SOLIDWORKS

Getting Started Guide

SOLIDWORKS Electrical FIRST Robotics Edition
Alexander Ouellet
1/2/2015
Table of Contents
INTRODUCTION ............................................................................................................................................. 1
What is SOLIDWORKS Electrical? ............................................................... Error! Bookmark not defined.
Learning Resources ................................................................................................................................... 1
Online Help and Support....................................................................................................................... 1
Setting Up SOLIDWORKS Electrical ........................................................................................................... 2
How do you Apply for SolidWorks Sponsorship?.................................................................................. 2
Enabling SOLIDWORKS Electrical in SOLIDWORKS.................................................................................... 3
SOLIDWORKS ELECTRICAL DESIGN CYCLE ..................................................................................................... 4
Overview .................................................................................................... Error! Bookmark not defined.
UNDERSTANDING THE WORKFLOW ............................................................................................................. 5
Single Line Diagram .................................................................................... Error! Bookmark not defined.
Schematics ................................................................................................................................................ 7
Component Tree ........................................................................................ Error! Bookmark not defined.
The User Interface..................................................................................................................................... 9
PROJECTS .................................................................................................................................................... 10
What are Projects?.................................................................................................................................. 10
Project Elements ..................................................................................................................................... 10
Creating a New Project ........................................................................................................................... 11
Creating a new Library ............................................................................................................................ 12
Creating a New Manufacturer Part ......................................................................................................... 13
SINGLE LINE DIAGRAMS .............................................................................................................................. 15
What are Single Line Diagrams? ............................................................................................................. 15
Creating a Single Line Diagram Symbol................................................................................................... 15
Creating the Symbol ............................................................................................................................ 15
Drafting the Symbol ............................................................................................................................ 17
Creating a Single Line Diagram ............................................................................................................... 19
Inserting a Symbol............................................................................................................................... 19
Sketching Wires................................................................................................................................... 21
SCHEMATICS ............................................................................................................................................... 23
What are Schematics? ............................................................................................................................ 23
 Creating a Schematics Symbol ................................................................................................................ 23
Creating the Symbol ............................................................................................................................ 23
Drafting a Symbols .............................................................................................................................. 24
Creating a Schematic Diagram ................................................................................................................ 25
Inserting a Symbol............................................................................................................................... 25
Inserting a Wire ................................................................................................................................... 27
Adding Wire Numbers......................................................................................................................... 28
Assigning Cables and Harnesses ......................................................................................................... 29
SOLIDWORKS ELECTRICAL 3D…………………………………………………………………………………………………………………29

Inserting a 3D Component ……………………………………………………………………………………………………….29

Opening a Part in SolidWorks……………………………………………………………………………………………………29

Routing Cables …………………………………………………………………………………………………………………………30

GENERATING REPORTS………………………………………………………………………………………………………………………….31
INTRODUCTION

The purpose of this document is to teach new users the

fundamentals of SOLIDWORKS Electrical and assist in the
creation of new projects using SOLIDWORKS Electrical.

What is SOLIDWORKS Electrical?

SOLIDWORKS Electrical is an add-on program which allows you

to design and create documentation for your electrical
schematics which can then be routed in SolidWorks3D CAD. This
allows for added intelligence and design intent in the creation
of new systems and assemblies.

Learning Resources
Online Help and Support

You can learn more about SOLIDWORKS Electrical from our

YouTube Page and from our Facebook Page. You can also visit
the SOLIDWORKS Electrical Website. If you have any question
you can leave a post on our SOLIDWORKS Teacher Blog. You can
also use the SolidWorks FIRST Tutorials

1
Setting Up SOLIDWORKS Electrical

To get SOLIDWORKS Electrical for your team, you first need to

apply to SolidWorks for sponsorship. Once you apply,
SolidWorks will let you have access to the following programs:

 SOLIDWORKS 3D CAD (SOLIDWORKS)

 SOLIDWORKS Electrical
 SOLIDWORKS Simulation
 SOLIDWORKS Composer

How do you Apply for SolidWorks Sponsorship?

To apply for SolidWorks Sponsorship:

1. Click the link to the SolidWorks FIRST Robotics Website.

2. Click the SOLIDWORKS SPONSORSHIP link and fill out
the survey.
3. Once you’ve completed the survey, you will have to
wait between 3 to 5 business days in order for
SolidWorks to approve you or not.
4. Once APPROVED SolidWorks will send you codes and
instruction on how to get your SolidWorks products by
the email you provided.

