Bidding Docs

Republic of the Philippines
DEPARTMENT OF PUBLIC WORKS AND HIGHWAYS

SURIGAO DEL SUR II
DISTRICT ENGINEERING OFFICE
REGIONAL OFFICE XIII
Bislig City
BIDDNG DOCUMNTS
FOR
Contract ID No.: 17NI0057 (Re-ad)
Contract Name:
Installation of the Structured Network Cabling and

Electrical Requirements in the new DPWH urigao del Sur
2nd DEO uilding
October 25, 2017 at 8:00 A.M. to 10:00 A.M.

Date of Submission of Bids
October 25, 2017 at 10:00 A.M.

Date of Opening of Bids
TABLE OF CONTENTS
SECTION I. INVITATION TO BIDERROR! BOOKMARK NOT DEFINED.

INVITATION TO BID
SECTION II. INSTRUCTIONS TO BIDDERS3
SECTION III. BID DATA SHEET34
SECTION IV. GENERAL CONDITIONS OF CONTRACT42
SECTION V. SPECIAL CONDITIONS OF CONTRACT78
SECTION VI. SPECIFICATIONS81
SECTION VII. DRAWINGS82
SECTION VIII. BILL OF QUANTITIES83
SECTION IX. BIDDING FORMS88
SECTION X. FOREIGN-ASSISTED PROJECTS
2
epartment of Public Works and Highways (DPWH)
Contract ID: 17NI0057 (Re-ad)
Contract Name: Installation of the Structured Network Cabling and Electrical Requirements
in the new DPWH Surigao del Sur 2nd DEO Building
Location of the Contract: Bislig City, Surigao del Sur

SURIGAO DEL SUR II
DISTRICT ENGINEERING OFFICE
REGIONAL OFFICE XIII
Bislig City
INVITATION TO BID
The Department of Public Works and Highways (DPWH), Surigao del Sur 2nd District
Engineering Office, Bislig City, through its Bids and Awards Committee (BAC), invites
contractors to submit bids for the following Contract:
Contract ID: 17NI0057 (Re-ad)_

Contract Name: Installation of the Structured Network Cabling and Electrical
Requirements in the new DPWH Surigao del Sur 2nd DEO Building
Contract Location: Bislig City, Surigao el Sur
Brief Description: Installation of the Structured Network Cabling and Electrical
Requirements
Approved Budget for the Contract (ABC): PhP _3,782,592.58
Source of Funds: FY 2016 RA 10717 EXTENDED Regular 2016 Continuing
Contract Duration: _120_ calendar days
The BAC is conducting the public Bidding for this contarct in accordance with republic Act No. 9184
and its implementing Rules and Regulation (IRR).
To be eligible to bid for this Contract, a contractor must meet the following major requirements:
(a) Filipino citizen or 75% Filipino-owned partnership/corporation with PCAB license for Size Range
____, (b) completion of a similar contract costing at least 50% of the ABC*, and (c) Net Financial
Contracting Capacity (NFCC) at least equal to ABC.
The DPWH will use non-discretionary “pass/fail” criteria in the eligibilit check, preliminary
examination of bids, evaluation of bids, post qualification, and award.
As stipulated in Section 8.2.4.3 of the Implementing Rules and Regulations of RA 9184, the
PhilGEPS may support the implementing of e-Bid submission processes, which includes creation of
electronic bid forms, creation of bid box, deivery of bid submissions, notification to supplier of
receipt of bids, bid receiving and electronic bid evaluation. This facility shall cover all types of
procurement for goods, infrastructure projects and consulting services
E-Bid submission shall be conducted wherein bidders shall submit their bids electronically through
the PhilGEPS. Manual submission of bids shall not be allowed. This notwithstanding, bidders who
submit e-bids shall be required to sumit hard copies of the documents submitted electronically for
purposes of validation and/or verification during the electronic opening in the event the BAC
encounters technical problems or difficulty in opening e-bids. Fr this purpose, bidders shall register
as Platinum Members in the Government-Official Merchants Registry (OMR). In addition, bidders
who have purchased the Bidding Documents for this project shall be tagged as pilot users of the
e-Bidding.
Registered e-bidding pilot user can download the original copy of the bidding documents including
the electronic bid response form, submit and modify bids online, submit queries online and monitor
the progress of bidding online.
The schedule of key procurement activities for this Contract is shown below:
3
Department of Public Works and Highways (DPWH)

Contract Name: Installation of the Structured Network Cabling and Electrical Requirements
in the new DPWH Surigao del Sur 2nd DEO Building
Location of the Contract: Bislig City, Surigao del Sur
Activity Time Place

1. Issuance/Downloading of September 4, 2017 to Hard copies at BAC Secretariat, DPWH –
Bidding Documents October 25, 2017 Bislig City, Surigao del Sur 2nd District
Engineering Office. Downloadable from
DPWH website www.dpwh.gov.ph,
PhilGEPS website www.philgeps.gov.ph,
and website of concerned foreign Financing
institute
2. Pre-Bid Conference September 12, 2017 at Dpwh-Bislig City, Surigao del Sur 2nd District
10:00 AM Engineering Office at 2nd floor of New
Building at Conference Room.
3. Receipt by the BAC of Deadline: October 25, BAC, Dpwh-Bislig City, Surigao del Sur 2nd
Bids 2017 at 10:00 AM District Engineering Office at 2nd floor of
New Building at Conference Room.
4. Opening of Bids October 25, 2017 at BAC, Dpwh-Bislig City, Surigao del Sur 2nd
10:00 AM District Engineering Office at 2nd floor of
New Building at Conference Room.
Bidders shall pay the BAC a non-refundable fee of ₱ 5,000.00 for the Bidding Documents, upon
securing hard copies of the Documents. Bidders that download the Documents from the DPWH/PhilGPES
website shall pay the fee upon submission of their bids.
The Department of Public Works and Highways (DPWH), Surigao del Sur 2nd District
Engineering Office, Bislig City, reserves the right to accept or reject any bid and to annual the
bidding process any time before the Contract award, without incurring any liability to the affected
bidders, in accordance with the provisions of Section 41 of RA 9184 and its IRR.
Any request for additional information concerning this bidding shall be directed to the following:
CANDELARIO P. PORTILLO GERTRUDES S. CATIIL

OIC- Assistant District Engineer Engineer III
BAC – Chairman Head, BAC Secretariat
Surigao del Sur 2nd District Engineering Office Surigao del Sur 2nd District Engineering Office
Bislig City Bislig City
Telefax (086) 853 – 4308 / Cel # 09291708856 Telefax (086) 853 – 4308/ Cel # 09478933168
Email Address: [email protected]
Approved by:
Dates of Publication: ____N/A______________ CANDELARIO P. PORTILLO

Newspaper: _________N/A________________ OIC- Assistant District Engineer
BAC – Chairman
*For PCAB Small A and Small B Contractors, delete (b) of this paragraph, and rename (c) as (b)
4
Section II. Instructions to Bidders
5
TABLE OF CONTENTS
A. GENERAL ................................................................................. 8
1. Scope of Bid .......................................................................................... 8
2. Source of Funds ..................................................................................... 8
3. Corrupt, Fraudulent, Collusive, and Coercive Practices .............................. 8
4. Conflict of Interest ............................................................................... 10
5. Eligible Bidders .................................................................................... 11
6. Bidder’s Responsibilities........................................................................ 13
7. Origin of GOODS and Services .............................................................. 14
8. Subcontracts........................................................................................ 14
B. CONTENTS OF BIDDING DOCUMENTS ........................................... 15
9. Pre-Bid Conference .............................................................................. 15
10. Clarification and Amendment of Bidding Documents ............................... 15
C. PREPARATION OF BIDS ............................................................. 16
11. Language of Bids ................................................................................. 16
12. Documents Comprising the Bid: Eligibility and Technical Components ..... 16
13. Documents Comprising the Bid: Financial Component ............................ 19
14. Alternative Bids .................................................................................... 19
15. Bid Prices ............................................................................................ 20
16. Bid Currencies ..................................................................................... 20
17. Bid Validity .......................................................................................... 21
18. Bid Security ......................................................................................... 21
19. Format and Signing of Bids ................................................................... 23
20. Sealing and Marking of Bids .................................................................. 24
D. SUBMISSION AND OPENING OF BIDS ........................................... 25
21. Deadline for Submission of Bids ............................................................ 25
22. Late Bids ............................................................................................. 25
23. Modification and Withdrawal of Bids ...................................................... 25
24. Opening and Preliminary Examination of Bids ........................................ 26
E. EVALUATION AND COMPARISON OF BIDS ...................................... 27
25. Process to be Confidential .................................................................... 27
26. Clarification of Bids .............................................................................. 27
6
27. Detailed Evaluation and Comparison of Bids .......................................... 27
28. Post Qualification ................................................................................. 29
29. Reservation Clause ............................................................................... 30
F. AWARD OF CONTRACT .............................................................. 31
30. Contract Award .................................................................................... 31
31. Signing of the Contract ......................................................................... 32
32. Performance Security ........................................................................... 32
33. Notice to Proceed................................................................................. 33
7
A. General
1. Scope of Bid
The Procuring Entity as defined in the BDS, invites bids for the construction of
Works, as described in Section VI. Specifications. The name and
identification number of the Contract is provided in the BDS.
The successful bidder will be expected to complete the Works by the intended
completion date specified in SCC Clause 1.16.
2. Source of Funds
The Procuring Entity has a budget or has applied for or received funds from the
Funding Source named in the BDS, and in the amount indicated in the BDS.
It intends to apply part of the funds received for the Project, as defined in the
BDS, to cover eligible payments under the Contract for the Works.
3. Corrupt, Fraudulent, Collusive, and Coercive Practices

Unless otherwise specified in the BDS, the Procuring Entity, as well as bidders
and contractors, shall observe the highest standard of ethics during the
procurement and execution of the contract. In pursuance of this policy,
the Funding Source:
(a) defines, for purposes of this provision, the terms set forth below
as follows:
(i) "corrupt practice" means behavior on the part of officials

in the public or private sectors by which they improperly
and unlawfully enrich themselves, others, or induce others
to do so, by misusing the position in which they are placed,
and includes the offering, giving, receiving, or soliciting of
anything of value to influence the action of any such official
in the procurement process or in contract execution;
entering, on behalf of the Procuring Entity, into any
contract or transaction manifestly and grossly
disadvantageous to the same, whether or not the public
officer profited or will profit thereby, and similar acts as
provided in Republic Act 3019;
(ii) "fraudulent practice" means a misrepresentation of facts in

order to influence a procurement process or the execution
of a contract to the detriment of the Procuring Entity, and
includes collusive practices among Bidders (prior to or after
Bid submission) designed to establish bid prices at
artificial, non-competitive levels and to deprive the
8
Procuring Entity of the benefits of free and open
competition;
(iii) “collusive practices” means a scheme or arrangement

between two or more bidders, with or without the
knowledge of the Procuring Entity, designed to establish
bid prices at artificial, non-competitive levels; and
(iv) “coercive practices” means harming or threatening to

harm, directly or indirectly, persons, or their property to
influence their participation in a procurement process, or
affect the execution of a contract;
(v) “obstructive practice” is
(aa) deliberately destroying, falsifying, altering or

concealing of evidence material to an
administrative proceedings or investigation or
making false statements to investigators in order
to materially impede an administrative proceedings
or investigation of the Procuring Entity or any
foreign government/foreign or international
financing institution into allegations of a corrupt,
fraudulent, coercive or collusive practice; and/or
threatening, harassing or intimidating any party to
prevent it from disclosing its knowledge of matters
relevant to the administrative proceedings or
investigation or from pursuing such proceedings or
investigation; or
(bb) acts intended to materially impede the exercise of
the inspection and audit rights of the Procuring
Entity or any foreign government/foreign or
international financing institution herein.
(b) will reject a proposal for award if it determines that the bidder
recommended for award has engaged in corrupt or fraudulent
practices in competing for the Contract; and
(c) will declare a firm ineligible, either indefinitely or for a stated

period of time, to be awarded Contract funded by the Funding
Source if it at any time determines that the firm has engaged in
corrupt or fraudulent practices in competing or, or in executing,
a Contract funded by the Funding Source.
Further, the Procuring Entity will seek to impose the maximum civil,
administrative, and/or criminal penalties available under the applicable
laws on individuals and organizations deemed to be involved in any of
the practices mentioned in ITB Clause 3.1(a).
9
Furthermore, the Funding Source and the Procuring Entity reserve the right to
inspect and audit records and accounts of a contractor in the bidding for
and performance of a contract themselves or through independent
auditors as reflected in the GCC Clause 34.
4. Conflict of Interest
All bidders found to have conflicting interests shall be disqualified to participate
in the procurement at hand, without prejudice to the imposition of
appropriate administrative, civil, and criminal sanctions. A Bidder may
be considered to have conflicting interests with another Bidder in any of
the events described in paragraphs (a) through (c) and a general conflict
of interest in any of the circumstances set out in paragraphs (d) through
(g) below:
(a) A Bidder has controlling shareholders in common with another

Bidder;
(b) A Bidder receives or has received any direct or indirect subsidy

from any other Bidder;
(c) A Bidder has the same legal representative as that of another

Bidder for purposes of this Bid;
(d) A Bidder has a relationship, directly or through third parties, that

puts them in a position to have access to information about or
influence on the bid of another Bidder or influence the decisions
of the Procuring Entity regarding this bidding process. This will
include a firm or an organization who lends, or temporarily
seconds, its personnel to firms or organizations which are
engaged in consulting services for the preparation related to
procurement for or implementation of the project if the personnel
would be involved in any capacity on the same project;
(e) A Bidder submits more than one bid in this bidding process.
However, this does not limit the participation of subcontractors in
more than one bid;
(f) A Bidder who participated as a consultant in the preparation of

the design or technical specifications of the goods and related
services that are the subject of the bid; or
(g) A Bidder who lends, or temporary seconds, its personnel to firms

or organizations which are engaged in consulting services for the
preparation related to procurement for or implementation of the
project, if the personnel would be involved in any capacity on the
same project.
10
In accordance with Section 47 of the IRR of RA 9184, all Bidding Documents
shall be accompanied by a sworn affidavit of the Bidder that it is not
related to the Head of the Procuring Entity, members of the Bids and
Awards Committee (BAC), members of the Technical Working Group
(TWG), members of the BAC Secretariat, the head of the Project
Management Office (PMO) or the end-user unit, and the project
consultants, by consanguinity or affinity up to the third civil degree. On
the part of the bidder, this Clause shall apply to the following persons:
(h) If the Bidder is an individual or a sole proprietorship, to the Bidder

himself;
(i) If the Bidder is a partnership, to all its officers and members;
(j) If the Bidder is a corporation, to all its officers, directors, and

controlling stockholders; and
(k) If the Bidder is a joint venture (JV), the provisions of items (a),
(b), or (c) of this Clause shall correspondingly apply to each of
the members of the said JV, as may be appropriate.
Relationship of the nature described above or failure to comply with this

Clause will result in the automatic disqualification of a Bidder.
5. Eligible Bidders
Unless otherwise indicated in the BDS, the following persons shall be eligible to
participate in this Bidding:
(a) Duly licensed Filipino citizens/sole proprietorships;
(b) Partnerships duly organized under the laws of the Philippines and
of which at least seventy five percent (75%) of the interest
belongs to citizens of the Philippines;
(c) Corporations duly organized under the laws of the Philippines,

and of which at least seventy five percent (75%) of the
outstanding capital stock belongs to citizens of the Philippines;
(d) Cooperatives duly organized under the laws of the Philippines,

and of which at least seventy five percent (75%) of the interest
belongs to citizens of the Philippines; and
(e) Persons/entities forming themselves into a JV, i.e., a group of two

(2) or more persons/entities that intend to be jointly and severally
responsible or liable for a particular contract: Provided, however,
that, in accordance with Letter of Instructions No. 630, Filipino
ownership or interest of the joint venture concerned shall be at
least seventy five percent (75%): Provided, further, that joint
ventures in which Filipino ownership or interest is less than
11
seventy five percent (75%) may be eligible where the structures
to be built require the application of techniques and/or
technologies which are not adequately possessed by a
person/entity meeting the seventy five percent (75%) Filipino
ownership requirement: Provided, finally, that in the latter case,
Filipino ownership or interest shall not be less than twenty five
percent (25%). For this purpose Filipino ownership or interest
shall be based on the contributions of each of the members of the
joint venture as specified in their JVA.
The Procuring Entity may also invite foreign bidders when provided for under
any Treaty or International or Executive Agreement as specified in the
BDS.
Government Corporate Entities may be eligible to participate only if they can

establish that they (a) are legally and financially autonomous, (b)
operate under commercial law, and (c) are not dependent agencies of
the GOP or the Procuring Entity.
(a) Unless otherwise provided in the BDS, the Bidder must have completed,
within ten (10) years from the submission of bids, a single contract that
is similar to this Project, equivalent to at least fifty percent (50%) of the
ABC adjusted to current prices using the National Statistics Office
consumer price index.
(b) For Foreign-funded Procurement, the Procuring Entity and the

foreign government/foreign or international financing institution may
agree on another track record requirement, as specified in the BDS.
For this purpose, contracts similar to the Project shall be those described
in the BDS, and completed within the period stated in the Invitation to
Bid and ITB Clause 12(a)(iii).
The Bidder must submit a computation of its Net Financial

Contracting Capacity (NFCC), which must be at least equal to
the ABC to be bid, calculated as follows:
NFCC = [(Current assets minus current liabilities) (K)] minus the

value of all outstanding or uncompleted portions of the projects
under ongoing contracts, including awarded contracts yet to be
started coinciding with the contract to be bid.
Where: K = 10 for a contract duration of one year or less, 15 for a
contract duration of more than one year up to two years, and 20
for a contract duration of more than two years.
The values of the bidder’s current assets and current
liabilities shall be based on the data submitted to the BIR,
through its Electronic Filing and Payment System (EFPS).
12
6. Bidder’s Responsibilities
The Bidder or its duly authorized representative shall submit a sworn statement
in the form prescribed in Section IX. Bidding Forms as required in ITB
Clause 12(b)(iii).
The Bidder is responsible for the following:
(a) Having taken steps to carefully examine all of the Bidding

Documents;
(b) Having acknowledged all conditions, local or otherwise, affecting

the implementation of the contract;
(c) Having made an estimate of the facilities available and needed

for the contract to be bid, if any;
(d) Having complied with its responsibility to inquire or secure

Supplemental/Bid Bulletin/s as provided under ITB Clause 0.
(e) Ensuring that it is not “blacklisted” or barred from bidding by the

GOP or any of its agencies, offices, corporations, or LGUs,
including foreign government/foreign or international financing
institution whose blacklisting rules have been recognized by the
GPPB;
(f) Ensuring that each of the documents submitted in satisfaction of

the bidding requirements is an authentic copy of the original,
complete, and all statements and information provided
therein are true and correct;
(g) Authorizing the Head of the Procuring Entity or its duly authorized
representative/s to verify all the documents submitted;
(h) Ensuring that the signatory is the duly authorized representative

of the Bidder, and granted full power and authority to do, execute
and perform any and all acts necessary and/or to represent the
Bidder in the bidding, with the duly notarized Secretary’s
Certificate attesting to such fact, if the Bidder is a corporation,
partnership, cooperative, or joint venture;
(i) Complying with the disclosure provision under Section 47 of the

