CPC 100 User Manual v1.43

Manual Information Contact Information / Technical Support
Article Number VESD0601 - Manual Version: CPC100LITE.AE.6

Europe, Africa, Middle East
With respect to the functionality of the CPC 100 software, this manual refers to the version
V 1.43. OMICRON electronics GmbH
Oberes Ried 1,
© OMICRON electronics 2010. All rights reserved.
A-6833 Klaus, Austria
CPC 100 This product includes software developed by Intrinsyc Software.

Phone:
E-Mail:
+43 5523 507-333
[email protected]
User Manual Web: www.omicron.at
Asia, Pacific
OMICRON electronics Asia Ltd.
Suite 2006, 20/F, Tower 2
The Gateway, Harbour City
Kowloon, Hong Kong S.A.R.
Phone: +852 2634 0377
E-Mail: [email protected]
This manual is a publication of OMICRON electronics GmbH. Web: www.omicron.at
All rights including translation reserved. Reproduction of any kind, for example, photocopying, North and South America
microfilming, optical character recognition and/or storage in electronic data processing systems,
requires the explicit consent of OMICRON electronics. Reprinting, wholly or in part, is not OMICRON electronics Corp. USA
permitted. 12 Greenway Plaza, Suite 1510
Houston, TX 77046, USA
The product information, specifications, and technical data embodied in this manual represent
the technical status at the time of writing and are subject to change without prior notice. Phone: +1 713 830-4660 or 1 800 OMICRON
We have done our best to ensure that the information given in this manual is useful, accurate E-Mail: [email protected]
and entirely reliable. However, OMICRON electronics does not assume responsibility for any Web: www.omicronusa.com
inaccuracies which may be present.
The user is responsible for every application that makes use of an OMICRON product. For addresses of OMICRON offices with customer service centers, regional sales offices or
OMICRON electronics translates this manual from the source language English into a number offices for training, consulting and commissioning, please see our website.
of other languages. Any translation of this manual is done for local requirements, and in the
event of a dispute between the English and a non-English version, the English version of this
manual shall govern.
Preface Introduction Quick Current Voltage Transformer Resistance Others Common Technical Data CP TD1 CP CU1 CP SB1 CP CB2
Transformer Transformer Functions
Preface
CPC 100 V 1.43
About this User Manual Safety Instructions for the CPC 100 and its Accessories
The purpose of this User Manual is to get you started quickly. It guides you directly to the various Orderly Measures
Caution: The CPC 100 must be used in observance of all existing safety require-
CPC 100 application fields, shows the typical test setup, the corresponding CPC 100 test card,
ments from national standards for accident prevention and environmental protec- • This User Manual only complements the CPC 100 Reference Manual available in PDF
and outlines the parameters used for this test in a compact form.
tion. format on the CPC 100 Toolsets and the CPC 100 Start Page. However, it does not replace
Since the scope of this User Manual is confined to the most important information about a it.
specific subject, the CPC 100 User Manual complements the CPC 100 Reference Manual, Before operating the CPC 100, read the following safety instructions carefully. It is not • Either this User Manual or the CPC 100 Reference Manual should always be available on
however, it does not replace it. The CPC 100 Reference Manual is available in PDF format on recommended that the CPC 100 be used (or even turned on) without understanding the the site where the CPC 100 is being used.
the CPC 100 Toolsets and the CPC 100 Start Page. information in this manual. If some points of the safety instructions are unclear, contact • Personnel assigned to use the CPC 100 should carefully read the CPC 100 User Manual/
OMICRON electronics. Reference Manual - in particular the section on safety instructions - before beginning to work
Reading the CPC 100 User Manual alone does not release the user from the duty of complying
with all national and international safety regulations relevant for working with the CPC 100, for with it. On principle, this also applies to personnel who only occasionally work with the
example, the regulation EN50191 "Erection and Operation of Electrical Test Equipment" as well Principle Use According to Regulations CPC 100.
as the applicable regulations for accident prevention in the country and at the site of operation. • The CPC 100 should only be used in a safe manner, mindful of the dangers while paying • Do not undertake any modifications, extensions, or adaptations to the CPC 100.
attention to the User Manual, and when it is in a technically sound condition and when its • Use the CPC 100 in conjunction with original accessories only.
Conventions and Symbols Used use is in accordance with the regulations. In particular, avoid disruptions that could in turn
affect safety. Operator Qualifications and Primary Responsibilities
In this manual, the following symbols indicate paragraphs with special safety relevant meaning:
• DANGER: If you have a cardiac pacemaker, do not use the CPC 100! Before operating the
Symbol Description CPC 100, make sure there is no person with a cardiac pacemaker in the immediate vicinity. Warning: Testing with the CPC 100 should only be performed by authorized and
• The CPC 100 is exclusively intended for the application fields specified in detail in qualified personnel. Clearly establish the responsibilities.
Equipment damage or loss of data possible.
”Designated Use” on page Preface-4. Any other use is deemed not to be according to the
regulations. The manufacturer/distributor is not liable for damage resulting from improper Personnel receiving training, instruction, direction, or education on the CPC 100 should remain
usage. The user alone assumes all responsibility and risk. under the constant supervision of an experienced operator while working with the equipment.
Personal injury or severe damage to objects possible. • Following the instructions provided in this User Manual and in the CPC 100 Reference
Manual available in PDF format on the CPC 100 Toolsets and the CPC 100 Start Page is Safe Operation
also considered part of being in accordance with the regulations. When putting the CPC 100 into operation, follow the instructions in section "Putting CPC 100
• Do not open the CPC 100 housing. into Operation" in the CPC 100 Reference Manual (available in PDF format on the
• If you do not use the CPC 100 anymore, turn the safety key to "lock" (vertical) and remove CPC 100 Toolsets or the CPC 100 Start Page).
the key to avoid anybody accidentally turning on the CPC 100.
• Store key and the CPC 100 separately to prevent unauthorized personnel from using the Note: Never use the CPC 100, any accessory or the CP TD1 equipment trolley without a solid
CPC 100. connection to earth with at least 6 mm². Use a ground point as close as possible to the test
object.
Preface - 1
CPC 100 V 1.43
Safety Instructions for the CPC 100 and its Accessories

General • All AC and DC output sockets of the CPC 100 can carry life-hazardous voltage potential and – Do not stand right next to or directly underneath a connection point because the clamps
• Before connecting or disconnecting test objects and/or cables, turn off the CPC 100 by provide life-hazardous currents. Therefore: may fall off and touch you.
either the POWER ON/OFF switch or the Emergency Stop button. Never connect or – While connecting cables to the CPC 100 high-voltage or current outputs, or other This is a physical and an electrical hazard.
disconnect a test object while the outputs are active. conducting parts that are not protected against accidental contact, press the Emergency – The red warning light on the CPC 100 front panel indicates hazardous voltage and/or
Stop button, and keep it pressed as long as an output signal is not absolutely necessary current levels at the CPC 100 outputs (red light "I" on or flashing). The green warning
Note: Even if you switched off the CPC 100, wait until the red I/O warning light is fully
for the test. light indicates that the CPC 100 outputs are not activated.
extinguished. As long as this warning light is lit, there is still voltage and/or current potential
on one or more of the outputs. – When connecting to the front panel input/output sockets, use wires with either 4 mm Note: If none or both warning lights are on, the unit is defective and must not be used
safety "banana" connectors and plastic housing or, where applicable, with the especially anymore.
• Make sure that a test object’s terminals that are to be connected to the CPC 100 do not carry manufactured counterpart supplied by OMICRON electronics (e.g., for the V2 AC
any voltage potential. During a test, the only power source for a test object may be the measuring input). – Both of the high-current output sockets on the left-hand side of the test set (400A DC
CPC 100. and 800A AC) usually carry a relatively low-voltage potential.
• At their output sockets and especially in the cables connected to them, in operation the high- – For the high-voltage and current output connectors on the left-hand side of the test set
current outputs 400A DC and 800A AC generate a significant amount of heat (approx. (2kV AC, 400A DC and 800A AC, Ext. Booster), only use the specially manufactured Warning: However, in case of an internal insulation fault these outputs may carry
300W/m at 800A). To prevent burns, use gloves when touching the cables while in cables supplied by OMICRON electronics (refer to the chapter "Accessories" of the up to 300 V. Consider these outputs life-hazardous!
operation or a short while after. CPC 100 Reference Manual available in PDF format on the CPC 100 Toolsets or the
• Do not insert objects (e.g., screwdrivers, etc.) into any input/output socket. CPC 100 Start Page). – Always lock connectors properly.
• Never use the test cards Quick and Resistance to measure the resistance of windings with – One end of the high-voltage cable has a coaxial safety plug that is certified for a voltage The counterpart of the high-current sockets are locking connectors.
a high inductance because turning off the DC source results in life-threatening voltage level of 2kV AC. The other end is equipped with a safety banana plug that is insulated
levels. For this kind of measurement only use either the special winding resistance test card with a shrink tube. To lock these connectors safely, insert them carefully until you feel a
RWinding or the test card TRTapCheck! "click" position. Now they are locked. Confirm this by trying to pull them
• When measuring the ratio of voltage and power transformers make sure that the test voltage Warning: When the CPC 100 is switched on, consider this part of the cable a out. This should not be possible now.
is connected to the corresponding high-voltage winding, and the voltage of the low-voltage hazard of electric shock! To remove the locking connectors, unlock them by pushing them in
winding is the one that is measured. Accidentally mixing up the windings can generate life- completely first, and then pull them out.
threatening voltages within the transformer. – If you do not use the high-current outputs 400A DC or 800A AC, or the high-voltage
• Make sure that when testing a current transformer by feeding a test current into its primary output 2kV AC, disconnect any cable that may be plugged in to these sockets.
winding, all secondary windings are shorted. On open secondary windings, life-threatening Note: The 400A DC or 800A AC outputs are not switched off by internal relays. Therefore,
voltages can be induced! if a test mode is selected that does not use either one of these two outputs, they still
• Use only one CPC 100 output at a time. generate current.
Preface - 2
Preface
CPC 100 V 1.43
Safety Instructions for the CPC 100 and its Accessories

• The high-current cables for both the 800A AC and 400A DC outputs are equipped with Power Supply DC Output to Test Objects with a High Inductance
connection clamps at one end. If these connection clamps are attached to a test object’s • Supply the CPC 100 only from a power outlet that has protective earth (PE).
terminal that is situated above your head, make sure the clamp is securely attached. Due to Use test cards RWinding (winding resistance) and TRTapCheck (tap changer winding
• An error message (313) appears if either the PE connection is defective or the power supply resistance and on-load tap changer interruption check) only:
the weight of the cables the clamp may become loose and fall down. has no galvanic connection to ground. In this case, make sure that the PE connection is
• Do not operate the CPC 100 under ambient conditions that exceed the temperature and intact. If the PE connection is intact and the error message still appears, select the "Disable Warning: As long as the CPC 100 software shows the on-screen message
humidity limits listed in ”General” on page Technical Data-3. ground check" check box at the Device Setup tab in the Options view. “Switch off in progress”, NEVER connect or disconnect test objects and/or cables.
• Do not operate the CPC 100 in the presence of explosives, gas or vapors. • Ground the isolating transformer outputs or generators used to supply the CPC 100 on the
• If the CPC 100 or any add-on device or accessory does not seem to function properly, do N (neutral) output or select the "Disable ground check" check box as described above.
not use it anymore. Please call the OMICRON electronics hotline (refer to cover page of this • Instead of supplying the CPC 100 from phase - neutral (L1-N, A-N), it may also be supplied The message "Switch off in progress" notifies you that, after
User Manual. from phase - phase (e.g., L1-L2; A-B). However, the voltage must not exceed 240V AC. the CPC 100 was switched off, the connected external
• Fuse-protect the power supply (16A slow-acting fuse). inductance (i.e., the test object) still "feeds" voltage potential
• Do not use an extension cable on a cable reel to prevent an overheating of the cord; run out back into the 6A DC or 400A DC output.
FOR YOUR OWN SAFETY the extension cord. The existence of this voltage potential at the 6A DC output is
Always follow the 5 safety rules: also indicated by a lit LED - even if the CPC 100 is switched
Caution: The connector “Ext. Booster” is always galvanically connected to
1. Insulate off.
mains, regardless whether or not an external booster is selected on the software
2. Secure to prevent reconnecting tab Options | Device Setup, the green warning light (0) is on, the outputs are If a test object with a big inductance is connected to the
turned off or the Emergency Stop button is pressed. CPC 100, ground the test object on both ends before
3. Check isolation
Handle with extreme caution. Do not use any other booster cables than the ones disconnecting it from the CPC 100.
4. Earth and short-circuit supplied by OMICRON electronics.
5. Cover or shield neighboring live parts
Warning: The CP SA1 discharge box must be connected to the CPC 100’s V DC
input sockets when using the 400A DC output to protect yourself and the
CPC 100 from high-voltage hazards.
If a test object with a big inductance was connected to the CPC 100, short-out the test object
additionally before disconnecting it from the CPC 100.
Warning: Use separate clamps for current and voltage connections on both sides
of the test object to avoid hazards in case one clamp falls off during the test.
Preface - 3
CPC 100 V 1.43
Designated Use
Changing Fuses CPC 100 in Combination with the CP TD1 The CPC 100, in conjunction with its accessories or as a stand-alone unit, is a multi-
• Turn off the CPC 100, unplug the power cord and/or press the Emergency Stop button. purpose primary test set for commissioning and maintaining substation equipment. It
The CP TD1 is an optionally available high-precision test system for on-site insulation tests of
• We recommend to wait for about 30 seconds. This time is necessary for the internal performs current transformer (CT), voltage transformer (VT) and power transformer (TR)
high-voltage systems like power and measuring transformers, circuit breakers, capacitors and
electrolytic capacitors to fully discharge. tests. Furthermore, it is used for contact and winding resistance testing, polarity checks as
isolators. The CP TD1 works as an add-on device to the CPC 100 and is described in chapter
• Ground the test object, and disconnect it from the CPC 100. By disconnecting it, you prevent ”CP TD1” of this User Manual. well as primary and secondary protection relay testing.
a possibly faulty test object feeding power back into the CPC 100.
On principle, the safety instructions that apply to the CPC 100 and its accessories also apply to The various, partly automated tests are defined and parameterized via the front panel control of
• Locate the blown fuse on the front panel of the CPC 100, and replace it.
the CP TD1. However, the CP TD1 requires some additional precautions and measures. They a built-in embedded PC.
Note: Replace with identical fuse type only (refer to the chapter "Changing Fuses" of the are listed in chapter ”CP TD1” on page CP TD1-1. The functionality scope of the CPC 100 is described in detail in the chapter "Designated Use" of
CPC 100 Reference Manual available in PDF format on the CPC 100 Toolsets or the CPC 100
the CPC 100 Reference Manual available in PDF format on the CPC 100 Toolset CD-ROM or
Start Page).
Different Symbols for PE the CPC 100 Start Page.
The CPC 100 and CP TD1 use different symbols for protective earth (PE): Note: Any other use of the CPC 100 but the one mentioned above is considered improper use,
and will not only invalidate all customer warranty claims but also exempt the manufacturer from
its liability to recourse.
This is due to a new standard and does not symbolize any functional difference.
Note: Both symbols mean exactly the same, i.e., protective earth (PE) or equipotential ground.
Preface - 4
Preface
Introduction
CPC 100 V 1.43
Functional Components of the CPC 100

I / 0 warning lights
indicate either a safe operation, i.e., no voltage at the CPC 100 outputs (green light "0" on), or an operation with possibly hazardous voltage and/or current levels at the CPC 100 outputs (red light "I" on or flashing).
Add test cards

