Thank you for purchasing a JVC product.

KD-R210 Please read all instructions carefully before operation, to ensure your complete understanding and to obtain the best
possible performance from the unit.
CD RECEIVER: INSTRUCTIONS/INSTALLATION Installation/connection are explained at the last section of this manual (reverse page, indicated with
symbol).

For customer Use:

Enter below the Model No. and Serial No. which
are located on the top or bottom of the cabinet.
Retain this information for future reference.
Model No. 0809DTSMDTJEIN
GET0621-001A EN
[J] Serial No.
© 2009 Victor Company of Japan, Limited
ENGLISH ESPAÑOL

CANCELING THE DISPLAY DEMONSTRATIONS PREPARATIONS

Turn on the power. Select “DEMO OFF.” How to reset your unit Attaching the control panel
Reset the unit after installation is complete.

Finish the procedure.

(Initial setting)
Detaching the control panel
• Your preset adjustments will also be erased.
SETTING THE CLOCK How to forcibly eject a disc

Turn on the power. Select “CLOCK M.”

• Be careful not to drop the disc when it ejects.
• If this does not work, reset your unit.

Adjust the minute.

PREPARING THE REMOTE CONTROLLER (RM-RK50)
When you use remote controller for the first time... If the effectiveness of the remote controller
(Initial setting)
decreases, replace the battery.

Select “CLOCK H.” Replacing the lithium coin battery

Finish the procedure.
Insulation sheet

For USA-California Only: This product contains a CR

Coin Cell Lithium Battery which contains Perchlorate
Adjust the hour. Material—special handling may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate Warning: To prevent accidents and damage
• Do not install any battery other than CR2025 or its
Caution: equivalent.
• Danger of explosion if battery is incorrectly replaced. • Store out of reach of children.
Replace only with the same or equivalent type. • Do not recharge, short, or dismantle.
INFORMATION (For U.S.A.) • Battery shall not be exposed to excessive heat such as • Do not dispose of in fire.
sunshine, fire, or the like. • Do not carry around with other metallic materials.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used MORE ABOUT THIS UNIT
in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference Basic operations – There are improper recording conditions (missing data,
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to • By pressing SRC on the unit, you can also turn on the etc.) or media conditions (stained, scratched, warped,
try to correct the interference by one or more of the following measures: power. If the source is ready, playback also starts. etc.).
• If you turn off the power while listening to a disc, disc • CD-RWs may require a longer readout time since the
– Reorient or relocate the receiving antenna. reflectance of CD-RWs is lower than that of regular CDs.
– Increase the separation between the equipment and receiver. play will start from where it had been stopped previously
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. next time you turn on the power. Playing an MP3/WMA disc
– Consult the dealer or an experienced radio/TV technician for help. • When no disc is loaded in the unit, you cannot select “CD” • This unit can play back MP3/WMA files with the
as the playback source. extension code <.mp3> or <.wma> (regardless of the
Caution letter case—upper/lower).
Changes or modifications not approved by JVC could void the user’s authority to operate the equipment. Tuner operations • This unit can show the names of albums, artists
• During SSM search... (performer), and tag (Version 1.0, 1.1, 2.2, 2.3, or 2.4) for
– All previously stored stations are erased and the MP3 files and for WMA files.
IMPORTANT FOR LASER PRODUCTS stations are stored anew. • This unit can display only one-byte characters. No other
1. CLASS 1 LASER PRODUCT – Received stations are preset in No. 1 (lowest characters can be correctly displayed.
2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all servicing to qualified frequency) to No. 6 (highest frequency). • This unit can play back MP3/WMA files meeting the
service personnel. – When SSM is over, the station stored in No. 1 will be conditions below:
3. CAUTION: (For U.S.A.) Visible and/or invisible class II laser radiation when open. Do not stare into beam. automatically tuned in. – Bit rate: 8 kbps — 320 kbps
(For Canada) Visible and/or invisible class 1M laser radiation when open. Do not view directly with optical – Sampling frequency:
instruments. Disc operations 48 kHz, 44.1 kHz, 32 kHz (for MPEG-1)
24 kHz, 22.05 kHz, 16 kHz (for MPEG-2)
4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT. Caution for DualDisc playback – Disc format: ISO 9660 Level 1/ Level 2, Romeo, Joliet,
• The Non-DVD side of a “DualDisc” does not comply with Windows long file name
the “Compact Disc Digital Audio” standard. Therefore, the • The maximum number of characters for file/folder names
use of Non-DVD side of a DualDisc on this product may vary depending on the disc format used (includes 4
not be recommended. extension characters—<.mp3> or <.wma>).
General – ISO 9660 Level 1: up to 12 characters; ISO 9660 Level 2:
• This unit has been designed to reproduce CDs/CD Texts, up to 31 characters; Romeo: up to 64 characters; Joliet:
and CD-Rs (Recordable)/CD-RWs (Rewritable) in audio CD up to 32 characters; Windows long file name: up to 126
(CD-DA) and MP3/WMA formats. characters
[European Union only] • This unit can recognize a total of 512 files, 255 folders,
• After ejecting a disc, “NO DISC” appears and you cannot
and 8 hierarchical levels.
operate some of the buttons. Insert another disc or press
• This unit can play back files recorded in VBR (variable bit
SRC to select another playback source.
rate).
For safety... Warning Playing a CD-R or CD-RW Files recorded in VBR have a discrepancy in the elapsed
• Do not raise the volume level too much, as this will block If you need to operate the unit while driving, be sure to • Use only “finalized” CD-Rs or CD-RWs. time display, and do not show the actual elapsed time.
outside sounds, making driving dangerous. look around carefully or you may be involved in a traffic • This unit can play back multi-session discs; however, In particular, this difference becomes noticeable after
unclosed sessions will be skipped while playing. performing the search function.
• Stop the car before performing any complicated accident. • This unit cannot play back the following files:
• Some CD-Rs or CD-RWs may not be played back on this
operations. – MP3 files encoded in: MP3i and MP3 PRO format, in an
Caution on volume setting unit:
– Discs are dirty or scratched. inappropriate format, layer 1/2.
Temperature inside the car... Discs produce very little noise compared with other sources. – WMA files: encoded in lossless, professional, and voice
– Moisture condensation has occurred on the lens inside
If you have parked the car for a long time in hot or cold Lower the volume before playing a disc to avoid damaging the unit. format; not based upon Windows Media® Audio; copy-
weather, wait until the temperature in the car becomes the speakers by the sudden increase of the output level. – The pickup lens inside the unit is dirty. protected with DRM.
normal before operating the unit. – The files on the CD-R/CD-RW are written using the – Files which have data such as WAVE, ATRAC3, etc.
“Packet Write” method. • The search function works but search speed is not constant.
1– EN

