Toyota Navigation System Reference Guide

1 QUICK GUIDE 11
2 BASIC FUNCTION 29
3 AUDIO SYSTEM 69
4 VOICE COMMAND SYSTEM 123
5 INFORMATION 135
6 PERIPHERAL MONITORING SYSTEM 139
7 PHONE 149
8 NAVIGATION SYSTEM* 189
9 Entune App Suite* 255
INDEX 269
For more information about the following items, see the “Owner’s Manual”.
 Vehicle customization settings
*: Entune Premium Audio only
1
Introduction
NAVIGATION SYSTEM OWNER’S MANUAL

This manual explains the operation of the navigation/multimedia system.
Please read this manual carefully to ensure proper use. Keep this manual in
your vehicle at all times.
The screen shots in this document and the actual screens of the navigation/
multimedia system differ depending on whether the functions and/or a contract
existed and the map data available at the time of producing this document.
Please be aware that the content of this manual may be different from the
navigation/multimedia system in some cases, such as when the system’s
software is updated.
2
NAVIGATION SYSTEM
The Navigation System is one of the most technologically advanced vehicle ac-
cessories ever developed. The system receives satellite signals from the Global
Positioning System (GPS) operated by the U.S. Department of Defense. Using
these signals and other vehicle sensors, the system indicates your present po-
sition and assists in locating a desired destination.
The navigation system is designed to select efficient routes from your present
starting location to your destination. The system is also designed to direct you
to a destination that is unfamiliar to you in an efficient manner. Map database is
made based on AISIN AW maps, whose information source comes from HERE
maps. The calculated routes may not be the shortest nor the least traffic con-
gested. Your own personal local knowledge or “short cut” may at times be faster
than the calculated routes.
The navigation system’s database includes Point of Interest categories to allow
you to easily select destinations such as restaurants and hotels. If a destination
is not in the database, you can enter the street address or a major intersection
close to it and the system will guide you there.
The system will provide both a visual map and audio instructions. The audio in-
structions will announce the distance remaining and the direction to turn in when
approaching an intersection. These voice instructions will help you keep your
eyes on the road and are timed to provide enough time to allow you to maneu-
ver, change lanes or slow down.
Please be aware that all current vehicle navigation systems have certain limita-
tions that may affect their ability to perform properly. The accuracy of the vehi-
cle’s position depends on satellite conditions, road configuration, vehicle
condition or other circumstances. For more information on the limitations of the
system, refer to page 251.
3
IMPORTANT INFORMATION ABOUT THIS MANUAL
For safety reasons, this manual indicates items requiring particular attention
with the following marks.
CAUTION
● This is a warning against anything which may cause injury to people if the warning is
ignored. You are informed about what you must or must not do in order to reduce the risk
of injury to yourself and others.
NOTICE
● This is a warning against anything which may cause damage to the vehicle or its equip-
ment if the warning is ignored. You are informed about what you must or must not do in
order to avoid or reduce the risk of damage to your vehicle and its equipment.
SYMBOLS USED IN ILLUSTRATIONS
Safety symbol
The symbol of a circle with a slash through it means “Do not”, “Do not do
this” or “Do not let this happen”.
Arrows indicating operations

Indicates the action (pushing, turning,
etc.) used to operate switches and other
devices.
4
HOW TO READ THIS MANUAL
No. Name Description
Operational 
An outline of the operation is explained.
Outlines
Main Operations The steps of an operation are explained.
Related Operations A main operation’s supplementary operations are described.
Information Useful information for the user is described.
5
SAFETY INSTRUCTION CAUTION
(ENTUNE PREMIUM AUDIO)
● For safety, the driver should not operate
the navigation system while he/she is
driving. Insufficient attention to the road
and traffic may cause an accident.
● While driving, be sure to obey the traffic
regulations and maintain awareness of
the road conditions. If a traffic sign on
the road has been changed, route guid-
ance may not have the updated informa-
tion such as the direction of a one way
To use this system in the safest possible street.
manner, follow all the safety tips shown
below. While driving, listen to the voice instruc-
This system is intended to assist in reach- tions as much as possible and glance at
ing the destination and, if used properly, the screen briefly and only when it is safe.
can do so. The driver is solely responsible However, do not totally rely on voice guid-
for the safe operation of your vehicle and ance. Use it just for reference. If the sys-
the safety of your passengers. tem cannot determine the current position
Do not use any feature of this system to correctly, there is a possibility of incorrect,
the extent it becomes a distraction and late, or non-voice guidance.
prevents safe driving. The first priority The data in the system may occasionally
while driving should always be the safe op- be incomplete. Road conditions, including
eration of the vehicle. While driving, be driving restrictions (no left turns, street clo-
sure to observe all traffic regulations. sures, etc.) frequently change. Therefore,
Prior to the actual use of this system, learn before following any instructions from the
how to use it and become thoroughly famil- system, look to see whether the instruction
iar with it. Read the entire Owner’s Manual can be done safely and legally.
to make sure you understand the system. This system cannot warn about such
Do not allow other people to use this sys- things as the safety of an area, condition of
tem until they have read and understood streets, and availability of emergency ser-
the instructions in this manual. vices. If unsure about the safety of an ar-
For your safety, some functions may be- ea, do not drive into it. Under no
come inoperable when driving. Unavail- circumstances is this system a substitute
able screen buttons are dimmed. Only for the driver’s personal judgement.
when the vehicle is not moving, can the Use this system only in locations where it
destination and route selection be done. is legal to do so. Some states/provinces
may have laws prohibiting the use of video
and navigation screens next to the driver.
6
SAFETY INSTRUCTION
(ENTUNE AUDIO PLUS)
To use this system in the safest possible

manner, follow all the safety tips shown
below.
Do not use any feature of this system to
the extent it becomes a distraction and
prevents safe driving. The first priority
while driving should always be the safe op-
eration of the vehicle. While driving, be
sure to observe all traffic regulations.
Prior to the actual use of this system, learn
how to use it and become thoroughly famil-
iar with it. Read the entire Owner's Manual
to make sure you understand the system.
Do not allow other people to use this sys-
tem until they have read and understood
the instructions in this manual.
For your safety, some functions may be-
come inoperable when driving. Unavail-
able screen buttons are dimmed.
CAUTION
● For safety, the driver should not operate

the Multimedia System while he/she is
driving. Insufficient attention to the road
and traffic may cause an accident.
7
TABLE OF CONTENTS
1 QUICK GUIDE 2 BASIC FUNCTION
1. CONTROLS AND FEATURES ........ 12 1. BASIC INFORMATION BEFORE 

CONTROLS OVERVIEW....................... 12 OPERATION.................................. 30
“Apps” SCREEN .................................... 14 INITIAL SCREEN ................................... 30
“Home” SCREEN ................................... 16 TOUCH SCREEN GESTURES.............. 32
“Setup” SCREEN ................................... 20 TOUCH SCREEN OPERATION ............ 33
2. NAVIGATION OPERATION ............ 22 “Home” SCREEN OPERATION ............. 34
“Apps” SCREEN OPERATION............... 35
REGISTERING HOME .......................... 22
ENTERING LETTERS AND NUMBERS/
REGISTERING PRESET 
LIST SCREEN OPERATION ............... 36
DESTINATIONS.................................. 24
SCREEN ADJUSTMENT ....................... 39
OPERATION FLOW: 
GUIDING THE ROUTE ....................... 25 2. Bluetooth® SETTINGS ................... 41
SETTING HOME AS THE  REGISTERING/CONNECTING 
DESTINATION .................................... 26 Bluetooth® DEVICE ............................. 41
3. FUNCTION INDEX........................... 27 SETTING Bluetooth® DETAILS ............. 49
FUNCTION INDEX ................................ 27 3. OTHER SETTINGS ......................... 56

GENERAL SETTINGS ........................... 56
VOICE SETTINGS ................................. 61
VEHICLE SETTINGS ............................. 62
DRIVER SETTINGS............................... 63
MAINTENANCE ..................................... 64
8
3 AUDIO SYSTEM 5 INFORMATION 1
1. BASIC OPERATION........................ 70 1. INFORMATION ............................. 136

2
QUICK REFERENCE ............................ 70 RECEIVING WEATHER 
SOME BASICS...................................... 72 INFORMATION ................................. 136
RECEIVING TRAFFIC MAP
2. RADIO OPERATION ....................... 77 3
INFORMATION ................................. 137
AM/FM RADIO ............................................... 77 DATA SERVICES SETTINGS ............. 138
XM Satellite Radio ................................. 87
4
INTERNET RADIO ................................ 93 PERIPHERAL MONITORING 
6
3. MEDIA OPERATION ....................... 94 SYSTEM
CD ......................................................... 94 5
USB MEMORY ...................................... 97 1. REAR VIEW MONITOR 
iPod ..................................................... 101 SYSTEM ...................................... 140
Bluetooth® AUDIO ............................... 105 REAR VIEW MONITOR SYSTEM ....... 140 6
AUX ......................................................... 109 REAR VIEW MONITOR SYSTEM
PRECAUTIONS ................................ 142
4. AUDIO REMOTE CONTROLS ...... 111
THINGS YOU SHOULD KNOW .......... 147 7
STEERING SWITCHES ...................... 111
5. SETUP ........................................... 112 7 PHONE
AUDIO SETTINGS .............................. 112 8
6. TIPS FOR OPERATING  1. PHONE OPERATION 

THE AUDIO SYSTEM .................. 114 (HANDS-FREE SYSTEM 
FOR CELLULAR PHONES)........ 150 9
OPERATING INFORMATION ............. 114
QUICK REFERENCE .......................... 150
4 VOICE COMMAND SYSTEM SOME BASICS .................................... 151
CALLING ON THE Bluetooth® 
PHONE.............................................. 154
1. VOICE COMMAND SYSTEM 
RECEIVING ON THE Bluetooth® 
OPERATION ................................ 124
PHONE.............................................. 160
VOICE COMMAND SYSTEM.............. 124 TALKING ON THE Bluetooth® 
CASUAL SPEECH  PHONE.............................................. 161
RECOGNIZATION ............................ 129 Bluetooth® PHONE MESSAGE 
COMMAND LIST ................................. 130 FUNCTION ........................................ 164
2. MOBILE ASSISTANT  2. SETUP........................................... 169
OPERATION ................................ 132
PHONE/MESSAGE SETTINGS .......... 169
MOBILE ASSISTANT .......................... 132
3. WHAT TO DO IF... ....................... 181
TROUBLESHOOTING......................... 181
9
TABLE OF CONTENTS
8 NAVIGATION SYSTEM 9 Entune App Suite
1. BASIC OPERATION...................... 190 1. Entune App Suite OVERVIEW .... 256

QUICK REFERENCE .......................... 190 Entune App Suite SERVICE................. 256
MAP SCREEN OPERATION ............... 193 2. Entune App Suite 
MAP SCREEN INFORMATION ........... 198 OPERATION................................ 261
TRAFFIC INFORMATION.................... 202 Entune App Suite ................................. 261
2. DESTINATION SEARCH............... 205 3. SETUP........................................... 268
DESTINATION SEARCH SCREEN..... 205
Entune App Suite SETTINGS .............. 268
SEARCH OPERATION........................ 207
STARTING ROUTE GUIDANCE ......... 218
3. ROUTE GUIDANCE....................... 222 INDEX
ROUTE GUIDANCE SCREEN ............ 222
ALPHABETICAL INDEX................... 270
TYPICAL VOICE GUIDANCE 
PROMPTS......................................... 227
EDITING ROUTE................................. 228
4. MEMORY POINTS......................... 232
MEMORY POINTS SETTINGS ........... 232
5. SETUP ........................................... 241
DETAILED NAVIGATION 
SETTINGS ........................................ 241
TRAFFIC SETTINGS........................... 245
6. TIPS FOR THE NAVIGATION 
SYSTEM ....................................... 251
GPS (GLOBAL POSITIONING 
SYSTEM) .......................................... 251
MAP DATABASE VERSION AND
COVERED AREA.............................. 253
10
1
1
QUICK GUIDE
2
1 CONTROLS AND FEATURES 3
1. CONTROLS OVERVIEW .............. 12

4
2. “Apps” SCREEN .......................... 14
3. “Home” SCREEN ......................... 16

5
STATUS DISPLAY................................. 18
4. “Setup” SCREEN ......................... 20

6
2 NAVIGATION OPERATION
7
1. REGISTERING HOME .................. 22
2. REGISTERING PRESET 8
DESTINATIONS .......................... 24
3. OPERATION FLOW:  9
GUIDING THE ROUTE................ 25
4. SETTING HOME AS THE

DESTINATION ............................ 26
3 FUNCTION INDEX
1. FUNCTION INDEX ........................ 27
11
1. CONTROLS AND FEATURES
1. CONTROLS OVERVIEW
Entune Premium Audio
Entune Audio Plus
12
No. Function Page

1
By touching the screen with your finger, you can control the selected
32
functions.
QUICK GUIDE
Insert a disc into this slot. The CD player turns on immediately. 74
Press to access the Bluetooth® hands-free system and applications. 149
Turn to select a radio station or skip to the next or previous track/file.

77, 87, 94,
Also, the knob can be used to enter selections on the list screens by
97, 101, 105
pressing it.
Press to seek up or down for a radio station or to access a desired 77, 87, 94,
track/file. 97, 101, 105
Map card slot

Do not eject the SD card, as doing so may deactivate the navigation 254
system.
Press to pause or resume playing music. —
Press to access the audio system. The audio system turns on in the
70, 72, 73
last mode used.
Press to display the “Apps” screen. 14, 35
Press to display the “Home” screen. 16, 34
Press to turn the audio system on and off, and turn it to adjust the vol-
72
ume.
Press to eject a disc. 74
13
2. “Apps” SCREEN
Press the “APPS” button to display the “Apps” screen.

14
No. Function Page

1
Select to display the map screen. 190
QUICK GUIDE
Select to display the audio control screen. 70
Select to display the hands-free operation screen. 150
Select to display the “Messages” screen. 164
* Select to display weather information. 136
Select to reorder the applications. 35
* Select to display traffic incidents. 202
* Select to display the traffic map information. 137
Select to display the “Setup” screen. 20
* Select to update the Entune App Suite applications. 262
Select to display the “Maintenance” screen. 64
* Select to display the application screen. 256
If a turn-by-turn navigation application has been downloaded to a con-

* nected phone, the application will be displayed and can be used.  
For details, refer to http://www.toyota.com/entune/.
*: Available in the 48 states, D.C. and Alaska
15
3. “Home” SCREEN
Press the “HOME” button to display the “Home” screen.

The “Home” screen can display multiple information screens, such as the naviga-
tion system, audio system and hands-free system, simultaneously. When a screen
is selected, the selected screen is switched to a full-screen display. The “Home”
screen can be set to either a three-way split screen or a two-way split screen.
For details about setting the “Home” screen:  P.34
Three-way split screen
16
Two-way split screen

1
QUICK GUIDE
No. Function Page
Displays the status display 18
Select to display the “Setup” screen. 20
INFORMATION
● Entune Audio Plus only: Turn-by-turn navigation application screen can be displayed.
17
STATUS DISPLAY
The clock and the condition of the Bluetooth® connection are displayed on the sta-
tus display.
Clock
No. Indicators Conditions
(Gray) (Blue)
No connection Poor Good
 An antenna for the Bluetooth® connection is built into the instru-
The condition of ment panel. The condition of the Bluetooth® connection may dete-
the Bluetooth® riorate and the system may not function when a Bluetooth® phone
connection is used in the following conditions and/or places:
The cellular phone is obstructed by certain objects (such as when
it is behind the seat or in the glove box or console box).
The cellular phone is touching or is covered with metal materials.
 Leave the Bluetooth® phone in a place where the condition of the
Bluetooth® connection is good.
Poor Excellent
 The level of reception does not always correspond with the level
displayed on the cellular phone. The level of reception may not be
The level of re- displayed depending on the phone you have.
ception When the cellular phone is out of the service area or in a place
inaccessible by radio waves, “No Service” is displayed.
 “Rm” is displayed when receiving in a roaming area. While roam-
ing, display “Rm” top-left on the icon.
 The receiving area may not be displayed depending on the type of
phone you have.
18
No. Indicators Conditions

1
QUICK GUIDE
The amount of Empty Full
battery charge  The amount displayed does not always correspond with the
left amount displayed on the Bluetooth® device.
The amount of battery charge left may not be displayed depend-
ing on the type of the Bluetooth® device connected.
This system does not have a charging function.
19
4. “Setup” SCREEN
The items shown on the “Setup” screen can be set. Press the “APPS” button, then
select “Setup” to display the “Setup” screen.
20
No. Function Page

1
Select to change the selected language, operation sound, automatic
56
screen change settings, etc.
QUICK GUIDE
Select to customize the “Home” screen. 34
Select to set the voice settings. 61
Select to adjust the contrast and brightness of the screens. 39
Select to set memory points (home, preset destinations, address book

entries, areas to avoid), navigation details or to delete previous desti- 232, 241
nations.
Select to turn the screen off. 
Select to set radio and external media settings. 112
Select to set the phone sound, contacts, message settings, etc. 169
Select to set Bluetooth® phones and Bluetooth® audio devices. 49
* Select to set Entune App Suite settings. 268
* Select to set data services settings. 138
Select to link the driver’s cellular phone settings (audio presets, lan-
63
guage, etc.).
“Owner’s
Select to set vehicle information.
Manual”
* Select to set traffic information. 245
Select to change the phone data plan pop-up message timing. 

* 
(Connected navigation is iPhone application.)
21
2. NAVIGATION OPERATION
1. REGISTERING HOME*
1 Press the “APPS” button. 4 Select “Go Home”.
5 Select “Yes”.
2 Select “Navigation”.
6 Choose a search method.
3 Select “Dest.”.
 There are different kinds of methods to

search for your home. (P.205)

22
7 Select “Enter”.
1
QUICK GUIDE
8 Select “OK”.
Registration of home is complete.
Registering home in a different way 
P.233
Editing the name, location, phone num-
ber and icon 
P.233
Setting home as the destination 
P.208
23
2. REGISTERING PRESET DESTINATIONS*
1 Press the “APPS” button. 4 Select one of the preset destina-

tion buttons.
5 Select “Yes”.
search for a destination. (P.205)
7 Select “Enter ”.
8 Select a position for this preset

destination.
9 Select “OK”.
Registration of preset destinations is
complete.
Registering preset destinations in a dif-
ferent way
P.234
Editing the name, location, phone num-
ber and icon
P.235
Setting preset destinations as the desti-
nation
P.208
24
3. OPERATION FLOW: GUIDING THE ROUTE*
1 Press the “APPS” button. 5 Select “Go”.

1
QUICK GUIDE
6 Select “OK”.
Selecting routes other than the one recom-
2 Select “Navigation”. mended (P.218)
Guidance to the destination is displayed
on the screen and can be heard via
voice guidance.

search for a destination. (P.205)

25
4. SETTING HOME AS THE DESTINATION*
1 Press the “APPS” button. 5 Select “OK”.

Selecting routes other than the one recom-
mended (P.218)
Guidance to the destination is displayed
on the screen and can be heard via
voice guidance.
4 Select “Go Home”.

26
3. FUNCTION INDEX
1. FUNCTION INDEX
Map*
1
Displaying maps Page
QUICK GUIDE
Viewing the map screen 190
Displaying the current position 193
Viewing the current position vicinity map 196
Changing the scale 193
Changing the map orientation 194
Displaying Points of Interest 198
Displaying the estimated travel/arrival time to the destination 222
Selecting the map mode 194
Displaying traffic information 202
Searching for destinations Page
Searching for the destination 207
Changing the selected search area 208
Route guidance*
Before starting or during route guidance Page
Starting route guide 218
Editing the route 228
Viewing the entire route map 223
Address book Page
Registering address book entries 236
Marking icons on the map 237
Pausing guidance 221
Adjusting route guidance volume 61
Deleting the destination 229
27
3. FUNCTION INDEX
Useful functions
Information Page
Displaying vehicle maintenance* 64
Hands-free system (for cellular phone) Page
Registering/connecting Bluetooth® phone 41
Making a call on a Bluetooth® phone 154
Receiving a call on the Bluetooth® phone 160
Voice command system Page
Operating the system with your voice 124
Peripheral monitoring system Page
Viewing behind the rear of the vehicle 140
28
2
1
BASIC FUNCTION
2
2. SETTING Bluetooth® DETAILS ... 49

BASIC INFORMATION  3
1 “Bluetooth* Setup” SCREEN.................. 49
BEFORE OPERATION
REGISTERING A Bluetooth® 
1. INITIAL SCREEN ........................... 30 DEVICE ............................................... 50
4
DELETING A Bluetooth® DEVICE ......... 51
2. TOUCH SCREEN GESTURES ...... 32 CONNECTING A Bluetooth® DEVICE... 51
EDITING THE Bluetooth® DEVICE 5
3. TOUCH SCREEN OPERATION .... 33
INFORMATION ................................... 53
4. “Home” SCREEN OPERATION.... 34 “System Settings” SCREEN .................. 54
6
5. “Apps” SCREEN OPERATION..... 35
3 OTHER SETTINGS
6. ENTERING LETTERS AND 7
NUMBERS/LIST SCREEN 1. GENERAL SETTINGS .................. 56
OPERATION ................................ 36 GENERAL SETTINGS SCREEN ........... 56
ENTERING LETTERS  8
AND NUMBERS.................................. 36 2. VOICE SETTINGS......................... 61
LIST SCREEN ....................................... 36 VOICE SETTINGS SCREEN ................. 61
9
7. SCREEN ADJUSTMENT ............... 39 3. VEHICLE SETTINGS .................... 62
4. DRIVER SETTINGS ...................... 63

2 Bluetooth® SETTINGS MANUALLY SELECT LINKED 
SETTINGS .......................................... 63
1. REGISTERING/CONNECTING
Bluetooth® DEVICE .................... 41 5. MAINTENANCE ............................ 64
REGISTERING A PHONE 
Bluetooth®
FOR THE FIRST TIME ....................... 41
REGISTERING A Bluetooth® AUDIO
PLAYER FOR THE FIRST TIME ........ 42
PROFILES ............................................. 43
CERTIFICATION ................................... 45
*: Bluetooth is a registered trademark of Bluetooth SIG, Inc.
29
1. BASIC INFORMATION BEFORE OPERATION
1. INITIAL SCREEN
1 When the engine switch is in the “ACC” MAINTENANCE INFORMATION

or “ON” position, the initial screen will (ENTUNE PREMIUM AUDIO)
be displayed and the system will begin
operating. This system reminds users when to re-
place certain parts or components and
shows dealer information (if regis-
tered) on the screen.
When the vehicle reaches a previously
set driving distance or date specified
for a scheduled maintenance check,
the “Maintenance Reminder” screen
will be displayed when the navigation
 Images shown on the initial screen can system is turned on.
be changed to suit individual prefer-
ences. (P.59)
 After a few seconds, the “Caution” screen
will be displayed.
 After about 5 seconds, the “Caution”
screen automatically switches to the next
screen. (Select “Continue” or press the
“HOME” button to display the “Home”
screen.)
CAUTION  To prevent the screen from being dis-

played again, select “Do Not Tell Me
Again”.
● When the vehicle is stopped with the
engine running, always apply the park-  To register maintenance information:
ing brake for safety. P.64
 If is selected, the registered
phone number can be called.
30
RESTARTING THE SYSTEM
When system response is extremely

slow, the system can be restarted.
2
1 Press and hold the “PWR•VOL” knob
BASIC FUNCTION
for 3 or more seconds.
31
2. TOUCH SCREEN GESTURES
Operations are performed by touching the touch screen directly with your finger.
Operation method Outline Main use
Touch
Changing and selecting various set-
Quickly touch and release
tings
once.
Drag*1
Touch the screen with
 Scrolling the lists
your finger, and move the
 Scrolling the map screen*2
screen to the desired posi-
tion.
Flick*1
 Scrolling the main screen page
Quickly move the screen
 Scrolling the map screen*2
by flicking with your finger.
*1: The operations may not be performed on all screens.

*2: Entune Premium Audio only
INFORMATION
● The system may not recognize flick operations in high altitude.
32
3. TOUCH SCREEN OPERATION
This system is operated mainly by the

buttons on the screen. (Referred to as
screen buttons in this manual.)
2
 When a screen button is touched, a
beep sounds. (To set the beep sound,
BASIC FUNCTION
see page 56.)
NOTICE
● To prevent damaging the screen, lightly
touch the screen buttons with your fin-
ger.
● Do not use objects other than your finger
to touch the screen.
● Wipe off fingerprints using a glass clean-
ing cloth. Do not use chemical cleaners
to clean the screen, as they may dam-
age the touch screen.
INFORMATION
● If the system does not respond to touch-
ing the screen button, move your finger
away from the screen and then touch it
again.
● Dimmed screen buttons cannot be oper-
ated.
● The displayed image may become
darker and moving images may be
slightly distorted when the screen is
cold.
● In extremely cold conditions, the screen
may not be displayed and the data input
by a user may be deleted. Also, the
screen buttons may not react properly.
● When you look at the screen through
polarized material such as polarized
sunglasses, the screen may be dark and
hard to see. If so, look at the screen
from different angles, adjust the screen
settings on the “Display Settings” screen
or take off your sunglasses.
33
4. “Home” SCREEN OPERATION
The “Home” screen can display multi- CUSTOMIZING THE “Home”

ple information screens, such as the SCREEN
navigation system, audio system and
hands-free system, simultaneously. The display items/area on the “Home”
screen can be changed.
1 Press the “HOME” button.
2 “Home” screen is displayed.

1 Select .
 When a screen is selected, the selected 2 Select “Home Screen”.

screen will change to a full-screen display.  Select “Two Panel” or “Three Panel”.
3 Select the desired area.
4 Select the desired item.
5 Select “OK”.
INFORMATION
● When the selected item is already being
displayed and another area is selected
for that item, the item that it is replacing
will be displayed in the original item’s
location.
34
5. “Apps” SCREEN OPERATION
You can select an application such as REORDERING APPLICATIONS

navigation, audio, etc., from “Apps”
screen. 1 Select “Reorder”.
1 Press the “APPS” button. 2
BASIC FUNCTION
2 Select the desired application then
or to reorder.
3 Select “OK”.
2 Select the application.
INFORMATION
ated.
● When there are several pages, select
or to change the page.
35
6. ENTERING LETTERS AND NUMBERS/LIST SCREEN OPERATION*
When searching for an address, name, LIST SCREEN

etc., or entering data, letters and num-
bers can be entered via the screen. The list screen may be displayed after
entering characters.
ENTERING LETTERS AND
NUMBERS DISPLAYING THE LIST
1 Enter characters and select “OK”.
No. Function
 Matching items from the database are
Select to enter desired characters. listed even if the entered address or name
is incomplete.
Text field. Entered character(s) will  The list will be displayed automatically if
be displayed. the maximum number of characters is
entered or matching items can be dis-
While typing, when there only one played on a single list screen.
available option for the next charac-
ter(s), the next character(s) will be
displayed in gray text in the text field
automatically. Gray text is entered by
selecting this button.
Select to erase one character.
Select to display the alphabet keys.
Select to display other symbols. INFORMATION

● The number of matching items is shown
 On certain letter entry screens, letters can on the right side of the screen. If the
be entered in upper or lower case. number of matching items is more than
999, the system displays “” on the
: Select to enter in lower case. screen.
: Select to enter in upper case.
 Keyboard layout can be changed.

(P.56)

36
■SELECTING ALL ITEMS LIST SCREEN OPERATION

Some lists contain “Select All”. If “Se- When a list is displayed, use the appro-
lect All” is selected, it is possible to priate screen button to scroll through
select all items. 2
the list.
1 Select “Select All”.
BASIC FUNCTION
Icon Function
“Unselect All”: Unselect all items in the
list. Select to skip to the next or previ-
ous page.
Select and hold or to
scroll through the displayed list.
This indicates the displayed

screen’s position.
If appears to the right of an

item name, the complete name is
too long to display.
Select to scroll to the end of
the name.
Select to move to the begin-
ning of the name.
37
SORTING CHARACTER JUMP BUTTONS

IN LISTS
The order of a list displayed on the
screen can be sorted in the order of Some lists contain character screen
distance from the current location, buttons, “ABC”, “DEF” etc., which al-
date, category, etc. low a direct jump to list entries that be-
gin with the same letter as the
1 Select “Sort”. character screen button.
1 Select the desired character jump but-

tons.
2 Select the desired sorting criteria.
INFORMATION
● Every time the same character screen
button is selected, the list starting with
the subsequent character is displayed.
38
7. SCREEN ADJUSTMENT
The contrast and brightness of the INFORMATION

screen display and the image of the
● When the screen is viewed through
camera display can be adjusted. The polarized sunglasses, a rainbow pattern
screen can also be changed to either may appear on the screen due to optical
2
day or night mode. characteristics of the screen. If this is
disturbing, please operate the screen
1 without polarized sunglasses.
BASIC FUNCTION
Press the “APPS” button.
2 Select “Setup”.
3 Select “Display”.
4 Select the items to be set.
No. Function Page
Select to adjust the screen

display.
40
Select to adjust the camera
display.
Select to turn day mode on/

40
off.
39
ADJUSTING THE CONTRAST/ CHANGING BETWEEN DAY

BRIGHTNESS AND NIGHT MODE
The contrast and brightness of the Depending on the position of the head-
screen can be adjusted according to light switch, the screen changes to day
the brightness of your surroundings. or night mode. This feature is available
when the headlight is switched on.
1 Select “General” or “Camera”.
1 Select “Day Mode”.
General INFORMATION
● If the screen is set to day mode with the
headlight switch turned on, this condition
is memorized even with the engine
turned off.
Camera
Screen button Function
Select to brighten the

“Brightness” “+”
screen.
Select to darken the

“Brightness” “-”
screen.
Select to strengthen the

“Contrast” “+”
contrast of the screen.
Select to weaken the

“Contrast” “-”
contrast of the screen.
3 Select “OK”.
40
2. Bluetooth® SETTINGS
1. REGISTERING/CONNECTING Bluetooth® DEVICE
REGISTERING A Bluetooth® 4 Select “Yes” to register a phone.