Safety key lock
We recommend not to use more than 15 test cards or 50 test
Locks front panel operation.
results in one test procedure.
BIN IN
Binary trigger input, wet or dry contact Test Card View: View to set up test cards,
compose test procedures, enter test settings,
IAC/DC INPUT define test cards or the test procedure default, start
Fuse-protected with a 10A very quick-acting fuse tests etc.
Fuse 6.3A T (slow-acting wire fuse 5x20 mm) Test Procedure Overview: Provides an
for 3A AC, 6A AC, 130V AC and 6A DC enhanced overview of all test cards of the currently
active test procedure. Defines the test procedure
AC OUTPUT default.
6A, 3A or 130V output
File Operations: Lets you save, load, delete, copy
Fuse 3.15A (slow-acting wire fuse 5x20 mm) and rename test procedures.
for 3A AC and 130V AC Options: To specify general parameters.
V1 AC input V2 AC input
300V AC input 3V AC input Context-dependent menu keys
Directly invoke specific commands associated with the
DC OUTPUT currently selected control of the test card and view.
6A DC output (fuse-protected with a 6A fuse)
VDC INPUT I/O

10V DC input or 2-wire resistance Use to start and stop a test.
Emergency stop button Tab selector
Immediately shuts off all outputs (could leave transformer in Soft-touch Navigation To change between the single test cards of a test procedure.
saturation). keyboard elements
Introduction - 1
CPC 100 V 1.43
Functional Components of the CPC 100

High-Voltage and Current Outputs 1. For detailed information on the RJ45 connectors, see chapter "CPC 100 in a Network" in the
Warning: The connector "Ext. Booster" is always galvanically connected to
CPC 100 Reference Manual available in PDF format on the CPC 100 Toolsets or CPC 100
When the CPC 100 outputs high current, observe the allowed duty cycles that may apply to the mains, regardless whether or not an external booster is selected on the
Start Page.
selected AC output range. software tab Options | Device Setup, the green warning light (0) is on,
the outputs are turned off or the Emergency Stop button is pressed. 2. For the pin assignment of the RS232 serial interface plug, refer to the CPC 100 Reference
Grounding 400A DC Use only original accessories available from OMICRON electronics. Manual, section "ePC Interfaces" of chapter "Technical Data".
terminal (4-4.5V DC) 3. The connector for external safety functions allows connecting:
High DC current ePC Interfaces1 – an external Emergency Stop button
– an external "test start/stop" push-button
– external I/O warning lights
USB connector for connecting OMICRON – CP CR500
electronics USB memory sticks
800A AC The attached plug contains a jumper for the emergency stop or "dead man" function, and as long
2kV AC
(6.1-6.5V AC) as the plug is placed on the connector, these functions are bridged. If the plug is removed,
High-voltage emergency stop is active.
output High AC current RJ45 socket for connecting CPC 100 to a PC
output or a network hub For the plug’s pin assignment and a wiring scheme, refer to section "Connector for External
Green LED
Safety Functions" of chapter "Technical Data" in the CPC 100 Reference Manual available in
Ext. Booster PDF format on the CPC 100 Toolsets or CPC 100 Start Page.
e.g., for the Red LED
connection of the Reference point Serial interface connector for connecting
CP CB2 current optional CP TD1 test set
booster option for
output currents of Connector for external safety functions (see
up to 2000A item 3 below)
Mains power supply, Automatic circuit POWER ON /OFF

1 phase, 85V-264V AC breaker I > 16A switch
1. Older CPC 100 versions have slightly different ePC interfaces. For detailed information refer to
the CPC 100 Reference Manual.
Introduction - 2
Introduction
CPC 100 V 1.43
CPC 100 Block Diagram Principles of Test Cards and Test Procedures The Components of a Test Card
Ext. Test Cards Focus on the data entry field for AC current.
Booster
The CPC 100 software comprises a number of test cards. A test card carries out one specific The term "focus" designates the currently selected (active) part of the test card. The selected
Rectifier
& power test, e.g., measuring a CT excitation curve, or testing the ratio of a voltage transformer. component is highlighted or inverted.
factor +
corrector
500V A test card holds a number of user-definable test settings and - after the test was run - test The actual function of the context-dependent
R
500V results. menu keys depends on the selected view, test
2kV mode, test card and selected test card
500V 500V 4A
Switched 1kV 2A
R
Test Procedure component (i.e., the focus).
2kV 1A
mode 500V
amplifier A test procedure contains multiple test cards.
Temperature and power consumption
L
Mains The composition of such a test procedure and the settings of all single test cards can be freely monitoring.
100-240V Filter defined by the user. Within a test procedure, each test card and its associated test is executed If an output is activated, both the CPC 100’s
50/60Hz I individually in a user-defined order. power consumption and the current emitted at
65V 130V / 6A AC
N 2kV
U O the high-current outputs is monitored and,
65V
PE I 800A u Report together with the temperature, displayed by this
3.15A t temperature gauge.
ADC U
p For archiving or reporting purposes, or later processing, a test procedure with all of its test cards, Status of test assessment. The test
6.3A The temperature gauge’s bar therewith
U 65V / 6A DC
u specific settings and - after the test was run - test results and assessments can be saved. It is assessment is a manual procedure carried represents an indicator for the remaining time
DSP I t then considered a report. out by the user. After the test, set the focus
(Digital the CPC 100 can output power.
Signal
U
s Such a report can later be opened any time in the CPC 100’s File Operations menu. on the assessment symbol. Use the context-
Processor)
dependent menu key OK or Failed to assess plenty of spare
6V / 800A AC Note: For detailed information about test cards, test procedures and templates, refer to section
the test. no more spare
"How to Use The CPC 100 Software" of chapter "Introduction" in the CPC 100 Reference
For a few seconds, the status line also
Manual available in PDF format on the CPC 100 Toolsets or CPC 100 Start Page.
+ displays general operation information, e.g.
Ethernet
5V / 400A DC "Emergency key pressed".
-
to 300V AC
RS 232 Built-in
ext.
ePC 3V AC I Pressing the Settings menu key opens the Settings page (see page Quick-1) allowing you to
PC optional 10A AC/DC
n
10V DC set the test cards individually. As a rule, do not set the test cards on the Settings page but set
BIN IN p.
all test cards of a test procedure using the Device Setup tab in the Options view (see page
optional analog or digital interfaces Introduction-5).
(plug-in boards)
Introduction - 3
CPC 100 V 1.43
Test Procedure Overview The CPC 100 File System

The highest hierarchical level of the CPC 100 file system, the "root", is named CPC 100. Below Note: The file containing the up-to-date measurements should be saved regularly. If the test unit
this, you can create additional folders in a tree-structure of your choice, save tests in these is switched off, or in case of a power outage, all unsaved measurements will be lost.
folders, and perform file operations, such as open, save, rename, copy, paste etc.
Navigating Through the File System
Select a test or a folder using the handwheel or the Up / Down keys. To expand a collapsed
folder tree , select it and press either the handwheel or Enter.
The Menus
Main File Operations Menu
Opens the submenu File (refer to “Submenu File” on page 5)
The Test Procedure Overview lists all test cards of the currently active test procedure in a list
Opens the submenu Edit (refer to “Submenu Edit” on page 5)
box showing the card’s name, its creation date and time, whether test results are available and
the test card’s assessment status.
The CPC 100 file system differentiates two file types: Saves the currently open test, i.e., the test card(s) previously opened in the Test
Card View (refer to Note below).
With Save As Default, Test Procedure Overview provides a function to save the
current test procedure as the test procedure default, i.e., that default the CPC 100 name.xml A test procedure with all of its test cards and specific settings. An .xml file Opens the String Editor. You can save the currently open test under a new name
software will start with in future. may also contain test results and assessments that were stored together of your choice (15 characters max.).
with the settings as report in the CPC 100 file system for archiving
Note: For detailed information refer to section "Test Procedure Overview" of chapter purposes. Use the handwheel or the Up / Down keys to select a test, and press Open to open
"Introduction" in the CPC 100 Reference Manual available in PDF format on the it. Changes to Test Card View.
name.xmt Test procedure template, i.e., a user-defined template containing one or
CPC 100 Toolsets or CPC 100 Start Page.
more test cards with all of their specific test settings but without test Closes the current test card(s), changes to Test Card View and opens the test
results. procedure default.
Introduction - 4
Introduction
CPC 100 V 1.43
The CPC 100 File System The Options Menu

Note: Unlike the other menu items, the two Save…functions of the main File Operations menu Submenu Edit Device Setup
directly effect the currently open test, i.e., the test procedure that was composed in the Test
Set the external booster you
Card View, or the test that was loaded in the CPC 100 file system beforehand.
Select the test of your choice. Press Cut to put the selected test or folder to the want to use (CB2, CU20 or
Therefore, pressing Save, for example, does not save the test that you may have highlighted in
Clipboard. Proceed with Paste… CU1).
the folder tree, but the one that is currently open. Set current clamp
Select the test of your choice. Press Copy to copy test or folder to the CPC 100 parameters and CT and/or
Submenu File clipboard. Proceed with Paste… VT transformation ratio.
Move to the destination folder of your choice. Press Paste to insert the contents of Select the check box if the
Opens the String Editor. You can create a new folder with any name of your choice.
the CPC 100 clipboard to this folder. PE connection is intact and
an error message (313)
Appends the contents of a test file (.xml) or template (.xmt) of your choice to the Press Paste As Templ. to make the contents of the CPC 100 clipboard a test
appears.
currently open test. procedure template.
Operating the CPC 100
(for future use) with the check box
Deletes the currently selected test or folder from the CPC 100’s disk space. selected can cause injury
or possibly death of the
Closes the Edit submenu and returns to the main File Operations menu. operating staff! Resets all user-specific settings made in the
Opens the String Editor that enables you to rename the current test to any new CPC 100 software to factory-defined defaults
name of your choice. including:
Set the default frequency.
(for future use) Note: If a folder is cut or copied to the Clipboard, the selection is recursive, i.e., all of its This value will be used for all • the test card defaults
subfolders will also be put to the Clipboard. test cards. • the test procedure default
Cutting or copying a test or folder, and trying to paste it in the same location, opens the String • all settings made at the Device Setup tab
Closes the submenu and returns to the main File Operations menu. (Sets external booster to CB2, sets CT and
Editor. Auto save automatically
Since a test or folder cannot exist twice under the same name at the same location, determine saves the current test VT to "OFF" and sets the default frequency
a new name for it using the String Editor. settings in fixed intervals to 50 Hz.)
specified to a file named • the String Editor’s template strings
lastmeas.xml.
Introduction - 5
CPC 100 V 1.43
The Options Menu

Network Date / Time Regional Settings
Setting the communication parameters. Set date and time. Regional setting for language, temperature unit, date and time style. These settings affect the
way the CPC 100 software displays and sort dates, times, numbers and decimal points.
DHCP / Auto-IP
Configures all communication
parameters automatically; the DHCP Define system language
server will do it for you or it will be done Set system date.
via the Auto-IP mechanism. Define temperature unit °C or °F
The data entry fields for IP address, To set the system time:
Subnet Mask, Default Gateway and Define the display style for date and
DNS are read-only, no data can be • put the focus onto the Time: time
entered. This is the recommended field using the handwheel
setting.
• use the Up/Down keys to
Static IP select between hours,
Configure the communication minutes and seconds
parameters manually by entering the • turn the handwheel to
values into the data entry fields using the increase or decrease the
soft-touch keys. value
• press the handwheel to
Display
acknowledge your entry.
Sliding regulator to adjust the display
contrast.
Introduction - 6
Introduction
CPC 100 V 1.43
The Options Menu Customizing Your Working Environment Accelerator Keys

Service 1st Goal: Always Loading Certain Test Cards on System Start-Up With the exception of Quick, pressing an accelerator key opens the corresponding Insert a new
test card dialog box and lets you select the test card of your choice. Pressing Quick opens the
During operation, the CPC 100 creates a log file with a user-definable logging level. Quick test card directly.
Fill out one or more test card(s) of your choice with the parameters you need.
Change to Test Procedure Overview. Quick test card

We recommend to set the logging
level to Warning.
Select from current transformer (CT) test cards
Press Save As Default
You have now set the default for the CPC 100 start-up.
Select from voltage transformer (VT) test cards

System Info
2nd Goal: Loading a Certain Test Card with Always the Same Values
Displays system information.
Select from power transformer test cards
Fill out the test card of your choice with the parameters you want to assign to that
card.
Select from resistance test cards
Put the focus to the test card’s tab.
Select from other test applications

Press Save As Default
You have now changed the default for this test card type.
The command Restore Defaults at the Options tab Device Setup resets all
user-specific settings made in the CPC 100 software to factory-defined defaults.
This includes the test card defaults and the test procedure default.
Introduction - 7
CPC 100 V 1.43
Introduction - 8
Introduction
Quick
CPC 100 V 1.43
Settings Page Measuring with Quick

Quick is the most basic mode to operate all of the CPC 100 outputs in a manual-like mode with If the output quantities of the selected output can be measured, the combo boxes “1st measured
Pressing the Settings menu key opens the Settings page. The Settings page
front panel control. quantity” and "2nd measured quantity" provide I Out and / or V Out for selection.
with the exception of the TRRatio test card looks as shown below.
I Out sel and V Out sel designate the frequency-selective measurement to filter out
Set output range Set output value Overload indication interferences as they usually occur in substations. The measured input is filtered according to
No indication: the set output frequency.
no overload
Set frequency value
or - if Sync w/ Dotted indication: After having set all necessary parameters, press the I/O (test start/stop) push
V1 AC is selected - an overload in the button. The Quick test card enters the "on" state, the set power output value is
phase angle. past switched to the CPC 100’s outputs, the measuring continues.
Solid indication: Pressing the Quick test card menu key Keep Results saves the currently
1st measured an overload now measured values and "freezes" their display in the measurement table. Both the
quantity (including Set the calculated "measuring" and the "on" state remain active, the measurement continues in a
CT and VT) value to be new line of the measurement table.
displayed in table
2nd measured below.
quantity (including Depends on Caution: When testing capacitive test objects using voltages ≥ 500 V, make sure
CT and VT) settings 1st and 2nd that the test object’s capacity does not exceed 25 nF.
measured quantity. Together with the test object’s capacity, the leakage inductance of the CPC 100’s
The Settings page allows setting the test cards individually. At the Device Setup tab in the internal output transformer forms a series resonant circuit. Especially at
Measurement table showing results Options view (see page Introduction-5), the same properties can be set for all test cards of a frequencies > 50 / 60 Hz this may result in voltage superelevation.
test procedure. As a rule, do not use the Settings page but the Device Setup tab in the Options
view to set the test cards. Making different settings for the test cards is rarely a good idea. Set
Range the test cards individually using the Settings page only in well-founded cases. Caution: Never use Quick to measure the resistance of windings with a high
inductance because turning off the DC source results in life-threatening voltage
The output range combo box provides a list of available output ranges including either CB2:, If a test card contains results, the settings cannot be changed. When a file containing results is levels.
CU20: or CU1: output ranges if the respective external booster was selected at the Options tab loaded, the Settings page can be used to view the settings of the test procedure. For this kind of measurement only use the special winding resistance test card
Device Setup or on the Settings page. RWinding or the test card TRTapCheck.
Quick - 1
CPC 100 V 1.43
Synchronizing Output Frequency with V1 AC Trigger Settings

Sync w/ V1 AC A trigger is the occurrence of a selected event, for example, a binary trigger is the first change
of the state at the binary input.
Select the trigger event Threshold value for trigger
Set Sync w/ V1 AC by pressing the menu key that appears when the focus is on on measurements.
the frequency / phase angle data entry field.
This synchronizes the CPC 100 output frequency with the V1 AC input frequency Indicates the signal
(we recommend a minimum input voltage of 10 V on V1 AC, possible range 48 - condition at the binary
62 Hz). In this case the phase angle of the output is displayed rather than the input Bin In.
frequency. Set the phase angle value relative to the phase angle of the V1 AC
input signal.
Delay time display Select to switch off the CPC 100 outputs
The icon next to the frequency / phase angle data entry field reflects the actual
when the trigger event occurs.
setting. The delay time is the time between the last
change of the CPC 100 output value and the Clear to leave the CPC 100 outputs on after
Due to the PLL (phase locked loop) technology, the synchronization with V1 AC
occurrence of the trigger event. the trigger event occurred.
takes places about 100 ms after the test was started.
The measurement values are "frozen".
Note: Sync w/ V1 AC is not available in all output modes. To store the results, press .
Note that some of the trigger events offered in the Trigger on: combo box depend on the
measured quantity settings below (trigger on measurement).
Trigger on "Overload": the occurrence or the clearing of an output overload condition (clearing
is delayed by 100 ms to debounce).
Quick - 2
Quick
Current Transformer
CPC 100 V 1.43
CTRatio (and Burden) CTRatio (with Burden) - The Option Measure Burden
Use the CTRatio test card to measure a current transformer’s ratio and burden with injection on Select the check box Measure Burden to measure the burden in VA.
the CT’s primary side with up to 800 A from AC OUTPUT. Nominal primary current
Note: This option is only useful as long as the injected current I test is about of the magnitude
Primary Output range Select to stop test automatically when measurement is of the nominal current I prim.
injection current done.
Nominal secondary current
Use current clamp
Actual current rather than IAC
injected into CT’s input*)
primary side
Burden
CT
Burden
CT
Phase angle 
relative to Iprim
Measured Select to enter

secondary secondary current
current instead of
measuring it
Ratio Iprim. / Isec.: Polarity: See “CTRatio (with