Act in relation to other provisions of Republic Act 3019; and
(j) Complying with existing labor laws and standards, if applicable.
Failure to observe any of the above responsibilities shall be at the risk

of the Bidder concerned.
13
The Bidder, by the act of submitting its bid, shall be deemed to have inspected
the site, determined the general characteristics of the contract works
and the conditions for this Project and examine all instructions, forms,
terms, and project requirements in the Bidding Documents.
It shall be the sole responsibility of the prospective bidder to determine and to

satisfy itself by such means as it considers necessary or desirable as to
all matters pertaining to this Project, including: (a) the location and the
nature of the contract, project, or work; (b) climatic conditions; (c)
transportation facilities; (c) nature and condition of the terrain,
geological conditions at the site communication facilities, requirements,
location and availability of construction aggregates and other materials,
labor, water, electric power and access roads; and (d) other factors that
may affect the cost, duration and execution or implementation of the
contract, project, or work.
The Procuring Entity shall not assume any responsibility regarding erroneous
interpretations or conclusions by the prospective or eligible bidder out of
the data furnished by the procuring entity.
Before submitting their bids, the Bidders are deemed to have become familiar
with all existing laws, decrees, ordinances, acts and regulations of the
Philippines which may affect the contract in any way.
The Bidder shall bear all costs associated with the preparation and submission
of his bid, and the Procuring Entity will in no case be responsible or liable
for those costs, regardless of the conduct or outcome of the bidding
process.
Bidders should note that the Procuring Entity will only accept bids only from
those that have paid the nonrefundable fee for the Bidding Documents
at the office indicated in the Invitation to Bid.
7. Origin of GOODS and Services

There is no restriction on the origin of Goods, or Contracting of Works or
Services other than those prohibited by a decision of the United Nations
Security Council taken under Chapter VII of the Charter of the United Nations.
8. Subcontracts
Unless otherwise specified in the BDS, the Bidder may subcontract portions of
the Works to an extent as may be approved by the Procuring Entity and
stated in the BDS. However, subcontracting of any portion shall not
relieve the Bidder from any liability or obligation that may arise from the
contract for this Project.
Subcontractors must submit the documentary requirements under ITB Clause

12 and comply with the eligibility criteria specified in the BDS. In the
14
event that any subcontractor is found by the Procuring Entity to be
ineligible, the subcontracting of such portion of the Works shall be
disallowed.
The Bidder may identify the subcontractor to whom a portion of the Works will
be subcontracted at any stage of the bidding process or during contract
implementation. If the Bidder opts to disclose the name of the
subcontractor during bid submission, the Bidder shall include the
required documents as part of the technical component of its bid.
B. Contents of Bidding Documents
9. Pre-Bid Conference
(a) If so specified in the BDS, a pre-bid conference shall be held at the venue
and on the date indicated therein, to clarify and address the Bidders’
questions on the technical and financial components of this Project.
(b) The pre-bid conference shall be held at least twelve (12) calendar
days before the deadline for the submission of and receipt of bids. If
the Procuring Entity determines that, by reason of the method, nature,
or complexity of the contract to be bid, or when international
participation will be more advantageous to the GOP, a longer period for
the preparation of bids is necessary, the pre-bid conference shall be
held at least thirty (30) calendar days before the deadline for the
submission and receipt of bids, as specified in the BDS.
Bidders are encouraged to attend the pre-bid conference to ensure that they
fully understand the Procuring Entity’s requirements. Non-attendance
of the Bidder will in no way prejudice its bid; however, the Bidder is
expected to know the changes and/or amendments to the Bidding
Documents as recorded in the minutes of the pre-bid conference and
the Supplemental/Bid Bulletin.
Any statement made at the pre-bid conference shall not modify the terms of
the bidding documents unless such statement is specifically identified in
writing as an amendment thereto and issued as a Supplemental/Bid
Bulletin.
10. Clarification and Amendment of Bidding Documents

Bidders who have purchased the Bidding Documents may request for
clarification(s) on any part of the Bidding Documents or for an
interpretation. Such a request must be in writing and submitted to the
Procuring Entity at the address indicated in the BDS at least ten (10)
calendar days before the deadline set for the submission and receipt of
Bids.
15
Supplemental/Bid Bulletins may be issued upon the Procuring Entity’s initiative
for purposes of clarifying or modifying any provision of the Bidding
Documents not later than seven (7) calendar days before the deadline
for the submission and receipt of Bids. Any modification to the Bidding
Documents shall be identified as an amendment.
Any Supplemental/Bid Bulletin issued by the BAC shall also be posted on the
Philippine Government Electronic Procurement System (PhilGEPS) and
the website of the Procuring Entity concerned, if available. Unless,
otherwise provided in the BDS, it shall be the responsibility of all Bidders
who secure the Bidding Documents to inquire and secure
Supplemental/Bid Bulletins that may be issued by the BAC. However,
bidders who have submitted bids before the issuance of the
Supplemental/Bid Bulletin must be informed and allowed to modify or
withdraw their bids in accordance with ITB Clause23.
C. Preparation of Bids
11. Language of Bids

The Bid, as well as all correspondence and documents relating to the Bid
exchanged by the Bidder and the Procuring Entity, shall be written in English.
Supporting documents and printed literature furnished by the Bidder may be in
another language provided they are accompanied by an accurate translation in
English certified by the appropriate embassy or consulate in the Philippines, in
which case the English translation shall govern, for purposes of interpretation
of the Bid.
12. Documents Comprising the Bid: Eligibility and Technical

Components
Unless otherwise indicated in the BDS, the first envelope shall contain the
following eligibility and technical documents:
(a) Eligibility Documents –
Class "A" Documents:
(i) Registration certificate from the Securities and Exchange

Commission (SEC), Department of Trade and Industry
(DTI) for sole proprietorship, or Cooperative Development
Authority (CDA) for cooperatives, or any proof of such
registration as stated in the BDS;
(ii) Mayor’s permit issued by the city or municipality where the

principal place of business of the prospective bidder is
located;
16
(iii) Statement of all its ongoing and completed government
and private contracts within ten (10) years from the
submission of bids, including contracts awarded but not
yet started, if any. The statement shall include, for each
contract, the following:
(iii.1) name of the contract;
(iii.2) date of the contract;
(iii.3) contract duration;
(iii.4) owner’s name and address;
(iii.5) nature of work;
(iii.6) contractor’s role (whether sole contractor,

subcontractor, or partner in a JV) and percentage
of participation;
(iii.7) total contract value at award;
(iii.8) date of completion or estimated completion time;
(iii.9) total contract value at completion, if applicable;
(iii.10) percentages of planned and actual

accomplishments, if applicable;
(iii.11) value of outstanding works, if applicable;
(iii.12) the statement shall be supported by the notices of

award and/or notices to proceed issued by the
owners; and
(iii.13) the statement shall be supported by the

Constructors Performance Evaluation System
(CPES) rating sheets, and/or certificates of
completion and owner’s acceptance, if applicable;
(iv) Unless otherwise provided in the BDS, valid Philippine

Contractors Accreditation Board (PCAB) license and
registration for the type and cost of the contract for this
Project;
(v) Audited financial statements, showing, among others, the

prospective total and current assets and liabilities,
stamped “received” by the BIR or its duly accredited and
authorized institutions, for the preceding calendar year
17
which should not be earlier than two (2) years from the
date of bid submission;
(vi) NFCC computation or CLC in accordance with ITB Clause

0; and
Class "B" Document:
(vii) If applicable, valid Joint Venture Agreement (JVA) or, in

lieu thereof, duly notarized statements from all the
potential joint venture partners stating that they will enter
into and abide by the provisions of the JVA in the instance
that the bid is successful shall be included in the bid.
(b) Technical Documents –
(i) Bid security as prescribed in ITB Clause 18. If the Bidder

Procuring Entity requires the Bidders to submit the bid
security in the form of:
(i.1) a bank draft/guarantee or an irrevocable letter of

credit issued by a foreign bank, it shall be
accompanied by a confirmation from a Universal or
Commercial Bank; or
(i.2) a surety bond accompanied by a certification

coming from an authorized Insurance Commission
that a surety or insurance company is authorized to
issue such instrument;
(ii) Project Requirements, which shall include the following:
(ii.1) Organizational chart for the contract to be bid;
(ii.2) List of contractor’s personnel (viz, project Manager,

Project Engineers, Materials Engineers, and
Foremen), to be assigned to the contract to be bid,
with their complete qualification and experience
data; and
(ii.3) List of contractor’s equipment units, which are

owned, leased, and/or under purchase agreements,
supported by certification of availability of
equipment from the equipment lessor/vendor for
the duration of the project; and
(iii) Sworn statement in accordance with Section 25.2(b)(iv) of

the IRR of RA 9184 and using the form prescribed in
Section IX. Bidding Forms.
18
13. Documents Comprising the Bid: Financial Component
Unless otherwise stated in the BDS, the financial component of the bid shall
contain the following:
(a) Financial Bid Form in accordance with the form prescribed in

Forms; and
(b) Any other document related to the financial component of the bid
as stated in the BDS.
(a) Unless indicated in the BDS, all Bids that exceed the ABC shall not be
accepted.
(b) Unless otherwise indicated in the BDS, for foreign-funded

procurement, a ceiling may be applied to bid prices provided the
following conditions are met:
(i) Bidding Documents are obtainable free of charge on a freely

accessible website. If payment of Bidding Documents is
required by the procuring entity, payment could be made
upon the submission of bids.
(ii) The procuring entity has procedures in place to ensure that
the ABC is based on recent estimates made by the
engineer or the responsible unit of the procuring entity and
that the estimates are based on adequate detailed
engineering (in the case of works) and reflect the quality,
supervision and risk and inflationary factors, as well as
prevailing market prices, associated with the types of
works or goods to be procured.
(iii) The procuring entity has trained cost estimators on
estimating prices and analyzing bid variances. In the case
of infrastructure projects, the procuring entity must also
have trained quantity surveyors.
(iv) The procuring entity has established a system to monitor
and report bid prices relative to ABC and
engineer’s/procuring entity’s estimate.
(v) The procuring entity has established a monitoring and
evaluation system for contract implementation to provide a
feedback on actual total costs of goods and works.
14. Alternative Bids

Alternative Bids shall be rejected. For this purpose, alternative bid is an offer
made by a Bidder in addition or as a substitute to its original bid which
may be included as part of its original bid or submitted separately
therewith for purposes of bidding. A bid with options is considered an
alternative bid regardless of whether said bid proposal is contained in a
single envelope or submitted in two (2) or more separate bid envelopes.
19
Bidders shall submit offers that comply with the requirements of the Bidding
Documents, including the basic technical design as indicated in the
drawings and specifications. Unless there is a value engineering clause
in the BDS, alternative bids shall not be accepted.
Each Bidder shall submit only one Bid, either individually or as a partner in a
JV. A Bidder who submits or participates in more than one bid (other
than as a subcontractor if a subcontractor is permitted to participate in
more than one bid) will cause all the proposals with the Bidder’s
participation to be disqualified. This shall be without prejudice to any
applicable criminal, civil and administrative penalties that may be
imposed upon the persons and entities concerned.
15. Bid Prices

The contract shall be for the whole Works, as described in ITB Clause 0, based
on the priced Bill of Quantities submitted by the Bidder.
The Bidder shall fill in rates and prices for all items of the Works described in
the Bill of Quantities. Bids not addressing or providing all of the required
items in the Bidding Documents including, where applicable, bill of
quantities, shall be considered non-responsive and, thus, automatically
disqualified. In this regard, where a required item is provided, but no
price is indicated, the same shall be considered as non-responsive, but
specifying a "0" (zero) for the said item would mean that it is being
offered for free to the Government.
All duties, taxes, and other levies payable by the Contractor under the Contract,
or for any other cause, prior to the deadline for submission of bids, shall
be included in the rates, prices, and total bid price submitted by the
Bidder.
All bid prices for the given scope of work in the contract as awarded shall be
considered as fixed prices, and therefore not subject to price escalation
during contract implementation, except under extraordinary
circumstances as specified in GCC Clause 48.Price escalation may be
allowed in extraordinary circumstances as may be determined by the
National Economic and Development Authority in accordance with the
Civil Code of the Philippines, and upon the recommendation of the
Procuring Entity. Furthermore, in cases where the cost of the awarded
contract is affected by any applicable new laws, ordinances, regulations,
or other acts of the GOP, promulgated after the date of bid opening, a
contract price adjustment shall be made or appropriate relief shall be
applied on a no loss-no gain basis.
16. Bid Currencies

All bid prices shall be quoted in Philippine Pesos unless otherwise provided in
the BDS. However, for purposes of bid evaluation, bids denominated in
20
foreign currencies shall be converted to Philippine currency based on the
exchange rate prevailing on the day of the Bid opening.
If so allowed in accordance with ITB Clause 0, the Procuring Entity for purposes
of bid evaluation and comparing the bid prices will convert the amounts
in various currencies in which the bid price is expressed to Philippine
Pesos at the exchange rate as published in the BSP reference rate
bulletin on the day of the bid opening.
Unless otherwise specified in the BDS, payment of the contract price shall be
made in Philippine Pesos.
17. Bid Validity

Bids shall remain valid for the period specified in the BDS which shall not
exceed one hundred twenty (120) calendar days from the date of the
opening of bids.
In exceptional circumstances, prior to the expiration of the bid validity period,

the Procuring Entity may request Bidders to extend the period of validity
of their bids. The request and the responses shall be made in writing.
The bid security described in ITB Clause 18 should also be extended
corresponding to the extension of the bid validity period at the least. A
Bidder may refuse the request without forfeiting its bid security, but his
bid shall no longer be considered for further evaluation and award. A
Bidder granting the request shall not be required or permitted to modify
its bid.
18. Bid Security

The bidders may opt to use, which shall include the Bid Securing Declaration
provided in Section 27.5 of the IRR and at least one (1) other form, the
amount of which shall be equal to a percentage of the ABC in accordance
with the following schedule:
Amount of Bid Security

Form of Bid Security (Equal to Percentage of the
ABC)
(a) Cash or cashiers’/manager’s
check issued by a Universal or
Commercial Bank.
(b.) bank draft/guarantee or
irrevocable letter of credit issued by
Two percent (2%)
a Universal or Commercial Bank:
Provided, however, that it shall be
confirmed or authenticated by a
Universal or Commercial Bank, if
issued by a foreign bank.
21
(c.) Surety bond callable upon
demand issued by a surety or Five percent (5%)
insurance company duly certified by
the Insurance Commission as
authorized to issue such security
(d.) Any combination of the Proportionate to share of form

foregoing with respect to the total
amount of security
For biddings conducted by LGUs, the procuring entity may also require
bidders to submit bid securities in the form of cashier’s/manager’s check,
bank draft/guarantee, or irrevocable letter of credit from other banks
certified by the BSP as authorized to issue such financial statement.
The bid security should be valid for the period specified in the BDS. Any bid
not accompanied by an acceptable bid security shall be rejected by the
Procuring Entity as non-responsive.
No bid securities shall be returned to bidders after the opening of bids and
before contract signing, except to those that failed or declared as post-
disqualified, upon submission of a written waiver of their right to file a
motion for reconsideration and/or protest. Without prejudice on its
forfeiture, Bid Securities shall be returned only after the bidder with the
Lowest Calculated Responsive Bid has signed the contract and furnished
the Performance Security, but in no case later than the expiration of the
Bid Security validity period indicated in ITB Clause 0.
Upon signing and execution of the contract, pursuant to ITB Clause 31, and
the posting of the performance security, pursuant to ITB Clause 32, the
successful Bidder’s Bid security will be discharged, but in no case later
than the Bid security validity period as indicated in ITB Clause 0.
The bid security may be forfeited:
(a) if a Bidder:
(i) withdraws its bid during the period of bid validity specified
in ITB Clause 17;
(ii) does not accept the correction of errors pursuant to ITB

Clause 27(d);
(iii) fails to submit the requirements within the prescribed

period, or a finding against their veracity, as stated in ITB
Clause 0;
22
(iv) submission of eligibility requirements containing false
information or falsified documents;
(v) submission of bids that contain false information or

falsified documents, or the concealment of such
information in the bids in order to influence the outcome
of eligibility screening or any other stage of the public
bidding;
(vi) allowing the use of one’s name, or using the name of

another for purposes of public bidding;
(vii) withdrawal of a bid, or refusal to accept an award, or enter

into contract with the Government without justifiable
cause, after the Bidder had been adjudged as having
submitted the Lowest Calculated and Responsive Bid;
(viii) refusal or failure to post the required performance security

within the prescribed time;
(ix) refusal to clarify or validate in writing its bid during post-

qualification within a period of seven (7) calendar days
from receipt of the request for clarification;
(x) any documented attempt by a bidder to unduly influence

the outcome of the bidding in his favor;
(xi) failure of the potential joint venture partners to enter into

the joint venture after the bid is declared successful; or
(xii) all other acts that tend to defeat the purpose of the
competitive bidding, such as habitually withdrawing from
bidding, submitting late Bids or patently insufficient bid, for
at least three (3) times within a year, except for valid
reasons.
(b) if the successful Bidder:
(i) fails to sign the contract in accordance with ITB Clause31;
(ii) fails to furnish performance security in accordance with

ITBClause32.
19. Format and Signing of Bids

Bidders shall submit their bids through their duly authorized representative
using the appropriate forms provided in Section IX. Bidding Forms on or
before the deadline specified in the ITB Clause 21 in two (2) separate
sealed bid envelopes, and which shall be submitted simultaneously. The
first shall contain the technical component of the bid, including the
23
eligibility requirements under ITB Clause 0, and the second shall contain
the financial component of the bid.
Forms as mentioned in ITB Clause 0 must be completed without any alterations

to their format, and no substitute form shall be accepted. All blank
spaces shall be filled in with the information requested.
The Bidder shall prepare an original of the first and second envelopes as
described in ITB Clauses 12 and 13.
The bid, except for unamended printed literature, shall be signed, and each
and every page thereof shall be initialed, by the duly authorized
representative/s of the Bidder.
Any interlineations, erasures, or overwriting shall be valid only if they are signed
or initialed by the duly authorized representative/s of the Bidder.
20. Sealing and Marking of Bids

Bidders shall enclose their original eligibility and technical documents described
in ITB Clause 12, in one sealed envelope marked “ORIGINAL -
TECHNICAL COMPONENT”, and the original of their financial component
in another sealed envelope marked “ORIGINAL - FINANCIAL
COMPONENT”, sealing them all in an outer envelope marked “ORIGINAL
BID”.
Each copy of the first and second envelopes shall be similarly sealed duly
marking the inner envelopes as “COPY NO. ___ - TECHNICAL
COMPONENT” and “COPY NO. ___ – FINANCIAL COMPONENT” and the
outer envelope as “COPY NO. ___”, respectively. These envelopes
containing the original and the copies shall then be enclosed in one
single envelope.
The original and the number of copies of the Bid as indicated in the BDS shall
be typed or written in indelible ink and shall be signed by the bidder or
its duly authorized representative/s.
All envelopes shall:
(a) contain the name of the contract to be bid in capital letters;
(b) bear the name and address of the Bidder in capital letters;
(c) be addressed to the Procuring Entity’s BAC identified in ITB

