Dual Channel Vibration Monitor

DM200 Dual Channel A/V/D Vibration Monitor

Introduction

The DM200 is a dual channel vibration monitor. It is used to

monitor the absolute vibration with acceleration, velocity or
displacement of rotating machinery.

Features

9 Dual channel case vibration monitoring with

acceleration, velocity or displacement
9 Independent alert and danger dual relays on
each channel
9 Fully digital, long term stability Buffered Output:
9 IP 65 or NEMA 4X environmental rating Original vibration, un-filtered
Sensitivity/frequency response: same as the sensor
9 Bright 4 digit LED display
Impedance: < 100Ω
9 Front panel buffered output Maximum cable distance: 300m (1,000ft)
9 Wide power supply range Overall Vibration Output:
9 Cost effective 4－20mA source
Load resistance < 500Ω
Specifications System Not OK: Output < 3.5mA
Alarms:
Electrical Dual dry-contact relays on each channel
Power Supply: Each alarm can be programmed separately
90 －250VAC, 40 －60Hz, 0.5A Setting: 0－100% full scale
Frequency Response: (±3dB): Accuracy: ±0.1%
Relays (Alert/Danger):
Standard: 2.0 －3.0 KHz without integration
Seal: Epoxy
Integration: 10 – 3.0 KHz
Capacity: 3A/220VAC resistive load
Low frequency option: 0.5－100Hz
Relay Type: SPDT
External Sensor:
Isolation: 1000VDC
Accelerometer: 100 mV/g
Alarm Delay:
Velocity sensor: 4.0mV/mm/s
Factory programmable: 1-30 seconds with time interval
Low frequency sensor: 4.0mV/um
of 1 second (specify in order)
Other sensors: specify in order
Nominal 6 seconds
Sensor Power:
Trip Multiply:
Current mode sensor: 24VDC, 4mA
Factory programmable with a factor of 2 or 3 (specify in
Low frequency sensor: 24VDC, 3 wire
order)
Nominal factor or 3
RESET/ BYPASS:
Local RESET: The bottom “SET” button
Remote RESET/BYPASS
DM 200 PredicTech Display:
CH 1
DUAL VIBRATION MONITOR
CH 2 4 digit LED displays channel 1 and 2 in three seconds
OK/TX OK/TX interval.
ALARM ALARM
OK: channel ok indication
-
Alarm: alarm indication
SET +

ProvibTech Phone: +1-713-830-7601● Fax: +1-281-754-4972 ● [email protected] ● www.provibtech.com

 Dual Channel Vibration Monitor

Physical CX: Frequency Response

C0*: Normal Frequency (B2 not applicable)
Weight: 1,300 g (2.86 lbs) C1: Low Frequency (B2 only)
Installation: panel mount DX: Environmental Rating (Front Panel)
Dimension: see graphic D0*: No rating
D1: IP65 or NEMA 4X (buffered output and setting not
Environmental available)

Temperature * Factory default

o o
Operation:-20 C to +70 C
o
Storage:-40 C to +100 C
o Optional Accessories:
Humidity:
95% non-condensing DM200 works with an external accelerometer or velocity
With IP65 Rating or NEMA 4X: sensor as a system.
Front panel buffered output is unavailable.
Alarms setting and ZERO calibration is unavailable from TM0782A, TM0783A, TM0786A, TM016-782:
the front panel access. Accelerometers
TM0793V, TM0796V, TM016-793:
Ordering Information Velocity sensors
TM079VD:
DM200-AXX–BX-CX-DX Low frequency sensor
TM070X:
AXX: Full Scale Sensor cables
A00: 0 - 200um (8mil) pk-pk
A01: 0 - 500um (20mil) pk-pk
A02: 0 - 100um (4mil) pk-pk
A03: 0 - 250um (10mil) pk-pk
A05: 0 - 125um (5mil) pk-pk
A06*: 0 - 50mm/s (2.0 ips) pk
A07: 0 - 100mm/s (4.0 ips) pk
A08: 0 - 20mm/s (0.8 ips) pk
A11: 0 - 25mm/s (1.0 ips) pk
A12: 0 - 5.0g pk
A13: 0 - 10g pk
A26: 0 - 50mm/s (2.0 ips) rms
A27: 0 - 100mm/s (4.0 ips) rms
A28: 0 - 20mm/s (0.8 ips) rms
A31: 0 - 25 mm/s (1.0 ips) rms
BX: Sensor (not included)
B0*: TM0782A, TM0783A, TM0786A TM016-782 or any
ICP accelerometer with 100mV/g (A00-A05 not
applicable)
B1: TM0793V, TM0796V, TM016-793 or any ICP velocity
sensor with 4mV/mm/s (A12, 13 not applicable)
B2: TM079VD (A12, 13 not available)
BXXX: Seismic velocity sensor, Sensitivity = XXX
mV/in/sec (A12, 13 not available)

2
ProvibTech Phone: +1-713-830-7601● Fax: +1-281-754-4972 ● [email protected] ● www.provibtech.com
 Dual Channel Vibration Monitor

Field-Wiring Diagram

4-20mA(B)

4-20mA(A)
(+)
(+) B-4-20 A-4-20
(-) B-COM A-COM (-)

B-BUF A-BUF
Red B-PWR A-PWR Red
B-P/A A-P/A
White B-S/B A-S/B White
BUS+
Remote

TRIP/MLTP
Reset

Shield
COM BUS- Shield
RESET/BYP COM

ALERT
B-AC A-AC
DANGER ALERT

(A)

TO
TO

(B)

B-A A-A
B-AO A-AO
B-DC A-DC

DANGER
TO

(B)

B-D A-D
(A)

TO
B-DO A-DO

N L

FUSE
POWER SUPPLY

Accelerometer 220VAC/110VAC
Accelerometer
Velocity Sensor Velocity Sensor

ProvibTech Phone: +1-713-830-7601● Fax: +1-281-754-4972 ● [email protected] ● www.provibtech.com