Isec act x (Iprim nom/Iprim act) OK = phase I sec - phase I prim Burden) - The Option
and deviation in % = - 45 ° < 0 ° < + 45 ° Measure Burden” on
((Kn x Isec - Iprim)/Iprim) x 100% page Current
NOTOK = all other cases
Transformer-2
*) Due to cross-talk between the measuring inputs V1 AC and V2 AC, we suggest not to connect
a current clamp to the input V2 AC. Therefore, use a current clamp with current output. See also
“Device Setup” on page Introduction-5.
Current Transformer - 1
CPC 100 V 1.43
CTRatio (with Burden) - The Option Measure Burden CTBurden

Additional measurements when Measure Burden is selected: This is the preferred method in cases, when the current of max. 800 A that the CPC 100 can
feed into the CT’s primary side is not sufficient.
Secondary Nominal secondary
injection current current
from 6A AC
output Select to stop test automatically when
V sec: measured secondary voltage measurement is done.
and phase angle relative to Iprim
Burden
Output frequency
CT
Actual injection
Burden in VA: I sec nom × current
(V sec act × I sec nom/I sec act) measured via Select to enter
input I AC secondary voltage
cos : cosine of angle between I sec and V sec instead of
measuring it
Secondary
voltage at the
Note: For the meaning of the other test card components, refer to page Current Transformer-1.
burden,
measured at
Cosinus of phase
input V1 AC,
angle 
and phase angle Burden in VA: I sec nom ×
 relative to Isec (V sec act × I sec nom/I sec act)
Current
Transformer
CPC 100 V 1.43
CTExcitation (Knee point)

Use the CTExcitation test card to record the excitation curve of a current transformer. This test Maximum test voltage The graph displays the test results in form of an interpolated curve with test point markers.
performs an automatic injection of a test voltage of up to 2 kV to the current transformer’s Turn the handwheel to set the focus onto the graph, and press it. This will bring up a crosshair
Maximum test
secondary side. cursor that lets you navigate through the list of test points by using the keys Previous Point and
current
Next Point. Turning the handwheel has the same effect. The fields V: and I: display the value
Select to run test pair of each test point.
Output
frequency automatically.
Note: Pressing
Demagnetizing the CT Core
Add Point to add Performing a CT Excitation measurement demagnetizes the CT core.
Actual voltage a test point to the
Burden
CT graph does not Demagnetization can also be done without recording an excitation curve by
work in Auto pressing the button Demag.
Actual current mode.
To make the context-dependent menu key Demag. visible put the focus onto the test card’s tab.
IEC/BS According to IEC 60044-1, the knee point is defined as the point on the
curve where a voltage increment of 10% increases the current by 50%.
ANSI 45° According to IEEE C57.13, the knee point is the point where, with a double
logarithmic representation, the tangent line to the curve forms a 45° angle.
Applies to current transformer cores without an air gap.
ANSI 30° Like ANSI 45° but forming a 30° angle.
Applies to current transformer cores with an air gap.
CPC 100 V 1.43
Winding Resistance Voltage Withstand Test

Use the test card RWinding to measure the resistance of a current transformer’s secondary Nominal test Output range Measurement range Maximum Use the test card VWithstand to measure the voltage withstand capability of the secondary
winding. current deviation between winding and secondary wiring. To do so, disconnect the burden. As shown in the following
the measured figure, connect one cable of the 2 kV output to the transformer’s secondary (1S1) winding
Warning: Never open the measuring circuit while current flows. Dangerous volt-
values within the connection and the other cable to earth and the transformer’s primary connection (P1). Open
age may occur! Check whether the red warning light "I" and the discharge LED Actual test
last 10 s of the the secondary ground connection and ground the burden for safety reasons.
are off before disconnecting the device under test. Before disconnecting from the current
CPC 100, connect the device under test on both ends to protective earth. measurement. The
results are
considered stable
Measured if Dev < 0.1%.
voltage at input
V DC
Burden
CT
Burden
CT
Transformer’s
winding
Total elapsed time
resistance
Enable/disable
temperature T meas: Actual ambient temperature
compensation
Off before disconnecting for the result T ref: Temperature for which the result is calculated
device under test R ref: Calculated resistance.
In Centigrade:
Rref = (V DC / I DC) x (235° C + T ref) / (235° C + T meas)
In Fahrenheit:
Rref = (VDC / IDC) x (391°F + Tref F) / (391°F + Tmeas F)
Note: Formula according to IEC 60076-1
Off before disconnecting device under test Note: If n/a appears in the V DC or R meas box, the V DC input is overloaded.
Current
Transformer
CPC 100 V 1.43
Voltage Withstand Test Polarity Check

Use the PolCheck test card to check a series of test points for correct polarity.
Warning: Be aware that the terminal that is connected to the transformer’s sec-  If the CPOL detects the same signal characteristic at a test point, it considers the
ondary connection "1S1" leads life-hazardous voltage! To do so, the CPC 100 injects a special polarity test signal at a certain location. This signal can polarity as OK, and lights up the green LED.
either be a voltage or a current signal from the CPC 100, and has a signal characteristic similar
 If the signal characteristic is inverted or distorted, the CPOL considers the polarity
to a saw-tooth signal with a different steepness for the rising and the falling slope.
Terminates test when current Nominal test Output not OK, and lights up the red LED.
The polarity check itself is then done with the CPOL accessory, a portable easy-to-use polarity
threshold is reached voltage (2kV max.) frequency + If the CPOL detects a signal that is too low, both LEDs light up at the same time.
checker.
Remedy: increase the signal magnitude.
+ If the capacity of the CPOL’s battery gets low, the LEDs start flashing. As long as
Terminates test when testing
the LEDs are flashing, the CPOL’s battery provides sufficient power to continue
time has elapsed flashing working. However, the battery should be changed as soon as possible.
Warning: If you detect a wrong polarity in the current path, turn off the CPC 100
Actual test voltage first, and only then disconnect the terminals.
Actual test current green LED red LED Never operate the CPOL with an open battery compartment. A life-hazardous
The CPC 100 injects a
voltage level may occur in the battery compartment if the CPOL’s probe touches a
special polarity check  
signal test point with high-voltage potential!
Highest measured current
polarity polarity checker
checker CPOL CPOL
Time span Vtest is applied to
the output
During the test, the test voltage increases in a ramp characteristic from 0 V to V test. V test is
then applied to the output for the specified time span. The measurements are continuously
taken. Afterwards, V test decreases in a ramp characteristic.
CPC 100 V 1.43
Polarity Check CTRatioV (with Voltage)

Select the option Intermittent to Use the CTRatioV test card to measure a current transformer’s ratio. To do so, feed a voltage
1. save power in the 800A AC output range of up to 500 V from the 2kV AC output to the transformer’s secondary side.
2. define a pulse duty cycle for the output signal: The preferred method for CT ratio measurement is current injection using the CTRatio test card.
However, on some GIS CTs or bushing CTs on power transformers where the primary current
path is not accessible, the method described in this section is the only solution.
T on: time span the signal is applied to the output To measure the CT ratio using the CTRatioV test card, connect the 2kV AC output to the CT’s
T off: time span the signal output is paused secondary winding and the V2 AC input to the main conductors, e.g. on a power transformer to
the transformer’s bushings of different phases.
Burden
CT
A T on / T off ratio of 2.000 s / 9.000 s means the signal is applied for 2

seconds, then paused for 9 seconds. After that the cycle repeats.
Select output
range
Amplitude
Enter results
manually
Current
Transformer
CPC 100 V 1.43
CTRatio (with Voltage) CTRogowski

Secondary Nominal primary current Use the CTRogowski test card to measure a Rogowski coil’s ratio by injecting current into the
inception voltage current-carrying conductor, and by measuring the induced voltage at the end of the Rogowski
Nominal secondary current
coil windings.
Shielded cable with twisted wires.
Select to stop test A Rogowski coil’s induced voltage is proportional to the conductor current differentiated with
Shield connected to Rogowski Electronic protection relay
automatically respect to time. Therefore, in order to acquire a direct equivalent of the conductor’s current, the
Output coil. with integrator (e.g., 150 mV
when induced voltage needs to be integrated. In general, a Rogowski coil’s output signal is either lead
frequency at I nominal)
measurement is via an integrating amplifier or fed into an electronic protection relay with integrator. The
done CTRogowski test card integrates the Rogowski coil’s output signal at the CPC 100’s V2 AC
Measured input.
secondary
Disconnect the Rogowski coil’s output signal from the electronic protection relay, and plug it into
voltage
the CPC 100’s V2 AC input.
The CTRogowski test card measures the amplitude of the injected current I prim and the
Select to enter Rogowski coil’s output voltage V sec, integrates this signal, and calculates the secondary Relay
primary voltage current I sec, its phase angle as well as the actual ratio and the deviation.
Primary voltage
instead of
measured on
measuring it
V2 AC input
Ratio error
Polarity: Ratio Iprim. / Isec.:
Isec act x (Iprim nom/Iprim act)
OK = phase I sec - phase I prim
= - 45 ° < 0 ° < + 45 ° and deviation in %
((Kn x Isec - Iprim)/Iprim) x 100%
Note: If the transformer’s knee point voltage is approximated or exceeded, due to the
transformer’s saturation the measurement results are not correct anymore. If the knee point is
extensively exceeded, the transformer can even be damaged.
Therefore, the knee point voltage should be known or measured beforehand.
CPC 100 V 1.43
CTRogowski CTLowPower (Ratio)

Use the CTLow Power test card to measure the ratio of a low-power current transformer with a
Nominal secondary voltage of Rogowski coil Nominal frequency built-in burden and an output voltage that is directly proportional to the primary current.
of the Rogowski
Nominal primary Select check box for Nominal primary Nominal secondary voltage Select to stop test
Output range coil’s secondary
current of automatic test, clear for current automatically when
voltage
Rogowski coil manual test measurement is done
Electronic protection relay with low-voltage Output range
input (e.g., 22.5 mV at I nominal) Primary
injection
Primary injection
current
current
Built-in burden
Actual current
Frequency of injected into
Relay
injected current CT CT’s primary Phase angle 
I test side relative to Iprim
Shielded cable with
Actual output twisted wires
current
Select to manually Measured Select to enter
enter V sec secondary secondary voltage
instead of voltage instead of
measuring it measuring it
Secondary
voltage Ratio: Iprim / Isec and deviation of current ratio in %
Polarity: Ratio Iprim. / Isec.: Polarity:
Isec act x (Iprim nom/Iprim act)
OK = phase I sec - phase I prim OK = phase I sec - phase I prim
Calculated and deviation in % = - 45 ° < 0 ° < + 45 °
= - 45 ° < 0 ° < + 45 °
secondary ((Kn x Isec - Iprim)/Iprim) x 100%
current *) NOTOK = all other cases
*) Note that the current I sec does not really exist in the system. It is a calculated current only.
Current
Transformer
Voltage Transformer
CPC 100 V 1.43
VTRatio VTBurden
Use the VTRatio test card to measure a voltage transformer’s ratio with injection on the VT’s Use the VTBurden test card to measure a voltage transformer’s secondary burden with voltage
primary side with up to 2 kV from AC OUTPUT. Correction factor Nominal primary voltage injection on the VT’s secondary side with up to 130 V from AC OUTPUT.
for V prim 1/3 and 1/3: Correction factors for V sec To do so, open the circuit as shown in the figure below, and inject the AC voltage from the
CPC 100’s 130V AC output into the burden. Input I AC measures the current that flows into the
Nominal secondary voltage burden, and input V1 AC the voltage at the burden.
A Primary
a injection A
voltage a
Select to stop test
Output automatically
when
Burden
VT frequency
Burden
measurement is VT
done
Measured
n primary voltage
N Select to enter n
secondary voltage N
instead of
Secondary measuring it
voltage
measured at
V1 AC, and its
phase angle Ratio and deviation in %
relative to the
measured Vprim Polarity:
= - 45 ° < 0 ° < + 45 °
Voltage Transformer - 1
CPC 100 V 1.43
VTBurden Voltage Withstand Test Polarity Check

Correction factor for Vsec This test is identical to the voltage withstand test described on page Current Transformer-4. This test is identical to the polarity check described on page Current Transformer-5.
Output Nominal secondary voltage

frequency
Select to stop test automatically when measurement is A
a
done
Secondary
injection voltage
from 130V AC
output
Burden
VT
Use current clamp

rather than input
I AC*) n
N
Actual voltage at
the burden red LED
Select to enter green LED
measured at
input V1 AC
secondary current The CPC 100 injects a  
instead of special polarity check polarity checker
measuring it signal polarity
Actual current CPOL
checker CPOL
through burden
measured via Cosinus of phase angle 
input I AC and
its deviation
Burden in VA: Vsec nom × (Isec act × Vsec nom/Vsec act)
*) Due to cross-talk between the measuring inputs V1 AC and V2 AC, we suggest not to connect
a current clamp to the input V2 AC. Therefore, use a current clamp with current output.
Voltage
Transformer
CPC 100 V 1.43
VTElectronics TanDelta
Use the VTElectronics test card to test the ratio of non-conventional electronic voltage The TanDelta test card was especially developed for the CP TD1.
transformers with a very low-level secondary voltage. Correction factor The CP TD1 is an optionally available high-precision test system for on-site insulation tests of
Nominal primary voltage
for V prim high-voltage systems like power and measuring transformers, circuit breakers, capacitors and
Electronic protection relay
1/3 and 1/3: Correction factors for V sec isolators. The CP TD1 works as an add-on device to the CPC 100 and is described in chapter
Electronic voltage transformer with low-voltage input Primary ”CP TD1” of this User Manual.
injection Nominal secondary voltage
Since the TanDelta test card exclusively belongs to the CP TD1, it is also described in the
voltage
Select to stop test CP TD1 Reference Manual.
automatically
The TanDelta test card can be accessed from CT, VT, Transformer and Others test card
Output when
groups.
frequency measurement is
Shielded cable with done
twisted wires
Measured
primary voltage Select to enter
secondary voltage
instead of
Secondary measuring it
voltage
measured at
V1 AC, and its
phase angle
relative to the
Ratio and deviation in %
measured Vprim
Polarity:
= - 45 ° < 0 ° < + 45 °
CPC 100 V 1.43
Voltage
Transformer
Transformer
CPC 100 V 1.43
TRRatio (per Tap) Settings Page

Use the TRRatio test card to measure a power transformer’s ratio by injecting AC voltage with
Nominal primary injection voltage Pressing the Settings menu key opens the Settings page. The Settings page of
up to 2 kV from AC OUTPUT into the transformer’s primary side (refer to the following figure). Output
the TRRatio test card has another functionality as on other test cards.
Setup for testing a power transformer ratio: Yy0 transformer, primary and secondary side star frequency
connection. Primary
Nominal ratio, calculated from Vprim nom /
current from Note: The Settings page opens automatically if the Auto-tap operation mode is activated.
Vsec nom
2kV AC
output; Vector group; The Settings page allows adding the transformer’s ratio per tap as follows. After pressing the
changes selection Add Tap menu key first enter the Tap Number, V prim and V sec. Add the next tap by pressing
depending on depending on the the Add Tap menu key and enter the orresponding V prim and V sec values. After then,
the line settings pressing the Add Tap menu key repeatedly adds more taps with a step calculated from the
selected in values of the preceeding taps. The tap entries apply equally to all phases. After adding all taps,
table below press the Main Page menu key to transfer the data to the main page.
Operation mode Performing a TRRatio Test (per Tap)