2
Enabling SOLIDWORKS Electrical in SOLIDWORKS

SOLIDWORKS Electrical has two parts to it:

 SOLIDWORKS Electrical 2D, which is a standalone

program.
 SOLIWORKS Electrical 3D, which is an add-in in
SOLIDWORKS.

To enable SOLIDWORKS Electrical 3D in SOLIDWORKS:

1. Run SOLIDWORKS.
2. Click Tools > Add Ins.
3. Check the ACTIVE ADD-INS check box next to
SOLIDWORKS Electrical to active SOLIDWORKS
Electrical in SOLIDWORKS.
4. Click OK to exit the menu and save your changes.

NOTE: You can set SOLIDWORKS Electrical to automatically run

once SOLIDWORKS 3D CAD runs by checking the START UP check
box next to SOLIDWORKS ELECTRICAL.

3
SOLIDWORKS ELECTRICAL DESIGN
CYCLE

Overview

In SOLIDWORKS Electrical consists of seven main design steps,

assuming you have already acquired your components and
created 3D models for them:

1. Creating a Library
2. Creating Manufactures Parts
3. Creating Symbols
4. Line Diagram
5. Schematics Diagram
6. 3D Representation
7. Wire Harness

By going through these steps SOLIDWORKS Electrical will help

you bring your electrical design ideas to life.

4
Using 2015 FIRST Robotics Electrical Environment

Importing the Environment

Designing a robot using SOLIDWORKS Electrical requires the

proper libraries and settings. This information is contained within
the FIRST Robotics 2015 SOLIDWORKS Electrical Environment.

To Import the environment, open SOLIDWORKS Electrical and

select Unarchive Environment from the Archiving tab under the
file menu.

When prompted, select “FIRST Robotics 2015 SOLIDWORKS

Electrical Environment.twezip”

Continue through the menu and click okay at each prompt until the
finish option appears. Click finish and the environment has been
fully imported.

5
UNDERSTANDING THE
WORKFLOW

Single Line Diagram

Single line diagrams provide an excellent project overview

along with a quick means to create basic cable connections.
Symbols are first placed that represent each major electrical
component. These components can be associated to a
manufacturer’s part at any time. Cables are then drawn to
visually connect components and optionally connect circuits.

6
Schematics

Schematics are built for power and control circuits using

symbols tied to components. Single or multiple wires can be
drawn between symbols and wires are numbered and trimmed
automatically. Origin and destination arrows are created easily
to ensure multi-page schematics are wired correctly.
SOLIDWORKS Electrical also prevents origin – destination
arrows from connecting to the wrong wire type to avoid
connecting ground to power. Additional schematic tools
automate the placement and organization of terminals, PLCs
and black box components.

7
Component Tree

As symbols are added, a Component tree is built dynamically.

Locations can be defined for the project so that components
can be identified with them. This helps with documentation as
well as organization. The component tree can be used in
schematics and 3D to insert their corresponding symbols and 3D
models.

SOLIDWORKS Electrical 3D can be used to assemble

components along with their mechanical counterparts to create
complete 3D models. Finally, wires and cables are routed
automatically along guide lines to layout route locations as well
as calculate lengths.

The symbol and manufacturer part libraries can be tailored to

your needs by removing or importing symbols and parts. Parts
can be added individually as they are used and are shared with
all Electrical users through SQL database.

8
The User Interface
The SOLIDWORKS Electrical user interface is divided up into four
main sections.

The Side Panel provides access to project documents as well as

components, macros and symbols. It also includes a command
tab and options when a command is active.

The Ribbon, or Command Manager menu, contains input

commands sorted into multiple groupings (tabs).

The Graphics Zone is limited to drawing access and editing.

The Status Bar shows the cursor position and allows you to
toggle modes like SNAP on and off.

9
 PROJECTS

What are Projects?

A Project is the collection of the many different types of files
used to create the reports, data and other files that together
fully defines the system.

A Project contains one or more document books and each book

can contain multiple folders to manage the different files
related to that book.