EN_KD-R210[J]f.indd 1 14/8/09 2:50:14 PM

 OPERATIONS

INSTRUCTIONS
Basic operations Disc operations
Control panel Remote sensor Check the current clock time/other information.
• Turn on the power. DO NOT expose to strong light. See also “CLK DISP“ of “General settings—PSM.”
• Turn off the power [Hold].
• Attenuate the sound (if the
power is on). Eject disc.
• Press SRC to
listen to another
playback source.
Detach the panel.

Select the source. Volume control. • 4 /¢ [Press] Select track (for CD) or folder* (for MP3/
[Press] Go to the next or previous track. WMA) number (01 – 06).
[Hold] Fast-forwards or reverses the track. [Hold] Select track (for CD) or folder* (for MP3/
Display window • 5 / ∞ : Go to the next or previous folder WMA) number (07 – 12).
• MO: Lights up in monaural mode. (for MP3/WMA discs). * Folders are required to assigned with 2-digit
• Source display • ST: Lights up when receiving an FM stereo numbers at the beginning.
• Track number Playback mode indicator broadcast with sufficient signal strength.
• Folder number
(for MP3/WMA discs) Disc indicator Disc information indicators Turn on the power.
• Volume level indicator Insert disc.
• Time countdown indicator All tracks will be played repeatedly until you change the source or eject the disc.