Actual voltage
injected from
AC OUTPUT While passing through the power transformer’s tap changer positions, press
into the Keep Result for each single position.
transformer’s Note: This procedure is only required for manual wiring. Otherwise, the test runs
high-voltage side fully automatically.
Transformer tap
identifier and tap V sec Actual voltage measured at V1 AC
number for the ° Phase angle of the primary current relative to Vprim
measurements nominal.
in the respective
line of the table :1 Calculated ratio value from the measured values
Vprim / Vsec
% Deviation of the actual ratio from the nominal ratio
Transformer - 1
CPC 100 V 1.43
Settings Page TRRatio (per Tap)

The following table shows the V prim and V sec settings on the TRRatio test card for different
Dy5 V/H2 u/X1 A U-(V+W) / H1- w-u / X3-X1 √3/2
transformer’s winding connections. w/X3 (H2+H3)
Time needed to switch from one tap to Measurement starts at the lowest or highest
the next position Note: The table is valid for manual wiring and in connection with the CP SB1.
In the Transformer high-voltage side column, + means that the terminals in the CP SB1 are U/H1 W/H3 v/X2
short circuited. B V-(U+W) / H2- u-v / X1-X2
(H1+H3)
IEC Winding connection Mea- Transformer Transformer Mea- C W-(U+V) / H3- v-w / X2-X3
60076 sure- high-voltage side low-voltage side sured (H1+H2)
vector ment turn ratio
group Yd5 V/H2 u/X1 A U-(V+W) / H1- w-u / X3-X1 √3/2
w/X3 (H2+H3)
HV / H LV /X
Dd0 V/H2 v/X2 A U-V / H1-H2 u-v / X1-X2 1 U/H1 W/H3 v/X2
B V-(U+W) / H2- u-v / X1-X2
(H1+H3)
Select for U/H1 W/H3 u/X1 w/X3
C W-(U+V) / H3- v-w / X2-X3
the fully B V-W / H2-H3 v-w / X2-X3 (H1+H2)
automatic Yz5 u/X1 A U-(V+W) / H1- w-u / X3-X1 √3/2
C W-U / H3-H1 w-u / X3-X1 V/H2
and w/X3 (H2+H3)
Yy0 V/H2 v/X2 A U-V / H1-H2 u-v / X1-X2 1
extended
manual U/H1 W/H3 v/X2
mode U/H1 W/H3 u/X1 w/X3 B V-(U+W) / H2- u-v / X1-X2
(H1+H3)
B V-W / H2-H3 v-w / X2-X3
C W-(U+V) / H3- v-w / X2-X3
C W-U / H3-H1 w-u / X3-X1 (H1+H2)
Dz0 V/H2 v/X2 A U-V / H1-H2 u-v / X1-X2 1 Dd6 V/H2 w/X3 u/X1 A U-V / H1-H2 v-u / X2-X1 1
U/H1 W/H3 u/X1 w/X3 U/H1 W/H3 v/X2

B V-W / H2-H3 v-w / X2-X3 B V-W / H2-H3 w-v / X3-X2
C W-U / H3-H1 w-u / X3-X1 C W-U / H3-H1 u-w / X1-X3
Transformer - 2
Transformer
CPC 100 V 1.43
TRRatio (per Tap) Winding Resistance

Yz11 V/H2 v/X2 A U-(V+W) / H1- u-w / X1-X3 1*√3/2 Use the RWinding test card to measure the resistance of a power transformer’s winding as
Yy6 V/H2 w/X3 u/X1 A U-V / H1-H2 v-u / X2-X1 1
(H2+H3) described on page Current Transformer-4.
w/X3
Alternatively, inject the current directly from the 400A DC output as shown below.
U/H1 W/H3 v/X2 U/H1 W/H3 u/X1
B V-W / H2-H3 w-v / X3-X2 B V-(U+W) / H2- v-u / X2-X1 Warning: Connect the CP SA1 discharge box to the CPC 100's V DC input sock-
(H1+H3)
ets to protect yourself and the CPC 100 from high-voltage hazards.
C W-U / H3-H1 u-w / X1-X3
C W-(U+V) / H3- w-v / X3-X2
Dz6 V/H2 w/X3 u/X1 A U-V / H1-H2 v-u / X2-X1 1 (H1+H2)
U/H1 W/H3 v/X2
B V-W / H2-H3 w-v / X3-X2

C W-U / H3-H1 u-w / X1-X3
Dy11 V/H2 v/X2 A U-(V+W) / H1- u-w / X1-X3 1*√3/2
(H2+H3)
w/X3
U/H1 W/H3 u/X1
B V-(U+W) / H2- v-u / X2-X1

(H1+H3)
C W-(U+V) / H3- w-v / X3-X2
(H1+H2)
CP SA1
Yd11 V/H2 v/X2 A U-(V+W) / H1- u-w / X1-X3 1*√3/2
w/X3 (H2+H3)
U/H1 W/H3 u/X1

B V-(U+W) / H2- v-u / X2-X1
(H1+H3)
C W-(U+V) / H3- w-v / X3-X2
(H1+H2)
Transformer - 3
CPC 100 V 1.43
TRTapCheck (for OLTC)

Use the TRTapCheck test card to measure the winding resistance of the individual taps of a Output range
power transformer’s tap changer, and to check whether the on-load tap changer (OLTC)
switches without interruption. Winding connection
Nominal test
The CPC 100 injects a constant current current Reference temperature
from the 6A DC output into the power Actual specimen temperature
transformer and the current is led via the
I AC / DC input for measurement. Actual test
Alternatively, the current injected from the current
400A DC output is measured internally. Automated tap
taps From this current value and the voltage operation
Measured
measured by the V DC input, the winding voltage at V DC
resistance is calculated. input Tolerance of the
deviation in %
In the moment the tap is changed, the
I AC / DC measuring input detects the
Transformer tap Settling time
sudden, very short drop of the current flow.
identifier and tap
A properly working tap change differs from
number
a malfunctioning one, e.g., an interruption
during the change, by the magnitude of the
ripple and slope values. An interruption will
result in much higher ripple and slope
values than a properly functioning tap Rmeas: Actual resistance
change.
Dev.: Deviation in % between the maximum and the minimum measured values
The ripple and slope values are indicated at evaluated with the settling time.
the TRTapCheck test card’s measurement
Rref.: Temperature-corrected resistance value
table.
Ripple: Samples and holds the biggest measured current ripple that occurred in the
OLTC measuring cycle. It is indicated in % with reference to I DC.
Warning: Never open the measuring circuit while current flows. Dangerous volt- Slope Samples and holds the biggest measured steepness of the falling edge of the
age may occur. actual test current.
Transformer - 4
Transformer
CPC 100 V 1.43
TRTapCheck (for OLTC) Voltage Withstand Test

Tap Changer Test and Measuring the Winding Resistance This test is identical to the voltage withstand test described on page Current Transformer-4.
When testing a tap changer, we recommend: After pressing the Auto Keep Result menu key, the CPC 100 waits until stable
• To inject the same current value for each phase. results with a deviation less than the defined tolerance (in %) within the defined
• To perform tests of each phase, start with the lowest tap through to the highest and continue settling time (  t) are achieved. After then, a new result line is added and the next
backwards down to the lowest tap again. Taps may show quite different results depending measurement starts.
on the direction of the tap movement and defects can behave differently. An interruption
caused by a defective tap changer results in comparatively high measured values for ripple Note: If the CPC 100 is in Auto Keep Result status, the user can end the process by either
and slope. pressing Keep Result or by changing to the Tolerance setting and changing the value. The soft
key Set Current Deviation resumes the value of the current deviation in the Tolerance field.
Example: Results of a tap changer and winding resistance test
For the tap changer test, the last two columns of the table are relevant. Performing a Tap Changer Test
High ripple because inductance is 1. Press the I/O (test start/stop) push-button to start the test.
charged
2. Press Keep Result to save the resistance value of this tap or press Auto Keep
Result. In this case, the CPC 100 waits until stable results within the set
Tolerance and  t are achieved. After then, a new result line is added showing
Values okay because always in the
the number of the next measured tap.
same range
3. Move to the next position on the tap changer.
4. Repeat steps 2 and 3 for all taps you want to measure.
5. Press the I/O (test start/stop) push-button to stop the test and wait until the
transformer windings are discharged.
Tap defective: significantly higher values for ripple and slope. Compared to the properly
functioning tap change of line 5, for the defective tap in line 7 the ripple is about 30 times and
the slope about 15 times higher. Warning: Before disconnecting the transformer under test, ground all transformer
connections.
Transformer - 5
CPC 100 V 1.43
Transformer - 6
Transformer
Resistance
CPC 100 V 1.43
µ Measurement
The Resistance test card provides a total of three output ranges. The test setup depends on 10 m to 10  10  to 20 k
the selected range.
Setup for a m measurement in the 6A DC range: Setup for an  to kmeasurement in the V DC (2 wire) range:
1 µ to 10 m
Setup for a µ measurement in the 400A DC range:
Inject current from the 6A DC output to both sides of the test object. To measure this current,
route it via the I AC/DC input as shown in the figure above. Input V DC measures the voltage
drop, the software calculates the test object’s resistance. At this range, the DC input V DC outputs the current needed to measure the resistance.
Warning: Do not measure on a large inductance in this mode. Use RWinding

Inject current from the 400A DC output to both sides of the test object. Input V DC measures the instead.
voltage drop, the software calculates the test object’s resistance.
Resistance - 1
CPC 100 V 1.43
µ Measurement Winding Resistance Voltage Withstand Test

Output range, select from 400A DC, Select to stop Use the RWinding test card to measure the resistance of a current transformer’s secondary This test is identical to the voltage withstand test described on page Current Transformer-4.
6A DC or V DC (2 wire) test winding as described on page Current Transformer-4.
Nominal test
automatically Alternatively, inject the current directly from the 400A DC output.
current ("n/a" if
when
V DC 2 wire)
measurement is Warning: Connect the CP SA1 discharge box to the CPC 100’s V DC input sock-
done ets to protect yourself and the CPC 100 from high-voltage hazards.
Burden
Highest possible CT
Smallest resistance
possible
resistance
Select to enter
VDC manually
instead of
measuring it
Actual test
current that is
injected into the
test object
Measured voltage Calculated resistance of test object,
drop at the test object R = V DC / I DC
Resistance - 2
Resistance
CPC 100 V 1.43
RGround
Use the RGround test card to determine earth resistance between a substation’s ground Measuring the Ground Resistance of Small Ground Systems Measuring the Ground Resistance of Large Ground Systems
system and a remote auxiliary electrode. To measure the earth resistance, the CPC 100 injects
AC current between the substation’s ground system and a temporary remote auxiliary electrode.
A second auxiliary electrode is used to measure the voltage potential across the substation’s
earth resistance.
Note: Make sure not to position the auxiliary electrode U too close to the substation’s ground
system. If you do so, you measure in a range where the earth resistance may not be linear (see
figure below).
We suggest to test several points using a longer distance to the substation ground. That way
you get a better understanding of where the linear range of the earth resistance lies, and where
the measurements are reliable.
Theoretical resistance characteristic of an earth electrode: Auxiliary
electrode U 90º
Earth resistance in m
(Bird’s-eye view) > 1km
600 U
500 3...5 x a
Auxiliary
400 linear range of earth resistance electrode I
300
 10xa
Auxiliary
200 electrode U
100 a Substation ground U

a= size of the earthing system 3...5 x a
0
Distance a
a I
I a= size of the earthing system
a
Substation A ground Substation B ground
Resistance - 3
CPC 100 V 1.43
RGround
Measuring the Soil Resistivity Calculating the soil resistivity:
=2dR Nominal test current
Legend:
 = soil resistivity
Frequency of test current. Select a
d = distance between auxiliary electrodes (identical between all electrodes)
frequency other than the 50 or
R = calculated resistance as indicated at the RGround test card (R(f)) 60Hz mains frequency to prevent
With the spacing of "d", the test measures the average soil resistivity between the U auxiliary interferences by stray earth
electrodes down to a depth of "d". Therefore, varying "d" also varies the depth of the volume for currents.
which the soil resistivity is to be measured.
Caution: The 6A AC output can carry a life-threatening voltage level at high loop
impedances or open measuring circuits.
Note: To learn how to measure the resistance of a single ground rod in an earthing system, refer Actual test current (rms value)
to the CPC 100 Reference Manual, section "RGround" of chapter "Resistance". The CPC 100
Reference Manual is available in PDF format on the CPC 100 Toolsets or the
CPC 100 Start Page.
Auxiliary Auxiliary Auxiliary Auxiliary Measured voltage between
electrode I electrode U electrode U electrode I
U substation ground and the
auxiliary electrode U (rms value, Calculated ohmic part Calculated inductive
non-selective frequency) and of earth impedance part of earth
d d d phase shift between VRMS and (frequency-selective impedance
IRMS. measurement) (frequency-selective
d= distance measurement)
Resistance - 4
Resistance
Others: Sequencer
CPC 100 V 1.43
General Testing an Overcurrent Relay with an ARC Function

Use the Sequencer test card to define a sequence of states to be applied to a connected test This sequence of four states tests a complete autoreclosure cycle with both a short dead time
*) Note that some of the trigger events offered in the trigger event combo box
object. A sequence of up to 7 states can be defined. The states within that sequence execute (rapid autoreclosure) and a long dead time (slow autoreclosure).
depend on the measured quantity settings below (trigger on measurement).
sequentially. For each state, a trigger signal can be specified to prematurely terminate this state
and execute the next one. Trigger on "Overload": the occurrence or the clearing of an output overload
condition (clearing is delayed by 100 ms to debounce).
A sequence of states can either be executed once from state 1 to state x, or repeated
continuously. Furthermore, the complete sequence can prematurely be terminated if during the **) Setting a time of 0.000 s makes the state infinite. Only a trigger signal will I>
execution of one of its states this state’s specified trigger condition occurs. terminate it.
***) This option can lead to a freeze of the CPC 100 caused by a memory overflow. OFF ON
This can happen if there are too much results in a certain time. In this case, the
Switch off on trigger, i.e., abort sequence when the trigger condition becomes true CPC 100 can only be switched off via the Emergency Stop button. The CPC 100
will work properly again after rebooting the device.
The feature Manual Trigger provides a possibility to manually initiate a trigger
Synchronize with V1 AC (needs up to 200 ms to The sequence is repeated
signal (i.e., a premature termination) of the current state at any time. This manual
synchronize) endlessly.***)
trigger has the same function as an automatic trigger signal.
Press the Add State button to define additional states. Note that the maximum
possible number of states is 6.
Output range selection
States table (state-specific

settings):
• output quantity settings
• trigger specification *)
• duration of state if no trigger
occurs **)
Others: Sequencer - 1
Others:
Sequencer
CPC 100 V 1.43
Testing an Overcurrent Relay with an ARC Function