Project Elements
Some important elements of projects to know about when
using SOLIDWORKS Electrical are:

 Project: is the name assigned to the entire project

including all the books and drawing files.
 Book: contains all the documentation that is used to
create the project including folders, drawings and
associated documents. Each project can contain one or
more books.
 Folders: contain data within the Book, and can be used
to categorize data, for greater manageability.
 Drawings: contain different information types that go
to make up the complete project data set, drawings can
contain, schemes, lists, 2D cabinet layouts...
 Cover Page: contains a title block in which user can set
attributes to display information such as the project
name and description, contents of a book. The drawing
tools may be used to add an image.
 Scheme: Scheme drawings contain circuit information
related to the function of the electrical project.
 Line diagram: shows a simplified overview of project
components interconnects and cables used to form
these connections.
 Mixed schema: drawing allows users to mix the data
style of scheme and line diagram type drawings to
produce data rich hybrid designs.
 Drawing lists: contain a variety of project reports
generated as drawings.

10
  Terminal drawings: are automatically created from data
applied to terminals in the project drawing set and
through the Terminals editor.
 2D Cabinet Layouts: are general arrangement layouts
that can be created within SolidWorks Electrical
Schematic to aid in the positioning of components
within a machine, cabinet, installation...
 SolidWorks Cabinet Layouts: allows for the
development of project data in a 3D environment.

Creating a New Project

To create a New Project:

1. Start SOLIDWORKS Electrical 2D.

2. Click Project Manager > New Project .
3. Select the standard you want to use using the
dropdown menu (e.g. ANSI). Click OK to confirm your
selection.
4. Click the English (or the language you want to use) and
click OK.
5. Type in your project information. Give your project a
name and a description by filling out the Name and
Description (English) sections.
6. Click OK when done and a new project will be created.

NOTE: Creating a new project automatically creates multiple

files of several different types. Additional drawings and
other files can be added manually. The structure of a new
project is based on a template. You only need to create an
initial project structure and configure its settings once. It can
then be saved as a template to keep all projects consistent
and to speed up initial design.

11
Creating a new Library

To create a new Library:

1. Run the SOLIDWORKS Electrical 2D standalone

program.
2. The Project Manager will automatically open every time
you launch SOLIDWORKS Electrical 2D. Close the Project
Manager.
3. Click the Library Tab > Libraries Manager.
4. In the Libraries Manager click New to create a new
library.
5. The Library Property Manager should open. Give your
library a name and description. For this guide we will
call the library Custom.
6. Click OK to save you data and create a new library.

12
Creating a New
Manufacturer Part
To create a new manufacturer part that does not yet exist in the
catalog:

1. Click the Library Tab > Manufacturer parts manager.

2. Click Add part in the Manufacturer parts manager

window.
3. Fill in the following sections with information about
your component:
 Part: For the part number.
 Manufacturer: For the name of the
manufacturer
 Class: What type of component you have
(Connector, Relay, Transformer…)
 Library: Which library your component will be
in.
 Type: This should be set as BASE.
 Description (English): The name of the part (e.g.
4 Pin Connector)
4. Click the Add button to start adding circuits to your
component.

Circuits are what give your component life. It defines how many
pins or terminals your component has and what each of those
pins or terminals do.

There are four fields related to circuits:

 Number: This is the number of circuits you have. As you

add more circuits the number increases starting from
zero.
 Type: This is the type of circuit you have. They range
from a variety of type ranging from Ground, Power
supply, Terminals, etc.…
 Terminal Number: This is the number or terminals in
the circuit which share the same type. You can either
give it a name such as GND for or if you have multiple

13
 terminals of the same type, you number them starting
from one with commas after each number (e.g. 1, 2, 3,
4…).
 Group: This helps you to give more information about
the terminal. It is not necessary to be filled out but will
help you document your project.

5. Fill out the information for your circuits and add more
circuits as needed. Click OK to save your work.

14
 SINGLE LINE DIAGRAMS

What are Single Line

Diagrams?
A Line Diagram, or Single Line Diagram, is a simplified
representation of the cabling that will be used in the project. It
shows the original concept of the project, optionally with
drawing graphics, rather than the final result. The single line
diagram is a useful tool for managing components and their
relationships, functionality and connectivity. Cables can be
defined between components within the line diagram.

In a line diagram you use symbolic representation of your

components which most often are images of the component
being used. SOLIDWORKS Electrical comes with an extensive
library of line diagram symbols which you can use. You can also
make your own symbols for components to use in the line
diagram.

