AC Motors Asynchronous Servomotors: Operating Instructions

Edition
AC Motors
Asynchronous Servomotors 10/2001
Operating Instructions
1052 7613 / EN
SEW-EURODRIVE
Contents
1 Important Notes................................................................................................. 4
2 Safety Notes ...................................................................................................... 5
3 Motor Design ..................................................................................................... 6

3.1 Design principle of the AC motor .............................................................. 6
3.2 Nameplate, unit designation ..................................................................... 7
4 Mechanical Installation..................................................................................... 9
4.1 Before you begin....................................................................................... 9
4.2 Preliminary work ....................................................................................... 9
4.3 Installing the motor.................................................................................. 10
4.4 Installation tolerances ............................................................................. 11
5 Electrical Installation ...................................................................................... 12

5.1 Wiring notes ............................................................................................ 12
5.2 Special aspects for operation with a frequency inverter ......................... 12
5.3 Special aspects of operation of single-phase motors ............................. 12
5.4 Special aspects of torque motors and low-speed motors ....................... 13
5.5 Replacement of cable screw fitting threads ............................................ 13
5.6 Special aspects in switching operation ................................................... 14
5.7 Connecting the motor.............................................................................. 14
5.8 Preparation for connecting motor size 63 – knockout............................. 15
5.9 Connecting the DT56...+/BMG motor...................................................... 15
5.10 The ET56 single-phase design ............................................................... 16
5.11 Connecting the motor via IS plug connector ........................................... 16
5.12 Connecting motor via ASA1/ASD1 and AMA1/AMD1 plug connectors .. 20
5.13 Connecting the brake.............................................................................. 20
5.14 Additional equipment .............................................................................. 21
6 Startup.............................................................................................................. 23
I 6.1 Prerequisites for startup.......................................................................... 23
0
6.2 Altering the blocking direction on motors with a backstop ...................... 24
7 Operation and Service .................................................................................... 25

7.1 Motor problems ....................................................................................... 25
7.2 Brake problems....................................................................................... 26
7.3 Problems when operating with a frequency inverter ............................... 26
8 Inspection and Maintenance .......................................................................... 27

8.1 Inspection and maintenance periods ...................................................... 27
8.2 Preliminary work for motor and brake maintenance ............................... 28
8.3 Inspection and maintenance work on the motor ..................................... 31
8.4 Inspection and maintenance of brake BMG02........................................ 33
8.5 Inspection and maintenance of brake BR03 ........................................... 34
8.6 Inspection and maintenance of brake BMG 05-8, BM 15 - 62 ................ 38
9 Technical Data................................................................................................. 43
kVA n 9.1 Work done until maintenance, braking torques of brake BMG02 ........... 43
f
i 9.2 Details for ordering BMG02 spares........................................................ 43
P Hz
9.3 Work done, working air gap, braking torques of brake BR03,
BMG 05-8................................................................................................ 44
9.4 Work done, working air gap, braking torques of brake BM 15 - 62......... 45
9.5 Operating currents .................................................................................. 46
9.6 Permitted ball bearing types ................................................................... 49
9.7 Lubricant table for anti-friction bearings of SEW motors......................... 49
Addresses........................................................................................................ 50
Operating Instructions – AC Motors, Asynchronous Servomotors 3

1 Important Notes
1 Important Notes
Safety and Always follow the safety and warning instructions contained in this publication!
warning
instructions
Electrical hazard
Possible consequences: Severe or fatal injuries.
Hazard
Possible consequences: Severe or fatal injuries.
Hazardous situation
Possible consequences: Slight or minor injuries.
Harmful situation
Possible consequences: Damage to the unit and the environment.
Tips and information
A requirement of fault-free operation and fulfillment of any rights to claim under

guarantee is that the information in the operating instructions is adhered to.
Consequently, read the operating instructions before you start working with the unit!
The operating instructions contain important information about servicing; as a result,
they should be kept in the vicinity of the unit.
Waste disposal This product consists of

• Iron
• Aluminum
• Copper
• Plastic
• Electronics components
Please dispose of the parts in accordance with the applicable regulations.
Modifications to the 03/2001 edition are indicated by a gray bar in the margin.
4 Operating Instructions – AC Motors, Asynchronous Servomotors

Safety Notes 2
2 Safety Notes
Preliminary The following safety notes are concerned primarily with the use of geared motors. If
notes using geared motors, please also refer to the safety notes for gear units in the
corresponding operating instructions.
Please also take account of the supplementary safety notes in the individual
sections of these operating instructions.
General During and after operation, motors and geared motors have live and moving parts which
information may possibly also have hot surfaces.
All work related to transport, storage, assembly / mounting, connection, startup,

maintenance and repair may only be carried out by trained personnel observing
• the corresponding detailed operating instructions and wiring diagrams,
• the warning and safety signs on the motor/geared motor,
• the specific regulations and requirements for the system and
• national/regional regulations governing safety and prevention of accidents.
Severe injuries and damage to property may result from

• incorrect use
• incorrect installation or operation,
• removal of required protective covers or the housing when this is not permitted.
Designated use These electric motors are intended for industrial systems. They comply with the
applicable standards and regulations and meet the requirements of the Low Voltage
Directive 73/23/EEC.
Technical data and information about the conditions permitted at the location where the
unit is being used can be found on the nameplate and in these operating instructions (→
Sec. 9 "Technical Data").
It is essential for this specified information to be observed!
Transport and Please inspect the delivery immediately upon arrival for any transport damage.
storage Inform the transport company immediately of any damage which has occurred. It
may be necessary to preclude startup.
Screw-on eyebolts must be drawn on and tightened. They are approved to carry only
the weight of the motor/geared motor; additional loads may not be attached.
The integrated eye bolts comply with DIN 580. The loads and directives specified
in this standard must be complied with. If two eybolts are provided on the geared
motor, then both eyebolts must be used for transport. The angle of the hoisting
gear and attachments must not exceed 45° according to DIN 580.
Where required, use appropriate and adequately sized means of transport. Remove
transport safety devices before startup.
Assembly / Observe the notes in the section on "Mechanical Installation"!

Mounting
Inspections / Observe the notes in the section on "Inspection / Maintenance"!

Maintenance

3 Design principle of the AC motor
3 Motor Design
The following illustration is a representation of the principle design of the motors. It is
intended to serve as a support for the identification of the parts when referring to the
Spare Parts Lists. Some differences may occur depending on the motor size and design.
3.1 Design principle of the AC motor
31 20 44 41
1
3
12
11
10
9 7
106
107 13
2
100
101 22
103 35
32
36
37
42
116
118
117
119
111
16 112
123
135
134
130 115
113
129 131
132
02969AXX
Legend
1 Rotor, cpl. 31 Key 107 Oil flinger 131 Gasket
2 Circlip 32 Circlip 111 Gasket 132 Terminal box cover
3 Key 35 Fan guard 112 Terminal box lower part 134 Screw plug
7 Flanged end shield 36 Fan 113 Slotted cheese head screw 135 Sealing washer
9 Screw plug 37 V-ring 115 Terminal board
10 Circlip 41 Equalizing ring 116 Terminal yoke
11 Grooved ball bearing 42 Non drive-end bearing shield 117 Hex head screw
12 Circlip 44 Grooved ball bearing 118 Lock washer
13 Hex head screw (tie rod) 100 Hex nut 119 Slotted cheese head screw
16 Stator, cpl. 101 Lock washer 123 Hex head screw
20 Nilos ring 103 Stud 129 Screw plug
22 Hex head screw 106 Oil seal 130 Gasket

Nameplate, unit designation 3
3.2 Nameplate, unit designation

Nameplate
Example: Brake motor DFV 160 M4 /BM
DFV 160 M 4 /BM

01.3001234568.0001.00 B5
11 S1 0.83
220 - 240 ∆ / 380 - 415 Y 39.0 / 22.5
240 -266 ∆ / 415 - 460 Y 35.5 / 20.5
1440 / 1740 55 F
230 AC 150 BGE1.5
109
03214AXX
Type designation
Example: AC (brake)motors DR/DT/
DT 90S4 / BMG / TF / IS
Motor option IS connector
Motor option TF sensor
Motor option brake
Size 90S and 4-pole
Foot-mounted motor
DFV 132M2 / BM / TF / AMA1 / EV1T

Motor option 5 V TTL incremental encoder
Motor option AMA1 connector
Motor option brake
Size 132M and 2-pole
Flange-mounted motor
DV 112 M4 F / RS / Z / C
Motor option protection cover

Motor option Z additional flywheel mass
Motor option backstop
DV..F = Foot/flange-mounted motor
05157AEN
Example: Fabrication number
01. 301234568. 0001. 00

Manufacturer’s last two year number digits
Serial number (4 digits)
Order number (10 digits)
Sales organization
05156AEN

3 Nameplate, unit designation
Nameplate
Example: Servo brake motor CT90L4 / BMG / TF
CT90L4 BMG TF
01.3410069302.0001.00
30.5
10.5 3000
103 345 7.9
B5 28 54 F
230~ 20 BGE 1.5
50473AXX
Type designation
Example: Servo (brake) motor CT/CV
CT 90L4 / BMG / TF / AV1Y

Motor option absolute encoder
Motor option brake
Size 90L and 4-pole
Foot-mounted motor
CFV 132M4 / BM / TF / EV1S

Motor option incremental encoder
Motor option brake
Flange-mounted motor
CV 112M4 F / C / ES2T
5 V TTL incremental encoder option

Motor option protection cover
CV..F = Foot/flange-mounted motor
05158AEN
Example: Fabrication number
01. 3410069302. 0001. 00

Last two digits of year of manufacture
Serial part number 4 digits
Order number (10 digits)
Sales organization
05161AEN

Before you begin 4
4 Mechanical Installation
It is essential to comply with the safety notes in section 2 during installation!
4.1 Before you begin

The drive may • the entries on the nameplate of the drive and/or the output voltage of the frequency
only be installed inverter match the voltage supply system,
if • the drive is undamaged (no damage caused by transport or storage) and
• it is certain that the following requirements have been fulfilled:
– Ambient temperature between –25 °C and +40 °C1
– No oil, acid, gas, vapors, radiation, etc.
– Installation altitude max. 1000 m above sea level
– Note the restrictions for encoders (SEW Encoder Systems manual)
– Special versions: drive configured in accordance with the ambient conditions
4.2 Preliminary work

Motor shaft extensions must be cleansed thoroughly to remove anti-corrosion agents,
dirt, dust and similar substances (use a commercially available cleaning solvent). Do not
allow the solvent to come into contact with the bearing or the shaft seals - this could
cause damage to material!
Long-term • Please take note of the reduced grease utilization period of the ball bearings after
storage storage periods exceeding one year.
• Check whether the motor has absorbed moisture as a result of being stored for a
long period. To do this, measure insulation resistance (measuring voltage 500 V).
The insulation resistance (→ graph below) varies greatly depending on the tem-
perature! The motor must be dried if the insulation resistance is not adequate.
[M ]
100
10
0,1
0 20 40 60 80
[°C]
01731AXX
1. Minimum temperature for motors with backstop: –15 °C, note that the temperature range
of the gear unit may also be restricted (→ Gear unit operating instructions)