State 1: "wait for the CB to open" State 3: "wait for the CB to open" Note: For debouncing purposes, at CB closing time measurements, the CPC 100 adds a fixed
time of 100 ms to the measured value. In order to determine the true CB closing time value,
Set to output 400A until the trigger condition "Overload" occurs. Like state 1, see previous figure. these 100 ms need to be deducted from the value displayed in the measurement table.
Here, trigger condition "Overload" means: The CPC 100 cannot
provide the 400A any longer because of the opening CB contact. Time sequence of the four states to test the autoreclosure cycle
Therefore, the opening CB contact terminates state 1.
The measurement table shows for state 1 that the relay time + the CB Fault inception: overcurrent condition occurs
I
opening time lasted 290 ms. CB opens CB autoreclosure
CB opens again
100ms 100ms
State 4: "wait for the CB to close"
Long dead time. Set to output 50A*) until the "Overload" trigger
State 2: "wait for the CB to close" t
condition that started state 4 clears.
Short dead time. Set to output 50A until the "Overload" trigger The measurement table shows for state 4 that the long dead time + *) *)
State 1 State 2 State 3 State 4
condition that started state 2 clears. the CB closing time lasted 3.191 s. This time also includes the short long dead time
The measurement table shows for state 2 that the short dead time + additional time to compensate for the debounce (see note). dead time
the CB closing time lasted 477 ms. This time also includes the The actual value for CB close equals 3.191 s - 100 ms = 3.091 s.
additional time to compensate for the debounce (see note). *)Current values < 50A do not initiate an "Overload" when the current
The actual value for CB close equals 477 ms - 100 ms = 377 ms. circuit opens. For this reason, a nominal current value of 50A was chosen
*) State 2 and 4 incl. the additional 100 ms the CPC 100 adds to compensate for the debounce
here, even though the CB is open. (see note above).
Note that the r.m.s. measurement of IOut reacts slow and therefore
the measurement table does not show the full current.
Others: Sequencer - 2
Others:
Sequencer
Others: Ramping
CPC 100 V 1.43
General
Use the Ramping test card to define a series of ramps to be applied to a connected test object.
The feature Manual Trigger provides a possibility to manually initiate a trigger
A series of up to 5 ramps can be defined. The ramps within that series execute sequentially, and signal (i.e., a premature termination) of the current ramp at any time. This manual I
run from a start to an end value within a set period of time. Ramp 2
trigger has the same function as an automatic trigger signal.
200A
It is possible to specify a trigger signal that prematurely terminates either Press the Add Ramp button to define additional ramps. Note that the maximum
• the entire series of ramps possible number of ramps is 5.
• or the actual ramp only, and then continues with the next one (if any).
Ra
mp
Example of a series of ramps
mp
Start value of ramp
Ra
3
Switch off on trigger, i.e., when a trigger condition becomes true
Ramp 1
Ramp 2
Output range selection & actual
Ramp 3
output value
Ramped quantity & fixed quantity The three ramps defined in the ramps table shown above result in an output signal like this: 1A t
0s 5s 15s 20s
Ramps table (ramp-specific
settings):
• output quantity settings
• ramp duration if no trigger Ramp 1 Ramp 2 Ramp 3
occurs • from 1 A • from 200 A • from 200 A
• trigger specification (set at "Start val:") (end value of ramp 1) (end value of ramp 2)
• to end value 200 A • to end value 200 A • to end value 0 A
(set in line 1 column "A") (set in line 2 column "A") (set in line 3 column "A")
• in 5 s • for 10 seconds • in 5 seconds
(set in line 1 column "s") (set in line 2 column "s") (set in line 3 column "s")
Others: Ramping - 3
Others:
Ramping
CPC 100 V 1.43
Testing Pick Up / Drop Off Value of an Overcurrent Relay

To determine the pick up and the drop off value of a relay, a series of three ramps is defined. Time sequence of the three ramps:
Ramp 1:
The first ramp determines the pick up value, the second one represents a 1 s pause time, and
the third ramp determines the drop off value. Set to output a ramped current I Ramp 2
signal from 100.0A to either
200.0A in 10s, or until the trigger 200A Ramp 3
pick up
condition "Binary" occurs.
I> 170.29A initially defined ramp
Here, trigger condition "Binary"
152.35A
means: the relay contact picks up.
In this moment, ramp 1 terminates drop off
m p1
and the series continues with Ra
ramp 2. 100A
The measurement table shows for
ramp 1 that the relay contact
picked up after 7.175s at a current
value of 170.29A
Ramp 3:
t
Because ramp 1 did not reach the 200A due to the 0A 1s
trigger signal, ramp 3 starts with 170.29A, and then
ramps down to zero with the set steepness (200.0A 0s 7.175s 1.1s 10s 21s
to 0.0A in 10s) until the trigger condition "Binary"
occurs.
Here, trigger condition "Binary" means: the relay
Ramp 2: contact drops off. Since there are no further ramps
defined, in this moment the sequence terminates.
Pause time. Test current output is
"frozen" for 1 s. The measurement table shows for ramp 3 that the
relay contact dropped off 1.1s after ramp 3 started
The CPC 100’s AC OUTPUT feeds the ramped current signal into a CT, which is connected to at a current value of 152.35A.
an overcurrent relay. The overcurrent relay’s trip contact is fed into the CPC 100’s binary input
BinIn, and acts there as a trigger signal.
Others: Ramping - 4
Others:
Ramping
Others: Amplifier
CPC 100 V 1.43
General
Use the Amplifier test card to set the CPC 100 to an "amplifier-like" mode. In this mode, an Starting a high-current output
input signal fed into a synchronization input drives the high-current output’s magnitude, Display of the measured high-current
frequency and phase angle. output signal
Caution: Depending on the measured input signal, setting the amplification factor
Set range
Select between I AC, V1 AC and V2 AC as synchronization inputs. can result in unintentionally high currents. If the magnitude of the input signal is
unknown or uncertain, it is strongly recommended to set the amplification factor to
To prevent saturation, the output signal follows sudden magnitude changes at the
"0" before starting the test.
synchronization input slowly. This smoothening effect delays the follow-up of the output current
up to 250 ms. Measured phase
Set phase angle
Both the "amplification" factor and the phase angle between input and output are set by the user angle between
between input • Set an amplification factor of "0".
in the Amplifier test card. input and output
and output signal • Press I/O (test start / stop) to start the measurement.
signal
Note: Changes in frequency and phase angle may result in unwanted effects. Both frequency
and phase must be held stable. Now the display field shows the measured input value.
Note: The input frequency is limited to a range of 48 ... 62 Hz.
Select • With the measured input value in mind, enter the amplification factor now.
synchronization Value measured • Acknowledge this entry by pressing the handwheel or the Enter key to start the
at output.
synchronization
input (refer
to ”Starting a
high-current
output” in the
Measured input frequency (48 ... 62 Hz) next column).
Set the amplification factor to determine the ratio between input and output signal.
Note: The synchronization input is not automatically range-switching, it is fixed to its maximum
value.
Others: Amplifier - 5
Others:
Amplifier
CPC 100 V 1.43
Amplifier Use Case: GPS-Synchronized 3-Phase System for End-To-End Testing

Settings of Amplifier test card for this example use case:
Test set
CMC 256-3
GPS
synchronization
unit CMGPS
CPC 100 for CPC 100 for CPC 100 for

phase 1 phase 2 phase 3
This example shows how the three current outputs of a CMC 256-3 test set are led to the
synchronization inputs I AC of three CPC 100 test sets to drive their high-current outputs. This
way, the CPC 100 high-current outputs represent the "amplified" CMC 256-3 outputs and, in this
example, are connected to three CTs.
CT 1 CT 2 CT 3
Protection
relay
Others: Amplifier - 6
Others:
Amplifier
Others: Comment
CPC 100 V 1.43
Starting the String Editor Form Editor - Text Editor

The Comment card is inserted to a test procedure in the same manner like a test card. Its To create such a "2 columns" layout use the Form Editor.
Sub. Buers
purpose is to hold a user-defined comment and / or note regarding the actual test procedure or
other important information, such as operational data of a transformer, for example. Sub.: Buers
Trans. TR24
Trans.: TR24
Manuf.: Siemens Manuf. Siemens
This is a user-defined comment and/or Type: KFRM 1863A / 22E
note regarding the actual test procedure. Year: 1955 Type a.s.o.
Se. No.: T-54953

Power: 100 MVA The tab quasi denotes a column-break.
VecGr.: YN/yn0 The difference between Form Editor and Text Editor is that text left of the tab (the "first column",
Uprim: 220.000 V so to speak) cannot be accessed anymore in Text Editor, i.e., it is protected. To add, edit or
delete first column entries use the Form Editor.
Iprim: 262.5 A
Usec: 110.000 V How to change a comment
Isec: 525.0 A If you need to change an existing comment, press Edit. This starts the String Editor.
Uk: 10.2%
Start the appropriate input mode, "Form Editor" or "Text Editor", change the entries of your
choice and press OK.
Press the context-dependent menu key Edit to start the String Editor, the tool for
Enter the first word "Substation" and then a tab. Proceed with "Buers" and a carriage return.
entering text.
Proceed accordingy: How to clear a comment
Press Clear Comment. The context-dependent menu keys change and provide two more keys:
When used for the Comment card, the String Editor differentiates between the input modes Clear All and Clear Text.
"Form Editor" and "Text Editor". After pressing Edit, "Text Editor" is active. With the exception
of the context-sensitive key to switch between these two modes, the user interface is identical.
Clear All: Deletes the entire comment at once, i.e. all text in all columns.
To create "flowing" text with no tabs in it, either input mode can be used. Compose a text of your
choice by selecting the individual characters and symbols needed one by one and confirm them Clear Text: Deletes all to the right of the tab, i.e. everything but the left-hand side column.
by pressing the handwheel. When finished, acknowledge with OK.
Others: Comment - 7
Others:
Comment
Others: TanDelta
CPC 100 V 1.43
General
The TanDelta test card was especially developed for the CP TD1.
The CP TD1 is an optionally available high-precision test system for on-site insulation tests of
high-voltage systems like power and measuring transformers, circuit breakers, capacitors and
isolators. The CP TD1 works as an add-on device to the CPC 100 and is described in chapter
”CP TD1” of this User Manual.
Since the TanDelta test card exclusively belongs to the CP TD1, it is also described in the
CP TD1 Reference Manual.
The TanDelta test card can be accessed from CT, VT, Transformer and Others test card
groups.
Others: TanDelta - 8
Others:
TanDelta
Common Functions
CPC 100 V 1.43
Test Assessment
The test assessment is a manual procedure carried out by the user. The String Editor is used to name or rename test cards, tests and templates as well as to fill out Important special characters
The example below shows an assessment made at a VTRatio test card. However, the the Comment card.
assessment procedure is carried out in the same fashion on all test cards. Any time such an operation becomes necessary, the String Editor starts automatically. carriage return (line feed)
Change case tab (special function in Form Editor mode; refer to page Others-7).
Text field Switch between

form and text To change the default name, and to enter a name of your choice:
editor
Move left • delete the default name by repeatedly pressing the backspace key
Available Move right • enter the new test or folder name by consecutively selecting the characters of your
Assessment choice from the "on-screen keyboard" with the Up / Down keys or by navigating
characters
symbol to it with the handwheel
Finish editing
• acknowledge every selected character by pressing the handwheel or Enter
Template Abort editing,
phrases discard changes
• After the test, set the focus on the assessment symbol by turning the handwheel.
Test not assessed. The number of available characters to choose from depends on the String Editor’s use. If, for
example, a user-defined comment is to be entered in the Comment card, the number of
available characters is bigger than if a test is to be renamed. This difference are special
characters, such as !, ?, _, [ ], etc.
• Use the context-dependent menu keys to assess the test.
Test OK
Test failed
Common Functions - 1
CPC 100 V 1.43
The String Editor

The Template Phrases
The String Editor provides a feature, that allows you to save phrases, i.e., names of test cards,
tests, templates, folders and files. Once these phrases are saved, they can then be selected as
template phrases from the Select a phrase combo box.
Define new template phrase
Delete selected template phrase
Add selected template phrase to the

actual cursor position in text field
How to Save a Phrase

• enter a name of your choice in the way described above
• put the focus on the Select a phrase combo box
• press Add to Phrases to add this name to the list of template phrases.
Common Functions - 2
Common
Functions
CPC 100 Technical Data
CPC 100 V 1.43
Generator / Output Section - Current Outputs Generator / Output Section - Voltage Outputs Internal Measurement of Outputs
Note: For detailed information refer to the section “Technical Data” in the CPC 100 Reference
Manual available in pdf format on the CPC 100 Toolsets or the CPC 100 Start Page.
Range Amplitude5 tmax Imax Powermax5 f Guaranteed accuracy Typical accuracy6
0 … 2 kV 1 min 1.25 A 2500 VA 15 … 400 Hz Output Range Amplitude Phase Amplitude Phase
The output is either voltage or current, and is automatically selected by the software or manually 2kV AC3
by the user. Current and voltage outputs are overload and short-circuit proof and protected 0 … 2 kV >2h 0.5 A 1000 VA 15 … 400 Hz Reading Full Full Reading Full Full
against over-temperature. error scale scale error scale scale
1kV AC 3 0 … 1 kV 1 min 2.5 A 2500 VA 15 … 400 Hz
error error error error
Range Amplitude tmax1 Vmax2 Powermax2 f 0 … 1 kV >2h 1.0 A 1000 VA 15 … 400 Hz
800A AC - 0.20% 0.20% 0.20° 0.10% 0.10% 0.10°
0 … 800 A 25 s 6.0 V 4800 VA 15 … 400 Hz 500V AC3 0 … 500 V 1 min 5.0 A 2500 VA 15 … 400 Hz
400A DC - 0.40% 0.10% - 0.20% 0.05% -
0 … 400 A 8 min 6.4 V 2560 VA 15 … 400 Hz 0 … 500 V >2h 2.0 A 1000 VA 15 … 400 Hz
800A AC3 2000 V 0.10% 0.10% 0.20° 0.05% 0.05% 0.10°
0 … 200 A >2h 6.5 V 1300 VA 15 … 400 Hz 130V AC10 0 … 130 V >2h 3.0 A 390 VA 15 … 400 Hz
1000 V 0.10% 0.10% 0.30° 0.05% 0.05% 0.15°
6A AC 10 0 …6A >2h 55 V 330 VA 15 … 400 Hz 2kV AC 500 V 0.10% 0.10% 0.40° 0.05% 0.05% 0.20°
Output transient characteristics
3A AC10 0 …3A >2h 110 V 330 VA 15 … 400 Hz 5A 0.40% 0.10% 0.20° 0.20% 0.05% 0.10°
0 … 400 A 2 min 6.5 V 2600 VA DC Changes from “off” or a low Changes from a high magnitude to 500 mA 0.10% 0.10% 0.20° 0.05% 0.05% 0.10°
magnitude to a higher magnitude a lower magnitude or “off”
400A DC 0 … 300 A 3 min 6.5 V 1950 VA DC
AC current within one period 300 ms maximum; accordingly less Note: For the individual notes, see “Notes regarding Inputs and Outputs” below.
0 … 200 A >2h 6.5 V 1300 VA DC
for smaller magnitudes
6A DC4, 10 0 …6A >2h 60 V 360 VA DC
AC voltage 1200 ms maximum; accordingly less 300 ms maximum; accordingly less
3
2000A AC with an optional current booster. For more details, refer to page CP CB2-1. for smaller magnitudes for smaller magnitudes
CPC 100 Technical Data - 1