Clause 0;
(d) bear the specific identification of this bidding process indicated in

the Invitation to Bid; and
24
(e) bear a warning “DO NOT OPEN BEFORE…” the date and time for
the opening of bids, in accordance with ITB Clause 21.
(e)(f) shall be book binded with index tab of each of the documents
required in the checklist.
If bids are not sealed and marked as required, the Procuring Entity will assume
no responsibility for the misplacement or premature opening of the bid.
D. Submission and Opening of Bids
21. Deadline for Submission of Bids

Bids must be received by the Procuring Entity’s BAC at the address and on or
before the date and time indicated in the BDS.
22. Late Bids

Any bid submitted after the deadline for submission and receipt of bids
prescribed by the Procuring Entity, pursuant to ITB Clause 21, shall be
declared “Late” and shall not be accepted by the Procuring Entity.
23. Modification and Withdrawal of Bids

The Bidder may modify its bid after it has been submitted; provided that the
modification is received by the Procuring Entity prior to the deadline
prescribed for submission and receipt of bids. The Bidder shall not be
allowed to retrieve its original bid, but shall be allowed to submit another
bid equally sealed, properly identified, linked to its original bid marked
as “TECHNICAL MODIFICATION” or “FINANCIAL MODIFICATION” and
stamped “received” by the BAC. Bid modifications received after the
applicable deadline shall not be considered and shall be returned to the
Bidder unopened.
A Bidder may, through a letter of withdrawal, withdraw its bid after it has been
submitted, for valid and justifiable reason; provided that the letter of
withdrawal is received by the Procuring Entity prior to the deadline
prescribed for submission and receipt of bids.
Bids requested to be withdrawn in accordance with ITB Clause 0 shall be

returned unopened to the Bidders. A Bidder may also express its
intention not to participate in the bidding through a letter which should
reach and be stamped by the BAC before the deadline for submission
and receipt of bids. A Bidder that withdraws its bid shall not be permitted
to submit another bid, directly or indirectly, for the same contract.
No bid may be modified after the deadline for submission of bids. No bid may
be withdrawn in the interval between the deadline for submission of bids
and the expiration of the period of bid validity specified by the Bidder on
25
the Financial Bid Form. Withdrawal of a bid during this interval shall
result in the forfeiture of the Bidder’s bid security, pursuant to ITB
Clause 0, and the imposition of administrative, civil, and criminal
sanctions as prescribed by RA 9184 and its IRR.
24. Opening and Preliminary Examination of Bids

The BAC shall open the first bid envelopes of Bidders in public as specified in
the BDS to determine each Bidder’s compliance with the documents
prescribed in ITB Clause 12. For this purpose, the BAC shall check the
submitted documents of each bidder against a checklist of required
documents to ascertain if they are all present, using a non-discretionary
“pass/fail” criterion. If a bidder submits the required document, it shall
be rated “passed” for that particular requirement. In this regard, bids
that fail to include any requirement or are incomplete or patently
insufficient shall be considered as “failed”. Otherwise, the BAC shall rate
the said first bid envelope as “passed”.
Unless otherwise specified in the BDS, immediately after determining

compliance with the requirements in the first envelope, the BAC shall
forthwith open the second bid envelope of each remaining eligible bidder
whose first bid envelope was rated “passed”. The second envelope of
each complying bidder shall be opened within the same day. In case one
or more of the requirements in the second envelope of a particular bid
is missing, incomplete or patently insufficient, and/or if the submitted
total bid price exceeds the ABC unless otherwise provided in ITB Clause
13(b), the BAC shall rate the bid concerned as “failed”. Only bids that
are determined to contain all the bid requirements for both components
shall be rated “passed” and shall immediately be considered for
evaluation and comparison.
Letters of withdrawal shall be read out and recorded during bid opening, and
the envelope containing the corresponding withdrawn bid shall be
returned to the Bidder unopened. If the withdrawing Bidder’s
representative is in attendance, the original bid and all copies thereof
shall be returned to the representative during the bid opening. If the
representative is not in attendance, the Bid shall be returned unopened
by registered mail. The Bidder may withdraw its bid prior to the deadline
for the submission and receipt of bids, provided that the corresponding
letter of withdrawal contains a valid authorization requesting for such
withdrawal, subject to appropriate administrative sanctions.
If a Bidder has previously secured a certification from the Procuring Entity to

the effect that it has previously submitted the above-enumerated Class
“A” Documents, the said certification may be submitted in lieu of the
requirements enumerated in ITB Clause 12(a), items (i) to (vi).
In the case of an eligible foreign Bidder as described in ITB Clause 5, the Class
“A” Documents enumerated in ITB Clause 12(a)may be substituted with
26
the appropriate equivalent documents, if any, issued by the country of
the foreign Bidder concerned.
Each partner of a joint venture agreement shall likewise submit the documents
required in ITB Clauses 12(a)(i) and 12(a)(ii). Submission of documents
required under ITB Clauses 12(a)(iii) to 12(a)(vi)by any of the joint
venture partners constitutes compliance.
A Bidder determined as “failed” has three (3) calendar days upon written notice
or, if present at the time of bid opening, upon verbal notification within
which to file a request for reconsideration with the BAC: Provided,
however, that the request for reconsideration shall not be granted if it is
established that the finding of failure is due to the fault of the Bidder
concerned: Provided, further, that the BAC shall decide on the request
for reconsideration within seven (7) calendar days from receipt thereof.
If a failed Bidder signifies his intent to file a request for reconsideration,
the BAC shall keep the bid envelopes of the said failed Bidder unopened
and/or duly sealed until such time that the request for reconsideration
or protest has been resolved.
E. Evaluation and Comparison of Bids
25. Process to be Confidential

Members of the BAC, including its staff and personnel, as well as its Secretariat
and TWG, are prohibited from making or accepting any kind of
communication with any bidder regarding the evaluation of their bids
until the issuance of the Notice of Award, unless n the case of ITB Clause
26.
Any effort by a bidder to influence the Procuring Entity in the Procuring Entity’s
decision in respect of Bid evaluation, Bid comparison or contract award
will result in the rejection of the Bidder’s Bid.
26. Clarification of Bids

To assist in the evaluation, comparison and post-qualification of the bids, the
Procuring Entity may ask in writing any Bidder for a clarification of its bid. All
responses to requests for clarification shall be in writing. Any clarification
submitted by a Bidder in respect to its bid and that is not in response to a
request by the Procuring Entity shall not be considered
27. Detailed Evaluation and Comparison of Bids

The Procuring Entity will undertake the detailed evaluation and comparison of
Bids which have passed the opening and preliminary examination of
Bids, pursuant to ITB Clause 24, in order to determine the Lowest
Calculated Bid.
27
In evaluating the Bids to get the Lowest Calculated Bid, the Procuring Entity
shall undertake the following:
(a) The detailed evaluation of the financial component of the bids, to

establish the correct calculated prices of the bids; and
(b) The ranking of the total bid prices as so calculated from the lowest
to highest. The bid with the lowest price shall be identified as the
Lowest Calculated Bid.
The Procuring Entity's BAC shall immediately conduct a detailed evaluation of

all bids rated “passed,” using non-discretionary “pass/fail” criterion. The
BAC shall consider the following in the evaluation of bids:
(c) Completeness of the bid. Unless the ITB specifically allows partial
bids, bids not addressing or providing all of the required items in
the Schedule of Requirements including, where applicable, bill of
quantities, shall be considered non-responsive and, thus,
automatically disqualified. In this regard, where a required item
is provided, but no price is indicated, the same shall be considered
as non-responsive, but specifying a "0" (zero) for the said item
would mean that it is being offered for free to the Procuring
Entity; and
(d) Arithmetical corrections. Consider computational errors and

omissions to enable proper comparison of all eligible bids. It may
also consider bid modifications if expressly allowed in the BDS.
Any adjustment shall be calculated in monetary terms to
determine the calculated prices.
Based on the detailed evaluation of bids, those that comply with the above-
mentioned requirements shall be ranked in the ascending order of their
total calculated bid prices, as evaluated and corrected for computational
errors, discounts and other modifications, to identify the Lowest
Calculated Bid. Total calculated bid prices, as evaluated and corrected
for computational errors, discounts and other modifications, which
exceed the ABC shall not be considered, unless otherwise indicated in
the BDS.
The Procuring Entity’s evaluation of bids shall only be based on the bid price
quoted in the Financial Bid Form
Bids shall be evaluated on an equal footing to ensure fair competition. For this
purpose, all bidders shall be required to include in their bids the cost of
all taxes, such as, but not limited to, value added tax (VAT), income tax,
local taxes, and other fiscal levies and duties which shall be itemized in
the bid form and reflected in the detailed estimates. Such bids, including
said taxes, shall be the basis for bid evaluation and comparison.
28
28. Post Qualification
The Procuring Entity shall determine to its satisfaction whether the Bidder that
is evaluated as having submitted the Lowest Calculated Bid (LCB)
complies with and is responsive to all the requirements and conditions
specified in ITB Clauses 5, 12, and 13.
Within a non-extendible period of three (3) calendar days from receipt by the
Bidder of the notice from the BAC that it submitted the LCB, the Bidder
shall submit the following documentary requirements:
(a) Tax clearance per Executive Order 398, Series of 2005;as finally
reviewed and approved by the BIR
(b) Latest income and business tax returns in the form specified in
the BDS;
(c) Certificate of PhilGEPS Registration; and
(d) Other appropriate licenses and permits required by law and stated
in the BDS.
Failure of the Bidder declared as LCB to duly submit the requirements

under this Clause or a finding against the veracity of such shall be
ground for forfeiture of the bid security and disqualification of the
Bidder for award.
The determination shall be based upon an examination of the documentary

evidence of the Bidder’s qualifications submitted pursuant to ITB
Clauses 12and 13, as well as other information as the Procuring Entity
deems necessary and appropriate, using a non-discretionary “pass/fail”
criterion.
If the BAC determines that the Bidder with the Lowest Calculated Bid passes all
the criteria for post-qualification, it shall declare the said bid as the
Lowest Calculated Responsive Bid, and recommend to the Head of the
Procuring Entity the award of contract to the said Bidder at its submitted
price or its calculated bid price, whichever is lower, subject to ITB Clause
0.
A negative determination shall result in rejection of the Bidder’s Bid, in which

event the Procuring Entity shall proceed to the next Lowest Calculated
Bid to make a similar determination of that Bidder’s capabilities to
perform satisfactorily. If the second Bidder, however, fails the post
qualification, the procedure for post qualification shall be repeated for
the Bidder with the next Lowest Calculated Bid, and so on until the
Lowest Calculated and Responsive Bid is determined for contract award.
29
Within a period not exceeding seven (7) calendar days from the date of receipt
of the recommendation of the BAC, the Head of the Procuring Entity
shall approve or disapprove the said recommendation. In the case of
government owned and government-owned and/or -controlled
corporations (GOCCs) and government financial institutions (GFIs), the
period provided herein shall be fifteen (15) calendar days.
29. Reservation Clause

Notwithstanding the eligibility or post-qualification of a bidder, the Procuring
Entity concerned reserves the right to review its qualifications at any
stage of the procurement process if it has reasonable grounds to believe
that a misrepresentation has been made by the said bidder, or that there
has been a change in the Bidder’s capability to undertake the project
from the time it submitted its eligibility requirements. Should such
review uncover any misrepresentation made in the eligibility and bidding
requirements, statements or documents, or any changes in the situation
of the Bidder which will affect its capability to undertake the project so
that it fails the preset eligibility or bid evaluation criteria, the Procuring
Entity shall consider the said Bidder as ineligible and shall disqualify it
from submitting a bid or from obtaining an award or contract.
Based on the following grounds, the Procuring Entity reserves the right to reject
any and all Bids, declare a Failure of Bidding at any time prior to the
contract award, or not to award the contract, without thereby incurring
any liability, and make no assurance that a contract shall be entered into
as a result of the bidding:
(a) if there is prima facie evidence of collusion between appropriate

public officers or employees of the Procuring Entity, or between
the BAC and any of the bidders, or if the collusion is between or
among the bidders themselves, or between a bidder and a third
party, including any act which restricts, suppresses or nullifies or
tends to restrict, suppress or nullify competition;
(b) if the Procuring Entity’s BAC is found to have failed in following

the prescribed bidding procedures; or
(c) for any justifiable and reasonable ground where the award of the
contract will not redound to the benefit of the Government as
follows:
(i) If the physical and economic conditions have significantly

changed so as to render the project no longer
economically, financially or technically feasible as
determined by the head of the procuring entity;
(ii) If the project is no longer necessary as determined by the

head of the procuring entity; and
30
(iii) If the source of funds for the project has been withheld or
reduced through no fault of the Procuring Entity.
In addition, the Procuring Entity may likewise declare a failure of bidding when:
(d) No bids are received;
(e) All prospective bidders are declared ineligible;
(f) All bids fail to comply with all the bid requirements or fail post-
qualification; or
(g) The bidder with the Lowest Calculated Responsive Bid refuses,
without justifiable cause to accept the award of contract, and no
award is made.
F. Award of Contract
30. Contract Award

Subject to ITB Clause 28, the Procuring Entity shall award the contract to the
Bidder whose Bid has been determined to be the Lowest Calculated and
Responsive Bid (LCRB).
Prior to the expiration of the period of Bid validity, the Procuring Entity shall
notify the successful Bidder in writing that its Bid has been accepted,
through a Notice of Award received personally or sent by registered mail
or electronically, receipt of which must be confirmed in writing within
two (2) days by the LCRB and submitted personally or sent by registered
mail or electronically to the Procuring Entity.
Notwithstanding the issuance of the Notice of Award, award of contract shall

be subject to the following conditions:
(a) Submission of the following documents within the prescribed

period from receipt by the Bidder of the notice that it has the
Lowest Calculated and Responsive Bid:
(i) Valid JVA, if applicable, within ten (10) calendar days;
(ii) Valid PCAB license and registration for the type and cost of
the contract to be bid for foreign bidders, within thirty (30)
calendar days, followed under a Treaty or International or
Executive Agreement mentioned in ITB Clause 12(a)(iv);
(b) Posting of the performance security in accordance with ITB

Clause 32;
(c) Signing of the contract as provided in ITB Clause 31; and
31
(d) Approval by higher authority, if required.
31. Signing of the Contract

At the same time as the Procuring Entity notifies the successful Bidder that its
Bid has been accepted, the Procuring Entity shall send the Contract Form
to the Bidder, which Contract has been provided in the Bidding
Documents, incorporating therein all agreements between the parties.
Within ten (10) calendar days from receipt of the Notice of Award, the
successful Bidder shall post the required performance security, sign and
date the contract and return it to the Procuring Entity.
The Procuring Entity shall enter into contract with the successful Bidder within
the same ten (10) calendar day period provided that all the documentary
requirements are complied with.
The following documents shall form part of the contract:
(a) Contract Agreement;
(b) Bidding Documents;
(c) Winning bidder’s bid, including the Technical and Financial

Proposals, and all other documents/statements submitted;
(d) Performance Security;
(e) Credit line in accordance with ITB Clause 0, if applicable;
(f) Notice of Award of Contract; and
(g) Other contract documents that may be required by existing laws

and/or specified in the BDS.
32. Performance Security

To guarantee the faithful performance by the winning Bidder of its obligations
under the contract, it shall post a performance security within a
maximum period of ten (10) calendar days from the receipt of the Notice
of Award from the Procuring Entity and in no case later than the signing
of the contract.
The procuring entity shall prescribe at least two (2) acceptable forms of
performance security taken from two (2) categories below that bidders
may opt to use, denominated in Philippine Pesos and posted in favor of
the Procuring Entity in an amount equal to the percentage of the total
contract price as stated in the BDS in accordance with the following
schedule:
32
Amount of Performance Security
Form of Performance Security (Equal to Percentage of the Total
Contract Price)
(a) Bank draft/guarantee or
irrevocable letter of credit
issued by a Universal or
Commercial Bank: Provided,
however, that it shall be Ten percent (10%)
confirmed or authenticated
by a Universal or Commercial
Bank, if issued by a foreign
bank.
(b) Surety bond callable upon
demand issued by a surety or Thirty percent (30%)
insurance company duly
certified by the Insurance
Commission as authorized to
issue such security; and/or
Failure of the successful Bidder to comply with the above-mentioned

requirement shall constitute sufficient ground for the annulment of the
award and forfeiture of the bid security, in which event the Procuring
Entity shall initiate and complete the post qualification of the second
Lowest Calculated Bid. The procedure shall be repeated until the Lowest
Calculated and Responsive Bid is identified and selected for contract
award. However, if no Bidder passed post-qualification, the BAC shall
declare the bidding a failure and conduct a re-bidding with re-
advertisement.
33. Notice to Proceed

Within three (3) calendar days from the date of approval of the Contract by the
appropriate government approving authority, the Procuring Entity shall
issue its Notice to Proceed to the Bidder.
The contract effectively date shall be provided in the Notice to Proceed by the
Procuring Entity, which date shall not be later than seven (7) calendar
days from the issuance of the Notice to Proceed.
33
Section III. Bid Data Sheet
34
Bid Data Sheet
ITB Clause
0 The PROCURING ENTITY is Department of Public Works and Highways,
Surigao del Sur 2nd Engineering District, Bislig City, Surigao del Sur.
The name of the Contract is
Installation of the Structured Network Cabling and Electrical
The identification number of the Contract is 17NI0057 (Re-ad).
2 The Funding Source is:

The Government of the Philippines (GOP) through FY 2016 RA 10717
EXTENDED Regular 2016 Continuing
17NI0057 (Re-ad) - Installation of the Structured Network Cabling
and Electrical Requirements in the new DPWH Surigao del Sur 2nd
DEO Building
3.1 No further instructions.

0 Bidding is restricted to eligible bidders as defined in ITB Clause 0.
0 No further instructions.
For this purpose, similar contracts shall refer to
17NI0057 (Re-ad) - Installation of the Structured Network Cabling
and Electrical Requirements in the new DPWH Surigao del Sur 2nd
DEO Building
0 “Subcontracting is not allowed.”
“Not applicable”.
0 The Procuring Entity will hold a pre-bid conference for this Project on
September 12, 2017 at DPWH Surigao del Sur 2ndDistrict Engineering Office,
Bislig City, Surigao del Sur.
0 The Procuring Entity’s address is:

Department of Public Works and Highways
Surigao del Sur Second District Engineering Office
Bislig City, Surigao del Sur
No further instructions.
35
0 If the Procuring Entity maintains a registry system using the PhilGEPS or its
own electronic system:
The first envelope shall contain the eligibility and technical documents stated
in the ITB Clause. However, if the Bidder maintains a current and updated
file of his Class “A” Documents with the Procuring Entity, a written letter of
intent may be submitted in lieu of the Class “A” Documents; otherwise, it
shall submit an application for eligibility and its latest Class “A” Documents
12(a)(i) “No other acceptable proof of registration is recognized.”

