GENERAL LADDER

INSTRUCTIONS

SAFETY IN EVERY STEP

SAFETY IN EVERY STEP

When you choose a ladder from Wibe Ladders

there’s one thing you can be sure of. Every fitting,
every material and every solution has been exam-
ined in the minutest detail and carefully designed to
ensure your safety. This runs throughout the whole
of our extensive range, from our sturdy trestle steps
and tradesmen’s ladders to scaffolding and escape
ladders.

For maximum safety you, the user, also need to

contribute. This folder presents the basics that you
need to know regarding ladders, from performing
maintenance to erecting and using them correctly.

These ladder instructions are in accordance with

EN 131-3:2007.
CONTENT
CHOOSE THE RIGHT PRODUCT 1
USE THE RIGHT ACCESSORIES FOR EVEN GREATER SAFETY 2
SAFETY YOU CAN RELY ON 3
THE MOST COMMON CAUSES FOR ACCIDENTS 4
BEFORE USE 5
POSITIONING AND ERECTING THE LADDER 5
USING THE LADDDER 7
SYMBOLS 8
INSPECTIONS, STORAGE & MAINTENANCE 9
FIBREGLASS LADDERS 11
CHOOSE THE RIGHT PRODUCT
The basis of working safely is to choose the right product for the right task.
It all depends how often you use it and how heavy the work is that you intend to carry out.

PROF+
SAFETY
VERY HEAVY WORK

For more challenging applications

Additional anti-slip protection, well-pro­portioned
locking mechanisms and rough-textu­red anti-skid
devices give these p ­ roducts stability and good
anti-skid c­ haracteristics. The products well exceed
the requirements contained in standards and wor-
king environment regulations.

PROF
HEAVY WORK

For everyday use

Strong aluminium profiles, well-proportioned stan-
ding surfaces and treads make these products sui-
table for everyday use. The products meet the re-
quirements contained in standards and Swedish
working environment regulations.
LIGHT WORK

HOME
For less challenging applications
These products are user-friendly, easy to carry and
store, and therefore suited for lighter work indoors
FREQUENCY OF USE and for occasional work outdoors. Th ­ e products
RARELY OFTEN VERY OFTEN
meet the ­requirements contained in standards
and Swedish working environment regulations.

RIGHT WORKING HEIGHT – RIGHT ERGONOMICS

Low heights Trestle steps and step Moderate heights Step ladders Serious heights Ladders for
stool ladders for working at low and working platforms for working ­accessing roofs for example, and
heights, such as on electrical instal- at slightly higher heights. scaffolding for working at height.
lations or for domestic use.

APPROVED FOR A GOOD WORKING ENVIRONMENT

A number of selected Wibe Ladders trestles and ladders carry a ”Good Work Environment label”. It is the result of Wibe Ladders colla-
boration with the RS-group consisting of NCC, Veidekke, Svevia, Skanska, PEAB and JM, in an initiative that aims to increase user safety
of trestles, ladders and platforms. Basically it’s about contributing to safe work environments and the elimination of ”hazardous” pro-
ducts from construction sites over time. Wibe Ladders became involved in the project, as the leading supplier of ladders and trestles,
and has together with the partners developed a selection of products that meet all the demands. All products that carry the ”Good
Work Environment label” exceed the legislative demands and EU guidelines. Each product is the result of years worth of knowledge,
experience and product development that has lead up to the highest possible quality and safety according to today’s standards.

It’s not certain that a ladder is the best choice. Especially

if you will be working with both hands, use a lot of force,
lift heavy or work over a large area. The ground can also be THINK BEFORE
too slippery or too uneven for erecting a ladder on. Altern­
• At what height will you work?
ative choices could be a sky lift or a scaffold. But there is • Will you use both hands?
also easier equipment like for example trade scaffolding • Will you use force?
or working platforms. We also have rolling towers in our • Will you work for a longer time period?
range. Contact our customer service if you want more infor-
mation about what to use when working at heights.
USE THE RIGHT
ACCESSORIES FOR
EVEN GREATER SAFETY
Wibe ladders offers a wide variety of accessories for your ladders that increases your safety and makes your work more comfortable and
efficient. A few products are presented here below but for a more complete presentation you can visit our website www.wibeladders.com.

