User Manual for SGT8000A

V2.1
 Contents
1 PON Function Configuration....................................................................................................6

1.1 PON Management Function Configuration ......................................................................6

1.1.1 ont-find ......................................................................................................................6

1.1.2 ont-find list-age .........................................................................................................7

1.1.3 show ont-find config..................................................................................................7

1.1.4 show ont-find list .......................................................................................................8

1.1.5 show dba-map ...........................................................................................................9

2 Service Deployment Configuration........................................................................................10

2.1 Service Deployment Management .................................................................................10

2.1.1 deploy operation-permission request .....................................................................10

2.1.2 deploy operation-permission release......................................................................11

2.1.3 deploy operation-permission release-by-force .......................................................11

2.1.4 deploy profile vlan ...................................................................................................12

2.1.5 deploy profile us-traffic ...........................................................................................12

2.1.6 deploy profile ds-traffic ...........................................................................................13

2.1.7 deploy profile dba ...................................................................................................13

2.1.8 deploy profile line....................................................................................................13

2.1.9 deploy profile unique ..............................................................................................14

2.1.10 deploy profile rule .................................................................................................14

2.1.11 aim .........................................................................................................................15

2.1.12 delete.....................................................................................................................15

2.1.13 exit .........................................................................................................................16

2.1.14 deploy clear ...........................................................................................................16

2.1.15 deploy rebuild........................................................................................................17

2.1.16 deploy active .........................................................................................................17

2.1.17 show deploy active-domain ..................................................................................18

2.1.18 show deploy inactive-domain ...............................................................................24

2.1.19 show deploy difference .........................................................................................29

 2.1.20 show deploy match ...............................................................................................31

2.1.21 show deploy affect ................................................................................................32

2.1.22 show deploy status ................................................................................................33

2.1.23 show deploy history ..............................................................................................34

2.2 VLAN Profile Configuration.............................................................................................35

2.2.1 translate...................................................................................................................35

2.2.2 add ...........................................................................................................................36

2.2.3 default .....................................................................................................................36

2.3 Us-traffic Profile Configuration ......................................................................................37

2.3.1 us .............................................................................................................................37

2.4 Ds-traffic Profile Configuration.......................................................................................38

2.4.1 ds .............................................................................................................................38

2.5 DBA Profile Configuration ..............................................................................................38

2.5.1 type ..........................................................................................................................38

2.6 Line Profile Configuration ...............................................................................................39

2.6.1 device type ..............................................................................................................40

2.6.2 tcont ........................................................................................................................40

2.6.3 gemport ...................................................................................................................41

2.6.4 mapping ...................................................................................................................42

2.6.5 flow ..........................................................................................................................43

2.6.6 mac-address-table max-mac-count .........................................................................44

2.6.7 multicast mode ........................................................................................................44

2.6.8 multicast group-limit ...............................................................................................45

2.6.9 multicast us-tag .......................................................................................................45

2.6.10 multicast ds-tag .....................................................................................................46

2.6.11 multicast program .................................................................................................47

2.6.12 multicast fast-leave disable ...................................................................................48

2.6.13 local shutdown ......................................................................................................48

2.6.14 local flow-control...................................................................................................48

2.6.15 local bandwidth egress ..........................................................................................49

 2.6.16 local loop-detect ....................................................................................................49

2.6.17 local switch ............................................................................................................50

2.6.18 local catv-agc .........................................................................................................50

2.7 Unique Profile Configuration ..........................................................................................51

2.7.1 description ...............................................................................................................51

2.7.2 tcont ........................................................................................................................51

2.7.3 gemport ...................................................................................................................52

2.7.4 sip agent ..................................................................................................................53

2.7.5 sip user ....................................................................................................................53

2.7.6 sip digitmap .............................................................................................................54

2.8 Rule Profile Configuration ..............................................................................................54

2.8.1 permit ......................................................................................................................54

3 ONT Management Function ..................................................................................................56

3.1 ONT Information Query ..................................................................................................56

3.1.1 show ont optical-info...............................................................................................56

3.1.2 show ont statistics ...................................................................................................57

3.1.3 show ont port-status ...............................................................................................58

3.1.4 show ont multicast ..................................................................................................59

3.1.5 show ont info ...........................................................................................................60

3.1.6 show ont brief .........................................................................................................61

3.1.7 show ont description ...............................................................................................63

3.1.8 show ont profile ......................................................................................................63

3.1.9 show ont upgrade-status.........................................................................................65

3.2 ONT Remote Management.............................................................................................66

3.2.1 ont reboot................................................................................................................66

3.2.2 ont upgrade .............................................................................................................67

3.3 ONT Logging Management .............................................................................................68

3.3.1 ont-logging...............................................................................................................68

3.3.2 ont-logging buffer ....................................................................................................69

3.3.3 ont-logging monitor.................................................................................................69

3.3.4 ont-logging prefix ....................................................................................................70

3.3.5 ont-logging timestamps ...........................................................................................70

3.3.6 show ont-logging config ..........................................................................................71

3.3.7 show ont-logging buffer ..........................................................................................72

3.3.8 clear ont-logging buffer ...........................................................................................72

1 PON Function Configuration
1.1 PON Management Function Configuration

 ont-find

 ont-find list-age

 show ont-find config

 show ont-find List

 show dba-map

1.1.1 ont-find

This command is used to enable ONT discovery function. The ONT will be discovered every

polling interval. The polling interval can be configed.If not, the polling interval will be set to the

default value. The default polling interval is 10 seconds. This function is disabled by default.

ont-find [ interval-time <interval_time> ] interface gpon { <interface_list> | all }

no ont-find Interface gpon { <interface_list> | all }

【Parameter Specification】

Interval_time: Polling interval in seconds, in the range of 3 to 30 seconds

Interface_list: GPON port list, representing multiple GPON ports. The port number is

represented as slot_num / port_num, slot_num is the slot number, and port_num is the port

number in the slot. Consecutive ports are connected with a minus sign, and non-contiguous ports

are separated by commas, such as: 0 / 1-0 / 5,0 / 8

All: All GPON ports

【Usage】

Global configuration mode

【Example】

Enable ONT discovery on GPON port 0/1 and set the polling interval to 5 seconds

GPON (config) # ont-find interval-time 5 interface gpon 0/1

1.1.2 ont-find list-age

This command is used to enable aging function of the ONT discovery list. You can configure

the aging time for the ONT discovery list at the same time. If not, the aging time will be set to the

default value. The default aging time is 300 seconds. This function is disabled by default. ONT

discovery list is used to record the ONT's SN that has been reported to, but not certified by the

OLT. When an ONT in the list passes the authentication, the system deletes its SN from the list.

ont-find list-age [time <aging_time>] Interface gpon {<interface_list> | all}

no ont-find list-age interface gpon {<interface_list> | all}

【Parameter Specification】

Aging_time: ONT aging time in the discovery list, in the range of <1-86400>

Interface_list: GPON port list, representing multiple GPON ports. The port number is

represented as slot_num / port_num, slot_num is the slot number, and port_num is the port

number in the slot. Consecutive ports are connected with a minus sign, and non-contiguous ports

are separated by commas, such as: 0 / 1-0 / 5,0 / 8

All: All GPON ports

【Usage】

Global configuration mode

【Example】

Enable the ONT discovery list aging function on GPON port 0/1 and set the aging time to

500 seconds.

GPON (config) # ont-find list-age time 500 interface gpon 0/1

1.1.3 show ont-find config

This command is used to check the configuration of the ONT discovery function: discovery

function on/off status, discovery polling interval, discovery list aging function on/off status and

discovery list aging time.

show ont-find Config interface gpon {<interface_list> | all}

【Parameter Specification】
 Interface_list: GPON port list, representing multiple GPON ports. The port number is

represented as slot_num / port_num, slot_num is the slot number, and port_num is the port

number in the slot. Continuous ports can be connected with a minus sign, with non-contiguous

ports separated by commas, such as: 0 / 1-0 / 5,0 / 8

All: Specifies all GPON ports

【Usage】

All modes

【Example】

Check the ONT discovery configuration of GPON port 0/1

GPON (config) # show ont-find Config interface gpon 0/1

Port Find Find-interval Age Aging-time

P0 / 1 enable 300 disable -

1.1.4 show ont-find list

This command is used to check the details of the ONT discovery list on the OLT.

show ont-find list {interface gpon {<interface_list> | all} | sn {string-hex <sn_num> | hex

<sn_num>}}

Show ont-find list interface gpon <interface_num> index <index_num>

【Parameter Specification】

Interface_list: GPON port list, representing multiple GPON ports. The port number is

represented as slot_num / port_num, slot_num is the slot number, and port_num is the port

number in the slot. Continuous ports can be connected with a minus sign, with non-contiguous

ports separated by commas, such as: 0 / 1-0 / 5,0 / 8

All: Specifies all GPON ports

Interface_num: GPON port number. The port number is represented as slot_num / port_num,

slot_num is the slot number, port_num is the port number in the slot

Index_num: ONT discovery list index, in the range of 0-255

sn_num: the physical identification of the ONT. There are two formats:

string-hex format: STRING <13-13>, the first four string is character, then '-' behind, after
that is 8 hexadecimal number, use the "*" matches the corresponding bit of all characters or

hexadecimal numbers;

hex format: STRING <16-16>, all the bits are in hexadecimal number, use the "*" matches

the corresponding bit of all characters or hexadecimal numbers

【Usage】

All modes

【Example】

Check the ONT discovery list on GPON port 0/1

GPON (config) #show ont-find list interface gpon 0/1

Port Index SN Last-find Find-cnt

P0 / 1 0 GCOM-13079998 2001-04-14 23:54:52 1

Total entries: 1.

1.1.5 show dba-map

This command is used to check the upstream bandwidth allocation of the specified GPON

port.

show dba-map interface gpon <interface_num>

【Parameter Specification】

Interface_num: GPON port number. The port number is represented as slot_num / port_num,

slot_num is the slot number, port_num is the port number in the slot

【Usage】

All modes

【Example】

Display the uplink bandwidth usage of PON port 0/1

GPON (config) #show deploy profile-dba bandwidth gpon 0/1

ONT Tcont DBA-index Fixed Assured Max

1 1 30 4096 0 4096

Total entries: 1.

Total: fixed 4096kbps, assured 0kbps, max 4096kbps.