Main display (time, LOUD (loudness)

Tr (track) indicator playback information) indicator Selecting the playback modes Changing the display information
After pressing M MODE, press the following buttons to...
Remote controller—RM-RK50 TRK RPT : Plays the current track
• Turns the power on if pressed briefly or • Selects the sound mode repeatedly.
attenuates the sound when power is on. (iEQ: intelligent equalizer). FLDR RPT* : Plays all tracks of the current While playing an audio While playing an MP3 or
• Turns the power off if pressed and held. folder repeatedly. CD or CD Text a WMA disc
• Selects the source. RPT OFF : Cancels.
• Changes the FM/AM bands with 5 U.
• Changes the preset stations with D ∞. • Searches for stations if pressed briefly. FLDR RND* : Plays all tracks of the current
• Changes the folders of MP3/WMA discs. • Fast-forwards or reverses the track if folder, then the tracks of the
pressed and held. next folder at random.
• Changes the track of the disc if pressed ALL RND : Plays all tracks of the current
• Adjusts the volume level. briefly. disc at random.
RND OFF : Cancels. : Clock with the current track number
: The elapsed playing time with the current track
* Only for MP3/WMA. number
Radio operations *1 If the current disc is an audio CD, “NO NAME” appears.
Skipping a track quickly during play *2 If an MP3/WMA file does not have tags or “TAG DISP” is
• For MP3/WMA disc, you can skip a track within the set to “TAG OFF,” folder name and file name appear.
same folder.
Example: Select track 32 Prohibiting disc ejection
You can lock a disc in the loading slot.

Select preset station.

• You can also use 5 / ∞ to select preset station. To cancel the prohibition, repeat the same procedure.

Select “FM/AM.”
Select the bands.
Search for a station—Auto Search. External component operations
Manual Search: Hold either one of the buttons until “M” flashes on the display, then press it repeatedly.
You can connect an external component to the AUX (auxiliary) input jack on the control panel.
When an FM stereo broadcast is hard to receive
Reception improves, but the stereo effect will be lost.
Turn on the connected
• MO indicator lights up.
component and start
To restore the stereo effect, repeat the same procedure.
playing the source.
FM station automatic presetting—SSM (Strong-station Sequential Memory)
You can preset six stations for each band.

Manual presetting Portable audio player, etc.

Example: Storing the FM station of 92.5 MHz into preset number 4 of the FM1 band. Stereo mini plug (not supplied)

MAINTENANCE
How to clean the connectors To keep discs clean
Do not use the following discs:
Wipe the connectors with Wipe in a straight line from center of disc to
Single CD—8 cm (3-3/16”) disc Warped disc Sticker and sticker residue Stick-on label
a cotton swab or cloth edge. Do not use liquid cleaners, thinners, or
moistened with alcohol. benzene.
Connectors
Moisture condensation To play new discs Transparent or semi-transparent
Moisture may condense on the lens inside the unit. Eject Remove any rough areas from the inner and Unusual shape C-thru Disc (semi-transparent disc) parts on its recording area
the disc and leave the unit turned on for a few hours until outer edges of the disc.
the moisture has evaporated.

2– EN

EN_KD-R210[J]f.indd 2 14/8/09 2:50:18 PM

 SETTINGS TROUBLESHOOTING

INSTRUCTIONS
Sound adjustments Symptoms Remedies/Causes

• Sound cannot be heard from the speakers. • Adjust the volume to the optimum level.
• Check the cords and connections.

General
Preset values BAS MID TRE LOUD
Indication (For) (bass) (mid-range) (treble) (loudness) • The buttons on the unit do not work as you If you press M MODE, some buttons work differently from it
intended. original function. Wait for 5 seconds or press M MODE again.
USER (Flat sound) 00 00 00 OFF
ROCK (Rock or disco music) +03 00 +02 OFF • This unit does not work at all. Reset the unit.
CLASSIC (Classical music) +01 00 +03 OFF • SSM automatic presetting does not work. Store stations manually.

FM/AM
POPS (Light music) +02 +01 +02 OFF
• Static noise while listening to the radio. Connect the antenna firmly.
HIP HOP (Funk or rap music) +04 –02 +01 OFF
• Disc ejects. Insert the disc correctly.
JAZZ (Jazz music) +03 00 +03 OFF
• CD-R/CD-RW cannot be played back. • Insert a finalized CD-R/CD-RW.
Adjusting the sound • Tracks on the CD-R/CD-RW cannot be • Finalize the CD-R/CD-RW with the component which you used
skipped. for recording.

Disc playback
• Disc can be neither played back nor ejected. • Unlock the disc.
• Eject the disc forcibly.