Creating a Single Line

Diagram Symbol

Creating the Symbol

To create a Line Diagram Symbol:

1. Click the Library Tab > Symbols Manager.

2. Once the Symbols Manger opens, click New to create a
new symbol.

15
Once you create a new symbol, the symbol properties window
will open. This is where you can enter all the data about your
component. The data entered has a direct impact on how the
symbol will be used and how it will interact with other symbols.

Some of the main fields available are:

 Symbol name: The name of the symbols DWG file.

 Description: This will be displayed when viewing the
symbols through the Thumbnail Mode, if left blank the
Symbol name will be shown.
 Manufacturer/Part: A manufacturer and part that will
be automatically applied to the symbol on insertion.
 Library: The library the symbol will be associated to can
be filtered at a project level to limit different symbol
standards availability in project drawings.
 Symbol type: Defines that command that will allow
access to the symbol, Multi wire symbols are available
when using the Insert Symbol command from the
Schematic tab, for example.
 Classification: Allows association of the symbol to
specific classification, manufacturers parts also have
classification, matching symbol and part classification
assists in part assignment in scheme drawings.
 Unit system: Metric or Imperial, sets the symbols
drawing unit system, this can affect symbol size during
insertion of a mm symbol into a scheme drawing in
inches.

3. Fill in the information associated with the component

you want to use. Make sure to select line diagram
symbols for the Symbol type and Custom (the library
you created earlier) for the Library.
4. Click OK so save the data and create a new symbol. The
symbol should now appear in the Symbol Manager
under the Custom library.

16
 NOTE: You can search for any library by going to the
Filters tab in the Symbols manager and selecting your
library under the Library drop box. Make sure that the
‘In the class:’ box is unchecked when doing this.

Drafting the Symbol

Now that you have created the symbol you now need to create
a visual representation so you know what component the
symbol is representing.

To Draft your symbol:

1. Double click your symbol in the Symbols Manager to

open the drawing window.

When you are in the drawing window, a new tab called Drawing
will appear. This tab will house most of the tools you will need
to make your draft.

2. Click the Drawing tab to bring up the drawing tools.

NOTE: Normally a line diagram symbol draft consists of an

image of the component you are using in real life which is inside
a box. The box is needed so that program knows the boundaries
of the draft.

3. Click on the GRID button to show the grid.

4. Click the SNAP button to turn snap on.

NOTE: The GRID and SNAP tools will make it easier to create
your drafts.

17
TIP: You can right click on either the GRID or SNAP button to
adjust the grid, grid spacing and snap distance.

5. Click Insert Image and browse for the image you are
going to use. Select the image click Open to confirm
your selection. The image you select must be in bitmap
form. The Insert image window should appear. Click OK
in insert your image.

NOTE: The bitmap image should be a 16 color bitmap.

6. To adjust the size and location of the image, click on

one of the corners of the image. Five blue squares will
appear on the image, four are for resizing the image
and one for moving the image.
7. Draw a rectangle around your image making sure that
your image is within the boundary. To do this click the
Rectangle too. The first click is where the upper left
corner will be and the second click will be where the
bottom right corner will be.

Next you need to properly label your draft. To do this we have

to add an attribute. Attributes label your draft with specific
information such as:
 Location of component
 Manufacture’s part number

18
  Manufacture

8. Add an attribute by clicking Edit symbol > Attributes

insertion.
9. Check the check box new to the #TAG attribute in the
Identification folder. Click OK to confirm your selection.
10. Click a location where your want the attribute to
appear.

NOTE: The location doesn’t have to be inside the rectangle that

you drew earlier.

Creating a Single Line Diagram

Inserting a Symbol

To insert a symbol into your Single Line Diagram:

1. Open 03 – Wiring line diagram from the project

drawing list.
2. Click the Line diagram tab > Insert Symbol.
3. The Side Panel will change to a Symbol insertion menu.
To pick a symbol to insert click the Other symbol…
button which will bring up the Symbol selector.

NOTE: The Symbol selector is where you can find any symbol
that SOLIDWORKS Electrical has in its database or any symbols
you add to the database to use in your single line diagrams.

4. Click the Filters tab in the Symbols selector. Make sure

that In the class is unchecked.
5. Select your library from the Library list to bring up all
your components in your library, click the component
you want to insert.
6. Click Select.
7. Place your component symbol where you want it on the
sheet.