2 Service Deployment Configuration
2.1 Service Deployment Management

 deploy operation-permission request

 deploy operation-permission release

 deploy operation-permission release-by-force

 deploy profile auth

 deploy profile dba

 deploy profile line

 deploy profile unique

 deploy profile rule

 aim

 delete

 exit

 deploy clear

 deploy rebuild

 deploy active

 show deploy active-domain

 show deploy inactive-domain

 show deploy difference

 show deploy match

 show deploy affect

 show deploy status

 show deploy history

2.1.1 deploy operation-permission request

This command is used to apply for service deployment permission. Only the user having the

deployment permission can deploy the PON service. Deployment permission can only be acquired
by one user at one time, and other users could get deployment permission when the user actively

or compulsively releases the deployment permission.

deploy operation-permission request

【Parameter Specification】

no

【Usage】

Global configuration mode

【Example】

Gets the deployment permission

GPON (config) # deploy operation- permission request

2.1.2 deploy operation-permission release

This command is used to release service deployment permission. The user who release the

deployment permission will be unable to deploy any PON service.

deploy operation-permission release

【Parameter Specification】

no

【Usage】

Global configuration mode

【Example】

Release the service deployment configuration permission.

GPON (config) # deploy operation- permission release

2.1.3 deploy operation-permission release-by-force

This command is used to force the current user to release deployment permission. This

command is only available to admin user.

deploy operation-permission release-by-force

【Parameter Specification】

no
【Usage】

Debug mode

【Example】

GPON (diag) %% deploy operation- permission release-by-force

2.1.4 deploy profile vlan

This command is used to enter the configuration mode of the vlan profile.

deploy profile vlan

【Parameter Specification】

no

【Usage】

Global configuration mode

【Example】

Enter the vlan profile configuration mode

GPON (config) #deploy profile vlan

GPON (deploy-profile-vlan) #

2.1.5 deploy profile us-traffic

This command is used to enter the configuration mode of the upstream traffic profile.

deploy profile us-traffic

【Parameter Specification】

no

【Usage】

Global configuration mode

【Example】

Enter the upstream traffic profile configuration mode

GPON (config) #deploy profile us-traffic

GPON (deploy-profile-us-traffic) #
2.1.6 deploy profile ds-traffic

This command is used to enter the configuration mode of the downstream traffic profile.

deploy profile ds-traffic

【Parameter Specification】

no

【Usage】

Global configuration mode

【Example】

Enter the downstream traffic profile configuration mode

GPON (config) #deploy profile ds-traffic

GPON (deploy-profile-ds-traffic) #

2.1.7 deploy profile dba

This command is used to enter the DBA profile configuration mode.

deploy profile dba

【Parameter Specification】

no

【Usage】

Global configuration mode

【Example】

Enter the DBA profile configuration mode

GPON (config) #deploy profile dba

GPON (deploy-profile-dba) #

2.1.8 deploy profile line

This command is used to enter the service profile configuration mode. .

deploy profile line

【Parameter Specification】
 no

【Usage】

Global configuration mode

【Example】

Enter service profile configuration mode

GPON (config) #deploy profile line

GPON (deploy-profile-line) #

2.1.9 deploy profile unique

This command is used to enter the special function profile configuration mode.

deploy profile unique

【Parameter Specification】

no

【Usage】

Global configuration mode

【Example】

Enter the special function profile configuration mode

GPON (config) #deploy profile unique

GPON (deploy-profile-unique) #

2.1.10 deploy profile rule

This command is used to enter the rule profile configuration mode.

deploy profile rule

【Parameter Specification】

no

【Usage】

Global configuration mode

【Example】

Enter the rule profile configuration mode

 GPON (config) #deploy profile rule

GPON (deploy-profile-rule) #

2.1.11 aim

This command is used to enter into the configuration mode of profile entry. The index and

name of this entry will be given at the same time entering this mode.For the rule and unique

profile, the entry should be configured based on ONT ID.

aim { <index_num> [ name <name> ] | name <name> }

aim <ont_id> [ name <name> ]

【Parameter Specification】

index_num: the index of the profile entry, the range is <0-(M-1)>, M is the maximum ONTs

supported by the OLT

name: the name of the profile entry, combined with a string, and the range of the length is

<1-128>

ont_id: ONT ID number, in the form slot_num / port_num / ont_num, slot_num is the slot

number, port_num is the port number, ont_num is the ONT's index assigned by the OLT

【Usage】

The related profile configuration mode

【Example】

Create a vlan profile entry, the index is 100 and the name is Internet

GPON (deploy-profile-vlan) #aim 100 name Internet

GPON (deploy-profile-vlan-100) #

2.1.12 delete

This command deletes one or more specified profile entries.For the rule and unique profile,

the entry should be deleted based on ONT ID.

delete aim { <index_list> | name <name> }

delete aim { <ont_id_list> | name <name> }

【Parameter Specification】

index_list: entry index number combination, representing multiple entries. The range of

individual index numbers ranges from <0-(M-1)>, M is the maximum ONTs supported by the

OLT

name: the name of the profile entry, combined with a string, and the range of the length is

<1-128>

ont_id_list: the list of ONT IDs. Such as 0/1 / 1-0 / 2 / 5,0 / 2/10

【Usage】

The related profile configuration mode

【Example】

Delete the line profile entries with indexes between 101 and 200

GPON (deploy-profile-line) #delete aim 101-200

2.1.13 exit

This command is used to exit the service deployment profile and the profile entry

configuration mode, and return to the upper level command line mode.

exit

【Parameter Specification】

no

【Usage】

The related profile or profile entry configuration mode

【Example】

Exit the vlan profile configuration mode and return to the global configuration mode

GPON (deploy-profile-vlan) #exit

GPON (config) #

2.1.14 deploy clear

This command is used to clear the service deployment configuration of the inactive

area. After using this command, the service deployment configuration in the inactive area will be
cleared but that in the active area will not be affected.

deploy clear

【Parameter Specification】

no

【Usage】

Global configuration mode

【Example】

Clear the service deployment configuration in the inactive area

GPON (config) # deploy clear

2.1.15 deploy rebuild

This command is used to rebuild the service deployment configuration in the inactive

area. After using this command, the system deletes the configuration in the inactive area, and then

copies the configuration in the active area to the inactive area, which enables the user to make

configuration changes based on the existing configuration.

deploy rebuild

【Parameter Specification】

no

【Usage】

Global configuration mode

【Example】

Copies the configuration in the active area to the inactive area

GPON (config) # deploy rebuild

2.1.16 deploy active

This command is used to enable service deployment configuration in the inactive area. After

using this command, the system clears the configuration in the active area, and then copies the

configuration in the inactive area to the active area , then the configuration will be taken into

effect.
 deploy active

【Parameter Specification】

no

【Usage】

Global configuration mode

【Example】

Enable the inactive area service deployment configuration

GPON (config) # deploy active

2.1.17 show deploy active-domain

This command displays the service deployment configuration in the active area.

show deploy active-domain statistic

show deploy active-domain vlan brief { <index_list> | all }

show deploy active-domain vlan { <index_num> | name <name>}

show deploy active-domain us-traffic brief { <index_list> | all }

show deploy active-domain us-traffic { <index_num> | name <name>}

show deploy active-domain ds-traffic brief { <index_list> | all }

show deploy active-domain ds-traffic { <index_num> | name <name>}

show deploy active-domain dba brief { <index_list> | all }

show deploy active-domain dba { <index_num> | name <name>}

show deploy active-domain line brief { <index_list> | all }

show deploy active-domain line { <index_num> | name <name>}

show deploy active-domain rule brief { <ont_id_list> | all }

show deploy active-domain rule { <ont_id> | name <name>}

show deploy active-domain unique brief { <ont_id_list> | all }

show deploy active-domain unique { <ont_id> | name <name>}

【Parameter Specification】

index_list: entry index number combination, representing multiple entries. The range of

individual index numbers ranges from <0-(M-1)>, M is the maximum ONTs supported by the
OLT

index_num: the index of the profile entry, the range is <0-(M-1)>, M is the maximum ONTs

supported by the OLT

name: the name of the profile entry, combined with a string, and the range of the length is

<1-128>

all: Specifies all profile entries

ont_id: ONT ID number, in the form slot_num / port_num / ont_num, slot_num is the slot

number, port_num is the port number, ont_num is the ONT's index assigned by the OLT

ont_id_list: the list of ONT IDs. Such as 0/1 / 1-0 / 2 / 5,0 / 2/10

【Usage】

All modes

【Example】

Check the statistics of the profile entry configuration in the active area

GPON (config) # show deploy active-domain statistic

Profile Spec Config Reference

VLAN 1024 11 5

US-Traffic 1024 11 5

DS-Traffic 1024 11 5

DBA 1024 5 1

Line 1024 5 1

Rule 1024 5 1

Unique 1024 - -

Check the brief information of the vlan profile in the active area

GPON(config)#show deploy inactive-domain vlan brief all

Index : 0

Name : c100s2

Referenced by line : -

Referenced by unique : -

---------------------------------------------------------------------------

Index :1
Name ：fghij

Referenced by line : -

Referenced by unique : -

---------------------------------------------------------------------------

Total entries: 2.

Check the detail information of the vlan profile in the active area

GPON(config)# show deploy active-domain vlan 0

aim 0 name abcde

translate old-vlan 100 1 new-vlan 200 3

Check the brief information of the us-traffic profile in the active area

GPON(config)# show deploy active-domain us-traffic brief all

Index: 0

Name：abcde

Mode: queue

Referenced by line: -

Referenced by unique: -

---------------------------------------------------------------------------

Index: 1

Name：fghij

Mode: car

Referenced by line: -

Referenced by unique: -

---------------------------------------------------------------------------

Check the detail information of the us-traffic profile in the active area

GPON(config)# show deploy active-domain us-traffic 0

aim 0 name abcde

us queue 1

Check the brief information of the ds-traffic profile in the active area

GPON(config)# show deploy active-domain ds-traffic brief all

Index: 0
Name：abcde

Referenced by line: -

Referenced by unique: -

---------------------------------------------------------------------------

Index: 1

Name：fghij

Referenced by line: -

Referenced by unique: -

---------------------------------------------------------------------------

Check the detail information of the ds-traffic profile in the active area

GPON(config)# show deploy active-domain ds-traffic 0

aim 0 name abcde

ds car bandwidth 10000

Check the brief information of the DBA profile in the active area

GPON(config)# show deploy active-domain dba brief all

Index: 0

Name:abcde

Type: 1

Referenced by Line: -

---------------------------------------------------------------------------

Index: 1

name:fghij

Type: 2

Referenced by Line: -

---------------------------------------------------------------------------

Total entries: 2.