One of the most common accidents when working on ladders is that Another common cause for accidents is that the ladder is unstable
the top of the ladder slides sideways. Therefore Wibe Ladders offers because it has been placed on uneven or unstable ground. We have
a number of solutions for securing the ladder at the top. a number of products that helps to keep both ladders and trestles
more stable on uneven ground.

Using a movable standing plate gives you a safer and more comfort- The tool holder lets you put your tool away so you can use your
able stance on the ladder and it folds away so you can easily climb hand for other tasks and with extra hand rails can give you a more
past it. safe and comfortable grip on the ladder.

LEVELLING SAFETY LEGS

With Wibe Ladders' safety legs levelling is made easy, and both top slide and base slide is
prevented. No drilling is required to fit them, and they are easily locked in closed or open
position by means of a knob. When being transported they lie along the ladder's side, tak-
ing up a minimum of space.
• Increase ladder width by 400 mm per side.
• The result is that ladders can be erected even if there are differences of surface level; can be vertically
adjusted through 0–300 mm.
• When transported, the supporting legs are folded parallel to the sides so as not to take up space.
• Anti-skid devices for extra safety.
SAFETY YOU CAN RELY ON.
All our products are subjected to testing by SP – the Technical Research Institute of Sweden – for type
approval in accordance with current standards. In addition, we also regularly perform our own tests,
­supervised by a third party agency, so that we can be sure that all our products meet the high standards
we claim of them. You see, for us there is in only one thing that counts – that you should be able to trust
us to put safety first at each and every step.
The Swedish Work Environment Act contains regulations governing the duties of employers and other
persons responsible for safety in respect of promoting safety and preventing accidents in the workplace.
Regulation AFS 2004:3 of the Swedish Work Environment Authority details the requirements and obligations
governing the working environment in terms of ladders and trestle steps. All of our products meet these high
requirements and are therefore permitted to carry a label certifying that the ladder has been approved.

TYPE TESTED
SP, the Technical Research Institute of Sweden, has the task of audi-
ting products and structures to ensure they meet safety and envi-
ronmental requirements. SP applies the provisions of both Swedish
and international standards. For ladders, the EN 131 European
Standard applies, as well as the rather more stringent regulations of
Swedish Standard SS 2091.

TYPE TESTING OF LADDERS, TRESTLE STEPS

AND STEP STOOL LADDERS
When SP inspects ladders, it uses European Standard
EN 131 as well as the rather more stringent regulations
of Swedish Standard SS 2091. These requirements are
imposed by the Swedish Work Environment Authority in
Regulation AFS 2004:3 to protect your safety. All of our
ladders, trestle steps and step stool ladders meet these
high requirements and are therefore permitted to carry
a label certifying that the ladder has been approved. Our
certificate for portable ladders bears the number 102 102.

TYPE TESTING OF SCAFFOLDING

Our scaffolding is type tested to AFS 1990:12 and appro-
ved to Swedish Standard SSHD 1004, load class 3. Our
certificates for scaffolding have the following numbers:
249 401, 249 402, 249 403, 249 405, 102 104 and
102 105.

TESTING OF ROOF PRODUCTS

SP, the Technical Research Institute of Sweden, tests and
certifies roof safety products. A description of the require­
ments is contained in SP’s “Certification Rules for Roof
Safety Products”, SPCR 014. Once these requirements are
met, the products are awarded the P-mark. Our certificate
for roof safety products bears the number 102 101.