PHONE FOR THE FIRST TIME 5 When this screen is displayed, search
for the device name displayed on this
To use the hands-free system, it is screen on the screen of your 2
necessary to register a Bluetooth® Bluetooth® device.
phone with the system.
BASIC FUNCTION
Once the phone has been registered, it
is possible to use the hands-free sys-
tem.
For details about registering a
Bluetooth® device: P.50
1 Turn the Bluetooth® connection setting

of your cellular phone on.  For details about operating the Bluetooth®
device, see the manual that comes with it.
2 Press the “APPS” button.  To cancel the registration, select “Can-
cel”.
6 Register the Bluetooth® device using
your Bluetooth® device.
 A PIN-code is not required for SSP
(Secure Simple Pairing) compatible
Bluetooth® devices. Depending on the
type of Bluetooth® device being con-
nected, a message confirming registra-
tion may be displayed on the Bluetooth®
device’s screen. Respond and operate the
3 Select “Phone”. Bluetooth® device according to the confir-
mation message.
 Operations up to this point can also be
performed by pressing the switch on
the steering wheel or button on the
control panel.
41
7 Check that the screen is displayed REGISTERING A Bluetooth®

when registration is complete.
AUDIO PLAYER FOR THE
 The system waits for connection requests
coming from the registered device. FIRST TIME
 At this stage, the Bluetooth® functions are
not yet available. To use the Bluetooth® audio, it is nec-
essary to register an audio player with
8 Select “OK” when the connection sta-
the system. Once the player has been
tus changes from “Connecting...” to
registered, it is possible to use the
“Connected”.
Bluetooth® audio. This operation can-
not be performed while driving.
For details about registering a
Bluetooth® device: P.50
1 Turn the Bluetooth® connection setting

of your audio player on.
 This function is not available when the
 If an error message is displayed, follow Bluetooth® connection setting of your
the guidance on the screen to try again. audio player is set to off.
2 Press the “AUDIO” button.
3 Select “Source” on the audio control

screen.
4 Select “ Audio”.
5 Select “Yes” to register a audio player.
6 Follow the steps in “REGISTERING A

Bluetooth® DEVICE” from “STEP 2”.
(P.50)
42
PROFILES
This system supports the following services.

2
Bluetooth® Require- Recommen-
Spec Function
Device ments dations
BASIC FUNCTION
Bluetooth®
Phone/ Registering a
Ver. 3.0
Bluetooth® Bluetooth® Specification Bluetooth® de- Ver. 2.0
+EDR
Audio  vice
Player
Bluetooth® Require- Recommen-

Profile Function
Device ments dations
Hands-free 
HFP (Hands-Free Profile) Ver. 1.0 Ver. 1.6
system
OPP (Object Push Profile) Ver. 1.1 Ver. 1.2

Transferring the
PBAP (Phone Book Ac- contacts Ver. 1.0 Ver. 1.1
Bluetooth® cess Pro-file)
Phone
MAP (Message Access Bluetooth®
 Ver. 1.0
Profile) phone message
Connected navi-
SPP (Serial Port Profile) gation*1/Entune  Ver. 1.1
App Suite*2
A2DP (Advanced Audio

Bluetooth® Ver. 1.0 Ver. 1.2
Distribution Profile) Bluetooth® audio
Audio 
AVRCP (Audio/Video Re- system
Player Ver. 1.0 Ver. 1.4
mote Control Profile)
*1: Entune Audio Plus

*2: Entune Premium Audio
INFORMATION
● If your cellular phone does not support HFP, registering the Bluetooth® phone or using
OPP, PBAP, MAP or SPP profiles individually will not be possible.
● If the connected Bluetooth® device version is older than recommended or incompatible,
the Bluetooth® device function may not work properly.
● Refer to http://www.toyota.com/entune/ to find approved Bluetooth® phones for this sys-
tem.
43
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG,
Inc. and any use of such marks by Panasonic Corporation is under license. Other trade-
marks and trade names are those of their respective owners.
44
Canada
CERTIFICATION
 NOTE: This device complies with
U.S.A.
Industry Canada licence-exempt RSS
standard(s). Operation is subject to the 2
 FCC ID: ACJ932YEAP01A727 following two conditions: (1) this device
 NOTE: This device complies with part may not cause interference, and (2) this
BASIC FUNCTION
15 of the FCC Rules. Operation is device must accept any interference,
subject to the following two conditions: including interference that may cause
(1) This device may not cause harmful undesired operation of the device.
interference, and (2) this device must  Le présent appareil est conforme aux
accept any interference received, CNR d’Industrie Canada applicables
including interference that may cause aux appareils radio exempts de licence.
undesired operation. L’exploitation est autorisée aux deux
 FCC WARNING: Changes or conditions suivantes: (1) l’appareil ne
modifications not expressly approved by doit pas produire de brouillage, et (2)
the party responsible for compliance l’utilisateur de l’appareil doit accepter
could void the user’s authority to tout brouillage radioélectrique subi,
operate the equipment. même si le brouillage est susceptible
 CAUTION: Radio frequency radiation d’en compromettre le fonctionnement.
exposure information   NOTE: This radio transmitter (identify
This equipment complies with FCC the device by certification number, or
radiation exposure limits set forth for an model number if Category II) has been
uncontrolled environment. This approved by Industry Canada to
equipment should be installed and operate with the antenna types listed
operated with minimum distance of below with the maximum permissible
20cm between the radiator and your gain and required antenna impedance
body. This transmitter must not be co- for each antenna type indicated.
located or operated in conjunction with Antenna types not included in this list,
any other antenna or transmitter. having a gain greater than the maximum
 FCC WARNING: Any unauthorized gain indicated for that type, are strictly
changes or modifications to this prohibited for use with this device.
equipment would void the user’s  Le présent émetteur radio (identifier le
authority to operate this device. dispositif par son numéro de
certification ou son numéro de modèle
s’il fait partie du matériel de catégorie II)
a été approuvé par Industrie Canada
pour fonctionner avec les types
d’antenne énumérés ci-dessous et
ayant un gain admissible maximal et
l’impédance requise pour chaque type
d’antenne. Les types d’antenne non
inclus dans cette liste, ou dont le gain
est supérieur au gain maximal indiqué,
sont strictement interdits pour
l’exploitation de l’émetteur.
45
Access to http://www.ptc.panasonic.eu/, enter the below Model No. into the keyword
search box, you can download the latest “DECLARATION of CONFORMITY” (DoC).
Model No. YEAP01D103, BT1401
46
BASIC FUNCTION
47
48
2. SETTING Bluetooth® DETAILS
1 Press the “APPS” button. “Bluetooth* Setup” SCREEN
BASIC FUNCTION
Function Page
Registering a Bluetooth® device 50
3 Select “Bluetooth*”.
Deleting a Bluetooth® device 51
4 Select the desired item to be set.
Connecting a Bluetooth® device 51
Editing the Bluetooth® device infor-

53
mation
Bluetooth® system settings 54
DISPLAYING THE “Bluetooth*

Setup” SCREEN IN A
DIFFERENT WAY
1 Press the “APPS” button.
3 Select “Phone”.
4 Select “Connect Phone”.

*: Bluetooth is a registered trademark of
Bluetooth SIG, Inc.
49
REGISTERING A Bluetooth® 4 Register the Bluetooth® device using

DEVICE your Bluetooth® device.
 A PIN-code is not required for SSP
® (Secure Simple Pairing) compatible
Up to 5 Bluetooth devices can be reg-
Bluetooth® devices. Depending on the
istered.
type of Bluetooth® device being con-
Bluetooth® compatible phones (HFP) nected, a message confirming registra-
and audio players (AVP) can be regis- tion may be displayed on the Bluetooth®
tered simultaneously. device’s screen. Respond and operate the
Bluetooth® device according to the confir-
This operation cannot be performed mation message.
while driving.
5 Check that the following screen is dis-
1 Display the “Bluetooth* Setup” screen. played when registration is complete.
(P.49)  The system waits for connection requests
coming from the registered device.
2 Select “Add”.
 At this stage, the Bluetooth® functions are
When another Bluetooth® device is con- not yet available.
nected
6 Select “OK” when the connection sta-
 To disconnect the Bluetooth® device, tus changes from “Connecting...” to
select “Yes”.
“Connected”.
When 5 Bluetooth® devices have al-
ready been registered
 A registered device needs to be replaced.
Select “Yes”, and select the device to be
replaced.
3 When this screen is displayed, search
for the device name displayed on this
screen on the screen of your
Bluetooth® device.  If an error message is displayed, follow
the guidance on the screen to try again.
Bluetooth SIG, Inc.
 For details about operating the Bluetooth®

device, see the manual that comes with it.
 To cancel the registration, select “Can-
cel”.
50
DELETING A Bluetooth® CONNECTING A Bluetooth®

DEVICE DEVICE
1 Display the “Bluetooth* Setup” screen. Up to 5 Bluetooth® devices (Phones 2

(P.49) (HFP) and audio players (AVP)) can be
2 registered.
BASIC FUNCTION
Select “Remove”.
3 Select the desired device. If more than 1 Bluetooth® device has

been registered, select the desired de-
vice to make a connection.
1 Display the “Bluetooth* Setup” screen.

(P.49)
2 Select the device to be connected.
4 Select “Yes” when the confirmation

screen appears.
5 Check that a confirmation screen is
displayed when the operation is com-
plete.
 Supported profile icons will be displayed.
INFORMATION
: Phone
● When deleting a Bluetooth® phone, the
contact data will be deleted at the same : Audio player
time.
: Phone/Entune App Suite (Entune
*: Bluetooth is a registered trademark of Premium Audio only)
Bluetooth SIG, Inc.
 The profile icon for a currently connected
device will be displayed in color.
 Selecting a profile icon which is not cur-
rently connected will switch the connec-
tion to the function.
 If the desired Bluetooth® device is not

on the list, select “Add” to register the
device. (P.50)

Bluetooth SIG, Inc.
51
INFORMATION ■RECONNECTING THE Bluetooth®

PHONE
● It may take time if the device connection
is carried out during Bluetooth® audio
playback. If a Bluetooth® phone is disconnected
● Depending on the type of Bluetooth® due to poor reception from the
device being connected, it may be nec- Bluetooth® network when the engine
essary to perform additional steps on
the device. switch is in the “ACC” or “ON” position,
the system automatically reconnects
the Bluetooth® phone.
■AUTO CONNECTION MODE
 If the system is attempting to connect to a
To turn auto connection mode on, set Bluetooth® phone and the Bluetooth®
“Bluetooth* Power” to on. (P.54) phone is turned off and then back on, the
system will attempt to reconnect.
Leave the Bluetooth® device in a loca-
tion where the connection can be es-
tablished.
 When the engine switch is in the “ACC” or
“ON” position, the system searches for a
nearby registered device.
 The system will connect with the regis-
tered device that was last connected, if it
is nearby.
■CONNECTING MANUALLY
When the auto connection has failed or
“Bluetooth* Power” is turned off, it is
necessary to connect Bluetooth® man-
ually.
1 Follow the steps in “CONNECTING A

Bluetooth® DEVICE” from “STEP 2”.
(P.51)
Bluetooth SIG, Inc.
52
EDITING THE Bluetooth® No. Information

DEVICE INFORMATION The name of the Bluetooth® device.
Can be changed to a desired name.
(P.54)
The Bluetooth® device’s information 2
can be displayed on the screen. The Select to set the Bluetooth® audio
displayed information can be edited.
BASIC FUNCTION
player connection method. (P.54)
1 Display the “Bluetooth* Setup” screen. Device address is unique to the de-
vice and cannot be changed.
(P.49)
Phone number of the Bluetooth®
2 Select the desired device to be edited.
phone.
3 Select “Device Info”.
Compatibility profile of the
Bluetooth® device.
Select to reset all setup items.
INFORMATION
● If 2 Bluetooth® devices have been regis-
tered with the same device name, the
devices can be distinguished by refer-
4 Confirm and change the Bluetooth® ring to the device’s address.
device information. ● Depending on the type of phone, some
information may not be displayed.

Bluetooth SIG, Inc.
53
CHANGING A DEVICE NAME “System Settings” SCREEN

1 Select “Device Name”.
The Bluetooth® settings can be con-
2 Enter the name and select “OK”. firmed and changed.
INFORMATION 1 Display the “Bluetooth* Setup” screen.

(P.49)
● Even if the device name is changed, the
name registered in your Bluetooth® 2 Select “System Settings”.
device does not change.
SETTING AUDIO PLAYER

CONNECTION METHOD
1 Select “Connect Audio Player

From”.
2 Select the desired connection method.
“Vehicle”: Select to connect the audio
system to the audio player.
“Device”: Select to connect the audio
player to the audio system.
 Depending on the audio player, the “Vehi-
cle” or “Device” connection method may
be best. As such, refer to the manual that
comes with the audio player.
 To reset the connection method, select
“Default”. *: Bluetooth is a registered trademark of
Bluetooth SIG, Inc.
54
No. Information Page CHANGING “Bluetooth*

Power”
Select to set Bluetooth®
55
connection on/off.
1 Select “Bluetooth* Power”.
2
Displays system name. When “Bluetooth* Power” is on
Can be changed to a de- 55
The Bluetooth® device is automatically
BASIC FUNCTION
sired name.
connected when the engine switch is in the
PIN-code used when the
“ACC” or “ON” position.
Bluetooth® device was reg-
55
istered. Can be changed to When “Bluetooth* Power” is off
a desired code.
The Bluetooth® device is disconnected,
Device address is unique and the system will not connect to it next
to the device and cannot be  time.
changed.
INFORMATION
Select to set the phone
connection status display  ● While driving, the auto connection state
on/off. can be changed from off to on, but can-
not be changed from on to off.
Select to set the connec-
tion status display of the 
audio player on/off.
EDITING THE Bluetooth* NAME
Compatibility profile of the
 1 Select “Bluetooth* Name”.
system device.
Select to reset all setup 2 Enter a name and select “OK”.


items.
EDITING THE Bluetooth* PIN-
CODE
1 Select “Bluetooth* PIN”.
2 Enter a PIN-code and select “OK”.

Bluetooth SIG, Inc.
55
3. OTHER SETTINGS
1. GENERAL SETTINGS
Settings for the system time, operation GENERAL SETTINGS

sounds, etc., can be changed. SCREEN
3 Select “General”.
56
3. OTHER SETTINGS
No. Function No. Function
Select to adjust the clock, time zone, Select to turn the animations on/off.
etc. (P.58)
Select to customize the startup im- 2
Select to change the language. ages. (P.59)
BASIC FUNCTION
Select to change the unit of mea- Select to customize the screen off
*
sure for distance. image. (P.59)
Select to change the unit of weather Select to delete personal data.

temperature. (P.60)
Select to sound beeps. Select to update software versions.

For details, contact your Toyota
Select to change the screen color. dealer.
Select to update Gracenote® data-

Select to change the keyboard lay-
base versions. For details, contact
out.
your Toyota dealer.
Select to set automatic screen
Select to display the software infor-
changes from the audio control
mation. Notices related to third party
screen to the “Home” screen to on/
software used in this product are en-
off. When set to on, the screen will
listed. (This includes instructions for
automatically return to the “Home”
obtaining such software, where ap-
screen from the audio control
plicable.)
screen after 20 seconds.
Select to set a pop-up message dis- Select to reset all setup items.
played on an iPhone connected via
Bluetooth® on/off when an applica- *: Entune Premium Audio only
tion on the iPhone needs to be acti-
vated.
57
3. OTHER SETTINGS
CLOCK SETTINGS ■SETTING THE TIME ZONE

1 Select “Time Zone”.
Used for adjusting the clock, time
zone, etc. 2 Select the desired time zone.
1 Display the “General Settings” screen.

(P.56)
2 Select “Clock”.

 When “Auto” is selected, the time zone is
automatically adjusted by the GPS.
No. Function
Select to adjust the clock manually.
Select to set the minutes to “00”.
Select to change the clock to 24-hour

format.
Select to adjust the clock automati-

cally by the GPS.
 Entune Audio Plus
When “Auto” is selected, only the
minutes can be set using the GPS.
Select to change the time zone.

(P.58)
Select to set daylight saving time

“Auto”*, “On” or “Off”. When “Au-
to”* is selected, the daylight saving
time is automatically set by the GPS.
4 Select “OK”.
58
3. OTHER SETTINGS
CUSTOMIZING THE STARTUP ■TRANSFERRING IMAGES

AND SCREEN OFF IMAGES 1 Open the cover and connect a USB
memory.
An image can be copied from a USB
2
memory and used as the startup and
screen off images.
BASIC FUNCTION
When the engine switch is in the “ACC”
or “ON” position, the initial screen will
be displayed. (P.30)
When “Screen Off” on the “Setup”
screen is selected, the screen is turned
off and the desired screen off image
that is set is displayed. (To turn the
screen off: P.20)  Turn on the power of the USB memory if it
is not turned on.
4 Select “General”.
5 Select “Customize Startup Image” or

“Customize Screen Off Image”.
6 Select “Transfer”.
7 Select “Yes”.
INFORMATION
● When saving the images to a USB,
name the folder that the startup image is
saved to “StartupImage” and name the
folder that the screen off image is saved
to “DisplayOffImage”. If these folder
names are not used, the system cannot
download the images. (The folder
names are case sensitive.)
● The compatible file extensions are JPG
and JPEG.
● An image’s file name, including file
extension, can be up to 32 characters.
● Image files of 5 MB or less can be trans-
ferred.
● Up to 3 images can be downloaded.
● Files with non-ASCII filenames cannot
be downloaded.
59
3. OTHER SETTINGS
■SETTING THE STARTUP IMAGES DELETING PERSONAL DATA

(P.56)
(P.56)
2 Select “Customize Startup Image”.
2 Select “Delete Personal Data”.
3 Select the desired image.
3 Select “Delete”.
4 Select “OK”.
■SETTINGS THE SCREEN OFF IM- screen appears.
AGES  Registered or changed personal settings
will be deleted or returned to their default
1 Display the “General Settings” screen. conditions.
(P.56) For example:
• General settings
2 Select “Customize Screen Off Im- • Navigation settings*
• Audio settings
age”.
• Phone settings
3 Select the desired image. *: Entune Premium Audio only
NOTICE

● Make sure the map microSD card is
inserted when deleting personal data.
The personal data cannot be deleted
when the map microSD card is
removed. To delete the data, after insert-
ing the map microSD card, turn the
4 Select “OK”. engine switch to the “ACC” or “ON” posi-
tion.
60
3. OTHER SETTINGS
2. VOICE SETTINGS
Voice volume, etc., can be set. VOICE SETTINGS SCREEN

BASIC FUNCTION
3 Select “Voice”.
INFORMATION
No. Function
● “Voice Settings” screen can also be dis-
played from the voice recognition top Select to adjust the volume of voice
screen. (P.126) guidance.
Select to set the voice guidance dur-

*
ing route guidance on/off.
Select to set the voice recognition

prompts.
Select to train voice recognition.

The voice command system adapt
the user accent.
Select to set the voice prompt inter-

rupt on/off.
Select to set the web search engine.

* The search engines are Entune App
Suite applications. (P.261)
Select to set the voice recognition

tutorial.
61
3. OTHER SETTINGS
3. VEHICLE SETTINGS
Vehicle customization settings can be

changed.
3 Select “Vehicle”.
4 Select “Vehicle Customization”.
 For details, refer to “Owner’s Manual”.
62
3. OTHER SETTINGS
4. DRIVER SETTINGS
The driver settings feature will allow MANUALLY SELECT LINKED

the system to link some preferences SETTINGS
(such as audio presets, button colors,
language, etc.) to a paired Bluetooth® 1 Display the driver settings screen. 2
phone. (P.63)
2
BASIC FUNCTION
1 Press the “APPS” button. Select “Manually Select Linked Set-
tings”.
3 Select the desired phone.

3 Select “Driver”.
4 Select “Enable this Feature”.
63
3. OTHER SETTINGS
5. MAINTENANCE*
When the system is turned on, the No. Function

“Maintenance Reminder” screen dis-
Select to set the condition of parts or
plays when it is time to replace a part
components.
or certain components. (P.30)
Select to add new information items
1 Press the “APPS” button. separately from provided ones.
Select to cancel all conditions which

have been entered.
Select to reset the item which have

expired conditions.
Select to call the registered dealer.
Select to register/edit dealer infor-

mation. (P.65)
When set to on, the indicator will illu-

2 Select “Maintenance”. minate. The system is set to give
maintenance information with the
3 Select the desired item. “Maintenance Reminder” screen.
(P.30)
INFORMATION
● When the vehicle needs to be serviced,
the screen button color will change to
orange.

64
3. OTHER SETTINGS
MAINTENANCE INFORMATION DEALER SETTING

SETTING
Dealer information can be registered in
1 Select the desired part or component the system. With dealer information
2
screen button. registered, route guidance to the deal-
 When the vehicle needs to be serviced, er is available.
BASIC FUNCTION
the screen button color will change to
orange. 1 Select “Set Dealer”.
2 Set the conditions. 2 Select the desired item to search for
the location. (P.205)
No. Function
 The editing dealer screen appears after
Select to enter the next maintenance setting the location.
date.
Select to enter the driving distance

until the next maintenance check.
Select to cancel the conditions which

have been entered.
Select to reset the conditions which

have expired.
3 Select “OK” after entering the condi-

tions.
INFORMATION
● For scheduled maintenance information,
refer to “Scheduled Maintenance
Guide”, or “Owner’s Manual Supple-
ment”.
● Depending on driving or road conditions,
the actual date and distance that main-
tenance should be performed may differ
from the stored date and distance in the
system.
65
3. OTHER SETTINGS
3 Select the items to be edited. ■EDITING DEALER OR CONTACT

NAME
1 Select “Edit” next to “Dealer” or “Con-
tact”.
2 Enter the name and select “OK”.
■EDITING THE LOCATION

1 Select “Edit” next to “Location”.
No. Function Page
2 Scroll the map to the desired point
Select to enter the name of (P.197) and select “OK”.
66
a dealer.
■EDITING PHONE NUMBER
Select to enter the name of
66
a dealer member. 1 Select “Edit” next to “Phone #”.
Select to set the location. 66 2 Enter the phone number and select
“OK”.
Select to enter the phone
66
number.
Select to delete the dealer

information displayed on 
the screen.
Select to set the displayed

218
dealer as a destination.
66
3. OTHER SETTINGS
BASIC FUNCTION
67
3
AUDIO SYSTEM
1 BASIC OPERATION 2 RADIO OPERATION
1. QUICK REFERENCE ..................... 70 1. AM/FM RADIO...................................... 77

OVERVIEW ............................................ 77
2. SOME BASICS............................... 72
PRESETTING A STATION .................... 80
TURNING THE SYSTEM 
SELECTING A STATION 
ON AND OFF ...................................... 72
FROM THE LIST ................................. 80
SELECTING AN AUDIO SOURCE........ 73
CACHING A RADIO PROGRAM 
DISC SLOT ............................................ 74 (ENTUNE PREMIUM AUDIO 
USB/AUX PORT .................................... 74 ONLY).................................................. 81
SOUND SETTINGS ............................... 75 RADIO BROADCAST DATA 
VOICE COMMAND SYSTEM ................ 76 SYSTEM .............................................. 82
TRAFFIC ANNOUNCEMENT 
(FM RADIO)......................................... 83
USING HD Radio™ TECHNOLOGY...... 83
AVAILABLE HD Radio™ 
TECHNOLOGY.................................... 84
TROUBLESHOOTING GUIDE............... 86
2. XM Satellite Radio ........................ 87

OVERVIEW ............................................ 87
HOW TO SUBSCRIBE TO 
XM Satellite Radio ............................... 89
DISPLAYING THE RADIO ID................. 91
PRESETTING A CHANNEL................... 91
SELECTING A CHANNEL 
FROM THE LIST ................................. 91
IF THE SATELLITE RADIO TUNER
MALFUNCTIONS ................................ 92
3. INTERNET RADIO......................... 93
LISTENING TO INTERNET RADIO ....... 93
68
3
1
AUDIO SYSTEM
2
3 MEDIA OPERATION 4 AUDIO REMOTE CONTROLS 3
1. CD .................................................. 94 1. STEERING SWITCHES............... 111

OVERVIEW ........................................... 94 4
PLAYING AN AUDIO CD ...................... 96
5 SETUP
PLAYING AN MP3/WMA/AAC DISC ..... 96
5
1. AUDIO SETTINGS ...................... 112
2. USB MEMORY............................... 97
“Audio Settings” SCREEN ................... 112
OVERVIEW ........................................... 97
6
PLAYING A USB AUDIO ..................... 100
TIPS FOR OPERATING 
3. iPod.............................................. 101 6
THE AUDIO SYSTEM 7
OVERVIEW ......................................... 101
PLAYING AN iPod............................... 104
1. OPERATING INFORMATION ..... 114
4. Bluetooth® AUDIO ...................... 105 RADIO.................................................. 114 8
OVERVIEW ......................................... 105 CD PLAYER AND DISC ...................... 115

CONNECTING A Bluetooth®  iPod...................................................... 117
9
DEVICE............................................. 108 FILE INFORMATION ........................... 118
LISTENING TO Bluetooth® AUDIO ..... 108 TERMS ................................................ 121
ERROR MESSAGES........................... 122
5. AUX ................................................. 109
OVERVIEW ......................................... 109
69
1. BASIC OPERATION
1. QUICK REFERENCE
Press the “AUDIO” button to display the audio screen.

70
1. BASIC OPERATION
Function Page
Using the radio 77
Playing an audio CD or MP3/WMA/AAC disc 94
Playing a USB memory 97
Playing an iPod® 101

3
Playing a Bluetooth® device 105
AUDIO SYSTEM
Using the AUX port 109
Using the steering wheel audio switches 111
Audio system settings 112
71
1. BASIC OPERATION
2. SOME BASICS
This section describes some of the ba- TURNING THE SYSTEM ON

sic features of the audio system. Some AND OFF
information may not pertain to your
system.
Your audio system works when the en-
gine switch is turned to “ACC” or “ON”
position.
NOTICE
● To prevent the battery from being dis-
charged, do not leave the audio system
on longer than necessary when the
engine is not running.
“PWR·VOL” knob: Press to turn the audio
system on and off. The system turns on in
the last mode used. Turn this knob to ad-
CERTIFICATION
just the volume.
CAUTION: THIS PRODUCT IS A “AUDIO” button: Press to display screen
CLASS I LASER PRODUCT. USE OF buttons for the audio system.
CONTROLS OR ADJUSTMENTS OR
 A function that enables automatic return
PERFORMANCE OF PROCEDURES to the “Home” screen from the audio
OTHER THAN THOSE SPECIFIED screen can be selected. (P.56)
HEREIN MAY RESULT IN
HAZARDOUS RADIATION
EXPOSURE. DO NOT OPEN
COVERS AND DO NOT REPAIR BY
YOURSELF. REFER SERVICING TO
QUALIFIED PERSONNEL.
72
1. BASIC OPERATION
SELECTING AN AUDIO REORDERING THE AUDIO

SOURCE SOURCE
1 Press the “AUDIO” button.

1 Select “Reorder”.
AUDIO SYSTEM
2 Select the desired audio source then
or to reorder.
2 Select “Source” on the audio screen
or press “AUDIO” button again.
3 Select the desired source.
3 Select “OK”.
INFORMATION
ated.
● When there are two pages, select or
to change the page.
73
1. BASIC OPERATION
DISC SLOT USB/AUX PORT
1 Open the cover and connect a device.

INSERTING A DISC
1 Insert a disc into the disc slot.
 Turn on the power, if applicable, of the

device if it is not turned on.
 After insertion, the disc is automatically

loaded.
EJECTING A DISC
1 Press the button and remove the

disc.
NOTICE
● Never try to disassemble or oil any part

of the CD player. Do not insert anything
other than a disc into the slot.
INFORMATION
● The player is intended for use with 4.7
in. (12 cm) discs only.
● When inserting a disc, gently insert the
disc with the label facing up.
74
1. BASIC OPERATION
SOUND SETTINGS 1 Select “Sound” on the audio control

screen.
TONE AND BALANCE 2 Select the desired screen button.
TONE:
How good an audio program sounds is
3
largely determined by the mix of the
treble, mid and bass levels. In fact, dif-
AUDIO SYSTEM
ferent kinds of music and vocal pro-
grams usually sound better with
different mixes of treble, mid and bass.
BALANCE: No. Function
A good balance of the left and right ste- Select “+” or “-” to adjust high-
reo channels and of the front and rear pitched tones.
sound levels is also important. Select “+” or “-” to adjust mid-
Keep in mind that when listening to a pitched tones.
stereo recording or broadcast, chang-
Select “+” or “-” to adjust low-
ing the right/left balance will increase pitched tones.
the volume of 1 group of sounds while
decreasing the volume of another. Select to adjust the sound balance
between the front and rear speakers.
Select to adjust the sound balance

between the left and right speakers.
75
1. BASIC OPERATION
VOICE COMMAND SYSTEM
1 Press this switch to operate the voice

command system.
 The voice command system and its list

of commands can be operated.
(P.124)
76
2. RADIO OPERATION
1. AM/FM RADIO
OVERVIEW
Select “AM” or “FM” on the “Select Audio Source” screen. (P.73)
■CONTROL SCREEN
3
Top screen
AUDIO SYSTEM
Option screen
77
2. RADIO OPERATION

Top screen
Option screen
■CONTROL PANEL
78
2. RADIO OPERATION
No. Function
Select to scroll the page of preset buttons.
Select to display the option screen.
Select to display the audio source selection screen.