Check the detail information of the DBA profile in the active area

GPON(config)# show deploy active-domain dba 0

aim 0 name abcde

type 1 fix 10240

Check the brief information of the line profile in the active area

GPON(config)# show deploy active-domain line brief all

Index: 0

name:abcde

Device type:n20-100

Referenced by Rule: -

---------------------------------------------------------------------------

Index: 1

name:fghij

Device type: n20-400

Referenced by Rule: -

---------------------------------------------------------------------------

Total entries: 2.

Check the detail information of the line profile in the active area

GPON(config)# show deploy active-domain line 0

aim 0 name abcde

device type n20-100

tcont 1 profile dba index 1

gemport traffic-mode queue

gemport 1 tcont 1

gemport 2 tcont 1

gemport 3 tcont 1

mapping mode port-vlan-priority

mapping 1 vlan 1 priority 0 port eth 1 gemport 1

mapping 2 vlan 100 priority 0 port eth 1 gemport 2

mapping 3 vlan 200 priority 0 port eth 1 gemport 3

flow 1 port eth 1 default vlan 1 0

flow 2 port eth 1 cvlan 100 0 keep

multicast us-tag add 200 0 port 1

multicast ds-tag remove port 1

Check the brief information of the rule profile in the active area

GPON(config)# show deploy active-domain rule brief all

ONT : 0/1/1

Name:abcde

Reference Line: 0

---------------------------------------------------------------------------

ONT : 0/1/2

Name:fghij

Reference Line: -

---------------------------------------------------------------------------

Check the detail information of the rule profile in the active area

GPON(config)# show deploy active-domain rule 0/1/1

aim 0/1/1 name abcde

permit sn string-hex GPON-12345678 line 1 default line 1

Check the brief information of the unique profile in the active area

GPON(config)# show deploy active-domain unique brief all

ONT: 0/1/1

Name:abcde

---------------------------------------------------------------------------

ONT: 0/1/2

Name:fghij

---------------------------------------------------------------------------

ONT: 0/1/3

Name:aswq

---------------------------------------------------------------------------

Total entries: 3.

Check the detail information of the unique profile in the active area

GPON(config)# show deploy active-domain unique 0/1/1

aim 0/1/1 name abcde

gemport 1 vlan-profile 1 us-traffic-profile 1 ds-traffic-profile 1

 sip proxy server primary ip 192.168.2.100 signal port 6666

sip user 1 name admin password 123456 telno 10000

2.1.18 show deploy inactive-domain

This command displays the service deployment configuration in the inactive area.

show deploy inactive-domain statistic

show deploy inactive-domain vlan brief { <index_list> | all }

show deploy inactive-domain vlan { <index_num> | name <name>}

show deploy inactive-domain us-traffic brief { <index_list> | all }

show deploy inactive-domain us-traffic { <index_num> | name <name>}

show deploy inactive-domain ds-traffic brief { <index_list> | all }

show deploy inactive-domain ds-traffic { <index_num> | name <name>}

show deploy inactive-domain dba brief { <index_list> | all }

show deploy inactive-domain dba { <index_num> | name <name>}

show deploy inactive-domain line brief { <index_list> | all }

show deploy inactive-domain line { <index_num> | name <name>}

show deploy inactive-domain rule brief { <ont_id_list> | all }

show deploy inactive-domain rule { <ont_id> | name <name>}

show deploy inactive-domain unique brief { <ont_id_list> | all }

show deploy inactive-domain unique { <ont_id> | name <name>}

【Parameter Specification】

index_list: entry index number combination, representing multiple entries. The range of

individual index numbers ranges from <0-(M-1)>, M is the maximum ONTs supported by the

OLT

index_num: the index of the profile entry, the range is <0-(M-1)>, M is the maximum ONTs

supported by the OLT

name: the name of the profile entry, combined with a string, and the range of the length is

<1-128>

all: Specifies all profile entries

 ont_id: ONT ID number, in the form slot_num / port_num / ont_num, slot_num is the slot

number, port_num is the port number, ont_num is the ONT's index assigned by the OLT

ont_id_list: the list of ONT IDs. Such as 0/1 / 1-0 / 2 / 5,0 / 2/10

【Usage】

All modes

【Example】

Check the statistics of the profile entry configuration in the inactive area

GPON (config) # show deploy active-domain statistic

Profile Spec Config Reference

VLAN 1024 11 5

US-Traffic 1024 11 5

DS-Traffic 1024 11 5

DBA 1024 5 1

Line 1024 5 1

Rule 1024 5 1

Unique 1024 - -

Check the brief information of the vlan profile in the inactive area

GPON(config)# show deploy inactive-domain vlan brief all

Index: 0

Name：abcde

Referenced by line: -

Referenced by unique: -

---------------------------------------------------------------------------

Index: 1

Name：fghij

Referenced by line: -

Referenced by unique: -

---------------------------------------------------------------------------

Total entries: 2.

Check the detail information of the vlan profile in the inactive area
GPON(config)# show deploy inactive-domain vlan 0

aim 0 name abcde

translate old-vlan 100 1 new-vlan 200 3

Check the brief information of the us-traffic profile in the inactive area

GPON(config)# show deploy inactive-domain us-traffic brief all

Index: 0

Name：abcde

Mode: queue

Referenced by line: -

Referenced by unique: -

---------------------------------------------------------------------------

Index: 1

Name：fghij

Mode: car

Referenced by line: -

Referenced by unique: -

---------------------------------------------------------------------------

Check the detail information of the us-traffic profile in the inactive area

GPON(config)# show deploy inactive-domain us-traffic 0

aim 0 name abcde

us queue 1

Check the brief information of the ds-traffic profile in the inactive area

GPON(config)# show deploy inactive-domain ds-traffic brief all

Index: 0

Name：abcde

Referenced by line: -

Referenced by unique: -

---------------------------------------------------------------------------

Index: 1

Name：fghij
Referenced by line: -

Referenced by unique: -

---------------------------------------------------------------------------

Check the detail information of the ds-traffic profile in the inactive area

GPON(config)# show deploy inactive-domain ds-traffic 0

aim 0 name abcde

ds car bandwidth 10000

Check the brief information of the DBA profile in the inactive area

GPON(config)# show deploy inactive-domain dba brief all

Index: 0

Name:abcde

Type: 1

Referenced by Line: -

---------------------------------------------------------------------------

Index: 1

Name:fghij

Type: 2

Referenced by Line: -

---------------------------------------------------------------------------

Total entries: 2.

Check the detail information of the DBA profile in the inactive area

GPON(config)# show deploy inactive-domain dba 0

aim 0 name abcde

type 1 fix 10240

Check the brief information of the line profile in the inactive area

GPON(config)# show deploy inactive-domain line brief all

Index: 0

Name:abcde

Device type:n20-100

Referenced by Rule: -
---------------------------------------------------------------------------

Index: 1

Name:fghij

Device type: n20-400

Referenced by Rule: -

---------------------------------------------------------------------------

Total entries: 2.

Check the detail information of the line profile in the inactive area

GPON(config)# show deploy inactive-domain line 0

aim 0 name abcde

device type n20-100

tcont 1 profile dba index 1

gemport traffic-mode queue

gemport 1 tcont 1

gemport 2 tcont 1

gemport 3 tcont 1

mapping mode port-vlan-priority

mapping 1 vlan 1 priority 0 port eth 1 gemport 1

mapping 2 vlan 100 priority 0 port eth 1 gemport 2

mapping 3 vlan 200 priority 0 port eth 1 gemport 3

flow 1 port eth 1 default vlan 1 0

flow 2 port eth 1 cvlan 100 0 keep

multicast us-tag add 200 0 port 1

multicast ds-tag remove port 1

Check the brief information of the rule profile in the inactive area

GPON(config)# show deploy inactive-domain rule brief all

ONT : 0/1/1

Name:abcde

Reference Line: 0

---------------------------------------------------------------------------
 ONT : 0/1/2

Name:fghij

Reference Line: -

---------------------------------------------------------------------------

Total entries: 2.

Check the detail information of the rule profile in the inactive area

GPON(config)# show deploy inactive-domain rule 0/1/1

aim 0/1/1 name:abcde

permit sn string-hex GPON-12345678 line 1 default line 1

Check the brief information of the unique profile in the inactive area

GPON(config)# show deploy inactive-domain unique brief all

ONT: 0/1/1

Name:abcde

---------------------------------------------------------------------------

ONT: 0/1/2

Name:fghij

---------------------------------------------------------------------------

ONT: 0/1/3

Name:aswq

---------------------------------------------------------------------------

Total entries: 3.

Check the detail information of the unique profile in the inactive area

GPON(config)# show deploy inactive-domain unique 0/1/1

aim 0/1/1 name abcde

description FTTH

gemport 1 vlan-profile 1 us-traffic-profile 1 ds-traffic-profile 1

sip proxy server primary ip 192.168.2.100 signal port 6666

sip user 1 name admin password 123456 telno 10000

2.1.19 show deploy difference

 This command displays the differences of the deployment configuration in inactive area and

activate area.

show deploy difference statistic

show deploy difference vlan brief { <index_list> | all }

show deploy difference vlan { index <index_num> | name <name>}

show deploy difference us-traffic brief { <index_list> | all }

show deploy difference us-traffic { <index_num> | name <name>}

show deploy difference ds-traffic brief { <index_list> | all }

show deploy difference ds-traffic { <index_num> | name <name>}

show deploy difference dba brief { <index_list> | all }

show deploy difference dba { <index_num> | name <name>}

show deploy difference line brief { <index_list> | all }

show deploy difference line { <index_num> | name <name>}

show deploy difference rule brief { <ont_id_list> | all }

show deploy difference rule { <ont_id> | name <name>}

show deploy difference unique brief { <ont_id_list> | all }

show deploy difference unique { <ont_id> | name <name>}

【Parameter Specification】

index_list: entry index number combination, representing multiple entries. The range of

individual index numbers ranges from <0-(M-1)>, M is the maximum ONTs supported by the

OLT

index_num: the index of the profile entry, the range is <0-(M-1)>, M is the maximum ONTs

supported by the OLT

name: the name of the profile entry, combined with a string, and the range of the length is

<1-128>

all: Specifies all profile entries

ont_id: ONT ID number, in the form slot_num / port_num / ont_num, slot_num is the slot

number, port_num is the port number, ont_num is the ONT's index assigned by the OLT

ont_id_list: the list of ONT IDs. Such as 0/1 / 1-0 / 2 / 5,0 / 2/10

【Usage】
 All modes

【Example】

Check the statistics of difference in the active and inactive area

GPON (config) # show deploy difference statistic

Profile Difference

VLAN 2

US-Traffic 2

DS-Traffic 2

DBA 1

Line 5

Rule 1

Unique 0

Check the difference of the vlan profile in the active and inactive area

GPON (config) # show deploy difference vlan brief all

Index Status

0 modify

2 delete

3 add

Total entries: 3.