P-TESTING
The P-mark means that, as a minimum, the product meets
statutory and authority requirements, and, in most cases,
even more stringent requirements. The P-mark means
firstly that the product has been type-tested, and secondly
that the manufacturer’s own inspections and testing are
monitored by SP. Don’t forget to ask for the P-mark if you
want to buy a quality product. The certification rules for
P-marking of portable ladders are described in SPCR 064.
Our P-testing certificate carries the number 102 103.
THE MOST COMMON CAUSES FOR ACCIDENTS
If you know the causes for accidents you have a better chance of avoiding them. For leaning ladders the
most common type of accident is that the ladders slips against the surface. Either the bottom slides
outwards or the top slides sideways. These types of accidents make up about 75% of all accidents. For
standing ladders the by far most common accident is that the ladder stands unsteady on uneven ground or
that the ground is so weak that it gives way. Below follows a list of the most common causes for accidents
and risk to take into account when working on ladders.

Loss of stability:
• Incorrect positioning of the ladder (such as incorrect angle for leaning ladder or not fully opening a
standing ladder).
• Slide outwards at the bottom (such as bottom of the ladders sliding away from the wall).
• Side slip, falling sideways and top flip (such as overreaching or fragile top contact surface).
• Condition of the ladder (such as missing anti-slip feet).
• Stepping off an unsecured ladder at height.
• Ground conditions (such as unstable soft ground, sloping ground, slippery surfaces or contaminated
solid surfaces).
• Adverse weather conditions (such as windy conditions).
• Collision with the ladder (such as vehicle or door).
• Incorrect choice of ladder (such as too short, unsuitable task).

From handling:
• Transferring the ladder to the work position.
• Erecting and dismantling the ladder.
• Carrying items up the ladder.

Slip trip and fall of user:

• Inappropriate footwear.
• Contaminated rungs or steps.
• Unsafe user practices (such as climbing 2 rungs at time, sliding down stiles).

Structural failure of ladder:

• Condition of the ladder (such as damaged stiles, wear).
• Overloading the ladder.

Electrical hazards:
• Unavoidable live working (e. g. fault finding).
• Positioning ladders too close to live electrical equipment (such as overhead power lines).
• Ladders damaging electrical equipment (such as covers or protective insulation).
• Incorrect selection of type of ladder for electrical work.
BEFORE USE
• Ensure that you are fit enough to use a ladder. Certain
medical conditions or medication, alcohol or drug
abuse could make ladder use unsafe.
• When transporting ladders on roof bars or in a truck,
ensure they are suitably placed to prevent damage.
• Inspect the ladder after delivery and before first use to
confirm condition and operation of all parts.
• Visually check the ladder is not damaged and is safe to
use at the start of each working day when the ladder is
to be used.
• For professional users regular periodic inspection is
required.
• Ensure the ladder is suitable for the task.
• Do not use a damaged ladder.
• Remove any contamination from the ladder, such as
wet paint, mud, oil or snow.
• Before using a ladder at work a risk assessment should
be carried out respecting the legislation in the country
of use.
• Follow the instructions.

POSITIONING AND ERECTING THE LADDER

• Ladder shall be erected at the correct position, such as
the correct angle for a leaning ladder (angle of inclina-
tion approximately 1:4 or 75 degrees) with the rungs
or treads level and complete opening of a standing
ladder.
• Locking devices, if fitted, shall be fully secured before
use.
• Ladder shall be on an even, level and unmovable base.
• Leaning ladder should lean against a flat non-fragile
surface and should be secured before use, e.g. tied or
use of a suitable stability device.
• Ladder shall never be repositioned from above (while
standing on the ladder).
• When positioning the ladder take into account risk of
collision with the ladder e.g. from pedestrians, vehicles
or doors. Secure doors (not fire exits) and windows
where possible in the work area.
• Identify any electrical risks in the work area, such as
overhead lines or other exposed electrical equipment.
• Ladder shall be stood on its feet, not the rungs or
steps.
• Ladder shall not be positioned on slippery surfaces
(such as ice, shiny surfaces or significantly contamin­
ated solid surfaces) unless additional effective
measures are taken to prevent the ladder slipping or
ensuring contaminated surfaces are sufficiently clean.
USING THE LADDER