12(a)(iv) No further instructions.
12.1(b)(ii.2) The Contractor shall employ the following Key Personnel:
17NI0057 (Re-ad)
Installation of the Structured Network Cabling and Electrical

T E C H N I C A L
MANPOWER REQUIRED
PERSONNEL NUMBER
Foreman 1
Electrician 1
Skilled 1
Welder 1
I. Technology 2
A.C. Technician 1
Laborer 4
Note:
Also attached the following documents:
 Certified Photocopy of Professional License
 Certified Photocopy of Professional Tax Receipt
 Certified Photocopy of Certificate of Accreditation for Materials
Engineer I.
 Certified Photocopy of Certificate of Trainings for the Const.
Safety & Health Officer
12(b)(ii.3) The minimum equipment requirements are the following:

NOTE:
1. Show proof of ownership of the equipment’s.
2. Attached contract if to be purchased or rented.
3. If to be leased, and/or under purchase agreements, It should be
supported by a certification of availability of equipment from the
equipment lessor/vendor for the duration of the project;
36
The pledged equipment shall be listed in complete to include the
brand, engine, chassis and serial numbers, capacity, present
location and must be ready for inspection during the post
qualification stage.
Failure of the prospective bidder to state a complete technical
description of the pledged equipment and the specific location,
whether owned, leased or under purchased agreement shall result
in the bidder’s automatic post-disqualification for award of
contract and forfeiture of its bid security (D.O. 58 series of 2012).
LIST OF CONTRACTOR’S EQUIPMENT PLEDGE TO THE CONTRACT
Contract ID No.: __________________________________________________

Contract Name: ___________________________________________________
___________________________________________________
Location of the Contract: _____________________________________________
Capacit
No. Model/ y/ Proof of
Perform Motor
of Year Plate Specific Condi Ownership/
Description ance No./
Unit( Manufa No. Location tion Lessor or
Body No.
s) ctured Vendor
Size
A. Owned
B. Leased
C. Under
Purchase
Agreement
Failure of the prospective bidder to state a complete technical description of the

pledge equipment and the specific location, whether owned, leased or under
purchased agreement shall result in the bidder’s automatic post- disqualification for
award of contract and forfeiture of its bid security.
___________________________________
_____________________
(Name/Signature of Bidder’s Representative)
Date
____________________________________
(Name of Bidder)
37
17NI0057 (Re-ad) - Installation of the Structured Network
Cabling and Electrical Requirements in the new DPWH Surigao del
Sur 2nd DEO Building
T E C H N I C A L
EQUIPMENT REQUIRED
NUMBER
DESCRIPTION
NEDDED/AVAILABLE
Welding machine 1
A. ADDITIONAL REQUIREMENTS:
- Duly signed Bid Prices in the Bill of Quantities

- Duly signed Detailed Estimates
- Summary Sheet indicating the unit prices of Construction Materials,
Labor Rates and Equipment Rentals
- Duly signed Cash Flow by Quarter and Payment Schedule
13(b) The ABC is Three Million Seven Hundred Eighty Two Thousand Five
Hundred Ninety Two Pesos Only and 58/100 (PHP 3,782,592.58)
Any bid with a financial component exceeding this amount shall not be
accepted.
0 “No further instructions.”

0 No further instruction.
0 The bid prices shall be quoted in Philippine Pesos.
0 Bids will be valid until Two Hundred Ten Calendar Days (210 CD) from
the Opening of Bids.
The bid security shall be limited to Bid Securing Declaration (BSD) or one
other form in accordance with the following amount:
1. The amount Seven Five Thousand Six Hundred Fifty One Pesos and
85/100 (Php75,651.85) if bid security is in Bank draft/guarantee or
irrevocable letter of credit issued by a Universal or Commercial Bank:
Provided, however, that it shall be confirmed or authenticated by a
Universal or Commercial Bank, if issued by a foreign bank. (2%)
2. The amount of One Hundred Eighty Nine Thousand One Hundred

Twenty Nine Pesos and 63/100 (Php189,129.63) Surety bond
callable upon demand issued by a surety or insurance company duly
certified by the Insurance Commission as authorized to issue such security.
(5%)
0 The bid security shall be valid until Two Hundred Ten Calendar Days
(210 CD) FROM THE OPENING OF BIDS.
38
0 Each Bidder shall submit original copies of the first and second
components of its bid. It must be book bounded with index tab on
each of the documents required. The contents are all
numbered/paginated consecutively, the total number of which are
indicated in the checklist of the requirements and signed by the
duly authorized representative.
21 The address for submission of bids is
The Chairman,
Bids and Awards Committee
Surigao del Sur 2nd Engineering District
The deadline for submission of bids is October 25, 2017 at 10:00 A. M.

0 The place of bid opening is
Bids and Awards Committee Office

Surigao del Sur 2nd Engineering District
The date and time of bid opening is October 25, 2017 at 10:00 A. M.

27(d) Bid Modification is not allowed.
28(b) Only tax returns filed and taxes paid through the BIR Electronic Filling and
payment System (EFPS) shall be accepted.
NOTE: The latest income and business tax returns are those within the last
six months preceding the date of bid submission.
39
Requirements:
Contract ID:
Contract Name:
Location of the Contract:
BAC’s CHECKLIST OF TECHNICAL ENVELOPE REQUIREMENTS
I . TECHNICAL DOCUMENTS : B
Bid Security: Bid

Securing Declaration
and one(1) other form
1. ( ) Sufficient ( ) Insufficient
as specified in Section
27.2 of the Revised
IRR (7th Edition)
Form of Bid Security :
Issuing Company :
Number :
Official Receipt No. :
Bid Security Amount :
Validity Period :
2. Duly signed Organizational Chart for the Project.
Duly signed Contractor's Certificate of Key Personnel for the Contract, with Key Personnel's Affidavits of Commitment
3. to Work on the Contract with Complete Qualification & Experience Data.
4. Duly Signed List of Contractor’s Equipment Pledged to the Contract supported with Proof of Ownership.
5. Minimum Materials Testing Equipment (D.O.138 series of 2015)
SWORN STATEMENT IN ACCORDANCE WITH SECTION 25.2 (b) (IV) OF THE IRR OF R.A. 9184.
6. Not blacklisted Contractor.

7. Documents submitted are Authenticated.
Authorizing Head of the Procuring Entity or its Duly Authorized Representative(s) to verify all the Documents
8.
submitted.
9. Disclosure Provision.
10. Duly signed Statement not to give or pay directly or indirectly, any commission, amount, fee, or any form of
consideration, pecuniary or otherwise, to any person or official, personnel or representative of the government
in relation to any procurement project or activity.
11. Sworn Statement that it complies with Section II-A-4, (Conflict of Interest)
provided in the Bidding Documents.
BAC's CHECKLIST OF FINANCIAL ENVELOPE REQUIREMENTS
1 Form of Bid
2 Duly signed Bid Prices in the Bill of Quantities
3 Duly signed Detailed Estimates
4 Duly signed Cash Flow by Quarter and Payment Schedule
Initials of BAC Members if all the documents are included
40
Conflict of Interest, Section II-A-4 (PBD 3rd Ed.)
POST- QUALIFICATION REQUIREMENTS
 Verification of:
*Legal - licenses, certificates, permits

*Technical – work experience, key personnel, availability of equipment; slippage in-on going
projects, authenticity of bid security
*Financial
 Submission of the following documents:
*Tax Clearance
*Mayor’s Permit
*Latest Income and Business Tax Returns
*Certificate of PhilGEPS Registration
*Contractor’s Registration Certificate
*Other appropriate licenses
Note: To be attached as part of the Contents of the First Envelope.
32.2 The performance security shall be in the following amount:

1. The amount of 10% OF THE CONTRACT PRICE, if performance security
is in cash, cashier’s/manager’s check, bank draft/guarantee or
irrevocable letter of credit; OR
2. The amount of 30% OF THE CONTRACT PRICE, if performance security
is in Surety Bond;
41
Section IV. General Conditions of Contract
42
TABLE OF CONTENTS
1. DEFINITIONS .......................................................................... 46
2. INTERPRETATION .................................................................... 48
3. GOVERNING LANGUAGE AND LAW ............................................... 48
4. COMMUNICATIONS................................................................... 49
5. POSSESSION OF SITE................................................................ 49
6. THE CONTRACTOR’S OBLIGATIONS .............................................. 49
7. PERFORMANCE SECURITY .......................................................... 50
8. SUBCONTRACTING ................................................................... 51
9. LIQUIDATED DAMAGES ............................................................. 52
10. ......................................................................................... SITE INVESTIGATION
REPORTS ............................................................................... 52
11. ....................................................... THE PROCURING ENTITY, LICENSES AND
PERMITS................................................................................ 52
12. ............................................................ CONTRACTOR’S RISK AND WARRANTY
SECURITY .............................................................................. 52
13. ............................................................................................... LIABILITY OF THE
CONTRACTOR.......................................................................... 55
14. ........................................................................................ PROCURING ENTITY’S
RISK ..................................................................................... 55
15. ..........................................................................................................INSURANCE
........................................................................................... 56
16. ....................................................................... TERMINATION FOR DEFAULT OF
CONTRACTOR.......................................................................... 57
17. ................................................. TERMINATION FOR DEFAULT OF PROCURING
ENTITY .................................................................................. 58
18. ................................................................................ TERMINATION FOR OTHER
CAUSES ................................................................................. 58
19. ................................................................ PROCEDURES FOR TERMINATION OF
CONTRACTS ............................................................................ 60
20. .................................................................... FORCE MAJEURE, RELEASE FROM
PERFORMANCE ........................................................................ 63
43
21. .................................................................................................. RESOLUTION OF
DISPUTES .............................................................................. 63
22. .................................................. SUSPENSION OF LOAN, CREDIT, GRANT, OR
APPROPRIATION ..................................................................... 64
23. ..................................................... PROCURING ENTITY’S REPRESENTATIVE’S
DECISIONS............................................................................. 64
24. . APPROVAL OF DRAWINGS AND TEMPORARY WORKS BY THE PROCURING
ENTITY’S REPRESENTATIVE ........................................................ 64
25. ....... ACCELERATION AND DELAYS ORDERED BY THE PROCURING ENTITY’S
REPRESENTATIVE..................................................................... 65
26. .................................................. EXTENSION OF THE INTENDED COMPLETION
DATE .................................................................................... 65
27. ............................................................................................................. RIGHT TO
VARY .................................................................................... 65
28. .................................................................................. CONTRACTORS RIGHT TO
CLAIM ................................................................................... 66
29. .......................................................................................................... DAYWORKS
........................................................................................... 66
30. ...................................................................................................................EARLY
WARNING .............................................................................. 66
31. ....................................................................................................... PROGRAM OF
WORK ................................................................................... 67
32. ..................................................................................................... MANAGEMENT
CONFERENCES......................................................................... 67
33. ................................................................................................................ BILL OF
QUANTITIES ........................................................................... 68
34. ................................................................. INSTRUCTIONS, INSPECTIONS AND
AUDITS ................................................................................. 68
35. .......................................................................................................IDENTIFYING
DEFECTS ................................................................................ 68
36. ............................................................................................................... COST OF
REPAIRS ................................................................................ 69
37. ..................................................................................................CORRECTION OF
DEFECTS ................................................................................ 69
44
38. .................................................................................................... UNCORRECTED
DEFECTS ................................................................................ 69
39. ............................................................................................................. ADVANCE
PAYMENT ............................................................................... 69
40. ........................................................................................................... PROGRESS
PAYMENTS ............................................................................. 70
41. ............................................................................................................. PAYMENT
CERTIFICATES ......................................................................... 71
42. .......................................................................................................... RETENTION
........................................................................................... 71
43. .......................................................................................................... VARIATION
ORDERS ................................................................................ 72
44. ........................................................................................................... CONTRACT
COMPLETION .......................................................................... 74
45. .................................................................................................. SUSPENSION OF
WORK ................................................................................... 74
46. ....................................................................................................... PAYMENT ON
TERMINATION......................................................................... 75
47. ................................................................................. EXTENSION OF CONTRACT
TIME..................................................................................... 75
48. ................................................................................................................... PRICE
ADJUSTMENT .......................................................................... 77
49. ....................................................................................................... COMPLETION
........................................................................................... 77
50. ................................................................................................................ TAKING
OVER .................................................................................... 77
51. .......................................................................OPERATING AND MAINTENANCE
MANUALS .............................................................................. 77
45
1. Definitions
For purposes of this Clause, boldface type is used to identify defined terms.
1.1. The Arbiter is the person appointed jointly by the Procuring Entity and
the Contractor to resolve disputes in the first instance, as provided for
in GCC Clause 21.
1.2. Bill of Quantities refers to a list of the specific items of the Work and
their corresponding unit prices, lump sums, and/or provisional sums.
1.3. The Completion Date is the date of completion of the Works as

certified by the Procuring Entity’s Representative, in accordance with
GCC Clause 49.
1.4. The Contract is the contract between the Procuring Entity and the
Contractor to execute, complete, and maintain the Works.
1.5. The Contract Price is the price stated in the Letter of Acceptance and
thereafter to be paid by the Procuring Entity to the Contractor for the
execution of the Works in accordance with this Contract.
1.6. Contract Time Extension is the allowable period for the Contractor to
complete the Works in addition to the original Completion Date stated in
this Contract.
1.7. The Contractor is the juridical entity whose proposal has been accepted
by the Procuring Entity and to whom the Contract to execute the Work
was awarded.
1.8. The Contractor’s Bid is the signed offer or proposal submitted by the
Contractor to the Procuring Entity in response to the Bidding Documents.
1.9. Days are calendar days; months are calendar months.
1.10. Dayworks are varied work inputs subject to payment on a time basis
for the Contractor’s employees and Equipment, in addition to payments
for associated Materials and Plant.
1.11. A Defect is any part of the Works not completed in accordance with the
Contract.
1.12. The Defects Liability Certificate is the certificate issued by Procuring

Entity’s Representative upon correction of defects by the Contractor.
1.13. The Defects Liability Period is the one year period between contract
completion and final acceptance within which the Contractor assumes
the responsibility to undertake the repair of any damage to the Works
at his own expense.
46
1.14. Drawings are graphical presentations of the Works. They include all
supplementary details, shop drawings, calculations, and other
information provided or approved for the execution of this Contract.
1.15. Equipment refers to all facilities, supplies, appliances, materials or

things required for the execution and completion of the Work provided
by the Contractor and which shall not form or are not intended to form
part of the Permanent Works.
1.16. The Intended Completion Date refers to the date specified in the
SCC when the Contractor is expected to have completed the Works. The
Intended Completion Date may be revised only by the Procuring Entity’s
Representative by issuing an extension of time or an acceleration order.
1.17. Materials are all supplies, including consumables, used by the

Contractor for incorporation in the Works.
1.18. The Notice to Proceed is a written notice issued by the Procuring Entity
or the Procuring Entity’s Representative to the Contractor requiring the
latter to begin the commencement of the work not later than a specified
or determinable date.
1.19. Permanent Works all permanent structures and all other project
features and facilities required to be constructed and completed in
accordance with this Contract which shall be delivered to the Procuring
Entity and which shall remain at the Site after the removal of all
Temporary Works.
1.20. Plant refers to the machinery, apparatus, and the like intended to form
an integral part of the Permanent Works.
1.21. The Procuring Entity is the party who employs the Contractor to carry
out the Works stated in the SCC.
1.22. The Procuring Entity’s Representative refers to the Head of the

Procuring Entity or his duly authorized representative, identified in the
SCC, who shall be responsible for supervising the execution of the Works
and administering this Contract.
1.23. The Site is the place provided by the Procuring Entity where the Works
shall be executed and any other place or places which may be
designated in the SCC, or notified to the Contractor by the Procuring
Entity’s Representative as forming part of the Site.
1.24. Site Investigation Reports are those that were included in the
Bidding Documents and are factual and interpretative reports about the
surface and subsurface conditions at the Site.
1.25. Slippage is a delay in work execution occurring when actual

accomplishment falls below the target as measured by the difference
47
between the scheduled and actual accomplishment of the Work by the
Contractor as established from the work schedule. This is actually
described as a percentage of the whole Works.
1.26. Specifications means the description of Works to be done and the

qualities of materials to be used, the equipment to be installed and the
mode of construction.
1.27. The Start Date, as specified in the SCC, is the date when the Contractor
is obliged to commence execution of the Works. It does not necessarily
coincide with any of the Site Possession Dates.
1.28. A Subcontractor is any person or organization to whom a part of the

Works has been subcontracted by the Contractor, as allowed by the
Procuring Entity, but not any assignee of such person.
1.29. Temporary Works are works designed, constructed, installed, and

removed by the Contractor that are needed for construction or
installation of the Permanent Works.
1.30. Work(s)refer to the Permanent Works and Temporary Works to be

executed by the Contractor in accordance with this Contract, including
(i) the furnishing of all labor, materials, equipment and others incidental,
necessary or convenient to the complete execution of the Works; (ii) the
passing of any tests before acceptance by the Procuring Entity’s
Representative; (iii) and the carrying out of all duties and obligations of
the Contractor imposed by this Contract as described in the SCC.
2. Interpretation
In interpreting the Conditions of Contract, singular also means plural, male also
means female or neuter, and the other way around. Headings have no
significance. Words have their normal meaning under the language of
this Contract unless specifically defined. The Procuring Entity’s
Representative will provide instructions clarifying queries about the
Conditions of Contract.
If sectional completion is specified in the SCC, references in the Conditions of

Contract to the Works, the Completion Date, and the Intended Completion
Date apply to any Section of the Works (other than references to the
Completion Date and Intended Completion Date for the whole of the
Works).
3. Governing Language and Law

This Contract has been executed in the English language, which shall be the
binding and controlling language for all matters relating to the meaning
or interpretation of this Contract. All correspondence and other
48
documents pertaining to this Contract which are exchanged by the
parties shall be written in English.
This Contract shall be interpreted in accordance with the laws of the Republic
of the Philippines.
4. Communications
Communications between parties that are referred to in the Conditions shall be
effective only when in writing. A notice shall be effective only when it is
received by the concerned party.
5. Possession of Site
On the date specified in the SCC, the Procuring Entity shall grant the Contractor
possession of so much of the Site as may be required to enable it to
proceed with the execution of the Works. If the Contractor suffers delay
or incurs cost from failure on the part of the Procuring Entity to give
possession in accordance with the terms of this clause, the Procuring
Entity’s Representative shall give the Contractor a Contract Time
Extension and certify such sum as fair to cover the cost incurred, which
sum shall be paid by Procuring Entity.
If possession of a portion is not given by the date stated in the SCC Clause 0,
the Procuring Entity will be deemed to have delayed the start of the
relevant activities. The resulting adjustments in contact time to address
such delay shall be in accordance with GCC Clause 47.
The Contractor shall bear all costs and charges for special or temporary right-
of-way required by it in connection with access to the Site. The
Contractor shall also provide at his own cost any additional facilities
outside the Site required by it for purposes of the Works.
The Contractor shall allow the Procuring Entity’s Representative and any person
authorized by the Procuring Entity’s Representative access to the Site
and to any place where work in connection with this Contract is being
carried out or is intended to be carried out.
6. The Contractor’s Obligations