• Disc sound is sometimes interrupted. • Stop playback while driving on rough roads.
2
BAS* (bass) : Adjust the bass. –06 to +06 • Change the disc.
• Check the cords and connections.
MID*2 (mid-range) : Adjust the middle frequencies sound level. –06 to +06
2
TRE* (treble) : Adjust the treble. –06 to +06 • “NO DISC” appears on the display. Insert a playable disc into the loading slot.
• “PLEASE” and “EJECT” appear alternately
3
FAD* (fader) : Adjust the front and rear speaker balance. R06 to F06 on the display.
BAL (balance) : Adjust the left and right speaker balance. L06 to R06
• Disc cannot be played back. • Use a disc with MP3/WMA tracks recorded in a format compliant
LOUD*4 (loudness) : Boost low and high frequencies to produce a well-balanced sound LOUD ON or LOUD OFF with ISO 9660 Level 1, Level 2, Romeo, or Joliet.
at a low volume level. • Add the extension code <.mp3> or <.wma> to the file names.
SUB.W (subwoofer) : Adjust the subwoofer output level. 00 to 08
• Noise is generated. Skip to another track or change the disc. (Do not add the extension
VOL (volume) : Adjust the volume. 00 to 50 (or 00 to 30)*5 code <.mp3> or <.wma> to non-MP3 or WMA tracks.)
MP3/WMA playback

*1 Displayed only when “L/O MODE” is set to “WOOFER.”

• A longer readout time is required Do not use too many hierarchical levels and folders.
*2 When you adjust the bass, mid-range, or treble, the adjustment you have made is stored for the currently selected sound
(“READING” keeps flashing on the display).
mode (iEQ) including “USER.”
*3 If you are using a two-speaker system, set the fader level to “00.” • Tracks are not played back in the order you Playback order is determined when the files are recorded.
*4 The adjustment made (LOUD ON/LOUD OFF) will be applied to all sound modes (iEQ). have intended.
*5 Depending on the amplifier gain control setting.
• The elapsed playing time is not correct. This sometimes occurs during playback. This is caused by how the
tracks are recorded on the disc.
General settings—PSM
• The correct characters are not displayed This unit can only display alphabets (upper case), numbers, and a
Enter PSM menu. Select an item. Adjust. Finish. (e.g. album name). limited number of symbols.

• Microsoft and Windows Media are either registered trademarks or trademarks of Microsoft Corporation in the United
States and/or other countries.

