Scribd
Upload
177 views

Calibration Procedure For Melting Point Apparatus: IA 9100, 9200 and 9300

The document provides instructions for annually calibrating a melting point apparatus. It involves using a calibration kit and standard chemicals to check the current calibration. If needed, recalibration is performed by adjusting potentiometers on the circuit board until the readings match the certified melting points of the standard chemicals. The process is repeated until the high and low readings are accurately calibrated.

Uploaded by

SUSIANA SUSIANA
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
177 views

Calibration Procedure For Melting Point Apparatus: IA 9100, 9200 and 9300

The document provides instructions for annually calibrating a melting point apparatus. It involves using a calibration kit and standard chemicals to check the current calibration. If needed, recalibration is performed by adjusting potentiometers on the circuit board until the readings match the certified melting points of the standard chemicals. The process is repeated until the high and low readings are accurately calibrated.

Uploaded by

SUSIANA SUSIANA
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Calibration Procedure for Melting Point Apparatus:

IA 9100, 9200 and 9300

Calibration must be carried out annually, or whenever the performance of the apparatus is suspected,
e.g. when similar successive test produce markedly divergent results.

The apparatus must either be returned to the dealer for calibration, or calibration must be carried out in
the following manner, using Calibration Kit AZ6730 and the standard chemicals Carbazole (AZ9118)
and P-nitrotoluene (AZ9218).

To check if the unit is still in calibration proceed as follows:

a) Switch the unit on and ensure the instrument components are in the stable condition

b) Perform a melt with each standard chemical and note the reading

c) Compare the results obtained with the melting points shown on the certificates supplied
with each chemical and ascertain whether the unit performs within acceptable limits

If it is decided that re-calibration is required proceed as follows:

1. Switch off the unit and allow it to cool

2. Disconnect Power supply from the rear of the unit

3. Invert the unit and remove the three screws securing the base plate to the body

4. Place the unit on the bench the correct way up taking care not to let the base fall from the unit. Lift
the body from the base plate

5. Turn the body on its side and placed it on the bench to the right of the base plate

6. Remove the two pin connector from PL1 2A on the printed circuit board

7. Plug in the calibration box into pin connector PL 12A

8. Switch the selector switch to the LO position

9. Insert the power plug on the instrument and switch on

10. Allow the instrument to re-stabilise. It should not be necessary to go through the ‘Set-point’
procedure again at this stage. 2 to 3 minutes should suffice to ensure stabilisation.

11. Adjust the LO knob until the display shows the actual melting point obtained in b) above for the
standard sample of p-nitrotoluene.

12. Switch the selector switch to the Hi position

13. Adjust the HI knob until the display shows the actual melting point obtained in b) above for the
standard sample of Carbazole

14. Adjust VR1 on the PCB with the trim tool provided untilt the display reads the melting point o
Carbazole as quoted on the Calibration Certificate provided with the sample.

15. Switch the selector switch to LO

16. Adjust VR3 on the PCB with eth trim tool until the display reads the melting point of p-nitrotoluene
as quoted on the Calibration Certificate provided with the sample
17. Repeat steps 14 to 18 until no further adjustment to VR1 and VR3 are required when the switch is
changed from Hi to LO

18. The unit is now calibrated

19. Unplug the calibration Box PL12A and replace the connector removed in stage 6

20. Remove the power supply plug and replace the base. Check the calibration again using Standard
Chemicals as in b) and c) and repeat the procedure if necessary

You might also like