4 Installing the motor
Drying the motor Heat up the motor

• with hot air or
• using an isolation transformer
– Connect the windings in series (→ following illustration)
– Auxiliary AC voltage supply max. 10 % of the rated voltage with
max. 20 % of the rated current
Transformer
01730AEN
The drying process must be ended when the minimum insulation resistance has been
attained.
Check the terminal box to see whether
• the inside is clean and dry,
• the connections and fixing parts are free from corrosion,
• the joint seals are OK,
• the cable screw fittings are sound, otherwise clean or replace them.
4.3 Installing the motor

The motor or geared motor may only be mounted or installed in the specified mounting
position on a level and torsionally rigid support structure which is not subject to shocks.
Carefully align the motor and the driven machine, to avoid placing any unacceptable
strain on the output shafts (observe permissible overhung load and axial thrust data!).
Do not butt or hammer the shaft extension.
Use an appropriate cover to protect motors in vertical mounting positions from
objects or fluids entering! (Protection cowl C)
Ensure an unobstructed cooling air supply and that air heated by other apparatus cannot
be drawn in or reused.
Balance components for subsequent mounting on the shaft with a half key (motor shafts
are balanced with a half key).
Any condensation drain holes will be sealed by plastic plugs and should only be
opened when necessary; open condensation drain holes are not permissible, as
this would invalidate higher classes of enclosure.
Brake motors with manual brake release:
Screw in either the hand lever (with self-reengaging manual brake release) or the
setscrew (with locked manual brake release).
Important encoder information:
Foot-mounted motors CT/DT71, CT/DT90, CV/DV132M, CV/DV160L must be mounted
on supports because the radius of the cover is greater than the shaft height.

Installation tolerances 4
Installation in If possible, arrange the terminal box so the cable entries are pointing downwards.
damp areas or in Coat the threads of cable screw fittings and blind plugs with sealant and tighten them
the open well – then coat them again.
Seal the cable entry well.
Thoroughly clean the sealing surfaces of terminal boxes and terminal box covers prior
to reassembly; gaskets must be glued in on one side. Fit new gaskets to replace brittle
ones!
Restore the anticorrosive coating, if necessary.
Check the enclosure.
4.4 Installation tolerances

Shaft extensions Flanges
Diametric tolerance in accordance with DIN 748 Centering shoulder tolerance in accordance with DIN
• ISO k6 at Ø ≤ 50 mm 42948
• ISO m6 at Ø > 50 mm • ISO j6 at Ø ≤ 230 mm
(Center bore in accordance with DIN 332, shape DR) • ISO h6 at Ø > 230 mm

5 Wiring notes
5 Electrical Installation
It is essential to comply with the safety notes in Section 2 during installation!
Switch contacts in utilization category AC-3 to EN 60947-4-1 must be used for
switching the motor and the brake.
5.1 Wiring notes

Protection Do not route brake cables alongside switched-mode power cables, since otherwise
against there is a risk of disrupting brake controllers.
interference from
brake control Switched-mode power cables include, in particular:
systems
– Output cables from frequency and servo controllers, converters, soft start units
and brake units
– Connecting harnesses to braking resistors, etc.
Protection To provide protection against interference from SEW motor protection devices
against (temperature sensors TF, winding thermostats TH):
interference from – Route separately shielded feeder cables together with switched-mode power
motor protection lines in one cable
devices – Do not route unshielded feeder cables together with switched-mode power lines
in one cable
5.2 Special aspects for operation with a frequency inverter

Observe the wiring instructions issued by the inverter manufacturer when motors are
powered by inverters. It is essential to adhere to the frequency inverter operating
instructions.
5.3 Special aspects of operation of single-phase motors

Please note that SEW single-phase motors (with the exception of ET56L4 → Section
"ET56 Single-phase motor design") are supplied without accessory equipment such as
capacitors, starting relays or centrifugal switches. Any parts you need must be obtained
from your dealer and connected according to the corresponding instructions and wiring
diagrams.

Special aspects of torque motors and low-speed motors 5
5.4 Special aspects of torque motors and low-speed motors

Due to the design of torque motors and low-speed motors, very high induction voltages
may be generated when they are switched off. We therefore recommend connecting a
varistor to provide protection. The size of the varistors depends, among other factors,
on the starting frequency – refer to project planning!
U U U
U1 V1 W1
01732CXX
5.5 Replacement of cable screw fitting threads

On 1/1/2000, the DIN 46320 standard applicable in Germany for Pg glands was replaced
by European standard EN 50262 for metric cable screw fittings. Terminal boxes of SEW
AC motors and AC brake motors are configured with metric threaded holes according to
EN 50262 as a standard.
M..x1.5
Pg..
03132AXX
Cable screw fitting

Motor size
Pg Metric
DT56 - 2 × M20×1.5, 2 × M12×1.5
DFR63 - 2 × M20×1.5, 2 × M16×1.5
DT71 – DT90 1 × Pg16, 1 × Pg11 1 × M25×1.5, 1 × M16×1.5
DV100 – DV132S 1 × Pg21, 1 × Pg11 1 × M32×1.5, 1 × M16×1.5
DT71/BMG – DT90/BMG 2 × Pg16, 1 × Pg11 2 × M25×1.5, 1 × M16×1.5
DV100/BMG – DV132S/BMG 2 × Pg21, 1 × Pg11 2 × M32×1.5, 1 × M16×1.5
DV132M – DV132ML + /BM 2 × Pg21, 2 × Pg11 2 × M32×1.5, 2 × M16×1.5
DV160M – DV180L + /BM 2 × Pg29, 2 × Pg11 2 × M40×1.5, 2 × M16×1.5
DV200 – DV225 + /BM 2 × Pg36, 2 × Pg11 2 × M50×1.5, 2 × M16×1.5

5 Special aspects in switching operation
5.6 Special aspects in switching operation

When the motors are used in switching operation, any possible malfunctions of the
switchgear must be excluded by appropriate wiring. According to EN 60204 (electrical
equipment of machines), motor windings must have interference suppression in order
to protect the numerical or programmable logic controllers. Since it is primarily switching
operations which lead to disruptions, we recommend installing protective circuitry on the
switching devices.
5.7 Connecting the motor

In case of operation with electronic control units, it is essential to adhere to the
corresponding operating instructions/wiring diagrams!
Connecting the • According to circuit diagram (enclosed)

motor via • Check the cross sections of cables
terminal boxes • Arrange terminal links correctly
• Fasten connections and protective earth conductors firmly
• In terminal boxes: Check winding connections and tighten them if necessary
Small connection Please note: In the case of motor sizes 71 - 132S, the small connection accessories
accessories (connection nuts for feeder cables, terminal links, the lock washer and the washers) are
supplied in a bag. Install the parts as demonstrated by the following illustration.
1 5
6
2
3
7
4 8
01960BXX
1 Terminal stud
2 Lock washer
03131AXX
3 Terminal washer
4 Motor terminal lead
5 Top nut
6 Washer
7 External connection
8 Bottom nut

Preparation for connecting motor size 63 – knockout 5
5.8 Preparation for connecting motor size 63 – knockout

Important: Wear safety glasses – danger of injury from fragments!
• Put on the terminal box cover and fasten with screws.
• Determine which cable entries to open.
• Open the cable entries
– with a chisel or similar (hold at an angle)
– tap lightly with a hammer
01733AXX
Caution - Do not knock through to the inside of the terminal box!

• Open the terminal box, remove the knockout cover if it has broken off.
• Secure the cable screw fittings with the supplied lock nuts.
5.9 Connecting the DT56...+/BMG motor

The motor is wired with three connections in Star in the winding overhang. The supply
system leads (L1, L2, L3) are connected in the terminal (1) to a terminal block with cage
clamps (2). The BMG02 brake is controlled via the BG1.2 brake rectifier (3).
Alternatively, brake control is also possible from the switch cabinet with the rectifiers
from the BM series.
TF TF U V W
04861AXX

5 The ET56 single-phase design
5.10 The ET56 single-phase design

The ET56 single-phase motor is deliverd with the running capacitor installed and con-
nected:
1~230 V, 50 Hz CB = 4 µF
1~230 V, 60 Hz CB = 4 µF
1~110 V, 60 Hz CB = 20 µF
A full-load startup can only be prevented by employment of the running capacitor!

The single-phase motor cannot be combined with the TF.
5.11 Connecting the motor via IS plug connector
03075AXX
The IS plug connector is supplied from the factory with its base fully wired, including
additional features such as a brake rectifier. The upper section of the IS connection is
included in the scope of delivery and must be connected as shown in the circuit diagram.
The IS plug connection has CSA approval up to 600 V. (Note for application according
to CSA regulations: Tighten the M3 terminal screws to a torque of 0.5 Nm! Note the line
cross sections according to American Wire Gauge (AWG) as shown in the following
table.
Cable cross Make sure the type of line corresponds to the applicable regulations. The rated currents
sections are specified on the motor nameplate.
Without variable With variable Link cable Double assignment
terminal link terminal link (motor and brake/SR)
0.25 - 4.0 mm2 0.25 - 2.5 mm2 max. 1.5 mm2 max. 1 x 2.5 and 1 x 1.5mm2
23 - 12 # AWG 23 - 14 # AWG max. 16 # AWG max. 1 x 14 # and 1 x 16 # AWG

Connecting the motor via IS plug connector 5
Wiring the upper • Remove screws from housing cover

section of the – remove the cover
plug connector
• Loosen screws from upper section of plug connector
– remove the upper section of the plug connection from the cover
• Strip the insulation off the connection lead
– strip about 9 mm insulation off the connecting leads
• Pass the cable through the cable screw fitting
Wiring up as • Connect the lines as shown in the circuit diagram

shown in circuit – tighten clamping screws carefully!
diagram DT82,
• Install the plug connection (→ Section "Installing plug connection" )
DT83
Wiring up as For V/∆ startup:

shown in circuit • Connection with 6 lines
diagram DT81,
– tighten the clamping screws carefully!
DT83
– motor contactors in the switch cabinet
• Install the plug connection (→ Section "Installing plug connection")
For V or ∆ operation:
• Connection according to circuit diagram
• Install the variable terminal link according to the required motor operation (V or ∆, )
as demonstrated in the following illustrations
• Install the plug connection ( → Section "Installing plug connection")
01734AXX 01735AXX

