Product Data: HEMPADUR 37620

Product Data
HEMPADUR 37620
37620: BASE 37629: CURING AGENT 97620

Description: HEMPADUR 37620 is a two-component, amine cured phenolic epoxy paint, which cured to provide
excellent resistance to acidic environments.
Recommended use: For corrosion protection of steel in atmospheric acidic environments such as electrowinning plants,
coking works, pickling shops, electroplating plants, dye mills, wood-pulp works, tanneries and oil
refineries. Not intended for continuous contact or immersion with acidic solutions.
Service temperature: Ambient temperature in acidic environments.
Availability: Not included in Group Assortment. Availability subject to special agreement.
PHYSICAL CONSTANTS:
Shade nos/Colours: 11621*/ Grey. see REMARKS overleaf
Finish: Glossy
Volume solids, %: 100
Theoretical spreading rate: 4 m2/l [160.4 sq.ft./US gallon] - 250 micron/10 mils
Flash point: 128 °C [262.4 °F]
Specific gravity: 1.3 kg/litre [11.1 lbs/US gallon]
Dry to touch: 6 approx. hour(s) 20°C/68°F
Fully cured: 7 day(s) , 20°C/68°F. see REMARKS overleaf
VOC content: 48 g/l [0.4 lbs/US gallon]
Shelf life: 1 year (25°C/77°F) from time of production. Depending on storage conditions, mechanical stirring may
be necessary before usage.
- *other shades according to assortment list.
- The physical constants stated are nominal data according to the HEMPEL Group's approved formulas.
APPLICATION DETAILS:
Version, mixed product: 37620
Mixing ratio: BASE 37629: CURING AGENT 97620
2:1 by volume
Application method: Airless spray / Brush (touch up)
Thinner (max.vol.): Do not dilute.
Pot life: 40 minute(s) , 20°C/68°F or 30 minutes , 30°C/86°F.
Nozzle orifice: 0.015 - 0.017 "
Nozzle pressure: 250 bar [3625 psi]
(Airless spray data are indicative and subject to adjustment)
Cleaning of tools: HEMPEL'S TOOL CLEANER 99610
Indicated film thickness, dry: 250 micron [10 mils] see REMARKS overleaf
Indicated film thickness, wet: 250 micron [10 mils]
Overcoat interval, min: According to specification.
Overcoat interval, max: According to specification.
-
Safety: Handle with care. Before and during use, observe all safety labels on packaging and paint containers,
consult HEMPEL Safety Data Sheets and follow all local or national safety regulations.
Date of issue: January 2018 Page: 1/2

Product Data
HEMPADUR 37620
SURFACE PREPARATION: New steel: Remove oil and grease etc. thoroughly with suitable detergent. Remove salts and other
contaminants by high pressure fresh water cleaning. Abrasive blasting to Sa 2½ (ISO 8501-1:2007).
Minimum surface profile corresponding to Rugotest No. 3, BN11a, Keane-Tator Comparator, 5.5 G/S,
or ISO Comparator Coarse (G) - or as per specification for the subsequent coat(s). Otherwise
according to specification. After blasting, clean the surface carefully from abrasives and dust.
Feather edges to sound and intact areas. Dust off residues. Touch up to full film thickness.
APPLICATION CONDITIONS: Use only where application and curing can proceed at temperatures above: 10°C/50°F. The steel
temperature must never drop below this limit until full curing has taken place. The temperature of
the paint itself must be above 15°C/59°F, best results are obtained at 17-23°C/62-73°F. Apply only on a
dry and clean surface with a temperature above the dew point to avoid condensation. In confined
spaces provide adequate ventilation during application and drying.
See separate APPLICATION INSTRUCTIONS
PRECEDING COAT: HEMPADUR 37620
SUBSEQUENT COAT: HEMPADUR 37620
REMARKS:
Colours/Colour stability: May attain a reddish shade in very acidic environments. This is a common feature of all 100% solids
novolac epoxy products and has no detrimental effect on performance.
Overcoating intervals: If the maximum overcoating interval is exceeded, roughening of the surface is necessary to ensure
intercoat adhesion.
Note: HEMPADUR 37620 For professional use only.
ISSUED BY: HEMPEL A/S 3762011621
This Product Data Sheet supersedes those previously issued.

For explanations, definitions and scope, see “Explanatory Notes” available on www.hempel.com. Data, specifications, directions and recommendations given in this data sheet
represent only test results or experience obtained under controlled or specially defined circumstances. Their accuracy, completeness or appropriateness under the actual conditions
of any intended use of the Products herein must be determined exclusively by the Buyer and/or User.
The Products are supplied and all technical assistance is given subject to HEMPEL's GENERAL CONDITIONS OF SALES, DELIVERY AND SERVICE, unless otherwise expressly agreed
in writing. The Manufacturer and Seller disclaim, and Buyer and/or User waive all claims involving, any liability, including but not limited to negligence, except as expressed in said
GENERAL CONDITIONS for all results, injury or direct or consequential losses or damages arising from the use of the Products as recommended above, on the overleaf or otherwise.
Product data are subject to change without notice and become void five years from the date of issue.
Date of issue: January 2018 Page: 2/2

Product Data: HEMPADUR 37620

Uploaded by

Copyright:

Available Formats

Product Data: HEMPADUR 37620

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Product Data: HEMPADUR 37620

Uploaded by

Copyright:

Available Formats

Product Data

37620: BASE 37629: CURING AGENT 97620

Date of issue: January 2018 Page: 1/2

This Product Data Sheet supersedes those previously issued.

Date of issue: January 2018 Page: 2/2

You might also like