The Contractor shall carry out the Works properly and in accordance with this
Contract. The Contractor shall provide all supervision, labor, Materials,
Plant and Contractor's Equipment, which may be required. All Materials
and Plant on Site shall be deemed to be the property of the Procuring
Entity.
The Contractor shall commence execution of the Works on the Start Date and
shall carry out the Works in accordance with the Program of Work
submitted by the Contractor, as updated with the approval of the
49
Procuring Entity’s Representative, and complete them by the Intended
Completion Date.
The Contractor shall be responsible for the safety of all activities on the Site.
The Contractor shall carry out all instructions of the Procuring Entity’s
Representative that comply with the applicable laws where the Site is
located.
The Contractor shall employ the key personnel named in the Schedule of Key
Personnel, as referred to in the SCC, to carry out the supervision of the
Works. The Procuring Entity will approve any proposed replacement of
key personnel only if their relevant qualifications and abilities are equal
to or better than those of the personnel listed in the Schedule.
If the Procuring Entity’s Representative asks the Contractor to remove a

member of the Contractor’s staff or work force, for justifiable cause, the
Contractor shall ensure that the person leaves the Site within seven (7)
days and has no further connection with the Work in this Contract.
During Contract implementation, the Contractor and his subcontractors shall

abide at all times by all labor laws, including child labor related
enactments, and other relevant rules.
The Contractor shall submit to the Procuring Entity for consent the name and
particulars of the person authorized to receive instructions on behalf of
the Contractor.
The Contractor shall cooperate and share the Site with other contractors, public
authorities, utilities, and the Procuring Entity between the dates given in
the schedule of other contractors particularly when they shall require
access to the Site. The Contractor shall also provide facilities and
services for them during this period. The Procuring Entity may modify
the schedule of other contractors, and shall notify the Contractor of any
such modification thereto.
Should anything of historical or other interest or of significant value be

unexpectedly discovered on the Site, it shall be the property of the
Procuring Entity. The Contractor shall notify the Procuring Entity’s
Representative of such discoveries and carry out the Procuring Entity’s
Representative’s instructions in dealing with them.
7. Performance Security
Within ten (10) calendar days from receipt of the Notice of Award from the
Procuring Entity but in no case later than the signing of the contract by
both parties, the Contractor shall furnish the performance security in any
the forms prescribed in ITB Clause 0.
50
The performance security posted in favor of the Procuring Entity shall be
forfeited in the event it is established that the Contractor is in default in
any of its obligations under the Contract.
The performance security shall remain valid until issuance by the Procuring
Entity of the Certificate of Final Acceptance.
The performance security may be released by the Procuring Entity and returned
to the Contractor after the issuance of the Certificate of Final Acceptance
subject to the following conditions:
(a) There are no pending claims against the Contractor or the surety
company filed by the Procuring Entity;
(b) The Contractor has no pending claims for labor and materials filed
against it; and
(c) Other terms specified in the SCC.
The Contractor shall post an additional performance security following the

amount and form specified in ITB Clause 0 to cover any cumulative
increase of more than ten percent (10%) over the original value of the
contract as a result of amendments to order or change orders, extra
work orders and supplemental agreements, as the case may be. The
Contractor shall cause the extension of the validity of the performance
security to cover approved contract time extensions.
In case of a reduction in the contract value or for partially completed Works

under the contract which are usable and accepted by the Procuring
Entity the use of which, in the judgment of the implementing agency or
the Procuring Entity, will not affect the structural integrity of the entire
project, the Procuring Entity shall allow a proportional reduction in the
original performance security, provided that any such reduction is more
than ten percent (10%) and that the aggregate of such reductions is not
more than fifty percent (50%) of the original performance security.
Unless otherwise indicated in the SCC, the Contractor, by entering into the
Contract with the Procuring Entity, acknowledges the right of the
Procuring Entity to institute action pursuant to Act 3688 against any
subcontractor be they an individual, firm, partnership, corporation, or
association supplying the Contractor with labor, materials and/or
equipment for the performance of this Contract.
8. Subcontracting
Unless otherwise indicated in the SCC, the Contractor cannot subcontract
Works more than the percentage specified in ITB Clause 0.
51
Subcontracting of any portion of the Works does not relieve the Contractor of
any liability or obligation under this Contract. The Contractor will be
responsible for the acts, defaults, and negligence of any subcontractor,
its agents, servants or workmen as fully as if these were the Contractor’s
own acts, defaults, or negligence, or those of its agents, servants or
workmen.
Subcontractors disclosed and identified during the bidding may be changed

during the implementation of this Contract, subject to compliance with
the required qualifications and the approval of the Procuring Entity.
9. Liquidated Damages
The Contractor shall pay liquidated damages to the Procuring Entity for each
day that the Completion Date is later than the Intended Completion
Date. The applicable liquidated damages is at least one-tenth (1/10) of
a percent of the cost of the unperformed portion for every day of delay.
The total amount of liquidated damages shall not exceed ten percent
(10%) of the amount of the contract. The Procuring Entity may deduct
liquidated damages from payments due to the Contractor. Payment of
liquidated damages shall not affect the Contractor. Once the cumulative
amount of liquidated damages reaches ten percent (10%) of the amount
of this Contract, the Procuring Entity shall rescind this Contract, without
prejudice to other courses of action and remedies open to it.
If the Intended Completion Date is extended after liquidated damages have

been paid, the Engineer of the Procuring Entity shall correct any
overpayment of liquidated damages by the Contractor by adjusting the
next payment certificate. The Contractor shall be paid interest on the
overpayment, calculated from the date of payment to the date of
repayment, at the rates specified in GCC Clause 0.
10. Site Investigation Reports

The Contractor, in preparing the Bid, shall rely on any Site Investigation Reports
referred to in the SCC supplemented by any information obtained by the
Contractor.
11. The Procuring Entity, Licenses and Permits

The Procuring Entity shall, if requested by the Contractor, assist him in applying
for permits, licenses or approvals, which are required for the Works.
12. Contractor’s Risk and Warranty Security

The Contractor shall assume full responsibility for the Works from the time
project construction commenced up to final acceptance by the Procuring
Entity and shall be held responsible for any damage or destruction of the
Works except those occasioned by force majeure. The Contractor shall
52
be fully responsible for the safety, protection, security, and convenience
of his personnel, third parties, and the public at large, as well as the
Works, Equipment, installation, and the like to be affected by his
construction work.
The defects liability period for infrastructure projects shall be one year from
contract completion up to final acceptance by the Procuring Entity.
During this period, the Contractor shall undertake the repair works, at
his own expense, of any damage to the Works on account of the use of
materials of inferior quality within ninety (90) days from the time the
Head of the Procuring Entity has issued an order to undertake repair. In
case of failure or refusal to comply with this mandate, the Procuring
Entity shall undertake such repair works and shall be entitled to full
reimbursement of expenses incurred therein upon demand.
Unless otherwise indicated in the SCC, in case the Contractor fails to comply
with the preceding paragraph, the Procuring Entity shall forfeit its
performance security, subject its property(ies) to attachment or
garnishment proceedings, and perpetually disqualify it from participating
in any public bidding. All payables of the GOP in his favor shall be offset
to recover the costs.
After final acceptance of the Works by the Procuring Entity, the Contractor shall
be held responsible for “Structural Defects”, i.e., major
faults/flaws/deficiencies in one or more key structural elements of the
project which may lead to structural failure of the completed
elements or structure, or “Structural Failures”, i.e., where one or more
key structural elements in an infrastructure facility fails or collapses,
thereby rendering the facility or part thereof incapable of withstanding
the design loads, and/or endangering the safety of the users or the
general public:
(a) Contractor – Where Structural Defects/Failures arise due to faults

attributable to improper construction, use of inferior
quality/substandard materials, and any violation of the contract
plans and specifications, the contractor shall be held liable;
(b) Consultants – Where Structural Defects/Failures arise due to

faulty and/or inadequate design and specifications as well as
construction supervision, then the consultant who prepared the
design or undertook construction supervision for the project shall
be held liable;
(c) Procuring Entity’s Representatives/Project Manager/Construction

Managers and Supervisors – The project owner’s
representative(s), project manager, construction manager, and
supervisor(s) shall be held liable in cases where the Structural
Defects/Failures are due to his/their willful intervention in altering
the designs and other specifications; negligence or omission in
53
not approving or acting on proposed changes to noted defects or
deficiencies in the design and/or specifications; and the use of
substandard construction materials in the project;
(d) Third Parties - Third Parties shall be held liable in cases where
Structural Defects/Failures are caused by work undertaken by
them such as leaking pipes, diggings or excavations, underground
cables and electrical wires, underground tunnel, mining shaft and
the like, in which case the applicable warranty to such structure
should be levied to third parties for their construction or
restoration works.
(e) Users - In cases where Structural Defects/Failures are due to

abuse/misuse by the end user of the constructed facility and/or
non–compliance by a user with the technical design limits and/or
intended purpose of the same, then the user concerned shall be
held liable.
The warranty against Structural Defects/Failures, except those occasioned on

force majeure, shall cover the period specified in the SCC reckoned from
the date of issuance of the Certificate of Final Acceptance by the
Procuring Entity.
The Contractor shall be required to put up a warranty security in the form of

cash, bank guarantee, letter of credit, GSIS or surety bond callable on
demand, in accordance with the following schedule:
Minimum Amount in
Form of Warranty Percentage (%) of Total
Contract Price
(f) Cash or letter of credit issued by
Universal or Commercial bank:
provided, however, that the letter
of credit shall be confirmed or Five Percent (5%)
authenticated by a Universal or
Commercial bank, if issued by a
foreign bank
(g) Bank guarantee confirmed by
Universal or Commercial bank:
provided, however, that the letter
of credit shall be confirmed or Ten Percent (10%)
authenticated by a Universal or
Commercial bank, if issued by a
foreign bank
(h) Surety bond callable upon
demand issued by GSIS or any Thirty Percent (30%)
surety or insurance company duly
54
certified by the Insurance
Commission
The warranty security shall be stated in Philippine Pesos and shall remain
effective for one year from the date of issuance of the Certificate of Final
Acceptance by the Procuring Entity, and returned only after the lapse of
said one year period.
In case of structural defects/failure occurring during the applicable warranty

period provided in GCC Clause 0, the Procuring Entity shall undertake
the necessary restoration or reconstruction works and shall be entitled
to full reimbursement by the parties found to be liable for expenses
incurred therein upon demand, without prejudice to the filing of
appropriate administrative, civil, and/or criminal charges against the
responsible persons as well as the forfeiture of the warranty security
posted in favor of the Procuring Entity.
13. Liability of the Contractor

Subject to additional provisions, if any, set forth in the SCC, the Contractor’s
liability under this Contract shall be as provided by the laws of the Republic of
the Philippines.
14. Procuring Entity’s Risk

From the Start Date until the Certificate of Final Acceptance has been issued,
the following are risks of the Procuring Entity:
(a) The risk of personal injury, death, or loss of or damage to

property (excluding the Works, Plant, Materials, and Equipment),
which are due to:
(i) any type of use or occupation of the Site authorized by the

Procuring Entity after the official acceptance of the works;
or
(ii) negligence, breach of statutory duty, or interference with

any legal right by the Procuring Entity or by any person
employed by or contracted to him except the Contractor.
(b) The risk of damage to the Works, Plant, Materials, and Equipment
to the extent that it is due to a fault of the Procuring Entity or in
the Procuring Entity’s design, or due to war or radioactive
contamination directly affecting the country where the Works are
to be executed.
55
15. Insurance
The Contractor shall, under his name and at his own expense, obtain and
maintain, for the duration of this Contract, the following insurance
coverage:
(a) Contractor’s All Risk Insurance;
(b) Transportation to the project Site of Equipment, Machinery, and

Supplies owned by the Contractor;
(c) Personal injury or death of Contractor’s employees; and
(d) Comprehensive insurance for third party liability to Contractor’s

direct or indirect act or omission causing damage to third persons.
The Contractor shall provide evidence to the Procuring Entity’s Representative

that the insurances required under this Contract have been effected and
shall, within a reasonable time, provide copies of the insurance policies
to the Procuring Entity’s Representative. Such evidence and such
policies shall be provided to the Procuring Entity’s through the Procuring
Entity’s Representative.
The Contractor shall notify the insurers of changes in the nature, extent, or
program for the execution of the Works and ensure the adequacy of the
insurances at all times in accordance with the terms of this Contract and
shall produce to the Procuring Entity’s Representative the insurance
policies in force including the receipts for payment of the current
premiums.
The above insurance policies shall be obtained from any reputable

insurance company approved by the Procuring Entity’s Representative.
If the Contractor fails to obtain and keep in force the insurances referred to
herein or any other insurance which he may be required to obtain under
the terms of this Contract, the Procuring Entity may obtain and keep in
force any such insurances and pay such premiums as may be necessary
for the purpose. From time to time, the Procuring Entity may deduct the
amount it shall pay for said premiums including twenty five percent
(25%) therein from any monies due, or which may become due, to the
Contractor, without prejudice to the Procuring Entity exercising its right
to impose other sanctions against the Contractor pursuant to the
provisions of this Contract.
In the event the Contractor fails to observe the above safeguards, the Procuring
Entity may, at the Contractor’s expense, take whatever measure is
deemed necessary for its protection and that of the Contractor’s
personnel and third parties, and/or order the interruption of dangerous
Works. In addition, the Procuring Entity may refuse to make the
56
payments under GCC Clause 40 until the Contractor complies with this
Clause.
The Contractor shall immediately replace the insurance policy obtained as

required in this Contract, without need of the Procuring Entity’s demand,
with a new policy issued by a new insurance company acceptable to the
Procuring Entity for any of the following grounds:
(e) The issuer of the insurance policy to be replaced has:
(i) become bankrupt;
(ii) been placed under receivership or under a management

committee;
(iii) been sued for suspension of payment; or
(iv) been suspended by the Insurance Commission and its

license to engage in business or its authority to issue
insurance policies cancelled; or
(v) Where reasonable grounds exist that the insurer may not
be able, fully and promptly, to fulfill its obligation under
the insurance policy.
16. Termination for Default of Contractor

The Procuring Entity shall terminate this Contract for default when any of the
following conditions attend its implementation:
Due to the Contractor’s fault and while the project is on-going, it has incurred
negative slippage of fifteen percent (15%) or more in accordance with
Presidential Decree 1870, regardless of whether or not previous
warnings and notices have been issued for the Contractor to improve his
performance;
Due to its own fault and after this Contract time has expired, the Contractor
incurs delay in the completion of the Work after this Contract has
expired; or
The Contractor:
(a) abandons the contract Works, refuses or fails to comply with a

valid instruction of the Procuring Entity or fails to proceed
expeditiously and without delay despite a written notice by the
Procuring Entity;
(b) does not actually have on the project Site the minimum essential
equipment listed on the Bid necessary to prosecute the Works in
57
accordance with the approved Program of Work and equipment
deployment schedule as required for the project;
(c) does not execute the Works in accordance with this Contract or
persistently or flagrantly neglects to carry out its obligations
under this Contract;
(d) neglects or refuses to remove materials or to perform a new Work

that has been rejected as defective or unsuitable; or
(e) sub-lets any part of this Contract without approval by the

Procuring Entity.
All materials on the Site, Plant, Equipment, and Works shall be deemed to be
the property of the Procuring Entity if this Contract is rescinded because
of the Contractor’s default.
17. Termination for Default of Procuring Entity

The Contractor may terminate this Contract with the Procuring Entity if the
works are completely stopped for a continuous period of at least sixty (60)
calendar days through no fault of its own, due to any of the following reasons:
(a) Failure of the Procuring Entity to deliver, within a reasonable time,

supplies, materials, right-of-way, or other items it is obligated to furnish
under the terms of this Contract; or
(b) The prosecution of the Work is disrupted by the adverse peace and order
situation, as certified by the Armed Forces of the Philippines Provincial
Commander and approved by the Secretary of National Defense.
18. Termination for Other Causes

The Procuring Entity may terminate this Contract, in whole or in part, at any
time for its convenience. The Head of the Procuring Entity may
terminate this Contract for the convenience of the Procuring Entity if he
has determined the existence of conditions that make Project
Implementation economically, financially or technically impractical
and/or unnecessary, such as, but not limited to, fortuitous event(s) or
changes in law and National Government policies.
The Procuring Entity or the Contractor may terminate this Contract if the other
party causes a fundamental breach of this Contract.
Fundamental breaches of Contract shall include, but shall not be limited to, the
following:
(a) The Contractor stops work for twenty eight (28) days when no
stoppage of work is shown on the current Program of Work and
58
the stoppage has not been authorized by the Procuring Entity’s
Representative;
(b) The Procuring Entity’s Representative instructs the Contractor to

delay the progress of the Works, and the instruction is not
withdrawn within twenty eight (28) days;
(c) The Procuring Entity shall terminate this Contract if the Contractor
is declared bankrupt or insolvent as determined with finality by a
court of competent jurisdiction. In this event, termination will be
without compensation to the Contractor, provided that such
termination will not prejudice or affect any right of action or
remedy which has accrued or will accrue thereafter to the
Procuring Entity and/or the Contractor. In the case of the
Contractor's insolvency, any Contractor's Equipment which the
Procuring Entity instructs in the notice is to be used until the
completion of the Works;
(d) A payment certified by the Procuring Entity’s Representative is

not paid by the Procuring Entity to the Contractor within eighty
four (84) days from the date of the Procuring Entity’s
Representative’s certificate;
(e) The Procuring Entity’s Representative gives Notice that failure to

correct a particular Defect is a fundamental breach of Contract
and the Contractor fails to correct it within a reasonable period of
time determined by the Procuring Entity’s Representative;
(f) The Contractor does not maintain a Security, which is required;
(g) The Contractor has delayed the completion of the Works by the
number of days for which the maximum amount of liquidated
damages can be paid, as defined in the GCC Clause 9; and
(h) In case it is determined prima facie by the Procuring Entity that

the Contractor has engaged, before or during the implementation
of the contract, in unlawful deeds and behaviors relative to
contract acquisition and implementation, such as, but not limited
to, the following:
(i) corrupt, fraudulent, collusive, coercive, and obstructive

practices as defined in ITB Clause 3.1(a), unless otherwise
specified in the SCC;
(ii) drawing up or using forged documents;
(iii) using adulterated materials, means or methods, or

engaging in production contrary to rules of science or the
trade; and
59
(iv) any other act analogous to the foregoing.
The Funding Source or the Procuring Entity, as appropriate, will seek to impose
the maximum civil, administrative and/or criminal penalties available
under the applicable law on individuals and organizations deemed to be
involved with corrupt, fraudulent, or coercive practices.
When persons from either party to this Contract gives notice of a fundamental
breach to the Procuring Entity’s Representative in order to terminate the
existing contract for a cause other than those listed under GCC Clause
0, the Procuring Entity’s Representative shall decide whether the breach
is fundamental or not.
If this Contract is terminated, the Contractor shall stop work immediately, make
the Site safe and secure, and leave the Site as soon as reasonably
possible.
19. Procedures for Termination of Contracts