5 Connecting the motor via IS plug connector
Brake control For V operation:

system BSR – On the V side of the variable terminal link:
preparing the remove only bright metal pin of the marked prong horizontally – touch guard!
variable terminal
link
50429AXX
For ∆ operation:
On the ∆ side of the variable terminal link:
remove the two (2) marked prongs completely horizontally.
01737AXX
Wiring up as • At terminal point for double assignment:

shown in circuit - Connect the link cable.
diagram DT 81 for • When operation is as required:
V- or ∆ operation - Insert the link cable in the variable terminal link.
with double • Install the variable terminal link.
terminal
• At terminal point for double assignment:
assignment
- Connect the motor lead above the variable terminal link.
• Connect the other lines as shown in the circuit diagram.
• Install the plug connection (→ Section "Installing the plug connector).
01738AXX

Connecting the motor via IS plug connector 5
Installing the plug The housing cover of the IS plug connector can be screwed onto the lower section of
connector the plug connector depending on the required position of the cable lead. The upper
section of the plug connector must first be installed in the housing cover so it will match
the position of the lower plug connector section:
• Define the required mounting position.
• Install upper section of the plug connector into the housing cover according to the
mounting position.
• Close the plug connector.
• Tighten the cable screw fitting.
01739AXX
Mounting position of upper section of plug connector on housing cover
01740AXX

5 Connecting motor via ASA1/ASD1 and AMA1/AMD1 plug connectors
5.12 Connecting motor via ASA1/ASD1 and AMA1/AMD1 plug connectors
1 2
05107AXX
The ASD1 type with single clip closure corresponds to the DESINA regulation issued by
the Association of German Machine Tool Manufacturers (VDW).
The bottom part of the ASA1 / ASD1 or AMA1 / AMD1 is supplied from the factory with
®
its base fully wired, including additional features such as a brake rectifier.
The customer is responsible for obtaining the upper section of the connector
from the dealer and connecting it in accordance with the wiring diagrams
(supplied with the motor).
5.13 Connecting the brake

The brake is released electrically. The brake is applied mechanically when the voltage
is switched off.
Comply with the applicable regulations issued by the relevant employer’s liability
insurance association regarding phase failure protection and the associated
circuit/circuit modification!
• Connect the brake according to the circuit diagram supplied with the brake.
• Note: In view of the DC voltage to be switched and the high level of current load, it
is essential to use either special brake contactors or AC contactors with contacts in
utilization category AC-3 to EN 60947-4-1.
• For version with manual brake release, screw in
– hand lever (for manually disengaging brake)
– or manual brake release screw (for fixing brake in the disengaged position)
Connecting the The DC disk brake is powered from a brake control system with protective circuitry. This
brake control is accommodated in the terminal box / IC lower part or must be installed in the switch
system cabinet. (Pay attention to the wiring notes → Sec. 5.1.)
• Check the line cross sections – braking currents (→ Section "Technical Data")
• Connect the brake control system according to the circuit diagram supplied with
the brake
• For motors with thermal classification H: Install the brake rectifier in a switch
cabinet!

Additional equipment 5
5.14 Additional equipment

Connect supplied additional equipment according to the wiring diagrams included.
TF temperature sensor
Do not apply any voltage!
The positive temperature coefficient (PTC) thermistors comply with DIN 44082.
Resistance measurement (measuring instrument with V ≤ 2.5 V or I < 1 mA).
• Normal measured values: 20 – 500 Ω, thermal resistance > 4000 Ω.
• Measured values pole-changing with separate winding: 40 – 1000 Ω,
thermal resistance > 4000 Ω.
TH winding thermostats
The thermostats are connected in series as standard and open when the permitted
winding temperature is exceeded. They can be connected in the drive monitoring loop.
VAC VDC
Voltage [V] 250 400 60 24
Current (cos ϕ = 1.0) [A] 2.5 0.75 1.0 1.6
Current (cos ϕ = 0.6) [A] 1.6 0.5
Contact resistance max. 1 Ohm at 5 V = / 1 mA
Forced cooling fan

Motor size 71-132S
VR system VS system
• 24 VDC ± 20 % • 1 x 230 VAC, 50 Hz
• Plug connector • Connection in separate terminal box
• Maximum connection cross section • Maximum connection cross section
3 x 1 mm² 3 x 1.5 mm²
• Cable screw fitting Pg7 • Cable screw fitting M16 x 1.5
with inside diameter 7 mm
Motor size 132M-225 V system

• 3 x 400 VAC, 50 Hz
• Connection in separate terminal box
• Maximum connection cross section 4 x 1.5 mm²
• Cable screw fitting M16 x 1.5
A transformer may be present in the VS system in order to adapt to a voltage other than
the standard. VS and V systems are also available for 60 Hz.
Please refer to the VS or V circuit diagram for information about connecting the VS and
V systems (order no: 0975 8385).

5 Additional equipment
Overview of SEW
encoder systems For SEW Type of Specifi-
Encoder Shaft Supply Signal
motor encoder cation
1)
ES1T 5 VDC
5 VDC TTL/RS-422
regulated
ES1S2) CT/DT/CV/ 1 VSS sin/cos
DV71 – 100
ES1R 24 VDC 5 VDC TTL/RS-422
ES1C Spread 24 VDC HTL
ES2T1) shaft 5 VDC
5 VDC TTL/RS-422
regulated
ES2S 2) CV/DV 1 VSS sin/cos
Encoder -
112 – 132S
ES2R 24 VDC 5 VDC TTL/RS-422
ES2C 24 VDC HTL
EV1T1) 5 VDC
5 VDC TTL/RS-422
regulated
EV1S 2) CT/CV71 – 200 1 VSS sin/cos
Solid shaft
DT/DV71 – 225
EV1R 24 VDC 5 VDC TTL/RS-422
EV1C 24 VDC HTL
NV11 A track 1 pulse/revolution,
NV21 normally open
A+B track contact
NV12 A track 2 pulses/
NV22 revolution,
DT/DV Proximity
Solid shaft A+B track 24 VDC normally open
71 – 132S sensors
contact
NV16 A track 6 pulses/
NV26 revolution,
A+B track normally open
contact
AV1Y MSSI interface
15/24 VDC
and 1 VSS sin/cos
CT/CV71 – 200 Absolute
AV1H Solid shaft - HIPERFACE
DT/DV71 – 225 encoder
7/12 VDC interface and
1 VSS sin/cos
1. recommended encoder for operation with MOVITRAC® 31C

2. recommended encoder for operation with MOVIDRIVE®
• Refer to the following wiring diagrams for information about connecting ES1./ES2./
EV1. encoders and AV1Y and AV1H absolute encoders:
– Wiring diagram ES1./ES2. or EV1. encoder: Order number 0918 6832
– Wiring diagram AV1Y absolute encoder: Order number 0918 6808
– Wiring diagram AV1H absolute encoder: Order number 1052 9705
Encoder Always follow the operating instructions for the relevant inverter when connecting the
connection encoders to the inverters!
• Max. line length (inverter – encoder):
– 100 m with a cable capacitance ≤ 120 nF/km
• Core cross section: 0.20 – 0.5 mm2
• Use a shielded cable with twisted pairs of insulated conductors (exception: cable for
HTL sensor) and connect the shield over a large surface area at both ends:
– to the encoder in the cable screw fitting or in the encoder plug
– to the inverter on the electronics shield clamp or to the housing of the sub D plug
• Route the encoder cables separately from the power cables, maintaining a gap of at
least 200 mm.

I
Startup 6
0
6 Startup
6.1 Prerequisites for startup
During startup it is essential to comply with the safety notes in Section 2.
Before startup, • the drive is undamaged and not blocked,

make sure that • the measures stipulated in Sec. 4.2 ”Preliminary work” are performed after lengthy
storage,
• all connections have been made properly,
• the direction of rotation of the motor/geared motor is correct
(motor rotating clockwise: U, V, W to L1, L2, L3),
• all protective covers have been fitted correctly,
• all motor protection equipment is active and set for the rated current of the motor,
• in the case of hoist drives, the self-reengaging manual brake release is used,
• there are no other sources of danger present.
During startup, • the motor is running correctly (no overload, no speed fluctuation, no loud noises,
make sure that etc.),
• the correct braking torque is set according to the specific application (→ Section
"Technical Data"),
if problems occur (→ Section "Operation and Service").
In brake motors with self-reengaging manual brake release, the manual brake
release lever must be removed after startup. A bracket is provided for storing it
on the outside of the motor.

I
6 Startup
0
6.2 Altering the blocking direction on motors with a backstop

9 8 5 3 4 2 1
7 10 6
50447AXX
Dimension X after
installation Motor Dimension X after installation
DT71/80 6.7 mm
DT90/DV100 9.0 mm
DV112/132S 9.0 mm
DV132M-160M 11.0 mm
DV160L-225 11.0 mm
Do not start up the motor in the blocking direction (note the phase angle when
connecting). Note the direction of rotation of the output shaft and the number of stages
when mounting the motor on a gear unit. For testing purposes, the backstop can be
operated once in the blocking direction at half the motor voltage for checking purposes.
1. Isolate the motor from the power supply source, preventing an unintentional
restart.
2. Remove fan guard (1) and fan (2); remove the machine screws (3).
3. Remove V-ring (4) and sealing flange with felt ring (5) (Collect grease for
subsequent use).
4. Remove circlip (6) (not with DT71/80); in additional for DV132M-160M: remove the
equalizing rings (10).
5. Pull the driver (8) and wedge element train (9) completely off via threading bores (7),
turn them by 180° and press them back on.
6. Refill the grease.
7. Important: Do not exert pressure on or hit the wedge element train – possible
material damages!
8. During the press-in operation – shortly before the wedge element enters the locking
collar – slowly turn the rotor shaft by hand in the direction of rotation. This allows the
wedge elements to slide into the locking collar more easily.
9. Fit the remaining parts of the backstop by following,in reverse order, steps 4. to 2.
Note the installation dimension for the V-ring (4).