3
Select to display the cache radio operation buttons. (P.81)
AUDIO SYSTEM
Select to display the sound setting screen.
Cache radio only: Select to play/pause.
Select to display a list of receivable stations/channels.
Select to store information of the audio currently being broadcast on the radio.
Select to tune to preset stations/channels.
Select to display the additional text information.
Select to scan for receivable stations/channels.
Select to turn HD Radio mode on/off.

When the “HD Radio” indicator is off, the station list shows only analog broadcasts.
Analog FM only: Select to display RBDS text messages.
 Turn to step up/down frequencies.

 Turn to move up/down the list. Also, the knob can be used to enter selections on the
list screens by pressing it.
 Press to select a preset station.

 Press and hold to seek for a station.
 Turn to adjust volume.

 Press to turn the audio system on/off.
 Press and hold to restart the system.
INFORMATION
● The radio automatically changes to stereo reception when a stereo broadcast is received.
● The radio automatically blends to an HD Radio signal in AM or FM where available.
79
2. RADIO OPERATION
PRESETTING A STATION SELECTING A STATION

FROM THE LIST
Radio mode has a mix preset function,
which can store up to 36 stations (6 A station list can be displayed.
stations per page x 6 pages) from any
of the AM, FM or SAT bands. 1 Select “Station List”.
1 Tune in the desired station. 2 FM radio only: Select the desired pro-
gram genre.
2 Select “(add new)”.
3 Select the desired station and select

 To change the preset station to a different “OK”.
one, select and hold the preset station.
3 Select “Yes” on the confirmation
screen.
4 Select “OK” after setting the new pre-
set station.
INFORMATION
● The number of preset radio stations dis-
played on the screen can be changed.
(P.113)
80
2. RADIO OPERATION
■REFRESHING THE STATION LIST CACHING A RADIO

1 Select “Refresh” on the “Station List” PROGRAM (ENTUNE
screen and the following screen will be PREMIUM AUDIO ONLY)
displayed.
A radio program can be cached and
played back in a time-shifted manner.
3
PLAYING BACK THE CACHE
AUDIO SYSTEM
MANUALLY
The broadcast cached in the program

cache can be played back manually.
“Cancel Refresh”: Select to cancel the
refresh. 1 Select the desired cache radio opera-
“Source”: Select to change to another au- tion button.
dio source while refreshing.
INFORMATION
● AM/FM sound is muted during refresh
operation.
● In some situations, it may take some
time to update the station list.
No. Function
Hides the cache operation buttons
Skips backward 2 minutes
Select and hold: Fast rewinds con-

tinuously
Returns to the live radio broadcast
Select and hold: Fast forwards con-

tinuously
Skips forward 2 minutes
White dot: Shows what portion of the

cached broadcast is currently play-
ing
Light blue bar: Shows time in which
cache writing is in progress
81
2. RADIO OPERATION
AUTOMATIC PLAYBACK OF RADIO BROADCAST DATA

THE CACHE SYSTEM
If the radio broadcast is interrupted by
This audio system is equipped with Ra-
another audio output, such as an
dio Broadcast Data Systems (RBDS).
incoming phone call, the system will
RBDS mode allows text messages to
automatically cache the interrupted
be received from radio stations that uti-
portion and perform time-shift
lize RBDS transmitters.
playback when the interruption ends.
To manually operate the cache When RBDS is on, the radio can
operation: (P.81) — only select stations of a particular
program type,
— display messages from radio sta-
INFORMATION
tions,
● The system can store up to 20 minutes. — search for a stronger signal station.
Cached data will be erased when the
radio mode or station is changed or RBDS features are available only
when the audio system is turned off. when listening to an FM station that
● If noise or silence occurs during the broadcasts RBDS information and the
caching process, cache writing will con- “FM Info” indicator is on.
tinue, with the noise or silence recorded
as is. In this case, the cached broadcast
will contain the noise or silence when SELECTING A DESIRED
played back.
GENRE
1 Select “Station List”.
2 FM radio only: Select a desired genre

of station and select a desired station.
 The genre list is in the following order:
• Classical
• Country
• EasyLis (Easy Listening)
• Inform (Information)
• Jazz
• News
• Oldies
• Other
• Pop Music
• Religion
• Rock
• R&B (Rhythm and Blues)
• Sports
• Talk
• Traffic (Not available when “HD Radio”
indicator is off.)
• Alert (Emergency Alert)
82
2. RADIO OPERATION
TRAFFIC ANNOUNCEMENT USING HD Radio™

(FM RADIO) TECHNOLOGY
A station that regularly broadcasts traf- HD Radio™ Technology is the digital

fic information is automatically located. evolution of analog AM/FM radio. Your
radio product has a special receiver
1 Select “Station List”. which allows it to receive digital broad- 3
2 Select the desired traffic program sta- casts (where available) in addition to
the analog broadcasts it already re-
AUDIO SYSTEM
tion.
ceives. Digital broadcasts have better
INFORMATION sound quality than analog broadcasts
as digital broadcasts provide free,
● If a traffic program station is found, the
name of the traffic program station will crystal clear audio with no static or dis-
be displayed for a while. tortion. For more information, and a
guide to available radio stations and
programming, refer to 
www.hdradio.com.
HD Radio Technology manufactured

under license from iBiquity Digital
Corporation. U.S. and Foreign
Patents. HD Radio™ and the HD, HD
Radio, and “Arc” logos are proprietary
trademarks of iBiquity Digital Corp.
83
2. RADIO OPERATION
AVAILABLE HD Radio™ PRESERVING WITH MUSIC

TECHNOLOGY INFORMATION
Tag information in the music broad-

MULTICAST casting is preserved in the system can
be transferred to an iPod.
On the FM radio frequency most digital
stations have “multiple” or supplemen- 1 Select “Tag” to bookmark the music
tal programs on one FM station. information.
1 Select “HD)” logo.
2 Connect an iPod. (P.74)

 Turn on the power of the iPod if it is not
2 Select the desired channel. turned on.
 Turning the “TUNE·SCROLL” knob can  Once an iPod is connected, the music tag
also select the desired multicast channel. moves from the radio into the iPod.
 When the iPod is connected to iTunes, the
“tagged” information of the songs which
were tagged while listening to the radio
can be viewed with an option to purchase.
84
2. RADIO OPERATION
INFORMATION
● The tag information cannot be preserved
while scanning or caching the radio sta-
tion.
● If tagging the music information fails,
“Saving the HD Radio tag was unsuc-
cessful.” will be displayed on the screen.
If this occurs, tag the information again. 3
● HD Radio™ stations can saved as pre-
sets.
AUDIO SYSTEM
● An orange “HD)” logo indicator will be
displayed on the screen when in digital.
The “HD)” logo will first appear in a gray
color indicating the station is indeed (an
analog and) a digital station. Once the
digital signal is acquired, the logo will
change to a bright orange color.
● The song title, artist name and music
genre will appear on the screen when
available by the radio station. The radio
station can send album pictures when
available with HD is available.
● As a user works through the analog
radio stations, (where applicable) the
radio receiver will automatically tune
from an analog signal to a digital signal
within 5 seconds.
85
2. RADIO OPERATION
TROUBLESHOOTING GUIDE
Experience Cause Action
Mismatch of time align-

The radio stations analog
ment- a user may hear a
and digital volume is not None, radio broadcast issue. A
short period of program-
properly aligned or the sta- user can contact the radio station.
ming replayed or an echo,
tion is in ballgame mode.
stutter or skip.
Reception issue, may clear-up as

the vehicle continues to be driven.
Sound fades, blending in Radio is shifting between
Turning the indicator of the “HD
and out. analog and digital audio.
Radio” button off can force radio in
an analog audio.
This is normal behavior, wait until

Audio mute condition when The radio does not have
the digital signal returns. If out of
an HD2/HD3 multicast access to digital signals at
the coverage area, seek a new
channel had been playing. the moment.
station.
The digital multicast con-

tent is not available until
Audio mute delay when se-
HD Radio™ broadcast can This is normal behavior, wait for
lecting an HD2/HD3 multi-
be decoded and make the the audio to become available.
cast channel preset.
audio available. This takes
up to 7 seconds.
Broadcaster should be notified.

Text information does not
Data service issue by the Complete the form; 
match the present song au-
radio broadcaster. www.ibiquity.com/automotive/
dio.
report_radio_station_experiences.
Broadcaster should be notified.

No text information shown
Data service issue by the Complete the form; 
for the present selected fre-
radio broadcaster. www.ibiquity.com/automotive/
quency.
report_radio_station_experiences.
86
2. RADIO OPERATION
2. XM Satellite Radio*
OVERVIEW
Select “XM” on the “Select Audio Source” screen. (P.73)
■CONTROL SCREEN
3
AUDIO SYSTEM
■CONTROL PANEL
*: If equipped
87
2. RADIO OPERATION
No. Function
Select to scroll the page of preset buttons.
Select to display the option screen.

 Select to scan for receivable channels.
 Select “Additional Information” to display the information.
Select to display the “Select Audio Source” screen.
Select to display a list of receivable channels.
Select to tune to preset stations/channels.
 Turn to step up/down channels.

 Press to seek for a channel.

 Press and hold to seek continuously.

 Press and hold to restart the audio system.
88
2. RADIO OPERATION
HOW TO SUBSCRIBE TO XM NOTICE

Satellite Radio
● XM Radio ServicesLegal Disclaimers
and Warnings
To listen to a satellite radio broadcast
• Fees and TaxesSubscription fee,
in the vehicle, a subscription to the XM taxes, one time activation fee, and
Satellite Radio service is necessary. other fees may apply. Subscription fee
An XM Satellite Radio is a tuner de- is consumer only. All fees and pro- 3
gramming subject to change.
signed exclusively to receive broad- Subscriptions subject to Customer
AUDIO SYSTEM
casts provided under a separate Agreement available at www.siri-
subscription. Availability is limited to usxm.com. (U.S.A.) or www.xmra-
the 48 contiguous U.S. states and dio.ca (Canada) XM service only
some Canadian provinces. available in the 48 contiguous United
States and Canada.
Explicit Language NoticeChannels
HOW TO SUBSCRIBE with frequent explicit language are indi-
cated with an “XL” preceding the chan-
nel name. Channel blocking is
It is necessary to enter into a separate available for XM Satellite Radio receiv-
service agreement with XM Satellite ers by notifying XM at;
Radio in order to receive satellite U.S.A. Customers:
broadcast programming in the vehicle. Visit www.siriusxm.com or calling 
Additional activation and service sub- 1-800-967-2346
Canadian Customers:
scription fees apply that are not includ- Visit www.xmradio.ca or calling 
ed in the purchase price of the vehicle 1-877-209-0079
and digital satellite tuner. ● It is prohibited to copy, decompile, disas-
semble, reverse engineer, hack, manip-
 For complete information on subscrip- ulate, or otherwise make available any
tion rates and terms, or to subscribe to technology or software incorporated in
XM Satellite Radio: receivers compatible with the XM Satel-
lite Radio System or that support the XM
 U.S.A. website, the Online Service or any of its
Refer to www.siriusxm.com or call  content. Furthermore, the AMBE® voice
1-800-967-2346. compression software included in this
product is protected by intellectual prop-
Canada erty rights including patent rights, copy-
Refer to www.xmradio.ca or call  rights, and trade secrets of Digital Voice
1-877-209-0079. Systems, Inc.
● Note: this applies to XM receivers only
and not XM Ready devices.
89
2. RADIO OPERATION
INFORMATION INFORMATION
● XM Radio ServicesDescriptions ● XM Satellite Radio is solely responsible
• Radio and Entertainment for the quality, availability and content of
XM offers more than 170 satellite radio the satellite radio services provided,
channels of commercial-free music which are subject to the terms and con-
and premier sports, news, talk, and ditions of the XM Satellite Radio cus-
entertainment. XM is broadcast via sat- tomer service agreement.
ellites to millions of listeners across the ● Customers should have their radio ID
continental United States. XM sub- ready; the radio ID can be found by tun-
scribers listen to XM on satellite radio ing to “Ch 000” on the radio. For details,
receivers for the car, home, and porta- see “DISPLAYING THE RADIO ID”
ble use. More information about XM is below.
available online at www.siriusxm.com ● All fees and programming are the
(U.S.A.) or www.xmradio.ca (Canada). responsibility of XM Satellite Radio and
● XM Radio ServicesSubscription are subject to change.
Instructions
• For XM Services requiring a subscrip-
tion (such as XM Radio, and some SATELLITE TUNER
Infotainment & data services), the fol-
TECHNOLOGY NOTICE
lowing paragraph shall be included.
Required XM Radio and some Infotain-
ment & data services monthly sub- Toyota’s satellite radio tuners are
scriptions sold separately after trial awarded Type Approval Certificates
period. Subscription fee is consumer from XM Satellite Radio Inc. as proof of
only. All fees and programming subject compatibility with the services offered
to change. Subscriptions are subject to
the Customer Agreement available at by XM Satellite Radio.
www.siriusxm.com. XM service only
available in the 48 contiguous United INFORMATION
States.  2011 Sirius XM Radio Inc.
Sirius, XM and all related marks and ● Satellite tuner
logos are trademarks of Sirius XM The tuner supports only Audio Services
Radio Inc. All other marks, channel (Music and Talk) and the accompanying
names and logos are the property of Text Information of XM® Satellite Radio.
their respective owners.
For more information, program sched-
ules, and to subscribe or extend sub-
scription after complimentary trial
period; more information is available
at:
USA Customers:
Visit www.siriusxm.com or call 
1-866-635-2349
90
2. RADIO OPERATION
DISPLAYING THE RADIO ID SELECTING A CHANNEL

FROM THE LIST
Each XM tuner is identified with a
unique radio ID. The radio ID is re- 1 Select “Channel List”.
quired when activating an XM service
or when reporting a problem.
2 Select the desired program genre.
 If “Ch 000” is selected using the 3 Select the desired channel and select 3
“TUNE·SCROLL” knob, the ID code, “OK”.
which is 8 alphanumeric characters, will
AUDIO SYSTEM
be displayed. If another channel is
selected, the ID code will no longer be dis-
played. The channel (000) alternates
between displaying the radio ID and the
specific radio code.
PRESETTING A CHANNEL
1 Tune in the desired channel.
2 Select “(add new)”.
 To change the preset channel to a differ-

ent one, select and hold the preset station/
channel.
3 Select “Yes” on the confirmation
screen.
4 Select “OK” after setting the new pre-
set channel.
91
2. RADIO OPERATION
IF THE SATELLITE RADIO TUNER MALFUNCTIONS
When problems occur with the XM tuner, a message will appear on the screen. Re-
ferring to the table below to identify the problem, take the suggested corrective ac-
tion.
Message Explanation
The XM antenna is not connected. Check whether the XM antenna

cable is attached securely.
“Check Antenna”
A short circuit occurs in the antenna or the surrounding antenna ca-
ble. See a Toyota certified dealer for assistance.
You have not subscribed to XM Satellite Radio. The radio is being

updated with the latest encryption code. Contact XM Satellite Radio
for subscription information. When a contract is canceled, you can
choose “Ch 000” and all free-to-air channels.
“Ch Unauthorized”
The premium channel you selected is not authorized. Wait for about
2 seconds until the radio returns to the previous channel or “Ch 001”.
If it does not change automatically, select another channel. To listen
to the premium channel, contact XM Satellite Radio.
The XM signal is too weak at the current location. Wait until your ve-
“No Signal”
hicle reaches a location with a stronger signal.
The unit is acquiring audio or program information. Wait until the unit
“Loading”
has received the information.
The channel you selected is not broadcasting any programming. Se-

“Channel Off Air”
lect another channel.
There is no song/program title or artist name/feature associated with

-----
the channel at that time. No action is required.
The channel you selected is no longer available. Wait for about 2

“Chan Unavailable” seconds until the radio returns to the previous channel or “Ch 001”.
If it does not change automatically, select another channel.
INFORMATION
● Contact the XM Listener Care Center at 1-800-967-2346 (U.S.A.) or 1-877-209-0079
(Canada).
92
2. RADIO OPERATION
3. INTERNET RADIO*
LISTENING TO INTERNET INFORMATION

RADIO ● Other applications can be activated
while listening to internet radio.
One of Entune App Suite features is ● Some parts of applications can be
the ability to listen to internet radio. In adjusted using the switches on the
steering wheel.
order to use this service, a compatible
● For additional information, refer to 
phone and the system need to be set http://www.toyota.com/entune/ or call  3
up. For details: P.261 1-800-331-4331.
AUDIO SYSTEM
2 Select the internet radio application.
 The internet radio application screen is

displayed.
 Perform operations according to the dis-
played application screen.
 If a compatible phone is already regis-
tered, it will be connected automatically.

93
3. MEDIA OPERATION
1. CD
OVERVIEW
The CD operation screen can be reached by the following methods:

Insert a disc (P.74)
Select “CD” on the “Select Audio Source” screen. (P.73)
■CONTROL SCREEN
■CONTROL PANEL
94
3. MEDIA OPERATION
No. Function
 Displays cover art

 Select to display a track/file list.

3
Select to play/pause.
AUDIO SYSTEM
Shows progress
Select to set repeat playback.
Select to set random playback.
 Audio CD: Select to display a track list.

 MP3/WMA/AAC disc: Select to display a folder list. 
To return to the top screen, select “Now Playing” on the list screen.
Disc slot
 Turn to select a track/file.

 Press to select a track/file.

 Press and hold to fast forward/rewind.

Press to eject a disc.
INFORMATION
● If a disc contains CD-DA files and MP3/WMA/AAC files, only the CD-DA files can be
played back.
● If a CD-TEXT disc is inserted, the title of the disc and track will be displayed. Up to 32
characters can be displayed.
● If the disc contains no CD-TEXT, only the track number would be displayed on the
screen.
95
3. MEDIA OPERATION
PLAYING AN AUDIO CD PLAYING AN MP3/WMA/AAC

DISC
REPEATING
REPEATING
The track currently being listened to
can be repeated. The file or folder currently being lis-
tened to can be repeated.
1 Select the repeat button to change on/
off. 1 Select the repeat button to change on/
off.
RANDOM ORDER
RANDOM ORDER
Tracks can be automatically and ran-
domly selected. Files or folders can be automatically
and randomly selected.
1 Select the random button to change
on/off. 1 Select the random button to change
on/off.
96
3. MEDIA OPERATION
2. USB MEMORY
OVERVIEW
The USB memory operation screen can be reached by the following methods:
Connect a USB memory (P.74)
Select “USB” on the “Select Audio Source” screen. (P.73)
3
■CONTROL SCREEN
AUDIO SYSTEM
■CONTROL PANEL
97
3. MEDIA OPERATION
No. Function
Shows progress
Select to display the play mode selection screen. 

 Displays cover art.

 Select to display file/track list.
 Turn to select a track/file.

 Press to select a track/file.


98
3. MEDIA OPERATION
CAUTION
● Do not operate the player’s controls or connect the USB memory while driving.
NOTICE
● Do not leave your portable player in the car. In particular, high temperatures inside the 3
vehicle may damage the portable player.
● Do not push down on or apply unnecessary pressure to the portable player while it is con-
AUDIO SYSTEM
nected as this may damage the portable player or its terminal.
● Do not insert foreign objects into the port as this may damage the portable player or its
terminal.
INFORMATION
● If tag information exists, the file names will be changed to track names.
99
3. MEDIA OPERATION
PLAYING A USB AUDIO
REPEATING
The file/track currently being listened

to can be repeated.

off.
RANDOM ORDER
Files/tracks can be automatically and

randomly selected.

on/off.
100
3. MEDIA OPERATION
3. iPod
OVERVIEW
The iPod operation screen can be reached by the following methods:

Connect an iPod (P.74)
Select “iPod” on the “Select Audio Source” screen. (P.73)
When the iPod connected to the system includes iPod video, the system can only 3
output the sound by selecting the browse screen.
AUDIO SYSTEM
■CONTROL SCREEN
101
3. MEDIA OPERATION
■CONTROL PANEL
No. Function
 Displays cover art

 Select to display a track list.
Shows progress
Select to display the play mode selection screen.

 Turn to select a track.

 Press to select a track.


102
3. MEDIA OPERATION
CAUTION
● Do not operate the player’s controls or connect the iPod while driving.
NOTICE
● Do not leave your portable player in the car. In particular, high temperatures inside the 3
vehicle may damage the portable player.
● Do not push down on or apply unnecessary pressure to the portable player while it is con-
AUDIO SYSTEM
nected as this may damage the portable player or its terminal.
● Do not insert foreign objects into the port as this may damage the portable player or its
terminal.
INFORMATION
● When an iPod is connected using a genuine iPod cable, the iPod starts charging its bat-
tery.
● Depending on the iPod and the songs in the iPod, iPod cover art may be displayed. This
function can be changed to on/off. (P.112) It may take time to display iPod cover art,
and the iPod may not be operated while the cover art display is in process.
● When an iPod is connected and the audio source is changed to iPod mode, the iPod will
resume playing from the same point it was last used.
● Depending on the iPod that is connected to the system, certain functions may not be
available.
● Files/tracks selected by operating a connected iPod may not be recognized or displayed
properly.
● If an iPhone is connected via Bluetooth® and USB at the same time, system operation
may become unstable.
For known phone compatibility information, refer to http://www.toyota.com/entune/.
103
3. MEDIA OPERATION
PLAYING AN iPod
REPEATING
The track currently being listened to

can be repeated.

off.
RANDOM ORDER
Tracks can be automatically and ran-

domly selected.
1 Select the shuffle button to change on/

off.
104
3. MEDIA OPERATION
4. Bluetooth® AUDIO
The Bluetooth® audio system enables users to enjoy listening to music that is
played on a portable player on the vehicle speakers via wireless communication.
This audio system supports Bluetooth®, a wireless data system capable of playing
portable audio music without cables. If your device does not support Bluetooth®,
the Bluetooth® audio system will not function.
3
OVERVIEW
AUDIO SYSTEM
Select “ Audio” on the “Select Audio Source” screen. (P.73)
Depending on the type of portable player connected, some functions may not be
available and/or the screen may look differently than shown in this manual.
■CONTROL SCREEN
105
3. MEDIA OPERATION
■CONTROL PANEL
No. Function
Displays Bluetooth® device condition.
Shows progress
Select to display the sound settings screen.
Select to display the play mode selection screen. 

Select to display the portable device connection screen.
 Displays cover art.

 Select to display a track list.
 Turn to select a track.

 Press to select a track.


106
3. MEDIA OPERATION
CAUTION
● Do not operate the player’s controls or connect to the Bluetooth® audio system while driv-
ing.
● Your audio unit is fitted with Bluetooth® antennas. People with implantable cardiac pace-
makers, cardiac resynchronization therapy-pacemakers or implantable cardioverter
defibrillators should maintain a reasonable distance between themselves and the Blue-
tooth® antennas. The radio waves may affect the operation of such devices. 3
● Before using Bluetooth® devices, users of any electrical medical device other than
AUDIO SYSTEM
implantable cardiac pacemakers, cardiac resynchronization therapy-pacemakers or
implantable cardioverter defibrillators should consult the manufacturer of the device for
information about its operation under the influence of radio waves. Radio waves could
have unexpected effects on the operation of such medical devices.
NOTICE
● Do not leave your portable player in the vehicle. In particular, high temperatures inside
the vehicle may damage the portable player.
INFORMATION
● Depending on the Bluetooth® device that is connected to the system, the music may start
playing when selecting while it is paused. Conversely, the music may pause when
selecting while it is playing.

● In the following conditions, the system may not function:
• The Bluetooth® device is turned off.
• The Bluetooth® device is not connected.
• The Bluetooth® device has a low battery.
● It may take time to connect the phone when Bluetooth® audio is being played.
● For operating the portable player, see the instruction manual that comes with it.
● If the Bluetooth® device is disconnected due to poor reception from the Bluetooth® net-
work when the engine switch is turned to the “ACC” or “ON” position, the system auto-
matically reconnects the portable player.
● If the system is attempting to connect to a Bluetooth® device and the Bluetooth® device is
turned off and then back on, the system will attempt to reconnect.
● Bluetooth® device information is registered when the Bluetooth® device is connected to
the Bluetooth® audio system. When selling or disposing of the vehicle, remove the
Bluetooth® audio information from the system. (P.60)
107
3. MEDIA OPERATION
CONNECTING A Bluetooth® LISTENING TO Bluetooth®

DEVICE AUDIO
To use the Bluetooth® audio system, it REPEATING

is necessary to register a Bluetooth®
device with the system. The track or album currently being lis-
tened to can be repeated.
Registering an additional device
1 Select “Select Device” on the
off.
Bluetooth® audio control screen.
2 For more information: P.50 RANDOM ORDER
Selecting a registered device
Tracks or albums can be automatically
1 Select “Select Device” on the and randomly selected.
Bluetooth® audio control screen.
2 For more information: P.51 on/off.
108
3. MEDIA OPERATION
5. AUX
OVERVIEW
Select “AUX” on the “Select Audio Source” screen. (P.73)
■CONTROL SCREEN
3
AUDIO SYSTEM
■CONTROL PANEL
109
3. MEDIA OPERATION
No. Function

CAUTION
● Do not connect portable audio device or operate the controls while driving.
NOTICE
● Do not leave portable audio device in the vehicle. The temperature inside the vehicle may
become high, resulting in damage to the player.
● Do not push down on or apply unnecessary pressure to the portable audio device while it
is connected as this may damage the portable audio device or its terminal.
● Do not insert foreign objects into the port as this may damage the portable audio device
or its terminal.
110
4. AUDIO REMOTE CONTROLS
1. STEERING SWITCHES
Some parts of the audio system can be “ ” switch

adjusted using the switches on the When in radio mode
steering wheel.
 Press the “ ” or “ ” switch to change
the station/channel up or down.
 Press and hold the “ ” or “ ” switch to
type seek up or down. (XM Satelite Radio)
When in media mode 3
 Press the “ ” or “ ” switch to skip to the
next or previous track/file.
AUDIO SYSTEM
fast skip to the next or previous track/file.
fast forward or rewind.
No. Switch When in a list screen of media mode

 Press the “ ” or “ ” switch to scroll up
Volume control switch or down the items.
Back switch skip to the next or previous page.
“ ” switch change the playlist tab. (iPod, USB)
Enter switch Enter switch

When in media mode
“MODE/HOLD” switch  Press the enter switch to show the list
screen.
Volume control switch When in a list screen of media mode
 Press the “+” side to increase the volume.  Enter the selected item.
The volume continues to increase while
the switch is being pressed. “MODE/HOLD” switch
 Press the “-” side to decrease the vol-  Press the “MODE/HOLD” switch to select
ume. The volume continues to decrease an audio mode. Each press changes the
while the switch is being pressed. mode sequentially if the desired mode is
ready to use.
Back switch  To turn the audio system on, press the
 Press the back switch to return to the pre- “MODE/HOLD” switch.
vious screen.  Press and hold the “MODE/HOLD” switch
to mute or pause the current operation.
111
5. SETUP
1. AUDIO SETTINGS
Detailed audio settings can be pro- “Audio Settings” SCREEN

grammed.
No. Function Page
Select to change the num-

ber of preset radio stations 113
2 Select “Setup”. displayed on the screen.
3 Select to set cover art set-

Select “Audio”. 
tings.
Select to set automatic
113
sound levelizer.
Select to set the surround

*1 
function on/off.
Select to enable cache ra-

*2 
dio.
*1: Entune Premium JBL Audio only

112
5. SETUP
SETTING THE NUMBER OF

RADIO PRESETS
1 Display the “Audio Settings” screen.

(P.112)
2 Select “Number of Radio Presets”.
3
3 Select the button with the desired num-
ber to be displayed.
AUDIO SYSTEM
AUTOMATIC SOUND
LEVELIZER (ASL)
The system adjusts to the optimum vol-

ume and tone quality according to ve-
hicle speed to compensate for
increased vehicle noise.
1 Display the “Audio Settings” screen.