• Do not exceed the maximum total load for the type of ladder.
• Do not overreach; user should keep their belt buckle (navel) inside the stiles and both feet on
the same step/rung throughout the task.
• Do not step off a leaning ladder at a higher level without additional security, such as tying off or
use of a suitable stability device.
• Do not use standing ladders for access to another level.
• Do not stand on the top three steps/rungs of a leaning ladder.
• Do not stand on the top two steps/rungs of a standing ladder without a platform and hand/
knee rail.
• Do not stand on the top four steps/rungs of a standing ladder with an extending ladder at the
top.
• Ladders should only be used for light work of short duration.
• Use non-conductive ladders for unavoidable live electrical work.
• Do not use the ladder outside in adverse weather conditions, such as strong wind.
• Take precautions against children playing on the ladder.
• Face the ladder when ascending and descending.
• Keep a secure grip on the ladder when ascending and descending.
• Do not use the ladder as a bridge.
• Wear suitable footwear when climbing the ladder.
• Avoid excessive side loadings e.g. drilling brick and concrete.
• Avoid work that impose a sideways load on standing ladders, such as side-on drilling through
solid materials (e.g. brick or concrete).
• Do not spend long periods on a ladder without regular breaks (tiredness is a risk).
• Leaning ladders used for access to a higher level should be extended at least 1 m above the
landing point.
• Equipment carried while using a ladder should be light and easy to handle.
• Maintain a handhold whilst working from a ladder or take additional safety precautions if you
cannot.
• Do not be more than one person on the ladder.

Bracing and anchorage H>5m

The following types of ladder may only be used if they H>3m
are braced or anchored properly.
H>2m
• Leaning ladders longer than 5 m.
• Standing ladders with a platform and handrail and
where the platform is more than 2 m in height.
• Any other standing ladder higher than 3 m.
SYMBOLS
Leaning ladders
a) Read the instructions
b) Maximum load
c) Correct angle of erection
d) Erect on a level base
e) Do not over-reach
f) Ensure ground is free from contaminant
g) Erect on a firm base
h) Ladder extension above landing point
i) Do not step off the side of a ladder
j) Use the ladder the correct way up [only if necessary due to design of ladder]

a b c d e

f g h i j

Standing ladders
k) Read the instructions
l) Maximum load
m) Erect on a level base
n) Fully opened before use
o) Do not overreach
p) Erect on a firm base
q) Do not step off the side of a ladder
r) Ensure restraint devices are engaged [if fitted]

k l m n o

p q r
INSPECTIONS, STORAGE & MAINTENANCE

Always inspect the ladder before use.

Damaged part shall be replaced, e.g. end protection.

Damaged ladders that cannot be repaired shall be destroyed.

CHECK THAT:
• The ladder stiles are NOT damaged by e.g. transportation or
handling.
• Steps or rungs are NOT damaged by e.g. transportation or
handling.
• Steps or rungs are NOT contaminated with e.g. wet paint,
mud, oil or snow.
• The connection between steps and stiles, or the connection
between rungs and stiles are NOT damaged by e.g. transpor-
tation or handling.
• End protections are NOT worn down or contaminated.
• Locking mechanims are NOT damaged by e.g. transport or
handling.
• Opening/closing restraint devices are NOT damaged by e.g.
transport or handling.
• Hinges are not damaged.
• Asseories are correctly assembled and NOT damaged.

STORAGE
• Ladders should be stored in a suitable way to prevent dam-
age.
• Be ware – stiles, steps, rungs, locking mechanisms should
not be exposed to strikes or to fall over. Deformations can
weaken the construction and be a risk.

