1st International Conference on Current Research in Engineering

(SIEICON-2017)
April 13, 2017
Sigma Institute of Engineering, Ajwa-Nimeta Road, Vadodara, Gujarat, India

Differential Current Protection of Transformer using Arduino with Voice

Alert
Patel Afzal1, Patel Jigar2, Tadvi Raj3, Khuman Abhishek4, Mr. Ketan Bariya5
1
B.E student, Electrical Engineering, Sigma Institute of Engineering, Vadodara
2
B.E student, Electrical Engineering, Sigma Institute of Engineering, Vadodara
3
B.E student, Electrical Engineering, Sigma Institute of Engineering, Vadodara
4
B.E student, Electrical Engineering, Sigma Institute of Engineering, Vadodara
5
Asst prof, Electrical Engineering, Sigma Institute of Engineering, Vadodara

Abstract- The main purpose of this project is to establish a differential protection of transformer and this is to
be done using arduino as brain, the current sensor measure current entering and leaving the transformer and
arduino decides when to disconnect the transformer according to the basis of difference of current.

Keywords-Transformers, Differential Current Protection, Arduino Board, Current Transformer.

I. INTRODUCTION

The faults of transformer in electrical power system are common problem. The faults occurs on the transformer
is mainly divided into two types external fault and internal fault , external fault are cleared by the relay system
outside the transformer within the shortest possible time to avoid any danger to the transformer due to these
faults. The Protection for internal faults in such type of transformer is to be provided by using differential
protection scheme. Differential protection scheme are mainly used for protection against phase to phase faults
and phase to earth faults. The differential protection used for power transformers is based on merz–prize
circulating current principle. Differential protection is not only limited to transformer but it is also used for
protection of utilities like generators, synchronous motor and bus bars.

II. DIFFERENTIAL CURRENT PROTECTION

Figure 1.Differential Current Protection of Transformer [3]

During the external(normal load condition) condition, the current entering and leaving in the protected
winding(equipment) will be same in magnitude and phase relation, Therefore instantaneous values of CT
secondary currents will be same at all instants. This obviously, means that the current through relay will be zero
and the relay will not operate. During internal fault condition the currents entering and leaving in the protected
winding will not be in same magnitude and phase relation. Therefore the CT secondary currents are disturbed.
Hence, the differential or spill current will through the relay. If this current is higher than the set value of the
relay, relay will operate and isolate the protected equipment from the system.

@SIEICON-2017, All rights Reserved 1

1st International Conference on Current Research in Engineering (SIEICON-2017)
April 13, 2017

III. ARDUINO

Arduino is hardware and software company, Arduino is similar to microcontrollers. These systems provide sets
of digital and analog input/output (I/O) pins that can connected to various board and other circuits. The boards
most feature of serial communication interfaces, including Universal Serial Bus (USB) on some models, and
also loading programs from computers. For programming the microcontrollers, the arduino project provides an
integrated development environment (IDE) based on a programming language name like: C and C++. Also
ardiuno provide another feature of a low cost, easily available, not effect to environment, this is the Main aim to
choose arduino another feature is that it is the portable USB connected.

Figure 2. Arduino UNO Board [5]

IV. CIRCUIT DIAGRAM

@SIEICON-2017, All rights Reserved 2

1st International Conference on Current Research in Engineering (SIEICON-2017)
April 13, 2017

Figure 3.Circuit Diagram in Proteus Design Suite

V. WORKING

Arduino is the main component in this circuit. Above figure shows the circuit diagram of the differential
protection of transformer using arduino with voice announcement. Here arduino is used to compare the currents
on both primary and secondary. Two rectifier circuits are used in this circuit to convert the AC voltage into DC
voltage for the use of arduino. Current transformers also provided one on primary and another on secondary to
tap the currents on both sides and to give proportionate voltage to the rectifier circuits. Output of the arduino is
connected to the relay. The relay here is 12V DC 1-phase relay. Relay is used to initiate the voice circuit which
gives voice alert.