CPC 100 V 1.43
Measuring Inputs Output to Input Synchronization Notes Related to Inputs and Outputs
All input/output values are guaranteed over one year within an ambient temperature of 23° C ±
Guaranteed accuracy Typical accuracy6 Test cards Quick, Test card Amplifier
5° (73 F ± 10 F), a warm-up time longer than 25 min and in a frequency range of 45 … 60 Hz
Sequencer, Ramping
Amplitude Phase Amplitude Phase or DC. Accuracy values indicate that the error is smaller than ± (value read x reading error + full
Input Imped. Range Frequency range 48 … 62 Hz scale of the range x full scale error).
Reading Full Full Reading Full Full
error scale scale error scale scale Synchronization inputs V1 AC V1 AC, V2 AC, I AC 1. With a mains voltage of 230 V using a 2 x 6 m high-current cable at an ambient temperature
error error error error (automatic range switching) (fixed to maximum range) of 23° C ± 5° (73 F ± 10 F)
10A AC 0.10% 0.10% 0.20° 0.05% 0.05% 0.10° 2. Signals below 50 Hz or above 60 Hz with reduced values possible.
Input magnitude 10% of input range full scale
1A AC 0.10% 0.10% 0.30° 0.05% 0.05% 0.15° 3. Output can be synchronized with V1 AC in Quick, Sequencer, Ramping and Amplifier.
Output magnitude 5% of output range full scale
IAC/DC4, 7 < 0.1  4. The input / output is protected with lightning arrestors between the connector and against
10A DC 0.05% 0.15% - 0.03% 0.08% - Settling time 100 ms after 5% of output 1000 ms after 5% of output protective earth. In case of energy above a few hundred Joule the lightning arrestors apply
1A DC 0.05% 0.15% - 0.03% 0.08% - magnitude is reached magnitude is reached a permanent short-circuit to the input / output.
300 V 0.10% 0.10% 0.20° 0.05% 0.05% 0.10° Signal changes All quantities must be ramped No changes of frequency and 5. Signals below 50 Hz or above 200 Hz with reduced values possible.
within 20 signal periods phase. Magnitude changes
30 V 0.10% 0.10% 0.20° 0.05% 0.05% 0.10° 6. 98% of all units have an accuracy better than specified as typical.
without limitation. Output
V1 AC8 500 k
3V 0.20% 0.10% 0.20° 0.10% 0.05% 0.10° follows within 250 ms. 7. Input is galvanically separated from all other inputs
300 mV 0.30% 0.10% 0.20° 0.15% 0.05% 0.10° Phase tolerance 0.5° within the limits as specified above 8. V1 and V2 are galvanically coupled but separated from all other inputs.
3V 0.05% 0.15% 0.20° 0.03% 0.08% 0.10° 9. There are power restrictions for mains voltages below 190V AC.
V2 AC 8, 11 10 M 10. Fuse-protected
300 mV 0.15% 0.15% 0.20° 0.08% 0.08% 0.10°
11. When using the CTRogowski test card, the 3V V2 AC input uses an additional software
30 mV 0.20% 0.50% 0.30° 0.10% 0.25% 0.15°
based integration method. In the range of 50 Hz < f < 60 Hz, this results in a phase shift of
10 V 0.05% 0.15% - 0.03% 0.08% - 90° as well as an additional phase error of +/- 0.1° and an additional amplitude error of +/-
1V 0.05% 0.15% - 0.03% 0.08% - 0.01%. For frequencies in the range of 15 Hz < f < 400 Hz, the phase error is not specified,
V DC4, 7 and the amplitude error can be up to +/- 0.50% higher.
100 mV 0.10% 0.20% - 0.05% 0.10% -
10 mV 0.10% 0.30% - 0.05% 0.15% -
CPC 100
Technical Data
CPC 100 V 1.43
Measuring Inputs Resistance Measurement General

Additional Features of the Measuring Inputs The accuracy of the resistance measurements can be calculated from the respective input and
Display ¼ VGA greyscale LCD display
• Automatic range switching (except test card Amplifier) output specifications.
• Galvanically separated potential groups: I AC / DC; V1 & V2; V DC
• AC frequency range 15 … 400 Hz (except test card Amplifier) 4-wire measurement with 400A DC output and 10V VDC input
Power supply
• Protection of I AC / DC input: 10A FF fuse4 Current Resistance Voltage Typ. error Guaranteed
Single-phase, nominal9 100V AC … 240V AC, 16A
400 A 10  4 mV 0.70% 1.35%
Binary input for dry contacts or voltages up to 300V DC7 Single-phase, permissible 85V AC … 264V AC (L-N or L-L)
400 A 100  40 mV 0.55% 1.10%
Frequency, nominal 50/60 Hz
Trigger criteria Toggling with potential-free contacts or voltages of up to 300 V 400 A 1 m 400 mV 0.50% 0.95%
Power consumption < 3500 VA (< 7000 VA for a time < 10 s)
Input impedance > 100 k 400 A 10 m 4V 0.50% 0.95%
Connection IEC320/C20
Response time 1 ms
4-wire measurement with 6A DC output and 10V VDC input

Environmental conditions
Current Resistance Voltage Typ. error Guaranteed
Operating temperature -10° … +55° C (+14 … +131 F)
6A 100 m 0.6 V 0.35% 0.60%
Storage temperature -20° … +70° C (-4 … +158 F)
6A 1 6V 0.35% 0.60%
Humidity range 5 … 95% relative humidity, no condensation
1A 10  10 V 0.25% 0.40%
Shock IEC68-2-27 (operating), 15 g/11 ms, half-sinusoid
Vibration IEC68-2-6 (operating), 10 … 150 Hz, acceleration 2 g
2-wire measurement with 10V VDC input continuous (20 m/s²); 10 cycles per axis
Current Resistance Voltage Typ. error Guaranteed EMC EN 50081-2, EN 55011, EN 61000-3-2, FCC Subpart B of Part
< 5 mA 100  0.60% 1.20% 15 Class A, EN 50082-2, IEC 61000-4-2/3/4/8, CE conform
(89/336/EEC)
< 5 mA 1 k 0.51% 1.02%
Safety EN 61010-1, EN 60950, IEC 61010-1, produced and tested in
< 5 mA 10 k 0.50% 1.00%
an EN ISO 9001 certified company.
Prepared for IEEE 510, EN 50191, VDE 104

CPC 100 V 1.43
General
Weight and Dimensions
Weight 29 kg (64 lbs), robust case with cover
Dimensions W x H x D: 468 x 394 x 233 mm (18.4 x 15.5 x 9.2"), cover,
without handles.
CPC 100
Technical Data
CP TD1
CP TD1
Safety Instructions Product Description - Designated Use

Note: On principle, the safety instructions relevant to the CPC 100 and its accessories (refer to • Both low-voltage measuring cables must always be well attached and tightly connected to The CP TD1 is an optionally available high-precision test system for on-site insulation tests of
page Preface-1) also apply to the CP TD1. This section lists safety instructions that exclusively the CP TD1’s measuring inputs IN A and IN B. high-voltage systems like power and measuring transformers, circuit breakers, capacitors and
apply to the CP TD1. Make sure to insert the red and blue marked cables into the corresponding measuring isolators. With the add-on device CP TD1, the CPC 100 increases its range of possible
inputs: IN A = red, IN B = blue. applications into high-voltage measurements.
Handling cables Tighten the plugs by turning them until you feel a stop. The internal switched mode power amplifier enables measuring at different frequencies without
• Always turn off the CP TD1 completely before you connect or disconnect any cable Note: Tighten the plugs manually. Do not use any tools for that because that can damage interferences with the mains frequency. Automatic test procedures reduce the testing time to a
(disconnect the CPC 100 from mains or press its Emergency Stop button). the plugs or connectors. minimum. Test reports are generated automatically.
• The high-voltage cable must always be well attached and tightly connected to both the • Do not use any other cables than the ones supplied by OMICRON electronics. The CP TD1 comes with its own test card named TanDelta (Tangent Delta), which provides
CP TD1 and the test object. A loose or even falling off connector at the test object carrying highly accurate measurements of the capacitance Cx and the dissipation factor tan (DF) or
high voltage is life-hazardous. Make sure the connectors are clean and dry before power factor cos (PF), respectively.
connecting.
Both the dissipation factor and the power factor grant information about possible losses in the
At the CP TD1, press the high-voltage cable’s plug to the connector tightly and turn the
insulation material, which are increasing with age and water content. A change of Cx is a
screw cap until you feel a mechanical stop. If you notice a rough-running of the screw-cap,
warning indicator for partial breakdowns between the layers of a bushing or a capacitor.
clean the screw thread and use a lubricant (vaseline recommended).
Additionally, the CP TD1 measures the following quantities:
Note: Tighten the plugs manually. Do not use any tools for that because that can damage
the plugs or connectors. • Actual, apparent and reactive power
Insert the yellow banana plug (the high-voltage cable’s grounding) into the respective plug • Quality factor QF
socket. • Inductance
• Impedance, phase angle
• Do not connect any cable to the test object without a visible grounding of the test object. • Test voltage & current
• The high-voltage cable is double-shielded and therefore safe. However, the last 50 cm (20
inch) of this cable have no shield. Therefore, during a test consider this cable a life wire and The CP TD1 works as an add-on device to the CPC 100. Do not connect the CP TD1 to any
due to the high voltage life-hazardous! other device. Do not use the accessories for applications not indicated in this User Manual.
Note: Any other use of the CP TD1 but the one mentioned above is considered improper use,
Warning: When the CPC 100 is switched on, consider this part of the cable a
and will not only invalidate all customer warranty claims but also exempt the manufacturer from
hazard of electric shock!
its liability to recourse.
• Never remove any cables from the CP TD1 or the test object during a test.
• Keep clear from zones in which high voltages may occur. Set up a barrier or establish similar
adequate means.
CP TD1 - 1
CP TD1
Functional Components Setup of Devices with and without Trolley

• The equipment trolley holds the CPC 100, CP TD1 and all required cables. The trolley is
Equipment trolley To secure the CPC 100 while pulling
Cable drum with equipped with a grounding bar with three knurled screws to ensure a solid grounding to
the trolley, a safety belt is available
double-shielded equipotential ground of all devices.
(not shown).
output cable to feed • If the CPC 100 and CP TD1 are to be operated without trolley, place them on their transport
the high voltage to cases and connect them with the long type data cable CPC 100  CP TD1 (3 m) and the
the test object long-type booster cable CPC 100  CP TD1 (3 m). Each device has to be grounded
CPC 100 separately with a 6 m grounding cable of at least 6 mm².
Data cable CPC 100  CP TD1
(short type). Via this data cable the
CPC 100 software (test card
Cable drum for
TanDelta) controls the CP TD1.
measuring
cables Booster cable
CPC 100  CP TD1
(short type). Via this
cable the CPC 100
controls the CP TD1
High-voltage output voltage.
output with
attached
screw plug and
yellow The CP TD1’s measuring inputs IN A
grounding CPC 100, CP TD1 and IN B, connected to the cable drum
plug. and the equipment for the measuring cables
trolley connected to
the trolley’s
CP TD1 grounding bar and
led to earth.
Equipotential ground Grounding cable min.
6 mm². Swivelling mounting brackets for the CPC 100 (top)
and CP TD1 (bottom)
CP TD1 - 2
CP TD1
CP TD1
CP TD1 Connected to a Power Transformer CP TD1 Connected to CP CAL1 Putting the CP TD1 into Operation
CP TD1 CP TD1 CP CAL1 As the first step, before you set a CPC 100 / CP TD1 measurement setup into
12 kV 12 kV operation, link the CPC 100, CP TD1 and, if applicable, the equipment trolley with
IN a min. 6 mm² grounding cable as displayed on page CP TD1-2.
Never use the CPC 100 / CP TD1 measurement setup without a solid connection
C1 to ground.
IN A IN A
C2 1. Switch off the CPC 100 at the main power switch.
Ix IN B IN B
Ix 2. With trolley:
C3 Properly connect the CPC 100 and CP TD1 grounding terminals to the trolley’s ground bar.
Connect the ground bar to earth. All cables minimum 6 mm².
Measurement Measurement Without trolley:
PE PE Properly connect the CPC 100 and CP TD1 grounding terminals to earth. Both cables
minimum 6 mm².
Booster Serial Booster Serial 3. Connect the CP TD1’s "BOOSTER IN" to the CPC 100’s "EXT. BOOSTER" with the
OMICRON electronics supplied booster cable.
Equipotential
CPC 100 ground 4. Connect the CP TD1’s "SERIAL" to the CPC 100’s "SERIAL" with the OMICRON electronics
CPC 100
supplied data cable. This cable also provides the power supply for the CP TD1.
Power transformer 5. Pull out the measuring cables from the cable drum and connect the test object to the
CP TD1’s measuring inputs IN A and IN B.
6. Pull out the high-voltage cables from the cable drum and connect the test object to the
When using the CP CAL1 for calibration, we recommend to take C1 as reference and to select CP TD1’s high-voltage output.
Equipotential ground the calibration frequency in a range between 50 … 200 Hz. 7. Switch on the CPC 100.
8. Selecting the TanDelta test card from any of the CPC 100’s CT, VT, Transformer or Others
test card groups automatically turns on the CP TD1. If no CP TD1 is connected to the
CPC 100, an error message appears.
9. Set up your measurement in the TanDelta test card (see page CP TD1-5).
10. Press the CPC 100’s I/O (test start / stop) push-button.
CP TD1 - 3
CP TD1
Calibrate the CP TD1 Using a Reference Capacitor Option TH 3631 Application and Test Templates
By connecting a reference capacitor (e.g., optional device CP CAL1) with known values of Use the optional device TH 3631 to measure ambient temperature, the test object temperature For detailed information on the CP TD1 applications, refer to the CP TD1 Reference Manual
capacity Cref and dissipation factor DFref, in mode UST-A the values Cx and DFx can be and humidity. Once these values were measured, enter them into the respective entry fields of delivered with the CP TD1 or available in pdf format on the CPC 100 Start Page.
measured and then compared to the known reference values. the TanDelta test card’s Settings page at "Compensations" (see page CP TD1-6).
If you experience substantial deviations, re-calibrate the CP TD1: Test Templates
• Cx = Cref / Cmeas and The test procedures for designated applications are controlled by templates available on the
• DF / PF + = DFref - DFmeas CPC 100 Toolsets shipped with your CP TD1 or on the CPC 100 Start Page.
as described on page CP TD1-6. Test templates are available for the following areas:
A re-calibration of the CP TD1 is also shown in the test report (.xml file). • power transformers
• instrument transformers
Note: If you change the factory-made calibration, the responsibility for the accuracy of the
• rotating machines
CP TD1 will be in your hands.
• cables and transmission lines
• grounding systems
Calibration tips: • others
• For calibration, set the averaging factor to maximum and the filter bandwidth to ± 5 Hz (refer
to page CP TD1-5).
• To reset to the factory settings, select "DF/PF+" to 0.0 ppm and "Cx" to 1.000 (refer to page
CP TD1-6).
CP TD1 - 4
CP TD1
CP TD1
TanDelta Test Card - Main Page