Motor problems 7
7 Operation and Service

7.1 Motor problems
Problem Possible cause Solution
Motor does not start up Interruption in connecting harness Check connections, correct
Brake does not release → Section "Brake problems"
Fuse blown Fit new fuse
Motor protection has tripped Check motor protection is set correctly,
rectify any fault
Motor protection does not switch, fault in Check motor protection control,
control rectify any fault
Motor does not start or Motor designed for delta connection but Correct circuit
only with difficulty used in star connection
Voltage and frequency deviate markedly Provide better supply system; check cross
from setpoint, at least during switch-on section of connecting harness
Motor does not start in Torque not sufficient in star connection Switch on directly if delta inrush current is not too
star connection, only in great; otherwise use a larger motor or a special
delta connection version (contact SEW)
Contact fault on star delta switch Rectify fault
Incorrect direction of Motor connected incorrectly Swap over two phases
rotation
Motor hums and has high Brake does not release → Section "Brake problems"
current consumption Winding defective Send motor to specialist workshop for repair
Rotor rubbing
Fuses blow or motor Short circuit in line Rectify short circuit
protection trips Short circuit in motor Send motor to specialist workshop for repair
immediately
Lines connected incorrectly Correct circuit
Ground fault on motor Send motor to specialist workshop for repair
Severe speed loss under Overload Perform power measurement, use larger motor or
load reduce load if necessary
Voltage drops Increase cross section of connecting harness
Motor heats up Overload Perform power measurement, use larger motor or
excessively reduce load if necessary
(measure temperature) Inadequate cooling Correct cooling air supply or clear cooling air
passages, retrofit forced cooling fan if necessary
Ambient temperature too high Adhere to permitted temperature range
Use delta connection for motor rather Correct circuit
than star connection as provided for
Loose contact in connecting harness (one Rectify loose contact
phase missing)
Fuse blown Look for, rectify cause (see above), fit new fuse
Supply voltage deviates from rated motor Adapt motor to supply voltage
voltage by more than ± 5 %. A higher
voltage has a particularly unfavorable effect
in motors with a low-speed winding since in
these, the no-load current is already close
to the rated current even when the voltage
is normal.
Rated operating mode (S1 to S10, DIN Adapt rated operating mode of motor to
57530) required operating conditions; if necessary call in
exceeded, e.g. due to excessive a specialist to determine what is the correct drive
Starting frequency
Excessively loud Ball bearing compressed, contaminated or Re-align motor, inspect ball bearing (→ Section
damaged "Permitted ball bearing types"), grease if
necessary (→ Section "Lubricant table for anti-
friction bearings of SEW motors), replace
Vibration of rotating parts Rectify cause, possibly imbalance
Foreign bodies in cooling air passages Clean the cooling air passages

7 Brake problems
7.2 Brake problems

Problem Possible cause Solution
Brake does not release Incorrect voltage on brake control unit Apply correct voltage
Brake control unit failed Fit a new brake control system, check internal
resistance and insulation of brake coil, check
switchgear
Max. permitted working air gap exceeded Measure and set working air gap
because brake lining worn down
Voltage drop along connecting harness Provide for correct connection voltage
> 10 % Check cable cross section
Inadequate cooling, brake overheats Replace type BG brake rectifier with type BGE
Brake coil has interturn fault or Replace complete brake and brake control
short circuit to exposed conductive part system (specialist workshop), check switchgear
Motor does not brake Working air gap not correct Measure and set working air gap
Brake lining worn down Replace entire brake disk
Incorrect braking torque Change the braking torque
(→ Section " Technical data"):
• by the type and number of brake springs
• Brake BMG 05: by installing the same brake
coil body design as in the BMG 1 brake
• Brake BMG 2: by installing the same brake
coil body design as in the BMG 4 brake
BM(G) only: Working air gap so large that Check working air gap
setting nuts come into contact
BR03, BM(G) only: Manual brake release Set the setting nuts correctly
device not set correctly
Brake is applied with Brake is switched on AC voltage Switch on DC and AC voltage sides
time lag side (e.g. BSR); please refer to circuit diagram
Noises in Gearing wear caused by jolting Check project planning
vicinity of brake startup
Pulsating torques due to incorrectly set Check/correct setting of frequency inverter
frequency inverter according to operating instructions
7.3 Problems when operating with a frequency inverter

The symptoms described in the section on "Motor problems" may also occur when the
motor is operated with a frequency inverter. Please refer to the frequency inverter
operating instructions for the significance of the problems which occur and to find
information about rectifying the problems.
If you require assistance from our customer service staff, please state the
following:
• Type and extent of the fault
• Time and peripheral circumstances of the fault
• Presumed cause
• Data on the nameplate

Inspection and maintenance periods 8
8 Inspection and Maintenance

• Only use genuine spare parts in accordance with the valid parts list!
• Always fit a new brake control system at the same time as replacing the brake coil!
• Motors can become very hot during operation – danger of burns!
• Secure hoist drives or lower them (danger of falling).
• Isolate the motor and brake from the supply before starting work, safeguarding them
against unintentional power-up!
8.1 Inspection and maintenance periods

Equipment/components Frequency What to do?
Inspecting the brake:
• If used as a working brake: • Measure and set working air gap
At least every 3000 hours of • brake disc, lining
operation1) • Pressure plate
• Carrier / gearing
Brake BMG02, BR03,
• Pressure rings
BMG 05-8, BM 15- 62
• If used as a holding brake: • Extract the abraded matter
Depending on loading conditions: • Inspect the switch elements and
Every 2 to 4 years 1) replace if necessary (e.g. in case of
burn-out)
Inspect the motor:
• Check ball bearings and change if
Motor necessary
• Change the oil seal
• Clean the cooling air passages
• Every 10 000 hours of operating
• Change the low-viscosity grease in
Motor with backstop
the backstop
• Inspection / maintenance as
Tacho-generator described in the enclosed operating
instructions
• Varies • Touch up or renew the surface/
Drive
(depending on external factors) anticorrosion coating
1) The periods of wear are affected by many factors and may be short.
The machine designer must calculate the required inspection/maintenance intervals individually in
accordance with the project planning documents (e.g. Drive Engineering - Practical
Implementation, Vol. 4).

8 Preliminary work for motor and brake maintenance
8.2 Preliminary work for motor and brake maintenance
Isolate the motor and brake from the supply before starting work, safeguarding
them against unintentional power-up!
Removing the incremental encoder EV1. / absolute encoder AV1H
234 369 220 361
236 233 366 251 232

236 233 366 251 232
03329AXX 50431AXX
Incremental encoder EV1 Absolute encoder AV1H
• Remove the hood cover (361). If a forced cooling fan is fitted, remove it first.
• Remove the screw (366) from the intermediate flange and detach the cover plate
(369).
• Unscrew the clamping hub connection of the coupling.
• Loosen the retaining screws (232) and turn the conical spring washers (251)
outwards.
• Remove the encoder (220) together with the coupling (233).
• Lever off the intermediate flange (236) after removing the screws (234).
Note:
During re-assembly, make sure that the runout of the shaft end is ≤ 0.05 mm.

Preliminary work for motor and brake maintenance 8
Removing the incremental encoder ES1. / ES2.

733 367 220 361
50471AXX
• Remove the hood cover (361).

• Loosen retaining screws on the torque arm (733).
• Loosen retaining screws of cover (220) on back of encoder and remove cover.
• Unscrew the central retaining screw (367) by about 2 – 3 turns and loosen the cone
by tapping lightly on the head of the screw. Then unscrew the retaining screw and
pull off the encoder.
Note:
During re-assembly:
– Apply Noco-Fluid® to the encoder spigot.
– Tighten the central retaining screw (367) to 2.9 Nm.

8 Preliminary work for motor and brake maintenance
Removing proximity sensors NV1. / NV2.
3.5
01114CXX
Important! It is essential for the fan wheel to be stationary!
• Disconnect the plug!

• Pull off the fan guard including NV1. / NV2. Do not tilt as this could cause damage to
the proximity switch.
• If the mounting block has been removed from the fan guard or has come loose, it is
essential to ensure the following during re-assembly:
The switching surface of the proximity switch must be calibrated to a distance of
3.5 mm from the edge of the prismatic block (→ above illustration).

Inspection and maintenance work on the motor 8
8.3 Inspection and maintenance work on the motor

Example: DFT90 motor
10 11 12
9
8
7
6
4
5
3
2
1 15
20
19
18
17
16
14
13
01945AXX
Key
1 Circlip 8 Circlip 15 Hex head screw
2 Oil flinger 9 Rotor 16 V-ring
3 Oil seal 10 Nilos ring 17 Fan
4 Screw plug 11 Ball bearing 18 Circlip
5 Drive end bearing end 12 Equalizing ring 19 Fan guard
shield 13 Stator 20 Housing screw
6 Circlip 14 Non-drive end bearing end
7 Ball bearing shield

8 Inspection and maintenance work on the motor
Procedure Isolate the motor and brake from the supply, safeguarding them against
unintentional power-up!
1. Remove the forced cooling fan and encoder, if fitted (→ Section "Preliminary work
for motor and brake maintenance).
2. Remove the flange cover or fan guard (19) and the fan (17).
3. Remove the hexagon head cap screws (15) from the drive end bearing end shield
(5) and the non-drive end bearing end shield (14), release the stator (13) from the
drive end bearing end shield.
4. Motors with brake BM/BMG:
– Open the terminal box cover, loosen the brake cable from the rectifier.
– Push the non-drive end bearing shield and the brake off the stator and
– carefully lift them off (if necessary, run the brake cable along with trailing wire).
– Pull the stator off by about 3 – 4 cm.
5. Motors with brake BMG02, BR03:
– Remove the complete brake with the releasing lever (on version with manual
brake release).
6. Visual check: Are there traces of gear oil or condensation inside the stator?
– If not, continue with 9.
– If there is condensation, continue with 7.
– If there is gear oil, have the motor repaired by a specialist workshop.
7. If there is condensation inside the stator
– Geared motors: Remove the motor from the gear unit.
– Motors without a gear unit: Remove the drive end flange.
– Remove the rotor (9).
8. Clean the winding, dry it and check it electrically (→ Section "Preliminary work").
9. Fit new ball bearings (7, 11) (only use authorized ball bearings
(→ Section "Permitted ball bearing types").
10. Fit a new oil seal (3) in the drive end bearing end shield.
11. Reseal the stator seat and grease the V-ring or labyrinth seal (DR63).
12. Fit the motor, brake etc.
13. Then check the gear unit (if applicable) (→ gear unit operating instructions).
Lubrication of the The backstop is supplied with Mobil LBZ low-viscosity grease as a lubricant and
backstop anticorrosion protection. If you want to use a different grease, make sure it complies with
NLGI class 00/000, with a base oil viscosity of 42 mm2/s at 40 °C on a lithium saponified
and mineral oil base. The temperature range extends from -50 °C to +90 °C. See the
following table for the amount of grease required.
Motor type 71/80 90/100 112/132 132M/160M 160L/225

Grease [g] 9 15 15 20 45

Inspection and maintenance of brake BMG02 8
8.4 Inspection and maintenance of brake BMG02
Measuring the The condition of the brake disc is assessed by measuring the thickness of the brake
thickness of the disc. If the brake disc is thinner than the minimum thickness, the BMG02 must be chan-
brake disc, changed (→ following illustration). The working gap cannot be adjusted.
ging the BMG02
brake
1
d
5 4 3
50345AXX
1. Isolate the motor and brake from the supply, safeguarding them against
unintentional power-up
2. Unscrew the hand lever (1, on version with manual brake release). Remove the fan
guard and the fan.
3. Loosen the screws (2) and remove the complete brake with the releasing lever (on
version with manual brake release).
4. Measure thickness "d" of the brake disc (3):
Brake Thickness "d" of the brake disc [mm] Max. braking torque
Type max. min. [Nm]
5.4 0.8
BMG02 6
5.6 1.2
5. If the disc is thinner than the minimum specified thickness, the whole brake
must be renewed.
6. Set the complete brake unit onto the motor:
– Make sure the gearing of the brake disc (4) engages precisely in the gearing of
the carrier precisely (5).
– Route the electrical leads of the brake through the B-endshield and the interior of
the motor to the terminal box.
7. Fasten the brake with the screws (2) onto the B-endshield.
8. Refit fan and fan guard, replace and tighten the hand lever (1) (on version with
manual brake release).

