Basic Knowledge of Electronic Components

Electronic circuits are formed by connecting various electronic components. Generally,

electronic components can be divided into passive and active components.

Passive Components

• Do not need power supply for operation.

• Dissipate power, making output signal power smaller than input signal power..
• Common passive components include resistor (R), inductor (L) and capacitor (C).

Resistors

• The resistor's function is to reduce the flow of electric current.

• This symbol is used to indicate a resistor in a circuit diagram, known as a

schematic.

• Resistance value is designated in units called the "Ohm." A 1000 Ohm resistor is
typically shown as 1K-Ohm (kilo ohm), and 1000 K-Ohms is written as 1M-Ohm (mega
ohm).

• There are two classes of resistors: “fixed resistors” and the “variable resistors”. They
are also classified according to the material from which they are made. The typical
resistor is made of either carbon film or metal film. There are other types as well, but
these are the most common.

• The resistance value of the resistor is not the only thing to consider when selecting a
resistor for use in a circuit. The "tolerance" and the electric power ratings of the resistor
are also important.

• The tolerance of a resistor denotes how close it is to the actual rated resistance value.
For example, a ±5% tolerance would indicate a resistor that is within ±5% of the specified
resistance value.

• The power rating indicates how much power the resistor can safely tolerate. Just like
you wouldn't use a 6 volt flashlight lamp to replace a burned out light in your house, you
wouldn't use a 1/8 watt resistor when you should be using a 1/2 watt resistor.

• The maximum rated power of the resistor is specified in Watts.

Power is calculated using the square of the current (I2) x the resistance value (R) of the
resistor. If the maximum rating of the resistor is exceeded, it will become extremely hot,
and even burn.

• Resistors in electronic circuits are typically rated 1/8W, 1/4W, and 1/2W. 1/8W is
almost always used in signal circuit applications.

• When powering a light emitting diode, a comparatively large current flow through the
resistor, so you need to consider the power rating of the resistor you choose.

1/20
Rating Electric Power

• For example, to power a 5V circuit using a 12V supply, a three-terminal voltage

regulator is usually used.

• However, if you try to drop the voltage from 12V to 5V using only a resistor, then
you need to calculate the power rating of the resistor as well as the resistance value.
• At this time, the current consumed by the 5V circuit needs to be known.
Here are a few ways to find out how much current the circuit demands.
1. Assemble the circuit and measure the actual current used with a multi-meter.
2. Check the component's current use against a standard table.

• Assume the current consumed is 100mA (milliamps) in the following example.

7V must be dropped with the resistor. The resistance value of the resistor becomes 7V /
0.1A = 70(ohm). The consumption of electric power for this resistor becomes 0.1A x
0.1A x 70 ohm = 0.7W.

• Generally, it's safe to choose a resistor which has a power rating of about twice the
power consumption needed.

Resistance value

• As for the standard resistance value, the values used can be divided like a logarithm.
For example,
1. In the case of E3, the values [1], [2.2], [4.7] and [10] are used. They divide 10 into
three, like a logarithm.
2. In the case of E6: [1], [1.5], [2.2], [3.3], [4.7], [6.8], [10].
3. In the case of E12: [1], [1.2], [1.5], [1.8], [2.2], [2.7], [3.3], [3.9], [4.7], [5.6], [6.8],
[8.2], [10].

• It is because of this that the resistance value is seen at a glance to be a discrete value.
The resistance value is displayed using the “colour code” (the coloured bars/the coloured
stripes), because the average resistor is too small to have the value printed on it with
numbers.

• You had better learn the colour code, because almost all resistors of 1/2W or less use
the colour code to display the resistance value.

Fixed Resistors

• A fixed resistor is one in which the value of its resistance cannot change.

Carbon Film Resistors

• This is the most general purpose, cheap resistor. Usually the tolerance of the
resistance value is ±5%. Power ratings of 1/8W, 1/4W and 1/2W are frequently used.

2/20
 • Carbon film resistors have a disadvantage; they tend to be electrically noisy. Metal
film resistors are recommended for use in analogue circuits. However, I have never
experienced any problems with this noise.