Check the detail difference of the vlan profile in the active and inactive area

GPON (config) # show deploy difference vlan index 0

Active-domain:

aim 0 name abcde

translate old-vlan 100 1 new-vlan 200 3

-------------------------------------------------- -------------------------

Inactive-domain:

aim 0 name abcde

translate old-vlan 200 1 new-vlan 300 3

2.1.20 show deploy match

 This command is used to check the matched rule or unique profile in the active or inactive

area of the specified ONT.

show deploy match {active-domain | inactive-domain} { sn { string-hex <sn_num>

| hex <sn_num>} | pw { string <password> | hex <password>} | loid <loid> | lopw<logical_

password> }

【Parameter Specification】

sn_num: ONT SN number for the physical identification of the ONT. Exact match, has two

types of formats:

string-hex format: STRING <13-13>, before the four character, bit 5 '-' after the 8-bit

hexadecimal number;

hex format: STRING <16-16>, all the bits are hexadecimal numbers

password: ONT key. Exact match, there are two input methods:

string format: STRING <10-10>, it consists of 10 characters;

hex format: STRING <20-20>, a 20-bit hexadecimal numbers.

loid: ONT logical identity. STRING <24-24>, an exact match by 24 characters

logical_password: ONT logical identity key. STRING <12-12>, an exact match by 12

characters

【Usage】

All modes

【Example】

Check the matched rule or unique profile in the active or inactive area of the specified ONT

GPON (config) # show deploy match active-domain sn string hex GCOM-12345678

Unique: 1

Rule Description

1 abc

Total entries:1.

2.1.21 show deploy affect

This command is used to check whether the deployment configuration in the inactive area
would affect the ONT's existed configuration or not if we active that.

show deploy affect {interface gpon {<interface_list> | all} | ont <ont_id>}

【Parameter Specification】

Interface_list: GPON port list, containing multiple GPON ports. Representation of the port

number is slot_num / port_num, slot_num slot number, port_num slot is the port

number.Contiguous ports can be connected to a minus sign, separated by commas discrete port,

such as: 1 / 1-0 / 5,0 / 8

all: All GPON port

ont_id: ONT ID number, in the form slot_num / port_num / ont_num, slot_num slot number,

port_num slot is the port number, ont_num line is on the ONT, OLT assigned index number

【Usage】

All modes

【Example】

Check all the ONTs which will be affected by the configuration in the inactive area.

GPON (config) # show deploy affect all

Port ONT

g0 / 1 0/1 / 1-0 / 1 / 2,0 / 1/5

g0 / 2 0/2 / 1-0 / 2 / 2,0 / 2/5

...

g0 / 16 0/16 / 1-0 / 16 / 2,0 / 16/5

2.1.22 show deploy status

This command displays the current status of the deployment permission, including the

current permission owner, the current owner's terminal type, IP address, the time when the owner

got the permission and the last time when the owner enabled the deployment configuration.

When the device need to reboot and load the configuration, the system will apply for

temporary permission to deploy at first. And after that, the permission will be released

automatically.

show deploy status

【Parameter Specification】

no

【Usage】

All modes

【Example】

Check the current status of the deployment permission

GPON (config) # Show Deploy Status

Username: admin

Terminal: console

User's IP Address: -

Request Time: 2001-04-14 23:54:52

Last Activate Time: 2001-04-15 23:54:52

2.1.23 show deploy history

This command displays the historical record of the deployment permission. The administrator

can get the information who logged in the system and changed the deployment configuration

according the record.

show deploy history [index <index_num>]

【Parameter Specification】

index_num: historical record index, in the range of <0-19> 0 indicates a recent operation

record

【Usage】

All modes

【Example】

Check the historical record of the deployment permission.

GPON (config) # Show Deploy History

Index: 0

Username: admin

Terminal: telnet
 User's IP Address: 192.168.10.100

Request Time: 2015-06-09 15:22:30

Activate Time: 2015-06-09 15:23:31

2015-06-09 15:23:30

Release Time: 2015-06-09 15:24:31

2.2 VLAN Profile Configuration

 translate

 add

 default

Note: Each vlan profile entry can configure more than one translation or add rules, but the old vlan

or the inner vlan should be different. The default vlan rule is used in the service scene needs vlan

transparent based on the GEM Port. Each vlan profile entry can only configure one default vlan

rule and other rules cannot be configured in this entry.

2.2.1 translate

This command is used to configure the translation rule of the ONT service vlan. The vlan

profile should be quoted in the line profile or unique profile. After quoted, the OLT will translate

the old service vlan of the ONT’s upstream to a new vlan.

translate old-vlan <vid> [ <priority> ] new-vlan <vid> [ <priority> ]

【Parameter Specification】

vid: VLAN ID, in the range of <1-4094>

priority: 802.1P priority, in the range of <0-7>

【Usage】

vlan profile entry configuration mode

【Example】

Config an vlan profile entry

GPON (deploy-profile-vlan-1) # translate old-vlan 100 1 new-vlan 200 3

2.2.2 add

This command is used to configure the addition rule of the ONT service vlan. The vlan

profile should be quoted in the line profile or unique profile. After quoted, the OLT will add an

outer service vlan to the ONT’s upstream.

add inner-vlan <vid> [ <priority> ] outer-vlan <vid> [ <priority> ]

【Parameter Specification】

vid: VLAN ID, in the range of <1-4094>

priority: 802.1P priority, in the range of <0-7>

【Usage】

vlan profile entry configuration mode

【Example】

Config an vlan profile entry

GPON (deploy-profile-vlan-1) # add inner-vlan 100 1 outer-vlan 200 3

2.2.3 default

This command is used to configure the default addition rule of the ONT service vlan. The

vlan profile should be quoted in the line profile or unique profile. After quoted, the OLT will add

an outer vlan to the ONT’s upstream no matter the upstream has vlan or not. This rule is used in

the scene which needs vlan transparent.

default vlan <vid> [ <priority> ]

【Parameter Specification】

vid: VLAN ID, in the range of <1-4094>

priority: 802.1P priority, in the range of <0-7>

【Usage】

vlan profile entry configuration mode

【Example】

Config an vlan profile entry

GPON (deploy-profile-vlan-1) # default vlan 200 3

2.3 Us-traffic Profile Configuration

 us

2.3.1 us

This command is used to configure the QoS parameters of the ONT upstream based on the

GEM Port. The QoS of the ONT upstream based on the GEM Port has two mode: Queue

scheduling and CAR scheduling.

In the Queue scheduling mode, the OLT will give each GEM Port a queue priority, and the

GEM Ports in the same T-CONT will transmit the upstream traffic according to their queue

priority. The higher priority the GEM Port has, the more bandwidth can be got.

In the CAR scheduling mode, the OLT will distribute an upstream bandwidth for each GEM

Port, and the GEM Ports in the same T-CONT will transmit the upstream traffic according to the

bandwidth map configured by the OLT.

us { queue <queue_id> | car cir <cir> cbs <cbs> pir <pir> pbs <pbs> }

【Parameter Specification】

queue_id: the GEM Port queue id. This parameter ranges from <0-7>, 0 is the lowest priority

and 7 is the highest priority

cir: guaranteed bandwidth. The unit is kbps, and must be divisible by 64

cbs: guaranteed bandwidth burst. The unit is KB

pir: peak bandwidth. The unit is kbps, and must be divisible by 64.The peak bandwidth

should be more than the guaranteed bandwidth

pbs: peak bandwidth burst. The unit is KB

【Usage】

Us-traffic profile entry configuration mode

【Example】

Config an us-traffic profile entry

GPON (deploy-profile-vlan-1) # us queue 1

2.4 Ds-traffic Profile Configuration

 ds

2.4.1 ds

This command is used to configure the QoS parameters of the ONT downstream based on the

GEM Port. The QoS of the ONT downstream based on the GEM Port just supports CAR

scheduling.

In the CAR scheduling mode, the OLT will distribute an downstream bandwidth for each

GEM Port, and the GEM Ports will transmit the downstream traffic according to the bandwidth

map configured by the OLT.

ds car bandwidth <bandwidth>

【Parameter Specification】

bandwidth: the downstream bandwidth. The unit is kbps

【Usage】

ds-traffic profile entry configuration mode

【Example】

Config an ds-traffic profile entry

GPON (deploy-profile-vlan-1) # ds car bandwidth 10000

2.5 DBA Profile Configuration

 type

2.5.1 type

This command is used to configure the DBA profile. There are five types: type 1,typ

e2,type3,type4 and type5.

type 1 fix <fixed_bandwidth>

type 2 assured <assured_bandwidth>

 type 3 assured <assured_bandwidth> max <not_assured_bandwidth>

type 4 max <best_effort_bandwidth>

type 5 fix <fixed_bandwidth> assured <assured_bandwidth> max <not_assured_ba

ndwidth>

【Parameter Specification】

fixed_bandwidth: fixed bandwidth, the unit is kbps, and must be divisible by 64, in the range

of <256-800000>. The sum of the ONTs' fixed bandwidth and assured bandwidth under the same

PON port can not exceed 1.25Gbps

assured_bandwidth: assured bandwidth, the unit is kbps, and must be divisible by 64, in the

range of <0-800000>. The sum of the ONTs' fixed bandwidth and assured bandwidth under the

same PON port can not exceed 1.25Gbps

not_assured_bandwidth: non-assured bandwidth, the unit is kbps, and must be divisible by 64,

in the range of <256-1200000>. Non-assured bandwidth must be more than or equal to the sum of

the fixed bandwidth and assured bandwidth.

best_effort_bandwidth: best-effort bandwidth, the unit is kbps, and must be divisible by 64,

in the range of <256-1200000>. Best-effort bandwidth must be more than or equal to the sum of

the fixed bandwidth and assured bandwidth.