(P.112)
2 Select the “Automatic Sound Level-
izer”.
3 Select the “High”, “Mid”, “Low”, or
“Off”.
Entune Premium JBL Audio
3 Select on/off.
113
6. TIPS FOR OPERATING THE AUDIO SYSTEM
1. OPERATING INFORMATION
NOTICE FM
Fading and drifting stations: Generally, the
● To avoid damage to the audio system:
effective range of FM is about 25 miles (40
• Be careful not to spill beverages over
the audio system. km). Once outside this range, you may no-
• Do not put anything other than an tice fading and drifting, which increase with
appropriate disc into the disc slot. the distance from the radio transmitter.
They are often accompanied by distortion.
Multi-path: FM signals are reflective, mak-
INFORMATION ing it possible for 2 signals to reach the ve-
● The use of a cellular phone inside or hicle’s antenna at the same time. If this
near the vehicle may cause a noise from happens, the signals will cancel each other
the speakers of the audio system which out, causing a momentary flutter or loss of
you are listening to. However, this does reception.
not indicate a malfunction.
Static and fluttering: These occur when
signals are blocked by buildings, trees or
other large objects. Increasing the bass
RADIO level may reduce static and fluttering.
Station swapping: If the FM signal being
Usually, a problem with radio reception
listened to is interrupted or weakened, and
does not mean there is a problem with there is another strong station nearby on
the radio — it is just the normal result the FM band, the radio may tune in the
of conditions outside the vehicle. second station until the original signal can
For example, nearby buildings and ter- be picked up again.
rain can interfere with FM reception.
Power lines or phone wires can inter- AM
fere with AM signals. And of course, ra-
dio signals have a limited range. The Fading: AM broadcasts are reflected by
farther the vehicle is from a station, the the upper atmosphere — especially at
weaker its signal will be. In addition, re- night. These reflected signals can interfere
ception conditions change constantly with those received directly from the radio
station, causing the radio station to sound
as the vehicle moves.
alternately strong and weak.
Here, some common reception prob-
Station interference: When a reflected sig-
lems that probably do not indicate a nal and a signal received directly from a ra-
problem with the radio are described. dio station are very nearly the same
frequency, they can interfere with each
other, making it difficult to hear the broad-
cast.
Static: AM is easily affected by external
sources of electrical noise, such as high
tension power lines, lightening or electrical
motors. This results in static.
114
XM
 Cargo loaded on the roof luggage carrier,
especially metal objects, may adversely Audio CDs
affect the reception of XM Satellite Radio.
 Alternation or modifications carried out
without appropriate authorization may
invalidate the user’s right to operate the
equipment.  Use only discs marked as shown above. 3
The following products may not be play-
able on your player:
AUDIO SYSTEM
CD PLAYER AND DISC • SACD
• dts CD
 This CD player is intended for use with 4.7 • Copy-protected CD
in. (12 cm). discs only. • Video CD
 Extremely high temperatures can keep the
CD player from working. On hot days, use
the air conditioning system to cool the
inside of the vehicle before using the
player.
 Bumpy roads or other vibrations may
make the CD player skip.
 If moisture gets into the CD player, the
discs may not be able to be played.
Remove the discs from the player and
wait until it dries.
CAUTION
● CD players use an invisible laser beam

which could cause hazardous laser radi-
ation exposure if directed outside the
unit. Be sure to operate the player cor-
rectly.
115
Special shaped discs

NOTICE
● Do not use special shaped, transparent/
translucent, low quality or labeled discs
such as those shown in the illustrations.
The use of such discs may damage the
player, or it may be impossible to eject
the disc.
● This system is not designed for use of
Dual Discs. Do not use Dual Discs
because they may cause damage to the
player.
Transparent/translucent discs ● Do not use discs with a protection ring.
The use of such discs may damage the
player, or it may be impossible to eject
the disc.
● Do not use printable discs. The use of
such discs may damage the player, or it
may be impossible to eject the disc.
Low quality discs
Correct Wrong
 Handle discs carefully, especially when

inserting them. Hold them on the edge
and do not bend them. Avoid getting fin-
gerprints on them, particularly on the shiny
side.
Labeled discs  Dirt, scratches, warping, pin holes or other
disc damage could cause the player to
skip or to repeat a section of a track. (To
see a pin hole, hold the disc up to the
light.)
 Remove discs from the players when not
in use. Store them in their plastic cases
away from moisture, heat and direct sun-
light.
116
iPod
AUDIO SYSTEM
 “Made for iPod” and “Made for iPhone”
To clean a disc: Wipe it with a soft, lint- mean that an electronic accessory has
free cloth that has been dampened with been designed to connect specifically to
water. Wipe in a straight line from the cen- iPod or iPhone respectively, and has been
certified by the developer to meet Apple
ter to the edge of the disc (not in circles). performance standards.
Dry it with another soft, lint-free cloth. Do  Apple is not responsible for the operation
not use a conventional record cleaner or of this device or its compliance with safety
anti-static device. and regulatory standards. Please note
that the use of this accessory with iPod or
iPhone may affect wireless performance.
CD-R/RW DISCS
 iPhone, iPod, iPod classic, iPod nano, and
 CD-R/CD-RW discs that have not been iPod touch are trademarks of Apple Inc.,
subject to the “finalizing process” (a pro- registered in the U.S. and other countries.
cess that allows discs to be played on a Lightning is a trademark of Apple Inc.
conventional CD player) cannot be
played.
 It may not be possible to play CD-R/CD-
RW discs recorded on a music CD
recorder or a personal computer because
of disc characteristics, scratches or dirt on
the disc, or dirt, condensation, etc. on the
lens of the unit.
 It may not be possible to play discs
recorded on a personal computer depend-
ing on the application settings and the
environment. Record with the correct for-
mat. (For details, contact the appropriate
application manufacturers of the applica-
tions.)
 CD-R/CD-RW discs may be damaged by
direct exposure to sunlight, high tempera-
tures or other storage conditions. The unit
may be unable to play some damaged
discs.
 If you insert a CD-RW disc into the player,
playback will begin more slowly than with
a conventional CD or CD-R disc.
 Recordings on CD-R/CD-RW cannot be
played using the DDCD (Double Density
CD) system.
117
COMPATIBLE MODELS FILE INFORMATION

The following iPod®, iPod nano®, iPod
■COMPATIBLE USB DEVICES
classic®, iPod touch® and iPhone® devic-
es can be used with this system. USB 2.0 HS (480
USB communication
Made for formats
Mbps) and FS
• iPod touch (5th generation) (12 Mbps)
• iPod touch (4th generation)
• iPod touch (3rd generation) File formats FAT 16/32
• iPod touch (2nd generation)
Mass storage
• iPod touch (1st generation) Correspondence class
class
• iPod classic
• iPod with video
• iPod nano (7th generation) ■COMPATIBLE COMPRESSED
• iPod nano (6th generation) FILES
• iPod nano (5th generation)
• iPod nano (4th generation)
Item USB DISC
• iPod nano (3rd generation)
• iPhone 6 Plus Compatible
• iPhone 6 MP3/WMA/AAC
file format
• iPhone 5S
• iPhone 5C Folders in the Maximum Maximum
• iPhone 5 device 3000 192
• iPhone 4S
• iPhone 4 Files in the Maximum Maximum
• iPhone 3GS device 9999 255
• iPhone 3G
• iPhone Files per  Maximum

Depending on differences between mod- folder 255
els or software versions etc., some models
might be incompatible with this system.
118
■CORRESPONDING SAMPLING  MP3 (MPEG Audio Layer 3), WMA

FREQUENCY (Windows Media Audio) and AAC
(Advanced Audio Coding) are audio com-
pression standards.
File type Frequency (kHz)
 This system can play MP3/WMA/AAC files
MP3 files:  on CD-R, CD-RW discs and USB memory.
32/44.1/48  This system can play disc recordings com-
MPEG 1 LAYER 3
patible with ISO 9660 level 1 and level 2
MP3 files:  and with the Romeo and Joliet file system. 3
16/22.05/24
MPEG 2 LSF LAYER 3  When naming an MP3/WMA/AAC file, add
an appropriate file extension (.mp3/.wma/
AUDIO SYSTEM
WMA files: 
32/44.1/48 .m4a).
Ver. 7, 8, 9 (9.1/9.2)
 This system plays back files with .mp3/
11.025/12/16/ .wma/.m4a file extensions as MP3/WMA/
AAC files:  AAC files respectively. To prevent noise
22.05/24/32/
MPEG4/AAC-LC and playback errors, use the appropriate
44.1/48
file extension.
 This system can play only the first session
■CORRESPONDING BIT RATES when using multi-session compatible CDs.
 MP3 files are compatible with the ID3 Tag
File type Bit rate (kbps) Ver. 1.0, Ver. 1.1, Ver. 2.2 and Ver. 2.3 for-
mats. This system cannot display disc
MP3 files:
32 - 320 title, track title and artist name in other for-
MPEG 1 LAYER 3
mats.
MP3 files:  WMA/AAC files can contain a WMA/AAC
8 - 160 tag that is used in the same way as an ID3
MPEG 2 LSF LAYER 3
tag. WMA/AAC tags carry information
WMA files: Ver. 7, 8 CBR 48 - 192 such as track title and artist name.
 The emphasis function is available only
WMA files:
CBR 48 - 320 when playing MP3/WMA files recorded at
Ver. 9 (9.1/9.2) 32, 44.1 and 48 kHz.
AAC files:  This system can play back AAC files
16 - 320 encoded by iTunes.
MPEG4/AAC-LC
 The sound quality of MP3/WMA files gen-
(Variable Bit Rate (VBR) compatible) erally improves with higher bit rates. In
order to achieve a reasonable level of
sound quality, discs recorded with a bit
rate of at least 128 kbps are recom-
mended.
 The MP3/WMA player does not play back
MP3/WMA files from discs recorded using
packet write data transfer (UDF format).
Discs should be recorded using “pre-mas-
tering” software rather than packet-write
software.
 M3u playlists are not compatible with the
audio player.
 MP3i (MP3 interactive) and MP3PRO for-
mats are not compatible with the audio
player.
119
 The player is compatible with VBR (Vari-

able Bit Rate).
 When playing back files recorded as VBR
001.mp3
(Variable Bit Rate) files, the play time will 002.wma
not be correctly displayed if the fast for- Folder 1
ward or rewind operations are used. 003.mp3
 It is not possible to check folders that do Folder 2
not include MP3/WMA/AAC files. 004.mp3
005.wma
 MP3/WMA/AAC files in folders up to 8 lev- Folder 3
els deep can be played. However, the 006.m4a
start of playback may be delayed when
using discs containing numerous levels of
 The play order of the compact disc with
folders. For this reason, we recommend
the structure shown above is as follows:
creating discs with no more than 2 levels
of folders.
001.mp3 002.wma . . . 006.m4a
 The order changes depending on the per-

sonal computer and MP3/WMA/AAC
encoding software you use.
120
TERMS MP3
 MP3 is an audio compression standard
PACKET WRITE determined by a working group (MPEG) of
the ISO (International Standard Organiza-
 This is a general term that describes the tion). MP3 compresses audio data to
process of writing data on-demand to CD- about 1/10 the size of that on conventional
R, etc., in the same way that data is writ- discs.
ten to floppy or hard discs. 3
WMA
AUDIO SYSTEM
ID3 TAG
 WMA (Windows Media Audio) is an audio
 This is a method of embedding track- compression format developed by
related information in an MP3 file. This Microsoft®. It compresses files into a size
embedded information can include the smaller than that of MP3 files. The decod-
track number, track title, the artist’s name, ing formats for WMA files are Ver. 7, 8 and
the album title, the music genre, the year 9. This product is protected by certain
of production, comments, cover art and intellectual property rights of Microsoft
other data. The contents can be freely Corporation and third parties. Use or dis-
edited using software with ID3 tag editing tribution of such technology outside of this
functions. Although the tags are restricted product is prohibited without a license
to a number of characters, the information from Microsoft or an authorized Microsoft
can be viewed when the track is played subsidiary and third parties.
back.
AAC
WMA TAG
 AAC is short for Advanced Audio Coding
 WMA files can contain a WMA tag that is and refers to an audio compression tech-
used in the same way as an ID3 tag. WMA nology standard used with MPEG2 and
tags carry information such as track title MPEG4.
and artist name.
ISO 9660 FORMAT

 This is the international standard for the
formatting of CD-ROM folders and files.
For the ISO 9660 format, there are 2 lev-
els of regulations.
 Level 1: The file name is in 8.3 format (8
character file names, with a 3 character
file extension. File names must be com-
posed of one-byte capital letters and num-
bers. The “_” symbol may also be
included.)
 Level 2: The file name can have up to 31
characters (including the separation mark
“.” and file extension). Each folder must
contain fewer than 8 hierarchies.
121
ERROR MESSAGES
Mode Message Explanation
This indicates that no MP3/WMA/AAC files are

“No music files found.”
included in the DISC.
It indicates that the disc is dirty, damaged, or it

was inserted upside down. Clean the disc or in-
CD “Check Disc” sert it correctly.
It indicates a disc which is not playable is insert-
ed.
There is a trouble inside the system.

“Disc Error”
Eject the disc.
“Connection error. Please

consult your Owner’s
This indicates a problem in the USB memory or
Manual for instructions on
its connection.
how to connect the USB
USB device.”
“There are no files avail-

able for playback. Please This indicates that no MP3/WMA/AAC files are
add compatible files to included in the USB memory.
your USB device.”
“Connection error. Please

consult your Owner’s This indicates a problem in the iPod or its con-
Manual for instructions on nection.
how to connect the iPod.”
“There are no songs avail-

iPod
able for playback. Please This indicates that there is no music data in the
add compatible files to iPod.
your iPod.”
“iPod authorization unsuc- This indicates that it failed to authorize the iPod.
cessful.” Please check your iPod.
INFORMATION
● If the malfunction is not rectified: Take your vehicle to your Toyota dealer.
122
4
1
2
VOICE COMMAND SYSTEM  3

1
OPERATION
1. VOICE COMMAND SYSTEM...... 124 4

USING THE VOICE COMMAND 
SYSTEM............................................ 124
VOICE COMMAND SYSTEM  5
OPERATION ..................................... 125
2. CASUAL SPEECH 6
RECOGNIZATION..................... 129
3. COMMAND LIST ......................... 130

7
MOBILE ASSISTANT
2 8
OPERATION
1. MOBILE ASSISTANT.................. 132

9
123
1. VOICE COMMAND SYSTEM OPERATION
1. VOICE COMMAND SYSTEM
The voice command system enables MICROPHONE

the navigation, audio and hands-free
systems to be operated using voice
commands.
Refer to the command list for samples
of voice commands. (P.130)
USING THE VOICE

COMMAND SYSTEM
STEERING SWITCH  It is unnecessary to speak directly into the

microphone when giving a command.
INFORMATION
● The voice command system can be
operated while guidance is being spo-
ken. (It is not necessary to wait for the
confirmation beep before speaking a
command.)
● Voice commands may not be recognized
if:
• Spoken too quickly.
• Spoken at a low or high volume.
Talk switch • The windows are open.
 Press the talk switch to start the voice • Passengers are talking while voice
command system. commands are spoken.
 To cancel voice recognition, press and • The air conditioning speed is set high.
hold the talk switch.
• The air conditioning vents are turned
towards the microphone.
● In the following conditions, the system
may not recognize the command prop-
erly and using voice commands may not
be possible:
• The command is incorrect or unclear.
Note that certain words, accents or
speech patterns may be difficult for the
system to recognize.
• There is excessive background noise,
such as wind noise.
124
VOICE COMMAND SYSTEM 4 Say the command displayed on the

screen.
OPERATION
The voice command system is operat-

ed by selecting a tab corresponding to
each function. The tabs are found on
the upper part of the screen.
1 Press the talk switch.
2 Select “OK”.  Registered POIs, registered names in the

4
contacts list etc., can be said in the place

of the “<>” next to the commands.
(P.130)
For example: Say “Find nearby dining”,
“Call John smith” etc.
 If a desired outcome is not shown, or if no
selections are available, perform one of
the following to return to the previous
screen:
• Say “Go back”.
 To train voice recognition and to display • Select “Go Back”.
the tutorial. (P.126)  To cancel voice recognition, select “Can-
 To prevent the screen from being dis- cel”, or press and hold the talk switch.
played again, select “Do Not Tell Me
Again”. INFORMATION
3 Say the tab selection command or se- ● If the system does not respond or the
confirmation screen does not disappear,
lect the desired tab. press the talk switch and try again.
● “Voice Recognition Prompts” can be
adjusted on the “Voice Settings” screen.
(P.61)
● Voice guidance can be canceled by set-
ting voice prompts to off. Use this setting
when it is desirable to say a command
immediately after pressing the talk
switch and hearing a beep.
 Commands related with each function are

displayed on the screen of the each func-
tion tab. Some commonly used com-
mands are displayed on the screen of the
function tab.
 Selecting “Help” or saying “Help”

prompts voice guidance to offer exam-
ples of commands and operation meth-
ods.
125
■DISPLAYING THE “Voice Settings” VOICE COMMAND EXAMPLE:

SCREENS LAUNCH Entune App Suite
APPLICATION (ENTUNE
PREMIUM AUDIO ONLY)
2 Say “Launch <application name>”.

 Entune App Suite application screen is
displayed.
 Selecting “Voice Settings” can be dis-

played the “Voice Settings” screen. VOICE COMMAND EXAMPLE:
(P.61) PERFORMING A DESTINATION
SEARCH BY ADDRESS
DISPLAYING THE TRAIN VOICE (ENGLISH ONLY) (ENTUNE
RECOGNITION AND TUTORIAL PREMIUM AUDIO ONLY)
SCREENS
2 Say “Enter an address”.
3 Say “<house number, street name,

city name, State>” continuously.
 A confirmation screen will be displayed
showing the recognition results. If multiple
matching items are found, a selection
screen will be displayed. Say “<num-
ber>” or select the number.
 Some areas cannot be recognized by the
No. Function voice recognition system.
Select to train voice recognition.  For information regarding the state/

province setting to perform a destination
Select to display the voice recogni- search by address: P.208
tion tutorial.
4 Say “Go directly”.
2 Select the desired item to be set.  After this, follow the voice guidance and
search for a destination route by voice
command operation.
126
INFORMATION VOICE COMMAND EXAMPLE:

● The voice command recognition is SEARCH FOR A SONG
designed to recognize the main body of
the official street name. 1 Press the talk switch.
For example: if the official street name is 2 Say “Play song <name>”.
“East Main Street”, the voice command
 A confirmation screen will be displayed
recognition will recognize “Main”. showing the recognition results. If multiple
● Say the desired number, cardinal/direc- matching items are found, a selection
tion etc. in the place of the “<>”. screen will be displayed. Say “<num-
For example: Say “West 555”. ber>” or select the number.
4
● Inputting the house number can be  The system starts playing music and the
skipped. song lists are displayed.

● Even if the state set using voice recogni-
tion is different from the set state in the INFORMATION
“Address” screen (which was set when a ● The Gracenote database is only com-
destination was set manually), the set patible with the USB or iPod mode.
state in the “Address” screen will not
● A USB memory or iPod must be con-
change. (P.209)
nected to enable track searching and
● The house number voice recognition playback. (P.97, 101)
conditions are outlined below:
● When a USB memory or iPod is con-
• Numerals: 10 digits or less nected, recognition data is created so
• Numerals and cardinal/direction or a tracks can be searched using voice
hyphen and numerals: A total of 9 commands.
digits or less (Do not say “and”.) ● Recognition data is updated under the
• Cardinal/direction or a hyphen and following conditions:
numerals: A total of 9 digits or less • When the USB memory or iPod data
(Do not say “and”.) has changed.
• Numerals are recognized as single • When the voice recognition language
digits only. is changed. (P.56)
• The cardinal/direction and hyphens ● While the recognition data is being cre-
are only recognized once. ated or being updated, a track search
• The following cardinal/directions can cannot be performed using a voice com-
be recognized: North, East, West and mand.
South.
127
VOICE COMMAND EXAMPLE: VOICE COMMAND EXAMPLE:

CALL NAME DIAL NUMBER
1 Press the talk switch. 1 Press the talk switch.
2 Say “Call <contacts> <phone 2 Say the phone number.

types>”.  In the same manner as it is displayed on
 A confirmation screen will be displayed the screen, “Dial <number>”, after saying
showing the recognition results. If multiple “Dial a number” say the phone number.
matching items are found, a selection  Say the phone number one digit at a time.
screen will be displayed. Say “<num- For example, if the phone number is
ber>” or select the number. 2345678:
Say “two three four five six seven
INFORMATION eight”
Do not say “twenty three forty five sixty
● In the same manner as it is displayed on seven eight”
the screen, “Call <contacts> <phone
types>”, after saying “Call a contact” Calling to the following phone numbers
say the name, or the name and type of • 3 digit numbers (911, 411, 611)
phone, of a contact. • 7 digit numbers (Local phone numbers)
For example: “Call a contact”, “John • 10 digit numbers (Area code + Local
Smith” or “Call a contact”, “Mary phone number)
Davis”, “Mobile” • 11 digit phone numbers (1 + Area code +
● There are 4 types of phones: Home, Local phone number)
Mobile, Work and Other.  As the system cannot recognize additional
● Short or abbreviated names in the con- numbers, say the complete number with-
tacts list may not be recognized. Change out stopping.
names in the contacts list to full names. 3 Say “Call” or press the switch on
● Sometimes a voice recognition result
the steering wheel.
confirmation screen will be displayed.
After confirming the result, say “Yes” or
“No”.  When the system recognizes multiple
phone numbers, a phone number candi-
● When the system recognizes multiple
date list will be displayed on the screen.
names from the contacts list, a name
candidate list will be displayed on the Pressing the switch on the steering
screen. If the desired name is not dis- wheel makes a call to the top entry on
played on the top of the screen, say or the list. If the desired phone number is
select the number of the name from the not displayed on the top of the screen,
candidate list (number 1 and number 2, say the number of the desired phone
etc.) to select a name from the candi- number from the candidate list to select
date list. a phone number from the candidate list.
● When a contact has multiple phone
numbers registered in the contacts list, a
candidate list will be displayed. If the
desired phone number is not displayed
on the top of the screen, say or select
the number of the desired phone num-
ber from the candidate list (number 1
and number 2, etc.) to select a phone
number from the candidate list.
128
2. CASUAL SPEECH RECOGNIZATION
Due to natural language speech recog- EXPRESSION EXAMPLES FOR

nition technology, this system enables EACH FUNCTION
recognition of a command when spo-
ken naturally. However, the system Command Expression examples
cannot recognize every variation of
Navigate to my house.
each command. In some situations, it “Go Home”*
Take me home.
is possible to omit the command for the
procedure and directly state the de- I need directions to an
“Enter an 
sired operation. Not all voice com- address.
Address”*
Give me a street.
mands are displayed in the function
4
menu. Search for a <Restau-
“Find Nearby  rants> around here.

<POI category>”* Find a <Restaurants>
INFORMATION
nearby.
● If the command cannot be recognized
completely, the command input screen Get me <Robert
will be displayed. (Search results will be “Call <name> Brown>.
shown based on the part of the com- <type>” Call <contacts>
mand that was recognized.) <phone types>.
“Dial <number>” Call <911>.
Play the artist <name>.

“Play Artist 
I want to hear the band
<name>”
<name>.
“Play Album 
Play album <name>.
<name>”
129
3. COMMAND LIST
Recognizable voice commands and their actions are shown below.

 Frequently used commands are listed in the following tables.
 For devices that are not installed in the vehicle, the related commands will not be dis-
played in the screen. Also, according to conditions, other commands may not be dis-
played in the screen.
 The functions available may vary according to the system installed.
 Voice recognition language can be changed. (P.56)
Basic
Command Action
Prompts voice guidance to offer examples of commands

“Help”
or operation methods
“Go Back” Returns to the previous screen
“Number one/two/three/four/five” Selects the number on the list screen
“Next Page” Displays the next page
“Previous Page” Displays the previous page
“Go to <tab>” Displays the command list of the selected tab
Entune App Suite application*1

When the voice recognition language is set to English.
Command Action
“Launch <apps>” Activates the Entune App Suite application
Navigation*1
Command Action
Displays a list of <POI category*2> near the current posi-

“Find Nearby <POI category>”
tion
“Enter an Address” Enables setting a destination by saying the address
“Go Home” Displays the route to home
“Cancel Route” Stops the route guidance
“Web search” Performs web search of POIs

*2: For example; “Gas stations”, “Restaurants”, etc.
130
Phone
Command Action
Places a call to the phone number of the latest outgoing

“Redial”
call
“Call Back” Places a call to the phone number of latest incoming call
“Show Recent Calls” Displays the call history screen
“Dial <phone number>” Places a call to the said phone number

4
Place a call to the said phone type of the contact from the
“Call <contacts> <phone types>”
phone book

Audio
Command Action
“Play Playlist <name>” Plays tracks from the selected playlist
“Play Artist <name>” Plays tracks from the selected artist
“Play Song <name>” Plays the selected track
“Play Album <name>” Plays tracks from the selected album
Info*
Command Action
“Show Forecast” Displays weather information
“Show Traffic” Displays traffic information
*: Available models and available country and areas (P.136, 137)
131
2. MOBILE ASSISTANT OPERATION
1. MOBILE ASSISTANT
The Mobile Assistant feature will • After some phone and music com-
mands, the Mobile Assistant feature will
activate Apple’s Siri® Eyes Free mode automatically end to complete the
via the steering wheel switches. To requested action.
operate the Mobile Assistant, a
compatible cellular phone must be  The volume of the Mobile Assistant can
be adjusted using the “PWR·VOL”
registered and connected to this knob or steering wheel volume control
system via Bluetooth®. (P.41) switches. The Mobile Assistant and
phone call volumes are synchronized.
1 Press and hold this switch until you
hear the beeps. INFORMATION
● The available features and functions
may vary based on the iOS version
installed on the connected device.
● Some Siri features are limited in Eyes
Free mode. If you attempt to use an
unavailable function, Siri will inform you
that the function is not available.
● If Siri is not enabled on the cellular
phone connected via Bluetooth®, an
error message will be displayed on the
screen.
2 The Mobile Assistant can be used only ● While a phone call is active, the Mobile
when the following screen is displayed. Assistant cannot be used.
● If using the navigation feature of the cel-
lular phone, ensure the active audio
source is Bluetooth® audio or iPod in
order to hear turn by turn direction
prompts.
 To cancel the Mobile Assistant: select

“Cancel”, press the on the steering
wheel, or press and hold the on the
steering wheel.
 To restart the Mobile Assistant for addi-
tional commands, press the on the
steering wheel.
• Mobile Assistant can only be restarted
after the system responds to a voice
command.
132
MICROPHONE
It is not necessary to speak directly into

the microphone when using the Mobile
Assistant. (Microphone location:
P.124)
INFORMATION
● Wait for the listening beeps before using
the Mobile Assistant. 4
● The Mobile Assistant may not recognize
commands in the following situations:

• Spoken too quickly.
• Spoken at a low or high volume.
• The roof or windows are open.
• Passengers are talking while the
Mobile Assistant is being used.
• The air conditioning speed is set high.
• The air conditioning vents are turned
toward the microphone.
133
134
5
1
INFORMATION
2
1 INFORMATION 3
1. RECEIVING WEATHER
INFORMATION ......................... 136 4
DISPLAYING WEATHER 
INFORMATION ................................. 136
5
2. RECEIVING TRAFFIC MAP
INFORMATION ......................... 137
DISPLAYING TRAFFIC MAP 6
INFORMATION ................................. 137
3. DATA SERVICES SETTINGS..... 138

7
SETTING DOWNLOAD METHODS .... 138
135
1. INFORMATION
1. RECEIVING WEATHER INFORMATION*
Entune Audio Plus 3 Check that the “Weather” screen is dis-

Weather radar information can be replayed.
ceived via the HD Radio.
Weather radar information can be re-
ceived via the HD Radio or by the En-
tune App Suite application on a
Bluetooth® phone.
DISPLAYING WEATHER No. Function

INFORMATION Select to display the weather of the
current location.
Select to display the weather of a
desired location in the recently
checked locations list.

desired location in the national cities
list.

desired location in the other local cit-
ies list.
Entune Premium Audio only:

2 Select “Weather”. Select to display Doppler weather
radar information over the map.
INFORMATION
● If “Weather” is set to the home screen,
the weather information of the current
location will be displayed.

136
1. INFORMATION
2. RECEIVING TRAFFIC MAP INFORMATION*
Traffic map information can be re- 3 Check that the traffic map screen is
ceived via the HD Radio. displayed.
DISPLAYING TRAFFIC MAP

INFORMATION
No. Function
Current position of your car

5
Traffic information line
INFORMATION
The line color means the following:
Red: Heavy congestion
Yellow: Moderate traffic
Green: Freely flowing traffic
2 Select “Traffic”.
*: Entune Audio Plus only (Available in the 48 states, D.C. and Alaska)
137
1. INFORMATION
3. DATA SERVICES SETTINGS*
SETTING DOWNLOAD 4 Select the desired item to be set.

