Determination of MR of Gas Butane 9.1.19

http://www.cpet.ufl.
edu/wp-content/uploads/2013/03/%E2%80%98Molar-Mass-of-a-Gas-
Determined-Experimentally%E2%80%99-Lab-Procedures-and-Worksheet.pdf
Molar mass of Butane LAB.doc
MOLAR MASS OF A GAS DETERMINED EXPERIMENTALLY
PRE-LAB DISCUSSION:
In this lab, we are going to determine the molar mass of butane, C4H10, experimentally. A simple
calculation using a periodic table would give us the correct answer for the molar mass of butane,
however, you are going to conduct an experiment in the lab to see how close you can come to
the accepted value. From Section 14.3 in the book, we know that PV = nRT. The ideal gas law
equation can be rearranged to solve for n, the number of moles:
n = PV
RT
We are trying to find the molar mass, which is expressed in units of grams per mole (g/mol). We
will measure the mass of the butane released from the pressurized container, and we will
measure the volume of the gas that we collect. You can use the method of water displacement at
room conditions and then substitute the measurements of volume, temperature, and pressure into
the ideal gas law equation in order to find n, the number of moles of butane. Once we know the
mass, and the number of moles, we will divide the mass by the number of moles to calculate the
molar mass (g/mol).
WARNING: Butane is a flammable gas, and at NO TIME during this lab should there be
any use of an open flame or other heat source!
QUESTION: What is the molar mass of butane? Butane is the gas used as fuel for a cigarette
lighter.
HYPOTHESIS: If we can capture a sample of gas and determine the mass of the sample and the
number of moles, then we can calculate the molar mass using the following equation:
Molar Mass = mass of sample in grams

number of moles
PROCEDURE:
1. Determine the initial mass for the butane lighter provided by your instructor ( +/- .01 gram ).
2. Set up the water basin for collecting a gas in an inverted graduated cylinder by water
displacement. Use a 100 mL graduated cylinder.
3. Release butane from the pressurized container and collect a sample of gas with a volume of
approximately 70.0 mL to 90.0 mL. Collect every bubble that leaves the lighter. If you
miss a bubble, you will have to repeat the entire procedure beginning with re-weighing the
clean and dry lighter.
4. Adjust the cylinder up or down so that the water level inside the graduated cylinder is the same
as the level outside the cylinder. THIS IS VERY IMPORTANT! If you miss this simple step,
the pressures inside and outside the cylinder will not be equal, and you will have an
inaccurate estimation of the pressure inside the cylinder where the gas is collected.
5. Record the volume of butane that was collected in the Observations and Data section.
6. Measure and record the temperature of the water in the basin ( +/- 0.1 °C ). This will be used
to determine the vapor pressure of water H2O (g) in the graduated cylinder.
(a Table of water vapor pressure at a given temperature is on the back)
7. Read the barometric pressure in the lab (inches of Hg ) and convert this to mm Hg (using the
conversion factor 1 inch Hg = 25.4 mm Hg) and then to kPa.
8. Make sure the lighter is dry then, measure and record the mass of it ( +/- .01 gram).
9. Clean and return all materials to the starting position for the next class.
10. Report your measurements and calculations on the class data sheet.
OBSERVATIONS AND DATA: Name _____________________ Group __________
This sheet will be turned in by each person at the end of the period for a lab grade.
Mass
1. Beginning mass of butane container (minitial ) _________________grams
2. Final mass of butane container (mfinal ) _________________grams
3. Mbutane = Mass of butane collected (line 1 – line 2) _________________grams
Volume
4. Volume of the gas collected _________________mL
5. Vbutane = Volume of butane, converted to liters (line 4 ÷ 1000) _________________L
Temperature
6. Temperature of water basin in °C _________________°C
7. Tbutane = Temperature of water in K _________________K
(we can assume the water temp = butane temp)
Pressure (READ the instructions below)

8. Barometric pressure in the room Proom __________in. Hg = Ptotal __________ mm Hg
9. Vapor pressure of water at the temperature in line 6

(see Table 1 attached) Pwater _______________mm Hg
Note: The gas collected in the cylinder is a mixture of C4H10 (g) and H2O (g).
Use Dalton’s Law of Partial Pressure to calculate the pressure of butane in the mixture.
Ptotal = P butane + P water vapor

10. Pressure of dry butane Pbutane _______________mm Hg
11. Convert Pbutane from mm Hg into kPa using the unit factor method.
SHOW your conversion below.
_________________________________________ = Pbutane _________________ kPa

Moles
1. Calculate the number of moles of butane collected using R = 8.31 kPa · L / mol · K
P= ___________ PV = nRT
V= ___________
n=
R= __________
Τ= ____________
n = __________
2. Calculate the experimental molar mass of butane by dividing the mass, M (line 3),
by n, the number of moles.
MM experimental = _________
3. Calculate the accepted value for the molar mass of butane using a periodic table.
Butane C4H10
MM accepted = ____________
4. Calculate the ERROR (the difference between the accepted value and your
experimental value).
5. Calculate the percentage error in your result.
% error __________
Bonus QUESTIONS:
1. How many grams of butane did you collect in this experiment?
2. What volume would the same number of grams of ethane (C2H6) have occupied at the
same conditions of temperature and pressure?

Determination of MR of Gas Butane 9.1.19

Uploaded by

Copyright:

Available Formats

Determination of MR of Gas Butane 9.1.19

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Determination of MR of Gas Butane 9.1.19

Uploaded by

Copyright:

Available Formats

http://www.cpet.ufl.

Molar Mass = mass of sample in grams

Pressure (READ the instructions below)

9. Vapor pressure of water at the temperature in line 6

Ptotal = P butane + P water vapor

SHOW your conversion below.

_________________________ = Pbutane _ kPa

5. Calculate the percentage error in your result.

You might also like