8 Inspection and maintenance of brake BR03
8.5 Inspection and maintenance of brake BR03
13
12 14
11
10
16 15
9
17
18
8
7
12
6
4
5
3
2
1
5
50067AXX
Key
1 Carrier 7 brake disc 13 Hand lever
2 Clip 8 Pressure plate 14 Releasing lever
3 Circlip with stud 15 Sealing washer
4 Friction plate 9 Damping plate 16 Self locking counter nut
5 Bolt 10 Brake springs 17 Conical coil spring
6 Guide ring 11 Brake coil body 18 Sealing element
12 Bolt

Inspection and maintenance of brake BR03 8
Inspecting brake The working air gap cannot be adjusted and can only be measured by means of the
BR03, measuring stroke of the pressure plate when the brake is released.
the working air
gap
unintentional power-up!
guard and the fan.
3. Remove the self-locking counter nuts (16) and, if manual brake release is fitted,
remove the conical coil springs (17) and the releasing lever (14).
4. Measure clearance x (see following illustration) with the brake at rest:
X
50066AXX
– From the end of the stud on the pressure plate (8) to the brake coil body (11).
5. Release the brake electrically.
6. Measure clearance x with the brake released:
– From the end of the stud on the pressure plate (8) to the brake coil body (11).
7. The differential corresponds to the working air gap, i.e. the stroke of the pressure
plate (18):
– If the working air gap ≤ 0.8 mm, reinstall the conical coil springs (17), releasing
lever (14) and self-locking counter nuts (16).
– If the working air gap ≥ 0.8 mm, renew the entire brake unit.
– Use setting nuts to set the floating clearance "s" between the conical coil springs
(pressed flat) and the setting nuts (→ following illustration).
01111BXX
Brake Floating clearance s [mm]

BR03 2
Important: The floating clearance "s" is necessary so that the pressure plate can
move upwards as the brake lining wears. Otherwise, reliable braking is not
guaranteed.

8 Inspection and maintenance of brake BR03
8. Reassemble the removed parts. Install the complete brake (replaced if the working
air gap ≥ 0.8 mm) to the motor (→ following illustration):
– Make sure the gearing of the brake disc engages in the gearing of the carrier and
that the plug on the motor end fits into the socket on the brake end
50175AXX
Altering the The braking torque can be changed in steps (→ Section "Work done, working air gap,
braking torque braking torque of brake BR03, MG 05-8" ).
BR03 • by installing different brake springs,
• by changing the number of brake springs.
unintentional power-up.
guard and the fan.
3. Loosen the screws (12) and remove the complete brake with the releasing lever (on
version with manual brake release).
4. Loosen the screws (5) and remove the guide ring (6) with friction plate (4), brake disc
(7), pressure plate (8) and damping plate (9).
5. Remove the brake springs (10) from the brake coil body (11) and replace them by
new ones.
6. Position the new brake springs symmetrically.
7. Slide the damping plate (9) over two studs attached to the pressure plate (8) so the
embossing pattern is located with the projecting side facing the pressure plate.
8. Pressure plate (8):
– Place on the brake springs (10) together with the damping plate (9)
– Guide the studs attached to the pressure plate (8) through the holes in the brake
coil body (6) and make sure the pressure plate is in the correct position
9. Place the flat side of the brake disc (7) on the pressure plate (8).
Note: Do not bring the disk into contact with grease or oil!
10. Place the guide ring (6) and friction disk (4) onto the brake disc (7), press down and
fit the screws (5).

Inspection and maintenance of brake BR03 8
11. Design with manual brake release:

– Put on the conical coil springs (17) and releasing lever (14), fit the self locking
counter nuts (16)
– With manual brake release: Use setting nuts to set the floating clearance "s"
between the conical coil springs (pressed flat) and the setting nuts
(→ following illustration).
01111BXX

BR03 2
Important: The floating clearance "s" is necessary so that the pressure plate
can move up as the brake lining wears. Otherwise, reliable braking is not
guaranteed.
12. Connect the complete brake back onto the motor (→ following illustration):
– Make sure the gearing of the brake disc engages in the gearing of the carrier and
that the plug on the motor end fits into the socket on the brake end.
50175AXX
13. Fit the fan and fan guard back on, screw the hand lever (10) back in (on version with
manual brake release).

8 Inspection and maintenance of brake BMG 05-8, BM 15 - 62
8.6 Inspection and maintenance of brake BMG 05-8, BM 15 - 62

Brake BM(G)05-15
9
8
8
7
6
5
4
3
2
22
21
e
10 20
c 19
b
a 18
17
16
15
14
11 12 13
01955AXX

Inspection and maintenance of brake BMG 05-8, BM 15 - 62 8
Brake BM30-62
10 e
d
20
a 19
18
17
16
15
14
13
12
11
8
7b
7
6
2 3 5
01956AXX
Key
1 Motor with brake bearing 8 Pressure plate 14 Dowel pin
end shield 9 Damping plate 15 Releasing lever with hand lever
2 Carrier (BMG only) 16 Stud (2 pcs.)
3 Circlip 10 a Stud (3x) 17 Conical coil spring
4 Niro disk (only BMG) b Counter spring 18 Setting nut
5 Rubber sealing collar c Pressure ring 19 Fan
6 Annular spring e Hex nut 20 Circlip
7 brake disc 11 Brake spring 21 Fan guard
7b Only BM 32, 62: 12 Brake coil body 22 Housing screw
Brake stationary disk, 13 In BMG: Sealing washer
annular spring, brake disc In BM: V-ring

Inspecting brake BMG 05–8, BM 15–62, setting the working air gap
2. Remove the following:
– If fitted, forced-cooling fan, tacho/encoder (→ Section "Preliminary work for
motor and brake maintenance").
– Flange cover or fan guard (21).
3. Push the rubber sealing collar (5) aside.
– Release the clip to do this, if necessary.
– Extract the abraded matter.
4. Measure the brake disc (7, 7b):
If the brake disc is:
– ≤ 9 mm on brake motors up to size 100.
– ≤ 10 mm on brake motors up to size 112.
Fit a new brake disc (→ Section "Changing brake disc on BMG 05-8, BM 15-62" ).
5. In BM 30–62:
Loosen the setting sleeve (10d) by turning towards the bearing end shield.
6. Measure the working air gap A
(using a feeler gauge at three points offset by approx. 120° → following illustration):
– In BM, between the pressure plate (8) and the brake coil body (12)
– In BMG, between the pressure plate and the damping plate (9)
7. Tighten the hex nuts (10e).
– Until the working air gap is set correctly (→ Section "Technical Data").
– In BM 30–62, until the working air gap is initially 0.25 mm.
8. In BM 30–62:
Tighten the setting sleeves.
– against the brake coil body.
– until the working air gap is set correctly (→ Section "Technical Data").
9. Fit the rubber sealing collar back in place and re-install the dismantled parts.
01957AXX

Inspection and maintenance of brake BMG 05-8, BM 15 - 62 8
Changing the drake disk BMG 05–8, BM 15–62

When fitting a new brake disc, inspect the other removed parts as well and fit new ones
if necessary (in BMG05-4 ≤ 9 mm; in BMG62 ≤ 10 mm).
– If fitted, forced cooling fan, tacho/encoder (→ Section "Preliminary motor and
brake maintenance").
– Flange cover or fan guard (21), circlip (20) and fan (19).
3. Remove the rubber sealing collar (5) and the manual brake release:
– Setting nuts (18), conical coil springs (17), studs (16), release lever (15), dowel
pin (14).
4. Unscrew hex nuts (10e), carefully pull off the brake coil body (12) (brake cable!) and
take out the brake springs (11).
5. Remove the damping plate (9), pressure plate (8) and brake disc (7, 7b) and clean
the brake components.
6. Fit a new brake disc.
7. Re-install the brake components.
– Except for the rubber sealing collar, fan and fan guard, set the working air gap
(→ ”Inspecting brake BMG 05–8, BM 15–62, setting the working air gap” , points 5
through 8)
8. With manual brake release: Use setting nuts to set the floating clearance "s"
between the conical coil springs (pressed flat) and the setting nuts (→ following
illustration).
01111BXX

BMG 05-1 1.5
BMG 2-8 2
BM 15-62 2
Important: This floating clearance "s" is necessary so that the pressure plate
guaranteed.
Note: • The lockable manual brake release (type HF) is already released if a resistance is
encountered when operating the grub screw.
• The self-reengaging manual brake release (type HR) can be operated with normal
hand pressure.
Important: In brake motors with self-reengaging manual brake release, the
manual brake release lever must be removed after startup/maintenance. A bracket
is provided for storing it on the outside of the motor.

Altering the The braking torque can be changed in steps (→ Section "Technical Data")
braking torque • by installing different brake springs,
BMG 05–8,
• by changing the number of brake springs,
BM 15–62
• by changing the brake coil body:
– BMG 05: if the maximum braking torque is not sufficient for the specific
application, install the brake coil body (12) of brake BMG 1 of the same design in
order to ensure safe braking.
– BMG 2: if the maximum braking torque is not sufficient for the specific
application, install the brake coil body (12) of brake BMG 4 of the same design in
order to ensure safe braking.
– If fitted, forced-cooling fan, tacho/encoder (→ Section "Preliminary work for
motor and brake maintenance").
– Flange cover or fan guard (21), circlip (20) and fan (19).
3. Remove the rubber sealing collar (5) and the manual brake release:
– setting nuts (18), conical coil springs (17), studs (16), release lever (15), dowel
pin (14).
4. Unscrew hex nuts (10e), pull off the coil body (12).
– By approx. 50 mm (watch the brake cable!).
5. Change or add brake springs (11).
– Position the brake springs symmetrically.
6. Re-install the brake components.
– Except for the rubber sealing collar, fan and fan guard,
set the working air gap (→ ”Inspecting brake BMG 05–8, BM 15–62, setting the
working air gap” , points 5 through 8)
7. With manual brake release: Use setting nuts to set floating clearance "s" between
the conical coil springs (pressed flat) and the setting nuts (→ following illustration.)
01111BXX

BMG 05-1 1.5
BMG 2-8 2
BM 15-62 2
Important: This floating clearance "s" is necessary so that the pressure plate
guaranteed.
Note Fit new setting nuts (18) and hexagon nuts (10e) if the removal procedure is repeated!

kVA n
Work done until maintenance, braking torques of brake BMG02 f 9
i
P Hz
9 Technical Data
9.1 Work done until maintenance, braking torques of brake BMG02

Brake For motor size Work done until Thickness of brake Braking torque
type maintenance disc [mm]
[106 J] max. min [Nm]
DT56 5.6 1.2
BMG02 30 6
ET56 5.4 0.8
9.2 Details for ordering BMG02 spares