Indication Item ( : Initial) Setting

DEMO • DEMO ON : Display demonstration will be activated automatically if no operation is done SPECIFICATIONS
for about 20 seconds.
• DEMO OFF : Cancels. Audio amplifier section CD player section
CLK DISP *6 • ON : Clock time is shown on the display at all times when the power is turned off. Power Output: Type: Compact disc player
• OFF : Cancels; pressing DISP will show the clock time for about 5 seconds when the 20 W RMS × 4 Channels at 4 Ω and Signal Detection System: Non-contact optical pickup
power is turned off. ≤ 1% THD+N (semiconductor laser)
CLOCK H (Hour) 1 – 12 : [Initial: 1 (1:00)] Signal-to-Noise Ratio: Number of channels: 2 channels (stereo)
80 dBA (reference: 1 W into 4 Ω) Frequency Response: 5 Hz to 20 000 Hz
CLOCK M (Minute) 00 – 59 : [Initial: 00 (1:00)] Dynamic Range: 93 dB
DIMMER • ON : Dims the display and button illumination. Load Impedance: 4 Ω (4 Ω to 8 Ω allowance) Signal-to-Noise Ratio: 98 dB
• OFF : Cancels. Tone Control Range: Bass: ±12 dB at 60 Hz Wow and Flutter: Less than measurable limit
Mid-range: ±12 dB at 1 kHz MP3 Decoding Format: MPEG1/2 Audio Layer 3
SCROLL *7 • ONCE : Scrolls the displayed information once.
Treble: ±12 dB at 7.5 kHz Max. Bit Rate: 320 kbps
• AUTO : Repeats scrolling (at 5-second intervals).
Frequency Response: 40 Hz to 20 000 Hz WMA (Windows Media® Audio) Decoding Format :
• OFF : Cancels.
Line-Out Level/Impedance: 2.5 V/20 kΩ load (full scale) Max. Bit Rate: 192 kbps
• Pressing DISP for more than one second can scroll the display regardless of
the setting. Output Impedance: 1 kΩ
Subwoofer-Out Level/Impedance:
L/O MODE • REAR : Select if the REAR LINE OUT terminals are used for connecting the speakers
(through an external amplifier).
2.5 V/20 kΩ load (full scale) General
• WOOFER : Select if the REAR LINE OUT terminals are used for connecting a subwoofer. Power Requirement: Operating Voltage: DC 14.4 V
(11 V to 16 V allowance)
WOOFER *8 • LOW : Frequencies lower than 90 Hz are sent to the subwoofer. Tuner section Grounding System: Negative ground
• MID : Frequencies lower than 135 Hz are sent to the subwoofer. Allowable Operating Temperature:
Frequency Range:
• HIGH : Frequencies lower than 180 Hz are sent to the subwoofer. 0°C to +40°C (32°F to 104°F)
FM: 87.5 MHz to 107.9 MHz
AUX ADJ A.ADJ 00 : Adjust the auxiliary input level to avoid the sudden increase of the output (with channel interval set to 100 kHz or 200 kHz) Dimensions (W × H × D):
– A.ADJ 05 level when changing the source from external component connected to the 87.5 MHz to 108.0 MHz Installation Size (approx.):
AUX input jack on the control panel. (with channel interval set to 50 kHz) 182 mm × 52 mm × 160 mm
AM: 530 kHz to 1 710 kHz (7-3/16” × 2-1/16” × 6-5/16”)
TAG DISP • TAG ON : Shows the Tag while playing MP3/WMA tracks.
(with channel interval set to 10 kHz) Panel Size (approx.):
• TAG OFF : Cancels.
531 kHz to 1 602 kHz 188 mm × 58 mm × 5 mm
AMP GAIN *9 • LOW PWR : VOL 00 – VOL 30 (Select if the maximum power of each speaker is less than (with channel interval set to 9 kHz) (7-7/16” × 2-5/16” × 1/4”)
50 W to prevent damaging the speaker.) Mass (approx.):
• HIGH PWR : VOL 00 – VOL 50 [FM Tuner] 1.3 kg (2.9 lbs) (excluding accessories)
AREA • AREA US : When using in North/Central/South America. AM/FM intervals are set to Usable Sensitivity: 11.3 dBf (1.0 μV/75 Ω)
10 kHz/200 kHz. 50 dB Quieting Sensitivity: 16.3 dBf (1.8 μV/75 Ω) Design and specifications are subject to change without
• AREA EU : When using in any other areas. AM/FM intervals are set to 9 kHz/50 kHz Alternate Channel Selectivity (400 kHz): 65 dB notice.
(100 kHz during auto search). Frequency Response: 40 Hz to 15 000 Hz
• AREA SA : When using in South American countries where FM interval is 100kHz. Stereo Separation: 35 dB
AM interval is set to 10kHz. [AM Tuner]
Sensitivity/Selectivity: 20 μV/35 dB
Having TROUBLE with operation?
*6 If the power supply is not interrupted by turning off the ignition key of your car, it is recommended that you select “OFF” to
save the car’s battery. Please reset your unit
*7 Some characters or symbols will not be shown correctly (or will be blanked) on the display. Still having trouble??
*8 Displayed only when “L/O MODE” is set to “WOOFER.” If a kit is necessary for your car, consult your telephone Call 1-800-252-5722 (USA ONLY)
*9 The volume level automatically changes to “VOL 30” if you change to “LOW PWR” while the volume level is set higher than directory for the nearest car audio speciality shop. http://www.jvc.com
“VOL 30.”
3– EN