METHODS
Data service information, which is

comprised of traffic information and
weather information, can be received
via the HD Radio and by the Entune
App Suite application on a Bluetooth®
phone. The receiving method can be  Select a checkbox on the right to set.
set to both or only via the HD Radio.
For details about the Entune App Suite No. Function
application: P.259
Select to receive data service infor-
1 Press the “APPS” button. mation via both the HD Radio and
the Entune App Suite application on
a Bluetooth® phone. When both
methods are available, the HD Ra-
dio will be selected.
Select to receive data only via the

HD Radio.
3 Select “HD Data”.
*: Entune Premium Audio only (Available in the 48 states, D.C. and Alaska)
138
6
1
PERIPHERAL MONITORING SYSTEM
2
REAR VIEW MONITOR  3

1
SYSTEM
1. REAR VIEW MONITOR  4

SYSTEM .................................... 140
DRIVING PRECAUTIONS ................... 140
SCREEN DESCRIPTION .................... 141 5
2. REAR VIEW MONITOR 

SYSTEM PRECAUTIONS......... 142 6
AREA DISPLAYED ON SCREEN........ 142
THE CAMERA ..................................... 142
7
DIFFERENCES BETWEEN 
THE SCREEN AND THE ACTUAL 
ROAD ................................................ 143
8
WHEN APPROACHING 
THREE-DIMENSIONAL OBJECTS... 145
3. THINGS YOU SHOULD  9

KNOW ....................................... 147
IF YOU NOTICE ANY SYMPTOMS .... 147
139
1. REAR VIEW MONITOR SYSTEM
The rear view monitor system assists CAUTION

the driver by displaying an image of the
view behind the vehicle with fixed ● Never depend on the rear view monitor
guide lines on the screen while backing system entirely when backing up. The
up, for example while parking. image and the position of the guide lines
displayed on the screen may differ from
the actual state.
INFORMATION Use caution, just as you would when
● The screen illustrations used in this text backing up any vehicle.
are intended as examples, and may dif- ● Be sure to back up slowly, depressing
fer from the image that is actually dis- the brake pedal to control vehicle speed.
played on the screen. ● The instructions given are only guide-
lines. When and how much to turn the
steering wheel will vary according to
traffic conditions, road surface condi-
DRIVING PRECAUTIONS tions, vehicle condition, etc. when park-
ing. It is necessary to be fully aware of
The rear view monitor system is a sup- this before using the rear view monitor
plemental device intended to assist the system.
driver when backing up. When backing ● When parking, be sure to check that the
parking space will accommodate your
up, be sure to visually check all around vehicle before maneuvering into it.
the vehicle both directly and using the ● Do not use the rear view monitor system
mirrors before proceeding. If you do in the following cases:
not, you may hit another vehicle, and • On icy or slick road surfaces, or in
could possibly cause an accident. snow
• When using tire chains or emergency
Pay attention to the following precau- tires
tions when using the rear view monitor • When the tail gate is not closed com-
system. pletely
• On roads that are not flat or straight,
such as curves or slopes.
● In low temperatures, the screen may
darken or the image may become faint.
The image could distort when the vehi-
cle is moving, or you may become
unable to see the image on the screen.
Be sure to visually check all around the
vehicle both directly and using the mir-
rors before proceeding.
● If the tire sizes are changed, the position
of the fixed guide lines displayed on the
screen may change.
● The camera uses a special lens. The
distances between objects and pedestri-
ans that appear in the image displayed
on the screen will differ from the actual
distances.(P.143)
140
SCREEN DESCRIPTION
The rear view monitor system screen will be displayed if the shift lever is shifted to
the “R” position while the engine switch is in “ON” position.
No. Display Function 6

Displays a guide path when the vehicle is being backed

straight up.
Vehicle width guide lines
 The displayed width is wider than the actual vehicle
width.
This line indicates the estimated vehicle center on the

Vehicle center guide line
ground.
Shows distance behind the vehicle.

Distance guide line  Displays a point approximately 1.5 ft. (0.5 m) (red) from
the edge of the bumper.
Shows distance behind the vehicle.

Distance guide line  Displays a point approximately 3 ft. (1 m) (blue) from
the edge of the bumper.
CANCELING REAR VIEW MONITOR SYSTEM
The rear view monitor system is canceled when the shift lever is shifted into any
position other than the “R” position.
141
2. REAR VIEW MONITOR SYSTEM PRECAUTIONS
AREA DISPLAYED ON THE CAMERA

SCREEN
The camera for the rear view monitor
The rear view monitor system displays system is located as shown in the illus-
an image of the view from the bumper tration.
of the rear area of the vehicle.
Displayed area
Screen USING THE CAMERA
If dirt or foreign matter (such as water

droplets, snow, mud etc.) is adhering
to the camera, it cannot transmit a
clear image. In this case, flush it with a
large quantity of water and wipe the
Corners of bumper camera lens clean with a soft and wet
cloth.
 The image adjustment procedure for the
rear view monitor system screen is the
same as the procedure for adjusting the
multimedia screen. (P.39)
INFORMATION
● The area displayed on the screen may
vary according to vehicle orientation
conditions.
● Objects which are close to either corner
of the bumper or under the bumper can-
not be displayed.
● The camera uses a special lens. The
distance of the image that appears on
the screen differs from the actual dis-
tance.
● Items which are located higher than the
camera may not be displayed on the
monitor.
142
NOTICE DIFFERENCES BETWEEN

THE SCREEN AND THE
● The rear view monitor system may not
operate properly in the following cases.
ACTUAL ROAD
• If the back of the vehicle is hit, the  The distance guide lines and the vehicle
position and mounting angle of the width guide lines may not actually be par-
camera may change. allel with the dividing lines of the parking
• As the camera has a water proof con- space, even when they appear to be so.
struction, do not detach, disassemble Be sure to check visually.
or modify it. This may cause incorrect
operation.  The distances between the vehicle width
• When cleaning the camera lens, flush guide lines and the left and right dividing
the camera with a large quantity of lines of the parking space may not be
water and wipe it with a soft and wet equal, even when they appear to be so.
cloth. Strongly rubbing the camera lens Be sure to check visually.
may cause the camera lens to be  The distance guide lines give a distance
scratched and unable to transmit a guide for flat road surfaces. In any of the
clear image. following situations, there is a margin of
• Do not allow organic solvent, car wax, error between the fixed guide lines on the 6
window cleaner or a glass coating to screen and the actual distance/course on
adhere to the camera. If this happens, the road.

wipe it off as soon as possible.
• If the temperature changes rapidly,
such as when hot water is poured on
the vehicle in cold weather, the system
may not operate normally.
• When washing the vehicle, do not
apply intensive bursts of water to the
camera or camera area. Doing so may
result in the camera malfunctioning.
● Do not expose the camera to strong
impact as this could cause a malfunc-
tion. If this happens, have the vehicle
inspected by your Toyota dealer as soon
as possible.
143
WHEN THE GROUND BEHIND WHEN THE GROUND BEHIND

THE VEHICLE SLOPES UP THE VEHICLE SLOPES DOWN
SHARPLY SHARPLY
The distance guide lines will appear to The distance guide lines will appear to
be closer to the vehicle than the actual be farther from the vehicle than the ac-
distance. Because of this, objects will tual distance. Because of this, objects
appear to be farther away than they ac- will appear to be closer than they actu-
tually are. In the same way, there will ally are. In the same way, there will be
be a margin of error between the guide a margin of error between the guide
lines and the actual distance/course on lines and the actual distance/course on
the road. the road.
144
WHEN ANY PART OF THE WHEN APPROACHING

VEHICLE SAGS THREE-DIMENSIONAL
When any part of the vehicle sags due
OBJECTS
to the number of passengers or the dis-
tribution of the load, there is a margin The distance guide lines are displayed
of error between the fixed guide lines according to flat surfaced objects
on the screen and the actual distance/ (such as the road). It is not possible to
course on the road. determine the position of three-dimen-
sional objects (such as vehicles) using
the vehicle width guide lines and dis-
tance guide lines. When approaching a
three-dimensional object that extends
outward (such as the flatbed of a
truck), be careful of the following.

A margin of error
145
VEHICLE WIDTH GUIDE LINES DISTANCE GUIDE LINES
Visually check the surroundings and Visually check the surroundings and
the area behind the vehicle. In the case the area behind the vehicle. On the
shown below, the truck appears to be screen, it appears that a truck is park-
outside of the vehicle width guide lines ing at point B. However, in reality if you
and the vehicle does not look as if it back up to point A, you will hit the truck.
hits the truck. However, the rear body On the screen, it appears that A is clos-
of the truck may actually cross over the est and C is farthest away. However, in
vehicle width guide lines. In reality if reality, the distance to A and C is the
you back up as guided by the vehicle same, and B is farther than A and C.
width guide lines, the vehicle may hit
the truck. Positions of A, B and C
AB
B
A
 Vehicle width guide lines
146
3. THINGS YOU SHOULD KNOW
IF YOU NOTICE ANY SYMPTOMS

If you notice any of the following symptoms, refer to the likely cause and the so-
lution, and re-check.
If the symptom is not resolved by the solution, have the vehicle inspected by
your Toyota dealer.
Symptom Likely cause Solution
The image is difficult to see  The vehicle is in a dark Back up while visually check-
area ing the vehicle’s surround-
 The temperature around ings. (Use the monitor again
the lens is either high or low
once conditions have been
 The outside temperature is
low improved.)
 There are water droplets on The procedure for adjusting
the camera the picture quality of the rear
 It is raining or humid view monitor system is the
 Foreign matter (mud etc.) is same as the procedure for 6
adhering to the camera
adjusting the screen. (P.39)
 Sunlight or headlights are

shining directly into the
camera
 The vehicle is under fluo-
rescent lights, sodium
lights, mercury lights etc.
The image is blurry Dirt or foreign matter (such as Flush the camera with a large
water droplets, snow, mud quantity of water and wipe the
etc.) is adhering to the cam- camera lens clean with a soft
era. and wet cloth.
The image is out of alignment The camera or surrounding Have the vehicle inspected by
area has received a strong your Toyota dealer.
impact.
The fixed guide lines are very The camera position is out of Have the vehicle inspected by
far out of alignment alignment. your Toyota dealer.
 The vehicle is tilted (there is If this happens due to these

a heavy load on the vehicle, causes, it does not indicate a
tire pressure is low due to a malfunction.
tire puncture, etc.)
 The vehicle is used on an Back up while visually check-
incline. ing the vehicle’s surround-
ings.
147
148
7
1
PHONE
2
6. Bluetooth® PHONE MESSAGE

PHONE OPERATION  FUNCTION ................................ 164 3
1 (HANDS-FREE SYSTEM  MESSAGE INBOX SCREEN ............... 164
FOR CELLULAR PHONES)
DISPLAYING THE MESSAGE INBOX 4
SCREEN IN A DIFFERENT WAY ..... 165
1. QUICK REFERENCE................... 150 RECEIVING A MESSAGE ................... 165
CHECKING MESSAGES..................... 166 5
2. SOME BASICS ............................ 151
REPLYING TO A MESSAGE 
REGISTERING/CONNECTING 
(QUICK REPLY) ................................ 167
A Bluetooth® PHONE........................ 151
CALLING THE MESSAGE SENDER... 168 6
USING THE PHONE SWITCH/
MICROPHONE ................................. 152
VOICE COMMAND SYSTEM.............. 152 2 SETUP 7
ABOUT THE CONTACTS IN THE
CONTACT LIST ................................ 153 1. PHONE/MESSAGE 
WHEN SELLING OR DISPOSING  SETTINGS.................................. 169 8
OF THE VEHICLE............................. 153
PHONE/MESSAGE SETTINGS 
SCREEN ........................................... 169
3. CALLING ON THE Bluetooth®
PHONE........................................154 “Sound Settings” SCREEN .................. 170 9
BY FAVORITES LIST .......................... 155 “Contact/Call History Settings” 

SCREEN ........................................... 171
BY CALL HISTORY ............................. 155
“Messaging Settings” SCREEN ........... 179
BY CONTACTS LIST .......................... 156
“Phone Display Settings” SCREEN ..... 180
BY DIAL PAD ...................................... 158
BY OFF HOOK SWITCH ..................... 158
BY “Home” SCREEN ........................... 159 3 WHAT TO DO IF...
4. RECEIVING ON THE Bluetooth® 1. TROUBLESHOOTING ................ 181

PHONE....................................... 160
INCOMING CALLS.............................. 160
5. TALKING ON THE Bluetooth®

PHONE....................................... 161
INCOMING CALL WAITING ................ 163
149
1. PHONE OPERATION (HANDS-FREE SYSTEM FOR CELLULAR PHONES)
1. QUICK REFERENCE
The phone top screen can be used to make a phone call. The phone screen can
be reached by following methods:
Press the “APPS” button and select “Phone”.
Press the switch on the steering wheel.
Press the button on the control panel.
Several functions are available to operate on each screen that is displayed by se-
lecting the 4 tabs.
Function Page
Registering/connecting Bluetooth® phone 41
Calling on the Bluetooth® phone 154

Phone operation
Receiving on the Bluetooth® phone 160
®
Talking on the Bluetooth phone 161
®
Message function Using the Bluetooth phone message function 164
Phone settings 169

Setting up a phone
®
Bluetooth settings 49
150
2. SOME BASICS
The hands-free system enables calls INFORMATION

to be made and received without hav-
● If your cellular phone does not support
ing to take your hands off the steering Bluetooth®, this system cannot function.
wheel. ● In the following conditions, the system
This system supports Bluetooth®. may not function:
Bluetooth® is a wireless data system • The cellular phone is turned off.
that enables cellular phones to be used • The current position is outside the
without being connected by a cable or communication area.
placed in a cradle. • The cellular phone is not connected.
• The cellular phone has a low battery.
The operating procedure of the phone
is explained here. ● When using Bluetooth® audio and
hands-free at the same time, the follow-
ing problems may occur:
CAUTION • The Bluetooth® connection may be
cut.
● While driving, do not use a cellular
phone or connect the Bluetooth® phone. • Noise may be heard on the Bluetooth®
audio playback.
● Your audio unit is fitted with Bluetooth®
antennas. People with implantable car-
diac pacemakers, cardiac resynchroni- 7
zation therapy-pacemakers or REGISTERING/CONNECTING
implantable cardioverter defibrillators A Bluetooth® PHONE
PHONE
should maintain a reasonable distance
between themselves and the Bluetooth®
antennas. The radio waves may affect To use the hands-free system for cellu-
the operation of such devices. lar phones, it is necessary to register a
● Before using Bluetooth® devices, users cellular phone with the system.
of any electrical medical device other (P.41)
than implantable cardiac pacemakers,
cardiac resynchronization therapy-pace-
makers or implantable cardioverter Bluetooth® PHONE CONDITION
defibrillators should consult the manu- DISPLAY
facturer of the device for information
about its operation under the influence The condition of the Bluetooth® phone
of radio waves. Radio waves could have appears on the upper right side of the
unexpected effects on the operation of
such medical devices. screen. (P.18)
NOTICE
● Do not leave your cellular phone in the
vehicle. The temperature inside may rise
to a level that could damage the phone.
151
USING THE PHONE SWITCH/ VOICE COMMAND SYSTEM

MICROPHONE
Press this switch to operate the voice
Steering switch command system.
By pressing the phone switch, a call
can be received or ended without tak-
ing your hands off the steering wheel.
 The voice command system and its list

of commands can be operated.
(P.124)
Volume control switch

 Press the switch to increase or decrease
the volume during a phone call.
Off hook switch
On hook switch
Microphone
The microphone is used when talking

on the phone.
152
INFORMATION ABOUT THE CONTACTS IN

● The other party’s voice will be heard THE CONTACT LIST
from the front speakers. The audio sys-
tem will be muted during phone calls or  The following data is stored for every reg-
when hands-free voice commands are istered phone. When another phone is
used. connected, the following registered data of
● Talk alternately with the other party on the previously connected phone cannot be
the phone. If both parties speak at the read:
same time, the other party may not hear • Contact data
what has been said. (This is not a mal- • Call history data
function.) • Favorites data
● Keep call volume down. Otherwise, the • Image data
other party’s voice may be audible out- • All phone settings
side the vehicle and voice echo may • Message settings
increase. When talking on the phone,
speak clearly towards the microphone. INFORMATION
● The other party may not hear you clearly ● When a phone’s registration is deleted,
when: the above-mentioned data is also
• Driving on an unpaved road. (Making deleted.
excessive traffic noise.)
• Driving at high speeds. 7
• The windows are open. WHEN SELLING OR
• The air conditioning vents are pointed DISPOSING OF THE VEHICLE
PHONE
towards the microphone.
• The sound of the air conditioning fan is
loud. A lot of personal data is registered
• There is a negative effect on sound when the hands-free system is used.
quality due to the phone and/or net- When selling or disposing of the vehi-
work being used. cle, initialize the data. (P.60)
 The following data in the system can be
initialized:
• Contact data
• Call history data
• Favorites data
• Image data
• All phone settings
• Message settings
INFORMATION
● Once initialized, the data and settings
will be erased. Pay careful attention
when initializing the data.
153
3. CALLING ON THE Bluetooth® PHONE
After a Bluetooth® phone has been How to make a call list Page
registered, a call can be made using By favorites list 155
the hands-free system. There are sev-
eral methods by which a call can be By call history 155
made, as described below. By contacts list 156
1 Press the “APPS” button. By dial pad 158
By e-mail/SMS/MMS 168
By POI call* 200
By off hook switch 158
By Entune App Suite* 266
By voice command system 128
By “Home” screen 159

3 Select the desired tab to call from.
 The phone top screen can be displayed by

pressing the switch on the steering
wheel.
154
BY FAVORITES LIST BY CALL HISTORY
Calls can be made using registered Up to 30 of the latest call history items
contacts which can be selected from a (missed, incoming and outgoing) can
contact list. (P.176) be selected from the “Call History” tab.
1 Display the phone top screen. 1 Display the phone top screen.
(P.154) (P.154)
2 Select the “Favorites” tab and select 2 Select the “Call History” tab and se-
the desired contact.
lect or the desired contact.
7
3 Select the desired number.
 The icons of call type are displayed.
4 Check that the “Call” screen is dis-
PHONE
: Missed call
played.
: Incoming call
: Outgoing call
When is selected
played.
When the desired contact is selected

played.
155
INFORMATION BY CONTACTS LIST

● When making a call to the same number
continuously, only the most recent call is Calls can be made by using contact
listed in call history. data which is transferred from a regis-
● When a phone number registered in the tered cellular phone. (P.157)
contact list is received, the name is dis-
played. Up to 2500 contacts (maximum of 4
● Number-withheld calls are also memo- phone numbers and e-mail addresses
rized in the system. per contact) can be registered in the
● International phone calls may not be contact list.
made depending on the type of cellular
phone you have. 1 Display the phone top screen.
● The list should group together consecu- (P.154)
tive entries with the same phone number
and same call type. For example, two 2 Select the “Contacts” tab and select
calls from Kay Rowles’s mobile would the desired contact.
be displayed as follows: Kay Rowles (2)
● By pressing the switch on the steer-
ing wheel, a call to the latest history item
can be made.

played.
156
WHEN THE CONTACT IS ■FOR PBAP INCOMPATIBLE BUT

EMPTY OPP COMPATIBLE Bluetooth®
PHONES
■FOR PBAP COMPATIBLE
® 1 Select the desired item.
Bluetooth PHONES
When “Automatic Contact/History
Transfer” is set to off (P.171)
1 Display the phone top screen.
(P.154)
 The following screen will not display when
transferring from a hands-free mode.
No. Function
Select to transfer the contacts from

the connected cellular phone.
Select to add a new contact manual-

ly.
7
Select to cancel transferring.
PHONE
When “Transfer” is selected
No. Function
Select to transfer new contacts from

2 Follow the steps in “FOR PBAP IN-
a cellular phone, select “Always” COMPATIBLE BUT OPP COMPATI-
and then enable “Automatic Con- BLE Bluetooth® PHONES” from
tact/History Transfer”. “STEP 2”. (P.172)
Select to transfer all the contacts When “Add” is selected
from a connected cellular phone
only once. 2 Follow the steps in “REGISTERING A
NEW CONTACT TO THE CONTACT
Select to cancel transferring. LIST” from “STEP 2”. (P.173)
157
INFORMATION BY OFF HOOK SWITCH

● Manual transfer operation cannot be
performed while driving. Calls can be made using the latest call
● If your cellular phone is neither PBAP history item.
nor OPP compatible, the contacts can-
not be transferred. 1 Press the switch on the steering
● Depending on the type of Bluetooth® wheel to display the phone top screen.
phone:
• It may be necessary to perform addi- 2 Press the switch on the steering
tional steps on the phone when trans- wheel to display the “Call History”
ferring contact data. screen.
• The registered image in the contact list
may not transfer depending on the 3 Press the switch on the steering
type of Bluetooth® phone connected. wheel to call the latest history item.
BY DIAL PAD played.
This operation cannot be performed

while driving.

(P.154)
2 Select the “Dial Pad” tab and enter the
phone number.
3 Select or press the switch on

the steering wheel.
played.
INFORMATION
● Depending on the type of Bluetooth®
phone being connected, it may be nec-
essary to perform additional steps on
the phone.
158
BY “Home” SCREEN REGISTERING A NEW

CONTACT ON THE “Home”
When the phone screen is on the SCREEN
“Home” screen.
1 Select and hold one of the contact but-
1 Press the “HOME” button.
ton on the screen.
2 Enter the name and phone number.
INFORMATION
● If there is no contact in the contacts list,
the contacts cannot be registered at the
home screen.
● The contact cannot be registered at the
home screen while driving.
2 Select the desired contact.

played.
INFORMATION 7
● If “No phone connected.” is displayed on
the screen, a registered phone is not
PHONE
connected to the system. To connect a
registered phone, select the “Select
Phone”.
159
4. RECEIVING ON THE Bluetooth® PHONE
INCOMING CALLS
When a call is received, this screen is

displayed with a sound.

the steering wheel to talk on the phone.
To refuse to receive the call: Select
or press the switch on the steer-

ing wheel.
To adjust the volume of a received call:
Turn the “PWR·VOL” knob, or use the vol-
ume control switch on the steering wheel.
INFORMATION
● During international phone calls, the
other party’s name or number may not
be displayed correctly depending on the
type of cellular phone you have.
● The incoming call display mode can be
set. (P.180)
● The ringtone that has been set in the
“Sound Settings” screen sounds when
there is an incoming call. Depending on
the type of Bluetooth® phone, both the
multimedia system and Bluetooth®
phone may sound simultaneously when
there is an incoming call. (P.170)
160
5. TALKING ON THE Bluetooth® PHONE
While talking on the phone, this screen INFORMATION

is displayed. The operations outlined
● Changing from hands-free call to cellular
below can be performed on this phone call is not possible while driving.
screen. ● When cellular phone call is changed to
hands-free call, the hands-free screen
will be displayed and its functions can be
operated on the screen.
● Changing between cellular phone call
and hands-free call can be performed by
operating the cellular phone directly.
● Transferring methods and operations
will be different depending on the type of
cellular phone you have.
● For the operation of the cellular phone,
No. Function Page see the manual that comes with it.
Select to display the dial

161
pad to send tones.
SENDING TONES
Select to mute your voice

to the other party. ■BY DIAL PAD
7
Select to change handset This operation cannot be performed
modes between hands- 
while driving.
PHONE
free and cellular phone.
Select to adjust your voice 1 Select “0-9”.

volume that the other party 162
hears from their speaker.
Select to send tones. This

button only appears when
a number that contains a 162
(w) is dialed in hands-free
mode.
Select to hang up the


phone. 2 Enter the desired number.
Select “+” or “-” to adjust
the volume of the other par- 
ty’s voice.
Select to start talking with

163
the other party.
161
■BY SELECTING “Release Tones” TRANSMIT VOLUME SETTING

“Release Tones” appear when a con- 1 Select “Transmit Volume”.
tinuous tone signal(s) containing a (w)
is registered in the contact list. 2 Select the desired level for the transmit
volume.
This operation can be performed while
driving.
1 Select “Release Tones”.
INFORMATION
● A continuous tone signal is a character
string that consists of numbers and the
characters p or w. (e.g.
056133w0123p#1) 3 Select “OK”.
● When the “p” pause tone is used, the
tone data up until the next pause tone
will be automatically sent after 2 sec- INFORMATION
onds have elapsed. When the “w” pause ● The sound quality of the voice heard
tone is used, the tone data up until the from the other party’s speaker may be
next pause tone will be automatically negatively impacted.
sent after a user operation is performed. ● To reset the transmit volume, select
● Release tones can be used when auto- “Default”.
mated operation of a phone based ser- ● “Transmit Volume” is dimmed when
vice such as an answering machine or mute is on.
bank phone service is desired. A phone
number with continuous tone signals
can be registered in the contact list.
● Tone data after a “w” pause tone can be
operated on voice command during a
call.
162
INCOMING CALL WAITING
When a call is interrupted by a third

party while talking, this screen is dis-
played.

the steering wheel to start talking with
the other party.
To refuse to receive the call: Select

7
or press the switch on the steer-
ing wheel.
PHONE
 Each time is selected or the
switch on the steering wheel is pressed
during an interrupted call, the party who is
on hold will be switched.
INFORMATION
● This function may not be available
depending on the type of cellular phone.
163
6. Bluetooth® PHONE MESSAGE FUNCTION
Received messages can be forwarded MESSAGE INBOX SCREEN

from the connected Bluetooth® phone,
enabling checking and replying using
the multimedia system.
Depending on the type of Bluetooth®
phone connected, received messages
may not be transferred to the message
inbox.
If the phone does not support the mes-
sage function, this function cannot be
used. : Select to change to phone mode.
Function Page
Receiving a message 165
Checking messages 166
Replying to a message (quick re-

167
ply)
Calling the message sender 168
Message settings 179
2 Select “Messages”.
164
DISPLAYING THE MESSAGE RECEIVING A MESSAGE

INBOX SCREEN IN A
DIFFERENT WAY When an e-mail/SMS/MMS is re-
ceived, the incoming message screen
1 Display the phone top screen. pops up with sound and is ready to be
(P.154) operated on the screen.
2 Select .
No. Function
 The phone top screen can be displayed by
E-mail: 
pressing the switch on the steering
wheel. Select to check the message.
7
Select to not open the message.
PHONE
Select to call the message sender.
INFORMATION
● Depending on the cellular phone used
for receiving messages, or its registra-
tion status with the multimedia system,
some information may not be displayed.
● The pop up screen is separately avail-
able for incoming e-mail and SMS/MMS
messages under the following condi-
tions:
E-mail:
• “Incoming E-mail Display” is set to “Full
Screen”. (P.179)
• “E-mail Notification Popup” is set to on.
(P.179)
SMS/MMS:
• “Incoming SMS/MMS Display” is set to
“Full Screen”. (P.179)
• “SMS/MMS Notification Popup” is set
to on. (P.179)
165
CHECKING MESSAGES INFORMATION

● Reading a text message is not available
1 Display the message inbox screen. while driving.
(P.164) ● Depending on the type of Bluetooth®
phone being connected, it may be
2 Select the desired message from the
necessary to perform additional steps on
list. the phone.
3 Check that the message is displayed. ● Messages are displayed in the
appropriate connected Bluetooth®
phone’s registered mail address folder.
Select the tab of the desired folder to be
displayed.
● Only received messages on the
connected Bluetooth® phone can be
displayed.
● The text of the message is not displayed
while driving.
● Turn the “PWR·VOL” knob, or use the
No. Function volume control switch on the steering
wheel to adjust the message read out
E-mail: 
volume during message playback.
Select “Mark Unread” or “Mark
Read” to mark mail unread or read
on the message inbox screen.
This function is available when “Up-
date Message Read Status on
Phone” is set to on. (P.179)
Select to reply the message.

(P.167)
Select to display the previous or

next message.
Select to have messages read out.

To cancel this function, select
“Stop”.
When “Automatic Message Read-
out” is set to on, messages will be
automatically read out. (P.179)
Select to make a call to the sender.
166
REPLYING TO A MESSAGE ■EDITING QUICK REPLY MESSAG-

ES
(QUICK REPLY)
15 messages have already been while driving.
stored.
1 Select “Quick Message”.
1 Display the message inbox screen.
(P.164)
2 Select the desired message from the
list.
3 Select “Quick Message”.
2 Select corresponding to the de-

sired message to edit.
3 Select “OK” when editing is complet-
ed. 7
4 Select the desired message.
PHONE
INFORMATION
5 Select “Send”. ● To reset the edited quick reply
messages, select “Default”.
 While the message is being sent, a send-
ing message screen is displayed.  Entune Premium Audio
 To cancel sending the message, select ● “Quick Message 1” (“I am driving and
“Cancel”. will arrive in approximately [ETA]
minutes.”):
This message cannot be edited and will
automatically fill in [ETA] with the
navigation calculated estimated time of
arrival on the confirm message screen.
If there are waypoints set, [ETA] to the
next waypoint will be shown.
If there is no route currently set in the
navigation system, “Quick Message 1”
cannot be selected.
167
CALLING THE MESSAGE ■CALLING FROM A NUMBER WITH-

IN A MESSAGE
SENDER
Calls can be made to a number identi-
Calls can be made to an e-mail/SMS/ fied in a message’s text area.
MMS message sender’s phone num-
ber.
while driving.
This operation can be performed while
driving. 1 Display the message inbox screen.
(P.164)
■CALLING FROM E-MAIL/SMS/MMS 2 Select the desired message.
MESSAGE DISPLAY
3 Select the text area.
1 Display the message inbox screen.
(P.164)
2 Select the desired message.
3 Select .

 Identified phone numbers contained in the
message are displayed.
played.
 If there are 2 or more phone numbers,
select the desired number.
INFORMATION
● A series of numbers may be recognized
played. as a phone number. Additionally, some
phone numbers may not be recognized,
such as those for other countries.
■CALLING FROM THE INCOMING

MESSAGE SCREEN
P.165
168
2. SETUP
1. PHONE/MESSAGE SETTINGS
1 Press the “APPS” button. DISPLAYING THE PHONE/

MESSAGE SETTINGS SCREEN
IN A DIFFERENT WAY

(P.154)
2 Select “Settings”.
4 Select the item to be set.
PHONE/MESSAGE SETTINGS
SCREEN 7
PHONE
No. Information Page
Registering/connecting a
41
phone
Sound settings 170
Contact/call history set-

171
tings
Messaging settings 179
Phone display settings 180
169
2. SETUP
“Sound Settings” SCREEN No. Function
Select to set the desired ringtone.