【Usage】

DBA profile entry configuration mode

【Example】

Config a DBA profile entry

GPON (deploy-profile-dba-30) #type 1 fix 4096

2.6 Line Profile Configuration

 device type

 tcont

 gemport

 mapping

 flow
 mac-address-table max-mac-count

 multicast mode

 multicast group-limit

 multicast us-tag

 multicast ds-tag

 multicast program

 multicast fast-leave disable

 local shutdown

 local flow-control

 local bandwidth egress

 local loop-detect

 local switch

 local catv-agc

2.6.1 device type

This command is used to configure the ONT's device type. When ONT registers on the OLT,

it will report its device type to the OLT and then OLT will send the cofiguration to the ONT

according to this device type.

device type <name>

【Parameter Specification】

name: ONT device type name.

【Usage】

Line profile entry configuration mode

【Example】

Config a device type in the line profile entry

GPON (deploy-profile-line-1) #device type n20-100

2.6.2 tcont

This command is used to create a T-CONT and assign a DBA profile to this
T-CONT. T-CONT is a physical resource in the GPON system. All the upstreams of the ONT

should be collected into the T-CONT before transmited to the OLT and the DBA profile

determines the size of the T-CONT, that is to say, the bandwidth of the upstream.

tcont <tcont_id> profile dba { <index_num> | name <name> }

no tcont <tcont_id>

【Parameter Specification】

tcont_id: the index of T-CONT. In the range of <1-8>

index_num: the index of the profile entry, the range is <0-(M-1)>, M is the maximum ONTs

supported by the OLT

name: the name of the profile entry, combined with a string, and the range of the length is

<1-128>

【Usage】

Line profile or unique profile entry configuration mode

【Example】

Config a T-CONT in the line profile entry

GPON (deploy-profile-line-1) #tcont 1 profile dba index 1

2.6.3 gemport

This command is used to create a GEM Port and configure the related attributes.

gemport traffic-mode { car | queue }

gemport <gem_index> tcont <tcont_id> [ vlan-profile { <index_num> | name <name> } ]

[ us-traffic-profile { <index_num> | name <name> } ] [ ds-traffice-profile { <index_num> |

name <name> } ]

no gemport <gem_index>

【Parameter Specification】

gem_index: the index of GEM Port. In the range of <1-1024>

tcont_id: the index of T-CONT. In the range of <1-8>

index_num: the index of the profile entry, the range is <0-(M-1)>, M is the maximum ONTs

supported by the OLT

 name: the name of the profile entry, combined with a string, and the range of the length is

<1-128>

【Usage】

Line profile entry configuration mode

【Example】

Config a GEM Port in the line profile entry

GPON (deploy-profile-line-1) # gemport traffic-mode queue

GPON (deploy-profile-line-1) # gemport 1 tcont 1 vlan-profile 1 us-traffic-profile 1

ds-traffic-profile 1

2.6.4 mapping

This command is used to configure the GEM Port mapping rule. The rule includes: Port,

VLAN ID, 802.1P priority, Port + VLAN ID, Port + 802.1P priority, VLAN ID + 802.1P priority

and Port + VLAN ID + 802.1P priority

mapping mode {port | port-priority | port-vlan | port-vlan-priority | priority | vlan | vla

n-priority }

mapping <index_num> { vlan <vid> | priority <priority> | port { eth <port_id> | veip

| iphost }} gemport <gem_index>

no mapping <index_num>

【Parameter Specification】

index_num: the index of the mapping rule, in the range of <0-47>

vid: VLAN ID, in the range of <1-4094>

priority: 802.1P priority, in the range of <0-7>

eth: ONT ethernet port

veip: ONT routing ports, namely WAN interface

iphost: ONT voice interface

port_id: ONT ethernet port number, in the range of <1-8>

gem_index: the index of GEM Port. In the range of <1-24>

【Usage】
 Line profile entry configuration mode

【Example】

Config a mapping rule in the line profile entry

GPON (deploy-profile-line-1) # mapping mode vlan

GPON (deploy-profile-line-1) # mapping 1 vlan 100 gemport 1

2.6.5 flow

This command is used to configure the vlan processing strategy of the ONT LAN interface:

transparent, trunk, tag, translation or aggregation.

flow <flow_id> port { eth <port_id> | veip | iphost } [ etype { ipoe | pppoe | arp } ]

transparent

flow <flow_id> port { eth <port_id> | veip | iphost } [ etype { ipoe | pppoe | arp } ]

default vlan <vid> [ <priority> ]

flow <flow_id> port { eth <port_id> | veip | iphost } [ etype { ipoe | pppoe | arp } ]

vlan <vid> [ <priority> ] keep

flow <flow_id> port { eth <port_id> | veip | iphost } [ etype { ipoe | pppoe | arp } ]

vlan <vid> [ <priority> ] translate vlan <vid> [ <priority> ]

flow <flow_id> port { eth <port_id> | veip | iphost } [ etype { ipoe | pppoe | arp } ]

vlan <vid> [ <priority> ] add vlan <vid> [ <priority> ]

no flow <flow_id>

【Parameter Specification】

flow_id: the index of vlan processing strategy, in the range of <0-63>

eth: ONT ethernet port

veip: ONT routing ports, namely WAN interface

iphost: ONT voice interface

port_id: ONT ethernet port number, in the range of <1-8>

ipoe: ethernet type is 0x0800

pppoe: ethernet type is 0x8863 or 0x8864

arp: ethernet type is 0x0806

 vid: VLAN ID, in the range of <1-4094>

priority: 802.1P priority, in the range of <0-7>

【Usage】

Line profile entry configuration mode

【Example】

Config a vlan processing strategy in the line profile entry

GPON (deploy-profile-line-1) # flow 1 port eth 1 default vlan 100 7

2.6.6 mac-address-table max-mac-count

This command is used to configure the maximum MAC addresses learned by the ONT.

mac-address-table max-mac-count <num> [ port <port_id> ]

no mac-address-table max-mac-count [ port <port_id> ]

【Parameter Specification】

num: Maximum number of dynamic MAC address, ranging from <1-255>

port_id: ONT ethernet port number, in the range of <1-8>

【Usage】

Line profile entry configuration mode

【Example】

Config the maximum number of MAC address in the line profile entry

GPON (deploy-profile-line-1) # mac-address-table max-mac-count 10 port 1

2.6.7 multicast mode

This command is used to configure the ONT multicast working mode: igmp-snooping mode

or controllable multicast mode

multicast mode { igmp-snooping | olt-control } [ port <port_id> ]

no multicast mode [ port <port_id> ]

【Parameter Specification】

port_id: ONT ethernet port number, in the range of <1-8>

【Usage】

Line profile entry configuration mode

【Example】

Config the multicast working mode in the line profile entry

GPON (deploy-profile-line-1) #multicast mode olt-control

2.6.8 multicast group-limit

This command is used to configure the maximum multicast groups learned by the ONT.

multicast group-limit <num> [ port <port_id> ]

no multicast group-limit [ port <port_id> ]

【Parameter Specification】

num: Maximum number of multicast groups, ranging from <1-128>

port_id: ONT ethernet port number, in the range of <1-8>

【Usage】

Line profile entry configuration mode

【Example】

Config the maximum multicast groups in the line profile entry

GPON (deploy-profile-line-1) #igmp group-limit 10 port 1

2.6.9 multicast us-tag

This command is used to configure the upstream multicast vlan processing strategy: add,

translate.

multicast us-tag add <vid> [ <priority> ]

multicast us-tag translate <vid> [ <priority> ]

multicast us-tag add <vid> [ <priority> ] port <port_id>

multicast us-tag translate <vid> [ <priority> ] port <port_id>

no multicast us-tag

no multicast us-tag port <port_id>

【Parameter Specification】

vid: VLAN ID, in the range of <1-4094>

priority: 802.1P priority, in the range of <0-7>

port_id: ONT ethernet port number, in the range of <1-8>

【Usage】

Line profile entry configuration mode

【Example】

Config the upstream multicast vlan processing strategy in the line profile entry

GPON (deploy-profile-line-1) #multicast us-tag add 10 port 1

2.6.10 multicast ds-tag

This command is used to configure the downstream multicast vlan processing strategy:

remove, add or translate.

multicast ds-tag remove

multicast ds-tag add <vid> [ <priority> ]

multicast ds-tag translate <vid> [ <priority> ]

multicast ds-tag remove port <port_id>

multicast ds-tag add <vid> [ <priority> ] port <port_id>

multicast ds-tag translate <vid> [ <priority> ] port <port_id>

no multicast ds-tag

no multicast ds-tag port <port_id>

【Parameter Specification】

vid: VLAN ID, in the range of <1-4094>

priority: 802.1P priority, in the range of <0-7>

port_id: ONT ethernet port number, in the range of <1-8>

【Usage】

Line profile entry configuration mode

【Example】

Config the downstream multicast vlan processing strategy in the line profile entry
 GPON (deploy-profile-line-1) #multicast ds-tag add 10 port 1

2.6.11 multicast program

This command is used to configure the controllable multicast groups.

multicast program <index> permit mcast-ip <ip> [ source-ip <ip> | vlan <vid> | ba

ndwidth <bandwidth> ]

multicast program <index> permit mcast-ip <ip> [ source-ip <ip> | vlan <vid> | ba

ndwidth <bandwidth> ] port <port_id>

multicast program <index> preview mcast-ip <ip> [ source-ip <ip> | vlan <vid> | b

andwidth <bandwidth> | duration <duration-time> | interval <interval-time> | times <pr

eview-times> ]

multicast program <index> preview mcast-ip <ip> [ source-ip <ip> | vlan <vid> | b

andwidth <bandwidth> ] duration <duration-time> interval <interval-time> times <previ

ew-time> port <port_id>

【Parameter Specification】

index: the index of controllable multicast entry

port_id: ONT ethernet port number, in the range of <1-8>

ip: multicast IP address or multicast source IP address

vid: VLAN ID, in the range of <1-4094>

bandwidth: the bandwidth of multicast traffic

duration-time: the time preview once

interval-time: the time preview between two times

preview-times: the total times preview

【Usage】

Line profile entry configuration mode

【Example】

Config a controllable multicast group in the line profile entry

GPON (deploy-profile-line-1) #multicast program 0 ip 224.1.2.3 vlan 10 permit port 1