The following provisions shall govern the procedures for the termination of this
Contract:
(a) Upon receipt of a written report of acts or causes which may

constitute ground(s) for termination as aforementioned, or upon
its own initiative, the Procuring Entity shall, within a period of
seven (7) calendar days, verify the existence of such ground(s)
and cause the execution of a Verified Report, with all relevant
evidence attached;
(b) Upon recommendation by the Procuring Entity, the Head of the

Procuring Entity shall terminate this Contract only by a written
notice to the Contractor conveying the termination of this
Contract. The notice shall state:
(i) that this Contract is being terminated for any of the

ground(s) afore-mentioned, and a statement of the acts
that constitute the ground(s) constituting the same;
(ii) the extent of termination, whether in whole or in part;
(iii) an instruction to the Contractor to show cause as to why

this Contract should not be terminated; and
(iv) special instructions of the Procuring Entity, if any.
The Notice to Terminate shall be accompanied by a copy of the

Verified Report;
(c) Within a period of seven (7) calendar days from receipt of the
Notice of Termination, the Contractor shall submit to the Head of
60
the Procuring Entity a verified position paper stating why the
contract should not be terminated. If the Contractor fails to show
cause after the lapse of the seven (7) day period, either by
inaction or by default, the Head of the Procuring Entity shall issue
an order terminating the contract;
(d) The Procuring Entity may, at any time before receipt of the
Bidder’s verified position paper described in item (c) above
withdraw the Notice to Terminate if it is determined that certain
items or works subject of the notice had been completed,
delivered, or performed before the Contractor’s receipt of the
notice;
(e) Within a non-extendible period of ten (10) calendar days from

receipt of the verified position paper, the Head of the Procuring
Entity shall decide whether or not to terminate this Contract. It
shall serve a written notice to the Contractor of its decision and,
unless otherwise provided in the said notice, this Contract is
deemed terminated from receipt of the Contractor of the notice
of decision. The termination shall only be based on the ground(s)
stated in the Notice to Terminate; and
(f) The Head of the Procuring Entity may create a Contract

Termination Review Committee (CTRC) to assist him in the
discharge of this function. All decisions recommended by the
CTRC shall be subject to the approval of the Head of the Procuring
Entity.
Pursuant to Section 69(f) of RA 9184 and without prejudice to the imposition

of additional administrative sanctions as the internal rules of the agency
may provide and/or further criminal prosecution as provided by
applicable laws, the procuring entity shall impose on contractors after
the termination of the contract the penalty of suspension for one (1)
year for the first offense, suspension for two (2) years for the second
offense from participating in the public bidding process, for violations
committed during the contract implementation stage, which include but
not limited to the following:
(g) Failure of the contractor, due solely to his fault or negligence, to

mobilize and start work or performance within the specified
period in the Notice to Proceed (“NTP”);
(h) Failure by the contractor to fully and faithfully comply with its
contractual obligations without valid cause, or failure by the
contractor to comply with any written lawful instruction of the
procuring entity or its representative(s) pursuant to the
implementation of the contract. For the procurement of
infrastructure projects or consultancy contracts, lawful
instructions include but are not limited to the following:
61
(i) Employment of competent technical personnel, competent
engineers and/or work supervisors;
(ii) Provision of warning signs and barricades in accordance

with approved plans and specifications and contract
provisions;
(iii) Stockpiling in proper places of all materials and removal

from the project site of waste and excess materials ,
including broken pavement and excavated debris in
accordance with approved plans and specifications and
contract provisions;
(iv) Deployment of committed equipment, facilities, support

staff and manpower; and
(v) Renewal of the effectivity dates of the performance

security after its expiration during the course of contract
implementation.
(i) Assignment and subcontracting of the contract or any part thereof

or substitution of key personnel named in the proposal without
prior written approval by the procuring entity.
(j) Poor performance by the contractor or unsatisfactory quality

and/or progress of work arising from his fault or negligence as
reflected in the Constructor's Performance Evaluation System
(“CPES”) rating sheet. In the absence of the CPES rating sheet,
the existing performance monitoring system of the procuring
entity shall be applied. Any of the following acts by the
Contractor shall be construed as poor performance:
(i) Negative slippage of 15% and above within the critical

path of the project due entirely to the fault or negligence
of the contractor; and
(ii) Quality of materials and workmanship not complying with

the approved specifications arising from the contractor's
fault or negligence.
(k) Willful or deliberate abandonment or non-performance of the

project or contract by the contractor resulting to substantial
breach thereof without lawful and/or just cause.
In addition to the penalty of suspension, the performance security

posted by the contractor shall also be forfeited.
62
20. Force Majeure, Release From Performance
For purposes of this Contract the terms “force majeure” and “fortuitous event”
may be used interchangeably. In this regard, a fortuitous event or force
majeure shall be interpreted to mean an event which the Contractor
could not have foreseen, or which though foreseen, was inevitable. It
shall not include ordinary unfavorable weather conditions; and any other
cause the effects of which could have been avoided with the exercise of
reasonable diligence by the Contractor.
If this Contract is discontinued by an outbreak of war or by any other event

entirely outside the control of either the Procuring Entity or the
Contractor, the Procuring Entity’s Representative shall certify that this
Contract has been discontinued. The Contractor shall make the Site safe
and stop work as quickly as possible after receiving this certificate and
shall be paid for all works carried out before receiving it and for any
Work carried out afterwards to which a commitment was made.
If the event continues for a period of eighty four (84) days, either party may
then give notice of termination, which shall take effect twenty eight (28)
days after the giving of the notice.
After termination, the Contractor shall be entitled to payment of the unpaid

balance of the value of the Works executed and of the materials and
Plant reasonably delivered to the Site, adjusted by the following:
(a) any sum to which the Contractor is entitled under GCC Clause
28;
(b) the cost of his suspension and demobilization;
(c) any sum to which the Procuring Entity is entitled.
The net balance due shall be paid or repaid within a reasonable time period
from the time of the notice of termination.
21. Resolution of Disputes

If any dispute or difference of any kind whatsoever shall arise between the
parties in connection with the implementation of the contract covered
by the Act and this IRR, the parties shall make every effort to resolve
amicably such dispute or difference by mutual consultation.
If the Contractor believes that a decision taken by the PROCURING ENTITY’s

Representative was either outside the authority given to the PROCURING
ENTITY’s Representative by this Contract or that the decision was
wrongly taken, the decision shall be referred to the Arbiter indicated in
the SCC within fourteen (14) days of the notification of the PROCURING
ENTITY’s Representative’s decision.
63
Any and all disputes arising from the implementation of this Contract covered
by the R.A. 9184 and its IRR shall be submitted to arbitration in the
Philippines according to the provisions of Republic Act No. 876,
otherwise known as the “ Arbitration Law” and Republic Act 9285,
otherwise known as the “Alternative Dispute Resolution Act of 2004”:
Provided, however, That, disputes that are within the competence of the
Construction Industry Arbitration Commission to resolve shall be referred
thereto. The process of arbitration shall be incorporated as a provision
in this Contract that will be executed pursuant to the provisions of the
Act and its IRR: Provided, further, That, by mutual agreement, the
parties may agree in writing to resort to other alternative modes of
dispute resolution.
22. Suspension of Loan, Credit, Grant, or Appropriation

In the event that the Funding Source suspends the Loan, Credit, Grant, or
Appropriation to the Procuring Entity, from which part of the payments to the
Contractor are being made:
(a) The Procuring Entity is obligated to notify the Contractor of such

suspension within seven (7) days of having received the suspension
notice.
(b) If the Contractor has not received sums due it for work already done
within forty five (45) days from the time the Contractor’s claim for
payment has been certified by the Procuring Entity’s Representative, the
Contractor may immediately issue a suspension of work notice in
accordance with GCC Clause 0.
23. Procuring Entity’s Representative’s Decisions

Except where otherwise specifically stated, the Procuring Entity’s
Representative will decide contractual matters between the Procuring
Entity and the Contractor in the role representing the Procuring Entity.
The Procuring Entity’s Representative may delegate any of his duties and
responsibilities to other people, except to the Arbiter, after notifying the
Contractor, and may cancel any delegation after notifying the
Contractor.
24. Approval of Drawings and Temporary Works by the

Procuring Entity’s Representative
All Drawings prepared by the Contractor for the execution of the Temporary
Works, are subject to prior approval by the Procuring Entity’s
Representative before its use.
The Contractor shall be responsible for design of Temporary Works.
64
The Procuring Entity’s Representative’s approval shall not alter the Contractor’s
responsibility for design of the Temporary Works.
The Contractor shall obtain approval of third parties to the design of the
Temporary Works, when required by the Procuring Entity.
25. Acceleration and Delays Ordered by the Procuring Entity’s

Representative
When the Procuring Entity wants the Contractor to finish before the Intended
Completion Date, the Procuring Entity’s Representative will obtain priced
proposals for achieving the necessary acceleration from the Contractor.
If the Procuring Entity accepts these proposals, the Intended Completion
Date will be adjusted accordingly and confirmed by both the Procuring
Entity and the Contractor.
If the Contractor’s Financial Proposals for an acceleration are accepted by the

Procuring Entity, they are incorporated in the Contract Price and treated
as a Variation.
26. Extension of the Intended Completion Date

The Procuring Entity’s Representative shall extend the Intended Completion
Date if a Variation is issued which makes it impossible for the Intended
Completion Date to be achieved by the Contractor without taking steps
to accelerate the remaining work, which would cause the Contractor to
incur additional costs. No payment shall be made for any event which
may warrant the extension of the Intended Completion Date.
The Procuring Entity’s Representative shall decide whether and by how much
to extend the Intended Completion Date within twenty one (21) days of
the Contractor asking the Procuring Entity’s Representative for a decision
thereto after fully submitting all supporting information. If the
Contractor has failed to give early warning of a delay or has failed to
cooperate in dealing with a delay, the delay by this failure shall not be
considered in assessing the new Intended Completion Date.
27. Right to Vary

The Procuring Entity’s Representative with the prior approval of the Procuring
Entity may instruct Variations, up to a maximum cumulative amount of
ten percent (10%) of the original contract cost.
Variations shall be valued as follows:
(a) At a lump sum price agreed between the parties;
(b) where appropriate, at rates in this Contract;
65
(c) in the absence of appropriate rates, the rates in this Contract shall
be used as the basis for valuation; or failing which
(d) at appropriate new rates, equal to or lower than current industry

rates and to be agreed upon by both parties and approved by the
Head of the Procuring Entity.
28. Contractor's Right to Claim

If the Contractor incurs cost as a result of any of the events under GCC Clause
13, the Contractor shall be entitled to the amount of such cost. If as a result of
any of the said events, it is necessary to change the Works, this shall be dealt
with as a Variation.
29. Dayworks
Subject to GCC Clause 43 on Variation Order, and if applicable as indicated in
the SCC, the Dayworks rates in the Contractor’s Bid shall be used for
small additional amounts of work only when the Procuring Entity’s
Representative has given written instructions in advance for additional
work to be paid for in that way.
All work to be paid for as Dayworks shall be recorded by the Contractor on

forms approved by the Procuring Entity’s Representative. Each
completed form shall be verified and signed by the Procuring Entity’s
Representative within two days of the work being done.
The Contractor shall be paid for Dayworks subject to obtaining signed Dayworks
forms.
30. Early Warning

The Contractor shall warn the Procuring Entity’s Representative at the earliest
opportunity of specific likely future events or circumstances that may
adversely affect the quality of the work, increase the Contract Price, or
delay the execution of the Works. The Procuring Entity’s Representative
may require the Contractor to provide an estimate of the expected effect
of the future event or circumstance on the Contract Price and Completion
Date. The estimate shall be provided by the Contractor as soon as
reasonably possible.
The Contractor shall cooperate with the Procuring Entity’s Representative in

making and considering proposals for how the effect of such an event
or circumstance can be avoided or reduced by anyone involved in the
work and in carrying out any resulting instruction of the Procuring
Entity’s Representative.
66
31. Program of Work
Within the time stated in the SCC, the Contractor shall submit to the Procuring
Entity’s Representative for approval a Program of Work showing the
general methods, arrangements, order, and timing for all the activities
in the Works.
An update of the Program of Work shall the show the actual progress achieved
on each activity and the effect of the progress achieved on the timing of
the remaining work, including any changes to the sequence of the
activities.
The Contractor shall submit to the Procuring Entity’s Representative for

approval an updated Program of Work at intervals no longer than the
period stated in the SCC. If the Contractor does not submit an updated
Program of Work within this period, the PROCURING ENTITY’s
Representative may withhold the amount stated in the SCC from the
next payment certificate and continue to withhold this amount until the
next payment after the date on which the overdue Program of Work has
been submitted.
The Procuring Entity’s Representative’s approval of the Program of Work shall

not alter the Contractor’s obligations. The Contractor may revise the
Program of Work and submit it to the Procuring Entity’s Representative
again at any time. A revised Program of Work shall show the effect of
any approved Variations.
When the Program of Work is updated, the Contractor shall provide the
Procuring Entity’s Representative with an updated cash flow forecast.
The cash flow forecast shall include different currencies, as defined in
the Contract, converted as necessary using the Contract exchange rates.
All Variations shall be included in updated Program of Work produced by the

Contractor.
32. Management Conferences

Either the Procuring Entity’s Representative or the Contractor may require the
other to attend a Management Conference. The Management
Conference shall review the plans for remaining work and deal with
matters raised in accordance with the early warning procedure.
The Procuring Entity’s Representative shall record the business of Management

Conferences and provide copies of the record to those attending the
Conference and to the Procuring Entity. The responsibility of the parties
for actions to be taken shall be decided by the PROCURING ENTITY’s
Representative either at the Management Conference or after the
Management Conference and stated in writing to all who attended the
Conference.
67
33. Bill of Quantities
The Bill of Quantities shall contain items of work for the construction,
installation, testing, and commissioning of work to be done by the
Contractor.
The Bill of Quantities is used to calculate the Contract Price. The Contractor is
paid for the quantity of the work done at the rate in the Bill of Quantities
for each item.
If the final quantity of any work done differs from the quantity in the Bill of
Quantities for the particular item and is not more than twenty five
percent (25%) of the original quantity, provided the aggregate changes
for all items do not exceed ten percent (10%) of the Contract price, the
Procuring Entity’s Representative shall make the necessary adjustments
to allow for the changes subject to applicable laws, rules, and
regulations.
If requested by the Procuring Entity’s Representative, the Contractor shall

provide the Procuring Entity’s Representative with a detailed cost
breakdown of any rate in the Bill of Quantities.
34. Instructions, Inspections and Audits

The Procuring Entity’s personnel shall at all reasonable times during
construction of the Work be entitled to examine, inspect, measure and
test the materials and workmanship, and to check the progress of the
construction.
If the Procuring Entity’s Representative instructs the Contractor to carry out a

test not specified in the Specification to check whether any work has a
defect and the test shows that it does, the Contractor shall pay for the
test and any samples. If there is no defect, the test shall be a
Compensation Event.
The Contractor shall permit the Funding Source named in the SCC to inspect
the Contractor’s accounts and records relating to the performance of the
Contractor and to have them audited by auditors appointed by the
Funding Source, if so required by the Funding Source.
35. Identifying Defects

The Procuring Entity’s Representative shall check the Contractor’s work and
notify the Contractor of any defects that are found. Such checking shall not
affect the Contractor’s responsibilities. The Procuring Entity’s Representative
may instruct the Contractor to search uncover defects and test any work that
the Procuring Entity’s Representative considers below standards and defective.
68
36. Cost of Repairs
Loss or damage to the Works or Materials to be incorporated in the Works
between the Start Date and the end of the Defects Liability Periods shall be
remedied by the Contractor at the Contractor’s cost if the loss or damage arises
from the Contractor’s acts or omissions.
37. Correction of Defects

The Procuring Entity’s Representative shall give notice to the Contractor of any
defects before the end of the Defects Liability Period, which is One (1)
year from project completion up to final acceptance by the Procuring
Entity’s.
Every time notice of a defect is given, the Contractor shall correct the notified
defect within the length of time specified in the Procuring Entity’s
Representative’s notice.
The Contractor shall correct the defects which he notices himself before the
end of the Defects Liability Period.
The Procuring Entity shall certify that all defects have been corrected. If the
Procuring Entity considers that correction of a defect is not essential, he
can request the Contractor to submit a quotation for the corresponding
reduction in the Contract Price. If the Procuring Entity accepts the
quotation, the corresponding change in the SCC is a Variation.
38. Uncorrected Defects

The Procuring Entity shall give the Contractor at least fourteen (14) days’ notice
of his intention to use a third party to correct a Defect. If the Contractor
does not correct the Defect himself within the period, the Procuring
Entity may have the Defect corrected by the third party. The cost of the
correction will be deducted from the Contract Price.
The use of a third party to correct defects that are uncorrected by the
Contractor will in no way relieve the Contractor of its liabilities and
warranties under the Contract.
39. Advance Payment

The Procuring Entity shall, upon a written request of the contractor which shall
be submitted as a contract document, make an advance payment to the
contractor in an amount not exceeding fifteen percent (15%) of the total
contract price, to be made in lump sum or, at the most two, installments
according to a schedule specified in the SCC.
The advance payment shall be made only upon the submission to and
acceptance by the Procuring Entity of an irrevocable standby letter of
69
credit of equivalent value from a commercial bank, a bank guarantee or
a surety bond callable upon demand, issued by a surety or insurance
company duly licensed by the Insurance Commission and confirmed by
the Procuring Entity.
The advance payment shall be repaid by the Contractor by an amount equal to

the percentage of the total contract price used for the advance payment.
The contractor may reduce his standby letter of credit or guarantee instrument
by the amounts refunded by the Monthly Certificates in the advance
payment.
The Procuring Entity will provide an Advance Payment on the Contract Price as
stipulated in the Conditions of Contract, subject to the maximum amount
stated in SCC Clause 0.
40. Progress Payments

The Contractor may submit a request for payment for Work accomplished.
Such request for payment shall be verified and certified by the Procuring
Entity’s Representative/Project Engineer. Except as otherwise stipulated
in the SCC, materials and equipment delivered on the site but not
completely put in place shall not be included for payment.
The Procuring Entity shall deduct the following from the certified gross amounts
to be paid to the contractor as progress payment:
(a) Cumulative value of the work previously certified and paid for.
(b) Portion of the advance payment to be recouped for the month.
(c) Retention money in accordance with the condition of contract.
(d) Amount to cover third party liabilities.
(e) Amount to cover uncorrected discovered defects in the works.
Payments shall be adjusted by deducting therefrom the amounts for advance

payments and retention. The Procuring Entity shall pay the Contractor
the amounts certified by the Procuring Entity’s Representative within
twenty eight (28) days from the date each certificate was issued. No
payment of interest for delayed payments and adjustments shall be
made by the Procuring Entity.
The first progress payment may be paid by the Procuring Entity to the
Contractor provided that at least twenty percent (20%) of the work has
been accomplished as certified by the Procuring Entity’s Representative.
70
Items of the Works for which a price of “0” (zero) has been entered will not be
paid for by the Procuring Entity and shall be deemed covered by other
rates and prices in the Contract.
41. Payment Certificates