The call and ringtone volume can be
adjusted. A ringtone can be selected. Select “-” or “+” to adjust the ring-
tone volume.
1 Display the “Phone/Message Settings”
screen. (P.169) Select “-” or “+” to adjust the mes-
sage readout volume.
2 Select “Sound Settings”.
Select to set the desired incoming
3 Select the desired item to be set. SMS/MMS tone.
Select “-” or “+” to adjust the in-

coming SMS/MMS tone volume.
Select to set the desired incoming e-

mail tone.
Select “-” or “+” to adjust the in-

coming e-mail tone volume.
Select “-” or “+” to adjust the de-

fault volume of the other party’s
voice.
INFORMATION
● Depending on the type of phone, certain
functions may not be available.
170
2. SETUP
“Contact/Call History No. Function Page

Settings” SCREEN For PBAP compatible Blue-
tooth® phones, select to
The contact can be transferred from a set automatic contact/his-
tory transfer on/off. When 
Bluetooth® phone to the system. The set to on, the phone’s con-
contact also can be added, edited and tact data and history are
deleted. automatically transferred.
The call history can be deleted and Select to update contacts
contact and favorites can be changed. 172
from the connected phone.
1 Display the “Phone/Message Settings” Select to sort contacts by

screen. (P.169) the first name or last name 
field.
2 Select “Contact/Call History Set-
tings”. Select to add contacts to
176
the favorites list.
Select to delete contacts
178
from the favorites list.
Select to set the trans- 7

ferred contact image dis- 
play on/off.
PHONE
Select to clear contacts
* 
from the call history.
Select to add new contacts

* 173
to the contact list.
Select to edit contacts in

* 174
the contact list.
Select to delete contacts

* 175
from the contact list.
Select to reset all setup


items.
*: For PBAP compatible Bluetooth®

phones, this function is available when
“Automatic Contact/History Transfer” is
set to off. (P.171)
171
2. SETUP
INFORMATION
■FOR PBAP INCOMPATIBLE BUT
● Depending on the type of phone, certain OPP COMPATIBLE Bluetooth®
functions may not be available. PHONES
● Contact data is managed independently
for every registered phone. When one This operation cannot be performed
phone is connected, another phone’s while driving.
registered data cannot be read.
1 Select “Update Contacts from
Phone”.
UPDATE CONTACTS FROM
2 Transfer the contact data to the system
PHONE
using a Bluetooth® phone.
Operation methods differ between  This operation may be unnecessary
PBAP compatible and PBAP incom- depending on the type of cellular phone.
 Depending on the type of cellular phone,
patible/OPP compatible Bluetooth® OBEX authentication may be required
phones. when transferring contact data. Enter
If your cellular phone is neither PBAP “1234” into the Bluetooth® phone.
nor OPP compatible, the contacts can-  To cancel this function, select “Cancel”.
not be transferred. 3 Check that a confirmation screen is
■FOR PBAP COMPATIBLE plete.
®
Bluetooth PHONES
1 Select “Update Contacts from
Phone”.
 Contacts are transferred automatically.
plete.
 This operation may be unnecessary
depending on the type of cellular phone.
 Depending on the type of cellular phone,
OBEX authentication may be required
when transferring contact data. Enter
“1234” into the Bluetooth® phone.
 If another Bluetooth® device is connected
when transferring contact data, depending
on the phone, the connected Bluetooth®
device may need to be disconnected.
 Depending on the type of Bluetooth®
phone being connected, it may be neces-
sary to perform additional steps on the
phone.
172
2. SETUP
■UPDATING THE CONTACTS IN A REGISTERING A NEW

DIFFERENT WAY (FROM THE “Call CONTACT TO THE CONTACT
History” SCREEN) LIST
For PBAP compatible Bluetooth® New contact data can be registered.

phones, this function is available when Up to 4 numbers per person can be
“Automatic Contact/History Transfer” registered. For PBAP compatible
is set to off. (P.171)
Bluetooth® phones, this function is
1 Display the phone top screen. available when “Automatic Contact/
(P.154) History Transfer” is set to off. (P.171)
2 Select the “Call History” tab and se- 1 Select “New Contact”.
lect a contact not yet registered in the
contact list.
2 Enter the name and select “OK”.
3 Select “Update Contact”. 3 Enter the phone number and select

“OK”.
4 Select the phone type for the phone
5 Select a phone type for the phone number.
7
number.
5 To add another number to this contact,
select “Yes”.
PHONE
173
2. SETUP
■REGISTERING A NEW CONTACT IN EDITING THE CONTACT DATA

A DIFFERENT WAY (FROM THE
“Call History” SCREEN) For PBAP compatible Bluetooth®
1 Display the phone top screen. phones, this function is available when
(P.154) “Automatic Contact/History Transfer”
is set to off. (P.171)
2 Select the “Call History” tab and se-
lect a contact not yet registered in the 1 Select “Edit Contacts”.
contact list.
3 Select “Add to Contacts”.
3 Select corresponding to the de-
sired name or number.
LIST” from “STEP 2”. (P.173)
For editing the name

For editing the number
174
2. SETUP
■EDITING THE CONTACT IN A DIF- DELETING THE CONTACT

FERENT WAY (FROM THE “Contact DATA
Details” SCREEN)
1 Display the phone top screen. For PBAP compatible Bluetooth®
(P.154) phones, this function is available when
“Automatic Contact/History Transfer”
2 Select the “Contacts”, “Call history” is set to off. (P.171)
tab or the “Favorites” tab and select
the desired contact. 1 Select “Delete Contacts”.
3 Select “Edit Contact”. 2 Select the desired contact and select
“Delete”.
screen appears.
INFORMATION
● Multiple data can be selected and
deleted at the same time.
“E-mail Addresses”: Select to display all 7

registered e-mail addresses for the con-
tact.
PHONE
4 Follow the steps in “EDITING THE
CONTACT DATA” from “STEP 4”.
(P.174)
175
2. SETUP
■DELETING THE CONTACT IN A DIF- FAVORITES LIST SETTING

FERENT WAY (FROM THE “Contact
Details” SCREEN) Up to 15 contacts (maximum of 4 num-
bers per contact) can be registered in
the favorites list.
(P.154)
2 Select the “Contacts”, “Call history” ■REGISTERING THE CONTACTS IN
tab or the “Favorites” tab and select THE FAVORITES LIST
the desired contact.
1 Select “Add Favorite”.
3 Select “Delete Contact”.
2 Select the desired contact to add to the
4 Select “Yes” when the confirmation favorites list.
screen appears.
INFORMATION
● When a Bluetooth® phone is deleted,

the contact data will be deleted at the
same time.
 Dimmed contacts are already stored as a

favorite.
plete.
176
2. SETUP
When 15 contacts have already been Registering contacts in the favorites list
registered to the favorites list in a different way (from the “Contacts”
screen)
1 When 15 contacts have already been
registered to the favorites list, a regis- 1 Display the phone top screen.
tered contact needs to be replaced. (P.154)
Select “Yes” when the confirmation
screen appears to replace a contact.
2 Select the “Contacts” tab.
2 Select the contact to be replaced. 3 Select  at the beginning of the de-

sired contact list name to be registered
in the favorites list.

 When selected,  is changed to , and 7
plete. the contact is registered in the favorites
list.
PHONE
Registering contacts in the favorites list
in a different way (from the “Contact De-
tails” screen)
(P.154)
2 Select the “Contacts” tab or the “Call
History” tab and select the desired
contact.
3 Select “Add Favorite”.

plete.
177
2. SETUP
■DELETING THE CONTACTS IN THE Deleting contacts in the favorites list in a

FAVORITES LIST different way (from the “Contacts”
screen)
1 Select “Remove Favorite”.
2 Select the desired contacts and select (P.154)
“Remove”.
2 Select the “Contacts” tab.
3 Select  at the beginning of the con-

tact list name to be deleted from the fa-
vorites list.

screen appears.
plete.  When selected,  is changed to , and
the data is deleted from the list.
Deleting contacts in the favorites list in a
different way (from the “Contact Details”
screen)
(P.154)
2 Select the “Contacts”, “Call history”
tab or the “Favorites” tab and select
the desired contact to delete.
3 Select “Remove Favorite”.

screen appears.
plete.
178
2. SETUP
“Messaging Settings” No. Function

SCREEN Select to set automatic message
transfer on/off.
Select to set automatic message
screen. (P.169)
readout on/off.
2 Select “Messaging Settings”.
Select to set the SMS/MMS notifica-
3 Select the desired item to be set. tion popup on/off.
Select to set the e-mail notification

popup on/off.
Select to set adding the vehicle signa-

ture to outgoing messages on/off.
Select to set updating message read

status on phone on/off.
Select to change the incoming SMS/

MMS display.
“Full Screen”: When an SMS/MMS
message is received, the incoming 7
SMS/MMS display screen is dis-
played and can be operated on the
PHONE
screen.
“Drop-down”: When an SMS/MMS
message is received, a message is
displayed on the upper side of the
screen.
Select to change the incoming e-mail

display.
“Full Screen”: When an e-mail is re-
ceived, the incoming e-mail display
screen is the displayed and can be
operated on the screen.
“Drop-down”: When an e-mail is re-
ceived, a message is displayed on the
upper side of the screen.
Select to set display of messaging ac-

count names on the inbox tab on/off.
When set to on, messaging account
names used on the cellular phone will
be displayed.
179
2. SETUP
INFORMATION “Phone Display Settings”

● Depending on the phone, these func- SCREEN
tions may not be available.
screen. (P.169)
DISPLAYING THE “Messaging
Settings” SCREEN IN A 2 Select “Phone Display Settings”.
DIFFERENT WAY 3 Select the desired item to be set.
(P.154)
2 Select .
3 Select “Settings”.
No. Function
Select to change the incoming call

display.
“Full Screen”: When a call is re-
ceived, the hands-free screen is dis-
played and can be operated on the
screen.
“Drop-down”: A message is dis-
played on the upper side of the
screen.
Select to set display of the contact/

history transfer completion message
on/off.
INFORMATION
● Depending on the phone, these func-
tions may not be available.
180
3. WHAT TO DO IF...
1. TROUBLESHOOTING
If there is a problem with the hands-free system or a Bluetooth® device, first check
the table below.
When using the hands-free system with a Bluetooth® device
Page
Symptom Likely cause Solution Cellular This
phone system
For a list of specific

devices which
operation has been
The connected de- confirmed on this
vice may not be a system, check with
compatible your Toyota dealer or  
The hands-free sys- Bluetooth® cellular the following
phone. website: 
tem or Bluetooth®
http://
device does not
www.toyota.com/
work.
entune/
Use a cellular phone 7

The Bluetooth® ver-
sion of the connected ®
with Bluetooth ver-

PHONE
cellular phone may sion 2.0 or higher 43
be older than the (recommended: Ver.
specified version. 3.0 +EDR or higher).
181
3. WHAT TO DO IF...
When registering/connecting a cellular phone
Page
phone system
An incorrect pass- Enter the correct

code was entered on passcode on the cel-  
the cellular phone. lular phone.
Complete the regis-

The registration op-
tration operation on
eration has not been
the cellular phone  
completed on the
(approve registration
cellular phone side.
A cellular phone can- on the phone).
not be registered.
Delete the existing
registration informa-
Old registration infor- tion from both this
mation remains on system and the cellu-
 51
either this system or lar phone, then regis-
the cellular phone. ter the cellular phone
you wish to connect
to this system.
Manually connect the

Another Bluetooth® cellular phone you
device is already  52
wish to use to this
connected. system.
Enable the
Bluetooth® function
Bluetooth® function  
A Bluetooth® con- is not enabled on the
on the cellular
nection cannot be cellular phone.
phone.
made.
Set automatic
Automatic Bluetooth® connec-
Bluetooth® connection on this system to  55
tion on this system is on when the engine
set to off. switch is in the “ACC”
or “ON” position.
182
3. WHAT TO DO IF...
Page
phone system
Enable the
Bluetooth® function
Bluetooth® function  
is not enabled on the
on the cellular
cellular phone.
phone.
“Unable to dial. Delete the existing

Please check your registration informa-
phone.” Old registration infor- tion from both this
mation remains on system and the cellu-
 51
either this system or lar phone, then regis-
the cellular phone. ter the cellular phone
you wish to connect
to this system.
When making/receiving a call
Page
7
phone system
PHONE
Move to where “No
A call cannot be Your vehicle is in a Service” no longer
 
made/received. “No Service” area. appears on the dis-
play.
183
3. WHAT TO DO IF...
When using the contacts
Page
phone system
For a list of specific

devices which
operation has been
The profile version of
confirmed on this
the connected cellu-
system, check with
lar phone may not be
your Toyota dealer or  
compatible with
the following
transferring contact
website: 
data.
http://
www.toyota.com/
entune/
Contact data cannot Automatic contact
be transferred manu- Set automatic con-
transfer function on
ally/automatically. tact transfer function  171
this system is set to
on this system to on.
off.
Enter the passcode

Passcode has not
on the cellular phone
been entered on the  
if requested (default
cellular phone.
passcode: 1234).
Complete transfer
Transfer operation operation on the cel-
on the cellular phone lular phone (approve  
has not completed. transfer operation on
the phone).
Automatic contact
Set automatic con-
Contact data cannot transfer function on
tact transfer function  171
be edited. this system is set to
on this system to off.
on.
184
3. WHAT TO DO IF...
When using the Bluetooth® message function
Page
phone system
Enable message
Message transfer is transfer on the cellu-
not enabled on the lar phone (approve  
Messages cannot be cellular phone. message transfer on
viewed. the phone).
Automatic transfer Set automatic trans-

function on this sys- fer function on this  179
tem is set to off. system to on.
Notification of SMS/ Set notification of

MMS/E-mail recep- SMS/MMS/E-mail
 179
tion on this system is reception on this sys-
New message notifi- set to off. tem to on.
cations are not dis-
played. Automatic message
Enable automatic 7
transfer function is
transfer function on  
not enabled on the
the cellular phone.
cellular phone.
PHONE
In other situations
Page
phone system
The Bluetooth® con-

nection status is dis- Connection confir- To turn off the dis-
played at the top of mation display on play, set connection
the screen each time  54
this system is set to confirmation display
the engine switch is on. on this system to off.
in the “ACC” or “ON”
position.
185
3. WHAT TO DO IF...
Page
phone system
The cellular phone is Bring the cellular

not close enough to phone closer to this  
this system. system.
Turn the cellular

phone off, remove
and reinstall the bat-
 
tery pack, and then
restart the cellular
phone.
Even though all con- Enable the cellular

ceivable measures phone’s Bluetooth®  
have been taken, the connection.
symptom status does The cellular phone is
not change. the most likely cause Stop the cellular
of the symptom. phone’s security soft-
 
ware and close all
applications.
Before using an ap-

plication installed on
the cellular phone,
carefully check its  
source and how its
operation might af-
fect this system.
: For details, refer to the owner’s manual that came with the cellular phone.
186
3. WHAT TO DO IF...
PHONE
187
8
NAVIGATION SYSTEM*
1 BASIC OPERATION 2 DESTINATION SEARCH
1. QUICK REFERENCE ................... 190 1. DESTINATION SEARCH 

MAP SCREEN ..................................... 190 SCREEN .................................... 205
NAVIGATION OPTIONS SCREEN...... 192
2. SEARCH OPERATION................ 207
2. MAP SCREEN OPERATION ....... 193 SELECTING SEARCH AREA .............. 208
CURRENT POSITION DISPLAY ......... 193 SETTING HOME AS DESTINATION ... 208
MAP SCALE ........................................ 193 SETTING PRESET DESTINATIONS 
AS DESTINATION............................. 208
ORIENTATION OF THE MAP ............. 194
SEARCHING BY ADDRESS................ 209
SWITCHING THE MAP MODE............ 194
SEARCHING BY POINT OF 
SCREEN SCROLL OPERATION ........ 196
INTEREST ......................................... 210
ADJUSTING LOCATION IN SMALL
SEARCHING FROM PREVIOUS
INCREMENTS................................... 197
DESTINATIONS ................................ 214
3. MAP SCREEN INFORMATION ... 198 SEARCHING BY ADDRESS BOOK .... 214
DISPLAYING MAP INFORMATION .... 198 SEARCHING BY EMERGENCY .......... 215
DISPLAYING INFORMATION  SEARCHING BY INTERSECTION 
ABOUT THE ICON WHERE  AND FREEWAY ................................ 215
THE CURSOR IS SET ...................... 200 SEARCHING BY MAP ......................... 217
STANDARD MAP ICONS .................... 201 SEARCHING BY COORDINATES....... 217
4. TRAFFIC INFORMATION ............ 202 3. STARTING ROUTE 

DISPLAYING TRAFFIC  GUIDANCE................................ 218
INFORMATION ON THE MAP.......... 204 STARTING ROUTE GUIDANCE.......... 218
PAUSING GUIDANCE ......................... 221
188
8
1
NAVIGATION SYSTEM *
2
3 ROUTE GUIDANCE 5 SETUP 3
1. ROUTE GUIDANCE SCREEN..... 222 1. DETAILED NAVIGATION 

SCREEN FOR ROUTE GUIDANCE ... 222 SETTINGS................................. 241 4
ROUTE OVERVIEW............................ 223 SCREENS FOR NAVIGATION 
SETTINGS ........................................ 241
DURING FREEWAY DRIVING............ 224
5
WHEN APPROACHING  2. TRAFFIC SETTINGS................... 245
INTERSECTION ............................... 225
SCREEN FOR TRAFFIC 
TURN LIST SCREEN .......................... 226 SETTINGS ........................................ 245 6
TURN-BY-TURN ARROW SCREEN... 226 AUTO AVOID TRAFFIC....................... 246
MY TRAFFIC ROUTES ....................... 247
2. TYPICAL VOICE GUIDANCE
7
PROMPTS.................................. 227
3. EDITING ROUTE ......................... 228 TIPS FOR THE NAVIGATION 

6
SYSTEM 8
ADDING DESTINATIONS ................... 229
REORDERING DESTINATIONS......... 229
1. GPS (GLOBAL POSITIONING
DELETING DESTINATIONS ............... 229
SYSTEM)................................... 251 9
SETTING ROUTE PREFERENCES ... 229
LIMITATIONS OF 
SELECTING ROUTE TYPE ................ 230 THE NAVIGATION SYSTEM ............ 251
DETOUR SETTING ............................. 230
2. MAP DATABASE VERSION 
AND COVERED AREA ............. 253
4 MEMORY POINTS MAP INFORMATION ........................... 253
ABOUT THE MAP DATA ..................... 254
1. MEMORY POINTS SETTINGS .... 232
SETTING UP HOME ........................... 233
SETTING UP PRESET 
DESTINATIONS................................ 234
SETTING UP ADDRESS BOOK ......... 236
SETTING UP AREAS TO AVOID........ 238
DELETING PREVIOUS 
DESTINATIONS................................ 240
189
1. BASIC OPERATION
1. QUICK REFERENCE
MAP SCREEN
To display this screen, press the “APPS” button, then select “Navigation” on the
“Apps” screen.
No. Name Function Page
Indicates whether the map orientation is set to

2D North-up, 2D
north-up or heading-up. The letter(s) beside this
heading-up or 3D
symbol indicate the vehicle’s heading direction 194
heading-up sym-
(e.g. N for north). In 3D map, only a heading-up
bol
view is available.
Options button Select to display the “Navigation Options” screen. 192
“GPS” mark 
Shows that the vehicle is receiving signals from
(Global Position- 251
the GPS.
ing System)
Shows that traffic information is received. Select

to start voice guidance for traffic information.
Traffic indicator 202
When traffic information is received via HD, HD
mark is displayed on the right.
Scale indicator This figure indicates the map scale. 193
190
1. BASIC OPERATION
No. Name Function Page
Select to magnify or reduce the map scale. When

Zoom in/out but-
either button is selected, the map scale indicator 193
ton
bar appears at the bottom of the screen.
Current position
 Select to display the current position address.
button/voice 193
 Select to repeat voice guidance.
guidance button
Destination but-
Select to display the “Destination” screen. 205
ton
Indicates the speed limit on the current road.

Speed limit icon The display of the speed limit icon can be set to 198
on/off.
Displays the current street name, or the distance

with the estimated travel time/arrival time to the
Route informa-
destination. The route information bar fills from 222
tion bar
left to right as the vehicle progresses on the
route.
Select to change the display between the current

Route informa-
street name and the distance with the estimated 223
tion button
travel/arrival time.
8
NAVIGATION SYSTEM
191
1. BASIC OPERATION
NAVIGATION OPTIONS SCREEN
The navigation options allow you to change map configurations, display/hide POI
icons, and edit the navigation routes. To display the “Navigation Options” screen,
press the “APPS” button, select “Navigation” on the “Apps” screen, and select
“Options” on the map screen.
No. Function Page
Select to change the map configuration. 194
Select to change the displayed map information such as POI icons,

198
route trace, speed limit, etc.
Select to display the map version and coverage area. 253
Select to edit the set route. 228
Select to pause or resume route guidance. 221
Select to display the overview of the entire route. 223
192
1. BASIC OPERATION
2. MAP SCREEN OPERATION
CURRENT POSITION MAP SCALE

DISPLAY
1 Select or to change the
1 Press the “APPS” button. scale of the map screen.
 The scale indicator bar appears at the bot-

tom of the screen.
 Select and hold or to con-
3 Check that the current position map is tinue changing the scale of the map
screen.
displayed.
 The scale of the map screen can also be
changed by selecting the scale bar
directly. This function is not available while
driving.
8
INFORMATION
● The map scale is displayed above the
NAVIGATION SYSTEM
zoom in button at the bottom left of the
screen.
 To correct the current position manu-

ally:P.243
INFORMATION
● While driving, the current position mark
is fixed on the screen and the map
moves.
● The current position is automatically set
as the vehicle receives signals from the
GPS (Global Positioning System). If the
current position is not correct, it is auto-
matically corrected after the vehicle
receives signals from the GPS.
● After the battery disconnection, or on a
new vehicle, the current position may
not be correct. As soon as the system
receives signals from the GPS, the cor-
rect current position is displayed.
193
1. BASIC OPERATION
ORIENTATION OF THE MAP : North-up symbol

Regardless of the direction of vehicle trav-
The orientation of the map can be el, north is always up.
changed between 2D north-up, 2D
heading-up and 3D heading-up by se- : Heading-up symbol
lecting the orientation symbol dis- The direction of vehicle travel is always up.
played at the top left of the screen.
: 3D Heading-up symbol
1 Select , or . The direction of vehicle travel is always up.
 The letter(s) beside this symbol indicate
North-up screen
the vehicle’s heading direction (e.g. N for
north).
SWITCHING THE MAP MODE
1 Select “Options” on the map screen.
2 Select “Map Mode”.
Heading-up screen
3 Select the desired configuration but-
ton.
3D screen
No. Function Page
Select to display the single

195
map screen.
Select to display the dual

195
map screen.
Select to display the com-

196
pass mode screen.
Select to display the turn list

226
screen.
Select to display the free-

224
way exit list screen.
194
1. BASIC OPERATION
No. Function Page

Editing right map
Select to display the inter- The right side map can be edited.
section guidance screen or
225 1 Select any point on the right side map.
the guidance screen on the
freeway.
Select to display the turn-
226
by-turn arrow screen.
 Depending on the conditions, certain

screen configuration buttons cannot be
selected.
■MAP ONLY
No. Function Page
Select to change the orien-

194
tation of the map.
Select to display POI icons. 198
Select to show traffic infor-

202
■DUAL MAP mation.
8
Select to change the map
193
scale.
NAVIGATION SYSTEM
 When set to on, the indicator will illumi-
nate.
 The map on the left is the main map.
195
1. BASIC OPERATION
■COMPASS SCREEN SCROLL

Information about the destination, cur- OPERATION
rent position and a compass is dis-
played on the screen. Use the scroll feature to move the de-
sired point to the center of the screen
for looking at a point on the map that is
different from the current position.
INFORMATION
● The destination mark is displayed in the
direction of the destination. When driv-
ing, refer to the longitude and latitude No. Information/Function
coordinates, and the compass, to make
sure that the vehicle is headed in the Cursor mark
direction of the destination.
● When the vehicle travels out of the cov- Distance from the current position to
erage area, the guidance screen the cursor mark.
changes to the whole compass mode
Select to set as a destination.
screen.
When selecting “Go to ” on the
following map screen, the navigation
system performs a search for the
route. (P.218)
If a destination has already been set,
“Go to ” and “Add to Route” will
be displayed.
“Go to ”: Select to delete the ex-
isting destination(s) and set a new
one.
“Add to Route”: Select to add a
destination.
196
1. BASIC OPERATION
No. Information/Function ADJUSTING LOCATION IN

Select to register as a memory point. SMALL INCREMENTS
To change the icon, name, etc.:
P.236 The cursor location can be adjusted in
Select to return to the current posi-
small increments when “Adjust Loca-
tion. tion” is selected on the setting map
screen.
 To scroll over the map screen, place the
cursor mark in the desired position and
Also, when changing the location of
then press and hold the map screen. The memory points on the editing screen
map will continue scrolling in that direction (P.240) and adjusting the current po-
until the finger is released. sition mark manually on the “Calibra-
tion” screen (P.243), 8 directional
arrows may appear for this purpose.
1 Select one of the 8 directional arrows

to move the cursor to the desired point
and then select “OK”.
NAVIGATION SYSTEM
197
1. BASIC OPERATION
3. MAP SCREEN INFORMATION
DISPLAYING MAP SELECTING THE POI ICONS

INFORMATION 1 Display the “Map Information” screen.
(P.198)
Information such as POI icons, route
trace, speed limit, etc. can be dis- 2 Select “Select POI”.
played on the map screen.  When the POI icons to be displayed on
the map screen have already been set,
1 Select “Options” on the map screen. “Change POI” is displayed.
2 Select “Map Information”. 3 Select the desired POI category and
select “OK”.
3 Select the desired items to be dis-
played.
No. Information/Function Page
No. Function Page Displays up to 5 selected

POI icons on the map 
Select to display the select- screen

ed POI icons.
Select to cancel the select-

Select to select or change ed POI icons.
198
POI icons.
Displays up to 6 POI icons
242
Select to display route as favorite POI categories
200
trace.
Select to display other POI
Select to display speed limit categories if the desired
 199
icon. POIs cannot be found on
the screen.
Select to display traffic infor-
202
mation. Select to search for the
199
nearest POIs.
nate.
198
1. BASIC OPERATION
■SELECTING OTHER POI ICONS TO ■DISPLAYING THE LOCAL POI LIST

BE DISPLAYED
POIs that are within 20 miles (32 km) of
1 Select “Other POIs”. the current position will be listed from
2 Select the desired POI categories and among the selected categories.
select “OK”. 1 Select “Find Local POI”.
2 Select the desired POI.
“List All Categories”: Select to display all

POI categories. To add more POI catego-
ries, select “More”. “Near...”: Select to search for POIs near
the current position or along the route.
3 Check that the selected POI is dis-
played on the map screen. (P.196)
NAVIGATION SYSTEM
When “Near...” is selected

“Near Here”: Select to search for POIs
near the current position.
“Along My Route”: Select to search for
POIs along the route.
199
1. BASIC OPERATION
ROUTE TRACE DISPLAYING INFORMATION

ABOUT THE ICON WHERE
The traveled route can be stored and
retraced on the map screen. This fea-
THE CURSOR IS SET
ture is available when the map scale is
30 miles (50 km) or less. When the cursor is placed over an icon
on the map screen, the name bar is
1 Display the “Map Information” screen. displayed on the upper part of the
(P.198) screen. If “Info” appears on the right
side of the name bar, detailed informa-
2 Select “Route Trace”.
tion can be displayed.
 The “Route Trace” indicator illuminates
and the route trace starts. 1 Place the cursor over an icon.
3 Check that the traveled line is dis- 2 Select “Info”.
played.
POI information
■STOP RECORDING THE ROUTE
TRACE
1 Select “Route Trace” again.
2 A confirmation screen will be dis-

played. 
“Yes”: Select to keep the recorded
route trace.
“No”: Select to erase the recorded Memory point information
route trace.
INFORMATION
● The traveled route can be stored up to
124 miles (200 km).
200
1. BASIC OPERATION
Destination information
STANDARD MAP ICONS
Icon Name
Island
Park
No. Function Industry
Select to register as a memory point.

To change the icon, name, etc.: Business facility
P.236
Select to set as a destination. Airport
Select to call the registered number.

Military
Select to delete destination or mem-
ory point.
University
Select to display the edit memory
point screen.
Hospital 8
INFORMATION
NAVIGATION SYSTEM
Stadium
● Even when traffic information is not cur-
rently being received, traffic information
and “Info” will be displayed for a while Shopping mall
after traffic information has been
received.
Golf
201
1. BASIC OPERATION
4. TRAFFIC INFORMATION
Traffic data can be received via HD DISPLAYING TRAFFIC

Radio or Entune App Suite to display INFORMATION
traffic information on the map screen.
A list of current traffic information can
1 Press the “APPS” button. be displayed along with information on
the incident’s distance and position rel-
ative to the vehicle.
1 Display the “Traffic Information”

screen. (P.202)
2 Select “Traffic Event List”.
3 Select the desired traffic information.