2.6.12 multicast fast-leave disable

This command is used to disable the multicast group fast leave function of the ONT.

multicast fast-leave disable [ port <port_id> ]

no multicast fast-leave disable [ port <port_id> ]

【Parameter Specification】

port_id: ONT ethernet port number, in the range of <1-8>

【Usage】

Line profile entry configuration mode

【Example】

Config a controllable multicast group in the line profile entry

GPON (deploy-profile-line-1) #multicast fast-leave disable port 1

2.6.13 local shutdown

This command is used to disable the ONT's ethernet port or CATV port

local shutdown { port <port_id> | catv-port <catv_port_id> }

no local shutdown { port <port_id> | catv-port <catv_port_id> }

【Parameter Specification】

port_id: ONT ethernet port number, in the range of <1-8>

catv_port_id:ONT CATV port number,in the range of <1-4>

【Usage】

Line profile entry configuration mode

【Example】

Disable an ethernet port of ONT in the line profile entry

GPON (deploy-profile-line-1) # local shutdown port 1

2.6.14 local flow-control

This command is used to enable the flow control function of ONT Ethernet port.

local flow-control port <port_id>

 no local flow-control port <port_id>

【Parameter Specification】

port_id: ONT ethernet port number, in the range of <1-8>

【Usage】

Line profile entry configuration mode

【Example】

Enable the flow control function of ONT Ethernet port in the line profile entry

GPON (deploy-profile-line-1) # local flow-control port 1

2.6.15 local bandwidth egress

This command is used to enable the outbound rate limit function of ONT Ethernet port .

local bandwidth egress port <port_id> <bandwidth>

no local bandwidth egress port <port_id> <bandwidth>

【Parameter Specification】

port_id: ONT ethernet port number, in the range of <1-8>

bandwidth: outbound bandwidth, the unit is kbps, in the range of < 64-1024000>

【Usage】

Line profile entry configuration mode

【Example】

Enable the outbound rate limit function of ONT Ethernet port in the line profile entry

GPON (deploy-profile-line-1) # local bandwidth egress port 1 51200

2.6.16 local loop-detect

This command is used to enable the loop detection function of the ONT.

local loop-detect port <port_id>

no local loop-detect port <port_id>

【Parameter Specification】

port_id: ONT ethernet port number, in the range of <1-8>

【Usage】

Line profile entry configuration mode

【Example】

Enable the loop detection function of the ONT in the line profile entry

GPON (deploy-profile-line-1) # local loop-detect port 1

2.6.17 local switch

This command is used to enable the local switching function of the ONT ethernet port.

local switch

no local switch

【Parameter Specification】

no

【Usage】

Line profile entry configuration mode

【Example】

Enable the local switching function of the ONT ethernet port in the line profile entry

GPON (deploy-profile-line-1) # local switch

2.6.18 local catv-agc

This command is used to set the AGC function of the ONT CATV port.

local catv-agc mode { optical-based | rf-based } { decrease | increase } <range> catv-port

<catv_port_id>

no local catv-agc catv-port <catv_port_id>

【Parameter Specification】

port_id: ONT ethernet port number, in the range of <1-8>

catv_port_id:ONT CATV port number,in the range of <1-4>

range:the range of gain. In the range of <1-120>,the unit is 0.1dB

【Usage】

Line profile entry configuration mode

【Example】

Set the AGC function of the ONT CATV port

GPON (deploy-profile-line-1) # local catv-agc mode optical-based decrease 10 catv-por

t 1

2.7 Unique Profile Configuration

 description

 tcont

 gemport

 sip agent

 sip user

 sip digitmap

2.7.1 description

This command is used to configure the ONT’s description.

description <description>

【Parameter Specification】

description: ONT’s description, combined with a string, and the range of the length is

<1-128>

【Usage】

Unique profile entry configuration mode

【Example】

Configure an ONT description in the unique profile entry

GPON (deploy-profile-unique-1) # description FTTH

2.7.2 tcont

This command is used to create a T-CONT and assign a DBA profile to this

T-CONT. T-CONT is a physical resource in the GPON system. All the upstreams of the ONT
should be collected into the T-CONT before transmited to the OLT and the DBA profile

determines the size of the T-CONT, that is to say, the bandwidth of the upstream.

tcont <tcont_id> profile dba { <index_num> | name <name> }

no tcont <tcont_id>

【Parameter Specification】

tcont_id: the index of T-CONT. In the range of <1-8>

index_num: the index of the profile entry, the range is <0-(M-1)>, M is the maximum ONTs

supported by the OLT

name: the name of the profile entry, combined with a string, and the range of the length is

<1-128>

【Usage】

Line profile or unique profile entry configuration mode

【Example】

Config a T-CONT in the unique profile entry

GPON (deploy-profile-unique-0/1/1) #tcont 1 profile dba index 1

2.7.3 gemport

This command is used to configure the ONT’s vlan profile or traffic profile based on the

gemport

gemport <gem_index> vlan-profile { <index_num> | name <name> }

gemport <gem_index> us-traffic-profile { <index_num> | name <name> }

gemport <gem_index> ds-traffice-profile { <index_num> | name <name> }

【Parameter Specification】

gem_index: the index of GEM Port. In the range of <1-1024>

tcont_id: the index of T-CONT. In the range of <1-8>

index_num: the index of the profile entry, the range is <0-(M-1)>, M is the maximum ONTs

supported by the OLT

name: the name of the profile entry, combined with a string, and the range of the length is
<1-128>

【Usage】

Unique profile entry configuration mode

【Example】

Configure a vlan profile and traffic profile for an ONT in the unique profile entry

GPON (deploy-profile-unique-0/1/1) # gemport 1 vlan-profile 1 us-traffic-profile 1

ds-traffic-profile 1

2.7.4 sip agent

This command is used to configure the SIP agent of the ONT.

sip agent proxy-server <ip> [outbound-proxy <ip>] [registrar-server <ip>] signal-port

<port_id>

【Parameter Specification】

ip: IP address of the server

port_id: signaling port number, the default is 5060

【Usage】

Unique profile entry configuration mode

【Example】

Configure a SIP agent in the unique profile entry

GPON (deploy-profile-unique-0/1/1) #sip agent proxy-server 192.168.2.100 signal-port 6666

2.7.5 sip user

This command is used to configure the voice port of the ONT.

sip user ip <ip> mask <ip_mask> vlan <vid>

sip user <user_id> name <username> password <password> telno <phone_num>

【Parameter Specification】

ip: IP address of the local voice interface

ip_mask: IP address mask

vid: VLAN ID, in the range of <1-4094>

 user_id: ONT POTS port id, in the range <1-2>

username: SIP server for authentication username

password: password for SIP server authentication

phone_num: ONT local voice telephone number

【Usage】

Unique profile entry configuration mode

【Example】

Configure a SIP user in the unique profile entry

GPON (deploy-profile-unique-0/1/1) #sip user ip-address 192.168.2.20 mask 255.255.255.0

vlan 20

GPON (deploy-profile-unique-0/1/1) #sip user 1 name admin password 123456 telno 10000

2.7.6 sip digitmap

This command is used to configure the SIP digitmap of the ONT. Digitmap provides the

dailing rules when we make a phone call.

sip digitmap dial-plan-id <id> dial-plan-token <token>

【Parameter Specification】

id: the index of the digitmap

token: the content of the digitmap

【Usage】

Unique profile entry configuration mode

【Example】

Configure a SIP digitmap in the unique profile entry

GPON (deploy-profile-unique-1) #sip digit-map dial-plan-id 1 dial-plan-token * x. * X. #

2.8 Rule Profile Configuration

 permit

2.8.1 permit
 This command is used to configure the permit rule. The ONT matching the rule can register

on the OLT and the configuration in the line profile will be sent to the ONT at the same time.

The OLT supports six ONT authentication modes: SN, Password, SN+Password, LOID,

Logical Password, LOID+ Logical Password.

The line profile will be bound with the ONT when the ONT authentication rule is created.

Each rule can configure more than one line profiles, and the OLT will match the correct line

profile to the ONT according to the device type reported to the OLT. If the device type reported

by the ONT is not match with the line profile, the OLT would not send the configuration to the

ONT except that we have configured a default line profile.

permit sn { string-hex <sn_num> | hex <sn_num> } line { <index_list> | name <name> }

[ default line { <index_num> | name <name> } ]

permit pw { string <password> | hex <password> } line { <index_list> | name <name> }

[ default line { <index_num> | name <name> } ]

permit loid <loid> line { <index_list> | name <name> } [ default line { <index_num> |

name <name> } ]

permit lopw <logical_password> line { <index_list> | name <name> } [ default line

{ <index_num> | name <name> } ]

permit sn-pw { string-hex <sn_num> | hex <sn_num> } { string <password> | hex

<password> } line { <index_list> | name <name> } [ default line { <index_num> | name

<name> } ]

permit loid-lopw <loid> <logical_password> line { <index_list> | name <name> }

[ default line { <index_num> | name <name> } ]

【Parameter Specification】

sn_num: the physical identification of the ONT. There are two formats:

string-hex format: STRING <13-13>, the first four string is character, then '-' behind, after

that is 8 hexadecimal number

hex format: STRING <16-16>, all the bits are in hexadecimal number

password: ONT key combined with SN. There are two input methods:

string format: STRING <1-10>, full match;

hex format: STRING <1-20>, full match.

 loid: ONT logical identity. STRING <1-24>, full match

logical_password: ONT key combined with logical identity. STRING <1-12>, full match

index_list: entry index number combination, representing multiple entries. The range of

individual index numbers ranges from <0-(M-1)>, M is the maximum ONTs supported by the