• The physical size of the different resistors are as follows:

1/8W

1/4W

1/2W

Rating
Thickness Length
power
(W) (mm) (mm)
8/1 2 3
4/1 2 6
2/1 3 9

Variable Resistors

• There are two general ways in which variable resistors are used. One is the variable
resistor which value is easily changed, like the volume adjustment of Radio. The other is
semi-fixed resistor that is not meant to be adjusted by anyone but a technician. It is used
to adjust the operating condition of the circuit by the technician. Semi-fixed resistors are
used to compensate for the inaccuracies of the resistors, and to fine-tune a circuit. The
rotation angle of the variable resistor is usually about 300 degrees. Some variable
resistors must be turned many times to use the whole range of resistance they offer. This
allows for very precise adjustments of their value. These are called "Potentiometers" or
"Trimmer Potentiometers."

• In the photograph above, the variable resistor typically used for volume controls can
be seen on the far right. Its value is very easy to adjust.

3/20
• The four resistors at the centre of the photograph are the semi-fixed type. These ones
are mounted on the printed circuit board.

• The two resistors on the left are the trimmer potentiometers.

• This symbol is used to indicate a variable resistor in a circuit diagram.

• There are three ways in which a variable resistor's value can change according to the
rotation angle of its axis.

• When type "A" rotates clockwise, at first, the resistance value changes slowly and
then in the second half of its axis, it changes very quickly.

• The "A" type variable resistor is typically used for the volume control of a radio, for
example. It is well suited to adjust a low sound subtly. It suits the characteristics of the
ear. The ear hears low sound changes well, but isn't as sensitive to small changes in loud
sounds. A larger change is needed as the volume is increased. These "A" type variable
resistors are sometimes called "audio taper" potentiometers.

• As for type "B", the rotation of the axis and the change of the resistance value are
directly related. The rate of change is the same, or linear, throughout the sweep of the
axis. This type suits a resistance value adjustment in a circuit, a balance circuit and so on.
They are sometimes called "linear taper" potentiometers.

• Type "C" changes exactly the opposite way to type "A". In the early stages of the
rotation of the axis, the resistance value changes rapidly, and in the second half, the
change occurs more slowly. This type isn't too much used. It is a special use.

• As for the variable resistor, most are type "A" or type "B".

4/20
Resistor Colour Code

Valu Tolerance
Color Multiplier
e (%)
Black 0 0 -
Brown 1 1 ±1
Red 2 2 ±2
Orange 3 3 ±0.05
Yellow 4 4 -
Green 5 5 ±0.5
Blue 6 6 ±0.25
Violet 7 7 ±0.1
Gray 8 8 -
White 9 9 -
Gold - -1 ±5
Silver - -2 ±10
None - - ±20

Example 1:

(Brown=1), (Black=0), (Orange=3)

10 x 103 = 10 kilo-ohm
Tolerance (Gold) = ±5%

Example 2:

(Yellow=4), (Violet=7), (Black=0), (Red=2)

470 x 102 = 47 kilo-ohm
Tolerance (Brown) = ±1%

5/20
Capacitors

• The capacitor's function is to store electricity, or electrical energy. The capacitor also
functions as a filter, passing alternating current (AC), and blocking direct current (DC).
This symbol is used to indicate a capacitor in a circuit diagram.

• The capacitor is constructed with two electrode plates facing each other, but separated
by an insulator.

• When DC voltage is applied to the capacitor, an electric charge is stored on each

electrode. While the capacitor is charging up, current flows. The current will stop flowing
when the capacitor has fully charged.

• When a circuit tester, such as an analogue meter set to measure resistance, is

connected to a 10 microfarad (µF) electrolytic capacitor, a current will flow, but only for
a moment. You can confirm that the meter's needle moves off of zero, but returns to zero
right away.
When you connect the meter's probes to the capacitor in reverse, you will note that
current once again flows for a moment. Once again, when the capacitor has fully charged,
the current stops flowing. So the capacitor can be used as a filter that blocks DC current.
(A "DC cut" filter.) However, in the case of alternating current, the current will be
allowed to pass. Alternating current is similar to repeatedly switching the test meter's
probes back and forth on the capacitor. Current flows every time the probes are switched.

