Scribd
Upload
181 views4 pages

Set 3

This document contains radiographic reports for two welded carbon steel plates. Report 1 analyzes Plate A with a 16 mm thickness and identifies 5 defects including lack of root penetration and porosity. Report 2 analyzes Plate B with a 12 mm thickness and identifies 4 defects, among them lack of root penetration, a slag line, and slag inclusion. Both reports provide location details for each identified defect.

Uploaded by

mangalraj900
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
181 views4 pages

Set 3

This document contains radiographic reports for two welded carbon steel plates. Report 1 analyzes Plate A with a 16 mm thickness and identifies 5 defects including lack of root penetration and porosity. Report 2 analyzes Plate B with a 12 mm thickness and identifies 4 defects, among them lack of root penetration, a slag line, and slag inclusion. Both reports provide location details for each identified defect.

Uploaded by

mangalraj900
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOC, PDF, TXT or read online on Scribd
You are on page 1/ 4

SET 3A

RADIOGRAPHIC INTERPRETATION – REPORT

Radiographic Identification: - A-B-C-D

Inspector: - _______________________________

Date: - ______________ Course: ________

Material: Carbon Steel Plate Thickness: 16 mm

Weld Thickness: 19 mm

Welding Process: MMA Edge Preparation: Single V

KV/ Source: Ir 192/ 1.5 X 1.5 mm Screens: Pb

Film Type: D7 (AGFA) FFD/SFD: 300 mm

Type of IQI used: _______________________ Technique:300 mm

Number of wire visible: ____________________________________________________

Film Density: a) Weld Zone _______________________________________


b) Parent Plate _______________________________________

________________________________________________________________________

Report
1. Calculate the sensitivity level for this radiograph?

2. Calculate the geometric unsharpness (Ug) based on the parameters given?

3. Comments on Radiographic Quality

a. Sensitivity: ________________ b. Density: ________________

c. Technique: __________________________________________________
RADIOGRPHIC REPORT (Set 3A)

1. SINGLE WALL SINGLE IMAGE (SWSI)

0 150

1 1

List of defects:
1. Lack of root penetration (+68mm from datum, 8mm long)
(+ 180mm from datum, 174 mm long)

2. Scattered porosity (+137 mm from datum, throughout the length)

150 300
3
2
5

1
List of defects:
3. External Undercut (+282 from datum, 8mm long) 3
(+325 from datum, 8mm long)

4. Cluster porosity (+271 from datum, 18mm long)

SET 3B
RADIOGRAPHIC INTERPRETATION – REPORT
Radiographic Identification: - TP 30

Inspector: - _______________________________

Date: - ______________ Course: ________

Material: Carbon Steel Plate Thickness: 12 mm

Weld Thickness: 15 mm

Welding Process: MMA Edge Preparation: Single V

KV/ Source: 140 KV Screens: Pb

Film Type: D7 (AGFA) FFD/SFD:

Type of IQI used: _______________________ Technique: SWSI

Number of wire visible: ____________________________________________________

Film Density: a) Weld Zone _______________________________________


b) Parent Plate _______________________________________

________________________________________________________________________

Report
1.Calculate the sensitivity level for this radiograph?

2. Calculate the geometric unsharpness (Ug) based on the parameters given?

Not Required

3.Comments on Radiographic Quality

a. Sensitivity: ________________ b. Density: ________________

c. Technique: __________________________________________________
RADIOGRPHIC REPORT
Set 3B
1. SINGLE WALL SINGLE IMAGE (SWSI)

0 150

1 2 1

List of defects:
1. Lack of Root Penetration (+72 from datum, 32mm long)
(+164 from datum, 10mm long)
(+263 from datum, 9 mm long)

2. Slag line (Wagon Track) (+ 105 from datum, 191mm long)

3. Slag inclusion (+300 mm from datum, 12 mm long)

150 300

2 1 3

4
List of defects:

4. Excessive weld (at the edge of weld, 4 mm long)

You might also like