Under normal operating conditions currents on primary and secondary are same. So, the proportionate voltages
generated by the current transformers on primary and secondary are same. These two voltages will give to the
arduino. The proportionate voltages generated by current transformers are rectified by the rectifiers in the circuit.
Under normal operating conditions these two voltages will be same in magnitude and difference is zero. So, the
arduino gives no signal to the relay.

Whenever extra load or an internal fault occur in transformer the currents seen by the CT on primary and
secondary differs by same amount. As a result voltage sensed by the arduino from primary and secondary
differs. As there is a difference in the voltage sensed by the arduino i.e., difference is not zero. Arduino give a
signal to the relay according predefined program. As and when the relay is activated by the arduino the relay
will activates the voice announcement circuit. The voice circuit will give output predefined voice as a alert to the
operator. After three consecutive voice alerts Arduino will give trip signal to the relay board and which is
connected in series with the supply will open its contacts thus the supply to the hardware setup will be
disconnected.

VI. SOFTWARE

@SIEICON-2017, All rights Reserved 3

1st International Conference on Current Research in Engineering (SIEICON-2017)
April 13, 2017

Figure 4.Flow Chart of Arduino Programming

ARDUINO PIN ASSIGNED FOR FUNCTIONS.

sensorPin1 = A0;
sensorPin2 = A1;
x’merPin = 13;
buzzerPin=12;
VII. PROTEUS SIMULATION

6.1 Simulation While Both Currents Are Same:-

@SIEICON-2017, All rights Reserved 4

1st International Conference on Current Research in Engineering (SIEICON-2017)
April 13, 2017

Figure 5. Simulation While Both Currents Same

Figure shows the Proteus simulation of Differential Current Protection of transformer using Arduino with voice
alert, when the both currents are same the lamp which is connected to transformer is ON. We can say this is
normal working condition of transformer

6.2 Simulation While Both Currents Are Different:-

Figure 6. Simulation While Both Currents are Different

Figure shows the Proteus simulation of Differential Current Protection of transformer using Arduino with voice
alert, when the value of both currents is different to each other the BUZZER is ON. We can say this is Abnormal
working condition of transformer.

VIII. HARDWARE IMPLEMNTATION

List of Components Used For This Project

@SIEICON-2017, All rights Reserved 5

1st International Conference on Current Research in Engineering (SIEICON-2017)
April 13, 2017

1. Current Transformers
2. Potential Transformer
3. Capacitor
4. Diode (1N4733A)
5. OP Amplifier (LM358)
6. Relay
7. Resistors
8. Transistor (BC547)
9. Buzzer

Figure 7. Hardware of the Project

VII. CONCLUSION

From this project we have concluded that when internal fault occurs and the value of both currents are different
the relay gets operated and the voice circuit gives voice alert by the sense of arduino, so we come to know about
abnormal working condition of transformer. Therefore by using Differential protection scheme, transformer is
protected from faults with the use of Arduino operating an electromagnetic relay.

REFERENCES

1) Sarfaraz Nawaz saiyed, S. Radhika, M.N Sandhya Rani, “Differential Current Protection of
Transformer using Arduino with Voice Alert”, International Journal of Innovations in Engineering and
Technology (IJIET) ,Volume 6, pp. 206-212, 2nd December 2015, ISSN: 2319-1058.
2) Adil Naseem, Naveed Alam, “Protection of distribution transformer Using Arduino plat
form,Sci.Int.(Lahore),27(1),403-406,2015 in ISSN 1013-5316.
3) Switchgear And Protection – S. S. Rao, Khanna publication.
4) Power system protection and switchgear by Oza, Nair, Mehta, Makwana, Mc Graw Hill publication.
5) Power Electronics byP.S.Bhimbhra, Khanna publication.
6) Computer relaying for power systems by A.G.Phadke, J.S.Thorp-research studies press ltd. England
John Wiley & sons Inc. New York.
7) A Web Course on Digital protection of power system by Prof. Dr. S.A.Soman, IIT Bombay
8) Power System Protection – B. Ram, TMH Publication.
9) Arduino.cc
10) https://www.labcenter.com

@SIEICON-2017, All rights Reserved 6