Brake Voltage Braking torque Part number
type
[VDC] [Nm]
0.8 0574 319 2
BMG02 24
1.2 0574 323 0
0.8 0574 327 3
BMG02/HR 24
1.2 0574 331 1
Brake Voltage Braking torque Part number

type
[VAC] [Nm]
0.8 0574 320 6
230
1.2 0574 324 9
0.8 0574 321 4
BMG02 400
1.2 0574 325 7
0.8 0574 322 2
460/500
1.2 0574 326 5
0.8 0574 328 1
230
1.2 0574 332 X
0.8 0574 329 X
BMG02/HR 400
1.2 0574 333 8
0.8 0574 330 3
460/500
1.2 0574 334 6

kVA n
9 f Work done, working air gap, braking torques of brake BR03, BMG 05-8
i
P Hz
9.3 Work done, working air gap, braking torques of brake BR03, BMG 05-8
Working air gap
Work done Braking torque settings
[mm]
Brake For until
Braking Type and no. of Order number of
type motor size maintenance
[106 J] min.1) max. torque springs springs
[Nm] Normal Red Normal Red
3.2 6 -
2.4 4 2
BR 03 63 200 - 0.8 - 185 815 7 185 873 4
1.6 3
0.8 - 6
5.0 3 -
4.0 2 2
BMG 052) 71 120 2.5 - 6
1.6 - 4
1.2 - 3 135 017 X 135 018 X
10 6 -
BMG 1 80 120 7.5 4 2
6.0 3 3
0.25 0.6
20 3 -
16 2 2
90
BMG 23) 260 10 - 6
100
6.6 - 4
5.0 - 3 135 150 8 135 151 6
40 6 -
BMG 4 100 260 30 4 2
24 3 3
75 6 -
55 4 2
45 3 3
112M 37 3 -
BMG 8 600 0.3 1.2 184 845 3 135 570 8
132S 30 2 2
19 - 6
12.6 - 4
9.5 - 3
1)
1) Please note when checking the working air gap:
Parallelism tolerances on the brake disk may give rise to deviations of ±0.1 mm after a test run.
2) BMG 05:
If the maximum braking torque (5 Nm) is not sufficient, it is possible to install the brake coil body of the BMG 1 brake.
3) BMG 2:
If the maximum braking torque (20 Nm) is not sufficient, it is possible to install the brake coil body of the BMG 4 brake.

kVA n
Work done, working air gap, braking torques of brake BM 15 - 62 f 9
i
P Hz
9.4 Work done, working air gap, braking torques of brake BM 15 - 62
Work done Working air gap

Braking torque settings
until [mm]
Brake For
maintenance Braking Type and no. of Order number of
type motor size
[106 J] min. 1)
max. torque springs springs
[Nm] Normal Red Normal Red
150 6 -
125 4 2
100 3 3
132M, ML
BM 15 1000 75 3 - 184 486 5 184 487 3
160M
50 - 6
35 - 4
25 - 3
160L 0.3 1.2 300 8 -
BM 30 1500
180 250 6 2
200 4 4
150 4 -
200 125 2 4
BM 31 1500 100 - 8
225
75 - 6 136 998 9 136 999 7
50 - 4
300 4 -
250 2 4
BM322) 180 1500 200 - 8
150 - 6
100 - 4
600 8 -
0.4 1.2 500 6 2
400 4 4
200 300 4 -
BM622) 1500 136 998 9 136 999 7
225 250 2 4
200 - 8
150 - 6
100 - 4
1) Please note when checking the working air gap:

Parallelism tolerances on the brake disk may give rise to deviations of ±0.1 mm after a test run.
2) Double disk brake

kVA n
9 f Operating currents
i
P Hz
9.5 Operating currents

The current values IH (holding current) specified in the tables are r.m.s. values. Only use r.m.s. instruments for
your measurement.
The inrush current (accelerator current) IB only flows for a short time (max. 120 ms) when the brake is released
or during voltage dips below 70 % of rated voltage. There is no increased inrush current if the BG brake rectifier
is used or if there is a direct DC voltage supply – both are only possible with brakes up to motor size 100.
Brake BMG02-
BR03 BMG02 BR03
Motor size 56 63
Max. braking torque (Nm) 1.2 3.2
Coil power (W) 25 24
Control factor IB/IH - 4
Voltage VN BMG02 BR03

IH IG IH IG
VAC VDC [AAC] [ADC] [AAC] [ADC]
24 - 0.72 - 0.72
24 (23-26) 10 - - 1.5 1.80
42 (40-45) 18 - - 0.81 1.01
48 (46-50) 20 - - 0.72 0.90
53 (51-56) 22 - - 0.64 0.80
60 (57-63) 24 - - 0.57 0.72
67 (64-70) 27 - - 0.50 0.64
73 (71-78) 30 - - 0.45 0.57
85 (79-87) 36 - - 0.40 0.51
92 (88-98) 40 - - 0.35 0.45
110 (99-110) 44 - - 0.31 0.40
115 (111-123) 48 - - 0.28 0.36
133 (124-138) 54 - - 0.25 0.32
147 (139-154) 60 - - 0.22 0.29
160 (155-173) 68 - - 0.20 0.25
184 (174-193) 75 - - 0.17 0.23
208 (194-217) 85 - - 0.16 0.20
230 (218-243) 96 0.14 0.18 0.14 0.18
254 (244-273) 110 - - 0.12 0.16
290 (274-306) 125 - - 0.11 0.14
318 (307-343) 140 - - 0.10 0.13
360 (344-379) 150 - - 0.09 0.11
400 (380-431) 170 0.08 0.10 0.08 0.10
460 (432-500) 190 0.07 0.09 0.07 0.09
Key IH Holding current r.m.s. value in the connecting harness to the SEW brake rectifier
IB Accelerator current - short-term inrush current
IG Direct current with direct DC voltage supply
VN Rated voltage (rated voltage range)

kVA n
Operating currents f 9
i
P Hz
Brake BMG 05 -
BMG 4 BMG 05 BMG 1 BMG 2 BMG 4
Motor size 71/80 80 90/100 100
Max. braking torque (Nm) 5 10 20 40
Coil power (W) 32 36 40 50
Control factor IB/IH 4 4 4 4
Voltage VN BMG 05 BMG 1 BMG 2 BMG 4

IH IG IH IG IH IG IH IG
VAC VDC
[AAC] [ADC] [AAC] [ADC] [AAC] [ADC] [AAC] [ADC]
24 1.38 1.54 1.77 2.20
24 (23-25) 10 2.0 3.3 2.4 3.7 - - - -
42 (40-46) 18 1.14 1.74 1.37 1.94 1.46 2.25 1.80 2.80
48 (47-52) 20 1.02 1.55 1.22 1.73 1.30 2.00 1.60 2.50
56 (53-58) 24 0.90 1.38 1.09 1.54 1.16 1.77 1.43 2.20
60 (59-66) 27 0.81 1.23 0.97 1.37 1.03 1.58 1.27 2.00
73 (67-73) 30 0.72 1.10 0.86 1.23 0.92 1.41 1.14 1.76
77 (74-82) 33 0.64 0.98 0.77 1.09 0.82 1.25 1.00 1.57
88 (83-92) 36 0.57 0.87 0.69 0.97 0.73 1.12 0.90 1.40
97 (93-104) 40 0.51 0.78 0.61 0.87 0.65 1.00 0.80 1.25
110 (105-116) 48 0.45 0.69 0.54 0.77 0.58 0.90 0.72 1.11
125 (117-131) 52 0.40 0.62 0.48 0.69 0.52 0.80 0.64 1.00
139 (132-147) 60 0.36 0.55 0.43 0.61 0.46 0.70 0.57 0.88
153 (148-164) 66 0.32 0.49 0.39 0.55 0.41 0.63 0.51 0.79
175 (165-185) 72 0.29 0.44 0.34 0.49 0.37 0.56 0.45 0.70
200 (186-207) 80 0.26 0.39 0.31 0.43 0.33 0.50 0.40 0.62
230 (208-233) 96 0.23 0.35 0.27 0.39 0.29 0.44 0.36 0.56
240 (234-261) 110 0.20 0.31 0.24 0.35 0.26 0.40 0.32 0.50
290 (262-293) 117 0.18 0.28 0.22 0.31 0.23 0.35 0.29 0.44
318 (294-329) 125 0.16 0.25 0.19 0.27 0.21 0.31 0.25 0.39
346 (330-369) 147 0.14 0.22 0.17 0.24 0.18 0.28 0.23 0.35
400 (370-414) 167 0.13 0.20 0.15 0.22 0.16 0.25 0.20 0.31
440 (415-464) 185 0.11 0.17 0.14 0.19 0.15 0.22 0.18 0.28
500 (465-522) 208 0.10 0.15 0.12 0.17 0.13 0.20 0.16 0.25
IB Accelerator current – short-term inrush current

kVA n
9 f Operating currents
i
P Hz
Brake BMG 8 -
BM 32/62 BMG 8 BM 15 BM 30/31; 32/62
Motor size 112/132S 132M-160M 160L-225
Max. braking torque (Nm) 75 150 600
Coil power (W) 65 95 95
Control factor IB/IH 6.3 7.5 8.5
Voltage VN BMG 8 BM 15 BM 30/31; 32/62

IH IH IH
VAC VDC
[AAC] [AAC] [AAC]
24 2.771) 4.151) 4.001)
42 (40-46) - 2.31 3.35 3.15
48 (47-52) - 2.10 2.95 2.80
56 (53-58) - 1.84 2.65 2.50
60 (59-66) - 1.64 2.35 2.25
73 (67-73) - 1.46 2.10 2.00
77 (74-82) - 1.30 1.87 1.77
88 (83-92) - 1.16 1.67 1.58
97 (93-104) - 1.04 1.49 1.40
110 (105-116) - 0.93 1.32 1.25
125 (117-131) - 0.82 1.18 1.12
139 (132-147) - 0.73 1.05 1.00
153 (148-164) - 0.66 0.94 0.90
175 (165-185) - 0.59 0.84 0.80
200 (186-207) - 0.52 0.74 0.70
230 (208-233) - 0.46 0.66 0.63
240 (234-261) - 0.41 0.59 0.56
290 (262-293) - 0.36 0.53 0.50
318 (294-329) - 0.33 0.47 0.44
346 (330-369) - 0.29 0.42 0.40
400 (370-414) - 0.26 0.37 0.35
440 (415-464) - 0.24 0.33 0.31
500 (465-522) - 0.20 0.30 0.28
1) Direct current in BSG operation
IB Accelerator current – short-term inrush current

kVA n
Permitted ball bearing types f 9
i
P Hz
9.6 Permitted ball bearing types

Non-driving end B-bearing
Driving end A-bearing
(foot-mounted, flange-mounted,
(AC motor, brake motor)
geared motors)
Motor type
Flange- Foot-
Geared
mounted mounted AC motor Brake motor
motor
motor motor
DT56 - 6302-Z-J - 6001-J 6001-2RS-J
DFR 63 6203-Z-J 6203-Z-J - 6202-J 6202-2RS-J-C3
DT 71 - 80 6204-Z-J 6303-Z-J 6204-Z-J 6203-J 6203-RS-J-C3
DT 90 - DV100 6306-Z-J 6205-J 6205-RS-J-C3
DV 112 - 132 S 6208-Z-J 6307-Z-J 6208-Z-J 6207-J 6207-RS-J-C3
DV 132 M - 160 M 6309-Z-J-C3 6209-2Z-J-C3
DV 160 L - 180 L 6312-Z-J-C3 6213-2Z-J-C3
DV 200 - 225 6314-Z-J-C3 6314-Z-J-C3
9.7 Lubricant table for anti-friction bearings of SEW motors

