Scribd
Upload
70 views

IR Sensor Module (Making)

An IR sensor module transmits and receives infrared rays to detect surfaces and objects. It contains an IR transmitter, IR receiver, voltage regulator, capacitors, resistors, LEDs, and an op-amp integrated circuit. The document provides step-by-step instructions to build the IR sensor module on a breadboard, including setting up the 5V power supply, connecting the IR transmitter and receiver, and using the op-amp IC to compare the sensor inputs and light an LED if infrared light is detected. The module can be used in robotics applications like line following and obstacle avoidance.

Uploaded by

Amol Patil
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
70 views

IR Sensor Module (Making)

An IR sensor module transmits and receives infrared rays to detect surfaces and objects. It contains an IR transmitter, IR receiver, voltage regulator, capacitors, resistors, LEDs, and an op-amp integrated circuit. The document provides step-by-step instructions to build the IR sensor module on a breadboard, including setting up the 5V power supply, connecting the IR transmitter and receiver, and using the op-amp IC to compare the sensor inputs and light an LED if infrared light is detected. The module can be used in robotics applications like line following and obstacle avoidance.

Uploaded by

Amol Patil
Copyright
© © All Rights Reserved
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 5

Making of IR Sensor Module

An IR Sensor module is a sensor that


transmits and receives infra-red rays when a surface
or object is detected. It is a multipurpose sensor,
which can be used in line following robot, obstacle
avoiding robot, edge avoiding robot, etc.
Components required:

 Breadboard – 1 no
 IC LM358 – 1 no
 IC 7805 – 1 no
 IR Transmitter – 1 no
 IR Receiver – 1 no
 10µf Capacitors – 2 nos
 9V Battery – 1 no
 Battery Snap – 1 no
 10K Trimpot – 1 no
 LED – 2 nos
 10K Resistor – 2 nos
 1K Resistor – 2 nos
 Breadboard Wires
Circuit Diagram:

Step by Step Instructions:


1) 5V Power Supply:

 Take the breadboard and connect the battery


holder in horizontal position.
 Insert the positive and negative wire of battery
snap in holder.
 Attach IC 7805 (Voltage Regulator), and place
one 10 µF capacitor in IN & GND connection of IC
7805 and other in GND & OUT connection.
 Take the positive supply from the battery holder
via breadboard wire and place it in IN of IC 7805,
and also connect its negative supply in the last
row of the breadboard.
 Place the GND of IC 7805 in the last row of the
breadboard, and transfer its OUT to the first row
of the breadboard.
 As a result of these connections, +5V power is
obtained in the first row of the breadboard.
 To check the power flow path, an LED is given a
positive supply via 10K resistor.
2) IC LM358:

 Take an IC LM358 and place it in the breadboard.


 Provide +5V to the 8th pin and GND to the 4thpin
of LM358.
 Connect the LED’s +ve with the 1st pin of LM358
via 1K resistor and –ve to the GND.
3) IR Transmitter:

 Place the IR transmitter in the breadboard and


provide +5V to its cathode.
 A GND connection is given to its anode via the
10K resistor.
4) IR Receiver:
 Place the IR receiver in the breadboard and
provide +5V to its anode.
 A GND connection is given to its cathode via the
10K resistor.
 Connect the IR receiver’s cathode with the 3rdpin
of LM358 using breadboard connection.
5) Trim pot:

 Place a 10K trimpot in the breadboard, and


provide +5V to its 1st pin and GND to its 3rdpin.
 Connect its 2nd pin with the 2nd pin of LM358.
Working:

Once the connection is finished, make sure the


connections are given as per the circuit diagram.
Now, show your hand towards the IR transmitter
and receiver. In this case, an LED connected to the
1st pin of LM358 must glow as the IR transmitter
emits IR rays and IR receiver receives the reflected
ray.
The Op-Amp (IC LM358) compares the two inputs
and provides the output which is higher.
If the LED fails to glow, then there is a problem in the
circuit.
Conclusion:

Overall, I feel the making of IR Sensor Module would


help my reader’s in developing the robots. This IR
Sensor Module is recommended to be designed in
PCB for better and reliable uses.
If you have any doubt, please feel free to drop a mail
at [email protected]
The below video brings you the working of the IR
Sensor Module in the breadboard:
https://youtu.be/ROynLWmXjSE

You might also like