19
8. After placing a symbol, the Symbol properties
dialog will be displayed.
9. Leave the default location and root mark.
10. Select the Manufacturer part and circuits tab.
11. Click Search.
12. In the Filters tab select your library from the Library
list.
13. Click Search or enable Automatic refresh
14. Double-click the component that corresponds to
your symbol.
15. Click Select to associate the manufacturer part data
to the symbol.
16. Click OK.

20
Sketching Wires

Since we are using the Single Line Diagram as a representation

of our wire connections, we can sketch simple lines to illustrate
the connections.

The two sketch tools you will mostly need the most to draw
your wire representations are:

 Line Tool .
 Arc Tool .

Sketching a Line

To sketch a Line:

1. From the Drawing tab, click the Line tool.

2. Click where you would like the line to start.
3. Move your mouse and click where you would like the
line to end.
4. You can keep clicking to continue the line. Once you are
finished creating your line click the Esc key to stop
drawing lines.

21
Sketching an Arc

To sketch an Arc:

1. From the Drawing tab, click the Arc tool.

2. Click where you would like the arc to start.
3. Move your mouse and click where you would like the
midpoint of the arc to be.
4. Click a third time where you would like the end point of the
arc to be.

22
 SCHEMATICS

What are Schematics?

A Schematic diagram is used to show the electrical components
and their electrical connections. Schematics may appear in one
or more of the drawings of the book.

Like Single Line Diagrams, SOLIDWORKS Electrical comes with an

extensive library of schematic symbols which you can use and
you can also make your own symbols to use.

Creating a Schematics
Symbol

Creating the Symbol

To create a Schematic Symbol:

1. Click the Library Tab > Symbols Manager.

2. Once the Symbols Manger opens, click New to create a
new symbol. The Symbol properties window will open.

NOTE: See page 15 to view a description of the different

data properties for the symbols.

NOTE: For this section we will be creating a simple 2 Pin

Female Connector.

3. Fill in the information associated with the component

you want to use. Make sure to select Multiwire
symbols for the Symbol type and Custom (the library
you created earlier) for the Library.
4. Click <No reference> under the Part field.
5. The Manufacturer part selection window will appear.
Make sure In the class is unchecked. Select Custom for
Library. Click Search.

23
 6. Double-click the component (the 2 Pin Female
Connector) you are creating the Symbol for.
7. Click OK to create the symbol.

Drafting a Symbols

To Draft your symbol:

1. Double click your symbol in the Symbols Manager to

open the drawing window.
2. Click on the GRID button to show the grid.
3. Click the SNAP button to turn snap on.
4. Set your SNAP and GRID to 1.00 mm spacing.

TIP: You can right click on either the GRID or SNAP

button to adjust the grid, grid spacing and snap
distance.

5. Click the Drawing tab to bring up the drawing tools.

Click the Rectangle tool.
6. Draw a 12 mm X 9 mm rectangle.
7. Click New circuit under the Edit Symbol tab to add
terminals to your connector.
8. The New circuit window will open. Enter 2 for the
Number. Select Aux. female pin for Circuit type. Make
sure that you have Disconnectable selected for
Information transmission.
9. Click OK.

Since we are making a 2 Pin Connector that means we will

have two different circuits attached to the connector. Each
circuit will have two nodes to connect the two ends through
the connector.

10. Right Click Circuit: 0 – Aux. female pin in the Side

Panel, New connection point > Incoming/Outgoing.
11. Click a location in the upper left corner of the rectangle
so that the bigger black circle is outside the rectangle
while the smaller white circle is inside the rectangle.

TIP: You can right-click to rotate the node.

24
 12. Right Click Circuit: 0 – Aux. female pin in the Side
Panel, New connection point > Incoming/Outgoing.
13. Click a location in the lower left corner of the rectangle
so that the bigger black circle is outside the rectangle
while the smaller white circle is inside the rectangle.

Now when you use the symbol in your schematic anything

attached to these two nodes will be connected to each
other.

14. Repeat steps 10-13 but making connections for Circuit:

1 – Aux. female pin.
15. Click Attributes insertion in the Edit symbol tab.
16. Check the boxes next to #TAG and #REF_DES_2 in the
Identification folder. Click OK.
17. Click a location next to your symbol.
18. Save and close your symbol.