The TanDelta test card can be accessed from CT, VT, Transformer and Others test card *) “Auto test points” cleared = manual measurement: Applies the set test voltage and **) Measuring modes and their according
groups. frequency to the CP TD1’s output. When the measurement is finished, its results are displayed arrangements of the internal switch-
in the results table. matrix in the CP TD1.
Select "Assessment" to automatically assess the test, clear for no assessment.
“Auto test points” selected = automatic measurement: Enables the output of a series of test The switch-matrix determines what
Enter the nominal values in the entry fields (here "Cref" and "DFref"; availability and naming
points, e.g., combining a series of voltage values with one fixed frequency value creates a capacities are actually measured.
depend on the measuring mode). These values serve as reference for the assessment. Their
voltage ramp. Combining a series of frequency values with one fixed voltage value creates a
tolerance range can be set on the Settings page (see page CP TD1-6).
frequency ramp. Furthermore, a combination of both is possible.
A measurement is rated as ’OK’ if both values are within their tolerance range. The assessment
is displayed in the test point tables’s column "?" • Set a test voltage and frequency of your choice, and press Add to Auto. The values are
entered into the list boxes.
Note: While a test is running, new nominal values can already be entered.
• Set a second test voltage and/or frequency, and again press Add to Auto. The value(s) is/
are appended to the list.
• Repeat this procedure as often as you need.
Note: You cannot enter the same value twice. Double entries are rejected. If you need identical
Test voltage and frequency. test points for an increasing and a decreasing voltage ramp, set values very close to each other,
e.g., 2000 V and 2001 V.
The CP TD1 then puts out the specified list of values as follows:
Select for automatic measurement,
clear for manual measurement.*). 1. All voltages are issued in the exact order they were entered using the first frequency value
of the list.
Selecting enables the list boxes.
2. All voltages are issued once more in the exact order they were entered using the second
frequency value of the list (if any).
Selecting a measuring mode and 3. ... and so forth.
pressing the handwheel displays an
Each combination is one individual measurement, and its result is displayed in the results table
image that shows the according
with an individual line.
arrangement of the internal
measurement switch-matrix.**) Results table. To delete an entry from a list box, place the cursor on the value and press Delete Value. Do
Also refer to page CP TD1-7. delete all values from both list boxes, place the cursor on "Auto test points (V, f)" and press
Delete List.
During the measurement, the list boxes display the current output values.
CP TD1 - 5
CP TD1
TanDelta Test Card - Main Page TanDelta Test Card - Settings Page
Compound measurement setting Pressing the Settings button on the TanDelta main page opens the Settings page allowing you Selecting “Compensations" converts the actually measured dissipation or power factor to
to set additional measurement options. normalized values corresponding to an ambient temperature of 25° C. In doing so, the values
Cp, DF (tan) = parallel capacitance & dissipation factor
Cp, PF (cos) = parallel capacitance & power factor The CP TD1 leaves OMICRON entered at "Compensations" represent the existing ambient condition.
Cp, Ptest = parallel capacitance & power
At "Assessment Limits", set the tolerance of the
Cp, P@10kV = parallel capacitance & power; linearly interpolated to 10 kV test voltage
electronics factory-calibrated. If a main page’s nominal values for the assessment. • Enter oil temperature, ambient temperature (at bushing) and relative humidity first.
Qtest, Stest = reactive & apparent power component needs to be exchanged by a For the capacitance, the tolerance is entered in • Then place the cursor on "k".
Z = impedance with phase angle spare part, the CP TD1 must be re- percent, for the dissipation factor it’s a multiplier.
Cp, Rp = parallel capacitance & parallel resistance The medium the measurement takes place in, oil or air, determines the k-factor.
Ls, Rs = serial inductance & serial resistance
calibrated.
To re-calibrate, set the focus onto the Note: Availability and naming of the entry fields • ANSI C57.12
Cp, QF = parallel capacitance & quality factor
Ls, QF = series inductance & quality factor test card tab designation TanDelta and depend on the measuring mode, e.g., DF and PF The oil temperature is the determining medium for the k-factor.
press Edit Calib to enable the entry are the same entry field. • Bushings
fields: The air temperature at the respective bushing is the determining medium for the k-factor.
Bushings provides three bushing types to select from: RBP (Resin Bonded Paper), RIP
• Cx = correction factor for Cmeas
The averaging factor determines the (Resin Impregnated Paper) and OIP (Oil Impregnated Paper). The k-factor changes
(multiplier)
number of measurements. A factor of 3 accordingly.
• DF/PF + = corrective value added
means: the CP TD1 carries out 3 to dissipation or power factor (can
measurements whose results are then be + or -)
averaged. The higher the factor, the
Note: You must enter your name and Select if you use an external CT.
more accurate the measurement but
the longer the measuring time. press Update Calib to complete the re- The entered ratio is used to calculate
calibration. the measured current accordingly.
See also figure CP TD1 CP CAL1 on
Note: "Use ext. CT" can only be
page CP TD1-3.
selected if there are no measurement
Filter bandwidth of measurement. If selected, the beeper sounds during
results yet.
the entire test. If cleared, the beeper
Note: If the test frequency equals the default frequency (as set at Options | Device Setup),
sounds at the beginning and the end of
the filter bandwidth is always ± 5 Hz, regardless of the set value. This even applies if the option
the test only.
"use default frequency of xx.xx Hz" is not specifically selected.
± 5 Hz means that interferences at frequencies with an offset of  ± 5 Hz from the measuring If selected, the CPC 100 checks whether the shield of the high-voltage cable is connected. For
frequency will not affect the results. some large inductive loads, the CPC 100 can accidentally report shield check error even when
The smaller the filter bandwidth, the longer the measuring time. the shield is connected. If this is the case, it makes sense to clear the check box.
Returns to TanDelta’s main page
CP TD1 - 6
CP TD1
CP TD1
Technical Data of the CP TD1 in Combination with the CPC 100

High-Voltage Output Filter for selective measurements Capacitance Cp (equivalent parallel circuit)
Conditions: Signals below 45 Hz with reduced values possible. Capacitive linear loads. Conditions: f0 = 15 … 400 Hz
Range Resolution Typical accuracy Conditions
Terminal U/f THD I S tmax Filter bandwidth Meas. time Stop band specification (attenuation) error < 0.05% of reading Ix < 8 mA,
f0 ± 5 Hz 2.2 s > 110 dB at fx = f0 ± (5 Hz or more) 1 pF … 3 F 6 digits + 0.1 pF Vtest = 300 V … 10 kV
High-voltage 10 … 12 kV AC < 2% 300 mA 3600 VA > 2 min
output f0 ± 10 Hz 1.2 s > 110 dB at fx = f0 ± (10 Hz or more) error < 0.2% of reading Ix > 8 mA,
15 … 400 Hz 100 mA 1200 VA > 60 min Vtest = 300 V … 10 kV
f0 ± 20 Hz 0.9 s > 110 dB at fx = f0 ± (20 Hz or more)
Measurements Dissipation factor DF (tan)
Test current (RMS, selective)
Test frequencies
Terminal Range Resolution Typical accuracy Conditions
Range Resolution Typical accuracy 0 … 10% 5 digits error < 0.1% of reading f = 45 … 70 Hz,
IN A or IN Ba 0 …5A AC 5 digits error < 0.3% of reading + Ix < 8 mA (capacitive) I < 8 mA,
15 … 400 Hz 0.01 Hz error < 0.005% of reading + 0.005%a
100 nA Vtest = 300 V … 10 kV
error < 0.5% of reading Ix > 8 mA 0 … 100 5 digits error < 0.5% of reading Vtest = 300 V … 10 kV
TanDelta test card: Column “Hz” of the results table
(0 … 10000%) + 0.02%
Special displays in the frequency column “Hz” and their meanings: a
) IN A (red) or IN B (blue), depending on the mode.
*50 Hz (*60 Hz) Measurement mode suppressing the mains frequency Test voltage (RMS, selective) Power factor PF (cos)
interferences; doubles the measurement time.
Range Resolution Typical accuracy Range Resolution Typical accuracy Conditions
!30 Hz The selected test voltage is not available in Automatic
measurement (applies to frequencies below 45 Hz only). 0 … 12000V AC 1V error < 0.3% of reading + 1 V 0 … 10% 5 digits error < 0.1% of reading f = 45 … 70 Hz,
(capacitive) + 0.005%a I < 8 mA,
?xx Hz Results with reduced accuracy, e.g., in case of a low testing Vtest = 300 V … 10 kV
voltage, influences of partial discharge etc.
0 … 100% 5 digits error < 0.5% of reading Vtest = 300 V … 10 kV
+ 0.02%
a
) Reduced accuracy of DF and PF at mains frequency or its harmonics. Mains frequency suppression
available by precisely selecting a mains frequency of *50 Hz or *60 Hz in the “Hz” column.
CP TD1 - 7
CP TD1
Technical Data of the CP TD1 in Combination with the CPC 100

Phase angle  Power P, Q, S (selective) Weight and dimensions
Weight Dimensions (W x H x D)
Range Resolution Typical accuracy Conditions Range Resolution Typical accuracy
CP TD1 test set 25 kg 450 x 330 x 220 mm
-90° … +90° 4 digits error < 0.01° Vtest = 300 V … 10 kV 0 … 3.6 kW 6 digits error < 0.5% of reading + 1 mW
(55.2 lbs) (17.7 x 13 x 8.7”)
0 … 3.6 kvar 6 digits error < 0.5% of reading + 1 mvar without handles
Impedance Z 0 … 3.6 kVA 5 digits error < 0.5% of reading + 1 mVA 38.1 kg 700 x 500 x 420 mm
test set & casea
(84 lbs) (27.5 x 19.7 x 16.5”)
Mechanical Data CP CAL1 test set 8.8 kg 450 x 330 x 220 mm
1 k … 1200M 6 digits error < 0.5% of reading Vtest = 300 V … 10 kV
(19.4 lbs) (17.7 x 13 x 8.7”)
Environmental conditions
without handles
Inductance Lx (equivalent serial circuit)
Operating temperature -10° … +55° C (+14 … +131 F) test set & casea 21 kg 700 x 500 x 420 mm
Transport and storage -20° … +70° C (-4 … +158 F) (46.3 lbs) (27.5 x 19.7 x 16.5”)
Range Resolution Typical accuracy
temperature Cables and equipment 16.6 kg
1 H … 1000 kH 6 digits error < 0.3% of reading
Humidity range 5 … 95% relative humidity, no condensation accessories (36.6 lbs)
Shock IEC68-2-27 (operating), 15 g/11 ms, half-sinusoid equipment and 26.6 kg 680 x 450 x 420 mm
Quality factor QF
casea (58.7 lbs) (26.8 x 17.7 x 16.5”)
Vibration IEC68-2-6 (operating), 10 … 150 Hz, acceleration 2 g
Range Resolution Typical accuracy continuous (20 m/s²); 5 cycles per axis Equipment trolley equipment 14.5 kg
0 … 1000 5 digits error < 0.5% of reading + 0.2% (32 lbs)
EMC EN 50081-2, EN 55011, EN 61000-3-2, FCC Subpart B of Part
> 1000 5 digits error < 5% of reading 15 Class A, EN 50082-2, IEC 61000-4-2/3/4/8, CE conform equipment & carton 18.9 kg 590 x 750 x 370 mm
(89/336/EEC) (41.7 lbs) (23.2 x 29.2 x 14.6”)
Safety EN 61010-1, EN 60950, IEC 61010-1, produced and tested in CP TD1, CPC 100, equipment 85 kg 750 x 1050 x 600 mm
an EN ISO 9001 certified company. equipment & trolley (187.5 lbs) (29.5 x 41.3 x 23.6”)
(without CP CAL1) equipment & packing 125 kg
Prepared for IEEE 510, EN 50191, VDE 104
(275.8 lbs)
a
) Case = robust case, IP22
CP TD1 - 8
CP TD1
CP CU1
CP CU1
Safety Instructions Block Diagram

Note: On principle, the safety instructions relevant to the CPC 100 and its accessories (refer to Operating the Measurement Setup
page Preface-1) also apply to the CP CU1. This section lists safety instructions that exclusively
apply to the CP CU1. • When using the CP GB1, ground it near the place where the connection to the test object is
made. Make sure that the grounding stud is in good condition, clean and free of oxidation.
• Life threatening voltages up to 600 V can appear on all CP GB1 contacts and on all clamps
General
and cables connected to the CP CU1 during the test. Keep safe distance from them.
• Before operating the CP CU1, read the CP CU1 Reference Manual carefully and observe • Before handling the CP CU1 or CP GB1 in any way (even before setting the current range
the safety rules and instructions therein. switch), make sure that the device under test (e.g. overhead lines or power cables) are well I AC (0 … 2.5 A)
• Before handling the CP CU1 or CPC 100 in any way, connect them with a solid connection grounded (e.g. by closing the grounding switch) near the measurement setup. Surge arrestor
of at least 6 mm² cross-section to ground. Ground the CP CU1 as close as possible to the • Ensure that the short-circuit bar is always plugged in the CP CU1 I AC output whenever the
CPC 100. output is not connected to the I AC input of the CPC 100. Fuse 30 A Power transformer Current range switch
• Use the CP GB1 grounding box to connect the CP CU1 to overhead lines and power cables. • Connect the CP CU1 I AC output exclusively to the I AC input of the CPC 100.
For detailed information, see the application-specific "Safety Instructions for Connecting • Before connecting the CP CU1 with the CPC 100, turn off the CPC 100 either by the
CP CU1 to Power Lines" in the CP CU1 Reference Manual. POWER ON/OFF switch or the Emergency Stop button. BOOSTER CT I OUT (0 … 100 A)
• When using the CP GB1, ground it near the place where the connection to the test object is • Set the current range switch on the CP CU1 front panel only when the CPC 100 is turned
made. Make sure that the grounding stud is in good condition, clean and free of oxidation. off and the test object is grounded.
• Make sure that all studs and cables of the CP GB1 are screwed tight. • In addition to the above safety rules follow the application-specific "Safety Instructions for Voltmeter
• Make sure that the test object’s terminals to be connected to the CP CU1 do not carry any Connecting CP CU1 to Power Lines" in the CP CU1 Reference Manual.
voltage potential. During a test, the only power source for a test object may be the CP CU1 • The CP CU1 may be used only as described in "Applications" in the CP CU1 Reference V1 AC (0 … 30 V)
V SENSE (0 … 600 V)
(powered by the CPC 100). The only exception are measurements on overhead lines as Manual. Any other use is not in accordance with the regulations. The manufacturer and/or
described in "Applications" in the CP CU1 Reference Manual. distributor is not liable for damage resulting from improper usage. The user alone assumes Surge arrestor VT
• Use the CP CU1, CP GB1 and their accessories only in a technically sound condition and all responsibility and risk.
when its use is in accordance with the regulations. In particular, avoid disruptions that could
in turn affect safety.
CP CU1 - 1
CP CU1
Functional Elements CP GB1 Grounding Box

The CP GB1 grounding box is a surge arrestor unit for connecting the CP CU1 to the test object. To short the phases, connect the line studs of the CP GB1 as shown below.
I AC output
Equipotential ground V SENSE input If high voltage appears for a short time on the test object’s terminals, an arc discharges the
terminal voltage and extinguishes without destroying the grounding box. If the arc persists for a longer
VT 600 V : 30 V time period, the surge arrestor insulator melts and the terminals are short-circuited to ground,
Location to store the
short-circuit bar thereby protecting the operating staff, CP CU1 and CPC 100.
V1 AC output
Warning: The CP GB1 grounding box must be used for measurements on over-
head lines or power cables.
To CP CU1
To test object
Surge arrestor
Fuse 30 A Voltmeter
Ground connection
Current range switch I OUT output
BOOSTER input
CT 100 A : 2.5 A
CP CU1 - 2
CP CU1
CP CU1
Measurement Setup Configuring the CPC 100 Connecting the CPC 100 and CP CU1 to Power Lines
The CPC 100 must be configured for the CP CU1. To configure the CPC 100: Safety Instructions
1. Press the Options view selector button to open the Options window.
Warning: A lightning discharge to the line under test can cause injury or possibly
death of the operating staff. Do not connect the measurement setup to overhead
lines if there is a possibility of a thunderstorm over any part of the lines to be mea-
sured.
Warning: Connecting the measurement setup to overhead lines with a life paral-
lel system brings about high-voltage hazards. It is strongly recommended to take
all parallel lines out of service before proceeding
Dangerous zone
Warning: During the grounding switch at the near end of the power line is open,
I AC V1 AC the area around the CP GB1 in the range of 5 m/15 ft and around the CP CU1 in
V1 AC I AC
the range of 2 m/5 ft is a dangerous zone due to high-voltage and mechanical
CP CU1 V SENSE Test object
CPC 100
CP GB1 hazards. Do not enter the dangerous zone. Keep the grounding switch open for a
EXT. BOOSTER BOOSTER I OUT time as short as possible.
(optional)
2. In the External booster combo box, select CU 1. Warning: If you see or hear anything uncommon in the test equipment, e.g. noise
The CT and VT settings are set according to the built-in current and voltage transformers of electrical discharge or lightening of surge arrestors, close the grounding switch
automatically. before touching the measurement setup.
3. Set the current range of the CP CU1 using the current range switch (see page CP CU1-2)
to the value configured by the CPC 100 software.
Warning: Set the current range switch on the CP CU1 front panel only when the
CPC 100 is turned off and the test object is connected to ground with closed
grounding switch near the measurement setup.
Note: Current range settings on the test card and on the CP CU1 front panel must be the same.
CP CU1 - 3
Yes
Yes
Yes
CP CU1 - 4
10 km/6 mi?
2 km/1.5 mi?
Use the 10 A
50 km/30 mi?
current range.
current range.
Start with the 100 A
Is the line longer than

Set 10 A
Set 20 A
Set 50 A
No
No
No
Connect a grounding set in parallel to the closed
grounding disconnector to each phase. Connect it first to
the ground and then to the line. Open the grounding
disconnector and measure the currents in all three
grounding sets. Use the highest measured value of IGS in
the following formula. Close the grounding disconnector
after the measurement is done.
Connecting the CPC 100 and CP CU1 to Power Lines
Yes
Yes
Yes
Yes
Is
Is
Is
Is
greater than 50 V?
greater than 500 V?

greater than 250 V?
greater than 100 V?
Set 10 A
Set 50 A
Set 20 A
Line Length × 2 × 0.4/km (0.64/mi) × IGS

No
No
No
No
Close the grounding disconnector, disconnect the

grounding sets first from the line and then from the
ground. Connect the grounding sets to the CP GB1 and
then to the line. Make the connections to the CP CU1 and
CPC 100 according to the figures on the following pages.
Open the grounding disconnector and read the display
value of the CP CU1. Close the grounding disconnector
afterwards.
Yes
Yes
Yes
Yes
50 V?
500 V?
250 V?
100 V?
Stop! The measurement cannot be performed on this line.

