Scribd
Upload
97 views5 pages

#Include #Define ON 0 #Define OFF 1

The document describes an Arduino sketch that controls 8 relays via Bluetooth. It defines constants for the relay pins and EEPROM addresses. In setup(), it initializes serial communication, sets the relay pins as outputs, and reads the last known relay states from EEPROM. In loop(), it calls the bluetooth() function. bluetooth() checks for serial input, and if received, will turn individual relays on or off and update EEPROM based on the input character, printing status messages.

Uploaded by

raven99
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
97 views5 pages

#Include #Define ON 0 #Define OFF 1

The document describes an Arduino sketch that controls 8 relays via Bluetooth. It defines constants for the relay pins and EEPROM addresses. In setup(), it initializes serial communication, sets the relay pins as outputs, and reads the last known relay states from EEPROM. In loop(), it calls the bluetooth() function. bluetooth() checks for serial input, and if received, will turn individual relays on or off and update EEPROM based on the input character, printing status messages.

Uploaded by

raven99
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 5

#include <EEPROM.

h>
#define ON 0
#define OFF 1

const int relay1 = 2;


const int relay2 = 3;
const int relay3 = 4;
const int relay4 = 5;
const int relay5 = 6;
const int relay6 = 7;
const int relay7 = 8;
const int relay8 = 9;
byte State1 = 1;
byte State2 = 1;
byte State3 = 1;
byte State4 = 1;
byte State5 = 1;
byte State6 = 1;
byte State7 = 1;
byte State8 = 1;
char input;

void setup() {
// put your setup code here, to run once:
Serial.begin(9600);
Serial.println(F("Control 8 Channel relay via Bluetooth"));

pinMode(relay1,OUTPUT);digitalWrite (relay1,OFF);
pinMode(relay2,OUTPUT);digitalWrite (relay2,OFF);
pinMode(relay3,OUTPUT);digitalWrite (relay3,OFF);
pinMode(relay4,OUTPUT);digitalWrite (relay4,OFF);
pinMode(relay5,OUTPUT);digitalWrite (relay5,OFF);
pinMode(relay6,OUTPUT);digitalWrite (relay6,OFF);
pinMode(relay7,OUTPUT);digitalWrite (relay7,OFF);
pinMode(relay8,OUTPUT);digitalWrite (relay8,OFF);

ReadEEPROM ();

void loop() {
// put your main code here, to run repeatedly:
bluetooth();
}

void bluetooth() {
if (Serial.available()>0)
{
input= Serial.read();

if (input == 'A') {
digitalWrite (relay1,ON);
EEPROM.write(1, 0);
Serial.println("relay 1 ON by Bluetooth");}
if (input == 'a') {
digitalWrite (relay1,OFF);
EEPROM.write(1, 1);
Serial.println("relay 1 OFF by Bluetooth");}

if (input == 'B') {
digitalWrite (relay2,ON);
EEPROM.write(2, 0);
Serial.println("relay 2 ON by Bluetooth");}
if (input == 'b') {
digitalWrite (relay2,OFF);
EEPROM.write(2, 1);
Serial.println("relay 2 OFF by Bluetooth");}

if (input == 'C') {
digitalWrite (relay3,ON);
EEPROM.write(3, 0);
Serial.println("relay 3 ON by Bluetooth");}
if (input == 'c') {
digitalWrite (relay3,OFF);
EEPROM.write(3, 1);
Serial.println("relay 3 OFF by Bluetooth");}

if (input == 'D') {
digitalWrite (relay4,ON);
EEPROM.write(4, 0);
Serial.println("relay 4 ON by Bluetooth");}
if (input == 'd') {
digitalWrite (relay4,OFF);
EEPROM.write(4, 1);
Serial.println("relay 4 OFF by Bluetooth");}

if (input == 'E') {
digitalWrite (relay5,ON);
EEPROM.write(5, 0);
Serial.println("relay 5 ON by Bluetooth");}
if (input == 'e') {
digitalWrite (relay5,OFF);
EEPROM.write(5, 1);
Serial.println("relay 5 OFF by Bluetooth");}

if (input == 'F') {
digitalWrite (relay6,ON);
EEPROM.write(6, 0);
Serial.println("relay 6 ON by Bluetooth");}
if (input == 'f') {
digitalWrite (relay6,OFF);
EEPROM.write(6, 1);
Serial.println("relay 6 OFF by Bluetooth");}

if (input == 'G') {
digitalWrite (relay7,ON);
EEPROM.write(7, 0);
Serial.println("relay 7 ON by Bluetooth");}
if (input == 'g') {
digitalWrite (relay7,OFF);
EEPROM.write(7, 1);
Serial.println("relay 7 OFF by Bluetooth");}

if (input == 'H') {
digitalWrite (relay8,ON);
EEPROM.write(8, 0);
Serial.println("relay 8 ON by Bluetooth");}
if (input == 'h') {
digitalWrite (relay8,OFF);
EEPROM.write(8, 1);
Serial.println("relay 8 OFF by Bluetooth");}

}
}

void ReadEEPROM (){


State1 = EEPROM.read(1);
State2 = EEPROM.read(2);
State3 = EEPROM.read(3);
State4 = EEPROM.read(4);
State5 = EEPROM.read(5);
State6 = EEPROM.read(6);
State7 = EEPROM.read(7);
State8 = EEPROM.read(8);
digitalWrite(relay1,State1);
Serial.print(F("Posisi Terakhir relay1 = "));
if(State1==0){Serial.println("ON");} else {Serial.println("OFF");}

digitalWrite(relay2,State2);
Serial.print(F("Posisi Terakhir relay2 = "));
if(State2==0){Serial.println("ON");} else {Serial.println("OFF");}

digitalWrite(relay3,State3);
Serial.print(F("Posisi Terakhir relay3 = "));
if(State3==0){Serial.println("ON");} else {Serial.println("OFF");}

digitalWrite(relay4,State4);
Serial.print(F("Posisi Terakhir relay4 = "));
if(State4==0){Serial.println("ON");} else {Serial.println("OFF");}

digitalWrite(relay5,State5);
Serial.print(F("Posisi Terakhir relay5 = "));
if(State5==0){Serial.println("ON");} else {Serial.println("OFF");}

digitalWrite(relay6,State6);
Serial.print(F("Posisi Terakhir relay6 = "));
if(State6==0){Serial.println("ON");} else {Serial.println("OFF");}

digitalWrite(relay7,State7);
Serial.print(F("Posisi Terakhir relay7 = "));
if(State7==0){Serial.println("ON");} else {Serial.println("OFF");}

digitalWrite(relay8,State8);
Serial.print(F("Posisi Terakhir relay8 = "));
if(State8==0){Serial.println("ON");} else {Serial.println("OFF");}
}
void relayON (uint8_t r) {
digitalWrite (r+1,ON);
EEPROM.write(r, 1);
Serial.print("Relay ");
Serial.print(r);
Serial.println(" ON by Bluetooth");
}

void relayOFF (uint8_t r) {


digitalWrite (r+1,OFF);
EEPROM.write(r, 0);
Serial.print("Relay ");
Serial.print(r);
Serial.println(" OFF by Bluetooth");
}

You might also like