OLT

index_num: the index of the profile entry, the range is <0-(M-1)>, M is the maximum ONTs

supported by the OLT

name: the name of the profile entry, combined with a string, and the range of the length is

<1-128>

【Usage】

Rule profile entry configuration mode

【Example】

Configure a permit rule in the rule profile entry

GPON (deploy-profile-rule-0/1/1) #permit sn string-hex GPON-12345678 line 1

3 ONT Management Function

3.1 ONT Information Query

 show ont optical-info

 show ont statistics

 show ont port- status

 show ont multicast

 show ont info

 show ont brief

 show ont description

 show ont profile

 show ont upgrade-status

3.1.1 show ont optical-info

 This command is used to check the information of ONT's optical parameter, including: the

working voltage, the bias current, the received optical power, the transmitting optical power and

the working temperature.

show ont optical-info { <ont_id> | sn { string-hex <sn_num> | hex <sn_num> } }

【Parameter Specification】

ont_id: ONT ID number, in the form slot_num / port_num / ont_num, slot_num is the slot

number, port_num is the port number, ont_num is the ONT's index assigned by the OLT

sn_num: the physical identification of the ONT. There are two formats:

string-hex format: STRING <13-13>, the first four string is character, then '-' behind, after

that is 8 hexadecimal number

hex format: STRING <16-16>, all the bits are in hexadecimal number

【Usage】

All modes

【Example】

Check the optical parameter information of ONT 0/6/2

GPON(config)#show ont optical-info 0/6/2

Power Feed Voltage(V) : 3.36

RX Optical Power(dBm) : -9.958 (OLT TX: 4.020)

TX Optical Power(dBm) : 2.178 (OLT RX: -11.805)

Laser Bias Current(mA) : 16.320

Temperature(C) : 53.00

CATV RX Power(dBm) : -

CATV Output Power(dBmV) : -

3.1.2 show ont statistics

This command is used to check the statistics of frames received or transmitted by the ONT.

The statistics is based on the ethernet port or the GEM Port or the ONT.

show ont statistics { <ont_id> | sn { string-hex <sn_num> | hex <sn_num> } } [ po

rt <port_id> | gem { broadcast | multicast | unicast <gem_index>} | traffic ]

 show ont statistics overall { <ont_id> | sn { string-hex <sn_num> } [ port <port_id>

【Parameter Specification】

ont_id: ONT ID number, in the form slot_num / port_num / ont_num, slot_num is the slot

number, port_num is the port number, ont_num is the ONT's index assigned by the OLT

sn_num: the physical identification of the ONT. There are two formats:

string-hex format: STRING <13-13>, the first four string is character, then '-' behind, after

that is 8 hexadecimal number

hex format: STRING <16-16>, all the bits are in hexadecimal number

port_id: ONT ethernet port number, in the range of <1-8>

gem_index: the index of GEM Port. In the range of <1-1024>

【Usage】

All modes

【Example】

Check the optical parameter information of ONT 0/6/2

GPON (config) #show ont statistics 0/6/2

Discarded frames: 0

Upstream frames: 0

Upstream bytes: 4043664

Downstream frames: 0

Downstream bytes: 0

Up traffic (kbps): 37

Down traffic (kbps): 0

3.1.3 show ont port-status

This command is used to check the status of the ONT ethernet port, including port enable

status, port speed, duplex mode.

show ont port-status { <ont_id> | sn { string-hex <sn_num> | hex <sn_num> } } po

rt <port_id>
【Parameter Specification】

ont_id: ONT ID number, in the form slot_num / port_num / ont_num, slot_num is the slot

number, port_num is the port number, ont_num is the ONT's index assigned by the OLT

sn_num: the physical identification of the ONT. There are two formats:

string-hex format: STRING <13-13>, the first four string is character, then '-' behind, after

that is 8 hexadecimal number

hex format: STRING <16-16>, all the bits are in hexadecimal number

port_id: ONT ethernet port number, in the range of <1-8>

【Usage】

All modes

【Example】

Check the status of ONT 0/6/1 ethernet port 1

GPON (config) #show ont port-status 0/6/1 port 1

Port State is Enable, Gigabit Ethernet full duplex

3.1.4 show ont multicast

This command is used to check the multicast groups learned by ONT.

show ont multicast { <ont_id> | sn { string-hex <sn_num> | hex <sn_num> } } [ po

rt <port_id> ]

【Parameter Specification】

ont_id: ONT ID number, in the form slot_num / port_num / ont_num, slot_num is the slot

number, port_num is the port number, ont_num is the ONT's index assigned by the OLT

sn_num: the physical identification of the ONT. There are two formats:

string-hex format: STRING <13-13>, the first four string is character, then '-' behind, after

that is 8 hexadecimal number

hex format: STRING <16-16>, all the bits are in hexadecimal number

port_id: ONT ethernet port number, in the range of <1-8>

【Usage】

All modes
【Example】

Check the multicast groups learned by ONT 0/6/1

GPON (config) #show ont multicast 0/6/1 port 2

MAC Address: 01: 00: 5e: 01: 02: 03

IP Address: 224.1.2.3

VLAN ID: 100

Client IP: 3.3.3.3

Age time: 0

IGMP Version: 0

Total entries: 1.

3.1.5 show ont info

This command is used to check the detail information of ONT.

show ont info { <ont_id> | sn { string-hex <sn_num> | hex <sn_num> } }

【Parameter Specification】

ont_id: ONT ID number, in the form slot_num / port_num / ont_num, slot_num is the slot

number, port_num is the port number, ont_num is the ONT's index assigned by the OLT

sn_num: the physical identification of the ONT. There are two formats:

string-hex format: STRING <13-13>, the first four string is character, then '-' behind, after

that is 8 hexadecimal number

hex format: STRING <16-16>, all the bits are in hexadecimal number

【Usage】

All modes

【Example】

Check the detail information of ONT 0/6/2

GPON(config)#show ont info 0/6/2

ONT : 0/6/2

Description : -

Status : Online
 Distance(m) : <10

Vendor ID : CMSZ

Software Version : R4.1.36.436 / R4.1.36.474

Firmware Version : N20-400

Equipment ID : CMSZ

SN : CMSZ-d2716231

Password : 12345678

LOID : 12345678

LOID Password : -

Uplink PON ports : 1

ETH/POTS/ TDM/MOCA ports : 4 / 0 / 0 / 0

CATV ANI/UNI ports : 0 / 0

T-CONTs/GEM ports : 8 / 256

Traffic Schedulers : 8

PQs in T-CONT 1-8 : 8 / 8 / 8 / 8 / 8 / 8 / 8 / 8

IP configuration : not support

Type of flow control : PQ and FLEXIBLY SCHEDULED

TX power cut off : not support

Online/Offline time : 04:43:46 2000/03/02

Up/Down time : 0 day(s) 01 hour(s) 35 minute(s)

3.1.6 show ont brief

This command is used to check the brief information of the ONT.

show ont brief count interface gpon { <interface_list> | all }

show ont brief [ online | offline ] { <ont_id_list> | sn { string-hex <sn_num> | hex

<sn_num> } | interface gpon { <interface_list> | all } }

【Parameter Specification】

ont_id_list: the list of ONT IDs. Such as 0/1 / 1-0 / 2 / 5,0 / 2/10

sn_num: the physical identification of the ONT. There are two formats:
 string-hex format: STRING <13-13>, the first four string is character, then '-' behind, after

that is 8 hexadecimal number, use the "*" matches the corresponding bit of all characters or

hexadecimal numbers;

hex format: STRING <16-16>, all the bits are in hexadecimal number, use the "*" matches

the corresponding bit of all characters or hexadecimal numbers

Interface_list: GPON port list, representing multiple GPON ports. The port number is

represented as slot_num / port_num, slot_num is the slot number, and port_num is the port

number in the slot. Consecutive ports are connected with a minus sign, and non-contiguous ports

are separated by commas, such as: 0 / 1-0 / 5,0 / 8

all: All GPON ports

【Usage】

All modes

【Example】

Check the brief information of ONT

GPON (config) #show ont brief count interface gpon 0/6

Port Online-num Offline-num Total

P0 / 6 1 1 2

Total entries: 1.

GPON (config) #show ont brief interface gpon 0/6

ONT SN Device-type Up / Down-time Status

0/6/1 CMSZ-d2716230 C30-401 0d1h40m Offline

0/6/2 CMSZ-d2716231 C40-100 0d1h40m Online

Total entries: 2.

GPON(config)#show ont brief online interface gpon 0/6

ONT SN Device-type Up-time Running

0/6/2 CMSZ-d2716231 C40-100 0d1h40m NORAML

Total entries: 1.

GPON(config)#show ont brief offline interface gpon 0/6

ONT SN Device-type Down-time Reason

0/6/1 CMSZ-d2716231 C40-100 0d1h40m Poweroff

 Total entries: 1.

3.1.7 show ont description

This command is used to the description of the ONT.

show ont description { <ont_id_list> | sn { string-hex <sn_num> | hex <sn_num> }

| interface gpon <interface_list> }

【Parameter Specification】

ont_id_list: the list of ONT IDs. Such as 0/1 / 1-0 / 2 / 5,0 / 2/10

sn_num: the physical identification of the ONT. There are two formats:

string-hex format: STRING <13-13>, the first four string is character, then '-' behind, after

that is 8 hexadecimal number, use the "*" matches the corresponding bit of all characters or

hexadecimal numbers;

hex format: STRING <16-16>, all the bits are in hexadecimal number, use the "*" matches

the corresponding bit of all characters or hexadecimal numbers

Interface_list: GPON port list, representing multiple GPON ports. The port number is

represented as slot_num / port_num, slot_num is the slot number, and port_num is the port

number in the slot. Consecutive ports are connected with a minus sign, and non-contiguous ports

are separated by commas, such as: 0 / 1-0 / 5,0 / 8

【Usage】

All modes

【Example】

Check the description of ONT 0/6/2

GPON (config) #show ont description 0/6/2

ONT SN Description

0/6/2 CMSZ-d2716231 abcd

3.1.8 show ont profile

This command is used to check the configuration of ONT which is online.

show ont profile { <ont_id> | sn { string-hex <sn_num> | hex <sn_num> } | interfa

ce gpon <interface_list> }

【Parameter Specification】

ont_id: ONT ID number, in the form slot_num / port_num / ont_num, slot_num is the slot

number, port_num is the port number, ont_num is the ONT's index assigned by the OLT

sn_num: the physical identification of the ONT. There are two formats:

string-hex format: STRING <13-13>, the first four string is character, then '-' behind, after

that is 8 hexadecimal number

hex format: STRING <16-16>, all the bits are in hexadecimal number

Interface_list: GPON port list, representing multiple GPON ports. The port number is

represented as slot_num / port_num, slot_num is the slot number, and port_num is the port

number in the slot. Consecutive ports are connected with a minus sign, and non-contiguous ports

are separated by commas, such as: 0 / 1-0 / 5,0 / 8

【Usage】

All modes

【Example】

Check the configuration of ONT

GPON(config)#show ont profile interface gpon 0/6

ONT SN VLAN Us-traffic Ds-traffic Line DBA

0/6/2 CMSZ-d2716231 2 1 1 1 1/2/3

Total entries: 1.