The Contractor shall submit to the Procuring Entity’s Representative monthly
statements of the estimated value of the work executed less the
cumulative amount certified previously.
The Procuring Entity’s Representative shall check the Contractor’s monthly

statement and certify the amount to be paid to the Contractor.
The value of Work executed shall:
(a) be determined by the Procuring Entity’s Representative;
(b) comprise the value of the quantities of the items in the Bill of
Quantities completed; and
(c) include the valuations of approved variations.
The Procuring Entity’s Representative may exclude any item certified in a

previous certificate or reduce the proportion of any item previously
certified in any certificate in the light of later information.
42. Retention
The Procuring Entity shall retain from each payment due to the Contractor an
amount equal to a percentage thereof using the rate as specified in ITB
Sub-Clause 0.
Progress payments are subject to retention of ten percent (10%), referred to

as the “retention money.” Such retention shall be based on the total
amount due to the Contractor prior to any deduction and shall be
retained from every progress payment until fifty percent (50%) of the
value of Works, as determined by the Procuring Entity, are completed.
If, after fifty percent (50%) completion, the Work is satisfactorily done
and on schedule, no additional retention shall be made; otherwise, the
ten percent (10%) retention shall again be imposed using the rate
specified therefore.
The total “retention money” shall be due for release upon final acceptance of
the Works. The Contractor may, however, request the substitution of
the retention money for each progress billing with irrevocable standby
letters of credit from a commercial bank, bank guarantees or surety
bonds callable on demand, of amounts equivalent to the retention
money substituted for and acceptable to the Procuring Entity, provided
that the project is on schedule and is satisfactorily undertaken.
71
Otherwise, the ten (10%) percent retention shall be made. Said
irrevocable standby letters of credit, bank guarantees and/or surety
bonds, to be posted in favor of the Government shall be valid for a
duration to be determined by the concerned implementing office/agency
or Procuring Entity and will answer for the purpose for which the ten
(10%) percent retention is intended, i.e., to cover uncorrected
discovered defects and third party liabilities.
On completion of the whole Works, the Contractor may substitute retention

money with an “on demand” Bank guarantee in a form acceptable to the
Procuring Entity.
43. Variation Orders

Variation Orders may be issued by the Procuring Entity to cover any
increase/decrease in quantities, including the introduction of new work
items that are not included in the original contract or reclassification of
work items that are either due to change of plans, design or alignment
to suit actual field conditions resulting in disparity between the
preconstruction plans used for purposes of bidding and the “as staked
plans” or construction drawings prepared after a joint survey by the
Contractor and the Procuring Entity after award of the contract, provided
that the cumulative amount of the Variation Order does not exceed ten
percent (10%) of the original project cost. The addition/deletion of
Works should be within the general scope of the project as bid and
awarded. The scope of works shall not be reduced so as to accommodate
a positive Variation Order. A Variation Order may either be in the form
of a Change Order or Extra Work Order.
A Change Order may be issued by the Procuring Entity to cover any

increase/decrease in quantities of original Work items in the contract.
An Extra Work Order may be issued by the Procuring Entity to cover the
introduction of new work necessary for the completion, improvement or
protection of the project which were not included as items of Work in
the original contract, such as, where there are subsurface or latent
physical conditions at the site differing materially from those indicated
in the contract, or where there are duly unknown physical conditions at
the site of an unusual nature differing materially from those ordinarily
encountered and generally recognized as inherent in the Work or
character provided for in the contract.
Any cumulative Variation Order beyond ten percent (10%) shall be subject of
another contract to be bid out if the works are separable from the
original contract. In exceptional cases where it is urgently necessary to
complete the original scope of work, the Head of the Procuring Entity
may authorize a positive Variation Order go beyond ten percent (10%)
but not more than twenty percent (20%) of the original contract price,
subject to the guidelines to be determined by the GPPB: Provided,
72
however, That appropriate sanctions shall be imposed on the designer,
consultant or official responsible for the original detailed engineering
design which failed to consider the Variation Order beyond ten percent
(10%).
In claiming for any Variation Order, the Contractor shall, within seven (7)
calendar days after such work has been commenced or after the
circumstances leading to such condition(s) leading to the extra cost, and
within twenty-eight (28) calendar days deliver a written communication
giving full and detailed particulars of any extra cost in order that it may
be investigated at that time. Failure to provide either of such notices in
the time stipulated shall constitute a waiver by the contractor for any
claim. The preparation and submission of Variation Orders are as
follows:
(a) If the Procuring Entity’s representative/Project Engineer believes

that a Change Order or Extra Work Order should be issued, he
shall prepare the proposed Order accompanied with the notices
submitted by the Contractor, the plans therefore, his
computations as to the quantities of the additional works involved
per item indicating the specific stations where such works are
needed, the date of his inspections and investigations thereon,
and the log book thereof, and a detailed estimate of the unit cost
of such items of work, together with his justifications for the need
of such Change Order or Extra Work Order, and shall submit the
same to the Head of the Procuring Entity for approval.
(b) The Head of the Procuring Entity or his duly authorized

representative, upon receipt of the proposed Change Order or
Extra Work Order shall immediately instruct the technical staff of
the Procuring Entity’s to conduct an on-the-spot investigation to
verify the need for the Work to be prosecuted. A report of such
verification shall be submitted directly to the Head of the
Procuring Entity or his duly authorized representative.
(c) The, Head of the Procuring Entity or his duly authorized

representative, after being satisfied that such Change Order or
Extra Work Order is justified and necessary, shall review the
estimated quantities and prices and forward the proposal with the
supporting documentation to the Head of Procuring Entity for
consideration.
(d) If, after review of the plans, quantities and estimated unit cost of
the items of work involved, the proper office of the procuring
entity empowered to review and evaluate Change Orders or Extra
Work Orders recommends approval thereof, Head of the
Procuring Entity or his duly authorized representative, believing
the Change Order or Extra Work Order to be in order, shall
approve the same.
73
(e) The timeframe for the processing of Variation Orders from the
preparation up to the approval by the Head of the Procuring Entity
concerned shall not exceed thirty (30) calendar days.
44. Contract Completion

Once the project reaches an accomplishment of ninety five (95%) of the total
contract amount, the Procuring Entity may create an inspectorate team to make
preliminary inspection and submit a punch-list to the Contractor in preparation
for the final turnover of the project. Said punch-list will contain, among others,
the remaining Works, Work deficiencies for necessary corrections, and the
specific duration/time to fully complete the project considering the approved
remaining contract time. This, however, shall not preclude the claim of the
Procuring Entity for liquidated damages.
45. Suspension of Work

The Procuring Entity shall have the authority to suspend the work wholly or
partly by written order for such period as may be deemed necessary,
due to force majeure or any fortuitous events or for failure on the part
of the Contractor to correct bad conditions which are unsafe for workers
or for the general public, to carry out valid orders given by the Procuring
Entity or to perform any provisions of the contract, or due to adjustment
of plans to suit field conditions as found necessary during construction.
The Contractor shall immediately comply with such order to suspend the
work wholly or partly.
The Contractor or its duly authorized representative shall have the right to
suspend work operation on any or all projects/activities along the critical
path of activities after fifteen (15) calendar days from date of receipt of
written notice from the Contractor to the district engineer/regional
director/consultant or equivalent official, as the case may be, due to the
following:
(a) There exist right-of-way problems which prohibit the Contractor

from performing work in accordance with the approved
construction schedule.
(b) Requisite construction plans which must be owner-furnished are

not issued to the contractor precluding any work called for by
such plans.
(c) Peace and order conditions make it extremely dangerous, if not

possible, to work. However, this condition must be certified in
writing by the Philippine National Police (PNP) station which has
responsibility over the affected area and confirmed by the
Department of Interior and Local Government (DILG) Regional
Director.
74
(d) There is failure on the part of the Procuring Entity to deliver
government-furnished materials and equipment as stipulated in
the contract.
(e) Delay in the payment of Contractor’s claim for progress billing

beyond forty-five (45) calendar days from the time the
Contractor’s claim has been certified to by the procuring entity’s
authorized representative that the documents are complete
unless there are justifiable reasons thereof which shall be
communicated in writing to the Contractor.
In case of total suspension, or suspension of activities along the critical path,

which is not due to any fault of the Contractor, the elapsed time between
the effective order of suspending operation and the order to resume
work shall be allowed the Contractor by adjusting the contract time
accordingly.
46. Payment on Termination

If the Contract is terminated because of a fundamental breach of Contract by
the Contractor, the Procuring Entity’s Representative shall issue a
certificate for the value of the work done and Materials ordered less
advance payments received up to the date of the issue of the certificate
and less the percentage to apply to the value of the work not completed,
as indicated in the SCC. Additional Liquidated Damages shall not apply.
If the total amount due to the Procuring Entity exceeds any payment
due to the Contractor, the difference shall be a debt payable to the
Procuring Entity.
If the Contract is terminated for the Procuring Entity’s convenience or because

of a fundamental breach of Contract by the Procuring Entity, the
Procuring Entity’s Representative shall issue a certificate for the value of
the work done, Materials ordered, the reasonable cost of removal of
Equipment, repatriation of the Contractor’s personnel employed solely
on the Works, and the Contractor’s costs of protecting and securing the
Works, and less advance payments received up to the date of the
certificate.
The net balance due shall be paid or repaid within twenty eight (28) days from
the notice of termination.
If the Contractor has terminated the Contract under GCC Clauses 17 or 18, the
Procuring Entity shall promptly return the Performance Security to the
Contractor.
47. Extension of Contract Time

Should the amount of additional work of any kind or other special circumstances
of any kind whatsoever occur such as to fairly entitle the contractor to
75
an extension of contract time, the Procuring Entity shall determine the
amount of such extension; provided that the Procuring Entity is not
bound to take into account any claim for an extension of time unless the
Contractor has, prior to the expiration of the contract time and within
thirty (30) calendar days after such work has been commenced or after
the circumstances leading to such claim have arisen, delivered to the
Procuring Entity notices in order that it could have investigated them at
that time. Failure to provide such notice shall constitute a waiver by the
Contractor of any claim. Upon receipt of full and detailed particulars, the
Procuring Entity shall examine the facts and extent of the delay and shall
extend the contract time completing the contract work when, in the
Procuring Entity’s opinion, the findings of facts justify an extension.
No extension of contract time shall be granted the Contractor due to (a)

ordinary unfavorable weather conditions and (b) inexcusable failure or
negligence of Contractor to provide the required equipment, supplies or
materials.
Extension of contract time may be granted only when the affected activities fall
within the critical path of the PERT/CPM network.
No extension of contract time shall be granted when the reason given to

support the request for extension was already considered in the
determination of the original contract time during the conduct of detailed
engineering and in the preparation of the contract documents as agreed
upon by the parties before contract perfection.
Extension of contract time shall be granted for rainy/unworkable days

considered unfavorable for the prosecution of the works at the site,
based on the actual conditions obtained at the site, in excess of the
number of rainy/unworkable days pre-determined by the Procuring
Entity in relation to the original contract time during the conduct of
detailed engineering and in the preparation of the contract documents
as agreed upon by the parties before contract perfection, and/or for
equivalent period of delay due to major calamities such as exceptionally
destructive typhoons, floods and earthquakes, and epidemics, and for
causes such as non-delivery on time of materials, working drawings, or
written information to be furnished by the Procuring Entity, non-
acquisition of permit to enter private properties within the right-of-way
resulting in complete paralyzation of construction activities, and other
meritorious causes as determined by the Procuring Entity’s
Representative and approved by the Head of the Procuring Entity.
Shortage of construction materials, general labor strikes, and peace and
order problems that disrupt construction operations through no fault of
the Contractor may be considered as additional grounds for extension of
contract time provided they are publicly felt and certified by appropriate
government agencies such as DTI, DOLE, DILG, and DND, among
others. The written consent of bondsmen must be attached to any
76
request of the Contractor for extension of contract time and submitted
to the Procuring Entity for consideration and the validity of the
Performance Security shall be correspondingly extended.
48. Price Adjustment

Except for extraordinary circumstances as determined by NEDA and approved
by the GPPB, no price adjustment shall be allowed. Nevertheless, in cases
where the cost of the awarded contract is affected by any applicable new laws,
ordinances, regulations, or other acts of the GOP, promulgated after the date
of bid opening, a contract price adjustment shall be made or appropriate relief
shall be applied on a no loss-no gain basis.
49. Completion
The Contractor shall request the Procuring Entity’s Representative to issue a
certificate of Completion of the Works, and the Procuring Entity’s
Representative will do so upon deciding that the work is completed.
50. Taking Over

The Procuring Entity shall take over the Site and the Works within seven (7)
days from the date the Procuring Entity’s Representative issues a certificate of
Completion.
51. Operating and Maintenance Manuals

If “as built” Drawings and/or operating and maintenance manuals are required,
the Contractor shall supply them by the dates stated in the SCC.
If the Contractor does not supply the Drawings and/or manuals by the dates
stated in the SCC, or they do not receive the Procuring Entity’s
Representative’s approval, the Procuring Entity’s Representative shall
withhold the amount stated in the SCC from payments due to the
Contractor.
77
Section V. Special Conditions of Contract
78
Special Conditions of Contract
GCC Clause
1.16 The Intended Completion Date is Two Hundred Ten Calendar
Days (210 CD) from the effectivity of the contract.
1.21 The Procuring Entity is Department of Public Works and
Highways, Surigao del Sur 2nd Engineering District, Bislig City,
Surigao del Sur.
1.22 The Procuring Entity’s Representative is
NOEL R. OCLARIT
District Engineer
Surigao del Sur 2ndDistrict Engineering Office
The Procuring Entity’s Authorized Representative is CANDELARIO P.

PORTILLO, Department of Public Works and Highways, Surigao del
Sur 2ndDistrict Engineering Office, Bislig City, Surigao del Sur.
1.23 The Site is located at Bislig City, Surigao Del Sur.
1.27 The Start Date is Seven (7) calendar days upon issuance of the Notice
to Proceed.
1.30 The Works consist of 17NI0057 (Re-ad) - Installation of the
Structured Network Cabling and Electrical Requirements in the
new DPWH Surigao del Sur 2nd DEO Building
0 The Procuring Entity shall give possession of all parts of the Site to
the Contractor UPON ISSUANCE OF NOTICE TO PROCEED.
The Contractor shall employ the following Key Personnel:
T E C H N I C A L
MANPOWER REQUIRED
PERSONNEL NUMBER
Foreman 1
Electrician 1
Skilled 1
Welder 1
I. Technology 2
A.C. Technician 1
Laborer 4
7(c) No further instructions.

10 The site investigation reports are: BORING LOG DATA

79
0 In case of semi-permanent structures, such as buildings of types 1, 2,
and 3 as classified under the National Building Code of the Philippines,
concrete/asphalt roads, concrete river control, drainage, irrigation lined
canals, river landing, deep wells, rock causeway, pedestrian overpass,
and other similar semi-permanent structures: Five (5) years.
13 No additional provision. , if the Contractor is a joint venture, “A
18.3(h)(i) No further instructions.
0 The Arbiter is: Construction Industry Arbitration Commission
0 No days’ work are applicable to the contract.
0 The Contractor shall submit the Program of Work to the Procuring
Entity’s Representative within ten (10) days of delivery of the Letter of
Acceptance.
0 The Funding Source is the Government of the Philippines.
0 The amount of the advance payment is 15% OF THE CONTRACT COST.
0 Materials and equipment delivered on the site but not completely put in
place shall NOT be included for payment.
0 The date by which operating and maintenance manuals are required is
not applicable
The date by which “as built” drawings are required is Thirty (30) days
from completion.
80
Section VI. Specifications
Notes on Specifications
A set of precise and clear specifications is a prerequisite for Bidders to respond realistically and
competitively to the requirements of the Procuring Entity without qualifying or conditioning their
Bids. In the context of international competitive bidding, the specifications must be drafted to
permit the widest possible competition and, at the same time, present a clear statement of the
required standards of workmanship, materials, and performance of the goods and services to
be procured. Only if this is done will the objectives of economy, efficiency, and fairness in
procurement be realized, responsiveness of Bids be ensured, and the subsequent task of Bid
evaluation facilitated. The specifications should require that all goods and materials to be
incorporated in the Works be new, unused, of the most recent or current models, and
incorporate all recent improvements in design and materials unless provided otherwise in the
Contract.
Samples of specifications from previous similar projects are useful in this respect. The use of
metric units is mandatory. Most specifications are normally written specially by the Procuring
Entity or its representative to suit the Works at hand. There is no standard set of Specifications
for universal application in all sectors in all regions, but there are established principles and
practices, which are reflected in these PBDs.
There are considerable advantages in standardizing General Specifications for repetitive Works
in recognized public sectors, such as highways, ports, railways, urban housing, irrigation, and
water supply, in the same country or region where similar conditions prevail. The General
Specifications should cover all classes of workmanship, materials, and equipment commonly
involved in construction, although not necessarily to be used in a particular Works Contract.
Deletions or addenda should then adapt the General Specifications to the particular Works.
Care must be taken in drafting specifications to ensure that they are not restrictive. In the
specification of standards for goods, materials, and workmanship, recognized international
standards should be used as much as possible. Where other particular standards are used,
whether national standards or other standards, the specifications should state that goods,
materials, and workmanship that meet other authoritative standards, and which ensure
substantially equal or higher quality than the standards mentioned, will also be acceptable. The
following clause may be inserted in the SCC.
Sample Clause: Equivalency of Standards and Codes

Wherever reference is made in the Contract to specific standards and codes to be met by the
goods and materials to be furnished, and work performed or tested, the provisions of the latest
current edition or revision of the relevant standards and codes in effect shall apply, unless
otherwise expressly stated in the Contract. Where such standards and codes are national, or
relate to a particular country or region, other authoritative standards that ensure a substantially
equal or higher quality than the standards and codes specified will be accepted subject to the
Procuring Entity’s Representative’s prior review and written consent. Differences between the
standards specified and the proposed alternative standards shall be fully described in writing by
the Contractor and submitted to the Procuring Entity’s Representative at least twenty eight (28)
days prior to the date when the Contractor desires the Procuring Entity’s Representative’s
consent. In the event the Procuring Entity’s Representative determines that such proposed
deviations do not ensure substantially equal or higher quality, the Contractor shall comply with
the standards specified in the documents.
These notes are intended only as information for the PRO Procuring Entity or the person drafting
the Bidding Documents. They should not be included in the final Bidding Documents.
81
Section VII. Drawings
Insert here a list of Drawings. The actual Drawings, including site plans,
should be attached to
(Plans & Drawing Annexed In A Separate Folder)
82
Section VIII. Bill of Quantities
83
Contract ID : 17NI0057 (Re-ad)