“On Current Road”: Select to display traf-
fic information for the current road.
2 Select “Traffic”. “On Current Route”: Select to display
traffic information for the set route.
nate.
4 Check that the traffic information is dis-
played.
No. Function Page
Select to display a list of

202
current traffic information.
“Detail”: Select to display detailed traffic
Select to display a map
203 information.
with predictive traffic data.
Select to display traffic

203
along the saved routes.
202
1. BASIC OPERATION
DISPLAYING PREDICTIVE MY TRAFFIC ROUTES

TRAFFIC INFORMATION
Traffic information along the saved
A map with predictive traffic data can routes can be displayed. To use this
be displayed. function, it is necessary to register a
route. (P.247)
1 Display the “Traffic Information”
screen. (P.202) 1 Display the “Traffic Information”
screen. (P.202)
2 Select “Predictive Traffic Map”.
2 Select “My Traffic Routes”.
3 Scroll the map to the desired point and
 If map data has been updated, a confirma-
set the time of predictive traffic infor-
tion screen will be displayed. Select “OK”
mation. or “Do Not Tell Me Again”.
3 Select the desired route.
 The time of the predictive traffic informa-

tion can be displayed in 15-minute steps 8
up to +45 minutes. “Options”: Select to add, edit or delete
“+”: Moves the time forward 15 minutes.
NAVIGATION SYSTEM
my traffic routes.(P.247)
“-”: Moves the time back 15 minutes.  If routes have not been registered yet, a
confirmation screen will be displayed.
Select “Yes” to register the route.
4 Select the desired traffic information.
203
1. BASIC OPERATION
DISPLAYING TRAFFIC No. Information/Function

INFORMATION ON THE MAP The icons show traffic incident, road
repair, traffic obstacles, etc. Select to
1 Select “Options” on the map screen. display traffic information and start
voice guidance for the traffic informa-
2 Select “Map Information”. tion.
3 Select “Traffic Information”. The color of the arrow changes de-

 When set to on, the indicator will illumi- pending on the traffic information re-
nate. ceived.
4 Check that the traffic information is dis- The indicator is displayed as follows.
played. : Traffic information has
been received.
: Traffic information has

been received via HD.
No icon: Traffic information has not
been received.
204
2. DESTINATION SEARCH
1. DESTINATION SEARCH SCREEN
The “Destination” screen enables to search for a destination. To display the “Des-
tination” screen, select “Dest.” on the map screen.
8
No. Function Page
NAVIGATION SYSTEM
Select to search for a destination by address. 209
Select to search for a destination by point of interest. 210
Select to search for a destination from previously set destinations. 214
Select to search for a destination from a registered entry in “Address

214
Book”.
Select to search for a destination by online database. 265
Select to search for a destination from emergency service points. 215
Select to search for a destination by intersection or freeway entrance/

215
exit.
Select to search for a destination by the last displayed map. 217
Select to search for a destination by coordinates. 217
Select to set a destination by home. 208
205
No. Function Page
Select to set a destination from preset destinations. 208
Select to delete set destinations. 229
206
2. SEARCH OPERATION
1 Press the “APPS” button. 5 Select “Go” when the confirm destina-
tion screen is displayed.
No. Function
Select to adjust the position in small-
3 Select “Dest.”. er increments. (P.197)
4 Search for a destination. Select to register as a memory point.
Select to call the registered number.
Select to search for the route. 

(P.218)
If a destination has already been
set, “Go Directly” and “Add to
Route” will be displayed. 8
“Go Directly”: Select to delete the
existing destination(s) and set a new
NAVIGATION SYSTEM
search for a destination. (P.205) one.
“Add to Route”: Select to add a
destination.
207
SELECTING SEARCH AREA SETTING HOME AS

DESTINATION
The selected state (province) can be
changed to set a destination from a To use this function, it is necessary to
different state (province) by using register a home address. (P.233)
“Address”, “Point of Interest” or
“Intersection & Freeway”. 1 Display the “Destination” screen.
(P.207)
1 Display the “Destination” screen.
(P.207) 2 Select “Go Home”.
 The navigation system performs a search
2 Select “Address”, “Point of Interest” for the route and the entire route map is
or “Intersection & Freeway”. displayed. (P.218)
3 Select “Select State/Province” or

“Change State/Province”. SETTING PRESET
 If a state (province) has not been selected DESTINATIONS AS
yet, “Select State/Province” is dis- DESTINATION
played.
4 Select the desired state (province). To use this function, it is necessary to
register preset destinations to the
preset screen buttons (1-5). (P.234)

(P.207)
2 Select any of the preset destination
buttons (1-5).
 To change countries, select the “United

States”, “Canada” or “Mexico” tab.
 For map database information and
updates: P.253

for the route and the entire route map is
displayed. (P.218)
208
SEARCHING BY ADDRESS SEARCHING BY CITY
There are 2 methods to search for a

1 Select “City”.
destination by address. 2 Enter a city name and select “OK”.
1 Display the “Destination” screen. “Last 5 Cities”: Select the city name from
the list of the last 5 cities.
(P.207)
2 Select “Address”.
3 Select the desired city name.
3 Select the desired search method.

4 Enter a street name and select “OK”.
5 Select the desired street name.
6 Enter a house number and select

“OK”.
 If the same address exists, the address
list screen will be displayed. Select the
desired address.
No. Function Page
Select to search by city. 209

8
Select to search by street
210
address.
NAVIGATION SYSTEM
209
SEARCHING BY STREET SEARCHING BY POINT OF

ADDRESS INTEREST
1 Select “Street Address”.
There are 3 methods to search for a
2 Enter a house number and select destination by Points of Interest.
“OK”.
3 Enter a street name and select “OK”. (P.207)
4 Select the desired street name. 2 Select “Point of Interest”.
5 Enter a city name and select “OK”. 3 Select the desired search method.
 If the same address exists, the address
list screen will be displayed. Select the
desired address.
INFORMATION
● A street name can be searched using
only the body part of its name.
For example: S WESTERN AVE
No. Function Page
• A search can be performed by entering
“S WESTERN AVE”, “WESTERN AVE” Select to search by name. 211
or “WESTERN”.
Select to search by catego-
212
ry.
Select to search by phone

213
number.
210
SEARCHING BY NAME ■SELECTING A CITY TO SEARCH
1 Select “Name”.
1 Select “City”.
2 Enter a POI name and select “OK”.

2 Enter a city name and select “OK”.
“Any City”: Select to cancel the city set-
3 Select the desired POI. ting.
■SELECTING FROM THE CATEGO-

RIES
1 Select “Category”.
No. Function Page

2 Select the desired category.
Select to search for POI in

211
the desired city.
Select to search for POI

211
from the category list.
 When entering the name of a specific POI, 8

and there are 2 or more sites with the
same name, the list screen will be dis-
 If there is more than 1 detailed item of the
NAVIGATION SYSTEM
played. Select the desired POI.
selected category, the detailed list will be
displayed.
INFORMATION
● To search for a facility name using multi- POI categories.
ple search words, put a space between
each word. 3 Select the desired POI.
211
SEARCHING BY CATEGORY 3 Select the desired POI category.
1 Select “Category”.
2 Select the desired search point.
 If there is more than 1 detailed item of the

selected category, the detailed list will be
displayed.
No. Function POI categories.
“Favorite POI Categories”: Select to use
Select to set the search point from the 6 POIs that have been previously
near the current position.
set.(P.242)
Select to search for POIs along the
set route.
Select to set the search point from INFORMATION

near a city center. (P.213)
● The names of POIs located within
Select to set the search point from approximately 200 miles (320 km) from
near a destination. the selected search point can be dis-
played.
212
When “Near a City Center in (area SEARCHING BY PHONE

name)” is selected
NUMBER
1 Select “Near a City Center in (area
name)”. 1 Select “Phone #”.
2 Enter a city name and select “OK”. 2 Enter a phone number and select
“OK”.
“Last 5 Cities”: Select the city name from
the list of the last 5 cities.  If there is more than 1 site with the same
number, the list screen will be displayed.
INFORMATION
4 Select “OK” when the city center map
● If there is no match for the entered
screen is displayed. phone number, a list of identical num-
5 Follow the steps from 3 onward in bers with different area codes will be dis-
played.
“SEARCHING BY CATEGORY”.
(P.212)
INFORMATION
● If the navigation system has never been
used, selecting the city name from “Last
5 Cities” will not be available.
NAVIGATION SYSTEM
213
SEARCHING FROM SEARCHING BY ADDRESS

PREVIOUS DESTINATIONS BOOK
1 Display the “Destination” screen. To use this function, it is necessary to

(P.207) register an address book entry.
2 Select “Previous Destinations”.
(P.236)
3 Select the desired destination. 1 Display the “Destination” screen.

(P.207)
2 Select “Address Book”.
3 Select the desired address book entry.
“Previous Start Point”: Select to display

the start point map of the previous guided
route.
“Delete”: Select to delete the previous
destination. (P.240)  “Options”: Select to register or edit
address book entries. (P.236)
INFORMATION
● The previous start point and up to 100
previously set destinations are displayed
on the screen.
214
SEARCHING BY SEARCHING BY
EMERGENCY INTERSECTION AND
FREEWAY
(P.207) There are 2 methods to search for a
2 Select “Emergency”. destination by Intersection & Freeway.
3 Select the desired emergency catego- 1 Display the “Destination” screen.

ry. (P.207)
2 Select “Intersection & Freeway”.
3 Select the desired method.
4 Select the desired destination.
INFORMATION
● The navigation system does not guide in No. Function Page
8
areas where route guidance is unavail-
able. (P.252) Select to search by inter-
216
section.
NAVIGATION SYSTEM
Select to search by free-
216
way entrance/exit.
215
SEARCHING BY SEARCHING BY FREEWAY

INTERSECTION ENTRANCE/EXIT
1 Select “Intersection”. 1 Select “Freeway Entrance/Exit”.
2 Enter the name of the first intersecting 2 Enter a freeway name and select
street which is located near the desti- “OK”.
nation and select “OK”.
3 Select the desired freeway.
4 Select “Entrance” or “Exit”.
4 Enter the name of the second inter-

secting street and select “OK”.
5 Enter a freeway entrance or exit name
and select “OK”.
6 Select the desired entrance or exit
 If the 2 streets cross at more than 1 inter-
section in a city, the list of intersections will name.
be displayed.
INFORMATION
● Be sure to use the complete name of the
freeway or highway, including the
hyphen, when entering the destination.
Freeways and interstates use an “I” (I-
405). US highways use the state desig-
nation before the number (CA-118).
216
SEARCHING BY MAP SEARCHING BY

COORDINATES
By selecting “Map” the last displayed
location is displayed again on the map 1 Display the “Destination” screen.
screen. You can search for a destina- (P.207)
tion from this map.
2 Select “Coordinates”.
3 Enter the latitude and longitude and
(P.207)
select “OK”.
2 Select “Map”.

select “Go to ”.
“Adjust Location”: Select to adjust the 8

position in smaller increments. (P.197)
 If a destination has already been set, “Go
NAVIGATION SYSTEM
to ” and “Add to Route” will be dis-
played.
“Go to ”: Select to delete the existing
destination(s) and set a new one.
“Add to Route”: Select to add a destina-
tion.
for the route and the entire route map is
displayed. (P.218)
217
3. STARTING ROUTE GUIDANCE
When the destination is set, the entire CAUTION

route map from the current position to
the destination is displayed. ● Be sure to obey traffic regulations and
keep road conditions in mind while driv-
ing. If a traffic sign on the road has been
STARTING ROUTE changed, the route guidance may not
GUIDANCE indicate such changed information.
1 Select “OK” to start guidance.

INFORMATION
● The route for returning may not be the
same as that for going.
● The route guidance to the destination
may not be the shortest route or a route
without traffic congestion.
● Route guidance may not be available if
there is no road data for the specified
location.
● When setting the destination on a map
No. Information/Function with a scale more than 0.5 mile (800 m),
the map scale changes to 0.5 miles (800
Select the desired route from 3 pos- m) automatically. If this occurs, set the
sible routes. (P.219) destination again.
Select to change the route. ● If a destination that is not located on a
(P.220) road is set, the vehicle will be guided to
the point on a road nearest to the desti-
Select to display a list of the turns re- nation. The road nearest to the selected
quired to reach the destination. point is set as the destination.
(P.220)
Current position
Destination point
Type of route and its distance
Distance of the entire route
Select to start guidance.

If “OK” is selected and held until a
beep sounds, demo mode will start.
Press the “HOME” or “APPS” but-
ton to end demo mode.
218
3 ROUTES SELECTION ■DISPLAYING 3 ROUTES INFORMA-

TION
1 Select “3 Routes”.
1 Select “Info”.
2 Select the desired route.
2 Check that the “3 Routes Information”
screen is displayed.
No. Function
Select to display the quickest route. No. Information
Select to display the route that is the Time necessary for the entire trip
shortest distance to the set destina-
tion. Distance of the entire trip
Select to display the alternative Distance of the toll road

route.
Distance of the freeway 8
Select to display the information
about the 3 routes. (P.219)
NAVIGATION SYSTEM
Distance of the ferry trip
219
DISPLAYING TURN LIST EDITING ROUTE
A list of turn information from the cur- Destinations can be added, reordered
rent position to the destination can be or deleted, and conditions for the route
displayed. to the destination can be changed.
1 Select “Turn List”. 1 Select “Edit Route”.
2 Check that the turn list is displayed. 2 Select the desired item.
No. Information No. Function Page
Current position Select to add destinations. 229
Distance to the next turn Select to delete destina-

229
tions.
Turn direction at the intersection
Select to reorder destina-
229
tions.
Select to display the map of the se-
lected point. Select to set route prefer-
229
ences.
INFORMATION Select to change route
230
● However, not all road names on the type.
route may appear on the list. If a road
changes its name without requiring a Select to set detours. 230
turn (such as on a street that runs
through 2 or more cities), the name
change will not appear on the list. The INFORMATION
street names will be displayed in order ● Even if the “Freeways” indicator is
from the starting point, along with the dimmed, the route cannot avoid includ-
distance to the next turn. ing a freeway in some cases. (P.229)
● If the calculated route includes a trip by
ferry, the route guidance shows a sea
route. After traveling by ferry, the current
position may be incorrect. Upon recep-
tion of GPS signals, it is automatically
corrected.
220
PAUSING GUIDANCE
1 Select “Options” on the map screen.
2 Select “Pause Guidance”.
RESUMING GUIDANCE
1 Select “Resume Guidance”.
NAVIGATION SYSTEM
221
3. ROUTE GUIDANCE
1. ROUTE GUIDANCE SCREEN
During the route guidance, various CHANGING ROUTE

types of guidance screens can be dis- INFORMATION BAR
played depending on conditions.
When the vehicle is on the guidance
route, the route information bar dis-
SCREEN FOR ROUTE plays the current street name or the
GUIDANCE distance with the estimated travel/ar-
rival time to the destination.
1 Select the route information bar ( )

or the route information button ( ) to
change the display of the route infor-
mation bar.
No. Information/Function
Distance to the next turn and an ar-

row indicating the turning direction
Guidance route
Current position No. Information/Function
Select to change the display be-

Current street name or route infor-
tween the estimated travel time and
mation
the estimated arrival time.
Select to change the display be-

INFORMATION
tween the current street name and
● If the vehicle goes off the guidance the distance with the estimated trav-
route, the route is searched again. el/arrival time.
● For some areas, the roads have not
been completely digitized in our data-
base. For this reason, the route guid- INFORMATION
ance may select a road that should not ● When the vehicle is on the guidance
be traveled on. route, the distance measured along the
● When arriving at the set destination the route is displayed. Travel time and
destination name will be displayed on arrival time are calculated based on the
the upper part of the screen. average speed for the specified speed
limit.
● When the vehicle gets off the guidance
route, the arrow facing the destination is
displayed instead of the estimated
travel/arrival time.
● The route information bar fills from left to
right as the vehicle progresses on the
route.
222
3. ROUTE GUIDANCE
DISTANCE AND TIME TO ROUTE OVERVIEW

DESTINATION
The entire route from the current posi-
When driving on the guidance route tion to the destination can be displayed
with more than 1 destination set, a list during the route guidance.
of the distance with estimated travel/
arrival time from the current position to 1 Select “Options” on the map screen.
each destination is displayed.
2 Select “Route Overview”.
1 Select the route information bar.
3 Check that the entire route map is dis-
2 Check that the list of the distance and played.
time is displayed.
 For details about this screen: P.218

 By selecting one of the number buttons,
the desired route information is displayed. 8
NAVIGATION SYSTEM
223
3. ROUTE GUIDANCE
DURING FREEWAY DRIVING WHEN APPROACHING

FREEWAY EXIT OR JUNCTION
During freeway driving, the freeway
exit information screen will be dis- When the vehicle approaches an exit
played. or junction, the freeway guidance
screen will be displayed.
No./
Information/Function No. Information/Function
Icon
Distance and time from the current Next exit or junction name
position to the freeway exit/rest ar-
ea. Distance from the current position to
the exit or junction
Name of the freeway exit/rest area.
Select to hide the freeway guidance
screen. To return to the freeway
POIs that are close to a freeway exit.
guidance screen, select .
Select to display the selected map of
the exit vicinity. Remaining distance bar to the guid-
ance point
Select to display the nearest free-
way exit/rest area from the current
position.
Select to scroll to farther freeway

exit/rest area.
Select to scroll to closer freeway

exit/rest area.
224
3. ROUTE GUIDANCE
TOLLGATE GUIDANCE WHEN APPROACHING

INTERSECTION
When the vehicle approaches a toll-
gate, the tollgate view will be dis-
When the vehicle approaches an inter-
played.
section, the intersection guidance
screen will be displayed.
Distance from the current position to No. Information/Function

the tollgate
Next street name
Select to hide the tollgate guidance
screen. To return to the tollgate Distance to the intersection
guidance screen, select .
Select to hide the intersection guid-
ance screen. To return to the inter- 8
Remaining distance bar to the guid-
ance point section guidance screen, select
NAVIGATION SYSTEM
.
Remaining distance bar to the guid-

ance point
225
3. ROUTE GUIDANCE
TURN LIST SCREEN TURN-BY-TURN ARROW

SCREEN
1 Select “Turn List” on the “Map Mode”
screen. (P.194) On this screen, information about the
2 Check that the turn list screen is dis- next turn on the guidance route can be
played. displayed.
1 Select “Turn-by-Turn Arrow” on the

“Map Mode” screen. (P.194)
2 Check that the turn-by-turn arrow
screen is displayed.
Turn direction
Distance between turns
Next street or destination name
Exit number or street name
Turn direction
Distance to the next turn
226
3. ROUTE GUIDANCE
2. TYPICAL VOICE GUIDANCE PROMPTS
As the vehicle approaches an intersec-

tion, or point, where maneuvering the
vehicle is necessary, the system’s
voice guidance will provide various
messages.
CAUTION
● Be sure to obey the traffic regulations
and keep the road condition in mind
especially when you are driving on IPD
roads. The route guidance may not have
the updated information such as the
direction of a one way street.
INFORMATION
● If a voice guidance command cannot be
heard, select on the map screen
to hear it again.
● To adjust the voice guidance volume: 
P.61
● Voice guidance may be made early or 8
late.
● If the system cannot determine the cur-
NAVIGATION SYSTEM
rent position correctly, you may not hear
voice guidance or may not see the mag-
nified intersection on the screen.
227
3. ROUTE GUIDANCE
3. EDITING ROUTE
1 Press the “APPS” button. 5 Select the item to be set.
No. Function Page
2 Select “Navigation”. Select to add destinations. 229
3 Select “Options”. Select to delete destina-

229
tions.
4 Select “Edit Route”.
Select to reorder destina-
229
tions.
Select to set route prefer-

229
ences.
Select to change route

230
type.
Select to set detours. 230
6 Check that the entire route map is dis-

played. (P.218)
228
3. ROUTE GUIDANCE
ADDING DESTINATIONS DELETING DESTINATIONS
1 Display the “Edit Route” screen. 1 Display the “Edit Route” screen.
(P.228) (P.228)
2 Select “Add”. 2 Select “Delete”.
3 Search for an additional destination in 3 Select “Yes” when the confirmation

the same way as a destination search. screen appears.
(P.205)  When more than 1 destination has been
set, a list will be displayed on the screen.
4 Select “Add Destination Here” to in- Select the item(s) to be deleted.
sert the new destination into the route. “Delete All”: Select to delete all destina-
tions on the list.
 If more than 1 destination has been set,
the system will recalculate the route(s) to
the set destination(s) as necessary.
SETTING ROUTE
PREFERENCES
The conditions to determine the route

REORDERING
can be selected from various choices 8
DESTINATIONS such as freeways, toll roads, ferries,
etc.
NAVIGATION SYSTEM
When more than 1 destination has
been set, the arrival order of the desti- 1 Display the “Edit Route” screen.
nations can be changed. (P.228)
1 Display the “Edit Route” screen. 2 Select “Preferences”.

(P.228) 3 Select the desired route preferences
2 Select “Reorder”. and select “OK”.
3 Select the desired destination and se-

lect “Move Up” or “Move Down” to
change the arrival order. Then select
“OK”.

nate.
229
3. ROUTE GUIDANCE
SELECTING ROUTE TYPE DETOUR SETTING
1 Display the “Edit Route” screen. During the route guidance, the route
(P.228) can be changed to detour around a
2 Select “Route Type”.
section of the route where a delay is
caused by road repairs, an accident,
3 Select the desired route type. etc.
1 Display the “Edit Route” screen.

(P.228)
2 Select “Detour”.
3 Select the desired detour distance.
 During driving, the route guidance starts

after selecting the desired route type.
4 The entire route from the starting point
to the destination is displayed.
 For details about this screen: P.218
No. Function
Select to detour within 1 mile of the

current position.
Select to detour within 3 miles of the

current position.
Select to detour within 5 miles of the

current position.
Select to detour on the entire route.
Select to make the system search

for the route based on traffic con-
gestion information received from
traffic information. (P.202)
230
3. ROUTE GUIDANCE
INFORMATION
● This picture shows an example of how

the system would guide around a delay
caused by a traffic jam.
This position indicates the location of a
traffic jam caused by road repairs, an
accident, etc.
This route indicates the detour sug-
gested by the system.
● When the vehicle is on a freeway, the
detour distance selections are 5, 15 and
25 miles (or 5, 15 and 25 km if units are
in km).
● The system may not be able to calculate 8
a detour route depending on the
selected distance and surrounding road
NAVIGATION SYSTEM
conditions.
231
4. MEMORY POINTS
1. MEMORY POINTS SETTINGS
Home, preset destinations, address 4 Select the desired item to be set.

book entries, areas to avoid can be set
as memory points. The registered
points can be used as the destinations.
(P.205)
Registered areas to avoid, will be
avoided when the system searches for
a route.

No. Function Page
Select to set home. 233
Select to set preset desti-

234
nations.
Select to set the address

236
book.
Select to set areas to

238
avoid.
Select to delete previous

destinations.
240
3 Select “Navigation”. Select to set detailed navi-

241
gation settings.
232
4. MEMORY POINTS
SETTING UP HOME EDITING HOME
If home has been registered, that infor-

1 Select “Edit”.
mation can be recalled by selecting 2 Select the desired item to be edited.
“Go Home” on the “Destination”
screen. (P.208)
1 Display the “Navigation Settings”

screen. (P.232)
2 Select “Home”.
No. Function Page
Select to edit the home

238
name.
Select to set display of the


home name on/off.
Select to edit location infor-

238
mation.
No. Function Page 8
Select to edit the phone
238
number.
Select to register home. 233
NAVIGATION SYSTEM
Select to change the icon
Select to edit home. 233 to be displayed on the map 237
screen.
Select to delete home. 233

3 Select “OK”.
REGISTERING HOME DELETING HOME
1 Select “Set Home”. 1 Select “Delete”.
2 Select the desired item to search for 2 Select “Yes” when the confirmation
the location. (P.205) screen appears.
3 Select “OK” when the editing home

screen appears.
233
4. MEMORY POINTS
SETTING UP PRESET REGISTERING PRESET

DESTINATIONS DESTINATIONS
1 Select “Set”.
If a preset destination has been regis-
tered, that information can be recalled 2 Select the desired item to search for
by using preset destinations on the the location. (P.205)
“Destination” screen. (P.208)
3 Select a position for this preset desti-
1 Display the “Navigation Settings” nation.
screen. (P.232)
2 Select “Preset Destinations”.
4 Select “OK” when the editing preset

destination screen appears. (P.235)
INFORMATION
No. Function Page ● Up to 5 preset destinations can be regis-

tered.
Select to register a preset
234
destination.
Select to edit a preset des-

235
tination.
Select to delete a preset

235
destination.
234
4. MEMORY POINTS
EDITING PRESET DELETING PRESET

DESTINATIONS DESTINATIONS
1 Select “Edit”. 1 Select “Delete”.
2 Select the desired preset destination. 2 Select the preset destination to be de-
leted and select “Delete”.
3 Select the item to be edited.

No. Function Page screen appears.
Select to edit the preset
238
destination name.
Select to set display of the

preset destination name 
on/off. 8
238
NAVIGATION SYSTEM
mation.
Select to edit the phone

238
number.
Select to change the icon

to be displayed on the map 237
screen.
4 Select “OK”.
235
4. MEMORY POINTS
SETTING UP ADDRESS EDITING ADDRESS BOOK

BOOK ENTRIES
The icon, name, location and/or phone

Points on the map can be registered.
number of a registered address book
1 Display the “Navigation Settings” entry can be edited.
screen. (P.232)
2 Select “Address Book”.
2 Select the desired address book entry.
3 Select the item to be edited.
No. Function Page

No. Function Page
Select to register address
236 Select to edit the address
book entries. 238
book entry name.
Select to edit address book
236 Select to set display of the
entries.
address book entry name 
Select to delete address on/off.
238
book entries.
238
mation.
REGISTERING ADDRESS Select to edit the phone
BOOK ENTRIES 238
number.
1 Select “New”. Select to change the icon

to be displayed on the map 237
2 Select the desired item to search for screen.
3 Select “OK” when the editing address 4 Select “OK”.
book entry screen appears. (P.236)
INFORMATION
● Up to 100 address book entries can be
registered.
236
4. MEMORY POINTS
■CHANGING THE ICON When the “With Sound” tab is selected
1 Select “Edit” next to the “Icon”. A sound for some address book entries
can be set. When the vehicle ap-
2 Select the desired icon.
proaches the location of the address
book entry, the selected sound will be
heard.
1 Select the “With Sound” tab.
2 Select the desired sound icon.
: Select to play the sound.

 When “Bell (with Direction)” is selected,
 Change pages by selecting the “Page 1”,
select an arrow to adjust the direction and
“Page 2” or “With Sound” tab.
select “OK”.
“With Sound”: Select the memory points
with a sound
INFORMATION
NAVIGATION SYSTEM
● The bell sounds only when the vehicle
approaches this point in the direction
that has been set.
237
4. MEMORY POINTS
■CHANGING THE NAME SETTING UP AREAS TO

1 Select “Edit” next to “Name”. AVOID
2 Enter a name and select “OK”.
Areas to be avoided because of traffic
■CHANGING THE LOCATION jams, construction work or other rea-
sons can be registered as “Areas to
1 Select “Edit” next to “Location”. Avoid”.
2 Scroll the map to the desired point 1 Display the “Navigation Settings”
(P.197) and select “OK”. screen. (P.232)
■CHANGING PHONE NUMBER 2 Select “Areas to Avoid”.
1 Select “Edit” next to “Phone #”. 3 Select the desired item.
2 Enter the phone number and select

“OK”.
DELETING ADDRESS BOOK

ENTRIES
2 Select the item to be deleted and select No. Function Page

“Delete”.
Select to register areas to
239
avoid.
Select to edit areas to

239
avoid.
Select to delete areas to

240
avoid.

screen appears.
238
4. MEMORY POINTS
REGISTERING AREAS TO EDITING AREAS TO AVOID

AVOID
The name, location and/or area size of
1 Select “New”. a registered area can be edited.
2 Select the desired item to search for 1 Select “Edit”.
2 Select the area and select “OK”.
3 Select either or to 3 Select the item to be edited.
change the size of the area to be avoid-
ed and select “OK”.
No. Function Page
4 Select “OK” when the editing area to Select to edit the name of
240
avoid screen appears. the area to avoid.
Select to set display of the 8

INFORMATION 
area to avoid name on/off.
● If a destination is entered in the area to
NAVIGATION SYSTEM
avoid or the route calculation cannot be Select to edit area location. 240
made without running through the area
to avoid, a route passing through the Select to edit area size. 240
area to be avoided may be shown.
● Up to 10 locations can be registered as Select to set the area to

points/areas to avoid. avoid function on/off.
4 Select “OK”.
239
4. MEMORY POINTS
■CHANGING THE NAME DELETING AREAS TO AVOID

1 Select “Edit” next to “Name”.
2 Enter a name and select “OK”.
2 Select the area to be deleted and se-
■CHANGING THE LOCATION lect “Delete”.
1 Select “Edit” next to “Location”. 3 Select “Yes” when the confirmation

screen appears.
2 Scroll the map to the desired point
(P.197) and select “OK”.
DELETING PREVIOUS
■CHANGING THE AREA SIZE DESTINATIONS
1 Select “Edit” next to “Size”. Previous destinations can be deleted.
2 Select either or to 1 Display the “Navigation Settings”

change the size of the area to be avoid- screen. (P.232)
ed and select “OK”.
2 Select “Delete Previous Dest.”.
3 Select the previous destination to be

deleted and select “Delete”.

screen appears.
240
5. SETUP
1. DETAILED NAVIGATION SETTINGS
Settings are available for pop-up infor- SCREENS FOR NAVIGATION

mation, favorite POI categories, etc. SETTINGS
4 Select “Detailed Navi. Settings”.
NAVIGATION SYSTEM
241
5. SETUP
No. Function Page FAVORITE POI CATEGORIES

(SELECT POI ICONS)
Select to set the voice guid-
ance for the next street 
name on/off. Up to 6 POI icons, which are used for
selecting POIs on the map screen, can
Select to set IPD road guid- be selected as favorites.

ance on/off.
Select to set favorite POI

1 Display the “Detailed Navi. Settings”
categories that are used for screen. (P.241)
242
POI selection to display on
the map screen.
2 Select “Favorite POI Categories”.
Select to adjust the current

3 Select the category to be changed.
position mark manually or
to adjust miscalculation of 243
the distance caused by tire
replacement.
Select to set display of pop-


up information on/off.
Select to reset all setup


items.
“Default”: Select to set the default catego-
ries.
4 Select the desired POI category.
POI categories.
5 Select the desired POI icon.
242
5. SETUP
CURRENT POSITION/TIRE ■POSITION/DIRECTION CALIBRA-

CHANGE CALIBRATION TION
The current position mark can be ad- When driving, the current position
justed manually. Miscalculation of the mark will be automatically corrected by
distance caused by tire replacement GPS signals. If GPS reception is poor
can also be adjusted. due to location, the current position
mark can be adjusted manually.
1 Display the “Detailed Navi. Settings”
screen. (P.241) 1 Select “Position/Direction”.
2 Select “Calibration”. 2 Scroll the map to the desired point

(P.197) and select “OK”.
3 Select an arrow to adjust the direction
of the current position mark and select
“OK”.
 For additional information on the accu- 8

racy of a current position: P.251
NAVIGATION SYSTEM
243
5. SETUP
■TIRE CHANGE CALIBRATION

The tire change calibration function will
be used when replacing the tires. This
function will adjust miscalculation
caused by the circumference differ-
ence between the old and new tires.
1 Select “Tire Change”.