GPON (config) #show ont profile 0/6/2

----------------------------------------------------------------

Unique profile 0/5/100 name GPON16301084

gemport 2 vlan-profile 0 us-traffic-profile 0 ds-traffic-profile 0

gemport 30 vlan-profile 1 us-traffic-profile 1 ds-traffic-profile 1

----------------------------------------------------------------

DBA profile 0 name 20M

Type 2 assured 20480

 ----------------------------------------------------------------

VLAN profile 0 name TRANSLATE_100_TO_2

translate old-vlan 100 new-vlan 2

VLAN profile 1 name TRANSLATE_591_TO_593

translate old-vlan 591 new-vlan 593

----------------------------------------------------------------

US-traffic profile 0 name US_10M

us car cir 10000 cbs 1000 pir 20000 pbs 1000

US-traffic profile 1 name US_20M

us car cir 20000 cbs 1000 pir 20000 pbs 1000

----------------------------------------------------------------

DS-traffic profile 0 name DS_10M

ds car bandwidth 10000 burst 16

DS-traffic profile 1 name DS_2M

ds car bandwidth 2000 burst 16

----------------------------------------------------------------

Line profile 0 name C40-100

device type c40-100

tcont 1 profile dba 0

gemport 2 tcont 1

gemport 30 tcont 1

mapping 0 vlan 100 gemport 2

mapping 1 vlan 591 gemport 30

3.1.9 show ont upgrade-status

 This command is used to check the status of the ONT software upgrading or xml

configuration provisioning.

show ont upgrade-status { image | xml } { <ont_id_list> | all }

【Parameter Specification】

ont_id_list: the list of ONT IDs. Such as 0/1 / 1-0 / 2 / 5,0 / 2/10

all:All the ONTs

【Usage】

All modes

【Example】

Check the status of the ONT software upgrading

GPON (config) #show ont upgrade-status all

ONT Active-version Inactive-version Status

0/6/1 V1.1 V1.0 success

0/6/2 V1.0 V1.1 100%

0/6/3 V1.0 V1.0 crc error

0/6/4 V1.0 V1.0 time out

0/6/5 V1.0 V1.0 offline

0/6/6 V1.0 V1.1 50%

Total entries: 6.

3.2 ONT Remote Management

 ont reboot

 ont upgrade

3.2.1 ont reboot

This command is used to reboot ONT remotely.

ont reboot { <ont_id> | sn { string-hex <sn_num> | hex <sn_num> } }

【Parameter Specification】

ont_id: ONT ID number, in the form slot_num / port_num / ont_num, slot_num is the slot
number, port_num is the port number, ont_num is the ONT's index assigned by the OLT

sn_num: the physical identification of the ONT. There are two formats:

string-hex format: STRING <13-13>, the first four string is character, then '-' behind, after

that is 8 hexadecimal number

hex format: STRING <16-16>, all the bits are in hexadecimal number

【Usage】

Global Configuration Mode

【Example】

Reboot ONT 0/6/2

GPON (config) #ont reboot 0/6/2

3.2.2 ont upgrade

This command is used to upgrade the ONT software version remotely. The ONT will upload

the new software from the OLT and reboot as long as finished. After that you need to commit the

new software to make sure it will be the running software.

ont upgrade { <ont_id_list> | sn { string-hex <sn_num> | hex <sn_num> } }

ont upgrade commit { <ont_id_list> | sn { string-hex <sn_num> | hex <sn_num> }

【Parameter Specification】

ont_id_list: the list of ONT IDs. Such as 0/1 / 1-0 / 2 / 5,0 / 2/10

sn_num: the physical identification of the ONT. There are two formats:

string-hex format: STRING <13-13>, the first four string is character, then '-' behind, after

that is 8 hexadecimal number, use the "*" matches the corresponding bit of all characters or

hexadecimal numbers;

hex format: STRING <16-16>, all the bits are in hexadecimal number, use the "*" matches

the corresponding bit of all characters or hexadecimal numbers

base: OMCI baseline upgrading way. The OMCI packet length is fixed at 48 bytes when the

ONT uploads the software from the OLT

extend: OMCI extended upgrading way. The OMCI packet length can be up to 1980 bytes

when the ONT uploads the software from the OLT

 window_size: Upgrading window size. The software will be divided into many sections when

the ONT uploads the software from the OLT. The OLT will require the ONT to feedback every

several sections and the upgrading window size determines the number of sections between two

feedbacks. In the range of <1-256>, the default is 16

【Usage】

Global Configuration Mode

【Example】

Reboot ONT 0/6/2

GPON (config) #ont upgrade 0/6/2

The ONT will reboot automatically after finishing the transmission of the ONT image, are

you sure (y / n)? [N] y

The ONT is upgrading. Please execute "ont upgrade commit" to activate the new software

after the ONT reboots and registers again.

3.3 ONT Logging Management

 ont-logging

 ont-logging buffer

 ont-logging monitor

 ont-logging prefix

 ont-logging timestamps

 show ont-logging config

 show ont-logging buffer

 clear ont-logging buffer

3.3.1 ont-logging

This command is used to enable ONT logging function.

ont-logging

no ont-logging
【Parameter Specification】

ont_id: ONT ID number, in the form slot_num / port_num / ont_num, slot_num is the slot

number, port_num is the port number, ont_num is the ONT's index assigned by the OLT

sn_num: the physical identification of the ONT. There are two formats:

string-hex format: STRING <13-13>, the first four string is character, then '-' behind, after

that is 8 hexadecimal number

hex format: STRING <16-16>, all the bits are in hexadecimal number

【Usage】

Global Configuration Mode

【Example】

Enable the ONT logging function

GPON(config) #ont-logging

3.3.2 ont-logging buffer

This command is used to enable the ONT log caching function.

ont-logging buffer {<ont_id_list> | all}

no ont-logging buffer {<ont_id_list> | all}

【Parameter Specification】

ont_id_list: the list of ONT IDs. Such as 0/1 / 1-0 / 2 / 5,0 / 2/10

all:All the ONTs

【Usage】

Global Configuration Mode

【Example】

Enable the ONT log caching function

GPON(config) #ont-logging buffer all

3.3.3 ont-logging monitor

This command is used to enable the monitoring function of ONT log.

ont-logging monitor {<ont_id_list> | all}

no ont-logging monitor {<ont_id_list> | all}

【Parameter Specification】

【Parameter Specification】

ont_id_list: the list of ONT IDs. Such as 0/1 / 1-0 / 2 / 5,0 / 2/10

all:All the ONTs

【Usage】

Global Configuration Mode

【Example】

Enable the ONT log monitoring function

GPON(config) #ont-logging monitor all

3.3.4 ont-logging prefix

This command is used to add prefixes in the ONT log. The prefix can be ONT ID or SN or

both.

ont-logging prefix {ontid | sn}

no ont-logging prefix {ontid | sn}

【Parameter Specification】

no

【Usage】

Global Configuration Mode

【Example】

Add a SN prefix in the ONT log

GPON(config) #ont-logging prefix sn

3.3.5 ont-logging timestamps

This command is used to configure the format of timestamp in the ONT log.

ont-logging timestamps {uptime | notime | datetime}

【Parameter Specification】

uptime: the time system running

 notime: no timestamps

datetime: the system time

【Usage】

Global Configuration Mode

【Example】

Configure the format of the timestamps in the ONT log as system time

GPON(config) # ont-logging timestamps datetime

3.3.6 show ont-logging config

This command is used to view the current ONT log management configuration.

show ont-logging config

【Parameter Specification】

no

【Usage】

Global Configuration Mode

【Example】

Check the configuration of ONT logging function

GPON(config) #show ont-logging config

logging state: on

logging timestamps: uptime

logging prefix: ontid: on; sn: on

logging buffer: 0/1 / 1-0 / 16/128

logging monitor:

0: 0/6/1

1: off

2: off

3: off

4: off

5: off
3.3.7 show ont-logging buffer

This command is used to check the current buffer of the ONT log.

show ont-logging buffer {<ont_id_list> | all}

【Parameter Specification】

ont_id_list: the list of ONT IDs. Such as 0/1 / 1-0 / 2 / 5,0 / 2/10

all:All the ONTs

【Usage】

Global Configuration Mode

【Example】

Check the log of ONT 0/1/1

GPON (config) #show ont-logging buffer 0/1/1

00:25:45 0/1/1 GPON-15b00374: eth port 2 links down.

00:25:45 0/1/1 GPON-15b00374: eth port 1 links down.

00:25:42 0/1/1 GPON-15b00374: online.

00:24:25 0/1/1 GPON-15b00374: offline, reason: LOS.

00:15:45 0/1/1 GPON-15b00374: eth port 2 links up.

00:15:45 0/1/1 GPON-15b00374: eth port 1 links up.

00:15:42 0/1/1 GPON-15b00374: online.

00:13:46 0/1/1 GPON-15b00374: offline, reason: NONE.

00:01:34 0/1/1 GPON-15b00374: online.

3.3.8 clear ont-logging buffer

This command is used to clear the current buffer of the ONT log.

clear ont-logging buffer {<ont_id_list> | all}

【Parameter Specification】

ont_id_list: the list of ONT IDs. Such as 0/1 / 1-0 / 2 / 5,0 / 2/10

all:All the ONTs

【Usage】
 Global Configuration Mode

【Example】

Clear the log of ONT 0/1/1

GPON (config) #clear ont-logging buffer 0/1/1