• The value of a capacitor (the capacitance), is designated in units called the Farad (F).
The capacitance of a capacitor is generally very small, so units such as the microfarad
(10-6F), nanofarad (10-9F), and picofarad (10-12F) are used. Recently, a new capacitor with
very high capacitance has been developed. The Electric Double Layer capacitor has
capacitance designated in Farad units. These are known as "Super Capacitors."

• Sometimes, a three-digit code is used to indicate the value of a capacitor. There are
two ways in which the capacitance can be written. One uses letters and numbers, the other
uses only numbers. In either case, there are only three characters used. [10n] and [103]
denote the same value of capacitance. The method used differs depending on the
capacitor supplier. In the case that the value is displayed with the three-digit code, the 1st
and 2nd digits from the left show the 1st figure and the 2nd figure, and the 3rd digit is a
multiplier which determines how many zeros are to be added to the capacitance.
Picofarad (pF) units are written this way.

• For example, when the code is [103], it indicates 10 x 10 3, or 10,000pF = 10

nanofarad (nF) = 0.01 microfarad (µF). If the code happened to be [224], it would be 22 x
104 = or 220,000pF = 220nF = 0.22µF. Values under 100pF are displayed with 2 digits
only. For example, 47 would be 47pF.

• The capacitor has an insulator (the dielectric) between 2 sheets of electrodes.

Different kinds of capacitors use different materials for the dielectric.

6/20
Breakdown Voltage

• When using a capacitor, you must pay attention to the maximum voltage which can be
used. This is the "breakdown voltage". The breakdown voltage depends on the kind of
capacitor being used. You must be especially careful with electrolytic capacitors because
the breakdown voltage is comparatively low. The breakdown voltage of electrolytic
capacitors is displayed as Working Voltage. The breakdown voltage is the voltage that
when exceeded will cause the dielectric (insulator) inside the capacitor to break down and
conduct. When this happens, the failure can be catastrophic.

• Different types of capacitors are introduced below:

Electrolytic Capacitors (Electrochemical type capacitors)

• Aluminium is used for the electrodes by using a thin oxidization membrane. Large
values of capacitance can be obtained in comparison with the size of the capacitor,
because the dielectric used is very thin.

• The most important characteristic of electrolytic capacitors is that they have polarity.
They have a positive and a negative electrode. [Polarised] This means that it is very
important which way round they are connected. If the capacitor is subjected to voltage
exceeding its working voltage, or if it is connected with incorrect polarity, it may burst. It
is extremely dangerous, because it can quite literally explode. Make absolutely no
mistakes.

• Generally, in the circuit diagram, the positive side is indicated by a "+" (plus) symbol.
Electrolytic capacitors range in value from about 1µF to thousands of µF. This type of
capacitor is mainly used as a ripple filter in a power supply circuit, or as a filter to bypass
low frequency signals, etc. Because this type of capacitor is comparatively similar to the
nature of a coil in construction, it isn't possible to use for high-frequency circuits. (It is
said that the frequency characteristic is bad.)

• The photograph above is an example of the different values of electrolytic capacitors

in which the capacitance and voltage differ.

• From the left to right:

1. 1µF (50V) [diameter 5 mm, high 12 mm]
2. 47µF (16V) [diameter 6 mm, high 5 mm]
3. 100µF (25V) [diameter 5 mm, high 11 mm]

7/20
 4. 220µF (25V) [diameter 8 mm, high 12 mm]
5. 1000µF (50V) [diameter 18 mm, high 40 mm]

• The size of the capacitor sometimes depends on the manufacturer. So the sizes shown
here on this page are just examples.

• In the photograph above, the mark indicating the negative lead of the component can
be seen. You need to pay attention to the polarity indication so as not to make a mistake
when you assemble the circuit.

Ceramic Capacitors

• Ceramic capacitors are constructed with materials such as titanium

acid barium used as the dielectric. Internally, these capacitors are not constructed as a
coil, so they can be used in high frequency applications. Typically, they are used in
circuits which bypass high frequency signals to ground.

• These capacitors have the shape of a disk. Their capacitance is

comparatively small.

• The capacitor above is a 100pF capacitor with a diameter of about 3

mm.
The capacitor on the right side is printed with 103, so 10 x 10 3pF becomes 0.01 µF. The
diameter of the disk is about 6 mm.

