Ge Converteam mv3000 Ferrite Install

Download as pdf or txt
Download as pdf or txt
You are on page 1of 4

ALSPA MV3000e FERRITE ASSEMBLY

Part Number MV3FLT140B6A1

Features / Specifications :
• Assists in compliance of drives with EMC emission
requirements.
• Suitable for use with drives rated up to 140 A.
• Suitable for up to 690 V.

WARNING
Surfaces on the ferrite assembly can reach high temperatures.

Box Contents
Ferrite Assembly (MV3FLT140B6A1).
Two M5 taptite screws (for fixing the bracket to metal enclosure).
This Instruction Sheet (T1921EN).

Related Documents
T1676 MV3000 Getting Started Manual.

Instruction Sheet T1921EN Rev. 0006 (02/07)


Page 1 of 4
Commissioning
1) Position Assembly immediately below drive (allowing for the bend radius of cables).

2) If you wish to use the screws supplied, drill two 4.5 mm diameter holes suitable for Aluminium or Steel
1.0 to 3.5 mm (0.039 to 0.137 inch) thick. Alternatively the installer may supply M5 or No 10 screws
and drill holes to suit.
Note : The ferrite assembly must be attached to the same metal mounting panel as the drive.

3) Pass all 3 phases of the motor cable through inner hole of the
Ferrite Assembly. DO NOT pass earth (ground) wires or
armours through this hole. In some applications, the
temperature of the ferrite assembly can rise by 70 °C (126 °F)
above ambient. Therefore the cables should either have the
appropriate temperature rating or be routed so that they do not
touch the ferrite cores.

4) Cable screen (shield) armour or metal conduits should be


connected directly to the metal enclosure to which the drive is
mounted.

56.0 (2.2")
6.0 (0.24")Dia
Internal

`
12.0 (0.47") Dia

52.9 (2.1")
48.4 (1.9") 57.4 (2.3")

67.0 (2.6")

86.9 (3.4") 110.5 (4.3")

117.0 (4.6")

139.0 (5.5")

Customer Services
Please refer to your local technical support centre if you have any queries about this product.

Instruction Sheet T1921EN Rev. 0006 (02/07)


Page 2 of 4
ALSPA MV3000e FERRITE ASSEMBLY

This Page Intentionally Left Blank

Instruction Sheet T1921EN Rev. 0006 (02/07)


Page 3 of 4
The logo Converteam and their frameworks are trademarks and service trademark applications of Converteam
Converteam

France
9, rue Ampère
91345 Massy Cedex
Sales Tel: +33 (0) 8 25 02 11 02
Support Tel (International):
+33 (0) 3 84 55 33 33
Support Tel. (National):
08 25 02 11 02

Germany
Culemeyerstraße 1
D-12277 Berlin
Sales Tel: +49 (0) 30 74 96 27 27
Support Tel (International):
+49 (0) 69 66 99 831
Support Tel (National):
01 80 3 23 45 72
© Converteam UK Ltd - 2007 - Publication No. T1921EN.

UK
Boughton Road, Rugby
Warwickshire, CV21 1BU
Sales Tel: +44 (0) 1788 563625
Support Tel: +44 (0) 1788 547490

USA
610 Epsilon Drive
Pittsburgh, PA 15238
Sales Tel: +1 412 967 0765
Support Tel: +1 800 800 5290

Instruction Sheet T1921EN Rev. 0006 (02/07)


Page 4 of 4

You might also like