Is the value greater than
Set 50 A
Set 10 A
Set 20 A
No
No
No
No
Try to take parallel lines out of service or to reduce the current flow on the parallel systems.
Start the measurement according to the application

description in one of the following chapters. Try to find out
the maximum possible current at 20 Hz above and below
the mains frequency to avoid overload display.
No
No
No
No
CP CU1
Is 1 A possible?
Are 12 A possible?
Are 30 A possible?
Are 60 A possible?
Set 50 A
Set 10 A
Set 20 A
Yes
Yes
Yes
Yes
Reduce the current for the higher frequencies as needed

to avoid overloads. Try to keep identical settings for all
test cards in one procedure.
CP CU1
Applications and Test Templates Line Impedance Measurement Ground Impedance Measurement
The following application examples show the typical usage of the CP CU1. The test procedures
running on the measurement setup are controlled by templates available on the
CPC 100 Start Page.
For detailed information on the CP CU1 applications, refer to the CP CU1 Reference Manual
delivered with the CP CU1 or available in pdf format on the CPC 100 Start Page.
Far end
Far end
Overhead line
Overhead line
Near endend
Near
90°
V1
V1 AC
AC II AC
AC I AC V1 AC
CPC 100
100 CP CU1 V SENSE V1 AC I AC I AC
CPC
EXT.
EXT. BOOSTER
BOOSTER BOOSTER CP GB1 CPC 100 CP CU1
I OUT
EXT. BOOSTER BOOSTER I OUT
CP GB1
There are seven different measurement loops: A-B (shown here), A-C, B-C, A-G,
B-G, C-G and ABC in parallel to ground (similar to the next figure).
CP CU1 - 5
CP CU1
Measurement of Coupling into Signal Cables Step and Touch Voltage Measurement Technical Data
Output Ranges
Range Current Compliance Voltage @ > 45 Hz

10 A 0 … 10 Arms 500 Vrms 5000 VA (45 … 70 Hz)
20 A 0 … 20 Arms 250 Vrms cos < 1.0 @ 230 V AC mains voltage
cos < 0.4 @ 115 V AC mains voltage
50 A 0 … 50 Arms 100 Vrms for 8 s or 1600 VA continuously
Fence
100 A 0 … 100 Arms 50 Vrms
Accuracy
Impedance Typical Typical V SENSE I OUT Current

Signal cable
Range Accuracy of Accuracy of Voltage Current Range
abs(Z) Phase
0.05 … 0.2  1.0 … 0.5% 1.5 … 0.8° 5 … 20 V 100 A 100 A
0.2 … 2  0.5 … 0.3% 0.8 … 0.5° 20 … 50 V 100 … 25 A 100 A
2…5 0.3% 0.5° 100 V 50 … 20 A 50 A
V2 AC I AC 5 … 25  0.3% 0.5° 100 … 250 V 20 … 10 A 20 A

I AC I AC I AC
I OUT
CPC 100 CP CU1 CPC 100 I OUT 25 … 300  0.3 … 1.0% 0.5 … 1.5° 250 … 500 V 10 … 1.5 A 10 A
CP CU1
CP GB1
EXT. BOOSTER BOOSTER EXT. BOOSTER BOOSTER
CP GB1
There are four measurements with different connections. For detailed information, refer to the For the step and touch voltage measurements using the CP AL1 FFT voltmeter, refer to the
template or the CP CU1 Reference Manual. CP 0502 Application Note.
CP CU1 - 6
CP CU1
CP SB1
CP SB1
Safety Instructions Product Description - Designated Use

Note: On principle, the safety instructions relevant to the CPC 100 and its accessories (refer to DC Output to Test Objects with a High Inductance The CP SB1 is a transformer switch box designated for automatically measuring the ratio and
page Preface-1) also apply to the CP SB1. This section lists safety instructions that exclusively winding resistance, and testing the tap changer of three-phase power transformers. It is an
apply to the CP SB1. When using the DC Output to test power transformers with a high inductance, observe the accessory to the CPC 100. Automatic control of the On-Load Tap Changer (OLTC) is included.
following safety instructions: Testing of power transformers over all taps and all phases is fully automated. Therefore, no
General • Use the TRTapCheck (tap changer winding resistance and on-load tap changer interruption rewiring is required. The CP SB1 is controlled from the CPC 100 via its serial interface. The
check) test card only. results are recorded in the CPC 100 with the ratio and tap changer test cards, and can be
• Make sure to position the CP SB1 in a safe area.
• As long as the CPC 100 software shows the on-screen message "Switch off in progress", analyzed with the computer tool set (CPC 100 Excel File Loader).
• Before connecting or disconnecting test objects and/or cables, turn off the CPC 100 by
NEVER connect or disconnect test objects and/or cables.
either the POWER ON/OFF switch or the Emergency Stop button. Never connect or
• The message "Switch off in progress" notifies you that, while the CPC 100 is deactivating,
disconnect a test object while the outputs are active.
the connected external inductance (this means the test object) still "feeds" voltage potential
• Even if you switched off the CPC 100, wait until the red I/O warning light is fully extinguished.
back into the 6A DC output.
As long as this warning light is lit, there is still voltage and/or current potential on one or more
• The existence of this voltage potential at the 6A DC output is also indicated by a lit LED -
of the outputs.
even if the CPC 100 is switched off.
• When measuring the ratio of power transformers make sure that the test voltage is
• If a test object with a high inductance was connected to the CPC 100, short-out the test
connected to the corresponding high-voltage winding, and the voltage of the low-voltage
object additionally before disconnecting any cables.
winding is the one that is measured. Accidentally mixing up the windings can generate life-
threatening voltages within the transformer.
For example: feeding a voltage of 300 V to the low-voltage winding of a power transformer
that has a ratio of 400000 V : 30000 V, induces a voltage of 4000 V in the transformer's
primary winding.
• Do not operate the CP SB1 under ambient conditions that exceed the temperature and
humidity limits listed in "Technical Data".
• If the CP SB1 or any add-on device or accessory does not seem to function properly, do not
use it anymore. Please call the OMICRON electronics hotline.
• Before handling the CP SB1 or CPC 100 in any way, connect them with a solid connection
of at least 6 mm² cross-section to equipotential ground. Ground the CP SB1 as close as
possible to the CPC 100.
• For the connection between the CPC 100 and CP SB1 only use the specially manufactured
cables supplied by OMICRON electronics.
CP SB1 - 1
CP SB1
Functional Components of the CP SB1 Connecting the CPC 100 and CP SB1 to Power Transformers
The front panel of the CP SB1 provides the following functional components: Safety Instructions
Transformer High Transformer Low
Read the • Transformer High Voltage: • Position the CP SB1 in the safety area and do not enter this area during the entire
Voltage Tap Changer manual
Voltage – Outputs (Source) for the injection of current or voltage on the individual phases of the measurement.
Up Down transformer • Connect the CPC 100 and CP SB1 using the delivered grounding cable.
– Inputs (Measure) for the voltage measurement • Connect the grounding cable of the CP SB1 at a safe grounding point at the transformer.
Note: The inputs and outputs of the respective connections (U/H1, V/H2, W/H3, N/H0) are Note: Do not operate the test equipment without safe connection to ground.
connected to the transformer using Kelvin clamps. • Make sure that all high-voltage connections of the transformer are removed.
• Transformer Low Voltage: • Make sure that all terminals of the transformer are connected to ground.
• Switch off the power supply of the tap changer.
– Outputs (Source) for the injection of current or voltage on the individual phases of the • Connect the Kelvin clamps to the bushings.
transformer • Connect the cables to the Kelvin clamps. Make sure that the cables show upwards and that
– Inputs (Measure) for the voltage measurement each colour is connected to a different phase.
Note: The inputs and outputs of the respective connections (u/X1, v/x2, w/x3, n/X0) are • Connect the cables from the Kelvin clamps’ voltage sense outputs to the CP SB1’s
LEDs connected to the transformer using Kelvin clamps. transformer inputs. Observe the color code.
• Make sure to measure the voltage to ground at the terminals of the tap changer. If no voltage
• Tap Changer: Two potential-free contacts for switching the tap changer is measured, connect the flexible terminal adapters to the "up" and "down" terminals of the
• AC input for connection to the 2KV AC output of the CPC 100 tap changer.
• DC input for connection to the 6A DC output and I AC/DC input of the CPC 100 • Connect the cables ("up", "down") to the CP SB1.
• AC output for connection to the V1 AC input of the CPC 100 • Connect the CP SB1 to the CPC 100 according to ”Functional Components of the CP SB1”
• DC output for connection to the V DC input of the CPC 100 on page CP SB1-2.
• Serial interface for the CPC 100 (TRRatio and TRTapCheck test cards) to control the • Switch on the power supply of the tap changer.
CP SB1 • Remove all grounding connections of the terminals except one per winding. Use Neutral (N)
• Equipotential ground terminal for grounding the CP SB1 close to the position of the for the grounding connection if accessible.
operating staff • Start the measurement according to page Transformer-1 and page Transformer-5.
Serial Equipotential
AC Input DC Input V1 AC Output V DC Output
connection ground
terminal
CP SB1 - 2
CP SB1
CP SB1
Measurement Setup Technical Data

Specifications Environmental Conditions
Characteristic Range Operating temperature –10 … +55° C (+14 … 131° F)

AC Input / V1 AC Output max. 300 Veff Storage and transportation –20 … +70° C (–4 … 158° F)
DC Input max. 6 A DC Max. altitude 2000 m
Transformer High and Low Voltage max. 300 Veff between all connectors and ground Humidity 5 … 95% relative humidity; no condensation
connections Tested according to IEC 68-2-78
Tap Changer Two potential-free contacts, short circuit-protected; Vibration Tested according to IEC 60068-2-6;
0-240 V AC (only AC permitted); frequency range 10 … 150 Hz; acceleration 2 g
Overvoltage Category II; continuous (20 m/s²); 20 cycles per axis
Resistance per contact = max. 4 
I continuous = 0.9 A rms Shock Tested according to IEC 60068-2-27 (operating mode);
15 g / 11 ms, half-sinusoid, 3 shocks in each axis
Supply Via serial interface from the CPC 100 (+15 V)
EMC EN 61326-1 Class A
Overvoltage protection to case with All connections to Tranformer High and Low voltage IEC 61326-1 Class A
surge arrestors side; AC/DC Input; V1 AC / V DC Output FCC Subpart B of Part 15 Class A
EN 61326-1
Select Auto-tap Weight and Dimensions IEC 61326-1
operation mode Safety EN 61010-1
IEC 61010-1
CP SB1 test set 3.5 kg (7.7 lbs) 357 x 235 x 111 mm UL 61010-1
(14.1 x 9.2 x 4.4")
Suitable for usage according to IEEE 510, EN 50191 (VDE 0104), EN 50110-1
test set & case 28.5 kg (62.7 lbs) 700 x 450 x 500 mm (VDE 0105 Part 100)
(27.6 x 17.7 x 19.7")
Housing and transport case IP20 according to EN 60529
CP SB1 - 3
CP SB1
CP SB1 - 4
CP SB1
CP CB2
CP CB2
General Operation Modes of the CP CB2

For test applications requiring up to 2000 A. 2000 A mode: 1000 A mode:
The output current of the CPC 100 can be increased up to 2000 A by means of an electronically
controlled current booster. The CP CB2 can be connected close to the busbar using short high-
current cables and to the CPC 100 with a long control cable.
Select the CP CB2 as external booster on the Device Setup tab in the Options menu:
Burden
Burden
Note: If you select the CP CB2 as external booster on the Device Setup tab in the Options
menu, it will be saved as default value for new test cards. However, it is also possible to select
the external booster individually on the test cards. The settings for already inserted test cards
will only be changed if no test results are available yet.
CP CB2 - 1
CP CB2
Technical Data
Notes regarding the CP CB2
Current outputs
1. With a mains voltage of 230 V using a 2 x 0.6 m high-current cable at an ambient
Range Amplitude tmax1 Vmax2 Powermax2 f
temperature of 23° C ± 5° (73 F ± 10 F)
1000 A AC 0 … 1000 A 25 s 4.90 V 4900 VA 15 … 400 Hz 2. Signals below 50 Hz or above 60 Hz with reduced values possible
0 … 500 A 30 min 5.00 V 2500 VA 15 … 400 Hz
Caution: Make sure to establish series or parallel connection, depending on the
2000 A AC 0 … 2000 A 25 s 2.45 V 4900 VA 15 … 400 Hz selected range on the test card.
Internal measurement of outputs

Guaranteed accuracy Typical accuracy
Amplitude Phase Amplitude Phase
Output
Reading Full scale Full scale Reading Full scale Full scale
error error error error error error
2000 A AC 0.25% 0.25% 0.50° 0.13% 0.13% 0.25°
1000 A AC 0.25% 0.25% 0.50° 0.13% 0.13% 0.25°
Weight and Dimensions
CP CB2 test set 16 kg (35.3 lbs) 186 x 166 x 220 mm (7.3 x 6.5 x 8.7”),
without handle.
test set & case 25 kg (55.1 lbs) 700 x 450 x 360 mm (27.6 x 17.7 x
14.2”)
CP CB2 - 2
CP CB2

CPC 100 User Manual v1.43

Uploaded by

Copyright:

Available Formats

CPC 100 User Manual v1.43

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

CPC 100 User Manual v1.43

Uploaded by

Copyright:

Available Formats

Manual Information Contact Information / Technical Support

Article Number VESD0601 - Manual Version: CPC100LITE.AE.6

CPC 100 This product includes software developed by Intrinsyc Software.

Safety Instructions for the CPC 100 and its Accessories

Safety Instructions for the CPC 100 and its Accessories

Functional Components of the CPC 100

Add test cards

VDC INPUT I/O

Functional Components of the CPC 100

Mains power supply, Automatic circuit POWER ON /OFF

Test Procedure Overview The CPC 100 File System

Main File Operations Menu

Opens the submenu File (refer to “Submenu File” on page 5)

The CPC 100 File System The Options Menu

The Options Menu

The Options Menu Customizing Your Working Environment Accelerator Keys

Change to Test Procedure Overview. Quick test card

Select from voltage transformer (VT) test cards

Select from other test applications

Settings Page Measuring with Quick

Synchronizing Output Frequency with V1 AC Trigger Settings

Measured Select to enter

Ratio Iprim. / Isec.: Polarity: See “CTRatio (with

CTRatio (with Burden) - The Option Measure Burden CTBurden

CTExcitation (Knee point)

Winding Resistance Voltage Withstand Test

Voltage Withstand Test Polarity Check

Polarity Check CTRatioV (with Voltage)

A T on / T off ratio of 2.000 s / 9.000 s means the signal is applied for 2

CTRatio (with Voltage) CTRogowski

CTRogowski CTLowPower (Ratio)

VTBurden Voltage Withstand Test Polarity Check

Output Nominal secondary voltage

Use current clamp

TRRatio (per Tap) Settings Page

Operation mode Performing a TRRatio Test (per Tap)

Settings Page TRRatio (per Tap)

U/H1 W/H3 u/X1 w/X3 U/H1 W/H3 v/X2

TRRatio (per Tap) Winding Resistance

U/H1 W/H3 v/X2

B V-W / H2-H3 w-v / X3-X2

B V-(U+W) / H2- v-u / X2-X1

U/H1 W/H3 u/X1

TRTapCheck (for OLTC)

TRTapCheck (for OLTC) Voltage Withstand Test

Warning: Do not measure on a large inductance in this mode. Use RWinding

µ Measurement Winding Resistance Voltage Withstand Test

100 a Substation ground U

General Testing an Overcurrent Relay with an ARC Function

Output range selection

States table (state-specific

Testing an Overcurrent Relay with an ARC Function

Testing Pick Up / Drop Off Value of an Overcurrent Relay

Amplifier Use Case: GPS-Synchronized 3-Phase System for End-To-End Testing

CPC 100 for CPC 100 for CPC 100 for

Starting the String Editor Form Editor - Text Editor

Se. No.: T-54953

Text field Switch between

The String Editor

Define new template phrase