• Ceramic capacitors have no polarity. Ceramic capacitors should not be

used for analogue circuits, because they can distort the signal.

Multilayer Ceramic Capacitors

• The multilayer ceramic capacitor has a many-layered dielectric. These capacitors are
small in size, and have good temperature and frequency characteristics.

8/20
 • Square wave signals used in digital circuits can have a comparatively high
frequency component included.

• This capacitor is used to bypass the high frequency to ground.

• In the photograph, the capacitance of the component on the left is displayed as 104.
So, the capacitance is 10 x 104 pF = 0.1 µF. The thickness is 2 mm, the height is 3 mm,
and the width is 4 mm.

• The capacitor to the right has a capacitance of 103 (10 x 103 pF = 0.01 µF). The
height is 4 mm, the diameter of the round part is 2 mm. These capacitors are not
polarized. That is, they have no polarity.

Polystyrene Film Capacitors

• In these devices, polystyrene film is used as the dielectric. This type of capacitor is
not for use in high frequency circuits, because they are constructed like a coil inside.
They are used well in filter circuits or timing circuits which run at several hundred KHz
or less.

• The component shown above has a red colour due to the copper leaf used for the
electrode. The silver colour is due to the use of aluminium foil as the electrode.

• The device on the left has a height of 10 mm, is 5 mm thick, and is rated 100pF.
The device in the middle has a height of 10 mm, 5.7 mm thickness, and is rated 1000pF.
The device on the right has a height of 24 mm, is 10 mm thick, and is rated 10000pF.
These devices have no polarity.

Polyester Film Capacitors

• This capacitor uses thin polyester film as the dielectric. They are not high tolerance,
but they are cheap and handy. Their tolerance is about ±5% to ±10%.

9/20
 • From the left in the photograph,
Capacitance: 0.001 µF (printed with 001K)
[the width 5 mm, the height 10 mm, the thickness 2 mm]
Capacitance: 0.1 µF (printed with 104K)
[the width 10 mm, the height 11 mm, the thickness 5mm]
Capacitance: 0.22 µF (printed with .22K)
[the width 13 mm, the height 18 mm, the thickness 7mm]

• Care must be taken, because different manufacturers use different methods to denote
the capacitance values.

• Here are some other polyester film capacitors.

• Starting from the left,

Capacitance: 0.0047 µF (printed with 472K)
[the width 4mm, the height 6mm, the thickness 2mm]
Capacitance: 0.0068 µF (printed with 682K)
[the width 4mm, the height 6mm, the thickness 2mm]
Capacitance: 0.47 µF (printed with 474K)
[the width 11mm, the height 14mm, the thickness 7mm]
These capacitors have no polarity.

Polypropylene Capacitors

• This capacitor is used when a higher tolerance is necessary than polyester capacitors
offer. Polypropylene film is used for the dielectric. It is said that there is almost no change
of capacitance in these devices if they are used with frequencies of 100 kHz or less. The
pictured capacitors have a tolerance of ±1%.

• From the left in the photograph,

Capacitance: 0.01 µF (printed with 103F)

10/20
 [the width 7mm, the height 7mm, the thickness 3mm]
Capacitance: 0.022 µF (printed with 223F)
[the width 7mm, the height 10mm, the thickness 4mm]
Capacitance: 0.1 µF (printed with 104F)
[the width 9mm, the height 11mm, the thickness 5mm]

• These capacitors have no polarity.

Mica Capacitors

• These capacitors use Mica for the dielectric. Mica capacitors have good stability
because their temperature coefficient is small. Because their frequency characteristic is
excellent, they are used for resonance circuits, and high frequency filters. Also, they have
good insulation, and so can be utilized in high voltage circuits. It was often used for
vacuum tube style radio transmitters, etc. Mica capacitors do not have high values of
capacitance, and they can be relatively expensive.

• Pictures above are "Dipped mica capacitors." These can handle up to 500 volts.
The capacitance from the left,
Capacitance: 47pF (printed with 470J)
[the width 7mm, the height 5mm, the thickness 4mm]
Capacitance: 220pF (printed with 221J)
[the width 10mm, the height 6mm, the thickness 4mm]
Capacitance: 1000pF (printed with 102J)
[the width 14mm, the height 9mm, the thickness 4mm]

• These capacitors have no polarity.