Ambient temperature Manufacturer Type
–25 °C ... +80 °C Esso Unirex EQ31)
Anti-friction
+80 °C ... +100 °C Klüber Barrierta L55/22)
bearing
–45 °C ... +60 °C Klüber Asonic GHY722)
1) mineral lubricants (= mineral-based anti-friction bearing grease)
2) synthetic lubricants (= synthetic-based anti-friction bearing grease)

Address list
Addresses
Germany
Headquarters Bruchsal SEW-EURODRIVE GmbH & Co Tel. (0 72 51) 75-0
Production Ernst-Blickle-Straße 42 Fax (0 72 51) 75-19 70
Sales D-76646 Bruchsal http://www.SEW-EURODRIVE.de
Service P.O. Box [email protected]
Postfach 3023 · D-76642 Bruchsal
Production Graben SEW-EURODRIVE GmbH & Co Tel. (0 72 51) 75-0
Ernst-Blickle-Straße 1 Fax (0 72 51) 75-29 70
D-76676 Graben-Neudorf Telex 7 822 276
P.O. Box
Postfach 1220 · D-76671 Graben-Neudorf
Assembly Garbsen SEW-EURODRIVE GmbH & Co Tel. (0 51 37) 87 98-30
Service (near Hannover) Alte Ricklinger Straße 40-42 Fax (0 51 37) 87 98-55
D-30823 Garbsen [email protected]
P.O. Box
Postfach 110453 · D-30804 Garbsen
Kirchheim SEW-EURODRIVE GmbH & Co Tel. (0 89) 90 95 52-10
(near München) Domagkstraße 5 Fax (0 89) 90 95 52-50
D-85551 Kirchheim [email protected]
Langenfeld SEW-EURODRIVE GmbH & Co Tel. (0 21 73) 85 07-30
(near Düsseldorf) Siemensstraße 1 Fax (0 21 73) 85 07-55
D-40764 Langenfeld [email protected]
Meerane SEW-EURODRIVE GmbH & Co Tel. (0 37 64) 76 06-0
(near Zwickau) Dänkritzer Weg 1 Fax (0 37 64) 76 06-30
D-08393 Meerane [email protected]
Additional addresses for service in Germany provided on request!
France
Production Haguenau SEW-USOCOME SAS Tel. 03 88 73 67 00
Sales 48-54, route de Soufflenheim Fax 03 88 73 66 00
Service B. P. 185 http://www.usocome.com
F-67506 Haguenau Cedex [email protected]
Assembly Bordeaux SEW-USOCOME SAS Tel. 05 57 26 39 00
Sales Parc d’activités de Magellan Fax 05 57 26 39 09
Service 62, avenue de Magellan - B. P. 182
F-33607 Pessac Cedex
Lyon SEW-USOCOME SAS Tel. 04 72 15 37 00
Parc d’Affaires Roosevelt Fax 04 72 15 37 15
Rue Jacques Tati
F-69120 Vaulx en Velin
Paris SEW-USOCOME SAS Tel. 01 64 42 40 80
Zone industrielle Fax 01 64 42 40 88
2, rue Denis Papin
F-77390 Verneuil I’Etang
Additional addresses for service in France provided on request!
Argentina
Assembly Buenos Aires SEW EURODRIVE ARGENTINA S.A. Tel. (3327) 45 72 84
Sales Centro Industrial Garin, Lote 35 Fax (3327) 45 72 21
Service Ruta Panamericana Km 37,5 [email protected]
1619 Garin
Australia
Assembly Melbourne SEW-EURODRIVE PTY. LTD. Tel. (03) 99 33 10 00
Sales 27 Beverage Drive Fax (03) 99 33 10 03
Service Tullamarine, Victoria 3043
Sydney SEW-EURODRIVE PTY. LTD. Tel. (02) 97 25 99 00
9, Sleigh Place, Wetherill Park Fax (02) 97 25 99 05
New South Wales, 2164
Austria
Assembly Wien SEW-EURODRIVE Ges.m.b.H. Tel. (01) 6 17 55 00-0
Sales Richard-Strauss-Strasse 24 Fax (01) 6 17 55 00-30
Service A-1230 Wien [email protected]
09/2001
Address list
Belgium
Assembly Brüssel CARON-VECTOR S.A. Tel. (010) 23 13 11
Sales Avenue Eiffel 5 Fax (010) 2313 36
Service B-1300 Wavre http://www.caron-vector.be
[email protected]
Brazil
Production Sao Paulo SEW DO BRASIL Tel. (011) 64 60-64 33
Sales Motores-Redutores Ltda. Fax (011) 64 80 33 28
Service Rodovia Presidente Dutra, km 208 [email protected]
CEP 07210-000 - Guarulhos - SP
Additional addresses for service in Brazil provided on request!
Bulgaria
Sales Sofia BEVER-DRIVE GMBH Tel. (92) 9 53 25 65
Bogdanovetz Str.1 Fax (92) 9 54 93 45
BG-1606 Sofia [email protected]
Canada
Assembly Toronto SEW-EURODRIVE CO. OF CANADA LTD. Tel. (905) 7 91-15 53
Sales 210 Walker Drive Fax (905) 7 91-29 99
Service Bramalea, Ontario L6T3W1 www.sew-eurodrive.ca
Vancouver SEW-EURODRIVE CO. OF CANADA LTD. Tel. (604) 9 46-55 35
7188 Honeyman Street Fax (604) 946-2513
Delta. B.C. V4G 1 E2
Montreal SEW-EURODRIVE CO. OF CANADA LTD. Tel. (514) 3 67-11 24
2555 Rue Leger Street Fax (514) 3 67-36 77
LaSalle, Quebec H8N 2V9
Additional addresses for service in Canada provided on request!
Chile
Assembly Santiago de SEW-EURODRIVE CHILE Tel. (02) 6 23 82 03+6 23 81 63
Sales Chile Motores-Reductores LTDA. Fax (02) 6 23 81 79
Service Panamericana Norte No 9261
Casilla 23 - Correo Quilicura
RCH-Santiago de Chile
China
Production Tianjin SEW-EURODRIVE (Tianjin) Co., Ltd. Tel. (022) 25 32 26 12
Assembly No. 46, 7th Avenue, TEDA Fax (022) 25 32 26 11
Sales Tianjin 300457
Service
Colombia
Assembly Bogotá SEW-EURODRIVE COLOMBIA LTDA. Tel. (0571) 5 47 50 50
Sales Calle 22 No. 132-60 Fax (0571) 5 47 50 44
Service Bodega 6, Manzana B [email protected]
Santafé de Bogotá
Croatia
Sales Zagreb KOMPEKS d. o. o. Tel. +385 14 61 31 58
Service PIT Erdödy 4 II Fax +385 14 61 31 58
HR 10 000 Zagreb
Czech Republic
Sales Praha SEW-EURODRIVE S.R.O. Tel. 02/20 12 12 34 + 20 12 12 36
Business Centrum Praha Fax 02/20 12 12 37
Luná 591 [email protected]
16000 Praha 6
Denmark
Assembly Kopenhagen SEW-EURODRIVEA/S Tel. 4395 8500
Sales Geminivej 28-30, P.O. Box 100 Fax 4395 8509
Service DK-2670 Greve http://www.sew-eurodrive.dk
[email protected]
Estonia
Sales Tallin ALAS-KUUL AS Tel. 6 59 32 30
Paldiski mnt.125 Fax 6 59 32 31
EE 0006 Tallin
09/2001
Address list
Finland
Assembly Lahti SEW-EURODRIVE OY Tel. (3) 589 300
Sales Vesimäentie 4 Fax (3) 780 6211
Service FIN-15860 Hollola 2
Great Britain
Assembly Normanton SEW-EURODRIVE Ltd. Tel. 19 24 89 38 55
Sales Beckbridge Industrial Estate Fax 19 24 89 37 02
Service P.O. Box No.1
GB-Normanton, West- Yorkshire WF6 1QR
Greece
Sales Athen Christ. Boznos & Son S.A. Tel. 14 22 51 34
Service 12, Mavromichali Street Fax 14 22 51 59
P.O. Box 80136, GR-18545 Piraeus [email protected]
Hong Kong
Assembly Hong Kong SEW-EURODRIVE LTD. Tel. 2-7 96 04 77 + 79 60 46 54
Sales Unit No. 801-806, 8th Floor Fax 2-7 95-91 29
Service Hong Leong Industrial Complex [email protected]
No. 4, Wang Kwong Road
Kowloon, Hong Kong
Hungary
Sales Budapest SEW-EURODRIVE Kft. Tel. +36 1 437 06 58
Service H-1037 Budapest Fax +36 1 437 06 50
Kunigunda u. 18
India
Assembly Baroda SEW-EURODRIVE India Pvt. Ltd. Tel. 0 265-83 10 86
Sales Plot No. 4, Gidc Fax 0 265-83 10 87
Service Por Ramangamdi · Baroda - 391 243 [email protected]
Gujarat
Ireland
Sales Dublin Alperton Engineering Ltd. Tel. (01) 8 30 62 77
Service 48 Moyle Road Fax (01) 8 30 64 58
Dublin Industrial Estate
Glasnevin, Dublin 11
Italy
Assembly Milano SEW-EURODRIVE di R. Blickle & Co.s.a.s. Tel. (02) 96 98 01
Sales Via Bernini,14 Fax (02) 96 79 97 81
Service I-20020 Solaro (Milano)
Japan
Assembly Toyoda-cho SEW-EURODRIVE JAPAN CO., LTD Tel. (0 53 83) 7 3811-13
Sales 250-1, Shimoman-no, Fax (0 53 83) 7 3814
Service Toyoda-cho, Iwata gun
Shizuoka prefecture, P.O. Box 438-0818
Korea
Assembly Ansan-City SEW-EURODRIVE KOREA CO., LTD. Tel. (031) 4 92-80 51
Sales B 601-4, Banweol Industrial Estate Fax (031) 4 92-80 56
Service Unit 1048-4, Shingil-Dong [email protected]
Ansan 425-120
Luxembourg
Assembly Brüssel CARON-VECTOR S.A. Tel. (010) 23 13 11
Sales Avenue Eiffel 5 Fax (010) 2313 36
Service B-1300 Wavre http://www.caron-vector.be
[email protected]
Macedonia
Sales Skopje SGS-Skopje / Macedonia Tel. (0991) 38 43 90
"Teodosij Sinactaski” Fax (0991) 38 43 90
6691000 Skopje / Macedonia
Malaysia
Assembly Johore SEW-EURODRIVE SDN BHD Tel. (07) 3 54 57 07 + 3 54 94 09
Sales No. 95, Jalan Seroja 39, Taman Johor Jaya Fax (07) 3 5414 04
Service 81000 Johor Bahru, Johor
West Malaysia
09/2001
Address list
Netherlands
Assembly Rotterdam VECTOR Aandrijftechniek B.V. Tel. +31 10 44 63 700
Sales Industrieweg 175 Fax +31 10 41 55 552
Service NL-3044 AS Rotterdam http://www.vector.nu
Postbus 10085 [email protected]
NL-3004 AB Rotterdam
New Zealand
Assembly Auckland SEW-EURODRIVE NEW ZEALAND LTD. Tel. 0064-9-2 74 56 27
Sales P.O. Box 58-428 Fax 0064-9-2 74 01 65
Service 82 Greenmount drive [email protected]
East Tamaki Auckland
Christchurch SEW-EURODRIVE NEW ZEALAND LTD. Tel. 0064-3-3 84 62 51
10 Settlers Crescent, Ferrymead Fax 0064-3-3 85 64 55
Christchurch [email protected]
Norway
Assembly Moss SEW-EURODRIVE A/S Tel. (69) 2410 20
Sales Solgaard skog 71 Fax (69) 2410 40
Service N-1599 Moss [email protected]
Peru
Assembly Lima SEW DEL PERU MOTORES REDUCTORES Tel. (511) 349-52 80
Sales S.A.C. Fax (511) 349-30 02
Service Los Calderos # 120-124 [email protected]
Urbanizacion Industrial Vulcano, ATE, Lima
Poland
Sales Lodz SEW-EURODRIVE Polska Sp.z.o.o. Tel. (042) 6 16 22 00
ul. Pojezierska 63 Fax (042) 6 16 22 10
91-338 Lodz [email protected]
Portugal
Assembly Coimbra SEW-EURODRIVE, LDA. Tel. (0231) 20 96 70
Sales Apartado 15 Fax (0231) 20 36 85
Service P-3050-901 Mealhada [email protected]
Romania
Sales Bucuresti Sialco Trading SRL Tel. (01) 2 30 13 28
Service str. Madrid nr.4 Fax (01) 2 30 71 70
71222 Bucuresti [email protected]
Russia
Sales St. Petersburg ZAO SEW-EURODRIVE Tel. (812) 3 26 09 41 + 5 35 04 30
P.O. Box 193 Fax (812) 5 35 22 87
193015 St. Petersburg [email protected]
Singapore
Assembly SEW-EURODRIVE PTE. LTD. Tel. 8 62 17 01-705
Sales No 9, Tuas Drive 2 Fax 8 61 28 27
Service Jurong Industrial Estate Telex 38 659
Singapore 638644
Slovenia
Sales Celje Pakman - Pogonska Tehnika d.o.o. Tel. 00386 3 490 83 20
Service UI. XIV. divizije 14 Fax 00386 3 490 83 21
SLO – 3000 Celje [email protected]
09/2001
Address list
South Africa
Assembly Johannesburg SEW-EURODRIVE (PROPRIETARY) LIMITED Tel. + 27 11 248 70 00
Sales Eurodrive House Fax +27 11 494 23 11
Service Cnr. Adcock Ingram and Aerodrome Roads [email protected]
Aeroton Ext. 2
Johannesburg 2013
P.O.Box 90004
Bertsham 2013
Capetown SEW-EURODRIVE (PROPRIETARY) LIMITED Tel. +27 21 552 98 20
Rainbow Park Fax +27 21 552 98 30
Cnr. Racecourse & Omuramba Road Telex 576 062
Montague Gardens
Cape Town
P.O.Box 36556
Chempet 7442
Cape Town
Durban SEW-EURODRIVE (PROPRIETARY) LIMITED Tel. +27 31 700 34 51
2 Monaceo Place Fax +27 31 700 38 47
Pinetown
Durban
P.O. Box 10433, Ashwood 3605
Spain
Assembly Bilbao SEW-EURODRIVE ESPAÑA, S.L. Tel. 9 44 31 84 70
Sales Parque Tecnológico, Edificio, 302 Fax 9 44 31 84 71
Service E-48170 Zamudio (Vizcaya) [email protected]
Sweden
Assembly Jönköping SEW-EURODRIVE AB Tel. (036) 34 42 00
Sales Gnejsvägen 6-8 Fax (036) 34 42 80
Service S-55303 Jönköping www.sew-eurodrive.se
Box 3100 S-55003 Jönköping
Switzerland
Assembly Basel Alfred lmhof A.G. Tel. (061) 4 17 17 17
Sales Jurastrasse 10 Fax (061) 4 17 17 00
Service CH-4142 Münchenstein bei Basel http://www.imhof-sew.ch
[email protected]
Thailand
Assembly Chon Buri SEW-EURODRIVE (Thailand) Ltd. Tel. 0066-38 21 40 22
Sales Bangpakong Industrial Park 2 Fax 0066-38 21 45 31
Service 700/456, Moo.7, Tambol Donhuaroh [email protected]
Muang District
Chon Buri 20000
Turkey
Assembly Istanbul SEW-EURODRIVE Tel. (0216) 4 41 91 63 + 4 41 91 64 + 3
Sales Hareket Sistemleri San. ve Tic. Ltd. Sti 83 80 14 + 3 83 80 15
Service Bagdat Cad. Koruma Cikmazi No. 3 Fax (0216) 3 05 58 67
TR-81540 Maltepe ISTANBUL [email protected]
USA
Production Greenville SEW-EURODRIVE INC. Tel. (864) 4 39 75 37
Assembly 1295 Old Spartanburg Highway Fax Sales (864) 439-78 30
Sales P.O. Box 518 Fax Manuf. (864) 4 39-99 48
Service Lyman, S.C. 29365 Fax Ass. (864) 4 39-05 66
Telex 805 550
Assembly San Francisco SEW-EURODRIVE INC. Tel. (510) 4 87-35 60
Sales 30599 San Antonio St. Fax (510) 4 87-63 81
Service Hayward, California 94544-7101
Philadelphia/PA SEW-EURODRIVE INC. Tel. (856) 4 67-22 77
Pureland Ind. Complex Fax (856) 8 45-31 79
200 High Hill Road, P.O. Box 481
Bridgeport, New Jersey 08014
Dayton SEW-EURODRIVE INC. Tel. (9 37) 3 35-00 36
2001 West Main Street Fax (9 37) 4 40-37 99
Troy, Ohio 45373
Dallas SEW-EURODRIVE INC. Tel. (214) 3 30-48 24
3950 Platinum Way Fax (214) 3 30-47 24
Dallas, Texas 75237
09/2001
Address list
USA
Additional addresses for service in the USA provided on request!
Venezuela
Assembly Valencia SEW-EURODRIVE Venezuela S.A. Tel. +58 (241) 8 32 98 04
Sales Av. Norte Sur No. 3, Galpon 84-319 Fax +58 (241) 8 38 62 75
Service Zona Industrial Municipal Norte [email protected]
Valencia [email protected]
09/2001
SEW-EURODRIVE GmbH & Co · P.O. Box 3023 · D-76642 Bruchsal/Germany · Phone +49-7251-75-0
Fax +49-7251-75-1970 · http://www.sew-eurodrive.com · [email protected]