EN_KD-R210[J]f.indd 3 14/8/09 2:50:20 PM

 INSTALLATION / CONNECTION
PREPARATION WARNINGS TROUBLESHOOTING
This unit is designed to operate on 12 V DC, NEGATIVE ground electrical To prevent short circuits, we recommend that you disconnect the battery’s • The fuse blows.
systems. If your vehicle does not have this system, a voltage inverter is required, negative terminal and make all electrical connections before installing the unit. * Are the red and black leads connected correctly?
which can be purchased at JVC car audio dealers. • Be sure to ground this unit to the car’s chassis again after installation. • Power cannot be turned on.
* Is the yellow lead connected?
Notes:
Prepare this before installation • Replace the fuse with one of the specified rating. If the fuse blows frequently, • No sound from the speakers.
consult your JVC car audio dealer. * Is the speaker output lead short-circuited?
• It is recommended to connect to the speakers with maximum power of more • Sound is distorted.
than 50 W (both at the rear and at the front, with an impedance of 4 Ω to * Is the speaker output lead grounded?
8 Ω). If the maximum power is less than 50 W, change “AMP GAIN” setting to * Are the “–” terminals of L and R speakers grounded in common?
prevent the speakers from being damaged • Noise interfere with sounds.
(see “General settings—PSM”). * Is the rear ground terminal connected to the car’s chassis using shorter and
• To prevent short-circuit, cover the terminals thicker cords?
of the UNUSED leads with insulating tape. • This unit becomes hot.
• The heat sink becomes very hot after use. Be * Is the speaker output lead grounded?
careful not to touch it when removing this * Are the “–” terminals of L and R speakers grounded in common?
unit. Heat sink • This unit does not work at all.
* Have you reset your unit?

Parts list for installation and connection ELECTRICAL CONNECTIONS

Typical connections
A B C
Control panel Sleeve Trim plate Before connecting: Check the wiring in the vehicle carefully. Incorrect connection may cause serious damage to this
unit. The leads of the power cord and those of the connector from the car body may be different in color.
1 Connect the colored leads of the power cord in the order specified in the illustration below.
2 Connect the antenna cord.
3 Finally connect the wiring harness to the unit.
D E F
Power cord Handles Remote controller Rear line out Rear ground terminal
/ Battery
Antenna
15 A fuse
terminal

INSTALLATION Ignition switch

Black To the metallic body
The following illustration shows a typical installation. If you have any questions or require information regarding installation or chassis of the car
kits, consult your JVC car audio dealer or a company supplying kits. Connect only the front speakers if your
• If you are not sure how to install this unit correctly, have it installed by a qualified technician. speaker system is two-speaker system. To a live terminal in the
Yellow * 2 fuse block connecting to
White with black stripe the car battery (bypassing
In dash-mounting
the ignition switch)
(constant 12 V)
Front speaker (left) White Fuse block
Red To an accessory terminal
Gray with black stripe in the fuse block
Blue with
white stripe To the remote lead of other
Front speaker (right) Gray equipment or automatic antenna if
any (200 mA max.)
When you stand the unit, Green with black stripe
be careful not to damage
Do the required the fuse on the rear.
IMPORTANT
electrical connections. Rear speaker (left) Green
Purple with black stripe

Rear speaker (right) Purple

RECOMMENDED CONNECTION
Custom wiring harness *1

Bend the appropriate tabs Connecting the external amplifier or subwoofer

to hold the sleeve firmly in
place. Remote lead Y-connector *1

Install the unit at an angle of Set “L/O MODE” to “REAR” Remote lead (blue with white stripe)
less than 30˚. (See “General settings—PSM.”)
You can connect a power amplifier for To the remote lead of other equipment
rear speakers. or automatic antenna if any
When installing the unit without using the sleeve
In a Toyota car for example, first remove the car radio and install the unit in its place. JVC Amplifier
Flat type screws—M5 × 8 mm (M5 × 3/8")*
Rear
speakers Right
Bracket* Left Front speakers
Set “L/O MODE” to “WOOFER”
Flat type screws (See “General settings—PSM.”)
—M5 × 8 mm (M5 × 3/8")* You can also connect a subwoofer to
Pocket *1 Not supplied for this unit.
Bracket* * Not supplied for this unit. the REAR LINE OUT terminals. *2 Before checking the operation of this unit prior to installation, this
or lead must be connected, otherwise the power cannot be turned on.
Removing the unit JVC Amplifier *3 Firmly attach the ground wire to the metallic body or to the chassis
Subwoofer of the car—to the place uncoated with paint (if coated with paint,
Before removing the unit, release the rear section. remove the paint before attaching the wire). Failure to do so may
cause damage to the unit.
*4 Signal cord (not supplied for this unit)

PRECAUTIONS on power supply and speaker connections:

• DO NOT connect the speaker leads of the power cord to the car battery; otherwise, the unit will be
seriously damaged.
• BEFORE connecting the speaker leads of the power cord to the speakers, check the speaker wiring in your car.

4– EN

EN_KD-R210[J]f.indd 4 14/8/09 2:50:22 PM