Contract Name : Installation of the Structured Network Cabling and Electrical
Requirements in the new DPWH Surigao del Sur 2nd DEO
Building
Contract Location : Bislig City, Surigao del Sur
SUMMARY OF BID PRICES

(All Parts of Bill of Quantities)
Instructions for completing the Summary of Bid Prices:
1. Part No. - Enter the “Part No.” for each section of the BOQ where unit prices are
entered.
2. Part Description – Enter the “Part Description” corresponding to the “Part No.”
3. Total Amount – Enter the “Total Amount” in Pesos for all pages having the same “Part
Description”
Contract ID : 17NI0057 (Re-ad)

Part No. Part Description Total Amount
TOTAL BID PRICE CARRIED FORWARD TO FORM OF BID
TOTAL AMOUNT IN WORD:

Pesos ___________________________________________________________________________
________________________________________________________________________________
Project to be completed within calendar days
Name __________________________________ in the capacity of _____________________

Signed _________________________________ Date ______________________________
Duly authorized to sign the Bid for and on behalf of _________________________________
84
Bill of Quantities

Contract Name: Standard costing for the installation of the structured network cabling and network
electrical requirements at newly constructed building of DPWH Surigao del Sur 2nd
DEO
Part No. I Part Description
(Columns8:33 (1), (2), (3), and (4) are (Columns (5) and (6) are
to be filled up by the Procuring Entity to be filled up by the Bidder)
Pay
Unit Price Amount
Item Description Unit
Quantity (Pesos) (Pesos)
No.
(1) (2) (3) (4) (5) (6)
VOLUME II - PART B- OTHER GENERAL REQUIREMENTS

In words: Pesos In Figures: Php
1100(30) Conduit, Boxes and Fittings L.s 1.00

In Figures: Php
1101(42) Wire and Wiring Devices L.s 1.00

In Figures: Php
Air Conditioning and Ventilation

1200 sets 2.00
System In Figures: Php
1105(2b) Distribution Frame Panel set 1.00
85
In Figures: Php
1105(18) Network Cabling L.s 1.00

In Figures: Php
1106(1) CCTV System L.s 1.00

In Figures: Php
1042(2) Stainless Steel Door L.s 1.00

In Figures: Php
502(1b2) Manholes, Inlet and Catch Basins each 1.00

In Figures: Php
In words: Pesos
Sub-Total for this Page

In Figures: Php
Submitted by:
Date:
Name of the Representative of the Bidder
86
Position
Name of the Bidder
87
Section IX. Bidding Forms
88
TABLE OF CONTENTS
Bid Form ......................................................................................... 90

Form of Contract Agreement ............................................................ 92
Omnibus Sworn Statement ............................................................... 95
89
Contract ID:
Contract Name:
Bid Form
Date:
To: Name of Procuring Entity

Address
We, the undersigned, declare that:
(a) We have examined and have no reservation on the Bidding Documents (BDs),
including Supplemental/Bid Bulletins, for the above stated Contract;
(b) We offer to execute the Works for this Contract in accordance with the said BDs,
including the Bid Data Sheet, General and Special Conditions of Contract,
Specifications and Drawings therein;
(c) we present our Bid to execute the Works, consisting of our Technical Proposal
(Annex “A”) and our Financial Proposal (Annex “B”);
(d) our Technical Proposal includes the following required documents:
(1) Bid Security in the required form, amount and validity period, using Form
DPWH-INFR-09,10, or 11, as applicable (Annex “A-1”)
(2) Organizational Chart for the Contract, using Form DPWH-INFR-13 (Annex "A-3”)
(3) Contractor’s Certification on Key Personnel for the Contract, with the Key
Personnel’s Affidavits of Commitment to Work on the Contract, using form DPWH-
INFR-14 (Annex “A-4”)
(4) List of Contractor’s Major Equipment Pledged for the Contract, using the DPWH-
INFR-15 (Annex “A-6);
(e) Our Financial Proposal includes the following required documents:
(1) This Bid Form (Annex “B-1”)
(2) Bid prices in the Bill of Quantities Form, using the Forms DPWH-INFR-17 and
18 (Annex “B-2”)
(3) Detailed estimates (Annex “B-3”)
(4) Cash flow by the quarter, using Form DPWH-INFR- 19 (Annex “B-4”);
90
(f) The total price of our Bid for this Contract based on the unit prices in the said
Bill of Quantities, excluding any discounts offerd in item (g) below, is: Total Bid
price in words and in figures;
(g) The discounts we offer and the methodology for their application for this
Contract are: __________________;
(h) Our Bid shall be valid for a period of ___________________ days from the date
fixed for the opening of bids in accordance with the Bidding Documents, and it
shall remain binding upon us and may be accepted by you at any time before
the expiration of that period;
(i) If our Bid is accepted and we receive from you a Notice of Award, we commit,
within ten (10) calendar days from our receipt of the said Notice, (1) to submit
to you the required Performance Security and other documents prescribed in the
Bidding Documents, and (2) to sign the Contract Agreement;
(j) We understand that, if the contract is awarded to us, this Bid, together with your
written acceptance thereof through your Notice of Award, shall constitute a
binding contract between us, until a formal Contract Agreement is prepared and
executed;
(k) We understand that you are not bound to accept the Lowest Calculated Bid or
any other Bid that you may receive;
(l) We acknowledge that failure to sign each page of this form of Bid and the
accomplished Bill of Quantities shall be a ground for the rejection of our Bid; and
(m) We likewise certify/confirm that the undersigned is the duly authorized
representative of the Bidder, and granted full power and authority to do, execute
and perform any and all acts necessary to participate, submit the Bid, and to
sign and execute the appropriate contract documents for the abovementioned
Contract.
Name:
In the capacity of:
Signed:
Duly authorized to sign the Bid for and on behalf of:
Date: ___________
91
Contract ID:
Contract Name:
Form of Contract Agreement

KNOW ALL MEN BY THESE PRESENTS:
This CONTRACT AGREEMENT, made this ___ day of _month_, _year, by and
between:
The GOVERNMENT OF THE REPUBLIC OF THE PHILIPPINES through the

Department of Public Works and Highways (DPWH) represented herein
by ___________________________________, duly authorized for this
purpose, with main office address at ______________________, hereinafter
referred to as the “PROCURING ENTITY”;
-and-
_____________________, a single proprietorship/partnership/corporation/

joint venture organized and existing under and by virtue of laws of the Republic
of the Philippines, with main office address at _________________________,
represented herein by ______________________________, duly authorized
for this purpose, hereinafter referred to as the “CONTRACTOR;”
WITNESSETH:
WHEREAS, the PROCURING ENTITY is desirous that the CONTRACTOR execute

the works under Contract ID and Name, hereinafter called the “Works” and the
PROCURING ENTITY has accepted the Calculated Bid of the CONTRACTOR for the
execution and completion of the Works at the calculated unit bid prices shown in the
attached Bill of Quantities, or a total Contract price of amount in words and numbers.
NOW, THEREFORE, for and consideration of the foregoing premises, the parties
hereto agree as follows:
1. In this CONTRACT AGREEMENT, words and expressions shall have the

same meanings as are respectively assigned to them in the Conditions of
Contract hereinafter referred to.
2. The following documents shall be attached, deemed to form, and be read and
construed as part of this CONTRACT AGREEMENT, and shall be interpreted
in the following order of priority:
a. This Contract Agreement
92
Contract ID:
Contract Name:
b. Documents forming part of the Contract Agreement:
(1) Notice of Award (NOA) with the Contractor’s signed “conformed”
(2) CONTRACTOR’s Bid in the Form of Bid, including its Technical

and Financial Components, as calculated by the Procuring Entity
and conformed to by the CONTRACTOR through the NOA.
(3) Instructions to Bidders (ITB) and Bid Data Sheet (BDS)
(4) Supplemental/Bid Bulletins for Bidding Documents
(5) Special conditions of Contract (SCC)
(6) General Conditions of Contract (GCC)
(7) Specifications
(8) Drawings
(9) Performance Security
(10) Other Documents:
(a) Construction Methods
(b) Construction Schedule in the form of PERT/CPM Diagram

or Precedence Diagram and Bar Chart with S-curve, or
other approved tools of project scheduling, and Cash Flow.
(c) Manpower Schedule
(d) Equipment Utilization Schedule
(e) Construction Safety and Health Program initially approved

by the Head of the Procuring Entity
(f) CONTRACTOR’s All Risk Insurance (CARI)
3. In consideration of the payments to be made by the PROCURING ENTITY

to the CONTRACTOR as hereinafter mentioned, the CONTRACTOR hereby
covenants with the PROCURING ENTITY to execute and complete the
Works and remedy any defects therein in conformity with the provisions of
this CONTRACT AGREEMENT in all respects.
4. In Consideration of the execution and completion of the Works by the
CONTRACTOR, the PROCURING ENTITY hereby covenants to pay the
93
Contract ID:
Contract Name:
CONTRACTOR the unit prices in the CONTRACTOR’s Calculated Bid, as

applied to the actual quantities accomplished as certified by the PROCURING
ENTITY under the provisions of this CONTRACT AGREEMENT, at the times
and in the manner prescribed by this CONTRACT AGREEMENT.
IN WITNESS WHEREOF, the parties hereto set their respective hands on the day,
month and year first above written.
PROCURING ENTITY: CONTRACTOR:
Represented by: Represented by:
______________________ _____________________
Witnessed by:
______________________ _____________________
94
Contract ID:
Contract Name:
Omnibus Sworn Statement

AS REQUIRED BY RA 9184-IRR SECTION 25.2b)iv)
REPUBLIC OF THE PHILIPPINES )

CITY/MUNICIPALITY OF ______ ) S.S.
AFFIDAVIT
I, [Name of Affiant], of legal age, [Civil Status], [Nationality], and residing at

[Address of Affiant], after having been duly sworn in accordance with law, do hereby
depose and state that:
1. Select one, delete the other:
If a sole proprietorship: I am the sole proprietor or authorized representative

of [Name of Bidder] with office address at [address of Bidder];
If a partnership, corporation, cooperative, or joint venture: I am the duly

authorized and designated representative of [Name of Bidder] with office
address at [address of Bidder];
2. Select one, delete the other:
If a sole proprietorship: As the owner and sole proprietor or authorized

representative of [Name of Bidder], I have full power and authority to do,
execute and perform any and all acts necessary to participate, submit the bid,
and to sign and execute the ensuing contract for [Name of the Project] of the
[Name of the Procuring Entity] [insert “as shown in the attached duly
notarized Special Power of attorney” for the authorized representative];
If a partnership, corporation, cooperative, or joint venture: I am granted full

power and authority to do, execute and perform any and all acts necessary to
participate, submit the bid and to sign and execute the ensuing contract for
the [Name of Project] of the [Name of the Procuring Entity] accompanied by
the duly notarized Special Power of Attorney, Board/Partnership Resolution, or
Secretary’s Certificate, whichever is applicable;
3. [Name of Bidder] is not “blacklisted” or barred from bidding by the

Government of the Philippines or any of its agencies, offices, corporations, or
95
Contract ID:
Contract Name:
Local Government Units, foreign government/foreign or international

financing institution whose blacklisting rules have been recognized by the
Government Procurement Policy Board;
4. Each of the documents submitted in satisfaction of the bidding requirements

is an authentic copy of the original, complete, and all statements and
information provided therein are true and correct;
5. [Name of Bidder] is authorizing the Head of the Procuring Entity or its duly
authorized representative(s) to verify all the documents submitted;
6. Select one, delete the rest:
If a sole proprietorship: The owner or sole proprietor is not related to the

Head of the Procuring Entity, members of the Bids and Awards Committee
(BAC), the Technical Working Group, and the BAC Secretariat, the head of the
Project Management Office/Implementing Unit, and the project consultants by
consanguinity or affinity up to the third civil degree;
If a partnership or cooperative: None of the officers and members of [Name

of Bidder] is related to the Head of the Procuring Entity, members of the Bids
and Awards Committee (BAC), the Technical Working Group, and the BAC
Secretariat, the head of the Project Management Office/Implementing Unit,
and the project consultants by consanguinity or affinity up to the third civil
degree;
If a corporation or joint venture: None of the officers, directors, and

controlling stockholders of [Name of Bidder] is related to the Head of the
Procuring Entity, members of the Bids and Awards Committee (BAC), the
Technical Working Group, and the BAC Secretariat, the head of the Project
Management Office/Implementing Unit, and the project consultants by
consanguinity or affinity up to the third civil degree;
7. [Name of Bidder] complies with existing labor laws and standards;
8. [Name of Bidder] is aware of and has undertaken the following responsibilities

as a Bidder:
a) Carefully examine all of the Bidding Documents;
b) Acknowledge all conditions, local or otherwise, affecting the

implementation of the Contract;
96
Contract ID:
Contract Name:
c) Make an estimate of the facilities available and needed for the contract to
be bid, if any; and
d) Inquire or secure Supplemental/Bid Bulletin(s) issued for the [Name of the

Project]; and
9. [Name of Bidder] did not give or pay directly or indirectly, any commission,
amount, fee, or any form of consideration, pecuniary or otherwise, to any person
or official, personnel or representative of the government in relation to any
procurement project or activity.
IN WITNESS WHEREOF, I have hereunto set my hand this __ day of ___, 20__
at ____________, Philippines.
____________________________________
[Bidder’s Representative/Authorized Signatory]
SUBSCRIBED AND SWORN to before me this __ day of [month] [year] at [place

of execution], Philippines. Affiant/s is personally known to me and was identified by
me through competent evidence of identity in the 2004 Rules on Notarial Practice
(A.M. No. 02-8-13-SC). Affiant exhibited to me his/her [insert type of government
identification card used], with his/her photograph and signature appearing theron,
with no._______.
Witness my hand and seal this ____day of [month] [year].
NAME OF NOTARY PUBLIC

Serial no. of Commission_______
Notary Public for ____ until ____
Roll of Attorneys No. _______
PTR No.__, [date issued], [place issued]
IBP No.__, [date issued], [place issued]
Doc. No. ____

Page No. ____
Book No. ____
Series of ______.
97
Contract ID :
Contract Name :
Location of the Contract :
AFFIDAVIT AS TO COMPLIANCE OF SECTION 11 A-4

CONFLICT OF INTEREST
) S.S
I, , of legal age, married, Filipino, and residing at

, after having been duly sworn in accordance, with law, do hereby depose and state that:
I am the sole proprietor of with office address at

.
As the owner and sole proprietor of , I have full

authority to do, execute and perform any and all acts necessary to represent it in the bidding for
above mentioned contract of the DPWH.
complied to Section II A-4 of the Bidding

Documents, Conflict of Interest with another Bidder and general conflict of interest in any of the
following circumstances:
a) No controlling shareholders in common with another bidder;
b) Has not received any direct or indirect subsidy from any other bidder.
c) Has no legal representative, the same as that of another bidder for purposes of this
bid.
d) Has no relationship, directly through third parties, that puts them in a position to
have access to information about or influences on the bid of another bidder or
influence the decisions of the Procuring Entity regarding this bidding process.
e) Does not submit more than one bid in this bidding process.
f) Do not participate as a consultant in the preparation of the design or technical
specifications of the goods and related services that are subject to the bid;
g) Do not lends, or temporary seconds, its personnel to firms or organizations which are
engaged consulting services for the preparation related to procurement or
implementation of the project, the personnel would be involved in any capacity in the
same project.
IN WITNESS WHEREOF, I have hereunto set my hand this day of

at , Philippines.
Bidders Representative/Authorized Signatory
98
SUBSCRIBED AND SWORN to before me this day of at
, affiant exhibiting to me his Residence Certificate No. issued on
at .
Doc. No.
Page No. ___________________
Book No.
Series of
99
100

Bidding Docs

Uploaded by

Copyright:

Available Formats

Bidding Docs

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Bidding Docs

Uploaded by

Copyright:

Available Formats

Republic of the Philippines

DEPARTMENT OF PUBLIC WORKS AND HIGHWAYS

Contract ID No.: 17NI0057 (Re-ad)

Installation of the Structured Network Cabling and

October 25, 2017 at 8:00 A.M. to 10:00 A.M.

October 25, 2017 at 10:00 A.M.

SECTION I. INVITATION TO BIDERROR! BOOKMARK NOT DEFINED.

Republic of the Philippines

Contract ID: 17NI0057 (Re-ad)_

Contract ID: 17NI0057 (Re-ad)

Activity Time Place

CANDELARIO P. PORTILLO GERTRUDES S. CATIIL

Dates of Publication: ____N/A______________ CANDELARIO P. PORTILLO

3. Corrupt, Fraudulent, Collusive, and Coercive Practices

(i) "corrupt practice" means behavior on the part of officials

(ii) "fraudulent practice" means a misrepresentation of facts in

(iii) “collusive practices” means a scheme or arrangement

(iv) “coercive practices” means harming or threatening to

(v) “obstructive practice” is

(aa) deliberately destroying, falsifying, altering or

(c) will declare a firm ineligible, either indefinitely or for a stated

(a) A Bidder has controlling shareholders in common with another

(b) A Bidder receives or has received any direct or indirect subsidy

(c) A Bidder has the same legal representative as that of another

(d) A Bidder has a relationship, directly or through third parties, that

(f) A Bidder who participated as a consultant in the preparation of

(g) A Bidder who lends, or temporary seconds, its personnel to firms

(h) If the Bidder is an individual or a sole proprietorship, to the Bidder

(i) If the Bidder is a partnership, to all its officers and members;

(j) If the Bidder is a corporation, to all its officers, directors, and

Relationship of the nature described above or failure to comply with this

(a) Duly licensed Filipino citizens/sole proprietorships;

(c) Corporations duly organized under the laws of the Philippines,

(d) Cooperatives duly organized under the laws of the Philippines,

(e) Persons/entities forming themselves into a JV, i.e., a group of two

Government Corporate Entities may be eligible to participate only if they can

(b) For Foreign-funded Procurement, the Procuring Entity and the

The Bidder must submit a computation of its Net Financial

NFCC = [(Current assets minus current liabilities) (K)] minus the

The Bidder is responsible for the following:

(a) Having taken steps to carefully examine all of the Bidding

(b) Having acknowledged all conditions, local or otherwise, affecting

(c) Having made an estimate of the facilities available and needed

(d) Having complied with its responsibility to inquire or secure

(e) Ensuring that it is not “blacklisted” or barred from bidding by the

(f) Ensuring that each of the documents submitted in satisfaction of

(h) Ensuring that the signatory is the duly authorized representative

(i) Complying with the disclosure provision under Section 47 of the

(j) Complying with existing labor laws and standards, if applicable.

Failure to observe any of the above responsibilities shall be at the risk

It shall be the sole responsibility of the prospective bidder to determine and to

7. Origin of GOODS and Services

Subcontractors must submit the documentary requirements under ITB Clause

B. Contents of Bidding Documents

10. Clarification and Amendment of Bidding Documents

11. Language of Bids

12. Documents Comprising the Bid: Eligibility and Technical

(a) Eligibility Documents –

Dates of Publication: N/A__________ CANDELARIO P. PORTILLO