AC Motors Asynchronous Servomotors: Operating Instructions

Uploaded by

Copyright:

Available Formats

AC Motors Asynchronous Servomotors: Operating Instructions

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

AC Motors Asynchronous Servomotors: Operating Instructions

Uploaded by

Copyright:

Available Formats

Edition

2 Safety Notes ...................................................................................................... 5

3 Motor Design ..................................................................................................... 6

5 Electrical Installation ...................................................................................... 12

7 Operation and Service .................................................................................... 25

8 Inspection and Maintenance .......................................................................... 27

Operating Instructions – AC Motors, Asynchronous Servomotors 3

Tips and information

A requirement of fault-free operation and fulfillment of any rights to claim under

Waste disposal This product consists of

4 Operating Instructions – AC Motors, Asynchronous Servomotors

All work related to transport, storage, assembly / mounting, connection, startup,

Severe injuries and damage to property may result from

Assembly / Observe the notes in the section on "Mechanical Installation"!

Inspections / Observe the notes in the section on "Inspection / Maintenance"!

Operating Instructions – AC Motors, Asynchronous Servomotors 5

3.1 Design principle of the AC motor

6 Operating Instructions – AC Motors, Asynchronous Servomotors

3.2 Nameplate, unit designation

DFV 160 M 4 /BM

DFV 132M2 / BM / TF / AMA1 / EV1T

Motor option protection cover

Example: Fabrication number

01. 301234568. 0001. 00

Operating Instructions – AC Motors, Asynchronous Servomotors 7

230~ 20 BGE 1.5

CT 90L4 / BMG / TF / AV1Y

CFV 132M4 / BM / TF / EV1S

5 V TTL incremental encoder option

Example: Fabrication number

01. 3410069302. 0001. 00

8 Operating Instructions – AC Motors, Asynchronous Servomotors

It is essential to comply with the safety notes in section 2 during installation!

4.1 Before you begin

4.2 Preliminary work

Operating Instructions – AC Motors, Asynchronous Servomotors 9

Drying the motor Heat up the motor

4.3 Installing the motor

10 Operating Instructions – AC Motors, Asynchronous Servomotors

4.4 Installation tolerances

Operating Instructions – AC Motors, Asynchronous Servomotors 11

5.1 Wiring notes

5.2 Special aspects for operation with a frequency inverter

5.3 Special aspects of operation of single-phase motors

12 Operating Instructions – AC Motors, Asynchronous Servomotors

5.4 Special aspects of torque motors and low-speed motors

5.5 Replacement of cable screw fitting threads

Cable screw fitting

Operating Instructions – AC Motors, Asynchronous Servomotors 13

5.6 Special aspects in switching operation

5.7 Connecting the motor

Connecting the • According to circuit diagram (enclosed)

14 Operating Instructions – AC Motors, Asynchronous Servomotors

5.8 Preparation for connecting motor size 63 – knockout

Caution - Do not knock through to the inside of the terminal box!

5.9 Connecting the DT56...+/BMG motor

Operating Instructions – AC Motors, Asynchronous Servomotors 15

5.10 The ET56 single-phase design

A full-load startup can only be prevented by employment of the running capacitor!