11/20
Active Components

• Needs electrical power supply.

• Power of output signal can be higher than the power of input signal (with power
drawn from the power supply).
• Familiar active components include semiconductor devices such as diode, transistor
and IC.

Diodes

• A diode is a semiconductor device which allows current to flow through it in only one
direction. Although a transistor is also a semiconductor device, it does not operate the
way a diode does. A diode is specifically made to allow current to flow through it in only
one direction.

• Some ways in which the diode can be used are listed here.

1. A diode can be used as a rectifier that converts AC (Alternating Current) to DC

(Direct Current) for a power supply device.
2. Diodes can be used to separate the signal from radio frequencies.
3. Diodes can be used as an on/off switch that controls current.

• This symbol is used to indicate a diode in a circuit diagram.

• The meaning of the symbol is (Anode) (Cathode). Current flows from

the anode side to the cathode side.
• Although all diodes operate with the same general principle, there are different
types suited to different applications. For example, the following devices are best used for
the applications noted.

Voltage Regulation Diode (Zener Diode)

• The circuit symbol is . It is used to regulate voltage, by taking advantage of the

fact that Zener diodes tend to stabilize at a certain voltage when that voltage is applied in
the opposite direction.

Light Emitting Diode

• The circuit symbol is . This type of diode emits light when current flows
through it in the forward direction. (Forward biased.)

12/20
Variable Capacitance Diode

• The circuit symbol is . The current does not flow when applying the voltage of
the opposite direction to the diode. In this condition, the diode has a capacitance like the
capacitor. It is a very small capacitance. The capacitance of the diode changes when
changing voltage. With the change of this capacitance, the frequency of the oscillator can
be changed.

• The graph above shows the electrical characteristics of a typical diode.

• When a small voltage is applied to the diode in the forward direction, current flows
easily.
Because the diode has a certain amount of resistance, the voltage will drop slightly as
current flows through the diode. A typical diode causes a voltage drop of about 0.6 - 1V
(VF) (In the case of silicon diode, almost 0.6V.) This voltage drop needs to be taken into
consideration in a circuit which uses many diodes in series. Also, the amount of current
passing through the diodes must be considered.

• When voltage is applied in the reverse direction through a diode, the diode will have a
great resistance to current flow. Different diodes have different characteristics when
reverse-biased. A given diode should be selected depending on how it will be used in the
circuit. The current that will flow through a diode biased in the reverse direction will vary
from several mA to just µA, which is very small.

• The limiting voltages and currents permissible must be considered on a case by case
basis. For example, when using diodes for rectification, part of the time they will be
required to withstand a reverse voltage. If the diodes are not chosen carefully, they will
break down.

13/20
Rectification / Switching / Regulation Diode

• The stripe stamped on one end of the diode shows indicates the polarity of the diode.
The stripe shows the cathode side.

• The top two devices shown in the picture are diodes used for rectification. They are
made to handle relatively high currents. The device on top can handle as high as 6A, and
the one below it can safely handle up to 1A.

• However, it is best used at about 70% of its rating because this current value is a
maximum rating.

• The third device from the top (red colour) has a part number of 1S1588. This diode is
used for switching, because it can switch on and off at very high speed. However, the
maximum current it can handle is 120 mA. This makes it well suited to use within digital
circuits. The maximum reverse voltage (reverse bias) this diode can handle is 30V.

• The device at the bottom of the picture is a voltage regulation diode with a rating of
6V. When this type of diode is reverse biased, it will resist changes in voltage. If the input
voltage is increased, the output voltage will not change. (Or any change will be an
insignificant amount.) While the output voltage does not increase with an increase in
input voltage, the output current will.

• This requires some thought for a protection circuit so that too much current does not
flow. The rated current limit for the device is 30 mA. Generally, a 3-terminal voltage
regulator is used for the stabilization of a power supply. Therefore, this diode is typically
used to protect the circuit from momentary voltage spikes. 3 terminal regulators use
voltage regulation diodes inside.

14/20
Diode Bridge

• Rectification diodes are used to make DC from AC. It is possible to do only 'half
wave rectification' using 1 diode. When 4 diodes are combined, 'full wave rectification'
occurs.