 The message appears and the quick dis-
tance calibration starts automatically.
INFORMATION
● If this procedure is not performed when
the tires are replaced, the current posi-
tion mark may be incorrectly displayed.
244
5. SETUP
2. TRAFFIC SETTINGS
Traffic information such as traffic con- SCREEN FOR TRAFFIC

gestion or traffic incident warnings can SETTINGS
be made available.
3 Select “Traffic”.
No. Function
Select to set specific routes (such as 8

frequently used routes) on which
you wish to receive traffic informa-
NAVIGATION SYSTEM
tion. (P.247)
Select to set the avoid traffic func-

tion auto/manual. (P.246)
Select to set the usage of traffic in-

formation for the estimated arrival
time on/off.
Select to set the display of an arrow

of free flowing traffic on/off.
Select to set to on/off whether to

consider the predictive traffic infor-
mation (P.203) with estimated ar-
rival time and detoured route
search.
Select to set of traffic incident voice

warning on/off.
245
5. SETUP
AUTO AVOID TRAFFIC ■CHANGING THE ROUTE

MANUALLY
1 Display the “Traffic Settings” screen.
When the navigation system calcu-
(P.245)
lates a new route, the following screen
2 Select “Avoid Traffic”. will be displayed.
3 Select the desired item. 1 Select the desired item.
No. Function No. Function
Select to automatically change Select to start route guidance using

routes when congestion information the new route.
of the guidance route has been re-
ceived. Select to confirm the new route and
current route on the map.
Select to select manually whether or
not to change routes when conges- Select to continue the current route
tion information of the guidance guidance.
route has been received. In this
mode, a screen will appear to ask if
you wish to reroute.
Select to not reroute when conges-

tion information for the guidance
route has been received.
4 Select “OK”.
246
5. SETUP
MY TRAFFIC ROUTES REGISTERING PERSONAL

ROUTES
Specific routes (such as frequently
used routes) on which you wish to re-
1 Select “New”.
ceive traffic information can be regis- 2 Select “Edit” next to “Name”.
tered as “My Traffic Routes”. A route is
set by defining a start point and end
point, and can be adjusted by setting
up to 2 preferred roads.
1 Display the “Traffic Settings” screen.

(P.245)
2 Select “My Traffic Routes”.
3 Select the desired item. 3 Enter the name and select “OK”.
4 Select “Edit” next to “Start”.
5 Select the desired item to search for

NAVIGATION SYSTEM
No. Function Page
Select to register personal

247
routes
Select to edit personal 6 Select “Edit” next to “End”.

248
routes
7 Select the desired item to search for
Select to delete personal the location. (P.205)
248
routes
8 Select “OK” when the editing traffic
route screen appears.
 The routes can be adjusted by setting pre-
ferred roads. (P.249)
INFORMATION
● Up to 5 routes can be registered.
247
5. SETUP
EDITING PERSONAL ROUTES DELETING PERSONAL

ROUTES
2 Select the desired traffic route.
2 Select the traffic route to be deleted
and select “Delete”.
3 Select “Edit” next to the item to be ed-

ited.
screen appears.
No. Function Page
Select to edit the name of

personal routes
Select to edit start location 247
Select to edit end location
Select to see and modify


the entire route.
4 Select “OK”.
 The entire route map will be displayed.
248
5. SETUP
SETTING PREFERRED ROADS ■ADDING PREFERRED ROADS

1 Select “Add”.
“My Traffic Routes” can be adjusted by
 If two preferred roads are already set,
setting up to 2 preferred roads.
select “Yes” and delete a preferred road
before add a new one.
1 Select “Set Preferred Roads”.
select “OK”.
3 Select “OK” to use this road.

 “Next”: Select to change road.
4 Select “Add Here” for the desired lo-
cation.
NAVIGATION SYSTEM
No. Function Page
Select to add preferred

249
roads.
Select to modify preferred

250
roads.  If a preferred road is already set, a second
Select to delete preferred preferred road can be added anywhere
250 between the start point, the end point and
roads.
the existing preferred road.
249
5. SETUP
■MODIFYING PREFERRED ROADS ■DELETING PREFERRED ROADS

1 Select “Modify”. 1 Select “Delete”.
2 Select the preferred road to be modi- 2 Select the preferred road to be deleted.
fied.
“Delete All”: Select to delete all preferred

3 Scroll the map to the desired point and roads on the list.
select “OK”. 3 Select “Yes” when the confirmation
screen appears.
4 Select “OK” to use this road.

 “Next”: Select to change road.
250
6. TIPS FOR THE NAVIGATION SYSTEM
1. GPS (GLOBAL POSITIONING SYSTEM)
When the vehicle is receiving signals from

LIMITATIONS OF THE satellites, the “GPS” mark appears at the
NAVIGATION SYSTEM top left of the screen.
The GPS signal may be physically ob-
This navigation system calculates the structed, leading to inaccurate vehicle po-
current position using satellite signals, sition on the map screen. Tunnels, tall
various vehicle signals, map data, etc. buildings, trucks, or even the placement of
However, an accurate position may not objects on the control panel may obstruct
be shown depending on satellite condi- the GPS signals.
tions, road configuration, vehicle con- The GPS satellites may not send signals
dition or other circumstances. due to repairs or improvements being
The Global Positioning System (GPS) de- made to them.
veloped and operated by the U.S. Depart- Even when the navigation system is re-
ment of Defense provides an accurate ceiving clear GPS signals, the vehicle po-
current position, normally using 4 or more sition may not be shown accurately or
satellites, and in some case 3 satellites. inappropriate route guidance may occur in
The GPS system has a certain level of in- some cases.
accuracy. While the navigation system
compensates for this most of the time, oc- NOTICE
casional positioning errors of up to 300 ft.
(100 m) can and should be expected. Gen- ● The installation of window tinting may
erally, position errors will be corrected obstruct the GPS signals. Most window
tinting contains some metallic content 8
within a few seconds.
that will interfere with GPS signal recep-
tion of the antenna in the instrument
NAVIGATION SYSTEM
panel. We advise against the use of win-
dow tinting on vehicles equipped with
navigation systems.
251
 Accurate current position may not be  Inappropriate route guidance may occur in
shown in the following cases: the following cases:
• When driving on a small angled Y- • When turning at an intersection off the
shaped road. designated route guidance.
• When driving on a winding road. • If you set more than 1 destination but
• When driving on a slippery road such as skip any of them, auto reroute will dis-
in sand, gravel, snow, etc. play a route returning to the destination
• When driving on a long straight road. on the previous route.
• When freeway and surface streets run in • When turning at an intersection for which
parallel. there is no route guidance.
• After moving by ferry or vehicle carrier. • When passing through an intersection
• When a long route is searched during for which there is no route guidance.
high speed driving. • During auto reroute, the route guidance
• When driving without setting the current may not be available for the next turn to
position calibration correctly. the right or left.
• After repeating a change of direction by • During high speed driving, it may take a
going forward and backward, or turning long time for auto reroute to operate. In
on a turntable in a parking lot. auto reroute, a detour route may be
• When leaving a covered parking lot or shown.
parking garage. • After auto reroute, the route may not be
• When a roof carrier is installed. changed.
• When driving with tire chains installed. • If an unnecessary U-turn is shown or
• When the tires are worn. announced.
• After replacing a tire or tires. • If a location has multiple names and the
• When using tires that are smaller or system announces 1 or more of them.
larger than the factory specifications. • When a route cannot be searched.
• When the tire pressure in any of the 4 • If the route to your destination includes
tires is not correct. gravel, unpaved roads or alleys, the
route guidance may not be shown.
 If the vehicle cannot receive GPS sig- • Your destination point might be shown
nals, the current position can be on the opposite side of the street.
adjusted manually. For information on • When a portion of the route has regula-
setting the current position calibration: tions prohibiting the entry of the vehicle
P.243 that vary by time or season or other rea-
sons.
• The road and map data stored in the
navigation system may not be complete
or may not be the latest version.
 After replacing a tire: P.244
INFORMATION
● This navigation system uses tire turning
data and is designed to work with fac-
tory-specified tires for the vehicle.
Installing tires that are larger or smaller
than the originally equipped diameter
may cause inaccurate display of the cur-
rent position. The tire pressure also
affects the diameter of the tires, so make
sure that the tire pressure of all 4 tires is
correct.
252
2. MAP DATABASE VERSION AND COVERED AREA
MAP INFORMATION 5 Check that the map data screen is dis-

played.
Coverage areas and legal information
can be displayed and map data can be
updated.
No. Function
Map version
Select to display map coverage ar-

eas.
Select to display legal information.

3 Select “Options”. INFORMATION

● Map data updates are available for a
4 Select “Map Data”.
fee. Contact your Toyota dealer for fur-
8
ther information.
NAVIGATION SYSTEM
253
ABOUT THE MAP DATA NOTICE
Map data for the navigation system is ● Failure to follow the precautions below
may result in damage to the SD cards or
contained in a SD card that is inserted
the SD card slot.
in the SD card slot.
• Do not insert anything other than an
Do not eject the SD card, as doing so SD card into the SD card slot.
may deactivate the navigation system. • Do not stick labels or stickers on SD
card. There is a possibility that it may
become impossible to eject the SD
card from inside the slot.
• Do not handle an SD card with wet
hands. Doing so may cause electric
shock or a malfunction.
• Do not allow hands or metal objects to
contact the interface pins of SD cards.
• Do not place SD cards on the instru-
ment panel, on any place with direct
sunlight or in areas with a lot of mois-
ture.
• Do not use SD cards in any place
CAUTION where static electricity or electric noise
adversely affects SD cards. This may
● SD cards cause data corruption or data loss.
• Keep away from children. These are • Always place the SD card in its storage
small and if swallowed by a child they case when not in use.
can cause choking. ● Do not edit or delete the map data on
the SD card, as doing so may deactivate
the navigation system.
INFORMATION
● microSDHC Logo is a trademark of SD-

3C,LLC.
254
9
1
Entune App Suite*
2
1 Entune App Suite OVERVIEW 3
1. Entune App Suite SERVICE ...... 256

BEFORE USING THE FUNCTION ...... 258 4
PREPARATION BEFORE USING 
Entune App Suite .............................. 259
5
2 Entune App Suite OPERATION

6
1. Entune App Suite ....................... 261
USING AN Entune App Suite............... 261
LINKING Entune App Suite AND 7
NAVIGATION FUNCTION................. 265
Entune App Suite KEYWORD 
OPERATION ..................................... 266 8
3 SETUP 9
1. Entune App Suite SETTINGS .... 268
*: Entune Premium Audio only (Available in the 48 states, D.C. and Alaska)
255
1. Entune App Suite OVERVIEW
1. Entune App Suite SERVICE
Entune App Suite is a service that enables downloadable applications to be dis-

played on and operated from the multimedia screen. Before Entune App Suite can
be used, a few actions need to be performed first. (P.259)
USB*1
256
No. Name Function
Content provider Provides content to the multimedia system via a cellular phone.
Provides downloadable application to the multimedia system

Application server
via a cellular phone.
Using the Entune App Suite application, communication is re-

layed between the multimedia system, the application server
*2 Cellular phone and the content provider.
For known compatible phones, refer to http://www.toyota.com/
entune/.
Downloaded Entune App Suite applications provide access to

Applications audio/visual content from a content provider when connected
via a compatible phone with a data connection.
Content received, via a cellular phone, from the content provid-

Multimedia system er’s server are displayed on the screen. The multimedia system
is equipped with an application player to run applications.
*1: iPhone only

*2: For known compatible phones, refer to http://www.toyota.com/entune/.
INFORMATION
● The actual service availability is dependent on the network condition.
Entune App Suite
257
BEFORE USING THE INITIALIZING PERSONAL

FUNCTION DATA
The personal data used in applications

SUBSCRIPTION can be removed from the multimedia
system. (P.60)
 User registration is required to start using
the Entune App Suite service.  The following personal data can be
 Entune App Suite does not require an acti- deleted from the system and returned to
vation fee or monthly recurring fees. their default settings:
 Services requiring a separate contract can • Downloaded applications
also be used.* • Downloaded application content
*: For details, refer to http://
www.toyota.com/entune/ or call 1-800- INFORMATION
331-4331. ● Once initialized, data will be erased from
the system. Pay close attention when
initializing the data.
AVAILABILITY OF SERVICE
 Entune App Suite is available in the con-
tiguous United States, D.C. and Alaska.
INFORMATION
● When using Entune App Suite, depend-
ing on the details of your cellular phone
contract, data usage fees may apply.
Confirm data usage fees before using
this service.
● In this section, the required actions to
activate applications, connect a cellular
phone to the navigation system and reg-
istration steps for Entune App Suite are
explained. For details regarding Entune
App Suite operations and each of the
applications, refer to http://www.toy-
ota.com/entune/.
● The actual service availability is depen-
dent on the cellular network condition.
258
PREPARATION BEFORE USER REGISTRATION

USING Entune App Suite 1 Perform user registration at http://
www.toyota.com/entune/.
SETUP REQUIRED TO USE
Entune App Suite REGISTERING THE Entune App
Perform the following actions. Suite APPLICATION
1 User registration 1 Download the Entune App Suite appli-

cation to your cellular phone.
2 Run the Entune App Suite application
2 Download the Entune App Suite ap-
on your cellular phone.
plication to your cellular phone.
3 Enter the information required into the
Entune App Suite application. Login to
3 Register the cellular phone to the mul- the application.
timedia system.
INFORMATION
● Applications can only be used when the
4 Download Entune App Suite applica- Entune App Suite application has been
tions to the multimedia system. downloaded to your cellular phone and
the application is running.
In order to use Entune App Suite, the fol- ● Entune App Suite operational
lowing actions must first be performed: procedures can also be confirmed by
 User registration with a service contract visiting http://www.toyota.com/entune/.
(P.259) ● In order to use applications, it is neces- 9
 Download the Entune App Suite applica- sary to run the Entune App Suite appli-
tion onto your cellular phone, and login to cation on your cellular phone.
the application. (P.259) ● For known phone compatibility Entune App Suite
information, refer to http://
 Register a Bluetooth® phone with the www.toyota.com/entune/.
hands-free system. (P.41)
● If an Entune App Suite application is
 Download Entune App Suite applications used while iPod audio is being played
to the multimedia system. (P.260) back, system operation may become
unstable.
259
DOWNLOADING Entune App

Suite APPLICATIONS
1 The actions on P.259 need to be per-

formed before Entune App Suite appli-
cations can be downloaded.
2 Once your phone is running the Entune
App Suite application with a valid ac-
count logged in and is connected to the
multimedia system, an on-screen pop-
up will be displayed offering to begin
downloading Entune App Suite appli-
cations to the multimedia system. After
download has started, see P.262 for
more information.
260
2. Entune App Suite OPERATION
1. Entune App Suite
USING AN Entune App Suite 2 Select the desired Entune App Suite
application.
Entune App Suite is a service that en-
ables the usable contents of a cellular
phone to be displayed on and operated
from the multimedia screen. Before
Entune App Suite can be used, a few
actions need to be performed first.
(P.259)
For details about the function and ser-
vice of each application, refer to http:// No. Function Page
www.toyota.com/entune/. Select to activate an appli-

cation.
Select to update the appli-
262
cation.
Select to reorder the appli-

35
cations.
Entune App Suite
261
UPDATING AN APPLICATION 3 Check that downloading is completed.
When Entune App Suite is activated,

an application may need to be updat-
ed. By updating, an application can be
updated to the latest version. When
updating the application, it is neces-
sary to download the updated data and
install it.
No. Function
■DOWNLOADING THE UPDATED
DATA Select to install the update later. The
screen will return to the last dis-
If an update is available, “Update” can played screen.
be selected. Select to display detailed informa-
tion about the updated data.
1 Select “Update”.
Select to install the updated data.
Follow the steps “INSTALLING THE
UPDATED DATA” from “STEP 2”.
(P.263)
INFORMATION
● Application download time may vary
based on the speed of the cellular net-
work.
2 Check that downloading is started.
● Application download can be resumed
after ignition off and back on.
● Future mandatory updates will display
an on-screen pop-up when available.
● Entune App Suite function cannot be
operated while mandatory updates
downloading.
“Download in Background”: Select to

operate other functions while download-
ing.
“Cancel”: Select to cancel updating.
262
■INSTALLING THE UPDATED DATA

After the downloading is complete,
“Update” will be changed to “Install”.
1 Select “Install”.
2 Select “Continue”.
“Later”: Select to postpone the installation

of the updated data and go back to the pre-
vious screen.
3 Check that installing is started.
“Install in Background”: Select to oper-
ate other function while installing.
4 Select “OK” after the installing is com-
plete.
9
INFORMATION
● Entune App Suite function cannot be
operated while installing. Entune App Suite
263
IF A MESSAGE APPEARS ON THE SCREEN
When problems occur starting up the application player, a message will appear on
the screen. Referring to the table below to identify the problem, take the suggested
corrective action. The following messages are only a few examples. If a message
other than the following is displayed, follow the instructions displayed on the
screen.
Message Display conditions Corrective action
Refer to http://
“The Phone is not connected.
The cellular phone cannot be www.toyota.com/entune/ to
For more information, please
connected. confirm if the phone is com-
visit toyota.com.”
patible or not.
Refer to http://
“To use the services, an ac- www.toyota.com/entune/ to
tive application needs to be The Entune App Suite appli- confirm if the phone is
running on your phone. For cation cannot be connected Bluetooth* SPP compatible or
more information, please visit to Bluetooth SPP. not, and then activate the En-
toyota.com.” tune App Suite application on
your phone.
*: Bluetooth is a registered trademark of Bluetooth SIG, Inc.
INFORMATION
● The actual messages displayed on screen may differ from the messages in this manual.
264
LINKING Entune App Suite SETTING A DESTINATION

AND NAVIGATION FUNCTION USING Entune App Suite
Locations that were searched using

The navigation system can set a desti-
Entune App Suite can be set as a des-
nation and make a hands-free call via
tination.
Entune App Suite. For details about
the function and service of each appli- 1 Display the “Web Search” screen.
cation, refer to http://www.toyota.com/ (P.265)
entune/.
2 Select the desired application button to
1 Press the “APPS” button. search.
3 Enter a search term, and select “GO”.
4 Select “Map”.
5 Select “Go to ”.
3 Select “Dest”.
4 Select “Web Search”.

6 Select “OK” to start guidance. 9
5 Check that the “Web Search” screen is

displayed. Entune App Suite
 For the operation of the route guidance

screen and the function of each screen
button: P.218
INFORMATION
● Actual sequence may vary based on the
application.
265
MAKING A PHONE CALL Entune App Suite KEYWORD

USING Entune App Suite OPERATION
Phone calls can be made to locations
Information can be entered to an
which were searched using Entune
Entune App Suite application by the
App Suite.
software keyboard or voice recognition
1 Display the “Web Search” screen. function. For details about the function
(P.265) and service of each application, refer
to http://www.toyota.com/entune/.
2 Select the desired application button to
search.  The keyboard layout can be changed.
3 Enter a search term, and select “GO”. (P.56)
4 Select “Call”.
USING THE SOFTWARE
5 Select “Yes”. KEYBOARD
“Cancel”: Select to cancel making a
phone call. 1 Display the “Apps” screen. (P.261)
6 Check that the “Call” screen is dis- 2 Select the desired Entune App Suite
played. application.
 For phone operation and the function of

3 Select the character input space.
each screen button: P.161
INFORMATION
● Actual sequence may vary based on the
application.
266
4 Enter a search term, and then select ENTERING A KEYWORD USING

“OK”. THE VOICE RECOGNITION
FUNCTION
1 Display the “Apps” screen. (P.261)
2 Select the desired Entune App Suite

application.
5 Entering characters will be reflected on

the character input space.
 For details on operating the keyboard:

P.36
3 Press the talk switch on the steering

INFORMATION
wheel once the application screen is
● Actual sequence may vary based on the displayed. (P.124)
application.
4 System will prompt for user input.
 End of user's speech will be detected
automatically, and the system will prompt
for any additional information if needed.
5 Search results will be displayed on the
screen. 9
Entune App Suite
267
3. SETUP
1. Entune App Suite SETTINGS
The phone data plan pop-up can be set

when a paid application is download-
ed.
3 Select “Entune”.
No. Function
Select to set the pop up reminder for

cellular phone data usage.
5 Select “OK”.
268
1
INDEX
2
269
ALPHABETICAL INDEX
A C
AAC.......................................................... 94 Calling on the Bluetooth® phone............ 154
AM............................................................ 77 Casual speech recognization ................. 129
APPS button ............................................ 12 CD ............................................................ 94
“Apps” screen........................................... 14 Playing an audio CD............................. 96
AUDIO button........................................... 12 Playing an MP3/WMA/AAC disc........... 96
Audio settings ........................................ 112 Command list ......................................... 130
AUX ........................................................ 109 Contacts ................................................. 156
Controls overview..................................... 12
B
®
Bluetooth ................................................ 41 D
Profiles ................................................. 43 Data services settings ............................ 138
Registering a Bluetooth® audio  Destination search screen...................... 205
player ................................................ 42 Driver settings .......................................... 63
Registering a Bluetooth® phone........... 41
Bluetooth® audio.................................... 105 E
®
Connecting a Bluetooth device ........ 108 Editing route ........................................... 228
Listening to Bluetooth® audio............. 108 Adding destinations ............................ 229
Bluetooth® phone................................... 150 Deleting destinations .......................... 229
Bluetooth® phone message function ..... 164
Detour setting ..................................... 230
Reordering destinations...................... 229
Selecting route type............................ 230
Setting route preferences ................... 229
Emergency ............................................. 215
Entering letters and numbers/
list screen operation ............................. 36
Entune App Suite ................................... 261
Entune App Suite keyword 
operation ......................................... 266
Linking Entune App Suite and 
navigation function .......................... 265
Using Entune App Suite application ....261
270
F M
FM radio................................................... 77 Maintenance ............................................ 64
Map database version and 
G covered area ...................................... 253
Map screen information ......................... 198
General settings....................................... 56
GPS (Global Positioning System).......... 251 Displaying information about 
the icon where the cursor is set ...... 200
Standard map icons ........................... 201
H
Map screen operation ............................ 193
Hands-free system.................................. 150
Adjusting location in small 
HOME button ........................................... 12 increments ...................................... 197
“Home” screen ......................................... 16 Current position display...................... 193
Home screen operation ........................... 34 Map scale ........................................... 193
Orientation of the map........................ 194
I
Screen scroll operation....................... 196
Incoming calls ......................................... 160 Switching the map mode .................... 194
Initial screen............................................. 30 Memory points settings .......................... 232
Internet radio............................................ 93 Deleting previous destinations ........... 240
iPod........................................................ 101 Setting up address book..................... 236
Setting up areas to avoid.................... 238
K
Setting up home ................................. 233
Keyboard ................................................. 36 Setting up preset destinations ............ 234
Message ................................................. 164
Microphone ............................................ 124
MP3.......................................................... 94
271
ALPHABETICAL INDEX
N S
Navigation .............................................. 189 Satellite Radio .......................................... 87
Navigation option screen ........................ 192 Screen adjustment ................................... 39
SD card ...................................................254
P Search operation.................................... 207
Phone/message settings........................ 169 Searching by address......................... 209
“Contact/Call History Settings”  Searching by address book ................ 214
screen ............................................. 171 Searching by coordinates ................... 217
“Messaging Settings” screen.............. 179 Searching by emergency.................... 215
“Phone Display Settings” screen ........ 180 Searching by intersection and 
“Sound Settings” screen..................... 170 freeway ........................................... 215
PWR·VOL button ..................................... 12 Searching by map............................... 217
Searching by point of interest ............. 210
R Searching from previous 
destinations..................................... 214
Radio............................................. 77, 87, 93
Selecting search area......................... 208
Rear view monitor system...................... 140
Setting home as destination ............... 208
Registering home..................................... 22
Setting preset destinations 
Registering preset destinations................ 24
as destination.................................. 208
Registering/connecting Bluetooth® 
Setting Bluetooth® details ........................ 49
device ................................................... 41
“Bluetooth Setup” screen...................... 49
Certification .......................................... 45
Connecting a Bluetooth® device........... 51
Profiles ................................................. 43
Deleting a Bluetooth® device................ 51
Registering a Bluetooth® audio player 
for the first time ................................. 42 Editing the Bluetooth® device 
information ........................................ 53
Registering a Bluetooth® phone 
for the first time ................................. 41 Registering a Bluetooth® device........... 50
Route guidance screen .......................... 222 “System Settings” screen ..................... 54
During freeway driving........................ 224 Setting home as the destination............... 26
Route overview................................... 223 “Setup” screen.......................................... 20
Screen for route guidance .................. 222 Sound setting ............................................56
Turn list screen................................... 226 Starting route guidance .......................... 218
Turn-by-turn arrow screen.................. 226 Steering switches ................................... 111
When approaching intersection.......... 225
Route trace ............................................ 200
272
T
Talking on the Bluetooth® phone........... 161
Touch screen gestures ............................ 32
Touch screen operation ........................... 33
Traffic information .................................. 202
Traffic map information ........................... 137
Traffic settings ....................................... 245
Auto avoid traffic ................................ 246
My traffic routes.................................. 247
Screen for traffic settings ................... 245
Troubleshooting ..................................... 181
TUNE·SCROLL button ............................ 12
Typical voice guidance prompts ............ 227
U
USB/AUX port.......................................... 74
USB memory ........................................... 97
V
Vehicle settings........................................ 62
Voice command system......................... 124
Voice settings .......................................... 61
W
Weather information ............................... 136
WMA ........................................................ 94
X
XM Satellite Radio ................................... 87
273
Map database information and updates
274
275
276
277
278
279
280
Certain business data provided by Infogroup © 2014, All Rights Reserved.
281
Certification
 Gracenote, the Gracenote logo and logotype, “Powered by Gracenote”, MusicID, Playlist
Plus and MediaVOCS are either registered trademarks or trademarks of Gracenote, Inc.
in the United States and/or other countries
282
283
For U.S. owners
284

Toyota Navigation System Reference Guide

Uploaded by

Copyright:

Available Formats

Toyota Navigation System Reference Guide

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Toyota Navigation System Reference Guide

Uploaded by

Copyright:

Available Formats

What is the navigation system designed to do?

What is the navigation system designed to do?

What does the navigation system use to determine position and guide to destinations?

What does the navigation system use to determine position and guide to destinations?

1 QUICK GUIDE 11

4 VOICE COMMAND SYSTEM 123

6 PERIPHERAL MONITORING SYSTEM 139

8 NAVIGATION SYSTEM* 189

9 Entune App Suite* 255

*: Entune Premium Audio only

NAVIGATION SYSTEM OWNER’S MANUAL

SYMBOLS USED IN ILLUSTRATIONS

Arrows indicating operations

No. Name Description

Main Operations The steps of an operation are explained.

Related Operations A main operation’s supplementary operations are described.

Information Useful information for the user is described.

To use this system in the safest possible

● For safety, the driver should not operate

1 QUICK GUIDE 2 BASIC FUNCTION

1. CONTROLS AND FEATURES ........ 12 1. BASIC INFORMATION BEFORE 

FUNCTION INDEX ................................ 27 3. OTHER SETTINGS ......................... 56

1. BASIC OPERATION........................ 70 1. INFORMATION ............................. 136

6. TIPS FOR OPERATING  1. PHONE OPERATION 

8 NAVIGATION SYSTEM 9 Entune App Suite

1. BASIC OPERATION...................... 190 1. Entune App Suite OVERVIEW .... 256

1 CONTROLS AND FEATURES 3

1. CONTROLS OVERVIEW .............. 12

3. “Home” SCREEN ......................... 16

4. “Setup” SCREEN ......................... 20

4. SETTING HOME AS THE

1. FUNCTION INDEX ........................ 27

Entune Premium Audio

Entune Audio Plus

No. Function Page

Press to access the Bluetooth® hands-free system and applications. 149

Turn to select a radio station or skip to the next or previous track/file.

Map card slot

Press to pause or resume playing music. —

Press to display the “Apps” screen. 14, 35

Press to display the “Home” screen. 16, 34

Press to eject a disc. 74

Press the “APPS” button to display the “Apps” screen.

Entune Audio Plus

No. Function Page

Select to display the hands-free operation screen. 150

Select to display the “Messages” screen. 164

* Select to display weather information. 136

Select to reorder the applications. 35

* Select to display traffic incidents. 202

* Select to display the traffic map information. 137

Select to display the “Setup” screen. 20

* Select to update the Entune App Suite applications. 262

Select to display the “Maintenance” screen. 64

* Select to display the application screen. 256

If a turn-by-turn navigation application has been downloaded to a con-

*: Available in the 48 states, D.C. and Alaska

Press the “HOME” button to display the “Home” screen.

Two-way split screen