REPAIR
• Parts screwed to the construction, or alike, may be replaced
if conducted in accordance with valid assembling instruc-
tion.
• Parts that are permanently fitted to the constructions should
not be replaced by an unauthorized person.
• Repair of parts permanently fitted to the construction should
be conducted by the manufacturer.
 5
8
4 6

6 2
0
2
3 3
7
0

1 7 1

STEP LADDER COMBINATION LADDER

9 6 4 8
10

3 7
0
2
0
2 0
3 6

7 2 7
1 1 1

WORK PLATFORM TRESTLE LEANING LADDER

Ladder part Inspect

0. Ladder stiles Buckles, cracks, fractures or other external influence that affects ladder stability/strenght must not
exist on the ladder stile.
1. End protection/Wheels End protection/wheels must exist. End protection must not be filled with dirt or worn down. Fastening
of en protection/wheel must be solid/intact. Wheel with locking mechanism should have a functioning
locking mechanism. Wheel must not be deformed.
2. Connection steps/Rungs Fastening of steps/rungs must be solid intact.
3. Opening/Closing restraint Hinges, nylon strap or alike should be in proper condition. Fastening should be solid intact.
4. Platform The fastening of the platform must be solid/intact. The platform must lock when unfolded and give
slip resistance. Must not be deformed or contaminated by e.g. oil/lubricate/paint.
5. Tool tray/Knee support Tool tray/knee support must not be damaged. Fastening must be solid/intact.
6. Joint/Hinge/Locking Fastening of joint, hinge, locking must be solid/intact. The joint should not fit loosely. Locking should
lock properly. No defect locking mechanism accepted.
7. Steps/Rungs Steps and rungs must not be deformated. Buckles, cracks, fractures that affects the step or rung
strength must not exist. Rungs/steps must not be contaminated by e.g. oil/lubricate/paint.
8. Fittings/Hooks etc. Fastening of fitting, hooks must be solid/intact. Fittings and hooks must not be bent, cracked, defor-
mated and should work properly.
9. Rail/Handrail Fastening of rail, handrail must be solid intact. Rail and handrail must not be deformated.
10. Braces Fastening of braces must be solid/intact. Braces must not be deformated.
11. Accessories Accessories must be mounted in accordance with intruction. Fastening of accessories must be solid/
intact. Accessories must have proper functionality.
FIBREGLASS LADDERS
Fiberglass ladders from WIBE LADDERS are manufactured
by glass fibre reinforced polyester. The same material as
used for car bodies and car roof boxes. Fiberglass is a
strong non-conductive material suitable for use in electric
environment and highley corrosive environments. The fiber-
glass ladders are tested according for voltage sensitivity
for 30kV according to SS-EN 61478. When using Fibreglass
ladders there are a few extra things that you need to con-
sider:

INSPECTION
• Check the ladders regularly to ensure the fibreglass is not cracked or dam-
aged.
• A ladder with any visible cracks in the fibreglass material should immedi-
ately be scrapped.
• If you are not sure if your ladder is safe, please contact the manufacturer.

STORAGE
• Prevent ladders from accidentally dropping or falling over.
• Fibreglass ladders should be handled with care and stored properly to
prevent damages.
• NOTE! Fibreglass is sensitive to shock and pressure.

MAINTENANCE/REPAIR
• Using the ladder when any of the brackets are loose will result in quick wear
of the material, and the fibreglass may deteriorate to a point where the lad-
der can not be repaired.
• Brackets that are bent or damaged may be replaced, depending on the
fastening method. Please contact the ladder manufacturer for more infor-
mation.
• Any loose nuts and bolts should be tightened enough to remove any play in
the connection.
• Do not tighten the nut to hard. Over-tightening the connection may result in
cracking of the fibre glass profile.
• Parts screwed to the construction, or alike, may be replaced if conducted in
accordance with valid assembling instruction.
• Parts that are permanently fitted to the constructions should not be re-
placed by an unauthorized person.
• Repair of parts permanently fitted to the construction should be conducted
by the manufacturer.
• Drilling of new holes or any other modifications of the ladder does result in
void of type approval.
 Wibe Ladders
Box 145
571 22 NÄSSJÖ
SWEDEN

www.wibeladders.com