Light Emitting Diode (LED)

• Light emitting diodes must be chosen according to how they will be used, because
there are various kinds. The diodes are available in several colours. The most common
colours are red and green, but there are even blue ones.

• The device on the far right in the photograph combines a red LED and green LED in
one package. The component lead in the middle is common to both LEDs. As for the
remaining two leads, one side is for the green, the other for the red LED. When both are
turned on simultaneously, it becomes orange.

• When an LED is new out of the package, the polarity of the device can be determined
by looking at the leads. The longer lead is the Anode side, and the short one is the
Cathode side.

• The polarity of an LED can also be determined using a resistance meter, or even a 1.5
V battery.

15/20
 • When using a test meter to determine polarity, set the meter to a low resistance
measurement range. Connect the probes of the meter to the LED. If the polarity is correct,
the LED will glow. If the LED does not glow, switch the meter probes to the opposite
leads on the LED. In either case, the side of the diode which is connected to the black
meter probe when the LED glows, is the Anode side. Positive voltage flows out of the
black probe when the meter is set to measure resistance.

• It is possible to use an LED to obtain a fixed voltage.

• The voltage drop (forward voltage or VF) of an LED is comparatively stable at just
about 2V.

Transistors

• Active components that amplify electric current.

• Can be used to amplify signal or switching purposes.

• Two common types: Bipolar Junction Transistors (BJT) and Field Effect Transistors
(FET).

• BJT – output current controlled by input current. PNP type and NPN type

• FET – output current controlled by input voltage.

• Can be further divided according to the nominal direction of current flow: BJT – NPN
& PNP; FET – N type & P type.

• Transistors are 3 terminal devices with various outward appearance (package), eg:

16/20
Integrated Circuits (ICs)

An integrated circuit contains transistors, capacitors, resistors and other parts packed in high
density on one chip. The transistors, resistors, and capacitors are formed very small, and in
high density on a foundation of silicon. They are formed by a variation of printing
technology.
There are many kinds of ICs, including special use ICs. ICs have various kind of package, the
most common being the DIL (dual in line) package.

(Modified from articles of Seiichi Inoue, Hobby of Electronic Circuit Engineering,

http://www.hobby-elec.org/e_menu.htm)

17/20
Appendix: Common Tools for Electronics Project

Soldering iron

The best type is one powered by mains electricity (230V), it should have a heatproof cable
for safety. The iron's power rating should be 15 to 25W and it should be fitted with a small
bit of 2 to 3mm diameter.

Other types of soldering iron

Low voltage soldering irons are available, but their extra safety is undermined if you have a
mains lead to their power supply! Temperature controlled irons are excellent for frequent use,
but not worth the extra expense if you are a beginner. Gas-powered irons are designed for use
where no mains supply is available and are not suitable for everyday use. Pistol shaped solder
guns are far too powerful and cumbersome for normal electronics use.

Soldering iron stand

18/20
You must have a safe place to put the iron when you are not holding it. The stand should
include a sponge which can be dampened for cleaning the tip of the iron.

Desoldering pump (solder sucker)

A tool for removing solder when

desoldering a joint to correct a mistake or
replace a component.

Reel of solder

The best size for electronics is 22swg (swg = standard wire gauge).

Side cutters

For trimming component leads close to the circuit board.

Wire strippers

Most designs include a cutter as well, but they are not

suitable for trimming component leads.

Small pliers

Usually called 'snipe nose' pliers, these are for bending

component leads etc. If you put a strong rubber band
across the handles the pliers make a convenient holder for
parts such as switches while you solder the contacts.

Small flat-blade screwdriver

For scraping away excess flux and dirt between tracks, as well as driving screws!

19/20
Reference:
David L. Jones, 2004, “PCB Design Tutorial”,
http://alternatezone.com/electronics/files/PCBDesignTutorialRevA.pdf

http://www.computronics.com.au/kinsten/
http://www.ele.tut.fi/~telok/MakePCBs/
http://www.kd7lmo.net/tech_pcb.html
http://shop.eecs.ku.edu/solder.html
http://www.kpsec.freeuk.com/tools.htm

20/20