent of damping present in a given system. Essentially the
experimental techniques to determine damping in a system fall into two categories -- those based on free
vibration tests and secondly those based on forced vibration tests. The latter require more sophisticated
equipment/instruments, while the former is a relatively simple test. In a free vibration test, based on the
measured peak amplitudes over several cycles (and thus estimating the "logarithmic decrement"), one can
readily find the damping factor for the given system. We will now discuss these aspects.
Lograthmic decrement comes as an accurate and practically feasible tool to determine the damping in the
system.

Logarithmic Decrement:

Consider the two peaks A and B as shown in fig 8.3.1. The amplitude at A and B are and at time

and respectively.The periodic displacement from to represents a cycle. The time period for this
complete cycle is given by:

8.3.1

This is the time period of damped oscillations and is damped natural frequency.

The amplitude of damped oscillations is given by the expression:

8.3.2

which is the envelope of maximum of displacement -time curve. Therefore at t= and the amplitudes
are given by:

8.3.3

8.3.4

Therefore

8.3.5

Therefore 8.3.6

This is called the Logarithmic Decrement denoted by

8.3.7

if <<1
This shows that the ratio of any two succesive amplitudes for an underdamped system, vibrating freely , is
constant and is a function of the damping only.

Sometimes, in experiments, it is more convenient/accurate to measure the amplitudes after say "n" peaks
rather than two succesive peaks (because if the damping is very small, the difference between the succesive
peaks may not be significant). The lograthmic decrement can then be given by the equation

8.3.8

Recap
In this lecture you have learnt the following

Concept of logarithmic decrement and its application as a tool to determine the system damping

Derivation of formula for lograthmic decrement

Congratulations, you have finished Lecture 3. To view the next lecture select it from the left hand side
menu of the page

You might also like