Creating a Schematic
Diagram

Inserting a Symbol

To insert a symbol into your Schematic:

1. Open 04 – Electrical scheme from the project drawing

list.
2. Click the Schematic tab > Insert Symbol.
3. The Side Panel will change to a Symbol insertion menu.
To pick a symbol to insert click the Other symbol…
button which will bring up the Symbol selector.
4. Click the Filters tab in the Symbols selector. Make sure
that In the class is unchecked.
5. Select your library (Custom) from the Library list to
bring up all your components in your library, click the
component you want to insert (2 Pin Female
Connector).
6. Click Select.
7. Place your component symbol where you want it on the
sheet.

25
8. After placing a symbol, the Symbol properties dialog
will be displayed.
9. Leave the default location and root mark.
10. Select the Manufacturer part and circuits tab.
11. Click Search.
12. In the Filters tab select your library from the Library
list.
13. Click Search or enable Automatic refresh
14. Double-click the component that corresponds to your
symbol.
15. Click Select to associate the manufacturer part data to
the symbol.
16. Click OK.

26
 Inserting a Wire

Now that you have placed your components in your schematic,

it’s time to add wire connection between your components. To
add wires:

1. Click Draw single wire type in the Schematic tab.

2. The Side Panel should show the Electrical wire
manager. Click the … Browse button.
3. The Wire style selector will open. Here you can select
what type of wire you would like to use. Click the
Command wire and then click Select.
4. Click on a node of a component to start your wire. You
can click to add bends to the wire. Click on a second
node to end your wire and create a connection.
5. When you are done drawing wires, press the Esc key on
your keyboard to stop using the wire tool.

Note: The wire connection will

automatically end when a positive
connection is made

27
Adding Wire Numbers
SolidWorks Electrical can be configured to a variety of
wire numbering conventions. These can include sheet,
row and column numbers, static text, origin and
destination component information among other data.
These options are selected via the Wire Style Manager.

Note: You can hide and show wire

numbers on any wire line by right-
clicking and toggling Show/hide wire
marks.

28
Assigning Cables and Harnesses
As you learned earlier cables are used in single line diagrams to
connect various components to one another. These cables have the
additional ability to connect circuits aside from simply creating visual
connections. Harnesses are groupings of wires and or cables which
are routed together to create simplified designs.

Once components are connected, a purchasable cable with

predefined cores can be associated to the connection from the
existing part library. As components are assigned on each end of the
cable the connectivity between the components and the cable will be
created as a cabling detail

To assign a cable:

1. Right click the cable

2. Select Detailed Cabling to open the Detailed Cabling dialog
3. Select the wires with “?” assigned in the origin column
4. Drag the selected wires to the terminal column for the
desired component
5. Close the dialog
6. From the File tab, click Save to ensure changes are saved to
the project

29
 SolidWorks Electrical 3D
Inserting 3D Components:

As soon as an electrical assembly is created in SolidWorks, the

Electrical Component Tree displays in the Property Manager pane on
the left. Components that already have 3D models will display those
parts under the component mark.

Opening a part in SolidWorks:

1. From the SolidWorks Electrical Menu, select the Projects

Manger.
2. Select the project highlighted in red and select open
3. Expand the feature tree on the left and double click the 3D
model icon.

30
 Routing Cables:

After inserting components into your SOLIDWORKS assembly, the

associated cable and wire routes can be created. SOLIDWORKS Electrical
provides an Electrical Component Wizard to walk through the required setup of
parts to include wire and cable points and mate references to help you use your
own parts or downloaded components.

1. Select the Route Cables command from the SolidWorks

Electrical 3D Command Manager tab
2. Select SolidWorks Route as the route type
3. Select Use Splines
4. Select All Components
5. Set Routing parameters
6. Click the check mark

31
 Generating Reports
SolidWorks Electrical maintains a database of information about components,
wires, cables and assemblies within a project. A variety of reports are available
to share and organize this data. Drawings with this data can be easily shared and
edited.

To generate a report:

1. Select the Project Tab in the SolidWorks Electrical Application

2. Click Reports to open the Reports Manager
3. Click the reports to review the data
4. To generate drawings, click Generate Drawings
5. Select each report listed and click OK
6. Click Close

32